ETM350C ETM450C User Manual 201405RV01

ETM350C ETM450C User Manual 201405RV01.docx

3G Industrial Ethernet Router

ETM350C & ETM450C

User Manual

Features:

◩ HSDPA/UMTS 850/900/2100MHz // 850/900/1900/2100MHz

◩ GSM/GPRS 900/1800MHz // 850/900/1800/1900MHz

◩ HSPA 14.4Mbps DL, 5.76Mbps UL (ETM450C only)

◩ UMTS 384Kbps UL, 384Kbps DL

◩ 1 x Ethernet Port 10/100Mbps

◩ RJ12 Port for power connection

◩ SMA Antenna Connector

◩ Supports Dual SIM with automatic failover

Page 2 of 24 For Support Contact +61-2-9956-7377

Or [email protected]

Contents

Introduction ........................................................................................................................................ 3

Nomenclature .................................................................................................................................. 3

Overview. ....................................................................................................................................... 3

Applications .................................................................................................................................... 3

Specifications ...................................................................................................................................... 4

Product Drawing ................................................................................................................................. 4

Power Supply ...................................................................................................................................... 5

SIM Card ............................................................................................................................................ 5

SIM Pin ...................................................................................................................................................... 5

Indicator Lights ................................................................................................................................... 6

LAN ............................................................................................................................................... 6

Status LEDs .................................................................................................................................... 6

Installation .......................................................................................................................................... 7

Checking Correct Operation ................................................................................................................. 7

Understanding basic operation .............................................................................................................. 7

Modem Router Mode ....................................................................................................................... 7

Accessing the Internet Using the ETM350C/450C .................................................................................. 8

Setting Host PC’s Network Environment ........................................................................................... 8

Web Based Management Interface ........................................................................................................ 9

Setting Up a PC to Use the Web Based Management Interface ............................................................. 9

Saving Configurations Changes ......................................................................................................... 9

Connections Settings ...................................................................................................................... 10

WAN Settings .......................................................................................................................................... 11

LAN Settings ........................................................................................................................................... 13

DMZ Configuration ................................................................................................................................. 14

Port Forwarding ....................................................................................................................................... 14

IP Filter Settings ...................................................................................................................................... 15

Mac Filter Settings .................................................................................................................................. 16

Pinging ..................................................................................................................................................... 16

NTP Settings ............................................................................................................................................ 17

DDNS Settings ........................................................................................................................................ 18

Administrator Settings – Name and Password ........................................................................................ 19

Administrator Settings – Saving Configuration. ..................................................................................... 19

Administrator Settings -System Logs ...................................................................................................... 20

Administrator Settings - System .............................................................................................................. 21

Administrator Settings - Update .............................................................................................................. 21

Reboot .......................................................................................................................................... 22

SMS Commands for ETM350C/450C Router ....................................................................................... 23

ETM350C ETM450C User Manual 201405RV01.docx

Page 3 of 24

Introduction

For Support Contact +61-2-9956-7377


Nomenclature

The ETM350C (superseded, but included for reference) incorporates the Cinterion EU3-P engine and is intended for use in Asia, Australasia, and Europe (network and regulatory approvals permitting).

The ETM450C incorporates the Cinterion PH8-P engine and is intended for use in Asia,

Australasia, and Europe (network and regulatory approvals permitting).

Overview.

The ETM350C/450C is an industrial 3G Ethernet Router utilising the Cinterion EU3-P module to provide reliable always on wireless connection for M2M communications requirements.

Terminal Nomenclature/History

Model Comment

ETM350C Superseeded

Module Installed

EU3-P

Applications

Typical applications include:

◩

Communications link to concentrators/receivers for Metering

◩

Communications link to Programmable Logic Controllers (PLCs)

◩ Communications link for Security Systems

◩ Telemetry applications

◩

Backup communications




Specifications

Feature ETM350C

3G UMTS/HSDPA Frequency Bands 850/900/2100 MHz

2G GSM/GPRS Frequency Bands 900/1800 MHz

SIM Voltage

Supply Voltage

Power Consumption

Weight

Operating Temperature Range

1.8V & 3V

5 to 30VDC

ETM450C

850/900/1900/2100 MHz

850/900/1800/1900 MHz

1.8V & 3V

5 to 30VDC

600mA @ 12VDC 600mA @ 12VDC

260g 260g

-20°C to +60°C -20°C to +60°C

SIM Access via cover with screw on underside of unit

Default SIM position is SIM 1

SMA Antenna Connector, stub antenna supplied with unit

Ethernet

Connector

Product Drawing

RJ12 Power Connector

Ethernet Connector

RJ12 Power

Connector

124.0

106.5

SMA Antenna Connector

24.0

13.0

75.0

10.0

4.4

4.0

9.9

SIM Access

Fastening Screw on

Underside of Router

6 x Indicator LEDs




Power Supply

The ETM350C/450C power connection is a 6 pin RJ12 connector, pin allocations are shown below.

Pin

1

Function

Power Supply (+5 to +30VDC)

Looking at Router RJ12 Socket

1 2 3 4 5 6

6 GND

SIM Card

The SIM card slots are located on the underside of the ETM350C/450C Router. The unit supports both 3V and 1.8V SIMs. Any SIM card used needs to be correctly provisioned for the services and network upon which it is intended to be used.

Caution

Always disconnect power supply before inserting or removing SIM Card.

SIM Pin

If the SIM used has a PIN either;

• The unit can be configured to enter the SIM pin via the Web Based Management Interface.

OR

• The SIM PIN should be deactivated, insert the SIM in a mobile phone and deactivate the

SIM PIN then transfer the SIM into the router.




Indicator Lights

LAN

The ETM350C/450C can connect to a Host PC, HUB, Router etc using the embedded 10/100 LAN port. The RJ-45 connector (LAN port) has two Link-LEDs. The table below shows the each status of LAN connection.

LED

Green

State

ON

BLINK

Description

Indicates 10Mbps LAN connected.

Indicates data activity on 10Mbps LAN.

Orange

OFF

ON

BLINK

OFF

Indicates 10M LAN disconnected.

Indicates 100Mbps LAN connected.

Indicates data activity on 100Mbps LAN.

Indicates 100M LAN disconnected.

Status LEDs

The ETM350C/450C has 6-State LED for indicating the current status.

LED Display Description

Power

ON

OFF

Indicates that power is on

Indicates that power is off

Modem

Net

IP

SIM

RSSI

OFF Does not recognize the HSPA modem.

BLINK When there is data on the wireless mobile network

OFF When there is no data on the wireless mobile network

ON

OFF

ON

OFF

Mobile IP has been acquired from ISP

Mobile IP has not been acquired from ISP

The U-SIM card is ready

The U-SIM card is not ready

FLASHING 1 quick flash with 4 seconds off for low signal level

FLASHING 2 quick flash with 4 seconds off for medium level

FLASHING 3 quick flash with 4 seconds off for high level

FLASHING 4 quick flashes for 'excellent' signal

OFF Poor or no signal




Installation

The ETM350C/450C is a wireless mobile internet access device for connecting a PC or other LAN device to a cellular wireless service.

Please follow the steps below when you install this device.

• Insert U-SIM card. There are 2 positions for SIM1 and SIM2. Only 1 SIM is required, the second SIM is optional.

• Default position is SIM1.

• Connect an appropriate antenna.

• Connect the LAN cable between PC or LAN Device and the LAN port of the

ETM350C/450C.

• Connect the power adapter.

• Turn on the power switch (if fitted).

Checking Correct Operation

The ETM350C/450C connects by PPP (NAT Router) and the “Always on-line Mode” is the default state. When you get this device for the first time, please check whether the devices settings are appropriate for your application.

The following steps can be used to check the device is operating correctly.

1. Install ETM350C as above

Ensure the LAN cable is connected between the Device and the ETM350C/450C.

2. When power is applied, the Power LED should turn ON.

3. The Modem LED should turn ON within 20 seconds

4. The SIM LED should turn ON within 60 seconds

If the LED does not turn ON in 60 seconds, then check the SIM card and ensure it is inserted correctly

5. The NET LED should blink asynchronously whenever data is being transferred or received

6. The RSSI LED blinks when a signal is present

If RSSI LED is off, check the antenna connection and/or location and suitability

7. The IP LED turns ON when the unit has logged on the network and has acquired an IP address

Understanding basic operation

There are some basic operations of ETM350C/450C.

Modem Router Mode

In Modem router mode, and when the ETM350C/450C has an IP address, the ETM350C/450C shares the allocated IP with any connected Host devices via NAT. In this mode the

ETM350C/450C acquires its IP from the mobile network and the device connected to the

ETM350C/450C has a private IP allocated via DHCP from the ETM350C/450C.

There are two options for operation in Modem Router Mode, Always On-line and Demand On-line under Manual mode. For setting these options, refer to the [WAN] settings section.




Accessing the Internet Using the ETM350C/450C

By default the ETM350C/450C should be set to Modem Router Mode - Always On-line Mode.

Setting Host PC’s Network Environment

Assuming Windows XP, click “My Network Places” and then click the right mouse button and select

“properties”.

Select “Local Area Connection” then click the right mouse button and select “Properties”

Double click the “Internet Protocol [TCP/IP]” item.




Check the “Obtain an IP address automatically” then click the [OK] button.

Host PC’s setting is finished. Connect a LAN cable and a power cable on ETM350C/450C. Wait until the “IP” LED is on at which time you will be able to access the Internet.

Web Based Management Interface

Setting Up a PC to Use the Web Based Management Interface

You can configure the ETM350C/450C via the Web Based Management Interface. The steps required to set up the interface are;

1. Set Network environment as indicated in the previous section.

2. Connect the LAN and power cable to the ETM350C/450C.

3. Launch the web browser on your PC (such as Internet Explorer) then enter the following address, https://192.168.0.1/home.asp (Set by default). This router is designed for secure environments.

The pop-up window of the login page appears.

The default access settings are;

User name: admin

Password: admin

You can change these settings via the [System config] page -> [SYSTEM] menu.

When the correct information is entered the Web Management Interface will open.

Saving Configurations Changes

After making configuration changes you must click [Apply Changes] and reboot the

ETM350C/450C for the changes to take effect.




Connections Settings

After successfully logging in to the unit, you will see the Home page as below.

LAN:

Up Time:

IMEI:

The time period that the router has been on.

ID Number of router.

Area Information: Cell station router is connecting to.

PIN Status: SIM PIN status.

WAN:

As an example -65dbM is better than -80dbm.

Indicates whether the router is connected to a network or not.

If connected, it will show the IP address that the Network has assigned to this router, and the volume of data that has been upload/download during the current session.

IP address of this router within local network.


Page 11 of 24

WAN Settings



SIM slot:

APN Name:

Select either SIM1 or SIM2.

Depends on the service provider used. For example, in Australia, Telstra has following different APN names. Please choose correct one for your service. Default is “internet”

Username:

Password:

Authentication:

Username for your account if required.

Password for your account if required.

Select PAP or CHAP or both. Default is PAP & CHAP.

The unit (version1.0.38 firmware or above) supports Dual-SIM failover thereby providing redundancy when two SIM cards are used. This feature allows for automatic failover to a secondary service should the primary service become unavailable due to a signal problem, incorrect programming or failure of the SIM.




Auto PIN: To choose from Disable or enable. If you choose enable, Router will enter

PIN code automatically each time router is power on.

Keep your PIN code in safe place. If it fails 3 times, the SIM card will be blocked. You will then need to ask your service provider to give you the PUK code to unlock the SIM.

For nd

SIM is provided by different Operator, then the settings may be different.

Check LAN Cable: If this option is enabled then the unit will disconnect the modem from the carrier whenever the LAN cable is disconnected or the connected device is inactive.

Band:

Periodic Reset:

Set to Auto or choose appropriate bands. Default is Auto.

Router will be reset according to preset timer. Value is from 1-24 hours.

The default is Disable.


Page 13 of 24

Keep Alive:



This is to make sure that router is on-line all the time. If enable is chosen, the router will ping the nominated IP address with interval time and IP set by user on 1

st

or 2

nd

or both server. The ‘ping fail’ count is incremented only if all configured servers fail to respond. If the count reaches the preset value then the router will be reset and re-connect again.

LAN Settings

IP Address:

Subnet Mask: the static IP address shown on “IP address”. If DHCP Client is chosen, the

Router IP address will be assigned by connecting host. Default is Static.

To assign IP address for Router. Default is 192.168.0.1

Default is 255.255.255.0

DHCP Client Range: This is the range that Router will assign IP address to devices which connect to this router. Default is 192.168.0.200-192.168.0.250

1

2 st nd

DNS:

DNS:

DNS address. Default is 168.126.63.1

DNS address. Default is 168.126.63.2

Assign IP by MAC: Allows specific MAC addresses to be assigned to specific IP addresses

When you have finished these settings, you must click on the [Apply change] button.




DMZ Configuration

If DMZ is Enabled, please enter DMZ Host IP address. Default is disabled.

Port Forwarding

If Port Forwarding is enabled, a user can connect to devices via the Router.

For example, there are 2 pieces of IP camera, Camera A with IP address 192.168.0.11 with port 80

(preset inside of camera) and Camera B with IP address 192.168.0.10 also with port 80.

IP address:

Protocol:

Port Range:

Apply Changes:

Type in device IP address.

To choose from TCP, UDP or both.

To enter port number or range.

After Apply Changes is clicked, the setting will be added to Current Port

Forwarding Table. (after applying changes reboot the router and confirm

correct settings once reboot complete)

Note, for firmware versions 1.1.10 and later it is possible to have multiple devices with the same destination port on different IP addresses on the LAN (a suitable switch is required) as long as the destination port on the WAN is not the same ( refer to example above ).

Note for firmware versions prior to 1.1.10, multiple IP addresses with the same destination port on the LAN are not supported. In addition the port range must increment by at least 1, ie to use a LAN port of 80 set the range as 80 to 81.




IP Filter Settings

IP filtering is used to block un-wanted users either from local or remote side.

Out-bound IP

Filtering:

Enable this function will block all registered IP address on Local network.

In-Bound IP

Filtering:

Rule:

Protocol:

Port Range:

Enable this function will block all unregistered IP address to send in packet.

Only registered IP address can send in packet under rule’s restriction.

If Rule is click, the IP address can send it packet.

It can define to allow TCP, UDP or both to communicate.

It specifies port number or range to accept.




Mac Filter Settings

Mac Filtering is used to block all un-wanted users if their equipment’s Mac address is not registered.

If Mac Filtering is enabled, please enter Mac address and apply changes. Only registered Mac addresses can access this router.

Pinging

Enter IP address and click [Run], Router will ping this IP address and show result.


Page 17 of 24

NTP Settings

This is to synchronize router timer with public time server.

Enable NTP

client update

Time zone:

Daylight saving: will synchronize to public time server.

Select which time zone to use.

Click if Daylight saving is in use.






DDNS Settings

In most of cases, the Network Operator will assign a Dynamic IP address to Router upon connection. To avoid tracing IP, the Router can link to DDNS service. For example, if you have applied for a service from www.dyndns.com and the registered address is 350C.dyndns.com. Then every time when Router powers on, it will register to www.dyndns.com. All you need is to type-in

350C.dyndns.com to login this router.

When DDNS is enabled:

Domain name: Enter the name has been applied.

Username/E-mail: Enter user name or e-mail. This depends on your DDNS service requirement. If it needs e-mail to login, then type-in e-mail address only.

Password/key: Enter password or key.


Page 19 of 24

Administrator Settings – Name and Password

Allows you to change the name and password for the Router.



Administrator Settings – Saving Configuration.

Save:

Load settings

from File:

Select Save to save current setting as a file.

Point to file location, click upload to load settings which have previously been saved




Administrator Settings -System Logs

Enable log:

Enable Remote

Logs:

Log file will shows on log screen.

Log file will send to the remote address which shows on Log Server IP

Address.




Administrator Settings - System

This section is to setup Router system.

Web Access: Enable web access. When user needs to login Web address should be

Telnet Access: https://192.168.0.1/home.asp

If Telnet Access is enabled, please specify which port is used

NAT: for Telnet. Default is port 23.

Default is NAT router.

SMS Phone Number: If the router receives an SMS “REBOOT” message from any registered phone number it will cause the router to reboot. 3 different cellular phone numbers can be registered.

Administrator Settings - Update

Contact ETM should a firmware upgrade be required.


Page 22 of 24

Reboot

Reboot:



When Reboot is clicked, it will pop up a dialog box for Save current

setting and reboot. Click OK, and the router will save settings and reboot.




SMS Commands for ETM350C/450C Router

SMS Command

DSR.REBOOT

DSR.NETINFO

DSR.SIM=X

Action

When received by the router the unit will respond via

SMS then reboot

Unit will respond with network status, IP address

Set SIM slot to 1 or 2, where

X=1 or 2

Typical Response

Router will reboot now.

Please wait….

SIM:1, IP:58.104.69.177,

APN:internet, ID:user,

PW:password, Auth:PAP and

CHAP, Sig:15

If X is already active then it responds:

SIM X OK

If not the unit responds: SIM

X Switched

SIM X settings have been changed

DSR.SIM=X,APN,ID,PASSWORD,

Authentication,Dialup Number

Changes and sets SIM slot and applicable ISP dialup settings

Note:

1. Above SMS commands are case sensitive and your phone number must be in the units phone book


ETM Pacific Pty Ltd

Suite 6, 273 Alfred Street

North Sydney NSW 2060

Australia

Tel: +61 (0)2 9956 7377

Fax: +61 (0)2 9956 5791

Email: [email protected]

Web: www.etmpacific.com.au

ETM Matteknik AB

Ekbacksvägen 32

SE-168 69 Bromma

Sweden

Tel: +46 (0)8 25 28 75

Fax: +46 (0)8 80 11 10

Email:

Web: [email protected]

www.etm.se

© ETM Pacific Pty Ltd · Subject to change without notice.

ETM350C ETM450C User Manual 201405RV01

3G Industrial Ethernet Router

Features:

Contents

Introduction

Nomenclature

Overview.

Applications

Specifications

Product Drawing

Power Supply

SIM Card

SIM Pin

Indicator Lights

LAN

Status LEDs

Installation

Checking Correct Operation

Understanding basic operation

Modem Router Mode

Accessing the Internet Using the ETM350C/450C

Setting Host PC’s Network Environment

Web Based Management Interface

Setting Up a PC to Use the Web Based Management Interface

Saving Configurations Changes

Connections Settings

WAN Settings

LAN Settings

DMZ Configuration

Port Forwarding

IP Filter Settings

Mac Filter Settings

Pinging

NTP Settings

DDNS Settings

Administrator Settings – Name and Password

Administrator Settings – Saving Configuration.

Administrator Settings -System Logs

Administrator Settings - System

Administrator Settings - Update

Reboot

SMS Commands for ETM350C/450C Router

Related manuals

ETM

ETM450C

ETM

DeltaBlue

ETM

ETM9140-1

ETM

ETM8120-4

ETM

ETM9420-1

ETM

ETM770-4