advertisement
Black plate (4,1)
Prologue
Foreword
INFINITI NAVIGATION SYSTEM
HELPDESK CONTACT INFORMATION
For assistance or inquiries about the
INFINITI Navigation System, or to order updated map data, contact the INFINITI
NAVIGATION SYSTEM HELPDESK at:
. ADDRESS: P.O. Box 1588 Orem, UT
84059-992
. E-MAIL: [email protected]
. WEB SITE: www.InfinitiNavigation.com
or www.infiniti.ca.
. PHONES: 1-800-777-0325
. HOURS: 6:00 AM to 5:00 PM (Pacific
Time)
INFINITI CONSUMER AFFAIRS DE-
PARTMENT
For assistance or inquiries about the
INFINITI warranty, service or general questions, contact the INFINITI Consumer Affairs
Department at:
For U.S. customers
1-800-662-6200
For Canadian customers
1-800-361-4792
FOREWORD
Thank you for purchasing an INFINITI vehicle.
This user’s manual is for the navigation system only. This manual contains operating instructions for the INFINITI Navigation
System offered in your INFINITI vehicle.
Please read this manual carefully to ensure safe operation of the navigation system.
. Because of possible specification changes and optional equipment, sections of this manual may not apply to your vehicle.
. All information, specifications and illustrations in this manual are those in effect at the time of printing. INFINITI reserves the right to change specifications or design at any time without notice.
. Do not remove this manual from the vehicle when selling this vehicle. The next user of this navigation system may need the manual.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (1,1)
Table of Contents
1 Introduction
3 Map settings
6 Storing location/route
2 Getting started
4 Setting destination
Transferring information to/from
................................. 6-22
7
.......................... 2-11
................................. 2-16
5 Route guidance
........................... 5-2
................................... 7-3
Viewing information about current
.............................. 7-15
.......................... 7-16
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (2,1)
.......................... 7-31
8 Other settings
10
.......................... 10-2
11 Troubleshooting guide
9 Voice recognition
.............................. 11-6
............................ 9-24
............................. 11-9
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
1 Introduction
Black plate (5,1)
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (6,1)
1. Introduction
HOW TO USE THIS MANUAL
This manual uses special words, symbols and icons that are organized by function.
Please refer to the following items to understand how to use this manual properly.
FOR SAFE OPERATION
WARNING!
GUID-05735A11-D9EA-4B38-ACB8-655447DB12A0
Indicates the presence of a hazard that could cause death or serious personal injury. To avoid or reduce the risk, the procedures must be followed precisely.
CAUTION!
GUID-2F458E6B-513D-4954-B242-9422F5A19DF9
Indicates the presence of a hazard that could cause minor or moderate personal injury or damage to your vehicle. To avoid or reduce the risk, the procedures must be followed carefully.
NOTE:
Indicates items that help you understand and maximize the performance of your vehicle. If ignored, they may lead to a malfunction or poor performance.
REFERENCE SYMBOLS
INFO:
Indicates information that is necessary for efficient use of your vehicle or accessories.
Reference page:
Indicates the title and page that you should refer to.
<>:
Indicates a button on the control panel and steering wheel.
[ ]:
Indicates a key/item displayed on the screen.
Voice Command:
Indicates an operation by voice command.
Variable commands, such as numbers, are indicated in
italics
in angle brackets < >.
SAFETY INFORMATION
This system is primarily designed to help you reach your destination, and it also performs other functions as outlined in this manual. However, you, the driver, must use the system safely and properly. Information concerning road conditions, traffic signs and the availability of services may not always be up to date. The system is not a substitute for safe, proper and legal driving.
Before using the navigation system, please read the following safety information. Always use the system as outlined in this manual.
WARNING!
GUID-43837604-6D3B-4A88-95CC-9A1143515BA5
.
To operate the navigation system or use the INFINITI controller, first park the vehicle in a safe location and set the parking brake. Operating the system while driving can distract the driver and may result in a serious accident.
.
Do not rely on route guidance alone.
Always be sure that all driving maneuvers are legal and safe in order to avoid accidents.
1-2
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (7,1)
1. Introduction
.
Do not disassemble or modify this system. If you do, it may result in accidents, fire or electrical shock.
.
If you notice any foreign objects in the system hardware, spill liquid on the system or notice smoke or a smell coming from it, stop using the system immediately and contact an INFINITI retailer. Ignoring such conditions may lead to accidents, fire or electrical shock.
CAUTION!
GUID-CABB1B9E-B526-42ED-BC3A-AF6F2878701B
.
Do not use this system if you notice any malfunctions such as a frozen screen or the lack of sound. Continued use of the system may result in accidents, fire or electrical shock.
.
Some states/provinces may have laws limiting the use of video screens while driving. Use this system only where it is legal to do so.
.
Extreme temperature conditions [below
−48F (−208C) and above 1588F (708C)] could affect the performance of the system.
.
The glass display screen may break if it is hit with a hard or sharp object. If the glass screen breaks, do not touch it.
Doing so could result in an injury.
NOTE:
Do not keep the navigation system running with the engine or the hybrid system stopped. Doing so may discharge the vehicle battery (12V battery). When you use the navigation system, always keep the engine or the hybrid system running.
LASER PRODUCT
This navigation system is certified as a
Class 1 laser product.
The navigation system complies with DHHS
Rules 21 CFR Chapter 1, Subchapter J.
WARNING!
GUID-BC8CBF71-329B-435A-9D1F-27E1D038026E
.
Do not disassemble or modify this system. There are no user serviceable parts in this navigation system.
.
If maintenance, adjustments and operations other than those specified in this manual are attempted, injury due to laser radiation and exposure could occur.
JI0221
Required SiriusXM Satellite Radio and
NavTraffic monthly subscriptions are sold separately. NavTraffic are only available in select markets. For more information, see www.siriusxm.com/navtraffic.
1-3
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (8,1)
1. Introduction
JI0222
Required SiriusXM Satellite Radio and
NavWeatherXM monthly subscriptions are sold separately. NavWeatherXM is only available in select markets. For more information, see www.siriusxm.com/navweather.
1-4
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (9,1)
2 Getting started
Character (letters and numbers)
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (10,1)
2. Getting started
CONTROL BUTTONS AND FUNCTIONS
Designs and button layout may vary depending on the specifications and the model.
CONTROL PANEL (Type A)
2-2
<DEST>
Push to enter a destination. Various methods for entering a destination are available.
“4. Setting destination”
Condition: Language=NAM_English/
JNB0275X
<ROUTE>:
Push to access the guidance control functions (guidance cancellation, route priority, waypoint setting on the route, etc.).
“5. Route guidance”
INFINITI controller:
Turn to highlight an item on the screen, and push <ENTER> to select the highlighted item.
On the map screen, turn to adjust the map scale.
To scroll the map, push the controller in the direction you want to scroll.
“INFINITI controller” (page 2-6)
<INFO>:
Push to display the vehicle, traffic, weather or voice recognition information.
“7. Viewing technical information”
<STATUS>:
Push multiple times to display audio information with either the air conditioner status, fuel economy or navigation directions.
<DAY/NIGHT OFF >:
Push to switch between the day screen
(bright) and the night screen (dark).
Push and hold to turn off the display.
Push again to turn on the display.
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (11,1)
2. Getting started
<ZOOM IN>, <ZOOM OUT>:
Push to adjust the map scale.
<MAP>:
Push to display the map. While following a programmed route, push multiple times to change the type of route information displayed.
<BACK>:
Push to return to the previous screen.
In a settings screen, this button is also used to apply the setting.
In a character input screen, this button is also used to delete the characters that have been entered.
<VOICE>:
Push to hear the current guidance for a programmed route.
<SETTING>:
Push to access the system settings.
“8. Other settings”
INFO:
. If <BACK> needs to be pushed to apply the setting on a settings screen, this manual will explicitly include a step for this procedure. Otherwise, pushing <BACK> returns the display to the previous screen.
. The layout of the control panel switches may vary depending on the vehicle model and equipment.
CONTROL PANEL (Type B)
<DISP> (without Around View Monitor):
Push to access the display settings.
<CAMERA> (with Around View Moni-
tor):
Push to operate the Around View
Monitor.
Condition: Language=NAM_English/
IGT0203
<DEST>:
Push to enter a destination. Various methods for entering a destination are available.
“4. Setting destination”
2-3
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (12,1)
2. Getting started
2-4
INFINITI controller:
Slide or rotate to highlight an item on the screen, and push <ENTER> to select the highlighted item.
On the map screen, turn to adjust the map scale.
To scroll the map, slide the controller in the direction you want to scroll.
“INFINITI controller” (page 2-6)
<INFO>:
Push to display the vehicle, traffic, weather or voice recognition information.
“7. Viewing technical information”
<SETTING>:
Push to access the system settings.
“8. Other settings”
<ROUTE>:
Push to access the guidance control functions (guidance cancellation, route priority, waypoint setting on the route, etc.).
“5. Route guidance”
<MAP>:
Push to display the map. While following a programmed route, push multi-
Condition: Language=NAM_English/ ple times to change the type of route information displayed.
<BACK>:
Push to return to the previous screen.
In a settings screen, this button is also used to apply the setting.
In a character input screen, this button is also used to delete the characters that have been entered.
<VOICE>:
Push to hear the current guidance for a programmed route.
<STATUS>:
Push multiple times to display audio information with either the air conditioner status, fuel economy or navigation directions.
<DAY/NIGHT OFF >:
Push to switch between the day screen
(bright) and the night screen (dark).
Push and hold to turn off the display.
Push again to turn on the display.
INFO:
. If <BACK> needs to be pushed to apply the setting on a settings screen, this manual will explicitly include a step for this procedure. Otherwise, pushing <BACK> returns the display to the previous screen.
. The layout of the control panel switches may vary depending on the vehicle model and equipment.
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (13,1)
CONTROL PANEL (Type C)
<DEST>:
Push to enter a destination. Various methods for entering a destination are available.
“4. Setting destination”
INFINITI controller:
Slide or rotate to highlight an item on the screen, and push <ENTER> to select the highlighted item.
On the map screen, turn to adjust the map scale.
Condition: Language=NAM_English/
IGT0228
To scroll the map, slide the INFINITI controller in the direction you want to scroll.
“INFINITI controller” (page 2-6)
<INFO>:
Push to display the vehicle, traffic, weather or voice recognition information.
“7. Viewing technical information”
2. Getting started
<SETTING>:
Push to access the system settings.
“8. Other settings”
<ROUTE>:
Push to access the guidance control functions (guidance cancellation, route priority, waypoint setting on the route, etc.).
“5. Route guidance”
<MAP>:
Push to display the map. While following a programmed route, push multiple times to change the type of route information displayed.
<BACK>:
Push to return to the previous screen.
In a settings screen, this button is also used to apply the setting.
In a character input screen, this button is also used to delete the characters that have been entered.
<VOICE>:
Push to hear the current guidance for a programmed route.
<STATUS>:
Push multiple times to display audio information with either the air condi-
2-5
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (14,1)
2. Getting started tioner status, fuel economy or navigation directions.
<DAY/NIGHT OFF >:
Push to switch between the day screen
(bright) and the night screen (dark).
Push and hold to turn off the display.
Push again to turn on the display.
INFINITI CONTROLLER
With Directional buttons
INFO:
. If <BACK> needs to be pushed to apply the setting on a settings screen, this manual will explicitly include a step for this procedure. Otherwise, pushing <BACK> returns the display to the previous screen.
. The layout of the control panel switches may vary depending on the vehicle model and equipment.
IGT0076
<ENTER>:
Push to select the highlighted item on the screen.
If this button is pushed while a map is displayed, the map menu screen is displayed.
Main directional buttons:
Use to move across the map, highlight an item on the screen or adjust a setting (volume, brightness, etc.).
Additional directional buttons:
Use to move across the map or highlight an item on the character input screen.
2-6
Center dial:
Turn to highlight an item on the screen or adjust a setting.
The center dial can also be used to adjust the map scale.
Without Directional buttons
IGT0235
<ENTER>:
Push to select the highlighted item on the screen.
If this button is pushed while a map is displayed, the map menu screen is displayed.
Center dial/Slide switch:
Center dial
Turn to highlight an item on the screen or adjust a setting.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
The center dial can also be used to adjust the map scale.
Slide switch
Slide (push upward/downward/leftward/rightward) to select an item on the screen or to adjust a setting
(volume, brightness, etc.).
The map can be scrolled in 8 directions by sliding this switch.
STEERING WHEEL SWITCHES
Type B JNB0192X
Black plate (15,1)
2. Getting started
Type D JNB0194X
Type A JNB0191X
Condition: Language=NAM_English/
Type C JNB0193X Type E JNB0287X
<ENTER>:
Tilt to highlight an item on the screen or adjust a setting. Push to select the highlighted item.
If this button is pushed while a map is displayed, the map menu screen is
2-7
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (16,1)
2. Getting started
2-8 displayed.
“Map menu screen” (page 2-18)
Push and hold while a map or status screen is shown to display the Start
Menu.
“Start menu” (page 2-13)
If this button is tilted up while the audio function is activated and the map or status screen is displayed, the audio system can be operated.
<− +>:
Use to adjust the volume. These buttons have the same function as that of the volume control knob. Refer to the vehicle Owner’s Manual.
<BACK >:
Push this button during a setting operation to return to the previous screen. In a settings screen, this button can also be used to apply the setting.
<TALK >:
Push to start the voice recognition system. If the voice recognition system is already activated, pushing this button cancels the voice guidance and a voice command can be spoken
Condition: Language=NAM_English/ immediately.
<SOURCE>:
Use to switch the audio mode (source).
Refer to the vehicle Owner’s Manual.
< >:
Push to display the phone mode screen.
Refer to the vehicle Owner’s Manual.
< >:
Push to change what is shown on the vehicle information display.
Refer to the vehicle Owner’s Manual.
STARTING SYSTEM
The navigation system starts when the ignition switch is turned to the ACC or ON position.
NOTE:
Do not keep the navigation system on with the engine or the hybrid system stopped. Doing so may discharge the vehicle battery (12V battery). When you use the navigation system, always keep the engine or the hybrid system running.
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (17,1)
2. Getting started
NAVIGATION SYSTEM STATUS SCREEN
By pushing <STATUS> at any time, a split screen with audio information that is always at the top can be displayed.
Each time <STATUS> is pushed, the bottom part of the screen changes between air conditioner, fuel economy and navigation directions.
INFO:
There are different status screens displayed depending on various factors, such as the currently active mode, whether a destination has been set or not, etc.
above appears.
Turning direction at the next intersection
Name of the next street
Distance to the next intersection
Distance remaining to the destination
Remaining time to the destination
JNB0196M
When a route to the destination is not set and the audio system is off, a screen similar to the one above appears.
JNB0195M
When a route to the destination is set and the audio system is on, a screen similar to the one
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
2-9
2. Getting started
FUNCTIONS DISABLED WHILE DRIVING
2-10
Condition: Language=NAM_English/
Black plate (18,1)
IGT0081
To ensure safe driving, some functions cannot be operated or have limited operation when the vehicle driving speed is above 5 MPH (8 km/h).
The on-screen text and keys for these restricted functions will be "grayed-out" or muted and cannot be selected while driving. In some cases, a screen message will appear indicating a restricted function.
Restricted functions while driving include:
. Character (letter and number) input screen during destination entry (street address, phone number, freeway entrance/exit, intersection, city center)
. Places search by name and city name
. Scrolling and viewing of certain navigation lists
. Adding/editing address book entries
. Adding/editing home location
. Storing current position, information, destinations
These functions will become available again when the vehicle speed is reduced to 5 MPH (8 km/h).
Destination functions available while driving include:
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
. Home
. Address Book
. Previous Destinations
. Nearby places
. My places
. Map input
TOUCH SCREEN OPERATION
The same operations described for the scrolling dial are possible using touch screen operation.
MENU SCREEN AND OPERATION METHOD
MENU SCREENS AND THEIR PURPOSES
Black plate (19,1)
2. Getting started
Condition: Language=NAM_English/
Push <DEST>, <ROUTE>, <INFO> or
<SETTING> to display the corresponding menu screen.
How to select menu item
Example: <DEST> screen
1. Highlight the preferred menu item using the INFINITI controller.
IGT0231
2. To select the highlighted menu item, push <ENTER>. The next screen is displayed.
3. Push <BACK> to return to the previous screen.
Push <MAP> to return to the current location map screen.
2-11
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (20,1)
2. Getting started
INFO:
An item can also be selected by tilting <ENTER> on the steering wheel up and down, and then pushing <ENTER>.
USING CONTROLS TO ADJUST VALUES, LEVELS, ETC.
2-12
Condition: Language=NAM_English/
With directional buttons
IGT0083
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (21,1)
2. Getting started
. These same adjustments can also be performed using the touch panel operation.
“Adjusting volume and others”
(page 2-15)
START MENU
The start menu can be displayed using the switches on the steering wheel.
IGT0232
Without directional buttons
There are five main methods to control the navigation system: the center dial, the main directional buttons, the slide switch, the touch panel and the switches on the steering wheel. Use these controls to adjust the volume of the phone and voice guidance, the display brightness, etc.
2. Adjust the value or level indicating bar using the INFINITI controller.
3. Push <ENTER> or <BACK> to apply the setting.
INFO:
How to adjust
1. Highlight the preferred setting item and push <ENTER>. The color of the corresponding adjustment item changes.
. The volume of phone and voice guidance, the display brightness, etc. can be adjusted by tilting <ENTER> on the steering wheel up and down.
IGT0084
1. Push and hold <ENTER> on the steering wheel.
2. Highlight the preferred item and push
<ENTER>.
INFO:
<ENTER> on the steering wheel can be used to display the start menu only when the map or status screen is displayed.
2-13
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (22,1)
2. Getting started
Available setting items
. [Destination]:
Displays the destination screen. It is the same screen that appears when
<DEST> is pushed.
“4. Setting destination”
. [Route]:
Displays the route screen. It is the same screen that appears when
<ROUTE> is pushed.
“5. Route guidance”
. [Info]:
Displays the information screen. It is the same screen that appears when
<INFO> is pushed.
“7. Viewing technical information”
. [Settings]:
Displays the settings screen. It is the same screen that appears when
<SETTING> is pushed.
“8. Other settings”
LIST SCREEN
After searching for a point of interest, a list screen is displayed.
Depending on the list displayed, it can be sorted.
Items displayed in list
Highlight the preferred item from the list and push <ENTER> to select it. If a location or facility name is not completely displayed (due to length), highlight the item to display the hidden
2-14
Condition: Language=NAM_English/
IGT0085 part of the name.
Distance from the current location
Direction to the point of interest
If the entire list cannot be displayed on the screen, the system displays the total number of items in the list and the entry number of the selected item.
Scroll the list using the INFINITI controller.
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (23,1)
2. Getting started
The list will automatically scroll to the section of the list that begins with the letter selected.
INFO:
This feature is only available when the list is sorted by name and is not active for all lists.
Highlight and push <ENTER> to select the other sort options.
When the list is sorted by the shortest distance, the selected location can be confirmed in the preview displayed on the right side of the screen.
Highlight and push <ENTER> to modify the search conditions.
TOUCH PANEL OPERATION
With this system, it is possible to use the
INFINITI controller and touch panel operation to perform the same operations.
This manual describes the operations using the INFINITI controller.
For the operations that differ from those of the INFINITI controller and for useful methods for using the touch panel operation, refer to each section.
EXAMPLE OF TOUCH PANEL OPERA-
TION
Examples of operations performed using the touch panel operation are described here.
Selecting item
Adjusting volume and others
IGT0087
Touch [+] or [−] located on the right and left of the bar graph to perform the adjustment.
Scrolling a list or message
Condition: Language=NAM_English/
IGT0086
When the item is touched, the next screen is displayed.
IGT0088
Touch [ ] or [ ] to scroll the list or message.
Touch [ ] or [ ] to skip to the next page.
2-15
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (24,1)
2. Getting started
Inputting letters and numbers HOW TO INPUT LETTERS AND NUMBERS
CHARACTER (letters and numbers)
INPUT SCREEN
Alphanumeric characters are entered to set a destination, search for a facility, edit stored locations, etc.
INFO:
Inputting letters can also be done with the touch panel operation.
IGT0089
1. Touch the letter or number.
2. Touch [Delete] to delete a character.
Push and hold [Delete] to delete all of the characters.
IGT0090
1. Use the INFINITI controller to highlight a character on the displayed keyboard.
IGT0092
3. Push <BACK>, or highlight [Delete] and push <ENTER> to delete the last character entered.
Push and hold <BACK> to delete all the characters entered.
Highlight [Space] and push <ENTER> to enter a space.
2-16
Condition: Language=NAM_English/
IGT0091
2. Push <ENTER>. The highlighted character is entered.
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
IGT0093
Black plate (25,1)
2. Getting started
4. After finishing the entry, highlight [List] and push <ENTER>.
INFO:
. Push <BACK> on the control panel to return to the previous screen, but only after deleting all the characters entered.
. Touch [BACK] on the screen to return to the previous screen even when characters have been entered.
. The list screen appears automatically when text has been entered and the matching list items have been narrowed down to a number that will fit on the screen.
NUMBER INPUT SCREEN
A phone number or a street number can also be entered as a search method to look for a destination. Perform the following procedure to enter a number.
INFO:
Only the locations included in the map data database can be searched for by a phone number.
IGT0096
2. Push <ENTER>. The highlighted number is entered.
INFO:
Inputting numbers can also be done with the touch panel operation.
Symbol input screen IGT0094
. Symbol keys are displayed by highlighting
[Symbols] and pushing <ENTER>. Alphabet keys are displayed by highlighting [A-Z] and pushing <ENTER>.
Condition: Language=NAM_English/
IGT0095
1. Use the INFINITI controller to highlight a number on the displayed keyboard.
IGT0097
3. Push <BACK>, or highlight [Delete] and push <ENTER> to delete the last number entered.
Push and hold <BACK> to delete all the numbers entered.
2-17
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (26,1)
2. Getting started
IGT0098
4. After finishing the entry, highlight [List] and push <ENTER>.
INFO:
. Push <BACK> on the control panel to return to the previous screen, but only after deleting all the numbers entered.
. Touch [BACK] on the screen to return to the previous screen even when numbers have been entered.
MAP MENU SCREEN
Push <ENTER> while the current location map screen or a scrolled map screen is displayed to display the menu corresponding to that screen.
This menu can be used to access helpful functions quickly, such as setting a destination and searching for points of interest nearby.
There are various methods used to select a menu item. Use a method described earlier in this manual.
“Menu screen and operation method”
(page 2-11)
INFO:
With the touch panel operation, the same screen can be displayed by touching [Map
Menu] located on the map screen.
CURRENT LOCATION MAP SCREEN
IGT0099
If <ENTER> is pushed while the current location map screen is displayed, the following options are available.
. [Store Location]:
Stores the current vehicle location in the Address Book. The stored location can be retrieved as necessary to set it as a destination (waypoint).
“Storing location” (page 6-2)
. [Nearby Places]:
Searches for points of interest near the current vehicle location, such as restaurants and gas stations, etc.
“Finding nearby place” (page 4-6)
. [Map View]:
Performs map operations such as the switching of map type and the setting of map orientation and scale.
2-18
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (27,1)
2. Getting started
“3. Map settings”
. [Map Icons]:
Displays map icons of certain points of interest (such as restaurants and gas stations, etc.) on the map around the current vehicle location.
“Displaying map icons”
(page 3-18)
. [Store Tracking]:
Stores in the Address Book the route travelled from the starting point to the current location.
“Storing tracked route” (page 6-6)
SCROLLED LOCATION MAP SCREEN
IGT0100
If <ENTER> is pushed while a scrolled map screen is displayed, the following options are available.
. [New Dest.]:
Sets the destination to the map location where <ENTER> was pushed. If a destination is already set, the location will be set as the new destination.
“Setting point on map”
(page 4-23)
. [Add to Route]:
Sets the map location where <ENTER> was pushed as the destination or a waypoint. This is available only when a suggested route is already set.
“Setting destination or waypoint”
(page 5-15)
. [Nearby Places]:
Searches for points of interest near the map location where <ENTER> was pushed and sets them as a destination or waypoint.
Use the same search method as the one for [Places].
“Finding nearby place” (page 4-6)
. [Store Location]:
Store the map location where <ENTER> was pushed in the Address Book. The stored location can be retrieved to set it as a destination or waypoint.
“Storing location” (page 6-2)
. [Delete]:
Deletes a stored location. Available only when the cross pointer is placed over a stored location icon.
. [Incident Detail]:
This function can be selected only when the traffic information icon is displayed. Displays the details of the traffic information icon. Place the cross pointer over the icon to be checked.
INFO:
Incident details are a feature of Traffic Information, and a NavTraffic subscription is required in order to receive Traffic Information.
2-19
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (28,1)
2. Getting started
STORING HOME LOCATION/ADDRESS
HOW TO STORE HOME LOCATION
If a home location is already stored in the
Address Book, it can be easily retrieved to set the route to the stored home location.
The procedure to store the home location is the same as for storing any other location.
“4. Setting destination”
As an example, the procedure for storing the home location by searching for a destination by address is described here.
IGT0102
3. A confirmation message is displayed.
Confirm the message, highlight [Yes] and push <ENTER>.
IGT0104
5. Enter the address of the home location, highlight [OK] and push <ENTER>.
“Finding address” (page 4-4)
The map screen is displayed.
IGT0101
1. Push <DEST>.
2. Highlight [Home (Add New)] and push
<ENTER>.
IGT0103
4. Highlight [Street Address] and push
<ENTER>. A character input screen is displayed.
IGT0105
6. Adjust the location of your home using the INFINITI controller, if necessary.
7. After adjusting the location, push
<ENTER>.
2-20
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (29,1)
2. Getting started
INFO:
It is recommended to move the home location for security reasons.
INFO:
The same setting can also be performed by pushing <SETTING> and highlighting [Navigation].
“Storing location by searching” (page 6-2)
SETTING DESTINATION
SEARCHING FOR DESTINATIONS
As an example, the method for setting a nearby restaurant as the destination using
[Places] is described here.
IGT0106
8. A message is displayed and the home location is stored.
JNB0289X
1. Push <DEST>.
2. Highlight [Places] and push <ENTER>.
9. Highlight [OK] and push <ENTER>.
IGT0107
10. Push <MAP> to return to the current location map screen. The home icon is displayed on the map.
Condition: Language=NAM_English/
IGT0109
3. Highlight [Nearby RESTAURANT] and push <ENTER>.
2-21
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (30,1)
2. Getting started
INFO:
The search can also be narrowed down by selecting [All Categories or Name] or [ZAGAT] on this screen. By selecting [All Categories or Name], the area, name of facility, etc. can be specified. By selecting [ZAGAT], restaurants registered in the ZAGAT database can be searched and sorted by their rating regarding food, decor, cost, service, etc.
The Zagat Content displayed may not reflect the most up-to-date Zagat Content available to the public.
.
If there is a route already in progress, only places along the current route will be listed. Turn off [Show Along Route] at the top of list to display all nearby places.
STARTING ROUTE GUIDANCE
After the destination is set and route calculation is performed, the suggested route is displayed.
IGT0110
4. Highlight the preferred restaurant from the list and push <ENTER>.
.
INFO:
The position of the selected location is displayed in the preview on the right side of the screen.
IGT0111
5. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination, and push <ENTER>.
The system sets the destination to the selected location and starts calculating a route.
INFO:
Even after setting a destination, the location of the destination can be adjusted and the route can be stored, etc., if necessary.
“Procedures after setting destination”
(page 5-2)
IGT0112
1. Highlight [Start] and push <ENTER>.
IGT0113
2. Once route guidance is started, the system navigates you through the guide points using visual and voice guidance.
2-22
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (31,1)
2. Getting started
CANCELING ROUTE
Cancel a route that is already set according to the following procedure.
IGT0114
3. When approaching a guide point, the system automatically changes to the split screen and shows an enlarged view of the intersection in the left screen. Push <MAP> to switch to the full map screen.
IGT0116
1. Push <ROUTE>.
2. Highlight [Cancel Route] and push
<ENTER>.
INFO:
. If a route is canceled, [Cancel Route] changes to [Resume Route].
Highlight [Resume Route] and push <ENTER> to reactivate the canceled route.
This is available only until a new route is set or a currently set destination is deleted.
. [Cancel Route] does not delete the destination that has been set. To delete a destination, push <DEST> and highlight [Next Page] and push <ENTER>. And then highlight
[Delete Destination] and push <ENTER>.
“Delete destination” (page 4-24)
IGT0115
4. When arriving at the destination, route guidance automatically ends.
IGT0117
3. A confirmation message is displayed.
Highlight [Yes] and push <ENTER>.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
2-23
Black plate (32,1)
2. Getting started
OPERATING MAPS
HOW TO VIEW MAP SCREEN
The navigation system displays various information on the map screen.
Screen information
Vehicle icon:
Indicates the current vehicle location and the direction of travel.
JNB0290X
Starting point:
Displays the vehicle location, with which the route is set, as the starting point.
2-24
Condition: Language=NAM_English/
Guide point:
Indicates a guide point on the route.
Waypoint:
Displays the set locations between the starting point and the destination. A maximum of 5 waypoints can be set.
Destination:
Indicates the destination location of the route guidance.
Upon reaching the destination, the address will be displayed on the map screen.
Suggested route:
Appears in bold yellow during route guidance.
Map Menu icon:
Touch the icon to display the Map
Menu screen.
“Map menu screen” (page 2-18)
/ Direction indicator:
Indicates the directional setting of the map. Touch the icon to change the setting.
: North always pointing up.
: Direction of the vehicle always pointing up.
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (33,1)
2. Getting started
“Setting map orientation”
(page 3-14)
Scale indicator:
Indicates the scale of the map.
Touch the icon to display the scale bar.
The map scale can be adjusted using the scale bar.
“Operating with touch panel operation” (page 3-5)
Street name:
Displays the name of the street that the vehicle is currently driving on.
IVR soft button (if so equipped):
Touch the icon to connect to the Infiniti
Connection TM Interactive Voice Menu.
“Connecting to Interactive Voice
Menu” (page 7-10)
SETTING VOICE GUIDANCE
TURNING VOICE GUIDANCE ON/OFF
Voice guidance can be activated or deactivated.
IGT0119
1. Push <ROUTE>.
2. Highlight [Guidance Settings] and push
<ENTER>.
INFO:
Infiniti Connection Interactive Voice Menu is a feature of Infiniti Connection. Use of this feature is dependent upon a valid subscription and the telematics device being in operative condition, as well as cellular connectivity, navigation map data and GPS satellite signal reception being available.
IGT0120
3. Highlight [Guidance Voice] and push
<ENTER>. The indicator illuminates if voice guidance is activated.
Other settings
Voice guidance can also be activated or deactivated by performing the following procedure.
IGT0121
1. Push <SETTING>.
2. Highlight [Volume & Beeps] and push
<ENTER>.
3. Highlight [Guidance Voice] and push
<ENTER>.
ADJUSTING VOICE GUIDANCE VO-
LUME
The volume of voice guidance can be adjusted.
2-25
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (34,1)
2. Getting started
IGT0119
1. Push <ROUTE>.
2. Highlight [Guidance Settings] and push
<ENTER>.
IGT0123
4. Adjust the volume of voice guidance by using the INFINITI controller.
Other settings
The volume of voice guidance can also be adjusted by performing the following procedure.
3. Highlight [Guidance Volume] and push
<ENTER>.
4. Adjust the volume of voice guidance by using the INFINITI controller.
INFO:
The guidance volume can also be adjusted by turning the audio system volume control knob or pushing <+>/<−> on the steering wheel while voice guidance is being announced.
“Steering wheel switches” (page 2-7)
IGT0122
3. Highlight [Guidance Volume] and push
<ENTER>.
IGT0124
1. Push <SETTING>.
2. Highlight [Volume & Beeps] and push
<ENTER>.
2-26
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (35,1)
2. Getting started
INFINITI VOICE RECOGNITION
INFINITI Voice Recognition allows handsfree operation of the navigation system and other systems equipped on this vehicle, such as the phone, vehicle information and audio.
INFINITI Voice Recognition can be used in one of two selectable modes, Standard
Mode or Alternate Command Mode.
In Standard Mode, the commands that are available are always shown on the display and announced by the system. To perform operations, simply follow the prompts given by the system.
For advanced operations, change to Alternate Command Mode. When this mode is active, an expanded list of commands can be spoken after pushing <TALK > on the steering wheel, and the voice command menu prompts are turned off. Note that in this mode the recognition success rate may decrease because there are more commands available and more ways of speaking each command. Otherwise, it is recommended that Alternate Command
Mode be turned off and Standard Mode be used for the best recognition performance.
INFO:
. For U.S. customers, Standard Mode is selected by default. For Canadian customers, Alternate Command Mode is the default mode.
. For voice recognition system operations related to the phone, audio or vehicle information systems, refer to the vehicle
Owner’s Manual.
. When the system language is set to
“Français” (French) or “Español” (Spanish), the available commands and functions may differ from those that are available when using the system in English.
USING VOICE RECOGNITION SYS-
TEM
Initialization
When the ignition switch is pushed to the
ON position, INFINITI Voice Recognition is initialized, which may take up to one minute. When completed, the system is ready to accept voice commands. If <TALK
> is pushed before the initialization completes, the display will show the message: “System not ready.”
BEFORE STARTING
To get the best recognition performance from INFINITI Voice Recognition, observe the following points.
. The interior of the vehicle should be as quiet as possible. Close the windows to eliminate the surrounding noises (traffic noise, vibration sounds, etc.), which may prevent the system from correctly recognizing the voice commands.
. The voice recognition system cannot be operated when the retractable hard top is not closed (for G37 Convertible only).
. Wait until the tone sounds before speaking a command.
. Speak in a natural conversational voice without pausing between words.
. If the air conditioner is set to “AUTO”, the fan speed is automatically lowered so that commands can be recognized more easily.
2-27
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (36,1)
2. Getting started
GIVING VOICE COMMANDS
The method of giving a voice command in
Standard Mode is described here.
Type A INI0267
Type B
2-28
Condition: Language=NAM_English/
INI0376
Type C IGT0208
1. Push <TALK wheel.
Type E JNB0288X
> located on the steering
Type D IGT0233
IGT0125
2. A list of commands appears on the screen, and the system provides the voice menu prompt, “Would you like to access Phone, Navigation, Information,
Audio or Help?”.
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (37,1)
2. Getting started
3. After the tone sounds and the icon on the screen changes from [ ] to [ ], speak a command.
4. Continue to follow the voice menu prompts and speak after the tone sounds until the operation is completed.
Operating tips
. Speak a command after the tone.
. Commands that are available are always shown on the display and spoken through voice menu prompts. Commands other than those that are displayed are not accepted. Please follow the prompts given by the system.
. If the command is not recognized, the system announces, “Please say again”.
Repeat the command in a clear voice.
. Push <BACK> once to return to the previous screen.
. Push and hold <TALK > to cancel the command. The message, “Voice recognition is canceled” will be announced.
. Push <TALK > to stop the voice prompt and give the command at once.
Remember to wait for the tone before speaking.
. To adjust the volume of the system feedback, push the volume control buttons <+> or <−> on the steering wheel or use the audio system volume control knob while the system is making an announcement.
VOICE COMMAND EXAMPLES
To use the voice recognition system, speaking one command is sometimes sufficient, but at other times it is necessary to speak two or more commands. As examples, some additional basic operations that can be performed by voice commands are described here.
Example 1: Placing call to phone number
800-662-6200
1. Push <TALK wheel.
> located on the steering
2. The system announces, “Would you like to access Phone, Navigation, Information, Audio or Help?”.
3. Speak “Phone”.
4. Speak “Dial Number”.
JVH0493X
IGT0135
5. Speak “800”.
IGT0137
2-29
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (38,1)
2. Getting started
IGT0138
6. The system announces, “Please say next three digits or dial, or say change number”. Speak “662”.
IGT0139
7. The system announces, “Please say last four digits or say change number”.
Speak “6200”.
IGT0140
8. The system announces, “Dial or Change
Number?”. Speak “Dial”.
IGT0141
9. The system makes a call to 800-662-
6200.
INFO:
. Speaking “800-662-6200” (10 continuous digits) or “662-6200” (7 continuous digits) is acceptable, if the area code is not necessary. However the 3-3-4 digit grouping is recommended for improved recognition.
“How to speak numbers” (page 9-14)
. The INFINITI voice recognition system is not limited to recognizing phone numbers of only 7 or 10 digits. To dial a number in a format other than the 3-3-4 digit grouping, use the “International Call” command.
. If “Change Number” is spoken during phone number entry, the system will automatically request that the number be repeated using the 3-3-4 format. In this case, speak the area code first and then follow the prompts.
. Do not add a “1” in front of the area code when speaking phone numbers.
. If the system does not recognize a spoken voice command, try repeating the command using a natural voice. Speaking too slowly or too loudly may further reduce recognition accuracy.
Example 2: Placing international call to phone number 011-81-111-222-333
1. Push <TALK wheel.
> located on the steering
2-30
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (39,1)
IGT0142
2. The system announces, “Would you like to access Phone, Navigation, Information, Audio or Help?”.
3. Speak “Phone”.
5. Speak “01181111222333”.
2. Getting started
IGT0144
7. The system makes a call to 011-81-
111-222-333.
INFO:
Any digit input format is available in the international number input process.
Example 3: Setting destination by street address
1. Push <TALK wheel.
> located on the steering
4. Speak “International Call”.
JVH0493X
6. Speak “Dial”.
Condition: Language=NAM_English/
IGT0145
IGT0126
2. The system announces, “Would you like to access Phone, Navigation, Information, Audio or Help?”.
3. Speak “Navigation”.
IGT0146
2-31
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (40,1)
2. Getting started
4. Speak “Address”.
JNB0276X
6. Speak the name of the city, “Gardena”.
INFO:
Only the official street names stored in the map database can be recognized by the system. To improve accuracy, speak the street name precisely and include boulevard, way, north, south, etc. If the full name is not known, speaking only part of the street name such as “Figueroa” is acceptable, but recognition accuracy may be reduced.
IGT0128
5. Speak the name of the state, “California”.
IGT0129
9. Speak the name of the street, “South
Figueroa Street”.
IGT0132
10. Voice feedback will be provided when the command is accepted, and the list of street names appears.
11. After the tone sounds and the icon on the screen changes again, speak
“One”.
IGT0130
IGT0131
7. Voice feedback will be provided when the command is accepted, and the list of city names is displayed.
8. After the tone sounds and the icon on the screen changes again, speak
“Four”.
2-32
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (41,1)
2. Getting started
IGT0133
12. Speak the house number.
“How to speak numbers”
(page 9-14)
INFO:
If the house number is not known, speak
“No house number”.
IGT0134
13. To confirm the destination location on the map, speak “Show Map”. To calculate a route, speak “Calculate
Route”.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
2-33
Black plate (42,1)
2. Getting started
COMMAND LISTS
Category Command
Phone
Navigation
Information
Audio
Help
Navigation
Phone
Command
Destination Home
Address
Places
Address Book
Previous Destinations
Command
Dial Number
Quick Dial
Phonebook
Call History Incoming Calls
Outgoing Calls
International Call
Missed Calls
2-34
Action
Operates the Phone function.
Operates the Navigation function.
Displays the Vehicle Information function.
Operates the Audio function.
Displays the User Guide.
Action
Sets a route to the home location that is stored in the Address book.
Searches for a location by the street address specified, and sets a route (for continental U.S.
and Canada only).
Sets a route to a facility near the current vehicle location.
Searches for information stored in the Address Book.
Sets a route to a previous destination.
Action
Makes a call to a spoken phone number up to 10 digits.
Makes a call to a contact that is stored in the Quick Dial.
Makes a call to a phone number stored in a mobile phone.
Makes a call to an incoming call number.
Makes a call to a dialed number.
Makes a call to a missed calls number.
Makes an international call by allowing more than 10 digits to be spoken.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (43,1)
2. Getting started
Information
Audio
Command
Fuel Economy
Trip Computer (if so equipped)
Maintenance
Where am I?
Traffic Information
Command
AM
FM
XM
CD
Action
Displays fuel economy information.
Displays trip information.
Displays maintenance information.
Displays GPS information.
Turns the traffic information system on and off.
Action
Turns to the AM band, selecting the station last played.
Turns to the FM band, selecting the station last played.
Turns to the SiriusXM Satellite Radio band, selecting the channel last played.
Starts to play a CD.
General Command
Go back
Exit
Action
Corrects the last recognition result to return to the previous screen.
Cancels Voice Recognition.
INFO:
Refer to the vehicle Owner’s Manual for the operations related to phone, information and audio.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
2-35
Black plate (44,1)
2. Getting started
MEMO
2-36
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
3 Map settings
Operating with ZOOM buttons (if
Black plate (45,1)
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
3. Map settings
MAP TYPES
Two types of map views are available: 2D map and Birdview TM (3D) map.
2D MAP
The 2D map displays the map in a 2dimensional environment similar to a road map.
Screen information
3-2
Condition: Language=NAM_English/
Black plate (46,1)
JNC0199X
Vehicle icon:
Indicates the current vehicle location and the direction of travel.
Guide point:
Indicates a guide point on the route.
Remaining time and distance to the destination:
Indicates the approximate remaining time and distance to the destination or waypoint. This indicator will appear when a destination or waypoint is set and route guidance is started.
When the vehicle is not driven on the suggested route, the screen displays the direction to the destination and the distance to the destination from the current vehicle position.
“Switching estimated arrival time display” (page 5-29)
Suggested route:
Appears in bold yellow during route guidance.
/ Direction indicator:
Indicates the directional setting of the map. Touch the icon to change the setting.
: North always pointing up.
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (47,1)
3. Map settings
: Direction of the vehicle always pointing up.
“Setting map orientation”
(page 3-14)
Scale indicator:
Indicates the scale of the map. Touch the icon to display the scale bar.
The map scale can be adjusted using the scale bar.
“Operating with touch panel operation” (page 3-10)
Arrow:
Indicates the distance to the next guide point and the turning direction at that guide point.
Stored location (orange):
Displays the locations that are stored in the Address Book. Icons can be changed according to personal preferences.
“Storing location” (page 6-2)
Avoid Area (green or blue):
Displays the areas to avoid that are stored in the Address Book with green or blue icons. During the route search, the route guidance is performed by searching for a route that avoids those areas.
“Storing avoid area” (page 6-7)
Street name:
Displays the name of the street the vehicle is currently driving on.
Traffic indicator:
Displays the reception condition of the traffic information transmitted from the provider.
Green: Reception condition is good.
Gray: Reception condition is not good.
No mark: Subscription to NavTraffic service is not detected.
Birdview
TM
(3D) MAP
Birdview TM displays the map from an elevated perspective. In Birdview TM , it is easy to recognize an image of the route because it provides a panoramic view over a long distance.
IMA0073
INFO:
Note the following items about the Birdview TM display.
. “Birdview TM ” is a registered trademark of
Clarion Co., Ltd.
. The map in Birdview TM always appears with the current forward direction facing up.
BUILDING GRAPHICS
In an area where the building graphics are stored in the map data, the building graphics are displayed when the map is zoomed in. On the 2D map display, these are called “Building footprint graphics”, and on the Birdview TM display, these are called “3D building graphics”.
The method to look at the map is the same for the 2D and Birdview TM maps.
3-3
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
3. Map settings
DISPLAYING CURRENT VEHICLE LOCA-
TION
OPERATING WITH CONTROL PANEL
Black plate (48,1)
3D building graphics (Birdview TM
INFO:
In an area where the building graphics are not stored in the map data, the normal map is displayed even when the map is zoomed in.
The basic map screen displays the current location (the position where the vehicle mark is located). Push <MAP> to display the current location on the map while on any screen.
3-4
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
IMA0076
Black plate (49,1)
3. Map settings
OPERATING WITH TOUCH PANEL
OPERATION
MOVING MAP
IMA0077
After moving the map, touch [BACK] on the map screen to display the current location map screen.
Condition: Language=NAM_English/
The operations for moving across the map are different between the 2D and Birdview TM maps.
2D MAP
Screen information:
Cross pointer
Distance from the current location to the cross pointer
IMA0171
Street name
Operating with INFINITI controller
Push one of the directional buttons or the slide switch. Press and hold a directional button or the slide switch to move continuously across the map in a direction.
While moving across the map, the cross pointer appears.
If the map scale is set to 1/8 mile (200 m) or less, the street indicated by the cross
3-5
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (50,1)
3. Map settings pointer will blink in pink and the street name will be displayed.
Operating with touch operation
IMA0079
1. Touch the screen.
The cross pointer is displayed, and the touched position is set as the center of the screen.
INFO:
While driving, one touch continuous scrolling is disabled. Touch the screen again to scroll further.
If the map screen is set to the building footprint graphics, the map cannot be scrolled while driving.
Fine-tuning the cursor position: IMA0082
2. Touch the 8-directional key to adjust the cross pointer position. Touch
[BACK] to complete the adjustment.
INFO:
Fine-tuning the cursor position is not possible while driving.
1. Touch [Slow].
The 8-directional key is displayed.
IMA0081
IMA0080
2. Touch the direction to move to. The map continues to scroll while the screen is touched.
3-6
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Birdview
TM
(3D) MAP
Black plate (51,1)
3. Map settings
Operating with touch panel
IMA0084
1. Touch the screen.
The cross pointer and 8-directional key are displayed.
Screen information:
Cross pointer
Street name
Distance from the vehicle position to the cross pointer
Rotates the map clockwise.
Rotates the map counterclockwise.
Moves the cross pointer in the direction of the arrow.
IMA0172
Operating with INFINITI controller
Push one of the directional buttons or the slide switch. Press and hold a directional button or the slide switch to move continuously across the map in a direction.
While moving on the map, the cross pointer appears.
IMA0084
2. Touch the direction to move to. The map continues to scroll while the screen is touched.
3-7
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (52,1)
3. Map settings
IMA0086
3. Touch [ ] or [ ] to change the direction of the map.
:
: Rotates the map clockwise.
Rotates the map counterclockwise.
INFO:
While driving, one touch continuous scrolling is disabled. Touch the screen again to scroll further.
CHANGING SCALE OF MAP
OPERATING WITH ZOOM BUTTONS (if so equipped)
3-8
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
IMA0087
Black plate (53,1)
3. Map settings
Push <ZOOM IN> or <ZOOM OUT>. A scale appears on the right side of the screen.
To view the map in detail, push <ZOOM IN>.
To view a wider area, push <ZOOM OUT>.
The scale will automatically disappear when neither <ZOOM IN> nor <ZOOM
OUT> has been pushed for several seconds.
If the scaling operation is not performed for a specified period of time, the scale display disappears.
INFO:
Free zoom:
The scale can be changed in smaller steps when
<ZOOM IN> or <ZOOM OUT> is pushed and held than when the button is pushed briefly. When the button is pushed briefly, the scale can be changed in large steps.
“Other navigation settings” (page 8-7)
OPERATING WITH CENTER DIAL
1. Turn the center dial when the map screen is displayed. The map scale is displayed at the right side of the screen.
2. Use the center dial to adjust the map scale.
Clockwise: Zoom in
Counterclockwise: Zoom out
IMA0173
INFO:
Free zoom:
Depending on the setting, using the center dial to change the map scale may adjust the scale normally, or it may engage the free zoom (finer scale adjustment in smaller steps).
“Other navigation settings” (page 8-7)
3-9
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (54,1)
3. Map settings
OPERATING WITH TOUCH PANEL
OPERATION
1. Touch [ ].
The scale is displayed.
IMA0089
IMA0090
2. Touch [ZOOM IN] or [ZOOM OUT] to change the scale.
INFO:
Free zoom:
Once the [Small Step Zoom by Dial] is set to ON in the setting screen, the scale can be changed in smaller steps when [ZOOM IN] or [ZOOM OUT] is pushed and held than when either button is briefly pushed. If briefly pushed, the operation returns to normal.
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
To change the map scale:
“Zoom In
<1 to 13>
mand Mode)
” (Alternate Com-
“Zoom Out mand Mode)
<1 to 13>
” (Alternate Com-
MAP SCALE
Any required map scale (map coverage) between 320 miles (640 km) and 1/64 of a mile (25 m) can be selected.
Scale level for 2D map and Birdview
TM
map (3D) display
Normal Map
Shows building footprint graphics
US Units
320 miles
80 miles
32 miles
8 miles
5 miles
2 miles
1 mile
1/2 mile
1/4 mile
1/8 mile
1/16 mile
1/32 mile
1/32 mile
1/64 mile
Metric Units
640 km
160 km
64 km
16 km
10 km
4 km
2 km
1 km
500 m
200 m
100 m
50 m
50 m
25 m
3-10
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Example: The most detailed level (Birdview TM map)
Condition: Language=NAM_English/
Black plate (55,1)
3. Map settings
CHANGING MAP VIEW
The map view can be changed between the
2D and Birdview TM maps. The map can also be displayed in the split screen mode.
Example: The widest level (Birdview map)
INFO:
The traffic information icons are not displayed on the map screen when the map scale is set to
32 miles (64 km) or higher.
“Traffic information display and scale levels” (page 7-19)
IMA0095
1. Push <ENTER> while the current location map screen is displayed.
IMA0097
2. Highlight [Map View] and push
<ENTER>.
3-11
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (56,1)
3. Map settings
IMA0097
3. Highlight [Change View] and push the right button of the directional buttons or push the slide switch to the right.
4. Highlight the preferred map view and push <ENTER>. The indicator of the selected map view illuminates.
5. The display automatically returns to the map screen.
Available views
. [2D Map]:
Switches to the 2D map.
. [Birdview (3D)]:
Switches to the Birdview TM map.
. [Split: 2D Map]:
Changes to the split screen mode and both halves display maps in 2D.
. [Split: Birdview Map]:
Changes to the split screen mode and
3-12 the left half displays the map in 2D and the right half displays the map in
Birdview TM .
INFO:
. When the split screen mode is selected, the map settings for the left screen can be changed independently.
“Setting left screen display”
(page 3-17)
. If the split screen mode is selected, the normal map scrolling and scale adjustment are set in the right screen.
. The map direction or scale for each screen can be adjusted independently by touching an icon on the map.
Split: Birdview TM Map IMA0099
OTHER SETTINGS
The map view can also be set by performing the following procedure.
Split: 2D Map IMA0098
IMA0100
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Map View] and push
<ENTER>.
4. Highlight [Change View] and push
<ENTER>.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (57,1)
3. Map settings
5. Highlight the preferred item and push
<ENTER>.
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
.
To display the 2D map:
“Plan View map” (Alternate Command Mode)
.
To display the Birdview TM map:
“Birdview map” (Alternate Command
Mode)
MAP VIEW SETTINGS
Other settings are also available for the map screen, such as changing the map direction, map color, Birdview TM angle, etc.
BASIC OPERATION
IMA0101
1. Push <ENTER> while the current location map screen is displayed.
IMA0103
3. Highlight [Map Settings] and push
<ENTER>.
IMA0102
2. Highlight [Map View] and push
<ENTER>.
IMA0104
4. Highlight the preferred item and push
<ENTER>.
Available setting items
. [Map Orientation]:
Sets the map direction to North Up or
Heading Up.
“Setting map orientation”
(page 3-14)
3-13
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (58,1)
3. Map settings
. [Long Range]:
Sets the long range map view display on/off.
“Settings long range map view”
(page 3-15)
. [Map Color]:
Changes the map color.
“Setting map color” (page 3-16)
. [Birdview Angle]:
Changes the Birdview TM
“Changing Birdview angle.
TM angle”
(page 3-16)
. [Left Split Map Settings]:
Sets the map settings for the left screen of the split map.
“Setting left screen display”
(page 3-17)
. [Show all Freeway Exits on Route]/
[Auto. Show Turn List on Freeway]:
Sets the display of the freeway exit information on/off.
“Show exit information on freeways” (page 5-11)
Other settings
The orientation of the map can also be set by performing the following procedure.
IMA0105
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Map View] and push
<ENTER>.
SETTING MAP ORIENTATION
The map direction (orientation) can also be changed in the 2D map. These settings are available only in the 2D map or 2D/2D split map.
IMA0106
1. Highlight [Map Orientation] and push
<ENTER>.
IMA0107
2. Highlight the preferred map orientation and push <ENTER>. The indicator of the selected map orientation illuminates.
3. Push <MAP> to return to the current location map screen.
Available map orientations
. [North Up]:
The top of the map remains oriented to the north, and the vehicle icon rotates
3-14
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (59,1)
3. Map settings on the map.
. [Heading Up]:
The vehicle icon always points up on the screen and the map rotates.
INFO:
If the map orientation is switched, the direction indicator icon displayed in the lower left corner is also switched.
: North Up
: Heading Up
North Up IMA0108
SETTINGS LONG RANGE MAP VIEW
The position of the vehicle icon can be changed to view a wider area in the traveling direction. If this function is activated, the vehicle icon is located slightly lower than the center of the screen.
Heading Up IMA0109
INFO:
The direction of the map can also be changed by touching the direction icon on the map screen.
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
To change the map direction:
“North Up” (Alternate Command Mode)
“Heading Up” (Alternate Command
Mode)
IMA0110
1. Highlight [Long Range] and push
<ENTER>. The indicator illuminates.
2. Push <MAP> to return to the current location map screen.
Condition: Language=NAM_English/
Long Range Map View IMA0111
3-15
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (60,1)
3. Map settings
INFO:
[Long Range] is displayed only when [Heading
Up] is selected.
SETTING MAP COLOR
The map color can be changed to a warm or cool color, or a light color, to emphasize the traffic information.
IMA0112
1. Highlight [Map Color] and push
<ENTER>.
2. Highlight the preferred map color and push <ENTER>. The indicator light of the selected color illuminates.
Available map colors
The following map colors are available.
. [Warm]:
Sets warm colors for the map coloring.
. [Cool]:
Sets cool colors for the map coloring.
. [Traffic Emphasis]:
Sets light colors for the map coloring to emphasize the traffic information.
INFO:
The effect of the setting changes can be confirmed on the preview displayed on the right side of the screen.
CHANGING Birdview
TM
ANGLE
The Birdview TM angle can be changed.
This setting is available only in the Birdview TM map or 2D/Birdview TM split map.
IMA0114
1. Highlight [Birdview Angle] and push
<ENTER>.
IMA0113
3-16
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (61,1)
3. Map settings
2. Adjust the Birdview TM
INFINITI controller.
IMA0115 angle using the
3. Push <MAP> to return to the current location map screen.
SETTING LEFT SCREEN DISPLAY
When the split screen is displayed, the map settings of the left screen can be changed.
IMA0116
1. Highlight [Left Split Map Settings] and push <ENTER>.
IMA0117
2. Highlight the preferred map setting and push <ENTER>.
3. Push <MAP> to return to the current location map screen.
Available setting items
. [Map Orientation]:
The map direction can be selected as follows.
— [North Up]:
The top of the map remains oriented to the north, and the vehicle icon rotates on the map.
— [Heading Up]:
The vehicle icon always points up on the screen and the map rotates.
. [Long Range]:
Positions the vehicle icon slightly lower than the center of the screen. This offers a wider view in the traveling direction.
. [Map Scale]:
Displays a scale on the left side of the screen. Use this to change the scale of a map.
INFO:
. The settings of the right screen are the same as the settings of the full screen map.
. The map settings can also be changed by touching the direction indicator or the scale
3-17
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (62,1)
3. Map settings indicator icon on the map.
3-18
Condition: Language=NAM_English/
LOOKING AT INFORMATION ON MAP
Icons can be displayed on the map, and information about destinations and landmarks can be displayed.
DISPLAYING MAP ICONS
The map icons can be displayed or hidden by type.
2. Highlight [Map Icons] and push
<ENTER>.
IMA0120
3. Highlight the preferred icon and push
<ENTER>. The icon display setting toggles between on and off each time
<ENTER> is pushed. The indicator of the selected icon illuminates.
IMA0118
1. Push <ENTER> while the current location map screen is displayed.
IMA0119
IMA0121
4. Push <MAP> to return to the current location map screen. The activated icons are displayed on the map.
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (63,1)
3. Map settings
INFO:
.
.
.
If they are registered in the map data, the brand icons will be displayed on the map instead of the general map icons listed below.
Map icons that can be displayed
The following map items can be displayed.
.
Restaurant
.
Gas Station
Hotel
ATM
Rest Area
Other settings
The map icons can also be set by performing the following procedure.
1. Push <SETTING>.
IMA0122
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Map Icons] and push
<ENTER>.
INFO:
. The map icons are not displayed on the map screen when the map scale is set to 1/4 mile (500 m) or higher in the 2D map, or to 1 mile (2 km) or higher in the Birdview TM map.
. When the [Small Step Zoom by Dial] is set to
ON; In 2D map, even when the map scale icon indicates 1/8 mile (200 m), the map icons are not displayed unless the map is set to the most zoomed in step within the scale level.
In Birdview TM map, even when the map scale icon indicates 1/2 mile (1 km), the map icons are not displayed unless the map is set to the most zoomed in step within the scale level.
MAP SCROLLING INFORMATION
Information about the location, on which the center of the cross pointer is placed by scrolling on the map, can be set to be displayed.
1. Push <SETTING>.
IMA0123
2. Highlight [Navigation] and push
<ENTER>.
IMA0124
3. Highlight [Others] and push <ENTER>.
3-19
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (64,1)
3. Map settings
.
[Latitude/Longitude Info]
IMA0125
4. Highlight [Map Scrolling Information] and push <ENTER>.
IMA0127
6. Push <MAP> to return to the current location map screen. Move the cross pointer to the set location to display the information.
IMA0126
5. Highlight the preferred information item and push <ENTER>. The indicator of the selected information item illuminates.
The following information items are available.
.
[Address Book Icons]
.
[Destination/Waypoint Icons]
3-20
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
MAP SYMBOLS
This navigation system uses symbols to display facilities.
Black plate (65,1)
3. Map settings
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
IMA0128
3-21
Black plate (66,1)
3. Map settings
ROAD COLOR
The road types are differentiated by colors.
Freeway:
(Red or light red (zoomed in))
Main road:
(Brown or dark yellow)
Narrow street:
(Gray)
Road with incomplete map data:
(Dark green)
TRAFFIC INFORMATION ON MAP
With a subscription to the NavTraffic service, traffic information is displayed.
“Viewing available traffic information”
(page 7-16)
Free Flow:
(Green)
Moderate traffic:
(Yellow)
Heavy traffic:
(Red)
Section affected by serious traffic event:
(Purple)
The following traffic information icons may
3-22 be displayed
: Accident
: Closed road
: Information
: Road work
: Slippery road
: Weather
: Incident
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (67,1)
4 Setting destination
Setting by Infiniti Connection TM (if
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (68,1)
4. Setting destination
DESTINATION SCREEN
There are several methods that can be used to set a destination. Understand the advantages of each method and select the best method for finding and setting a preferred destination.
JND0237X
BASIC OPERATION
1. Push <DEST>.
2. Highlight the preferred destination setting method and push <ENTER>.
Available setting items
. [Street Address] :
Searches for a destination by address.
. [Places] :
Searches for a destination from various categories of business or locations, or searches from the facilities in ZAGAT.
4-2
. [Home] :
Searches for a route from the current location to the previously stored home destination.
. [Address Book] :
Searches for a destination from the list of the stored locations.
. [Previous Destination] :
Searches for a destination from the previous destinations.
. [Connected Search] (if so equipped) :
Searches for a destination by connecting to the Infiniti Connection TM Data
Center.
Available setting items (next page screen)
. [Delete Destination] :
Deletes the currently set destination.
. [Previous Start Point] :
Sets the previous starting point as the destination.
. [Stored Routes] :
Selects a stored route.
. [Phone Number] :
Searches for a point of interest by a telephone number.
. [Freeway Entrance/Exit] :
Searches for a destination from a freeway entrance/exit.
. [Intersection] :
Searches for a destination from intersections.
. [City Center] :
Sets the center of a city as the destination.
INFO:
. [Connected Search] is a feature of Infiniti
Connection. Use of this feature is dependent upon a valid subscription and the telematics device being in operative condition, as well as cellular connectivity, navigation map data and GPS satellite signal reception being available.
.
[Phone Number] cannot be used to search for a location with a residential phone number.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (69,1)
4. Setting destination
CHANGING REGION
When setting a destination, the correct region must be selected.
To narrow down the location, the city can also be specified.
Specifying region
JND0238X
1. Push <DEST>.
2. Highlight [Change Region] and push
<ENTER>.
3. Highlight the preferred region and push
<ENTER>.
Available setting items
. US1: CA, NV
. US2: AZ, CO, ID, MT, NM, OR, UT, WA,
WY
. US3: IA, KS, MN, MO, ND, NE, SD
. US4: AR, LA, MS, OK, TX
. US5: IL, IN, MI, WI
. US6: DC, DE, KY, MD, OH, PA, VA, WV
. US7: CT, MA, ME, NH, NJ, NY, RI, VT
. US8: AL, FL, GA, NC, SC, TN
. US9: AK
. US10: HI
. Canada
. Puerto Rico
. Virgin Islands
INFO:
. It is also possible to select a region by touching the map on the right side of the screen.
. It is not possible to search for a route from the continental United States to Hawaii,
Puerto Rico and Virgin Islands.
Specifying city
When searching for a destination with
“Places”, “Freeway Entrance/Exit”, “Intersection” or “City Center”, the search can be narrowed down by specifying the city.
For “City Center”, you can only change the region.
As an example, the procedure for specifying the city from “Places” is described here.
IDE0103
1. Highlight [Select a City] and push
<ENTER>.
JNB0283X
4-3
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (70,1)
4. Setting destination
IDE0104
2. Enter the name of the city, highlight
[List] and push <ENTER>.
A list screen is displayed.
.
.
INFO:
The same screen will be displayed when a location is searched by “Street Address”, “Freeway Entrance/Exit” or “Intersection”, and when [City] is highlighted and <ENTER> is pushed.
“Finding address” (page 4-4)
Highlight [Last 5 Cities] and push
<ENTER> to display the last 5 cities recently set as destinations.
FINDING ADDRESS
When the address of the destination is known, use the following method to enter the address and then have the system calculate a route. A location near the preferred destination can also be searched by entering the house number if the map data contains the relevant data.
IDE0105
3. Highlight the city of the destination from the list and push <ENTER>.
INFO:
There are instances when the destination list screen number will be less than what was shown in the matches screen, but this is due to the system automatically determining that some destinations are duplicates. The “Matches” destinations includes duplicates. When the [LIST] is highlighted and <ENTER> is pushed, the system does a further analysis to remove the duplicates, so the number is sometimes less.
JND0239X
1. Push <DEST>, highlight [Street Address] and push <ENTER>. A character input screen is displayed.
IDE0107
4-4
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (71,1)
4. Setting destination
2. Enter the house number, highlight [OK] and push <ENTER>. If the house number is not available, highlight [No House #] and push <ENTER>. A street name input screen is displayed.
IDE0108
3. Enter the name of the street. After finishing the entry, highlight [List] and push <ENTER>. A list of streets is displayed.
INFO:
When [City] is highlighted and <ENTER> is pushed, a city can be specified by typing the city name.
“Specifying city” (page 4-3)
IDE0109
4. Highlight the correct street of the destination from the list and push
<ENTER>.
INFO:
In some cases, when a street name has been entered, the number of matching destinations in the “Matches” column may be different from the number displayed on the list screen. If this occurs, enter more characters to further reduce the number of matches.
5. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination, and push <ENTER>. The system sets the destination to the selected location and starts calculating a route.
INFO:
Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc.
“Procedures after setting destination”
(page 5-2)
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
To set the destination from a street address:
“Navigation” “Address” (Standard
Mode)
“Address” (Alternate Command Mode)
IDE0110
4-5
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (72,1)
4. Setting destination
INFO:
When using a voice command to set a street name, it is recommended that the complete street name is stated.
Examples:
Correct input – North Elm Street
East Jefferson Boulevard
Incorrect input – Elm Street
East Jefferson
FINDING PLACE
There are 3 methods that can be used to set the destination to places of interest: typing the name, choosing a category or selecting a ZAGAT reviewed location. To help improve searching, different start points can be chosen to search from such as near current location, near the destination or city center.
Finding nearby place
the categories that you frequently use.
JND0241X
1. Push <DEST>.
2. Highlight [Places] and push <ENTER>.
IDE0112
3. Highlight the preferred nearby category from the list and push <ENTER>.
A list screen is displayed.
INFO:
Highlight [Customize Nearby Places] to customize the 5 nearby categories to show
IDE0113
4. Highlight the preferred destination from the list, and push <ENTER>. The position of the selected location is displayed in the preview on the right side of the screen.
.
.
INFO:
A maximum of 100 facilities can be displayed on the list screen.
To search for facilities along your route, select [Show Along Route].
4-6
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Other settings:
Black plate (73,1)
4. Setting destination
Searching by other methods
IDE0114
5. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination, and push <ENTER>. The system sets the destination to the selected location and starts calculating a route.
INFO:
. If there is a route already set, the newly selected location can substitute a previously set destination or can be added to a route already set.
. To review the destination location again, highlight [Move Location] and push
<ENTER>.
IDE0115
The destination can also be set by pushing
<ENTER> in the current or scrolled location map screen and selecting [Nearby Places].
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
To display the nearby category list and select the destination from it:
“Navigation” “Places” (Standard Mode)
“Places” (Alternate Command Mode)
JND0241X
1. Push <DEST>.
2. Highlight [Places] and push <ENTER>.
IDE0117
3. Highlight [All Categories or Name] and push <ENTER>.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
4-7
Black plate (74,1)
4. Setting destination
INFO:
If [Select a City] is highlighted and <ENTER> is pushed, a city name input screen is displayed. Specify the city to be searched before narrowing down the categories.
“Specifying city” (page 4-3)
INFO:
To select a category by directly inputting the category name, highlight [Category Search] and push <ENTER>. The category name input screen is displayed.
IDE0118
4. Set the narrowing down conditions for the landmarks and push <ENTER>.
INFO:
Highlight [Change Region] and push
<ENTER> to change the region. A screen for selecting a region is displayed.
“Changing region” (page 4-3)
IDE0120
5. Highlight the main category from the list and push <ENTER>.
IDE0122
6. Highlight the subcategory and push
<ENTER>.
INFO:
Subcategories may not exist depending on the category that is selected.
IDE0119
IDE0121
IDE0123
4-8
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (75,1)
4. Setting destination
7. Enter the name of the destination facility and highlight [List], and then push <ENTER>.
The facility list is displayed.
.
.
.
INFO:
It is not necessary to enter the facility name completely. It is also possible to display the list screen only by highlighting [List] without entering the facility name and pushing <ENTER>.
The number of narrowed down points are displayed in the “Matches” column.
Up to two keywords (part of the facility name) can be entered by highlighting
[AND Search] and pushing <ENTER> after entering the first facility name.
IDE0124
INFO:
The facility name can also be entered directly by highlighting [Choose Name] on the main category list screen and pushing
<ENTER>
IDE0125
8. Highlight the preferred destination from the list, and push <ENTER>.
.
.
INFO:
By highlighting [Sort] and pushing
<ENTER>, options can be sorted from
[By Name] or [By Dist.]. When selecting
[By Dist.], the position of the selected location is displayed in the preview on the right side of the screen.
In some cases, when a facility name has been entered, the number of matching destinations in the “Matches” column may be different from the number
.
displayed on the list screen. If this occurs, enter more characters to further reduce the number of matches.
The search conditions can be changed by highlighting [Refine] and pushing
<ENTER>.
IDE0126
9. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination and push <ENTER>. The system sets the destination to the selected location and starts calculating a route.
INFO:
Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc.
“Procedures after setting destination”
(page 5-2)
4-9
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (76,1)
4. Setting destination
Searching for restaurant using ZA-
GAT
6. Highlight [RESTAURANT] and push
<ENTER>. A list screen is displayed.
JND0242X
1. Push <DEST>.
2. Highlight [Places] and push <ENTER>.
IDE0129
4. Highlight the preferred state and push
<ENTER>. A list screen is displayed.
IDE0133
7. Highlight the preferred category and push <ENTER>. A list screen is displayed.
IDE0128
3. Highlight [ZAGAT] and push <ENTER>.
IDE0130
5. Highlight the preferred city and push
<ENTER>. A list screen is displayed.
IDE0132
8. Highlight the preferred sorting order and push <ENTER>. A list screen is displayed.
IDE0131
4-10
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (77,1)
4. Setting destination
SETTING HOME AS DESTINATION
The home location can be set as the destination to which the system calculates a route. This function is especially useful when searching for a route to return to the home location.
IDE0134
9. Highlight the preferred destination facility from the list, and then push
<ENTER>.
.
.
.
INFO:
By highlighting [Sort] and pushing
<ENTER>, sorting options can be selected to re-sort the list.
The search conditions can be changed by highlighting [Refine].
By highlighting [Ratings] and pushing
<ENTER>, an explanation of the ZAGAT ratings can be displayed.
IDE0135
10. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination and pushing <ENTER>. The system sets the destination to the selected location and starts calculating a route.
INFO:
Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc.
“Procedures after setting destination”
(page 5-2)
* 2009 Zagat Survey, LLC. Zagat Survey is a registered trademark of Zagat Survey,
LLC.
JND0243X
1. Push <DEST>.
2. Highlight [Home] and push <ENTER>.
IDE0137
3. The home location is displayed, and the system sets the home location as the destination.
4-11
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (78,1)
4. Setting destination
INFO:
If the home location is not stored yet, the system will automatically display a screen for storing it.
“Storing location” (page 6-2) destination:
“Navigation” “Destination Home”
(Standard Mode)
“Destination Home” (Alternate Command Mode)
SEARCHING FROM ADDRESS BOOK
Storing frequently used destinations in the
Address Book makes it easy for the system to set and calculate a route. To utilize this function more effectively, destinations that are often traveled to should be stored in advance.
IDE0140
3. Highlight the preferred location from the list and push <ENTER>.
INFO:
Selecting [Sort] displays a list of various sort functions. To use the sort functions, stored locations must be set in advance.
“Storing location” (page 6-2)
IDE0138
4. The entire route to the home location is shown on the map. Highlight [Start] after confirming the location of the displayed destination, and push
<ENTER>. The system sets the destination to the selected location and starts calculating a route.
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
To set the home location as the
4-12
JND0244X
1. Push <DEST>.
2. Highlight [Address Book] and push
<ENTER>. A list screen is displayed.
IDE0141
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (79,1)
4. Setting destination
.
INFO:
Sorted By Number:
The Address Book entries are displayed in ascending numerical order.
.
.
.
Sorted By Name:
The Address Book entries are displayed in alphabetic order.
Sorted By Icon:
By selecting a particular icon, a list that contains only the Address Book entries associated with that icon is displayed.
Sorted By Group:
By selecting a particular group (family, friends, leisure, etc.), the selected group is displayed at the top of the list.
destination to the selected location and starts calculating a route.
INFO:
Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc.
“Procedures after setting destination”
(page 5-2)
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
To set the destination from the Address
Book:
“Navigation” “Address Book” (Standard Mode)
“Address book” (Alternate Command
Mode)
SETTING PREVIOUS DESTINATION
It is possible to set the destination to a location that has been previously set as a destination and have the system calculate a route. Up to 300 previous destinations will be automatically stored.
If the number of previous destinations exceeds 300, the oldest one will be replaced by the newest one.
JND0245X
1. Push <DEST>.
2. Highlight [Previous Destinations] and push <ENTER>. A list screen is displayed.
IDE0142
4. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination, and push <ENTER>. The system sets the
4-13
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (80,1)
4. Setting destination
IDE0144
3. Highlight the preferred destination from the list and push <ENTER>.
INFO:
The list can be sorted by selecting [By Date] or [By Name]. Highlight [By Date] to sort the list in chronological order. Highlight [By
Name] to sort the list in alphabetical order.
destination to the selected location and starts calculating a route.
INFO:
Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc.
“Procedures after setting destination”
(page 5-2)
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
To display the previous destinations list:
“Navigation” “Previous Destinations”
(Standard Mode)
“Previous Destinations” (Alternate
Command Mode)
SETTING BY INFINITI CONNECTION
TM
(if so equipped)
It is possible to set the destination using the Infiniti Connection features.
“Infiniti Connection TM ” (page 7-3)
INFO:
Use of Infiniti Connection features is dependent upon a valid subscription and the telematics device being in operative condition, as well as cellular connectivity, navigation map data and
GPS satellite signal reception being available.
Searching by connecting Data Center
You can find your point of interest by inputting a keyword and connecting to the
Infiniti Connection Data Center. The searched location can be set as a destination.
1. Push <DEST>.
IDE0145
4. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination, and push <ENTER>. The system sets the
4-14
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (81,1)
4. Setting destination
JND0231M
2. Highlight [Connected Search] and push
<ENTER>.
JND0234M
4. Highlight the preferred destination from the list and push <ENTER>.
Setting from information feeds
If the downloaded Infiniti Connection information feed has location data, you can set it as a destination. It is also possible to use various Infiniti Connection services set using the Infiniti Connection website such as “Destination Send-to-
Vehicle”, “My Schedule” or “Journey Planner features”, etc. to set a destination.
For details of the services and settings, refer to the Infiniti Connection website: www.infiniticonnection.com (for U.S.)/ https://canada.infiniticonnection.com (for
Canada), or contact the Infiniti Connection support line at 1-800-334-7858 (for U.S.)
/1-855-892-7418 (for Canada).
JND0233M
3. Enter the keyword, highlight [Search] and push <ENTER>. The system will connect to the Infiniti Connection Data
Center and the search results will be displayed.
INFO:
The search history can also be reused by highlighting [History] and pushing <ENTER>.
JND0232M
5. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination, and push <ENTER>. The system sets the destination to the selected location and starts calculating a route.
JNG0147M
1. Push <INFO>.
2. Highlight [Infiniti Connection] and push
<ENTER>.
4-15
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (82,1)
4. Setting destination
Searching by using IVR soft button on map
SETTING PREVIOUS START POINT
It is possible to set the destination to the start point of a previous route guidance and have the system calculate a route.
JNG0161M
3. Highlight [Sync All Information Feeds] and push <ENTER>. A list screen is displayed. Highlight the preferred information feeds and push <ENTER>.
INFO:
The methods for setting a destination differ depending on the specific service (Destination
Assistance, Destination Send-to-Vehicle and
Connected Search, etc.) and Infiniti Connection services may be updated during ownership.
Please see www.infiniticonnection.com (for
U.S.)/https://canada.infiniticonnection.com (for
Canada) for the latest features and services, as well as the most up-to-date user guide.
JNG0187X
It is possible to set a destination by touching the IVR (Interactive Voice Response) soft button * on the map. You can choose from the options provided by the voice guidance and speak your choice, or ask the Infiniti Connection Response
Specialists directly to search for your destination.
“Connecting to Interactive Voice
Menu” (page 7-10)
JND0246X
1. Push <DEST>.
2. Highlight [Next Page] and push
<ENTER>.
IDE0147
3. Highlight [Previous Start Point] and push <ENTER>.
4-16
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (83,1)
4. Setting destination
2. After the tone sounds, speak a command.
To set a previous start point as the destination:
“Previous Start Point” (Alternate Command Mode)
SETTING FROM STORED ROUTES
It is possible to select a preferred route from the stored routes.
IDE0150
3. Highlight [Stored Routes] and push
<ENTER>. A list screen is displayed.
IDE0148
4. The previous start point is set as a destination, and the entire route is shown on the map. Highlight [Start] after confirming the location of the displayed destination, and push
<ENTER>. The system sets the destination to the selected location and starts calculating a route.
INFO:
Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc.
“Procedures after setting destination”
(page 5-2)
Voice command
1. Push <TALK wheel.
> located on the steering
JND0247X
1. Push <DEST>.
2. Highlight [Next Page] and push
<ENTER>.
IDE0151
4. Highlight the preferred route from the list and push <ENTER>. The route to the destination is set.
4-17
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (84,1)
4. Setting destination
IDE0152
5. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination, and push <ENTER>. The system sets the destination to the selected location and starts calculating a route.
INFO:
. Even after setting a destination, the location of the destination can be adjusted, the location can be stored, etc.
“Procedures after setting destination”
(page 5-2)
. The stored route includes only locations
(destination and waypoints) and route calculation conditions, not the route itself.
Therefore, when the destination is set using a stored route, a different route may be suggested if the current vehicle location is different from the one when the route was
4-18 stored.
SETTING BY PHONE NUMBER
If the phone number of a facility is known, it is possible to search for a facility by entering the phone number, and have the system calculate a route.
INFO:
. Telephone numbers that were stored for stored destinations can also be used.
. If the area code of the specified telephone number does not exist in the map data, the system cannot search for the location.
. Only the locations included in the database in the map data can be searched by the phone number. Residential phone numbers cannot be used to search for a location.
JND0248X
1. Push <DEST>.
2. Highlight [Next Page] and push
<ENTER>.
IDE0154
3. Highlight [Phone Number] and push
<ENTER>. The telephone number input screen is displayed.
IDE0155
4. Enter the telephone number including the area code.
5. After finishing the entry, highlight [List] and push <ENTER>.
“Number input screen”
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (85,1)
4. Setting destination
(page 2-17)
IDE0156
6. A list screen is displayed if there are two or more search results. Highlight the preferred destination from the list and push <ENTER>.
A confirmation screen for the place name and the location is displayed, and the system starts calculating.
destination to the selected location and starts calculating a route.
INFO:
Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc.
“Procedures after setting destination”
(page 5-2)
SETTING FREEWAY ENTRANCE/EXIT
It is possible to set the destination to an entrance or exit of a freeway and have the system calculate a route.
IDE0159
3. Highlight [Freeway Entrance/Exit] and push <ENTER>. A character input screen is displayed.
IDE0157
7. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination, and push <ENTER>. The system sets the
JND0249X
1. Push <DEST>.
2. Highlight [Next Page] and push
<ENTER>.
IDE0160
4. Enter the name of the freeway.
5. After finishing the entry, highlight [List] and push <ENTER>.
4-19
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (86,1)
4. Setting destination
IDE0161
6. Highlight the freeway of the destination from the list, and push <ENTER>.
8. Select the preferred destination from the list. The position of the selected location is displayed in the preview on the right side of the screen. Then, push
<ENTER>.
IDE0164
INFO:
Select [By Distance] to sort the list by the nearest distance.
and push <ENTER>. The system sets the destination to the selected location and starts calculating a route.
INFO:
Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc.
“Procedures after setting destination”
(page 5-2)
SETTING INTERSECTION
It is possible to set an intersection of any two streets as the destination and have the system calculate a route.
IDE0162
7. Highlight [Entrance] or [Exit] and push
<ENTER>. A list screen is displayed.
IDE0163
IDE0165
9. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination,
JND0250X
1. Push <DEST>.
2. Highlight [Next Page] and push
<ENTER>.
4-20
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (87,1)
4. Setting destination
IDE0166
3. Highlight [Intersection] and push
<ENTER>. A character input screen is displayed.
IDE0168
5. Highlight a street as the 1st street from the list and push <ENTER>. A character input screen is displayed.
IDE0170
7. Highlight a street as the 2nd street from the list and push <ENTER>.
4. Enter the name of the 1st street.
IDE0167
After finishing the entry, highlight [List] and push <ENTER>. A list screen is displayed.
6. Enter the name of the 2nd street.
IDE0169
After finishing the entry, highlight [List] and push <ENTER>. A list screen is displayed.
IDE0171
8. The entire route is shown on the map.
Highlight [Start] after confirming the location of the displayed destination, and push <ENTER>. The system sets the destination to the selected location and starts calculating a route.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
4-21
Black plate (88,1)
4. Setting destination
INFO:
Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc.
“Procedures after setting destination”
(page 5-2)
SETTING CITY CENTER
It is possible to set the center of a city as a destination and have the system calculate a route.
IDE0172
3. Highlight [City Center] and push
<ENTER>. A character input screen is displayed.
IDE0174
5. Highlight the preferred destination from the list and push <ENTER>. The position of the selected location is displayed in the preview on the right side of the screen.
JND0251X
1. Push <DEST>.
2. Highlight [Next Page] and push
<ENTER>.
IDE0173
4. Enter the name of the city, highlight
[List] and push <ENTER>. A list screen is displayed.
INFO:
Highlight [Last 5 Cities] and push <ENTER> to display the last 5 cities recently set as destinations.
4-22
Condition: Language=NAM_English/
IDE0175
INFO:
Select [By Distance] to sort the list by the nearest distance.
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (89,1)
4. Setting destination
SETTING POINT ON MAP
It is possible to set a location scrolled to on the map as the destination and have the system calculate a route.
IDE0176
6. The selected destination is displayed at the center of the map. Highlight [Start] after confirming the location of the displayed destination, and push
<ENTER>.
The system sets the destination to the selected location and starts calculating a route.
INFO:
Even after setting a destination, the location of the destination can be adjusted, the route can be stored, etc.
“Procedures after setting destination”
(page 5-2)
IDE0177
1. Scroll the map, place the cross pointer over the preferred location, and push
<ENTER>.
.
.
INFO:
The map scale should be adjusted to search for a location more effectively.
The point on the blinking road where the center of the cross pointer is located can be set as a destination.
IDE0178
2. Highlight [New Dest.] and push
<ENTER>.
INFO:
For the items other than [New Dest.], refer to
“Map menu screen”.
“Scrolled location map screen”
(page 2-19)
IDE0179
3. The system sets the destination to the selected location and starts calculating a route.
4-23
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (90,1)
4. Setting destination
IDE0180
INFO:
If a point on a freeway is set as the destination, a confirmation message is displayed.
DELETE DESTINATION
It is possible to delete a destination and all waypoints that have already been set.
JND0252X
1. Push <DEST>.
2. Highlight [Next Page] and push
<ENTER>. Select [Delete Destination] and push <ENTER>.
deleted.
INFO:
The deleted destination and waypoints are not able to be reactivated.
Voice command
1. Push <TALK > on the steering wheel.
2. After the tone sounds, speak a command.
To delete a destination and all waypoints:
“Delete Destination” (Alternate Command Mode)
4-24
Condition: Language=NAM_English/
IDE0182
3. A confirmation message is displayed.
Select [Yes] and push <ENTER>.
The destination and the waypoints are
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
5 Route guidance
Black plate (91,1)
Searching for detour route taking traffic
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (92,1)
5. Route guidance
PROCEDURES AFTER SETTING DESTINA-
TION
After performing a route search, the route guidance can be immediately started. Also, it is possible to confirm or change a route.
IRG0085
Available items after setting destination
. [Start]:
Starts route guidance to the selected destination.
“Starting route guidance”
(page 5-2)
. [More Routes]:
Displays 3 alternative routes.
“Selecting route” (page 5-3)
. [Add/Route Info]:
Displays the route information. A destination or a waypoint can also be added.
5-2
“Confirming route” (page 5-3)
. [Move Location]:
Displays a map screen. The location of the destination can be adjusted.
“Moving location of destination”
(page 5-5)
. [Store Location]:
Stores the location in the Address
Book.
“Storing location” (page 5-5)
. [Place Info]:
Displays information about the facility that has been set as the destination, if it is included in the map data.
“Viewing information about searched location” (page 5-6)
INFO:
. If no operations have been performed on the system for several seconds, [Start] is automatically selected, and the system starts route guidance.
. When using waypoints, [More Routes] is disabled. After the route is started, push
<ROUTE> then select [Edit/Add to Route] to change the route between each waypoint.
. The same screen as when [Move Location] is selected can be displayed with the following operations:
— Touching the map screen
— Pushing the directional buttons except for the up/down button (INFINITI controller with directional buttons)
— Pushing the slide switch except in the upward/downward direction (INFINITI controller without directional buttons)
STARTING ROUTE GUIDANCE
IRG0085
1. Highlight [Start] and push <ENTER>.
Route guidance starts.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (93,1)
5. Route guidance
SELECTING ROUTE
IRG0086
1. Highlight [More Routes] and push
<ENTER>.
IRG0087
2. Highlight the preferred route condition and push <ENTER>.
3. The display automatically returns to the map screen.
Available route conditions
. [Short. Time] (purple):
Prioritizes by the shortest time.
. [Min. Freeway] (orange):
Minimizes the use of freeways.
. [Short. Dist.] (green):
Prioritizes by the shortest distance.
INFO:
. When the route is selected, a preview is displayed on the right side of the screen.
. The 3 routes may not always be different.
CONFIRMING ROUTE
IRG0088
1. Highlight [Add/Route Info] and push
<ENTER>.
2. Highlight the preferred information item and push <ENTER>.
3. Push <BACK> to return to the previous screen.
IRG0089
Available information
. [Turn List]:
Displays the details of the suggested route.
“Using turn list” (page 5-20)
. [Preview]:
The system will trace the planned route going forward or in reverse.
“Using route preview” (page 5-21)
. [Add Way Pt.]:
Edits the route by adding a waypoint or a destination.
“Adding destination or waypoint”
(page 5-4)
. [Store Route]:
Stores a calculated route. A maximum of 5 routes can be stored. Stored routes can be easily retrieved and set as the suggested route.
5-3
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (94,1)
5. Route guidance
“Storing route” (page 6-5)
. [Map Scroll]:
Displays a map screen where the location of the destination can be confirmed.
The same screen as when [Map Scroll] is touched can be displayed with the following operations:
— Touching the map screen.
— Pushing the directional buttons except for the up/down button (INFINITI controller with directional buttons).
— Pushing the slide switch except in the upward/downward direction (INFINITI controller without directional buttons).
Adding destination or waypoint
Before starting route guidance, destinations and/or waypoints can be added. A total of 6 destinations or waypoints can be set.
IRG0090
1. Highlight [Add Way Pt.] and push
<ENTER>.
IRG0092
3. Highlight [Add Destination] or [Add
Waypoint] and push <ENTER>.
IRG0091
2. Set additional destinations or waypoints and push <ENTER>.
The method of searching for a location is the same as the one for a destination.
“4. Setting destination”
IRG0093
4. The system starts calculating a route that includes the added destination or waypoint. When the calculation is finished, the route is displayed.
INFO:
. If a waypoint was added, [More Routes] cannot be selected.
5-4
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (95,1)
5. Route guidance
. If a destination was added, the prior destination becomes a waypoint.
MOVING LOCATION OF DESTINATION
The location of the destination can be adjusted by moving the cross pointer across the map.
IRG0094
1. Highlight [Move Location] and push
<ENTER>.
INFO:
The screen for adjusting the location also changes by touching the map screen displayed on the right side of the screen.
— Pushing the slide switch except upward/ downward (INFINITI controller without directional buttons).
STORING LOCATION
A searched location can be stored in the
Address Book. Then it can be easily retrieved and set as a destination (or waypoint).
IRG0095
2. Adjust the location by moving the cross pointer across the map and push
<ENTER>. The location of the destination is modified.
INFO:
. The map scale can be changed by turning the center dial or touching the scale icon.
The map scale can also be changed by pressing <ZOOM IN>/<ZOOM OUT> (if so equipped).
. The same screen as when [Move Location] is touched can be displayed with the following operations:
— Touching the map screen.
— Pushing the directional buttons except up/down buttons (INFINITI controller with directional buttons).
IRG0096
1. Highlight [Store Location] and push
<ENTER>.
IRG0097
5-5
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (96,1)
5. Route guidance
2. The location is stored in the Address
Book. The corresponding icon is displayed at the set location on the map.
VIEWING INFORMATION ABOUT
SEARCHED LOCATION
Information (street address and phone number) about places stored in the map data can be displayed.
2. Information about the location is displayed.
3. Push <BACK> to return to the previous screen.
INFO:
. If [Call] is displayed on the right side of the screen, it is possible to call the location indicated.
. The Bluetooth
®
Hands-Free Phone system is required to be active and the cellular phone connected to call the location indicated.
. Information about locations is not displayed while driving.
IRG0098
1. Select [Place Info] and push <ENTER>.
5-6
Condition: Language=NAM_English/
JNE0144M
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
ABOUT ROUTE GUIDANCE
After setting the route, select [Start] to begin route guidance.
Throughout route guidance, the system navigates you through the guide points using visual and voice guidance.
CAUTION!
GUID-37A33049-40E4-4C0E-9613-022BD3C96297
.
The navigation system’s visual and voice guidance is for reference purposes only.
The contents of the guidance may be inappropriate depending on the situation.
.
Follow all traffic regulations when driving along the suggested route (e.g., one-way traffic).
“Route guidance” (page 10-10)
VOICE GUIDANCE DURING ROUTE
GUIDANCE
When approaching a guide point (intersection or corner), destination, etc. during route guidance, voice guidance announces the remaining distance and/or turning direction. Push <VOICE> to repeat voice guidance.
Black plate (97,1)
5. Route guidance
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
5-7
Black plate (98,1)
5. Route guidance
Example of voice guidance
5-8
“In about one quarter mile (400 meters), right (left) turn.”
“Right (left) turn ahead.”
“In about one quarter mile (400 meters) freeway entrance on your right onto (road number and direction).”
“Freeway entrance on your right onto
(road number and direction).”
“In about one mile (1.6 kilometers), exit on your right.”
INI0119
“Exit on your right.”
“You have arrived at your destination.
Ending route guidance.”
GUIDANCE SCREENS AND PREVIEW
MODE
Route guidance displays map screens and various information according to the situation.
IRG0100
When route guidance starts, the Small Turn
Arrow on Map is displayed in the upper left corner of the map screen. This arrow indicates the turning direction at the next guide point (corner or intersection). The distance is also displayed. At the top of the screen, the distance to the next guide point and the name of the next street to turn on to are displayed. Also, there may be cases that next street names are announced. The
Small Turn Arrow on Map can be enabled or disabled by the user.
“Displaying small turn arrow on map”
(page 5-29)
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Turn list
Black plate (99,1)
5. Route guidance
Enlarged intersection view Junction guidance
IRG0101
When approaching a guide point, the system automatically changes to the split screen and shows an enlarged view of the intersection on the left screen. After passing through the intersection, the system automatically returns to the full screen mode. To switch to the full screen mode while the enlarged intersection view is displayed, push <MAP>. Pushing <MAP> again displays the enlarged intersection view.
IRG0102
While driving on a freeway, when the vehicle is approximately 1 mile (approximately 2 km) from a junction, the system automatically switches to the split screen and displays an enlarged view of the junction (3D) on the left screen. After passing the junction, the system automatically returns to the full screen mode. To switch to the full screen mode while the enlarged junction view is displayed, push
<MAP>.
IRG0103
Depending on the setting, the system can constantly display the split screen and show the turn list on the left screen. When approaching a guide point, the left screen automatically switches to an enlarged view of the intersection. To switch to the full screen mode, push <MAP>. Pushing <MAP> again displays the turn list.
“Guidance screen settings” (page 5-9)
GUIDANCE SCREEN SETTINGS
The guidance screen can be displayed at all times even when the vehicle is located away from the guide point. Various types of screens can be set.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
5-9
Black plate (100,1)
5. Route guidance
Split screen settings
The display setting on the left-hand side screen shown during route guidance can be changed.
IRG0104
1. Push <ENTER> while the current location map screen is displayed.
2. Highlight [Map View] and push
<ENTER>.
IRG0105
3. Highlight [View Settings] and push
<ENTER>.
4. Highlight the preferred screen and push <ENTER>. The indicator of the selected screen illuminates.
Intersection:
IRG0101
The map screen and the enlarged intersection view can be displayed at the same time.
Push <MAP> to switch to the full map screen.
Turn list:
The list screen for showing the guide points to the destination and the map screen can be displayed at the same time.
An enlarged intersection view is automatically displayed when the vehicle approaches the guide point.
The turn list can be scrolled using the center dial, the main directional buttons, the slide switch or by touching the up/ down button on the screen.
Push <MAP> to switch to the full map screen. Push <MAP> again to display the turn list.
Fuel Economy:
The current fuel consumption rate, average fuel consumption rate, instantaneous consumption rate and distance to empty can be displayed on the map screen. An enlarged intersection view is automatically displayed when the vehicle approaches the guide point.
Push <MAP> to switch to the full map screen.
Push <MAP> again to display the fuel economy screen. When approaching a guide point, the enlarged view of the intersection is automatically displayed. To
IRG0106
5-10
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (101,1)
5. Route guidance display the fuel economy information, push <MAP>.
To display the map screen, push <MAP> again.
NOTE:
Use the values displayed on the fuel economy screen as a guide. When the fuel gauge indicates empty or the low fuel warning light illuminates even if the distance to empty reading indicates a sufficient amount of fuel remains, refuel the vehicle as soon as possible.
Full map: map screen.
Show exit information on freeways
When the vehicle travels on a highway or a toll road, the display automatically provides exit information in the turn list.
3. Highlight [Map Settings] and push
<ENTER>.
IRG0109
1. Push <ENTER> while the current location map screen is displayed.
2. Highlight [Map View] and push
<ENTER>.
IRG0111
4. Highlight [Show all Freeway Exits on
Route] or [Auto. Show Turn List on
Freeway] and push <ENTER>. The indicator illuminates when the item is set.
5. Push <MAP> to return to the current location map screen.
Showing freeway exit information:
IRG0108
The current location map is displayed. An enlarged intersection view is automatically displayed when the vehicle approaches the guide point.
When an enlarged intersection view is displayed, pushing <MAP> returns to the
Condition: Language=NAM_English/
IRG0110
IRG0113
When [Show all Freeway Exits on Route] is set to ON and the route includes the
5-11
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (102,1)
5. Route guidance freeway or toll road, all exits along the route which have exit information will be shown in the turn list. The exit information is shown as icons.
Displaying turn list automatically on freeway:
IRG0113
1. Highlight the exit where the exit information icon is displayed, and push
<ENTER>. The category list screen is displayed.
IRG0115
3. Highlight the preferred facility for the waypoint and push <ENTER>.
IRG0112
When [Auto. Show Turn List on Freeway] is set to ON, the turn list will be automatically displayed while the vehicle travels on a freeway or toll road.
Selecting a waypoint from the exit information list:
When exit information is displayed on the turn list, a waypoint to a facility located near the freeway exit can be set as a waypoint.
IRG0114
2. Highlight the landmark category and push <ENTER>. The list screen for showing facilities located near the freeway exit is displayed.
IRG0116
4. The waypoint is set, and the route search is performed.
“Procedures after setting destination” (page 5-2)
5-12
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (103,1)
5. Route guidance
ROUTE SCREEN
WARNING!
GUID-50E81198-C723-4F4C-BD17-4585ECC046CE
Always stop the vehicle in a safe location before modifying the route conditions.
Modifying the route conditions while driving may cause an accident.
During route guidance, the route conditions can be modified and the route information can be confirmed. Set route conditions according to personal preference.
IRG0117
BASIC OPERATION
1. Push <ROUTE>.
2. Highlight the preferred setting item and push <ENTER>.
3. Push <MAP> to return to the current location map screen.
Available setting items
. [Cancel Route/Resume Route]:
Cancels the current route guidance. A canceled route can also be reactivated.
If the suggested route is canceled,
[Cancel Route] changes to [Resume
Route].
“Canceling/reactivating route”
(page 5-14)
. [Edit/Add to Route]:
Edit or add a destination or waypoints to the route that is already set.
“Editing route” (page 5-15)
. [Route Info]:
Confirm the route by the route information or simulation. The confirmed route can also be stored.
“Confirming route” (page 5-20)
. [Guidance Settings]:
Activates or deactivates route, voice guidance and/or traffic announcement and adjust the volume level of voice guidance.
“Guidance settings” (page 5-21)
. [Recalculate]:
Manually search for the route again after changing the search condition and have the system calculate a route.
“Recalculate route” (page 5-22)
. [Detour]:
A detour of a specified distance can be calculated.
“Setting detour route” (page 5-23)
. [Traffic Detour]:
Manually search for an alternative detour route taking the traffic information into consideration.
“Searching for detour route taking traffic information into consideration” (page 5-24)
. [Route Settings]:
Changes the route calculation conditions anywhere along the route.
“Setting conditions for route calculation” (page 5-25)
5-13
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (104,1)
5. Route guidance
CANCELING/REACTIVATING ROUTE
A route that is already set can be canceled at any time. If a route is deleted, the destination and waypoints are also canceled.
It is also possible to reactivate a canceled route.
INFO:
Canceling a route does not delete the destination and waypoint information completely.
“Delete destination” (page 4-24)
Canceling route
IRG0117
1. Push <ROUTE>.
2. Highlight [Cancel Route] and push
<ENTER>.
Reactivating route
IRG0118
3. A confirmation message is displayed.
Highlight [Yes] and push <ENTER>.
The route is canceled along with the destination and waypoints.
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
To cancel a route:
"Cancel Route" (Alternate Command
Mode)
IRG0119
1. Push <ROUTE>.
2. Highlight [Resume Route] and push
<ENTER>.
IRG0120
3. A confirmation message is displayed.
Highlight [Yes] and push <ENTER>. The canceled route is reactivated.
5-14
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (105,1)
5. Route guidance
INFO:
If a new route is set, the canceled route cannot be reactivated.
EDITING ROUTE
IRG0121
1. Push <ROUTE>.
2. Highlight [Edit/Add to Route] and push
<ENTER>.
3. Highlight the preferred condition and push <ENTER>.
4. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
IRG0122
Available setting items
[Add Destination]:
“Setting destination or waypoint”
(page 5-15)
Current destination:
Changes or deletes the destination.
“Editing/deleting destination or waypoint” (page 5-17)
Condition for calculating a route to the destination:
Changes the conditions for calculating a route to the destination.
“Changing route calculation conditions” (page 5-19)
[Add Waypoint]:
“Setting destination or waypoint”
(page 5-15)
Current waypoint:
Changes or deletes the waypoint.
“Editing/deleting destination or waypoint” (page 5-17)
Condition for calculating a route to a waypoint:
Changes the conditions for calculating a route to a waypoint.
“Changing route calculation conditions” (page 5-19)
[Calculate]:
Manually search for the route again after changing the search conditions and have the system calculate a route.
“Changing route calculation conditions” (page 5-19)
Setting destination or waypoint
A destination or waypoint can be added to the route that has already been set. A total of 6 destinations or waypoints can be set.
5-15
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (106,1)
5. Route guidance destination.
“4. Setting destination”
IRG0123
1. Push <ROUTE>.
2. Highlight [Edit/Add to Route] and push
<ENTER>.
3. Highlight [Add Destination] or [Add
Waypoint] and push <ENTER>.
If [Add Destination] is selected, the current destination changes to a waypoint.
IRG0125
5. The selected location is displayed at the center of the map. Highlight [Add to
Route] after confirming the location and push <ENTER>.
INFO:
Even after setting a destination/waypoint, the destination/waypoint location can be adjusted, the route can be stored, etc.
“Editing/deleting destination or waypoint” (page 5-17)
IRG0126
6. Return to the [Edit Route] screen. Set the route conditions as necessary.
7. Highlight [Calculate] and push <ENTER>.
The system will recalculate the routes.
After the route search is completed, the display will automatically return to the current location map screen.
INFO:
. The prior route is automatically deleted.
. Added waypoints and search conditions will not be taken into consideration for the route calculation until [Calculate] is highlighted and <ENTER> is pushed.
IRG0124
4. Set a destination or waypoint. The method of searching for a destination or waypoint is the same as the one for a
5-16
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (107,1)
5. Route guidance
Editing/deleting destination or waypoint
The destination or waypoint that has already been set can be modified or deleted.
If a location is modified or deleted when a suggested route is already set, the prior suggested route will be recalculated accordingly.
IRG0128
4. Highlight [Move Dest.] to modify the location and push <ENTER>.
“Moving location of destination”
(page 5-5)
IRG0130
6. A confirmation message is displayed.
Confirm the contents of the message, highlight [Yes] and push <ENTER>. The destination or waypoint is deleted from the route. Return to the [Edit Route] screen.
IRG0127
1. Push <ROUTE>.
2. Highlight [Edit/Add to Route] and push
<ENTER>.
3. Highlight a destination or waypoint that is already set and push <ENTER>.
IRG0129
5. Highlight [Delete] and push <ENTER> to delete the location.
IRG0131
7. By highlighting [Calculate] and pushing
<ENTER>, the system will recalculate the routes. After the route search is completed, the display will automatically return to the current location map screen.
5-17
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (108,1)
5. Route guidance
INFO:
. If the destination is deleted, the final waypoint of the route becomes the destination.
. Even if the map screen is touched, the same map screen as when [Move Dest.] is selected is displayed.
Changing order of destination and waypoints
The order of a destination and waypoints that have already been set can be changed.
IRG0133
4. Highlight [Change Order] and push
<ENTER>. A list of the destination and waypoints is displayed.
IRG0135
6. A message is displayed and the order of the destination or waypoint is changed.
IRG0132
1. Push <ROUTE>.
2. Highlight [Edit/Add to Route] and push
<ENTER>.
3. Highlight a destination or waypoint that is already set and push <ENTER>.
IRG0134
5. Highlight a preferred destination or waypoint to replace the previously selected destination or waypoint and push <ENTER>.
IRG0136
7. By highlighting [Calculate] and pushing
<ENTER>, the system will recalculate the routes. After the route search is complete, the display will automatically return to the current location map screen.
5-18
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (109,1)
5. Route guidance
Changing route calculation conditions
Each section of the route between waypoints can have different route calculation conditions. After setting these conditions, the entire route can be recalculated.
IRG0137
1. Push <ROUTE>.
2. Highlight [Edit/Add to Route] and push
<ENTER>.
3. Highlight the preferred section of the route to the destination or waypoint and push <ENTER>.
IRG0138
4. Highlight the preferred condition and push <ENTER>.
Available conditions
: [Fastest Route]
: [Minimize Freeway]
: [Shortest Route]
IRG0139
5. The conditions have been changed and the display returns to the [Edit Route] screen.
IRG0140
6. By highlighting [Calculate] and pushing
<ENTER>, the system will recalculate the routes. After the route search is completed, the display will automatically return to the current location map screen.
INFO:
. The recalculated route may not be the shortest route because the system prioritizes roads that are easy to drive for safety reasons.
. If the route conditions are set from [Route
Settings], all sections in the route are subject to the same route conditions. This applies even if different route conditions have been set for different sections in [Edit
Route].
5-19
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (110,1)
5. Route guidance
CONFIRMING ROUTE
When the suggested route is displayed after calculation, the route information can be confirmed or the suggested route can be simulated.
Basic operation
1. Push <ROUTE>.
IRG0141
2. Highlight [Route Info] and push
<ENTER>.
IRG0142
3. Highlight the preferred item and push
<ENTER>.
Available setting items
. [Turn List]:
Displays the details of the suggested route.
“Using turn list” (page 5-20)
. [Preview]:
The system will trace the planned route going forward or in reverse.
“Using route preview” (page 5-21)
. [Simulation]:
Displays a simulation of the suggested route. This function provides a detailed image of the route with voice guidance.
“Confirming route by simulation”
(page 5-21)
. [Store Route]:
Stores a calculated route. A maximum of 5 routes can be stored. Stored routes can be easily retrieved and set as the suggested route.
“Storing route” (page 6-5)
. [Map Scroll]:
Displays a map screen where the location of the destination can be confirmed.
The same screen as when [Map Scroll] is touched can be displayed with the following operations:
— Touching the map screen.
— Pushing the directional buttons except for the up/down buttons (INFINITI controller with directional buttons).
— Pushing the slide switch except in the upward/downward direction (INFINITI controller without directional buttons).
Using turn list
IRG0143
1. Highlight [Turn List] and push <ENTER>.
2. The information (e.g., intersections) can be confirmed on the route to the destination by scrolling the screen pushing the up and down switches of the main directional buttons, pushing the slide switch upward or downward or rotating the center dial.
5-20
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (111,1)
5. Route guidance
3. Push <MAP> to return to the current location map screen.
Using route preview
IRG0144
1. Highlight [Preview] and push <ENTER>.
2. Highlight the preferred key and push
<ENTER>.
: Moves forward in the direction of the destination.
: Moves backward in the direction of the starting point.
/ : Pauses the route preview.
3. Push <MAP> to return to the current location map screen.
INFO:
During the route preview, you can change the map scale by turning the center dial. While the map scale is being changed, the route preview is temporarily stopped.
During the route preview, the map scale can be changed by pushing <ZOOM IN>/<ZOOM OUT> (if so equipped). While the map scale is being changed, the route preview is temporarily stopped.
Confirming route by simulation
INFO:
During the route preview, you can change the map scale by turning the center dial. While the map scale is being changed, the simulation is temporarily stopped.
During the route preview, the map scale can be changed by pushing <ZOOM IN>/<ZOOM OUT> (if so equipped), the simulation is temporarily stopped.
GUIDANCE SETTINGS
Various guidance settings can be set.
Basic operation
1. Push <ROUTE>.
IRG0145
1. Highlight [Simulation] and push
<ENTER>.
2. Highlight the preferred key and push
<ENTER>.
: Pauses the simulation.
: Resumes the simulation.
: Ends the simulation.
3. Push <MAP> to return to the current location map screen.
IRG0146
2. Highlight [Guidance Settings] and push
<ENTER>.
3. Highlight the preferred item and push
<ENTER>.
5-21
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (112,1)
5. Route guidance
4. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
2. After the tone sounds, speak a command.
To turn the Voice Guidance ON or OFF:
“Voice Guidance On/Off” (Alternate
Command Mode)
RECALCULATE ROUTE
A route can be manually searched again after changing the search condition. When the vehicle deviates from the suggested route, the route from the current location to the destination is automatically searched again.
Manually re-searching route
1. Push <ROUTE>.
IRG0149
3. A message is displayed, and the route is recalculated.
IRG0147
Available setting items
. [Guidance Voice]:
Activates or deactivates voice guidance.
The indicator illuminates if voice guidance is activated.
. [Guidance Volume]:
Adjusts the volume level of voice guidance.
. [Traffic Announcement]:
Provides the announcement of a traffic information event on the route.
Voice command
1. Push <TALK wheel.
> located on the steering
5-22
IRG0148
2. Highlight [Recalculate] and push
<ENTER>.
IRG0150
4. Set the route conditions. After finishing the setting, highlight [Start] and push
<ENTER>.
“Procedures after setting destination” (page 5-2)
INFO:
When a waypoint has been set on the route, the system will search for only one route even if
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (113,1)
5. Route guidance route recalculation is performed.
Setting Auto Reroute
1. Push <ROUTE>.
IRG0151
2. Highlight [Route Settings] and push
<ENTER>.
IRG0152
3. Highlight [Other Routing Choices] and push <ENTER>.
IRG0153
4. Highlight [Auto Reroute] and push
<ENTER>. The indicator illuminates.
When the current location map screen or route setting screen is displayed, the system recalculates a route with the set conditions.
“Setting conditions for route calculation” (page 5-25)
SETTING DETOUR ROUTE
To detour from the suggested route, a route detouring for a specified distance can be calculated.
1. Push <ROUTE>.
IRG0154
2. Highlight [Detour] and push <ENTER>.
IRG0155
3. Highlight a detour distance and push
<ENTER>.
After calculating the detour, the system displays the detour route on the map.
INFO:
. When the vehicle has deviated from the suggested route, [Detour] cannot be selected.
5-23
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (114,1)
5. Route guidance
. If the system cannot calculate a detour with the specified conditions, it displays the previous suggested route.
. If the vehicle is traveling very fast, the detour route may start from a location that the vehicle has already passed.
SEARCHING FOR DETOUR ROUTE
TAKING TRAFFIC INFORMATION INTO
CONSIDERATION
When a serious traffic event occurs on the route, or if the system finds a faster route, a detour alert will pop up automatically. If the automatic alert is not noticed, a detour can also be manually searched.
1. Push <ROUTE>.
IRG0156
2. Highlight [Traffic Detour] and push
<ENTER>.
IRG0157
3. When the detour search is successful, detailed information about the detour route (left screen) and the comparison screen of the two routes (right screen) are displayed.
Original route (yellow)
Detour route (pink)
The change of distance and estimated travel time to destination when the detour route is taken.
4. To accept the suggested detour route, highlight [Yes], and then push <ENTER>.
INFO:
. If no route is set, or [Use Real Time Traffic
Information] is turned off, this function cannot be operated.
. If a detour route is not selected and no further action is performed, the detour route will be automatically canceled.
. The detour suggestion can be retrieved even after the message disappears by manually selecting [Traffic Detour]. The system will then search for the detour again and suggests a detour if one is available at that time.
. Without a subscription to a NavTraffic broadcast, it will not be possible to get a traffic detour or apply settings for functions related to traffic information. A message appears when a related menu item is selected.
“Notes on NavTraffic information”
(page 10-14)
Automatic detour guidance
When [Auto Reroute] and [Use Real Time
Traffic Information] are turned on in the detailed route settings, a message will automatically pop up when the system finds a detour.
“Detailed route settings” (page 5-26)
5-24
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (115,1)
5. Route guidance
“Guidance settings” (page 5-21)
SETTING CONDITIONS FOR ROUTE
CALCULATION
Search condition settings
The route can be recalculated after changing the route calculation conditions anywhere along the route.
IRG0158
1. If a traffic jam or a serious traffic problem occurs on the route while driving along the suggested route, the automatic detour route search starts and a message pops up if a detour is found.
2. To accept the suggested detour route, highlight [Yes] and push <ENTER>.
INFO:
. If no operation is performed for one minute after the message is displayed, the message disappears. The detour will not be accepted, and the current suggested route will remain unchanged.
. When [Traffic Announcement] is turned on in the guidance settings, the system will announce voice guidance at the same time that the message appears on the screen.
IRG0159
Basic operation:
1. Push <ROUTE>.
2. Highlight [Route Settings] and push
<ENTER>.
3. Highlight [Basic Route Type] and push
<ENTER>.
4. Highlight the preferred condition and push <ENTER>. The indicator for the selected condition illuminates.
5. When the conditions are set, the system starts calculating the route with the new conditions, and the current location map screen is displayed.
Available conditions
. [Fastest Route]:
Prioritizes by the fastest time.
. [Minimize Freeway]:
Minimizes the use of motorways.
. [Shortest Route]:
Prioritizes by the shortest route.
INFO:
Only one of these conditions can be utilized at a time.
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
To set conditions for the route calculation (Alternate Command Mode):
“Fastest Route”
“Minimize Freeway Route”
5-25
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (116,1)
5. Route guidance
“Shortest Route”
Detailed route settings
Detailed conditions can be set for the route calculation.
IRG0160
Basic operation:
1. Push <ROUTE>.
2. Highlight [Route Settings] and push
<ENTER>.
3. Highlight [Other Routing Choices] and push <ENTER>.
4. Highlight the preferred condition and push <ENTER>. The indicator for the selected condition illuminates.
5. If [Route Settings] is exited after changing the settings, the system starts calculating the route with the new conditions.
Available setting items
. [Minimize Toll Roads]:
Minimizes the use of toll roads.
. [Use Time Restricted Roads]:
Uses any roads subject to time restrictions.
. [Use Statistical Traffic Information]:
Uses statistical traffic information that is stored in the map data.
. [Use Real Time Traffic Information]:
Uses the latest traffic information received via the SiriusXM broadcast.
. [Use Avoid Area Settings]:
Enables the avoid area setting.
. [Use Ferries]:
Includes the use of ferries.
. [Use Learned Routes]:
Uses the roads that are most frequently traveled with the help of self-learning technology.
. [Auto Reroute]:
If the vehicle deviates from the suggested route, the system automatically recalculates a route that leads the vehicle to the suggested route.
5-26
INFO:
. The recalculated route may not be the shortest route because the system prioritizes roads that are easy to drive for safety reasons.
. If route conditions are set from [Route
Settings], all sections in the route are subject to the same route conditions even though different route conditions have been set for different sections in [Edit/Add to
Route].
. If [Use Time Restricted Roads] is deactivated, the system calculates a route without any consideration of the regulations concerning the time or day of the week.
Therefore, the suggested route may include a road subject to traffic regulations concerning the time or day of the week. When driving along the route, always follow all traffic regulations regardless of whether
[Use Time Restricted Roads] is set to on or off.
. If the system cannot calculate any alternative routes, it displays the previous route.
. If the vehicle greatly deviates from the suggested route, the system calculates a new route.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (117,1)
5. Route guidance
. Statistical traffic information is based on previous traffic data. When the traffic situation rapidly changes due to unexpected accidents, construction work, traffic restrictions, emergencies, etc., the prediction accuracy of the system may be reduced.
. Traffic jam information displayed on the map screen is not statistical traffic information.
. When [Use Statistical Traffic Information] is turned on, the system may lead to a road where a traffic jam occurs or to a detour even though the shortest route does not have a traffic jam.
. Even when [Use Real Time Traffic Information] is turned on, if traffic information has not been provided for the area, sometimes it is possible that a detour will not be indicated in a location where a traffic jam occurs.
. The system may not lead to a detour if traffic closure or a traffic jam occurs far from the present location.
. The system calculates to reduce the time required for the entire route from the start to the destination. If there are no appropriate routes, the system may lead to a route where a traffic jam occurs instead of leading to a detour.
. This system can learn and memorize the route that is most frequently used. However, despite driving on the same route several times so that the system can learn the route, the system may have difficulty learning the route under the following conditions.
— [Use Time Restricted Roads] is set to on.
— [Use Real Time Traffic Information] is set to on.
ROUTE GUIDANCE SETTINGS
Various guidance information can be set to be played during route guidance and the route and/or voice guidance can be activated or deactivated.
IRG0161
BASIC OPERATION
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Guidance Settings] and push
<ENTER>.
4. Highlight the preferred item and push
<ENTER>.
5. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
5-27
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (118,1)
5. Route guidance
IRG0162
Available setting items
. [Guidance Volume]:
Adjusts the volume level of voice guidance.
“Guidance settings” (page 5-21)
. [Guidance Voice]:
Activates or deactivates voice guidance.
The indicator illuminates if voice guidance is activated.
“Guidance settings” (page 5-21)
. [Traffic Announcement]:
Provides an announcement of a traffic information event on the route.
“Guidance settings” (page 5-21)
. [Voice Guidance Settings]:
Sets advanced settings for the voice guidance announced at guide points.
“Route guidance settings”
(page 5-27)
5-28
. [Guidance Display Settings]:
Activates or deactivates small turn arrow display on the map.
“Displaying small turn arrow on map” (page 5-29)
. [Estimated Time]:
Switches the display of the estimated travel time to the destination or waypoint that is displayed on the map screen.
“Switching estimated arrival time display” (page 5-29)
. [Others]:
— [Set Average Speeds]:
Sets an average vehicle speed for each type of road, which is reflected in the calculation of the required time to the destination.
“Set average speeds” (page 5-30)
— [Auto Reroute]:
If the vehicle deviates from the suggested route, the system automatically recalculates a route that leads the vehicle to the suggested route.
“Setting Auto Reroute” (page 5-23)
SETTING VOICE GUIDANCE AT IN-
TERSECTIONS
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Guidance Settings] and push
<ENTER>.
IRG0163
4. Highlight [Voice Guidance Settings] and push <ENTER>.
IRG0164
5. Highlight [Intersection Guidance Settings] and push <ENTER>.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (119,1)
5. Route guidance
IRG0165
6. Highlight the preferred item and push
<ENTER>.
Available setting items
. [Voice Announcements]:
Sets how many times the voice guidance is announced before the vehicle reaches an intersection.
1. Highlight [Voice Announcements] and push <ENTER>.
2. Highlight the preferred item and push
<ENTER>.
.
[Full]:
The system announces three kinds of voice guidance: “Turning Point”,
“1 Guide” and “2 Guide”.
.
[Concise]:
The system announces two kinds of voice guidance: “Turning Point” and
“1 Guide”.
. [Turning Point]:
Turns on the sound that chimes when a maneuver is supposed to be occurring.
DISPLAYING SMALL TURN ARROW
ON MAP
The guidance screen displayed when the vehicle passes through an intersection can be changed.
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Guidance Settings] and push
<ENTER>.
IRG0166
4. Highlight [Guidance Display Settings] and push <ENTER>.
IRG0167
5. Highlight [Small Turn Arrow on Map] and push <ENTER> to activate or deactivate Small Turn Arrow on the Map
(simplified turn indicator) displayed in the upper left corner of the map screen.
The indicator illuminates if the Small
Turn Arrow on the Map is displayed.
SWITCHING ESTIMATED ARRIVAL
TIME DISPLAY
The display of the travel time on the map screen can be switched between the travel time to the destination and the travel time to the waypoint.
Example: Switching the display to the travel time to the waypoint
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
5-29
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (120,1)
5. Route guidance
3. Highlight [Guidance Settings] and push
<ENTER>.
IRG0168
4. Highlight [Estimated Time] and push
<ENTER>.
IRG0169
5. Highlight [Waypoint] and push <ENTER>.
The indicator for the selected condition illuminates.
6. Push <MAP> to return to the current location map screen.
IRG0170
7. The icon displayed on the map screen is switched, and the travel time to the waypoint is displayed.
Displayed icon
: Display of the travel time to the destination
: Display of the travel time to the waypoint
SET AVERAGE SPEEDS
The required time to the destination can be calculated based on the set vehicle speeds.
Basic operation
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Guidance Settings] and push
<ENTER>.
4. Highlight [Others] and push <ENTER>.
5. Highlight [Set Average Speeds] and push <ENTER>.
6. Highlight the preferred item and push
<ENTER>.
7. Use the INFINITI controller to make an adjustment. The speed can be increased/decreased by 5 MPH (5 km/h).
8. After finishing the setting, push
<ENTER> or <BACK> to activate the setting.
9. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
IRG0172
Available setting items
. [Auto]:
If set to ON, the system automatically calculates the required time to the destination, the indicator illuminates
5-30
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (121,1)
5. Route guidance and the speed settings cannot be changed.
. [Freeway]:
Adjust the average vehicle speed on a freeway by moving the INFINITI controller in the direction of [+] or [-].
. [Main Road]:
Adjust the average vehicle speed on a main road by moving the INFINITI controller in the direction of [+] or [-].
. [Town Road]:
Adjust the average vehicle speed on a town road by moving the INFINITI controller in the direction of [+] or [-].
. [Residential]:
Adjust the average vehicle speed in a residential area by moving the INFINITI controller in the direction of [+] or [-].
. [Reset]:
Sets the average vehicle speeds to the default values.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
5-31
Black plate (122,1)
5. Route guidance
MEMO
5-32
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
6 Storing location/route
Black plate (123,1)
Transferring information to/from
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (124,1)
6. Storing location/route
STORING LOCATION
Often visited locations can be stored in the
Address Book. The stored addresses can be easily retrieved to set them as a destination or waypoint.
INFO:
. The Address Book can store up to 300 locations.
. New information placed in the same storage position will overwrite the old data.
STORING LOCATION BY SEARCHING
After a location is searched for once, it can be stored for future use.
1. Push <SETTING>.
5. Highlight [Home Location (None)] or
[Add New] and push <ENTER>.
IST0082
3. Highlight [Address Book] and push
<ENTER>.
IST0085
6. Highlight the appropriate method to search for a location and push <ENTER>.
“4. Setting destination”
IST0083
4. Highlight [Stored Location] and push
<ENTER>.
IST0081
2. Highlight [Navigation] and push
<ENTER>.
6-2
IST0084
IST0086
7. When a preferred location is displayed at the center of the map, confirm the address of the location and push
<ENTER>.
A message is displayed, and the address of the location is stored in the Address Book.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (125,1)
6. Storing location/route
Other settings
An address can also be stored using the following procedure.
STORING CURRENT VEHICLE LOCA-
TION
IST0087
8. Adjust the location of the stored item and edit the contents of the stored item as necessary. After finishing the setting, highlight [OK] and push
<ENTER>.
INFO:
. When the location is stored in the Address
Book, [Address Book] can be used to search for the location.
. A location can be adjusted by selecting
[Move Location] using the same method as the one for a destination.
“Moving location of destination”
(page 5-5)
IST0088
1. Push <DEST>.
2. Highlight [Address Book] and push
<ENTER>.
3. Highlight [Store/Edit] and push
<ENTER>.
4. Highlight [Add New] and push <ENTER>.
5. Highlight the appropriate method to search for a location and push <ENTER>.
The address of the searched location is stored.
“4. Setting destination”
IST0089
1. Push <MAP> to display the current location map screen.
2. Push <ENTER> at the current vehicle location.
IST0090
3. Highlight [Store Location] and push
<ENTER>. A message is displayed, and the current vehicle location is stored in the Address Book.
6-3
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (126,1)
6. Storing location/route
1. Move to the preferred location on the map and push <ENTER>.
INFO:
The address is stored in the first available position number in the Address Book list.
IST0091
4. The icon representing the stored location is displayed on the map.
Push <MAP> or <BACK> to return to the current location map screen.
INFO:
The location is stored in the first available position number in the Address Book list.
STORING LOCATION BY MOVING
MAP
IST0093
2. Highlight [Store Location] and push
<ENTER>. A message is displayed, and the address of the location is stored in the Address Book.
IST0092
IST0094
3. The icon representing the stored location is displayed on the map.
Push <MAP> to return to the current location map screen.
6-4
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (127,1)
6. Storing location/route
STORING ROUTE
A maximum of 5 calculated routes can be stored. Stored routes can be easily retrieved and set as the suggested route.
INFO:
Stored route includes only locations (destination and waypoints) and route calculation conditions, not the route itself.
1. Push <ROUTE>.
IST0095
2. Highlight [Route Info] and push
<ENTER>.
OTHER SETTINGS
A route can also be stored using the following procedure.
IST0096
3. Highlight [Store Route] and push
<ENTER>.
IST0097
4. A confirmation message is displayed.
Confirm the contents of the message, highlight [Yes] and push <ENTER>.
The current route is stored.
IST0098
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Address Book] and push
<ENTER>.
4. Highlight [Stored Routes] and push
<ENTER>.
5. Highlight [Store Current Route] and push <ENTER>.
6. A confirmation message is displayed.
Confirm the contents of the message, highlight [Yes] and push <ENTER>. The current route is stored.
6-5
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (128,1)
6. Storing location/route
INFO:
. The route is stored in the first available position number in the store current route list.
. A maximum of 5 routes can be stored. When
5 routes are stored in the Address Book, a new route cannot be stored until a route is deleted.
“Deleting stored item” (page 6-19)
. If any waypoints are not set on the route, the route cannot be stored.
STORING TRACKED ROUTE
A travelled route up to the current location can be stored. A maximum of 5 tracked routes can be stored.
IST0099
1. Push <MAP> to display the current location map screen.
2. Push <ENTER> at the current vehicle location.
IST0100
3. Highlight [Store Tracking] and push
<ENTER>.
IST0101
4. A confirmation message is displayed.
Confirm the contents of the message, highlight [Yes] and push <ENTER>.
The tracked route you have traveled is stored.
5. Push <MAP> or <BACK> to return to the current location map screen.
INFO:
. A maximum of 5 tracked routes can be stored. When 5 tracked routes are stored in the Address Book, a new tracked route cannot be stored until a tracked route is deleted.
“Deleting stored item” (page 6-19)
. The tracked route is stored in the first available position number in the store tracking list.
6-6
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (129,1)
6. Storing location/route
OTHER SETTINGS
A tracked route can also be stored using the following procedure.
STORING AVOID AREA
An Avoid Area can be stored.
The Avoid Area is an area that can be excluded from a route, such as a road that is always congested. Once Avoid Areas are stored, the system avoids those areas when calculating a route. Up to 10 Avoid
Areas can be stored.
1. Push <SETTING>.
IST0082
3. Highlight [Address Book] and push
<ENTER>.
IST0102
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Address Book] and push
<ENTER>.
4. Highlight [Stored Tracking] and push
<ENTER>.
5. Highlight [Add New] and push <ENTER>.
INFO:
A tracked route can only be stored using the setting screen when [Current Tracking] is set to on.
IST0081
2. Highlight [Navigation] and push
<ENTER>.
IST0103
4. Highlight [Avoid Area] and push
<ENTER>.
IST0104
6-7
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (130,1)
6. Storing location/route
5. Highlight [Add New] and push <ENTER>.
INFO:
A maximum of 10 Avoid Areas can be stored.
When 10 Avoid Areas are already stored, a new Avoid Area cannot be stored until a currently stored Avoid Area is deleted.
“Deleting stored item” (page 6-19)
IST0105
6. Highlight the appropriate method to search for a location and push <ENTER>.
“4. Setting destination”
7. Set the following items for the searched location.
.
Available setting items:
[Rename]:
Changes the name.
“Rename” (page 6-17)
.
[Move Location]:
Adjusts the location of the Avoid
Area.
“Move Location” (page 6-17)
.
.
[Resize Area]:
Adjusts the range of the Avoid Area.
“Resize Area” (page 6-17)
[FWY]:
Avoids Freeways.
“FWY” (page 6-18)
.
[Delete]:
Deletes the avoid area.
“Delete” (page 6-18)
8. After finishing the setting, highlight
[OK] and push <ENTER>.
EDITING ADDRESS BOOK
Items stored in the Address Book can be modified. These settings can be edited to make the navigation system more useful.
IST0107
BASIC OPERATION
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Address Book] and push
<ENTER>.
4. Highlight the preferred item and push
<ENTER>.
Available setting items
. [Stored Location]:
Edits the information of a stored home and Address.
“Editing stored home and address” (page 6-9)
IST0106
6-8
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (131,1)
6. Storing location/route
. [Stored Routes]:
Edits the information of a stored route.
“Editing stored route” (page 6-14)
. [Stored Tracking]:
Edits the information of a stored tracked route.
“Editing stored tracking”
(page 6-15)
. [Avoid Area]:
Edits the information of a stored Avoid
Area.
“Editing avoid area” (page 6-16)
. [Delete Stored Items]:
Deletes a stored location or route.
“Deleting all stored items”
(page 6-20)
. [Transfer Address Book]:
Imports or exports the data of the stored items using a USB memory.
EDITING STORED HOME AND AD-
DRESS
IST0108
1. Highlight [Stored Location] and push
<ENTER>.
2. Highlight the stored home location or preferred stored address and push
<ENTER>.
INFO:
Highlighting [Sort] displays a list of various sort functions.
To use the sort functions, stored locations must be set in advance.
“Minor adjustment of home or stored address” (page 6-10)
IST0109
3. Highlight the preferred item and push
<ENTER>.
Available setting items
. [Edit]:
Edits the stored address information.
. [Move Location]:
Adjusts the location of the stored address.
. [Delete]:
Deletes the stored address.
. [OK]:
Applies the settings.
Other settings
A stored address can also be edited using the following procedure.
6-9
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (132,1)
6. Storing location/route
IST0110
1. Push <DEST>.
2. Highlight [Address Book] and push
<ENTER>.
3. Highlight [Store/Edit] and push
<ENTER>.
MINOR ADJUSTMENT OF HOME OR
STORED ADDRESS
When [Edit] is selected, you can edit the following items of the home or stored location can be edited.
. [Show Icon on Map]
. [Name] (only for stored locations)
. [Voicetag] (only for stored locations)
. [Icon]
. [Sound]
. [Direction]
. [Distance]
. [Phone No.]
. [Group] (only for stored locations)
. [Entry Numbers] (only for stored locations)
Show Icon on Map
Displays the home icon or the stored address icon on the map.
Name (only for stored locations)
Changes the name of a stored location.
IST0112
1. Highlight [Name] and push <ENTER>.
A character input screen is displayed.
IST0111
1. Highlight [Show Icon on Map] and push
<ENTER>.
2. The indicator illuminates when the item is set. Then the system displays the icon on the map.
IST0113
2. Enter the preferred name for the stored location.
“How to input letters and numbers” (page 2-16)
3. Highlight [OK] and push <ENTER>.
The name is stored.
6-10
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (133,1)
6. Storing location/route
Voicetag (only for stored locations)
Stores the voicetag for the stored location.
The voicetag allows you to set the stored location as a destination using Voice
Recognition.
Icon
Changes the icon of the home or stored address to the preferred one. By changing the icons, the usage of the [By Icon] option of the sort function can be optimized more effectively.
IST0114
1. Highlight [Voicetag] and push <ENTER>.
IST0115
2. Highlight [Store] and push <ENTER>.
IST0116
3. A beep sounds, and the system enters the voice command reception mode.
4. Speak the name/word to be used as
Voicetag.
5. The Voicetag is stored, provided the system recognizes it.
INFO:
. A Voicetag cannot be stored, overwritten or played while driving.
. The Address Book can store up to 100
Voicetags.
. Highlight [Play] to confirm the stored
Voicetag.
. Highlight [Delete] to delete a stored Voicetag.
. If a Voicetag is already stored, select
[Restore] to re-record the Voicetag.
1. Highlight [Icon] and push <ENTER>.
IST0117
A list of icons is displayed.
IST0118
2. Highlight the preferred icon and push
<ENTER>.
The icon is changed.
6-11
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (134,1)
6. Storing location/route
Sound
Sets the tone of the alarm that sounds when the vehicle approaches the home or a stored address.
IST0119
1. Highlight [Sound] and push <ENTER>.
A sound list is displayed.
Sound list:
None
Chime
Melody
Sound
Dog
Cat
Wave
Church bell
Marimba
Trumpet
Horn
Scratch
Direction
Sets the alarm to sound when approaching from a specific direction.
1. Highlight [Direction] and push <ENTER>.
A map screen with the home or stored location located on the map center is displayed.
IST0122
2. Set the direction that sounds the alarm and push <ENTER>.
The selected direction is set.
INFO:
After the direction is set and [Direction] is selected and set again, a confirmation message is displayed. Confirm the contents of the message, highlight [Yes] and push <ENTER>.
The set direction is overwritten.
IST0120
2. Select the preferred alarm tone and push <ENTER>.
The indicator of the selected alarm tone illuminates.
IST0121
6-12
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (135,1)
6. Storing location/route
Phone number
Stores the telephone number of the home or a stored location.
Distance
Sets the alarm to sound when reaching a specific distance to the home or stored address.
Available distance options:
. 150 feet (50 m)
. 300 feet (100 m)
. 1000 feet (300 m)
. 1500 feet (500 m)
IST0123
1. Highlight [Distance] and push <ENTER>.
IST0125
1. Highlight [Phone No.] and push
<ENTER>. The telephone number entry screen is displayed.
IST0124
2. Highlight the preferred distance option and push <ENTER>. The indicator of the selected distance illuminates.
IST0191
INFO:
Once the direction and the distance to sound an alarm are set, the system will sound the alarm when the vehicle enters the triggering zone.
Stored location icon
Vehicle icon
Trigger zone
IST0126
2. Enter the telephone number of the home or stored location.
“Number input screen”
(page 2-17)
6-13
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (136,1)
6. Storing location/route
3. Highlight [OK] and push <ENTER>. The telephone number is stored.
INFO:
If the phone number of the home or a location is stored, the phone number can be used to search for the destination even if it is not included in the map data.
Group (only for stored locations)
This groups the stored locations.
By grouping the stored locations, the [By
Group] option of the sort function can be used more effectively in the [Sort Entries] mode.
1. Highlight [Entry Numbers] and push
<ENTER>.
A list of stored locations is displayed.
IST0128
2. Highlight the preferred group and push
<ENTER>.
When the indicator of the selected group illuminates, the stored location is classified into the applicable group.
Entry Numbers (only for stored locations)
Switches the entry numbers of any two stored locations in the list.
IST0130
2. Highlight the stored addresses that you want to change and push <ENTER>.
The position numbers of the selected stored locations are changed.
EDITING STORED ROUTE
IST0127
1. Highlight [Group] and push <ENTER>.
6-14
Condition: Language=NAM_English/
IST0129
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
IST0131
Black plate (137,1)
6. Storing location/route
1. Highlight [Stored Routes] and push
<ENTER>.
2. Highlight the preferred stored route and push <ENTER>.
IST0132
3. Highlight the preferred item to edit from the list on the right side of the screen and push <ENTER>.
4. After finishing the editing, highlight
[OK] and push <ENTER>.
INFO:
If [Store Current Route] is selected, the system stores the current route.
Available setting items
. [Rename]:
Changes the name.
“Character (letters and numbers) input screen” (page 2-16)
. [Replace]:
Overwrites the stored route with the current route.
. [Delete]:
Deletes the stored route.
. [OK]:
Applies the settings.
EDITING STORED TRACKING
IST0133
1. Highlight [Stored Tracking] and push
<ENTER>.
2. Highlight the stored tracked route and push <ENTER>. When the “ON” indicator is not illuminated, push <ENTER>. The indicator illuminates, and the Edit screen is displayed.
If <ENTER> is pushed while the “ON” indicator is illuminated, the indicator turns off.
IST0134
3. Highlight the preferred item and push
<ENTER>.
Available setting items (Current tracking)
. [View Track]:
Displays the tracked route up to the current location.
. [Delete]:
Deletes the stored current tracking.
. [OK]:
Applies the settings.
IST0135
6-15
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (138,1)
6. Storing location/route
Available setting items (Stored tracked routes)
. [View Track]:
Displays a stored tracked route on the map.
. [Rename]:
Changes the name.
“Character (letters and numbers) input screen” (page 2-16)
. [Replace]:
Overwrites the stored tracked route with the current tracked route.
. [Delete]:
Deletes the stored tracked route.
. [OK]:
Applies the settings.
Displaying a tracked route
The stored tracked route can be displayed on the map as necessary.
IST0136
1. Highlight [Stored Tracking] and push
<ENTER>.
2. Highlight a tracked route to display on the map screen, and push <ENTER>. The
“ON” indicator illuminates, and the Edit screen is displayed.
4. Push <MAP> to return to the current location map screen.
INFO:
. Current tracking is displayed up to 6 miles
(10 km).
. Stored tracking is displayed up to 12 miles
(20 km).
EDITING AVOID AREA
IST0137
3. After confirming the location to display the tracked route, highlight [OK] and push <ENTER>. The screen returns to the previous screen.
IST0138
1. Highlight [Avoid Area] and push
<ENTER>.
2. Highlight the preferred Avoid Area and push <ENTER>.
6-16
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (139,1)
6. Storing location/route
IST0139
3. Highlight the preferred items and push
<ENTER>.
.
Available setting items
[Rename]:
Changes the name.
.
.
.
[Move Location]:
Adjusts the location of the Avoid
Area.
[Resize Area]:
Adjusts the range of the Avoid Area.
[FWY]:
Avoids freeways.
.
.
[Delete]:
Deletes the Avoid Area.
[OK]:
Applies the setting.
4. After finishing the setting, highlight
[OK] and push <ENTER>.
INFO:
An Avoid Area can be added by selecting [Add
New].
“Storing avoid area” (page 6-7)
Rename
Changes the name of an Avoid Area.
Move Location
Adjusts the location of the Avoid Area.
IST0140
1. Highlight [Rename] and push <ENTER>.
A character input screen is displayed.
2. Enter the preferred name for the avoid area.
3. Highlight [OK] and push <ENTER>. The name is stored.
IST0141
1. Highlight [Move Location] and push
<ENTER>.
2. Adjust the location of the Avoid Area.
3. After adjusting the location, push
<ENTER>.
Resize Area
Adjusts the range of the Avoid Area.
IST0142
6-17
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (140,1)
6. Storing location/route
1. Highlight [Resize Area] and push
<ENTER>.
2. Highlight the range from 5 available levels.
3. After highlighting the range, push
<ENTER>.
INFO:
Turning the center dial to change the scale of the map.
Push <ZOOM IN>/<ZOOM OUT> (if so equipped) to change the scale of the map.
FWY
Sets the route to avoid freeways.
1. Highlight [Delete] and push <ENTER>.
IST0144
2. The Avoid Area is displayed in green if it includes a freeway or in blue if it does not include a freeway.
INFO:
If the current vehicle location is set to an Avoid
Area, the system will not provide route guidance.
Delete
Deletes the Avoid Area.
IST0146
2. A confirmation message is displayed.
Confirm the contents of the message, highlight [Yes] and push <ENTER>. The stored item is deleted from the Address
Book.
IST0143
1. Highlight [FWY].
To include freeways in the Avoid Area, push <ENTER> to illuminate this indicator.
6-18
Condition: Language=NAM_English/
IST0145
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (141,1)
6. Storing location/route
DELETING STORED ITEM
The locations and routes in the Address
Book can be deleted. Two deletion methods are available: deleting an individual item and deleting all stored items.
NOTE:
Deleted items cannot be restored. Before deleting an item, always make sure that the item is truly not necessary.
DELETING STORED ITEM INDIVIDU-
ALLY
You can delete stored addresses, routes, tracking and avoid areas individually.
IST0148
3. Highlight [Address Book] and push
<ENTER>.
IST0150
5. Highlight the preferred location/route for deletion and push <ENTER>.
IST0147
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
IST0149
Example: [Stored Location] is highlighted.
4. Highlight the preferred item for deletion and push <ENTER>.
IST0151
6. Highlight [Delete] and push <ENTER>.
IST0152
6-19
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (142,1)
6. Storing location/route
7. A confirmation message is displayed.
Confirm the contents of the message, highlight [Yes] and push <ENTER>. The stored item is deleted from the Address
Book.
Other settings
A stored address can also be deleted using the following procedure.
INFO:
This procedure applies only for deleting a stored home or address. A stored route, tracking or avoid area cannot be deleted using this procedure.
DELETING INDIVIDUAL ITEM ON MAP
1. Align the cross pointer over the preferred stored location for deletion by moving on the map. Then push
<ENTER>.
3. A confirmation message is displayed.
Confirm the contents of the message, highlight [Yes] and push <ENTER>.
The stored item is deleted from the
Address Book.
DELETING ALL STORED ITEMS
IST0153
1. Push <DEST>.
2. Highlight [Address Book] and push
<ENTER>.
3. Highlight [Store/Edit] and push
<ENTER>.
4. Highlight [Edit or Delete an Entry] and push <ENTER>.
5. Highlight a preferred address and push
<ENTER>.
“4. Setting destination”
IST0154
2. Highlight [Delete] and push <ENTER>.
IST0155
6-20
IST0156
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
IST0157
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (143,1)
3. Highlight [Address Book] and push
<ENTER>.
IST0158
4. Highlight [Delete Stored Items] and push <ENTER>.
IST0159
5. Highlight the preferred item for deletion and push <ENTER>
.
Items that can be deleted
[Delete Home Location]:
Deletes the home location.
Condition: Language=NAM_English/
6. Storing location/route
.
.
.
.
.
.
.
.
.
.
[Delete Address Book]:
Deletes all stored locations.
[Delete Stored Routes]:
Deletes all stored routes.
[Delete Current Tracking]:
Deletes the current tracked route.
[Delete Stored Tracking]:
Deletes all stored tracked routes.
[Delete Avoid Areas]:
Deletes all stored Avoid Areas.
[Delete Stored Voicetags]:
Deletes all stored Voicetags.
[Delete Connected Search History] (if so equipped):
Delete all search history of Connected Search.
[Delete Previous Destinations]:
Deletes all or one of the previous destinations.
[Delete Previous Start Point]:
Deletes all previous start points.
[Delete Learned Route]:
Deletes all system learned routes.
IST0170
6. A confirmation message is displayed.
Confirm the contents of the message, highlight [Yes] and push <ENTER>. The stored items are deleted from the
Address Book.
INFO:
[Delete Connected Search History] is the feature of Infiniti Connection TM . A subscription is necessary to receive Infiniti Connection services.
Other settings
All stored addresses can also be deleted using the following procedure.
6-21
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (144,1)
6. Storing location/route
IST0171
1. Push <DEST>.
2. Highlight [Address Book] and push
<ENTER>.
3. Highlight [Store/Edit] and push
<ENTER>.
4. Highlight [Delete All Addressbook Entries] and push <ENTER>.
“4. Setting destination”
INFO:
This procedure applies only for deleting a stored home or address. A stored route, tracking or avoid area cannot be deleted using this procedure.
6-22
TRANSFERRING INFORMATION TO/FROM
ADDRESS BOOK
The information of the stored home and addresses can be exported and imported using a USB memory device.
INFO:
A USB memory can be used to transfer data but it is not possible to edit data using a personal computer, etc.
IST0157
3. Highlight [Address Book] and push
<ENTER>.
IST0156
1. Insert a USB memory device and push
<SETTING>.
INFO:
Refer to the vehicle Owner’s Manual for the location of the USB connector.
2. Highlight [Navigation] and push
<ENTER>.
IST0162
4. Highlight [Transfer Address Book] and push <ENTER>.
IST0163
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
5. Highlight [Download Address Book to
USB] or [Download Address Book from
USB] and push <ENTER>.
NOTE:
Do not remove the USB memory until the system completely imports or exports the data.
Black plate (145,1)
6. Storing location/route
IST0164
6. Highlight a stored item. The [ON] indicator illuminates.
IST0166
INFO:
If the USB memory already has the data for a stored address, a confirmation message is displayed. Once overwritten, the original data cannot be recovered.
IST0165
7. Highlight [Download] and push
<ENTER>.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
6-23
Black plate (146,1)
6. Storing location/route
MEMO
6-24
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (147,1)
7 Viewing technical information
Destination weather on suggested
Viewing information about current
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (148,1)
7. Viewing technical information
INFORMATION SCREEN
This screen sets or displays various information that is helpful for using the vehicle safely and comfortably.
Available items include the vehicle information, Infiniti Connection T M (if so equipped), Traffic Info. setup, current location information, GPS information, Voice recognition list and map version.
INFO:
. A NavTraffic subscription is necessary to view Traffic Info.
. [Infiniti Connection] is a feature of Infiniti
Connection. Use of this feature is dependent upon a valid subscription and the telematics device being in operative condition, as well as cellular connectivity, navigation map data and GPS satellite signal reception being available.
JNG0147M
BASIC OPERATION
1. Push <INFO>.
2. Highlight the preferred item and push
<ENTER>.
Available items
. [Infiniti Connection] (if so equipped):
Displays various types of information or receives services by connecting your vehicle to the Infiniti Connection Data
Center.
“Infiniti Connection TM ” (page 7-3)
. [Energy Flow] (if so equipped):
Refer to the vehicle Owner’s Manual.
. [Fuel Economy]:
Refer to the vehicle Owner’s Manual.
. [Tire Pressure] (if so equipped):
Refer to the vehicle Owner’s Manual.
. [Maintenance]:
Refer to the vehicle Owner’s Manual.
. [Traffic Info]:
Allows Traffic Info. setup.
“Viewing available traffic information” (page 7-16)
. [Weather Info]:
Displays weather information.
“Viewing available weather information” (page 7-21)
. [Trip Computer] (if so equipped):
Refer to the vehicle Owner’s Manual.
. [Others]:
— [Where am I?]:
Displays information regarding the current vehicle location.
“Viewing information about current vehicle location” (page 7-15)
— [Map Update]:
Displays the map version and enables updating of the map data.
“Map update” (page 7-30)
— [Navigation Version]:
Displays the current navigation system version.
“Viewing navigation system version information” (page 7-31)
7-2
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (149,1)
7. Viewing technical information
— [GPS Position]:
Displays GPS information regarding the current vehicle location.
“Viewing GPS current location information” (page 7-32)
— [Voice Recognition]:
Displays information on how to use the voice recognition.
“9. Voice recognition”
INFO:
The displayed items vary depending on the options that are equipped on the vehicle.
INFINITI CONNECTION
TM
(if so equipped)
LEGAL DISCLAIMER
Avoid operating Infiniti Connection TM and
Infiniti Connection Plus services in such a way that you are distracted while driving.
Infiniti Connection Subscription Agreement required to enroll.
Beginning on your date of purchase, for a period of time, services are complimentary.
At the expiration of the complimentary period, your credit card (if on file) will be charged and your service will automatically renew in accordance with the terms of your
Infiniti Connection Subscription Agreement.
Services are dependent upon subscription enrollment and the telematics device being in operative condition, cellular connection availability, navigation map data, and GPS satellite signal reception, which can limit the ability to reach Infiniti Connection or to receive support. Requires compatible
GSM/GPRS cellular network. Should the cellular provider terminate or restrict network service, services will not be available.
Under this circumstance, your service may be suspended or terminated without notice and without liability to Nissan, Nissan’s third party service providers, the underlying wireless carrier or any third party beneficiary. In the event a change of telecommunications systems or services becomes necessary, you are solely responsible for replacing, as well as the cost of replacing, any equipment in the vehicle that is necessitated. Terms and conditions of Infiniti Connection Subscription Agreement apply.
INFINITI CONNECTION FEATURES
Infiniti Connection provides various types of information and services by connecting your vehicle to the Infiniti Connection Data
Center and Infiniti Connection Response
Center using TCU (Telematics Communication Unit) installed in your vehicle.
WARNING!
GUID-3351361F-A754-4DC9-B209-4D2EF539E24B
.
Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufacturer regarding the possible influences before use.
.
The TCU antenna is installed inside the upper central part of the instrument panel. An occupant should not get any
7-3
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (150,1)
7. Viewing technical information closer to the antenna than specified by the pacemaker manufacturer. The radio waves from the TCU antenna may adversely affect the operation of the pacemaker while using the Infiniti Connection service.
CAUTION!
GUID-9A1052D7-D86B-4C9B-B119-7A00B7D4303A
Please note that the Automatic Collision
Notification service and Emergency Call function cannot be used in the following conditions:
.
The vehicle moves outside the service area where the TCU (Telematics Communication Unit) is connected to Infiniti
Connection.
.
The vehicle is in a location with poor signal reception such as a tunnel, underground parking, behind a building or in a mountainous area.
.
It may not be possible to make an emergency call in all accidents or emergencies, or if you are in a location without reception.
INFO:
. Infiniti Connection features are dependent upon subscription enrollment and the telematics device being in operative condition, cellular connectivity, navigation map data and GPS satellite signal reception. Terms and conditions of Infiniti Connection Subscription Agreement apply.
. Enrollment is required in order to receive
Infiniti Connection services. The services that can be received vary depending on the plan in which you are enrolled.
. All services can be used free of charge for the first year of ownership.
. After the first year, use of the service will no longer be free of charge. The services that can be received vary depending on the plan to which you subscribe.
. Laws in some communities may restrict the use of “Text-to-Speech.” Check local regulations before using this feature.
Infiniti Connection services may be updated. The latest detailed information is available on the following websites or support line.
Infiniti Connection website: www.infiniticonnection.com (for U.S.) https://canada.infiniticonnection.com
(for Canada)
Infiniti Connection support line:
1-800-334-7858 (for U.S.)
1-855-892-7418 (for Canada)
. Automatic Collision Notification:
TCU (Telematics Communication Unit) generates a signal automatically to the
Infiniti Connection Response Center in the case of an accident severe enough to trigger one of the vehicle’s airbags.
Upon the signal, a Response Specialist receives the vehicle location and customer information and notifies the proper authorities in accordance with established policies and procedures.
. Emergency Call:
Emergency Call feature provides emergency assistance by connecting to an
Response Specialist in case of an emergency by pushing the in‐vehicle
<SOS> button. The Response Specialist provides various assistances depending on the situation
“Emergency support” (page 7-14)
7-4
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (151,1)
7. Viewing technical information
. Enhanced Roadside Assistance:
Enhanced Roadside Assistance allows you to receive assistance from the
Roadside Response Specialist for a non‐emergency incident that requires a towing or third party response service. The service is accessed by touching the IVR (Interactive Voice
Response) soft button on the navigation screen or by pushing the in-vehicle
<SOS> button. Roadside Assistance may also be used in conjunction with the Emergency Assistance service, if warranted.
“Emergency support” (page 7-14)
. My Schedule:
My Schedule feature allows accessing to your personal online Google Calendar TM via the navigation system and displaying the calendar or read out the schedule. This service will also allow you to review your appointments and meetings, and select the meeting location as a destination.
“Viewing information feeds”
(page 7-9)
. Report Stolen Vehicle:
Report Stolen Vehicle feature allows reporting Response Specialists of location information send from a stolen vehicle and the Response Specialists provide that information to local law enforcement agencies to assist in the recovery of a stolen vehicle by authorities.
. Remote Door Lock/Unlock:
Remote Door Lock/Unlock feature allows you to access the vehicle remotely by calling to an Infiniti Connection
Response Specialist or from the Infiniti
Connection website to send lock or unlock commands to the vehicle.
“Connecting to Interactive Voice
Menu” (page 7-10)
. Alarm Notification:
Alarm Notification feature will notify you via the chosen notification method in the Infiniti Connection website when your vehicle alarm system is activated.
. Scheduled Maintenance Notification:
The Maintenance Alert Notification provides vehicle’s mileage data to INFINITI.
INFINIT notifies you the maintenance notifications using this mileage data.
. Maintenance Alert:
Maintenance Alert allows you to receive notifications via the chosen notification method set in the Infiniti Connection website in the case of a vehicle subsystem malfunction. The service is managed through the Infiniti Connection website.
. Destination Assistance:
Destination Assistance helps you to search a destination via the Interactive
Voice Response (IVR) system or a live
Response Specialist by pushing the IVR soft button on the navigation screen.
The IVR system will ask you for name, item or address, etc. to locate your requested point of interest and accesses a third-party service to bring up the most applicable results. A
Response Specialist will ask you if your request is not recognized in the IVR session.
. Destination Send‐to Vehicle:
Destination Send-to-Vehicle feature allows you to find the point of interest information from the latest database within the Infiniti Connection website and download to the vehicle.
7-5
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (152,1)
7. Viewing technical information
. Connected Search:
Connected Search gives you the ability to conduct a point of interest search around the vehicle location via the
Destination menu of the navigation system. This search links to the Infiniti
Connection database which may have destination information more up-todate than your Infiniti hard-drive navigation system.
“Setting by Infiniti Connection TM ”
(page 4-14)
. Drive Zone:
Drive Zone feature allows you to monitor the movement of your vehicle in and out of specified regions. Using the Infiniti Connection website or the
Interactive Voice Response (IVR), you can define a series of allowed or restricted regions, and are then alerted via your chosen notification method when the vehicle enters or leaves a designated region. You can also query the Infiniti Connection website to see a listing of alert notifications received.
. Max Speed Alert:
Max Speed Alert allows you to monitor the speed of your vehicle by receiving
7-6 alerts. You can set the maximum speed via the Infiniti Connection website, and if your vehicle exceeds the specified speed threshold, you will receive a notification via the chosen method.
You can also query the Infiniti Connection website to view a listing of Max
Speed Alert notifications.
. Mobile Information Service (if so equipped):
Mobile Information Service (MIS) delivers information such as the latest news headlines, stock quotes and sports scores set in the Infiniti Connection website to be displayed on your navigation screen or be read out.
“Viewing information feeds”
(page 7-9)
. Infiniti Personal Assistant:
Infiniti Personal Assistant delivers a high‐quality assistant‐like service by providing a quick‐assist program designed to provide immediate information or assistance. Services and features are driver‐centric and enable you to make restaurant, hotel or airline reservations, purchase movie, theater or sporting event tickets, and receive local information based on your requests.
“Connecting to Interactive Voice
Menu” (page 7-10)
. Valet Alert:
Valet Alert notifies you if the vehicle moves outside a 0.2 mile radius of the location set on the Infiniti Connection website. You can activate Valet Alert from the "Voice Menu" and saying
"Valet Alert" when the call is connected.
“Connecting to Interactive Voice
Menu” (page 7-10)
Notice to Bluetooth
®
phone users
Hands-free
The Bluetooth
®
Hands-free phone system will be disabled and not be able to take phone calls while the vehicle is connected to the Infiniti Connection Response Specialists or the emergency support staff at the Infiniti Response Center. This is to avoid various services by Infiniti Connection Response Specialists (such as route guidance) and Infiniti Connection emergency support staff being interrupted by incoming calls. Incoming phone calls received while the vehicle is connected to the
Service Center will not be listed in the call
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (153,1)
7. Viewing technical information history of the Bluetooth
®
Hands-free phone system. However those incoming calls may be listed in the call history of your mobile phone, depending on its capabilities. After disconnecting communication with the Infiniti Connection Response Specialist or Infiniti Connection emergency support staff, check the incoming call history on your mobile phone when it is safe to do so.
Service application
A separately purchased Infiniti Connection subscription is required. For detailed information, contact an INFINITI retailer or refer to the following Infiniti Connection website: www.infiniticonnection.com (for U.S.) https://canada.infiniticonnection.com (for
Canada)
INFO:
If the vehicle is owned by another person and is resold, the subscription for this service must be canceled and all data stored on the device must be deleted.
Operating tips
WARNING!
GUID-D56B9698-6357-41FF-A5C7-FC6C7993EDEA
.
Use the Infiniti Connection services after stopping your vehicle in a safe location.
If you have to use the Infiniti Connection services while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.
.
If you are unable to devote full attention to vehicle operation while talking with the Infiniti Connection services, pull off the road to a safe location and stop your vehicle.
. Do not use the Infiniti Connection service with the engine or the hybrid system stopped. Doing so may discharge the vehicle battery.
. The Infiniti Connection services cannot be used under the following conditions:
— Infiniti Connection subscription has expired.
— The vehicle is outside the area where the cellular network service is receivable.
— The vehicle is in a location with poor signal reception such as tunnels, underground parking garages, behind buildings or in mountainous areas.
— The line is busy.
— The TCU (Telematics Communication
Unit) or other systems of your vehicle are not working properly.
— The Infiniti Connection services network system is disabled.
. Information Feeds download cannot be used when the vehicle is connected to the Infiniti Connection Data Center and
Infiniti Connection Response Center.
. Communication with the Infiniti Connection Data Center is related to the data communication mode and may cause occasional difficulty in receiving signals, and the signal receivable area may be limited compared to regular mobile phones.
. You may hear clicks or experience interruptions while speaking with the
Infiniti Connection Response Specialists. This is due to a shift in the connection zone and is not a malfunction.
7-7
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (154,1)
7. Viewing technical information
. Depending on the line used, the sound volume may decrease. Adjust the volume as necessary.
. Received sounds may be distorted or ambient noise may sound like voices of a crowd. This is due to the use of the digital line and is not a malfunction.
. You may hear your own voice from the speaker when talking with the Infiniti
Connection Response Specialists due to a network disturbance. When this occurs, reconnect the line after a few minutes or at a different location.
. This vehicle incorporates a communication device that is called a TCU (Telematics Communication Unit). The communication connection between this unit and the Infiniti Connection
Data Center allows for various services.
When the system connects to the
Infiniti Connection Data Center, an antenna icon will appear on the screen.
Use the service in a location where the symbol representing good signal reception appears on the screen.
: When the signal reception is good
: When the signal reception is bad
7-8
. The Infiniti Connection service uses the
TCU (Telematics Communication Unit).
Even if the signal strength bar of the invehicle data communication module indicates good reception, connection to the Infiniti Connection Data Center may be disabled. This does not indicate a malfunction. Operate the system again after a few minutes.
BASIC OPERATION
With the Infiniti Connection service, various information can be received and displayed on the screen. The information can also be announced by the system.
1. Push <INFO>.
JNG0147M
2. Highlight [Infiniti Connection] and push
<ENTER>.
JNG0149M
3. Highlight the preferred item and push
<ENTER>.
Available items
. [All Information Feeds]:
Displays a list of available information feeds.
“Viewing information feeds”
(page 7-9)
. [Connect to Voice Menu]:
Connects to the Infiniti Connection
Interactive Voice Menu.
“Connecting to Interactive Voice
Menu” (page 7-10)
. [History]:
Displays a list of Infiniti Connection information that has been used.
“Viewing information feeds history” (page 7-11)
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (155,1)
7. Viewing technical information
. [Sync All Information Feeds]:
Updates the All Information Feeds list.
“Updating All Information Feeds”
(page 7-10)
VIEWING INFORMATION FEEDS
Contents of the various Infiniti Connection information services can be downloaded.
Downloading information feeds
1. Push <INFO>.
2. Highlight [Infiniti Connection] and push
<ENTER>.
JNG0149M
3. Highlight [All Information Feeds] and push <ENTER>. A list screen is displayed.
JNG0150M
4. Highlight the preferred information feeds and push <ENTER>. An information feeds list is displayed. The content is announced by the system (Text-to-
Speech) while the vehicle is being driven, or if parked, you can read the content on the display.
INFO:
. Touch [Stop] during communication with the
Infiniti Connection Data Center to cancel the connection.
. A message is displayed when the communication is disconnected while downloading information due to a poor communication status. Select [Yes] to restart the download.
. Laws in some communities may restrict the use of “Text-to-Speech.” Check local regulations before using this feature.
. Some terminology such as personal names, place names, special terms, symbols, etc.
may not be announced correctly. This is not a malfunction.
. The system will pause announcements when interrupted by the voice guidance given by the navigation system. When the voice guidance finishes, the system will restart the announcement.
. The volume can be adjusted when the system announces the information.
“Volume adjustment” (page 8-11)
. The selected content is read out while the vehicle is being driven, or if parked, you can read the content on the display.
. Content settings can be made using the
Infiniti Connection website. For more details, contact the Infiniti Connection support line at 1-800-334-7858 (for U.S.) /1-855-
892-7418 (for Canada) or refer to the Infiniti
Connection website www.infiniticonnection.
com (for U.S.)/https://canada.infiniticonnection.com (for Canada).
Screen information:
When the information feeds downloaded from the Infiniti Connection Data Center while the vehicle is stopped, the contents
7-9
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (156,1)
7. Viewing technical information of the information are displayed.
1. Push <INFO>.
2. Highlight [Infiniti Connection] and push
<ENTER>.
3. Highlight [Sync All Information Feeds] and push <ENTER>.
7-10
JNG0250X
Contents:
The contents of Infiniti Connection feeds are displayed.
[
[Menu]:
Displays the operation menu.
]/[ ]:
Turns to the next or previous page if the information has a number of contents page.
Other information:
The current page number and number of information items are displayed. If there is location or telephone number information, the indicated icon will be displayed.
JNG0251X
After park the vehicle in a safe location or when highlight [Menu] and push <ENTER> , the operation menu is displayed on the right side of the screen.
INFO:
The availability of the operation menu items differs depending on the contents of the selected information feeds.
UPDATING ALL INFORMATION FEEDS
JNG0161M
JNG0162M
4. A confirmation message is displayed.
Confirm the contents of the message, highlight [Yes] and push <ENTER>.
5. The latest information is sent from the
Infiniti Connection Response Center and an updated list is displayed.
CONNECTING TO INTERACTIVE
VOICE MENU
Various services to support your driving is available by answering Interactive Voice
Menu.
For more details, contact the Infiniti Connection support line at 1-800-334-7858
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (157,1)
7. Viewing technical information
(for U.S.) /1-855-892-7418 (for Canada) or refer to the Infiniti Connection website www.infiniticonnection.com (for U.S.)/ https://canada.infiniticonnection.com (for
Canada).
1. Push <INFO>.
2. Highlight [Infiniti Connection] and push
<ENTER>.
JNG0163M
3. Highlight [Connect to Voice Menu] and push <ENTER>.
4. The system connects to the Infiniti
Connection Response Center and menu options will be announced. Speak your preferred option.
.
Destination Assistance
Set a destination using a Interactive
Voice Response (IVR) system.
.
.
.
Roadside Assistance
Connect to the Roadside Response
Specialist.
Valet Alert
Turns on the Valet Alert function and monitor the vehicle movement in and out of the certain scope.
Personal Assistance
Connects to the Infiniti Connection
Response Specialist.
JNG0187X
INFO:
. You can also connect to an Infiniti Connection Interactive Voice Menu using the IVR soft button * on the map.
INFO:
. After selecting [Connect to Voice Menu] and pushing <ENTER> button, it may take some time until the system initiates connection, depending on the technical environment and whether the TCU (Telematics Communication Unit) is being used by other services.
. To avoid disconnecting the line, do not turn off the engine or hybrid system.
. The Bluetooth
®
Hands-free phone system (if so equipped) will be disabled and it will not be possible to take phone calls while the vehicle is connected to the operators at the
Infiniti Connection Response Center.
“Notice to Bluetooth
®
Hands-free phone users” (page 7-6)
VIEWING INFORMATION FEEDS HIS-
TORY
The information feeds that were previously referred to are displayed.
1. Push <INFO>.
2. Highlight [Infiniti Connection] and push
<ENTER>.
7-11
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (158,1)
7. Viewing technical information
JNG0164M
3. Highlight [History] and push <ENTER>.
JNG0165M
4. Highlight the preferred item and push
<ENTER>.
JNG0166M
5. A history list is displayed. Highlight the preferred information feed.
DELETING INFINITI CONNECTION
HISTORY
1. Push <SETTING>.
2. Highlight [Others] and push <ENTER>.
JNG0168M
3. Highlight [Infiniti Connection] and push
<ENTER>.
JNG0169M
4. Highlight [Delete History Lists] and push <ENTER>.
5. Highlight the preferred item and push
<ENTER>.
Available items:
.
[Delete Information Feed History]:
Delete information feeds history.
.
.
[Delete Voice Menu History]:
Delete history of Interactive Voice
Menu.
[Delete Both]:
Delete all history of Infiniti Connection
6. A confirmation message is displayed.
Confirm the contents of the message, highlight [Yes] and push <ENTER>.
7-12
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (159,1)
7. Viewing technical information
INITIALIZING ALL INFINITI CONNEC-
TION SETTINGS
All Infiniti Connection settings are returned to the default settings.
1. Push <SETTING>.
2. Highlight [Others] and push <ENTER>.
JNG0168M
3. Highlight [Infiniti Connection] and push
<ENTER>.
JNG0175M
5. Confirm the contents of message, highlight [Yes] and push <ENTER>.
DISPLAYING UNIT ID INFORMATION
The necessary information for user registration is displayed.
1. Push <SETTING>.
2. Highlight [Others] and push <ENTER>.
JNG0176M
4. Highlight [Unit ID Information] and push <ENTER>.
JNG0177M
5. The Unit ID, TCU (Telematics Communication Unit) ID, SIM ID and VIN
Information necessary for user registration is displayed.
JNG0174M
4. Highlight [Reset All Infiniti Connection
Settings] and push <ENTER>. A confirmation message is displayed.
JNG0168M
3. Highlight [Infiniti Connection] and push<ENTER>.
7-13
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (160,1)
7. Viewing technical information
VOLUME SETTING
The Infiniti Connection Text-to-Speech and
Infiniti Connection Response Specialist volume can be set.
EMERGENCY SUPPORT
Infiniti Connection provides various services to support dealing with emergencies of the subscribed vehicle and the driver.
For example, in case of an illness or serious injury, you can seek support by pushing the in-vehicle <SOS> button and connecting to the Infiniti Connection Response Center. The Infiniti Connection
Response Center can specify the location of the vehicle via GPS, and the information will be sent to the police or other agencies as needed.
For information about other Infiniti Connection emergency support related services, contact the Infiniti Connection support line at 1-800-334-7858 (for U.S.)
/1-855-892-7418 (for Canada) or refer to the Infiniti Connection website www.infiniticonnection.com (for U.S.)/https://canada.infiniticonnection.com (for Canada).
CAUTION!
GUID-BA450A5A-1C21-4C29-B306-4BD13E19D061
.
It may not be possible to make an emergency call in all accidents or emergencies.
.
Park the vehicle in a safe location and set the parking brake before operating
<SOS>.
.
Only use this service in case of an emergency. There may be a penalty for inappropriate use of the service.
.
The emergency support function cannot be used in the following conditions:
— The vehicle moves outside the service area where the TCU (Telematics Communication Unit) is connected to the system.
— The vehicle is in a location with poor signal reception such as a tunnel, underground parking, behind a building or in a mountainous area.
Making an emergency call
JNG0179X
1. Push <SOS> .
2. When the line is connected, speak to the Response Specialist.
INFO:
. After <SOS> is pushed, it may take some time until the system initiates connection, depending on the technical environment and whether the TCU (Telematics Communication Unit) is being used by other services.
7-14
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (161,1)
. An indicator light on <SOS> shows the readiness of the emergency support system.
If the indicator light is not illuminated, pushing <SOS> does not connect your vehicle to the Response Specialist.
The indicator light blinks while connected to the Infiniti Connection Response Center.
. Even when the indicator light is illuminated, connection to the Infiniti Connection Response Center may not be possible. In such cases contact with the police or other agencies should be made using other devices such as telephones.
. To avoid disconnecting the line, do not turn off the engine or hybrid system.
. The Bluetooth
®
Hands-free phone system will be disabled and it is not possible to take phone calls while the vehicle is connected to the emergency support staff at the Infiniti Connection Response Center.
“Notice to Bluetooth
®
Hands-free phone users” (page 7-6)
VIEWING INFORMATION ABOUT CUR-
RENT VEHICLE LOCATION
This displays the information about the vehicle location on the route when driving according to route guidance.
IIN0042
BASIC OPERATION
1. Push <INFO>.
2. Highlight the preferred item and push
<ENTER>.
3. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
Contents of vehicle location information
Next Street:
Displays the next street on the route.
7. Viewing technical information
Current Street:
Displays the current street on the route.
Previous Street:
Displays the previous street on the route.
Displays the distance to the next intersection on the route.
Displays the distance traveled from the previous intersection on the route.
7-15
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (162,1)
7. Viewing technical information
VIEWING AVAILABLE TRAFFIC INFORMA-
TION
NavTraffic information is a subscription service offered by SiriusXM Satellite Radio.
This service provides real-time information regarding traffic flow, accidents, road construction and other incidents, where available.
NavTraffic combines information from commercial and public traffic data providers including government departments of transportation, police, emergency services, road sensors, cameras and aircraft reports.
The traffic information is broadcast to the vehicle by the SiriusXM satellites. Available traffic information on the route the driver selected is shown on the navigation screen so traffic conditions between you and the destination are known. Three types of real-time traffic information for major roadways are shown on the navigation system:
* Unscheduled traffic data for example, accidents and disabled vehicles.
* Scheduled traffic data, for example road construction and road closures.
* Traffic flow information (rate of speed
7-16 data).
WARNING!
GUID-0D7AEC02-62FF-416C-89A0-968695B209B8
NavTraffic information is not a substitute for attentive driving. Traffic conditions change constantly and emergency situations can arise without warning. Relying only on
NavTraffic information may lead to a collision and could result in serious personal injury.
NOTE:
Flow information is provided only for roads equipped with traffic sensors and is not available in all markets covered by the service.
Flow data may not be available on portions of a road that is under construction.
NavTraffic information is available in limited markets. To subscribe or to check if this service is available in the area: call 1-866-635-2349 or see www.siriusxm.
com/navtraffic
INFO:
If a contract is not completed for NavTraffic traffic information service, a message appears, and it will not be possible to check the information on the traffic information system.
JNG0183X
BASIC OPERATION
1. Push <INFO>.
2. Highlight [Traffic Info] and push
<ENTER>.
3. Highlight the preferred information and push <ENTER>.
4. Push <BACK> to return to the previous screen.
Push <MAP> to return to the current location map screen.
Available items
. [Info on Route]:
Displays the list of traffic information found on the recommended route from the current vehicle location to the destination.
. [Nearby Traffic Info]:
Displays the list of traffic information
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (163,1)
7. Viewing technical information around the current vehicle location.
INFO ON ROUTE
This is only available when a route is set.
The list of traffic information found on the recommended route from the current vehicle location to the destination is displayed. The detailed information about displayed events can also be checked.
2. Highlight the event to check the detailed information, and push <ENTER>.
IIN0044
1. Highlight [Info on Route] and push
<ENTER>. A list screen is displayed.
IIN0046
3. The map screen centered around the selected event is displayed. On the left screen, the detailed information about the event is displayed.
The message can be scrolled using the
INFINITI controller or the steering wheel.
4. Push <BACK> to return to the previous screen.
NEARBY TRAFFIC INFO.
The list of available traffic information around the current vehicle location is displayed.
IIN0047
1. Highlight [Nearby Traffic Info] and push
<ENTER>. A list screen is displayed.
IIN0048
2. Highlight the event to check the detailed information for and push
<ENTER>.
IIN0045
7-17
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
7-18
Condition: Language=NAM_English/
Black plate (164,1)
7. Viewing technical information
IIN0049
3. The map screen centered around the selected event is displayed. On the left screen, the detailed information about the event is displayed. The message can be scrolled using the INFINITI controller or the steering wheel.
4. Push <BACK> to return to the previous screen.
DISPLAY URGENT TRAFFIC INFOR-
MATION
When an urgent event is found around the current vehicle location, a message pops up automatically with a voice announcement.
IIN0050
The message includes the icon, event type, event information and the direct distance from the current location to the event.
INFO:
. Urgent traffic information is displayed regardless of whether the traffic information system is on or off.
. When there are multiple urgent events, the event with the shortest direct distance from the current location is displayed.
. If the urgent event is on the recommended route, and if a detour is found, the detour route notification screen is displayed when the vehicle approaches the detour point.
TRAFFIC INFORMATION ON MAP
With subscription to NavTraffic service, traffic information is displayed on both
Plan View and Birdview TM map screen.
“Notes on NavTraffic information”
(page 10-14)
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (165,1)
Screen information
Road conditions
Free Flow: (Green)
Moderate traffic: (Yellow)
Heavy traffic: (Red)
Section affected by serious traffic event:
(Purple)
Estimated travel time to destination calculated with consideration of traffic information on route.
Condition: Language=NAM_English/
7. Viewing technical information
JNG0185X
Traffic information icon:
If the route is not already set, all of the traffic information icons on the map screen are displayed in color. When the route is already set, the icons on the route are displayed in color, and the icons outside the route are displayed in gray.
: Accident
: Closed road
: Information
: Road work
: Slippery road
: Weather
: Incident
Traffic indicator:
Displays the reception condition of traffic information transmitted from the provider.
Green: Reception condition is good.
Gray: Reception condition is not good.
No mark: Subscription to NavTraffic service is not detected.
Traffic information display and scale levels
2D map and Birdview Map
5 miles
2 miles
10 km
4 km
1 mile
1/2 mile
2 km
1 km
1/4 mile
1/8 mile
500 m
200 m
7-19
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (166,1)
7. Viewing technical information
1/16 mile
1/32 mile
1/64 mile
100 m
50 m
25 m
Checking detailed information for traffic information icons on map
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Traffic Info Settings] and push <ENTER>.
IIN0052
1. Place the cross pointer over the traffic information icon. The general description of the icon is displayed.
2. Push <ENTER> or touch [Detail]. The screen for showing the detailed information for the traffic information icon is displayed.
IIN0053
3. The map screen centered around the selected event is displayed. On the left screen, the detailed information about the event is displayed. You can scroll the message by using the INFINITI controller or the steering wheel.
4. Push <MAP> to return to the current location map screen.
TRAFFIC INFORMATION SETTINGS
This displays or changes the settings for the traffic information related functions.
IIN0055
4. Highlight the preferred setting and push <ENTER>. The indicator for the selected setting illuminates.
Available setting items
. Use Traffic Info.:
Enables all traffic information related functions.
. Show Incidents on Map:
Displays the traffic incidents (e.g., accident) on the map screen.
. Show Traffic Flow on Map:
Displays the traffic flow with an arrow on the map screen.
IIN0054
7-20
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (167,1)
. Blink Red Traffic Flow:
Blinks the red traffic flow lines that represent congestions.
. Traffic Announcements:
Announces the traffic information event on the route.
INFO:
. Even when “Show Traffic Flow on Map” and
“Show Incidents on Map” are set to off, the list display of “Info on Route” and “Nearby
Traffic Info” will not be affected.
. Even when “Traffic Announcement” is set to off, the route guidance will not be affected.
Also, the announcement of emergency information and weather information will not be turned off.
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
To turn on or off the traffic information system:
“Information” “Traffic Information”
Condition: Language=NAM_English/
7. Viewing technical information
(Standard Mode)
“Traffic Information” (Alternate Command Mode)
VIEWING AVAILABLE WEATHER INFOR-
MATION
NavWeatherXM information is a subscription service offered by SiriusXM Satellite
Radio.
This service provides real-time information regarding current weather, temperature, warnings, road conditions and forecasts where available. The weather information is broadcast to the vehicle by the SiriusXM
Satellite Radio.
The service enables you to view the following information on the navigation system:
*Current weather information icon of the destination on the screen of suggested route
*Detailed weather information and forecasts of an area of interest
*Countrywide and local maps with the current weather, temperature, warnings and road condition information
*List of warning/watches events detected around the current location
*Pop-up messages on the navigation screen with voice announcements when warnings and watches are detected around
7-21
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (168,1)
7. Viewing technical information the current location
WARNING!
GUID-BD315167-249E-4B86-8E38-351CD04B1F27
NavWeatherXM information is not a substitute for attentive driving. Weather conditions change constantly and emergency situations can arise without warning. Relying only on
NavWeatherXM information could result in serious personal injury.
NavWeatherXM information is available in limited markets. To subscribe to or check if this service is available in the area, call 1-
866-635-2349 or access www.siriusxm.
com/navweather.
INFO:
. If a contract is not completed for the
NavWeatherXM information service, a message appears and it will not be possible to check the information on the traffic information system.
. The weather information is available only for areas that provide weather information to
NavWeatherXM.
IIN0056
INFO:
The reception condition of the SiriusXM Weather information transmitted from the provider can be confirmed using the “Weather” indicator on the upper right side of the screen.
Green: The reception condition is good.
Gray: The reception condition is not good.
No mark: A subscription to the NavWeatherXM service is not detected.
DISPLAYING WEATHER INFORMA-
TION SCREEN
JNG0186X
Basic Operation
1. Push <INFO>.
2. Highlight [Weather Info] and push
<ENTER>.
3. Highlight the preferred information and push <ENTER>.
4. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
Available items
. Current Weather and Forecasts:
Displays current weather information and three-day forecasts.
. Warnings and Watches History:
Displays a list of warnings and watches recently detected around the current
7-22
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (169,1)
7. Viewing technical information location.
. Weather Map:
Displays the current weather map for the preferred area.
. Temperature Map:
Displays the current temperature map for the preferred area.
. Warnings Map:
Displays the current watches/warnings map for the preferred area.
. Road Condition Map:
Displays the current road condition map for the preferred area.
Selecting city
When displaying various weather information screens by pushing <INFO>, the range can be specified for the weather information from among the current location
(local), destination, countrywide (nation) or a specified city.
The city can be specified by selecting one from the list that is displayed.
JNG0186X
1. Push <INFO>.
2. Highlight [Weather Info] and push
<ENTER>.
IIN0090
4. Highlight [Select Other City from Menu] and push <ENTER>.
IIN0060
3. Highlight the preferred information and push <ENTER>.
IIN0058
5. Highlight the preferred state from the list and push <ENTER>.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
IIN0059
7-23
Black plate (170,1)
7. Viewing technical information
6. Highlight the preferred city from the list and push <ENTER>.
INFO:
[Select Other City from Menu] is not available while driving.
Current weather and forecasts
The current weather information and a three-day forecast can be displayed for the current location, the destination or the preferred city.
IIN0060
1. Highlight [Current Weather and Forecasts] and push <ENTER>.
3. A weather information screen is displayed. Highlight [Forecast] and push
<ENTER>.
IIN0061
2. Highlight the preferred area and push
<ENTER>.
.
.
INFO:
[Weather Info on Destination] is not available unless a destination is set for the route guidance.
When a destination is not set, nearby weather information is displayed.
IIN0062
IIN0063
4. The forecast screen is displayed. A three-day forecast can be confirmed for the preferred area.
5. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
Voice command
1. Push <TALK wheel.
> located on the steering
2. After the tone sounds, speak a command.
To display the list for weather information:
“Weather Information” (Alternate Command Mode)
7-24
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (171,1)
Warnings and watches history
A list can be displayed for the warning/ watch events detected around the current location. The detailed information of each event can also be displayed.
7. Viewing technical information
1. Highlight [Weather Map] and push
<ENTER>
IIN0064
1. Highlight [Warnings and Watches History] and push <ENTER>. A list warning/ watch events around the current location is displayed.
IIN0066
3. A screen with detailed information of the event is displayed.
4. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
Weather Map
The current weather map can be confirmed for the current location, the destination, the entire country or the preferred city.
IIN0068
2. Highlight the preferred map area push
<ENTER>
INFO:
[Destination Map] is not available unless a destination is set for the route guidance.
IIN0065
2. Highlight the event to check the detailed information and push <ENTER>.
Condition: Language=NAM_English/
IIN0067
IIN0069
3. A weather map is displayed. The weather and precipitation level are shown by colors.
7-25
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (172,1)
7. Viewing technical information
4. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
Temperature Map
The current temperature map can be confirmed for the current location, the destination, the entire country or the preferred city.
.
.
INFO:
[Destination Map] is not available unless a destination is set for the route guidance.
When a destination is not set, a nearby weather map is displayed.
INFO:
Touch [Legend] to display the map legend.
IIN0070
Voice command
1. Push <TALK> located on the steering wheel.
2. After the tone sounds, speak a command.
To display the list for weather map:
“Weather Map” (Alternate Command
Mode)
IIN0071
1. Highlight [Temperature Map] and push
<ENTER>.
IIN0072
2. Highlight the preferred map area and push <ENTER>.
IIN0073
3. A temperature map is displayed. The temperature information is shown by numbers and colors.
4. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
7-26
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (173,1)
7. Viewing technical information current location map screen.
IIN0074
INFO:
Touch [Legend] to display the map legend.
Warnings Map
The current warning/watch information can be confirmed for the current location, the destination, the entire country or the preferred city.
IIN0076
2. Highlight the preferred map area and push <ENTER>.
INFO:
[Destination Map] is not available unless a destination is set for the route guidance.
IIN0078
INFO:
Touch [Legend] to display the map legend.
Road Condition Map
The current road condition can be confirmed for the current location, the destination, the entire country or the preferred city.
IIN0075
1. Highlight [Warnings Map] and push
<ENTER>.
IIN0077
3. A warning/watch map is displayed.
Warning and watch information is shown by colors.
4. Push <BACK> to return to the previous screen. Push <MAP> to return to the
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
IIN0079
7-27
Black plate (174,1)
7. Viewing technical information
1. Highlight [Road Condition Map] and push <ENTER>.
4. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
displayed via icons.
Weather information icons
Clear
Mostly Clear
Partly Cloudy
Mostly Cloudy
IIN0082
INFO:
Touch [Legend] to display the map legend.
DESTINATION WEATHER ON SUG-
GESTED ROUTE SCREEN
IIN0081
3. A road condition map is displayed. The road conditions are shown by colors.
IIN0083
On the screen of the suggested route after setting a destination, the current weather information around the destination is
7-28
IIN0080
2. Highlight the preferred map area and push <ENTER>.
INFO:
[Destination Map] is not available unless a destination is set for the route guidance.
Cloudy
Haze
Fog
Rain, Light Rain
Hail
Heavy Rain
Freezing Rain/Ice
Snow
Heavy Snow
Dust/Sand
Smoke/Ash
Thunderstorm
/
/
/
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (175,1)
7. Viewing technical information
Tornado/Funnel
Cloud
AUTOMATICALLY DISPLAY WARN-
INGS/WATCHES
When an urgent warning/watch is detected around the current vehicle location, a message pops up automatically with a voice announcement.
starting with the one having the shortest linear distance from the vehicle.
Weather information settings
The settings can be confirmed and changed for the urgent weather information related functions.
IIN0084
The message includes the weather icon and text describing the event.
INFO:
. The pop-up messages and announcements can be set to on or off.
“Weather information settings”
(page 7-29)
. If multiple warning/watch events are detected, they will be displayed in order
IIN0085
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Weather Info Setting] and push <ENTER>.
4. Highlight the preferred setting and push <ENTER>. The indicator for the setting illuminates.
Available setting items
. Display an Alert for Weather Warnings:
Displays a message screen automatically when the system detects urgent warning information.
. Display an Alert for Weather Watches:
Displays a message screen automatically when the system detects urgent watch information.
. Voice Announcements:
Provides urgent information announcements for warnings and watches around the current location.
Types of warnings/watches
Category
Tornado
Hurricane Inland Hurricane Wind, Hurricane
Force Wind, Hurricane, Typhoon
Storm Severe Thunderstorm Watch, Severe
Thunderstorm, Storm, Tropical
Storm, Inland Tropical Storm, Dust
Storm
Flood
Warnings/Watches
Tornado Watch, Tornado
Winter
Flood Watch, Flash Flood, Coastal
Flood, Lakeshore Flood, High Surf,
Flood
Winter Watch, Heavy Snow, Heavy
Sleet, Lake Effect Snow, Freeze,
Heavy Freezing Spray, Blizzard, Ice
Storm, Winter Storm
Wind Wind Watch, High Wind, Wind Chill,
Gale
7-29
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (176,1)
7. Viewing technical information
Category Warnings/Watches
Extremes Excessive Heat
Other Red Flag, Tsunami, Avalanche, Special Marine, Earthquake, Law Enforcement, Hazardous Materials,
Nuclear Power Plant, Radiological
Hazard, Civil Danger, Fire, Shelter in
Place, Volcano, Other Watches,
Other Warnings
INFO:
. The “Other Watches” category in the
“Other” category includes Inland Hurricane
Watch, Hurricane Watch, Typhoon Watch,
Tropical Storm Watch, Inland Tropical Storm
Watch and Fire Weather Watch.
. The “Other Warnings” category in the
“Other” category includes Dense Fog Warning, Freezing Fog Warning, Extreme Cold
Warning, Frost Warning, Hydrologic Warning, Ashfall Warning, Air Stagnation Warning, Low Water Warning, Ice Accretion
Warning, Dense Smoke Warning, Dense
Smoke Advisory, Freezing Fog Advisory,
Dense Fog Advisory, Ashfall Advisory and
Air Stagnation Advisory.
MAP UPDATE
The map database of the navigation system can be updated.
1. Push <INFO>.
IIN0086
2. Highlight [Map Update] and push
<ENTER>.
3. To update the map data, insert the first of the map update DVDs.
IIN0087
4. Highlight [DVD Update] and push
<ENTER>.
7-30
INFO:
. Refer to the vehicle Owner’s Manual for the location of the DVD slot.
. Do not eject the DVD while updating the map data. Doing so will result in an incomplete update.
. Multiple DVDs are required to fully update the system. In addition, a Digital Rights
Management (DRM) activation code is required to complete the installation. To purchase a map update and DRM code, contact the INFINITI NAVIGATION SYSTEM
HELPDESK. See the contact information on the inside front cover of this manual. You will need your Unit ID in order to purchase a map update.
“Viewing navigation system unit identification” (page 7-31)
NOTE:
In handling the DVD-ROM, be careful on the following points.
. Do not try to bend the DVD-ROM. Do not use any disk that is bent or cracked.
. Do not use any benzine, thinner, or antistatic spray on them.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (177,1)
7. Viewing technical information
. Do not put on any sticker or write anything on either surface.
. If you need to clean it, do so with a soft cloth by wiping from the centre outward.
. Do not use a DVD Laser Lens Cleaners as they may cause the DVD player to malfunction.
VIEWING NAVIGATION SYSTEM UNIT
IDENTIFICATION
The navigation system unit identification number and the current map version can be located.
VIEWING NAVIGATION SYSTEM VERSION
INFORMATION
This displays the map version information.
Condition: Language=NAM_English/
IIN0087
BASIC OPERATION
1. Push <INFO>.
2. Highlight [Map Update] and push
<ENTER>.
3. The unit Identification (Unit ID) number is displayed.
4. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
IIN0088
BASIC OPERATION
1. Push <INFO>.
2. Highlight [Navigation Version] and push
<ENTER>.
3. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
“Map update” (page 7-30)
7-31
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (178,1)
7. Viewing technical information
VIEWING GPS CURRENT LOCATION IN-
FORMATION
This displays GPS information, such as the positioning status, latitude/longitude, altitude and satellite locations.
IIN0089
BASIC OPERATION
1. Push <INFO>
2. Highlight [Others] and push <ENTER>.
3. Highlight [GPS Position] and push
<ENTER>.
4. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
Contents of GPS information
GPS Reception:
Displays the GPS positioning method.
3-dimension Calculating the latitude, longitude and altitude by four or more satellites.
2-dimension Calculating the latitude, longitude and altitude by three or more satellites.
Out of range Cannot calculate because no GPS satellites can be located.
Latitude:
Displays the latitude.
Longitude:
Displays the longitude.
Approx Altitude:
Displays the approximate altitude.
Positioning status:
(green)
(gray)
Satellites are available.
Satellites are being searched for.
7-32
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
8 Other settings
Black plate (179,1)
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (180,1)
8. Other settings
SETTINGS SCREEN
The navigation system can be customized to make it easier for you to use.
ISE0059
BASIC OPERATION
1. Push <SETTING>.
2. Highlight the preferred setting item and push <ENTER>.
Available setting items
. [Navigation]:
Adjust various settings of the navigation system.
“Navigation setting” (page 8-5)
. [Audio]:
Refer to the vehicle Owner’s Manual.
. [Phone]:
Refer to the vehicle Owner’s Manual.
. [Bluetooth]:
Set Bluetooth ® Audio and Phone.
Refer to the vehicle Owner’s Manual.
. [Volume & Beeps]:
“Volume adjustment” (page 8-11)
. [Rear Display] (if so equipped):
Refer to the vehicle Owner’s Manual.
. [ECO DRIVE] (if so equipped):
Refer to the vehicle Owner’s Manual.
. [Driver Assistance] (if so equipped):
Refer to the vehicle Owner’s Manual.
. [Others]:
— [Rear Display] (if so equipped):
Refer to the vehicle Owner’s Manual.
— [Display]:
“Display settings” (page 8-3)
— [Comfort]:
This item is displayed when the ignition switch is in the ON position.
Refer to the vehicle Owner’s Manual.
— [Language & Units]:
“Language and unit settings”
(page 8-13)
— [Clock]:
“Clock settings” (page 8-12)
— [Voice Recognition]:
“System feedback announcement modes” (page 9-15)
— [Infiniti Connection] (if so equipped):
“Infiniti Connection TM ” (page 7-3)
— [Camera] (if so equipped):
Refer to the vehicle Owner’s Manual.
— [Sonar] (if so equipped):
Adjust the parking sonar detection sensitivity, etc.
Refer to the vehicle Owner’s Manual.
— [Image Viewer]:
Refer to the vehicle Owner’s Manual.
INFO:
The displayed items vary depending on the equipped options.
8-2
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (181,1)
8. Other settings
DISPLAY SETTINGS
This menu turns on and off the display, adjusts the image quality of the navigation screen and changes the color of the menu screen.
BASIC OPERATION
ISE0052
1. Push <SETTING>.
2. Highlight [Display] and push <ENTER>.
3. Highlight the preferred adjustment item and push <ENTER>.
INFO:
If a rear display is equipped, it is possible to select [Display] after pushing <SETTING>, highlighting [Others] and then pushing <ENTER>.
Available setting items
. [Display Adjustment]
Turn on and off the display and adjust the image quality of the navigation screen.
. [Color Theme]
Set the color of the menu screen.
DISPLAY ADJUSTMENT
This menu turns on and off the display and adjusts the image quality of the navigation screen.
Basic operation
4. After setting, push <ENTER> or <BACK> to apply the setting.
5. Highlight <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
Available setting items
. [Display]:
Turn on or off the screen.
“Display” (page 8-4)
. [Brightness]:
Adjust the screen brightness.
“Brightness” (page 8-4)
. [Contrast]:
Adjust the screen contrast.
“Contrast” (page 8-4)
. [Background Color]:
Set the background color.
“Background color” (page 8-4)
ISE0053
1. Highlight [Display Adjustment] and push <ENTER>.
2. Highlight the preferred adjustment item and push <ENTER>.
3. Use the INFINITI controller to adjust to the preferred setting.
8-3
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
8. Other settings
Display
Black plate (182,1)
Background color Brightness
To turn off the display, push <ENTER>.
ISE0053
The display can also be turned off by pushing and holding <DAY/NIGHT OFF> for more than 2 seconds.
ISE0055
Adjust the display brightness by rotating the center dial in the [+] or [−] direction on the INFINITI controller.
Contrast
ISE0057
Select to toggle between the day screen and night screen.
Day screen
ISE0054
When any button is pushed with the display off, the display turns on. The display will automatically turn off when there is no switch operation for 5 seconds.
To turn on the display, push <DAY/NIGHT
OFF>.
8-4
ISE0056
Adjust the display contrast by rotating the center dial in the [+] or [−] direction on the
INFINITI controller.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
ISE0058
Black plate (183,1)
8. Other settings
NAVIGATION SETTING
The navigation system can be customized to your preferences.
BASIC OPERATION
Night screen ISE0060
INFO:
The background color setting can also be changed using the <DAY/NIGHT OFF>.
SETTING COLOR THEME
ISE0062
2. Highlight the preferred menu color and push <ENTER>.
ISE0061
1. Highlight [Color Theme] and push
<ENTER>.
ISE0063
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight the preferred setting item and push <ENTER>.
Available setting items
. [Address Book]:
Store locations and routes, and edit the stored items.
“Storing location” (page 6-2)
. [Map View]:
Set the display method and the direction of the map.
8-5
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (184,1)
8. Other settings
“Changing map view” (page 3-11)
. [Map Icons]:
Set the map icons to display on the map.
“Displaying map icons”
(page 3-18)
. [Guidance Settings]:
Set the various functions for the route guidance.
“Guidance settings” (page 5-21)
. [Route Settings]:
Change the routing preferences.
“Detailed route settings”
(page 5-26)
. [Traffic Info Settings]:
Set the various functions of the Nav-
Traffic information system.
“Traffic information settings”
(page 7-20)
. [Weather Info Setting]:
Set the functions of the NavWeatherXM information system.
“Weather information settings”
(page 7-29)
. [Speed Limit Info]:
Display speed limit information.
8-6
“Speed limit indication on map”
(page 8-6)
. [Others]:
Display other setting items.
“Other navigation settings”
(page 8-7)
. [Delete Stored Information]:
Delete stored locations and the home setting in the Address Book.
“Delete stored items” (page 8-10)
. [Delete Connected Search History] (if so equipped):
Delete all connected search histories.
“Delete stored items” (page 8-10)
. [Delete All Previous Destinations]:
Delete all previous destinations.
“Delete stored items” (page 8-10)
. [Delete Previous Starting Point]:
Delete all previous starting points.
“Delete stored items” (page 8-10)
. [Reset All Navigation Settings to Default]:
Reset all of the settings to default.
“Reset all navigation settings to default” (page 8-10)
SPEED LIMIT INDICATION ON MAP
Turn the [Speed Limit Info] display on or off. The indicator light illuminates when the speed limit display function is set to on.
ISE0064
1. Highlight [Speed Limit Info] and push
<ENTER>.
ISE0065
2. Highlight [Speed Limit Indication on
Map] to toggle the function between on and off. The indicator light illuminates when the speed limit display function is set to on.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (185,1)
8. Other settings
OTHER NAVIGATION SETTINGS
ISE0066
Basic Operation
1. Push <SETTING>.
2. Highlight [Navigation] and push
<ENTER>.
3. Highlight [Others] and push <ENTER>.
4. Highlight the preferred setting item and push <ENTER>.
Available setting items
. [Audio Display on Map]:
Allows the audio information to be displayed at all times.
“Displaying audio information on map screen” (page 8-7)
. [Small Step Zoom by Dial]:
Sets the free zoom function on or off.
When this setting is on, it is possible to adjust the scale in smaller steps than with normal scale adjustment.
. [Map Scrolling Information]:
Sets the system so that when the map scrolls the information about the location aligned at the center of the cross pointer is displayed.
“Map scrolling information”
(page 3-19)
. [Customize Nearby Places]:
Set the category of frequently visited landmarks.
“Customizing Nearby Places”
(page 8-8)
. [Keyboard Type]:
Switches the keyboard layout for the character input screen.
“Settings keyboard layout of character input screen” (page 8-8)
. [North Up when Zoom Out]:
When this setting is ON, the orientation of the map is automatically changed to
North Up when the widest map scale is selected. The orientation is changed to
North Up even when Heading Up is set.
. [Adjust Current Location]:
Corrects the position of the current location.
“Adjusting current vehicle location” (page 8-9)
Displaying audio information on map screen
The operating status of audio functions can be displayed on the map screen.
ISE0067
1. Highlight [Others] and push <ENTER>.
2. Highlight [Audio Display on Map] and push <ENTER>. The indicator illuminates when the item is set.
3. Push <MAP> to return to the current location map screen.
8-7
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (186,1)
8. Other settings
1. Highlight [Others] and push <ENTER>.
2. Highlight [Customize Nearby Places] and push <ENTER>.
ISE0068
4. On the bottom of the map screen, the operating status of an audio/visual function is displayed at all times.
Customizing Nearby Places
The categories can be customized for searching places of interest nearby.
The modified list of places of interest can be used for searching for a location using
[Places].
“Searching for destinations”
(page 2-21)
ISE0070
3. Highlight the preferred item and push
<ENTER>. The main category list is displayed.
ISE0072
5. Highlight a sub category and push
<ENTER>. The category setting is modified.
6. Push <MAP> to return to the current location map screen.
Settings keyboard layout of character input screen
Depending on the user’s preference for the keyboard layout of character input screen, the ABC layout or QWERTY layout can be selected.
Example: Switching to the QWERTY layout
ISE0071
4. Highlight a main category and push
<ENTER>. The sub category list is displayed. Highlight [Category Search] and push <ENTER>. The preferred category can also be input directly.
ISE0069
8-8
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (187,1)
ISE0073
1. Highlight [Others] and push <ENTER>.
2. Highlight [Keyboard Type] and push
<ENTER>.
ABC layout
8. Other settings
ISE0075
. When correcting the position of the vehicle icon, the map is automatically displayed in the North Up mode. After finishing the correction, the map restores the current orientation setting.
. The position and direction of the vehicle icon may be misaligned depending on the external conditions and environment.
. If the vehicle icon is misaligned, drive for a while in a location where the GPS signals can be received. This may correct the position of the vehicle icon.
“Vehicle icon” (page 11-4)
ISE0074
3. Highlight [QWERTY] and push <ENTER>.
The indicator illuminates when the item is set.
4. Push <MAP> to return to the current location map screen.
QWERTY layout ISE0076
Adjusting current vehicle location
If the vehicle icon indicating the current vehicle location is not in the correct position, the location of the vehicle icon on the map screen can be adjusted.
INFO:
. Regardless of the map view setting, the map is displayed in Plan View when adjusting the position of the vehicle icon.
ISE0077
1. Highlight [Others] and push <ENTER>.
2. Highlight [Adjust Current Location] and push <ENTER>. The current location map screen is displayed.
8-9
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (188,1)
8. Other settings
ISE0078
3. Adjust the position of the vehicle icon.
After adjusting the position of the vehicle icon, push <ENTER>.
ISE0079
4. Adjust the direction of the vehicle icon.
After adjusting the direction of the vehicle icon, push <ENTER>.
ISE0080
5. A message is displayed, and the adjusted vehicle location is stored.
DELETE STORED ITEMS
Delete stored item from setting screen.
Basic Operation
Available items
. [Deletes Stored Information]:
Delete the stored location and home.
. [Deletes Connected Search History] (if so equipped):
Delete the Infiniti Connection history.
TM search
. [Delete All Previous Destinations]:
Delete all previous destinations.
. [Delete Previous Start Point]:
Delete all previous start point.
RESET ALL NAVIGATION SETTINGS
TO DEFAULT
This restores various settings (display, volume level, etc.) to the default settings.
INFO:
The memory contents, such as the stored locations, will not be deleted.
JNH0110X
1. Highlight [Navigation] and push
<ENTER>.
2. Highlight the preferred item that you want to delete and push <ENTER>.
8-10
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (189,1)
8. Other settings
ISE0082
1. Highlight [Navigation] and push
<ENTER>.
2. Highlight [Reset All Navigation Settings to Default] and push <ENTER>.
ISE0083
3. A confirmation message is displayed.
Confirm the contents of the message, highlight [Yes] and push <ENTER>.
VOLUME ADJUSTMENT
This turns on and off, as well as adjusts, the phone function (ringer, incoming and outgoing volume), the voice guide function,
Infiniti Connection function (if so equipped) and the beep function.
BASIC OPERATION
ISE0084
1. Push <SETTING>.
2. Highlight [Volume & Beeps] and push
<ENTER>.
3. Highlight the preferred adjustment item and push <ENTER>.
4. Use the INFINITI controller to adjust the volume. Push <ENTER> to set to on or off.
5. After setting, push <ENTER> or <BACK> to apply the setting.
6. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
Available setting items
. [Audio Volume]:
Adjust the volume level of the audio system using the INFINITI controller in the direction of [+] or [−].
. [Guidance Volume]:
Adjust the volume level of voice guidance using the INFINITI controller in the direction of [+] or [−].
. [Ringtone]:
Adjust the volume level of the ringtone using the INFINITI controller in the direction of [+] or [−].
. [Incoming Call]:
Adjust the incoming call volume using the INFINITI controller in the direction of
[+] or [−].
. [Outgoing Call]:
Adjust the outgoing call volume using the INFINITI controller in the direction of
[+] or [−].
. [Infiniti Connection] (if so equipped):
Adjust the Infiniti Connection volume
8-11
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (190,1)
8. Other settings using the INFINITI controller in the direction of [+] or [−].
. [Switch Beeps]:
Select to toggle the beep function between on and off. The indicator light illuminates when the beep function is set to on. The beep sounds when pushing and holding a button or when a prohibited operation is performed.
. [Guidance Voice]:
Select to toggle the voice guidance function between on and off. The indicator light illuminates when the voice guidance function is set to on.
INFO:
For more details about [Ringtone], [Incoming
Call] and [Outgoing Call], refer to the vehicle
Owner’s Manual.
CLOCK SETTINGS
This changes the clock settings.
BASIC OPERATION
ISE0085
1. Push <SETTING>.
2. Highlight [Clock] and push <ENTER>.
3. Highlight the preferred adjustment item and push <ENTER>.
4. Use the INFINITI controller to adjust to the preferred setting. Push <ENTER> to set on or off.
5. After setting, push <ENTER> or <BACK> to apply the setting.
6. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
Available setting items
. [On-screen Clock]:
Select to toggle the clock display located in the top right corner of the display between on and off. The indicator light illuminates when the clock display is set to on.
. [Clock Format (24h)]:
Select the clock format between 12hour and 24-hour times. The indicator light illuminates when the clock is set to the 24-hour format.
. [Offset (hour)]:
Use the INFINITI controller or the center dial to adjust the offset value (between
−12 and +12).
. [Offset (min)]:
Use the INFINITI controller or the center dial to adjust the offset value (between
−59 and +59).
. [Daylight Savings Time]:
Select to toggle the daylight savings time setting between on and off. The indicator light illuminates when the daylight savings time setting is set to on.
8-12
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (191,1)
8. Other settings
. [Time Zone]:
Select an appropriate time zone from the list that appears when this item is highlighted.
— Pacific
— Mountain
— Central
— Eastern
— Atlantic
— Newfoundland
— Hawaii
— Alaska
LANGUAGE AND UNIT SETTINGS
This changes the language and measurement unit used in the system.
LANGUAGE SETTINGS
4. Highlight [Select Language] and push
<ENTER>.
ISE0086
1. Push <SETTING>.
2. Highlight [Others] and push <ENTER>.
3. Highlight [Language & Units] and push
<ENTER>.
ISE0088
5. Highlight the preferred setting item and push <ENTER>. The indicator light of the selected item illuminates.
.
Available languages
[English]
.
.
[Français]
[Español]
NOTE:
Do not change the ignition switch position while changing the language. Doing so may cause a system malfunction.
ISE0087
8-13
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (192,1)
8. Other settings
UNIT SETTINGS
ISE0086
1. Push <SETTING>.
2. Highlight [Others] and push <ENTER>.
3. Highlight [Language & Units] and push
<ENTER>.
ISE0089
4. Highlight [Select Units] and push
<ENTER>.
ISE0090
5. Highlight the preferred unit and push
<ENTER>. The indicator of the selected unit illuminates.
.
Available units
US: mile, MPH, 8F, MPG
.
Metric: km, km/h, 8C, L/100 km
6. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
INFO:
. [Select Units] and/or [Select Units (Tire
Pressure)] may be displayed depending on the vehicle model and equipment. Refer to the vehicle Owner’s Manual.
8-14
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (193,1)
9 Voice recognition
Displaying how to operate voice
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (194,1)
9. Voice recognition
INFINITI VOICE RECOGNITION
INFINITI Voice Recognition allows handsfree operation of the navigation system and other systems equipped on this vehicle, in one of two modes, Standard
Mode or Alternate Command Mode. Standard Mode allows the operation of Navigation, Phone, Audio, Information and Help.
The commands that are available are always shown on the display and announced by the system. To perform operations, simply follow the prompts given by the system. In Standard Mode, hands-free operation of Change map view, Route selection and Bluetooth Audio, etc. is not available through Voice Recognition.
Alternate Command Mode allows advanced operations. When this mode is active, an expanded list of commands can be spoken after pushing <TALK >, and the voice command menu prompts are turned off.
Note that in this mode the recognition success rate may be affected because the number of available commands and ways of speaking each command are increased.
Otherwise, it is recommended that Alternate Command Mode be turned OFF and
Standard Mode be used for the best
9-2 recognition performance.
“Alternate command mode”
(page 9-9)
INFO:
. For U.S. customers, Standard Mode is selected by default. For Canadian customers, Alternate Command Mode is the default mode.
. To improve recognition success when Alternate Command Mode is active, try using the
Speaker Adaptation function available in that mode.
“Speaker adaptation” (page 9-15)
Otherwise, it is recommended that Alternate
Command Mode be turned OFF and Standard Mode be used for the best recognition performance.
. For the voice commands for the audio, phone and other systems, refer to the vehicle Owner’s Manual. The following sections refer only to the navigation, phone and information systems.
. The voice recognition system cannot be operated when the retractable hard top is not closed (for G37 Convertible only).
STANDARD MODE
CONFIRMING HOW TO USE VOICE
COMMANDS
When operating the voice recognition system for the first time or if help is preferred to use the system, the User
Guide can be displayed.
It is possible to confirm how to use voice commands by accessing a simplified User
Guide, which contains basic instructions and tutorials for several voice commands.
IVR0072
Basic operation
1. Push <INFO>.
2. Highlight [Others] and push <ENTER>.
3. Highlight [Voice Recognition] and push
<ENTER>.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (195,1)
9. Voice recognition
4. Highlight [User Guide] and push
<ENTER>.
5. Highlight the preferred item and push
<ENTER>.
Available items
. [Getting Started]:
Describes the basics of how to operate the voice recognition system.
. [Let’s Practice]:
Mode for practice following the system voice.
. [Using the Address Book]:
Tutorial for entering a destination by the Address Book.
. [Finding a Street Address]:
Tutorial for entering a destination by street address.
. [Placing Calls]:
Tutorial for making a phone call by voice command operation. Refer to the vehicle Owner’s Manual for details.
. [Help on Speaking]:
Displays useful tips regarding speaking for correct command recognition by the system.
INFO:
The Command List feature is only available when Alternate Command Mode is active.
Getting Started
Before using the voice recognition system for the first time, it is possible to confirm how to use commands by viewing the
Getting Started section of the User Guide.
IVR0073
1. Highlight [Getting Started] and push
<ENTER>.
2. To confirm the page, scroll the screen usingINFINITI controller.
Practicing voice commands
Practice for using the voice recognition function can be performed by repeating a phone number after the system announces it.
IVR0102
1. Highlight [Let’s Practice] and push
<ENTER>.
2. Practice voice commands in accordance with the audio guidance.
Tutorials on operation of voice recognition system
When highlighting [Using the Address
Book], [Finding a Street Address] or [Placing Calls] and pushing <ENTER>, the system displays tutorials on how to perform these operations using voice recogni-
9-3
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (196,1)
9. Voice recognition tion.
IVR0075
Useful tips for correct operation
It is possible to display useful speaking information that may help the system to accept a voice command correctly.
IVR0076
1. Highlight [Help on Speaking] and push
<ENTER>.
2. To confirm the page, scroll the screen using the INFINITI controller.
USING VOICE RECOGNITION SYS-
TEM
Initialization
When the ignition switch is pushed to the
ON position, Voice Recognition is initialized, which may take up to one minute.
When completed, the system is ready to accept voice commands. If <TALK > is pushed before the initialization completes, the display will show the message: “System not ready”.
BEFORE STARTING
To get the best recognition performance from Voice Recognition, observe the following items.
. The interior of the vehicle should be as quiet as possible. Close the windows to eliminate the surrounding noises (traffic noise and vibration sounds, etc.), which may prevent the system from correctly recognizing the voice commands.
. Wait until the tone sounds before speaking a command.
. Speak in a natural conversational voice without pausing between words.
. If the air conditioner is set to “Auto”, the fan speed is automatically lowered so that voice commands can be recognized more easily.
GIVING VOICE COMMANDS
1. Push <TALK wheel.
> located on the steering
IVR0077
2. A list of commands appears on the screen, and the system provides the voice menu prompt “Would you like to access Phone, Navigation, Information,
Audio or Help?”.
3. After the tone sounds and the icon on the screen changes from [ ] to [ ], speak a command.
4. Continue to follow the voice menu prompts and speak after the tone sounds until the preferred operation is completed.
9-4
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (197,1)
9. Voice recognition
Operating tips
. Speak a command after the tone.
. Commands that are available are always shown on the display and spoken through voice menu prompts. Commands other than those that are displayed are not accepted. Follow the prompts given by the system.
. If the command is not accepted, the system announces, “Please say again”.
Repeat the command in a clear voice.
. Push <BACK> once to return to the previous screen.
. To cancel the command, push and hold
<TALK >. The message, “Voice canceled” will be announced.
. Push <TALK > to stop the voice prompt and give the command at once.
Remember to wait for the tone before speaking.
. To adjust the volume of the system feedback, push the volume control buttons <+> or <−> on the steering wheel or use the audio system volume control knob while the system is making an announcement.
How to speak numbers
INFINITI Voice Recognition requires a certain way to speak numbers when giving voice commands. Refer to the following examples.
General rule:
Only single digits 0 (zero) to 9 can be used.
(For example, if speaking 500, “five zero zero” can be used, but “five hundred” cannot.)
Examples:
1-800-662-6200
“One eight zero zero six six two six two zero zero”
Improving Recognition of Phone numbers:
Recognition of phone numbers can be improved by speaking the phone number in 3 groups of numbers. For example, to call 800-662-6200, speak “Eight Zero
Zero” first, and the system will then ask to speak the next three digits. Then, speak
“Six Six Two”. After recognition, the system will then ask to speak the last 4 digits. Speak, “Six Two Zero Zero”. Using this method of phone digit entry can improve recognition performance.
INFO:
For best recognition, speak “zero” for the number “0” and “oh” for the letter “o”.
VOICE COMMAND EXAMPLES
To use the voice recognition function, speaking one command is sometimes sufficient, but at other times it is necessary to speak two or more commands. As examples, some additional basic operations that can be performed by voice commands are described here.
Example 1: Placing call to phone number 800-662-6200
1. Push <TALK wheel.
> located on the steering
IVR0087
2. The system announces, “Would you like to access Phone, Navigation, Information, Audio or Help?”.
9-5
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (198,1)
9. Voice recognition
3. Speak “Phone”.
6. The system announces, “Please say next three digits or dial, or say change number”. Speak “662”.
4. Speak “Dial Number”.
5. Speak “800”.
9-6
Condition: Language=NAM_English/
JVH0493X
IVR0089
IVR0090
IVR0091
7. The system announces, “Please say last four digits or say change number”.
Speak “6200”.
IVR0092
8. The system announces, “Dial or Change
Number?”. Speak “Dial”.
IVR0093
9. The system makes a call to 800-662-
6200.
INFO:
. Speaking “800-662-6200” (10 continuous digits) or “662-6200” (7 continuous digits) is acceptable, if the area code is not necessary. However the 3-3-4 digit grouping is recommended for improved recognition.
“How to speak numbers” (page 9-14)
. The INFINITI voice recognition system is not limited to recognizing phone numbers of only 7 or 10 digits. To dial a number in a format other than the 3-3-4 digit grouping, use the “International Call” command.
. If “Change Number” is spoken during phone number entry, the system will automatically request that the number be repeated using the 3-3-4 format. In this case please speak the area code first and then follow the
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (199,1)
6. Speak “Dial”.
9. Voice recognition prompts.
. Do not add a “1” in front of the area code when speaking phone numbers.
. If the system does not recognize a voice command, please try repeating the command using a natural voice. Speaking too slowly or too loudly may further decrease recognition performance.
Example 2: Placing international call to phone number 011-81-111-
222-333
1. Push <TALK wheel.
> located on the steering
4. Speak “International Call”.
5. Speak “01181111222333”.
JVH0493X
IVR0094
IVR0096
7. The system makes a call to 011-81-
111-222-333.
INFO:
Any digit input format is available in the
International Number input process.
Example 3: Setting destination by street address
1. Push <TALK wheel.
> located on the steering
IVR0087
2. The system announces, “Would you like to access Phone, Navigation, Information, Audio or Help?”.
3. Speak “Phone”.
IVR0095
9-7
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (200,1)
9. Voice recognition
7. Voice feedback will be provided when the command is accepted, and the list of city names is displayed.
8. After the tone sounds and the icon on the screen changes again, speak
“Four”.
IVR0078
2. The system announces, “Would you like to access Phone, Navigation, Information, Audio or Help?”.
3. Speak “Navigation”.
IVR0080
5. Speak the name of the state, “California”.
JNB0276X
4. Speak “Address”.
INFO:
Push <ENTER> or touch [Help] to display the user guide screen.
IVR0081
6. Speak the name of the city, “Gardena”.
IVR0083
9. Speak the name of the street, “South
Figueroa street”.
.
INFO:
Only the official street names stored in the map database can be recognized by the system. To improve accuracy, speak the street name precisely and include
Boulevard, Way, North, South, etc., if known. If unsure of the full name, speaking only part of the street name such as “Figueroa” is acceptable, but recognition accuracy may be reduced.
IVR0082
9-8
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (201,1)
9. Voice recognition
.
To correct the entered city, street or house number, speak “Change City”,
“Change Street” or “Change House
Number”.
12. Speak the house number.
“How to speak numbers”
(page 9-14)
INFO:
If the house number is unknown, speak “No house number”.
IVR0084
10. Voice feedback will be provided when the command is accepted, and the list of street names appears.
11. After the tone sounds and the icon on the screen changes again, speak
“One”.
IVR0085
IVR0086
13. To confirm the destination location on the map, speak “Show Map”. To calculate a route, speak “Calculate
Route”.
ALTERNATE COMMAND MODE
The following section is applicable when
Alternate Command Mode is active.
“Setting alternate command mode”
(page 9-15)
When Alternate Command Mode is active, an expanded list of commands can be used after pushing <TALK >. In this mode, available commands are not fully shown on the display or prompted. Review the expanded command list, available when this mode is active. See examples of
Alternate Command Mode screens. Otherwise, it is recommended that Alternate
Command Mode be turned OFF and Standard Mode be used for the best recognition performance.
“Confirming voice commands”
(page 9-10)
DISPLAYING HOW TO OPERATE
VOICE RECOGNITION SYSTEM
When operating the voice recognition system for the first time or if help is preferred to use the system, the Command
List (available only in Alternate Command
Mode) or the User Guide are available.
9-9
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (202,1)
9. Voice recognition
Basic operation
IVR0097
1. Push <INFO>.
2. Highlight [Others] and push <ENTER>.
3. Highlight [Voice Recognition] and push
<ENTER>.
4. Highlight the preferred item and push
<ENTER>.
Available items
. [Command List]:
A list of voice commands that the system can accept is displayed.
. [User Guide]:
A simplified operation manual of the voice recognition system can be displayed and how to use the voice commands can be confirmed.
INFO:
The Command List feature is only available when Alternate Command Mode is active.
Confirming voice commands
When controlling the system by voice commands for the first time or if an appropriate voice command is unknown, confirm using the voice command lists.
The following information describes how to display the navigation command list and the help list. For information about the operations of other functions, refer to the vehicle Owner’s Manual.
Example: Displaying the navigation command list
1. Push <INFO>.
2. Highlight [Others] and push <ENTER>.
3. Highlight [Voice Recognition] and push
<ENTER>.
IVR0097
4. Highlight [Command List] and push
<ENTER>.
IVR0098
5. Highlight the preferred item and push
<ENTER>.
“Command Lists (Alternate command mode)” (page 9-24)
.
Available items
Phone Commands
.
Navigation Commands
9-10
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (203,1)
9. Voice recognition
.
.
.
Information Commands
Audio Commands
Help Commands
JNI0149X
6. To confirm the list, scroll the screen using the INFINITI controller.
7. Push <BACK> to return to the previous screen.
CONFIRMING HOW TO USE VOICE
COMMANDS
It is possible to confirm how to use voice commands by accessing a simplified User
Guide, which contains basic instructions and tutorials for several voice commands.
IVR0100
Basic operation
1. Push <INFO>.
2. Highlight [Others] and push <ENTER>.
3. Highlight [Voice Recognition] and push
<ENTER>.
4. Highlight [User Guide] and push
<ENTER>.
5. Highlight the preferred item and push
<ENTER>.
Available items
. [Getting Started]:
Describes the basics of how to operate the voice recognition system.
. [Let’s Practice]:
Mode for practice following the system voice.
. [Using the Address Book]:
Tutorial for setting a destination by the
Address Book.
. [Finding a Street Address]:
Tutorial for entering a destination by street address.
. [Placing Calls]:
Tutorial for marking a phone call by voice command operation.
. [Help on Speaking]:
Displays the useful tips of speaking for correct command recognition by the system.
. [Voice Recognition Settings]:
Describes the available voice recognition settings.
. [Adapting the System to Your Voice]:
Tutorial adapting the system to the user’s voice.
Getting Started
Before using the voice recognition system for the first time, it is possible to confirm how to use commands by viewing the
Getting Started section of the User Guide.
9-11
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (204,1)
9. Voice recognition
IVR0101
1. Highlight [Getting Started] and push
<ENTER>.
2. To confirm the page, scroll the screen using the INFINITI controller.
Practicing voice commands
Practice for using the voice recognition function can be performed by repeating a phrase after the system announces it.
2. Practice voice commands in accordance with the audio guidance.
Tutorials on operation of voice recognition system
When highlighting [Using the Address
Book], [Finding a Street Address] or [Placing Calls] and pushing <ENTER>, the system displays tutorials on how to perform these operations using voice recognition.
Example: With [Using the Address Book] highlighted and <ENTER> pushed.
IVR0104
2. The voice guide demonstrates how to speak when giving commands.
3. When the tutorial is completed, the system automatically switches to the
Menu screen.
Useful tips for correct operation
It is possible to display useful speaking tips that may help the system to accept a voice command correctly.
IVR0103
1. Highlight [Using the Address Book] and push <ENTER>. The tutorial starts.
IVR0102
1. Highlight [Let’s Practice] and push
<ENTER>.
9-12
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
IVR0105
Black plate (205,1)
9. Voice recognition
1. Highlight [Help on Speaking] and push
<ENTER>.
2. To confirm the page, scroll the screen using the INFINITI controller.
Voice recognition settings
The settings for easy operation of the voice recognition system are displayed.
IVR0106
1. Highlight [Voice Recognition Settings] and push <ENTER>.
2. To confirm the page, scroll the screen using the INFINITI controller.
Adapting Voice Recognition System to Your Voice
The voice recognition system is equipped with a learning function to adapt to the user’s voice for better recognition. It is possible to confirm how to operate the learning function through this tutorial.
IVR0107
1. Highlight [Adapting the System to Your
Voice] and push <ENTER>. The tutorial starts.
IVR0108
2. The voice guide demonstrates the steps that have to be performed.
3. When the tutorial is completed, the system automatically switches to the
Menu screen.
USING VOICE RECOGNITION SYS-
TEM
Initialization
When the ignition switch is pushed to the
ON position, Voice Recognition is initialized, which may take up to one minute.
When completed, the system is ready to accept voice commands. If <TALK > is pushed before the initialization completes, the display will show the message: “System not ready”.
BEFORE STARTING
To get the best recognition performance out of Voice Recognition, observe the following:
. The interior of the vehicle should be as quiet as possible. Close the windows to eliminate the surrounding noises (traffic noise and vibration sounds, etc.), which may prevent the system from correctly recognizing the voice commands.
. Wait until the tone sounds before speaking a command.
. Speak in a natural conversational voice without pausing between words.
9-13
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (206,1)
9. Voice recognition
. If the air conditioner is set to “Auto”, the fan speed is automatically lowered so that voice commands can be recognized more easily.
. The voice recognition system cannot be operated when the retractable hard top is not closed (for G37 Convertible only).
GIVING VOICE COMMANDS
1. Push <TALK wheel.
> located on the steering
IVR0109
2. A list of commands appears on the screen, and the system announces,
“Please say a command”.
3. After the tone sounds and the icon on the screen changes from [ ] to [ ], speak a command.
Operating tips
. If the command is not recognized, the system announces, “Please say again”.
Repeat the command in a clear voice.
. Push <BACK> once to return to the previous screen.
. To cancel the command, push and hold
<TALK >. The message, “Voice canceled” will be announced.
. Push <TALK > to stop the voice prompt and give the command at once.
Remember to wait for the tone before speaking.
. To adjust the volume of the system feedback, push the volume control buttons [+] or [−] on the steering wheel or use the audio system volume control knob while the system is making an announcement.
How to speak numbers
INFINITI Voice Recognition requires a certain way to speak numbers when giving voice commands. Refer to the following examples.
General rule:
Only single digits 0 (zero) to 9 can be used.
For example, to speak 500, “five zero zero” can be used, but “five hundred” cannot.
Examples:
1-800-662-6200
“One eight zero zero six six two six two zero zero”
Improving Recognition of Phone numbers:
Recognition of phone numbers can be improved by speaking the phone number in 3 groups of numbers. For example, to call 800-662-6200, speak “Eight Zero
Zero” first, and the system will then ask to speak the next three digits. Then, speak
“Six Six Two”. After recognition, the system will then ask to speak the last 4 digits. Speak, “Six Two Zero Zero”. Using this method of phone digit entry can improve recognition performance.
INFO:
For best recognition, speak “zero” for the number “0” and “oh” for the letter “o”.
9-14
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (207,1)
9. Voice recognition
SYSTEM FEEDBACK ANNOUNCE-
MENT MODES
It is possible to select two modes, long or short, for the announcement by the system.
How to set
1. Push <SETTING>.
2. Highlight [Others] and push <ENTER>.
3. Highlight [Voice Recognition] and push
<ENTER>.
IVR0111
4. Highlight [Minimize Voice Feedback] and push <ENTER>. The indicator illuminates, and the system announcement mode switches to the short mode.
5. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
SETTING ALTERNATE COMMAND
MODE
This mode enables the operation of the display and audio through Voice Recognition. When this mode is active, an expanded list of commands can be spoken after pushing <TALK >, and the voice command menu prompts are turned off.
Note that in this mode the recognition success rate may be affected because the number of available commands and ways of speaking each command are increased.
This mode can be turned on or off.
How to set
1. Push <SETTING>.
2. Highlight [Others] and push <ENTER>.
3. Highlight [Voice Recognition] and push
<ENTER>.
4. Highlight [Alternate Command Mode] and push <ENTER>. A confirmation message is displayed. Highlight [Yes] and push <ENTER>. The indicator illuminates, and Alternate Command Mode switches to ON.
5. Push <BACK> to return to the previous screen. Push <MAP> to return to the current location map screen.
SPEAKER ADAPTATION
The voice recognition system has a function to learn the user’s voice for better voice recognition performance.
The system can memorize the voices of up to three persons.
Having system learn user’s voice
1. Push <SETTING>.
2. Highlight [Others] and push <ENTER>.
3. Highlight [Voice Recognition] and push
<ENTER>.
IVR0112
9-15
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (208,1)
9. Voice recognition
IVR0113
4. Highlight [Speaker Adaptation] and push <ENTER>.
IVR0115
6. Highlight [Start Speaker Adaptation
Learning] and push <ENTER>.
JNI0150X
8. Highlight the voice command to be learned by the system, and push
<ENTER>. The voice recognition system starts.
IVR0114
5. Highlight the user whose voice is memorized by the system, and push
<ENTER>.
IVR0116
7. Highlight the voice command category to be learned by the system, and push
<ENTER>. The voice command category list is displayed.
JNI0151X
9. The system announces, “Please say a command”.
10. After the tone sounds and the icon on the screen changes from [ ] to [ ], speak a command.
9-16
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (209,1)
9. Voice recognition
2. Highlight [Others] and push <ENTER>.
3. Highlight [Voice Recognition] and push
<ENTER>.
JNI0152X
11. When the system has recognized the voice command, the voice of the user is learned. Push <BACK> once to return to the previous screen.
INFO:
With [Continuous Learning] set to on, the system does not go back to the command list screen, allowing to continue voice command learning by the system.
12. If the system has learned the command correctly, “None” will change to
“Stored”.
Editing registered items
It is possible to edit user names and select learning function settings.
1. Push <SETTING>.
IVR0120
4. Highlight [Speaker Adaptation] and push <ENTER>.
IVR0122
6. Highlight [Setting] and push <ENTER>.
IVR0121
5. Highlight a user to edit, and push
<ENTER>.
IVR0123
7. Highlight an item to edit, and push
<ENTER>.
Setting items
.
[Edit User Name]:
Edit the user name.
.
[Delete Voice Data]:
Reset the user voice that the voice recognition system has learned.
9-17
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (210,1)
9. Voice recognition
.
[Continuous Learning]:
Have the system learn the voice commands of the user in succession, without selecting commands one by one.
VOICE COMMAND EXAMPLES
To use the voice recognition function, speaking one command is sometimes sufficient, but at other times it is necessary to speak two or more commands. As examples, some additional basic operations by voice commands are described here.
Example 1: Switching map to 2D
(Plan View) mode
3. After the tone sounds and the icon on the screen changes from [ ] to [ ], speak “Plan View Map”.
2. The system announces, “Please say a command”.
3. After the tone sounds and the icon on the screen changes from [ ] to [ ], speak “Places”.
IVR0125
4. Voice feedback will be provided when the command is accepted, and the map is displayed in 2D (Plan View).
Example 2: Setting destination using places list
IVR0127
4. If a route is already set, choose “Near
Current Location”, “Along Route” or
“Near Destination”.
5. After the tone sounds and the icon on the screen changes again, speak
“Along Route”.
1. Push <TALK wheel.
IVR0124
> located on the steering
2. The system announces, “Please say a command”.
9-18
1. Push <TALK wheel.
IVR0126
> located on the steering
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
IVR0128
Black plate (211,1)
9. Voice recognition
6. Voice feedback will be provided when the command is accepted, and the list of places of interest categories appears.
7. After the tone sounds and the icon on the screen changes again, speak
“Two”.
4. Speak the name of the state, “California”.
IVR0129
8. Voice feedback will be provided when the command is accepted, and the list of places of interest in the category specified in the previous step appears.
9. After the tone sounds and the icon on the screen changes again, speak
“One”.
IVR0130
10. Voice feedback will be provided when the command is accepted, and the system starts calculating a route to the selected facility.
Example 3: Setting destination by street address
1. Push <TALK wheel.
> located on the steering
2. The system announces, “Please say a command”.
3. Speak “Address”.
IVR0134
5. Speak the name of the city, “Gardena”.
IVR0133
IVR0135
6. Speak the name of the street, “South
Figueroa street”.
INFO:
Speak the street name precisely including boulevard, way, north, south, etc. In Alternate Command Mode, the system does not recognize abbreviated names when they are
9-19
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (212,1)
9. Voice recognition spoken. In this case, the system does not accept “Figueroa street” or “Figueroa”.
INFO:
If the house number is unknown, speak “No house number”.
IVR0136
7. Voice feedback will be provided when the command is accepted, and the list of street names appears.
8. After the tone sounds and the icon on the screen changes again, speak
“One”.
IVR0138
10. To confirm the destination location on the map, speak “Show Map”. To calculate a route, speak “Calculate
Route”.
9. Speak the house number.
“How to speak numbers”
(page 9-14)
IVR0137
9-20
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
COMMAND LISTS (Standard mode)
Category Command
Phone
Navigation
Information
Audio
Help
Navigation Command
Destination Home
Address
Places
Address Book
Previous Destinations
Black plate (213,1)
9. Voice recognition
Action
Operates the Phone function.
Operates the Navigation function.
Displays the Vehicle Information function.
Operates the Audio function.
Displays the User Guide.
Action
Sets a route to the home location that is stored in the Address book.
Searches for a location by the street address specified, and sets a route (for continental U.S.
and Canada only).
Sets a route to a facility near the current vehicle location.
Searches for information stored in the Address Book.
Sets a route to a previous destination.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
9-21
Black plate (214,1)
9. Voice recognition
Phone
Information
Audio
Command
Dial Number
Quick Dial
Phonebook
Call History Incoming Calls
Outgoing Calls
International Call
Missed Calls
Command
Fuel Economy
Trip Computer (if so equipped)
Maintenance
Where am I?
Traffic Information
Command
AM
FM
XM
CD
Action
Makes a call to a spoken phone number up to 10 digits.
Makes a call to a contact that is stored in the Quick Dial.
Makes a call to a phone number stored in a mobile phone.
Makes a call to an incoming call number.
Makes a call to a dialed number.
Makes a call to a missed calls number.
Makes an international call by allowing more than 10 digits to be spoken.
Action
Displays fuel economy information.
Displays trip information.
Displays maintenance information.
Displays the current location.
Turns the traffic information system on and off.
Action
Turns to the AM band, selecting the station last played.
Turns to the FM band, selecting the station last played.
Turns to the SiriusXM Satellite Radio band, selecting the channel last played.
Starts to play a CD.
9-22
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (215,1)
9. Voice recognition
General
Command
Go back
Exit
Action
Corrects the last recognition result to return to the previous screen.
Cancels Voice Recognition.
INFO:
Refer to the vehicle Owner’s Manual for the operations related to phone, information and audio.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
9-23
Black plate (216,1)
9. Voice recognition
COMMAND LISTS (Alternate command mode)
INFO:
The words in
italics
are variable.
Navigation Commands
Command
Destination Home
Address
Places
Address Book
Previous Destinations
Previous Start Point
Minimize Freeway Route
Fastest Route
Shortest Route
Cancel Route
Delete Destination
Birdview Map
Planview Map
North Up
Heading Up
Zoom In <1 to 13>
9-24
Condition: Language=NAM_English/
Action
Sets a route to your home location.
Sets a route to the street address that you specify (for continental U.S. and Canada only).
Sets a route to a facility near the current vehicle location.
Sets a route to a location stored in the Address Book.
Sets a route to a previously entered destination.
Sets a route to the previous starting point.
Sets the route search condition to minimize the usage of freeways.
Sets the route search condition to find the fastest time.
Sets the route search condition to find the shortest distance.
Stops the current route but can be resumed by using <ROUTE>.
Deletes the entire route (destination and waypoints).
Displays the map in Birdview TM (3D).
Displays the map in Plan View (2D).
Locks the map to make North always point up.
Locks the vehicle indicator to make it always point up.
Increases the magnification of the map by the number of steps specified.
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (217,1)
Navigation Commands
Information Commands
9. Voice recognition
Command
Zoom Out <1 to 13>
Voice Guidance On/Off
Guidance Voice Repeat
Action
Decreases the magnification of the map by the number of steps specified.
Turns the navigation guidance on and off.
Repeats the current navigation voice guidance.
Command Action
Fuel Economy
Tire Pressure (if so equipped)
Displays fuel economy information.
Displays tire pressure information.
Trip Computer (if so equipped) Displays trip information.
Maintenance Displays maintenance information.
Where am I?
Traffic Information
Displays the current location.
Turns the traffic information system on and off.
Weather Information
Weather Map
Displays weather information (for continental U.S. and Canada only).
Displays the weather map (for continental U.S. and Canada only).
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
9-25
Black plate (218,1)
9. Voice recognition
Vehicle Phone Commands
Command
Dial Number
Quick Dial
Phonebook
Call History Incoming Calls
Outgoing Calls
Missed Calls
International Call
Call <name>
Action
Makes a call to a spoken phone number.
Makes a call to a contact that is stored in the Quick Dial.
Makes a call to a contact that is stored in a mobile phone.
Makes a call to an incoming call number.
Makes a call to a dialed number.
Makes a call to a missed calls number.
Makes an international call by allowing more than 10 digits to be spoken.
Makes a call to a contact that is stored in either Quick Dial or Phonebook.
Please say “Call” followed by a stored name.
Audio Commands Command
CD
FM
AM
XM
USB
Bluetooth Audio
AUX (if so equipped)
General Commands Command
Go back
Exit
Action
Starts to play a CD.
Turns to the FM band, selecting the station last played.
Turns to the AM band, selecting the station last played.
Turns to the SiriusXM Satellite Radio band, selecting the channel last played.
Turns on the USB memory.
Turns on the Bluetooth audio player.
Turns on the AUX.
Action
Corrects the last recognition result to return to the previous screen.
Cancels Voice Recognition.
9-26
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (219,1)
9. Voice recognition
Help Commands Command
Command List
Navigation Commands
Phone Commands
Audio Commands
Information Commands
Help Commands
User Guide
Speaker Adaptation
Action
Displays the category list of commands.
Displays the navigation command list.
Displays the phone command list.
Displays the audio command list.
Displays the information command list.
Displays the help command list.
Displays the User Guide
The system memorizes the voices of up to three persons for better voice recognition performance.
INFO:
Refer to the vehicle Owner’s Manual for the operations related to phone, information and audio.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
9-27
Black plate (220,1)
9. Voice recognition
MEMO
9-28
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (221,1)
10 General system information
Directions provided and distances to
Birdview TM ..................................................... 10-3
Detailed Map Coverage Areas (MCA) for
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (222,1)
10. General system information
FEATURES OF THIS NAVIGATION SYSTEM
ROUTE GUIDANCE
The main features of the INFINITI Navigation System are visual guidance and voice guidance in selected map coverage areas.
Utilizing a network of GPS (Global Positioning System) satellites, the INFINITI Navigation System tracks the location on the map and navigates to a preferred location.
Once the destination is set in a map coverage area, the INFINITI Navigation
System will calculate a route from the current location to the destination. The real-time map display and turn-by-turn voice guidance leads the driver along the route. These features can be especially helpful when driving to unfamiliar locations.
The system may be unable to set a destination and/or calculate a route when the destination is outside the map coverage area. Additionally, voice guidance may not be available if the destination is outside the map coverage area. For more information on how to set a destination, refer to section 4.
PLACES OF INTEREST (PLACES) DI-
RECTORY
The INFINITI Navigation System offers an extensive places of interest (Places) directory in map coverage areas. This directory includes a wide variety of destinations ranging from gas stations, ATMs, and restaurants to casinos, ski resorts, shopping centers and businesses. A point of interest can be searched by category, name or phone number. After selecting a destination, the INFINITI Navigation System will calculate a route to that destination.
The Places directory has many uses. For example, the directory can be sorted by the various types of restaurants near the current location. If an ATM or gas station is needed, the INFINITI Navigation System can navigate to the closest preferred location.
For more information on how to use the
Places directory, refer to section 4.
ADDRESS BOOK
The Address Book can store up to 300 locations from map coverage areas into a personal directory. This is especially useful for frequently visited locations, such as clients, relatives and friends. The Address
Book function allows easy access to frequently visited locations when setting them as your destination.
For more information on how to use the
Address Book, refer to section 6.
AVOID AREA
The Avoid Area function sets areas or freeways that the INFINITI Navigation System does not include in the suggested route when calculating routes. For example, if a freeway or area that is always congested with traffic.
For more information on the Avoid Area function, refer to section 6.
NavTraffic INFORMATION
When available, the NavTraffic Information broadcast may help to avoid delays due to traffic incidents. Traffic jams, roadwork, closed roads around the current location, etc. are represented graphically on the map by icons depicting the nature of the event. Incidents on the route are automatically brought to the attention when they are approached.
The NavTraffic Information feature, via the guidance mode, may help to detour around traffic problems. For more information on
10-2
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (223,1)
10. General system information the NavTraffic Information feature, refer to section 5.
AUTOMATIC REROUTE
When detecting a deviation from the suggested route, the INFINITI Navigation
System will automatically recalculate a new route to the destination.
For more information on the Automatic reroute function, refer to section 5.
DETOUR
To make a detour due to traffic conditions, the Detour function calculates an alternative route. The INFINITI Navigation System can calculate a route using secondary roads that will return to primary roads after a specified number of miles.
For more information on the Detour function, refer to section 5.
Birdview
TM
VOICE GUIDANCE
IGE0007
Two map types, the 2D (Plan View) map and Birdview TM (3D) map, are available in the INFINITI Navigation System. Birdview TM map displays the map from an elevated perspective. In Birdview TM map, it is easy to recognize an image of the route because it provides a panoramic view over a long distance.
For more information on Birdview TM refer to section 3.
map,
IGE0008
Route guidance is provided through voice and visual instructions. Voice guidance announces the appropriate directions when approaching an intersection to turn.
For more information on voice guidance, refer to section 5.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
10-3
Black plate (224,1)
10. General system information
CURRENT VEHICLE LOCATION
DISPLAY OF CURRENT VEHICLE LO-
CATION
This navigation system combines the data obtained from the vehicle (by gyro sensor) and from GPS (Global Positioning System) satellites to calculate the current location of the vehicle. This position is then displayed throughout route guidance to a destination.
WHAT IS GPS (Global Positioning
System)?
GPS is a position detecting system that uses satellites deployed by the U.S.
government. This navigation system receives radio signals from three or more different satellites that orbit 13,049 miles
(21,000 km) above the earth in space, and detects the position of the vehicle by utilizing the principle of triangulation.
Positioning adjustment
When the system judges that the vehicle position information is not accurate based on vehicle speed and gyro sensor data calculations, the system will automatically adjust the position of the vehicle icon
10-4 using GPS signals.
Receiving signals from GPS satellites
The reception of GPS signals can be weak, depending on the environment. Vehicles in the following areas/environments may not receive GPS signals (indicator color: gray).
. Inside tunnels or parking garages
INI0121
INI0122
. Areas with numerous tall buildings
. Under multi-layered highways
INI0123
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (225,1)
. Under many large trees
. In a canyon
Condition: Language=NAM_English/
10. General system information
INI0124
INI0253
INFO:
The GPS antenna is located on the instrument panel inside the vehicle. Do not place any objects, especially mobile phones or transceivers, on the instrument panel. Because the strength of the GPS signal is approximately one billionth of that of TV waves, phones and transceivers will affect or may totally disrupt the signal.
Display of GPS information
GPS information can be displayed.
“Viewing GPS current location information” (page 7-32)
NOTE:
Route guidance provided by the navigation system does not take carpool lane driving into consideration, especially when carpool lanes are separated from other road lanes.
INCORRECT DISPLAY OF VEHICLE
POSITION
The following cases may affect the display accuracy of the vehicle’s position or traveling direction. The accuracy will return to normal if the driving conditions return to normal.
INI0125
. When there is a similar road nearby.
INI0126
. When the vehicle is traveling in an area with a grid pattern road system.
10-5
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (226,1)
10. General system information
INI0127
. When the vehicle is passing through a large Y-shaped intersection/junction.
INI0129
. When the vehicle is traveling on a road with repeating S-shaped curves.
INI0131
. When the vehicle is on a snow-covered or unpaved road.
INI0128
. When the vehicle is traveling on a continuous, slowly curving road.
INI0130
. When the vehicle is on a loop bridge.
INI0132
. When repeatedly turning left or right, or driving in zigzags.
10-6
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (227,1)
10. General system information
INI0133
. When the vehicle is rotated on a parking lot turntable while the ignition switch is off.
INI0134
. When driving on a road not displayed on the map screen or a road that has been changed due to additional construction or other reasons.
INI0124
. When the GPS positioning accuracy is low.
INFO:
. The vehicle icon may be misaligned when starting the vehicle just after starting the engine or the hybrid system.
. The vehicle icon may also be misaligned if different sized tires or tire chains are installed.
. The system has a function that automatically corrects the vehicle icon position when it is misaligned from the actual position.
. Vehicle position correction by GPS may not function when the vehicle is stopped.
. If the vehicle icon position does not return to normal even after driving for a while, correct the vehicle icon position manually.
“Adjusting current vehicle location”
(page 8-9)
DETAILED MAP COVERAGE AREAS
(MCA) FOR NAVIGATION SYSTEM
This system is designed to help guiding to the destination, and it also performs other functions as outlined in this manual.
However, the system must be used safely and properly. Information concerning road conditions, traffic signs and the availability of services may not always be up-to-date.
The system is not a substitute for safe, proper and legal driving. Map data covers select metropolitan areas in the United
States and Canada.
Map data includes two types of areas:
“Detailed coverage areas” providing all detailed road data and other areas showing “Main roads only”.
NOTE:
Detailed map data is not available in many areas and is generally limited to select major metropolitan areas.
10-7
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (228,1)
10. General system information
WHEN GRAY ROAD IS DISPLAYED ON
MAP
. When you are driving on a road displayed in gray after the vehicle has deviated from the suggested route during route guidance, automatic rerouting may not start immediately.
. The navigation system does not provide route guidance for roads displayed in dark green. Therefore, if the destination is set on a road displayed in dark green, the enlarged map display will return to the ordinary map screen at some point on a suggested route that is near the destination. Also, voice guidance will stop at some point on a suggested route that is near the destination.
. Places information and street names near roads displayed in gray may not be contained in the map data.
ROUTE CALCULATION
. There may be cases that carpool lanes are included on a suggested route when the automatic rerouting function is activated, even if the “Use Time
Restricted Roads” is turned off.
“Setting conditions for route calculation” (page 5-25)
. The navigation system does not provide route guidance for roads displayed in dark green.
. If the destination is set on a dark green road, the enlarged map display will switch to the ordinary map screen at some point and suggest a route that is near the destination. The distance and direction to the endpoint of the suggested route will be displayed in the lower right corner of the screen. Also, at this time, voice guidance will announce, “The route to the destination includes roads through incomplete map areas. Voice guidance will not be provided in these areas”.
When approaching the endpoint of the suggested route, voice guidance will announce, “Entering the road with incomplete map data. Use the direction
10-8 arrow and distance information to proceed to your destination.”
To reach the destination, refer to the map screen. Always follow actual roads and regulations and drive safely.
. The suggested route may not be the shortest, nor are other circumstances such as traffic jams considered.
. Because of the inevitable difference in road conditions and circumstances between the time you use this system and the time the information was produced for the map data, there may be discrepancies in roads and regulations. In such cases, follow the actual information available.
. During route calculation, the map will not scroll, however the vehicle icon will move with the actual vehicle’s movement.
. During route calculation, buttons such as <ZOOM OUT>/<ZOOM IN> (if so equipped), <MAP>, <DEST> and the
INFINITI controller will be disabled.
. In some cases, after the calculation is complete, the calculated route may not be immediately displayed.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (229,1)
. Waypoints that have been passed will be disregarded by rerouting calculation.
. If you scroll the map while the suggested route is being drawn, it may take more time to finish drawing.
. If waypoints are set, the system calculates multiple routes between waypoints simultaneously, and the following may result.
— If one section between waypoints cannot be calculated, none of the route will be displayed.
— The route may not connect completely at some waypoints.
— The route may require a U-turn close to some waypoints.
. Route calculation may not be completed in the following cases.
— If there is no main road within a range of
1.5 miles (2.5 km) from the vehicle, a message saying so will appear on the screen. Try recalculating when the vehicle is closer to a main road.
— If there is no main road within a range of
1.5 miles (2.5 km) from the destination or waypoint, a message saying so will appear on the screen. Try setting the location closer to a main road.
— If the vehicle is too close to the destination or if there are no roads to the destination, a message saying so will appear on the screen.
— If it is impossible to reach the destination or waypoints because of traffic regulations, etc.
— If the only route to reach the destination or waypoints is extremely complicated.
— If the destination, current vehicle position or waypoint is within the “Avoid
Area”.
— If a part of the route is included in the
“Avoid Area”.
. The following may occur when the route is displayed.
— If you calculate a route on a main road, the starting point of the route may not exactly match the current vehicle location.
— The endpoint of the route may not exactly match the destination.
— If you calculate a route on a main road, the system may display a route from
10. General system information another main road. This may be because the position of the vehicle icon is not accurate. In this case, park the vehicle in a safe location and reset the vehicle icon, or continue driving to see if the position of the vehicle icon is automatically adjusted before recalculating the route.
— There are cases in which the system shows an indirect route to reach the destination or waypoints, if you set them from stored or facility information. In order to correct this, you must be careful about the traffic direction, especially when lanes with different travel directions are shown separately, such as interchanges and service areas.
— This system makes no distinction between limited traffic control and total control (blockage). It may show an indirect route even if the road is usable.
— Even if the freeway preference is set to
OFF, a route that uses the freeway may be suggested.
— Even if the ferry preference is set to OFF, a route that uses a ferry line may be suggested.
10-9
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (230,1)
10. General system information
— Ferry lines, excluding those that are only for pedestrians, bicycles and motorcycles, are stored in this system. Take into consideration the travel time required and operational condition before deciding whether to use them or not.
ROUTE GUIDANCE
INFO:
The system will only announce street names when the system language is set to English.
Street names are not announced when the system is set to Français (French).
BASICS OF VOICE GUIDANCE
Voice guidance announces which direction to turn when approaching an intersection in which a turn is necessary.
NOTE:
. There may be some cases in which voice guidance and actual road conditions do not correspond. This may occur because of discrepancies between the actual road and the information on the map data, or it is due to the vehicle’s speed.
. In case voice guidance does not correspond to the actual road conditions, follow the information obtained from traffic signs or notices on the road.
. Route guidance provided by the navigation system does not take carpool lane driving into consideration, especially when carpool lanes are separated from other road lanes.
DIRECTIONS PROVIDED AND DIS-
TANCES TO GUIDE POINTS
Directions will differ, depending on the road type.
INFO:
Distances may vary, depending on the vehicle speed.
Notification of intersection on ordinary road
INI0135
1. “In about one quarter mile (400 meters), right (left) turn.”
2. “Right (left) turn ahead.”
10-10
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Notification of consecutive intersections on ordinary roads
Notification of freeway entrance
Black plate (231,1)
10. General system information
INI0136
When the road has three or more consecutive intersections ahead, voice guidance will announce the following.
1. “In about one quarter mile (400 meters), right (left) turn, then in about one quarter mile (100 meters) left (right) turn.”
2. “Left (right) turn ahead, then in about one quarter mile (100 meters) right
(left) turn.”
INI0137
1. “In about one quarter mile (400 meters) freeway entrance on your right onto
(road number and direction).”
2. “Freeway entrance on your right onto
(road number and direction).”
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
10-11
10. General system information
Notification of freeway junction
Black plate (232,1)
Notification of freeway exit
1. “In about one mile (1.6 kilometers), keep to the right (left) onto (road number and direction), then in about one quarter mile (400 meters) keep to the right (left).”
2. “Keep to the right (left) onto (road number and direction), then in about one quarter mile (400 meters) keep to the right (left) onto (road number and direction).”
INI0138
3. “Keep to the right (left) onto (road number and direction).”
IGE0006
1. “In about one mile (1.6 kilometers), exit on your right.”
2. “Take the exit on your right.”
Notification when approaching destination
Ordinary road:
When approaching the destination, voice guidance will announce, “You have arrived at your destination. Ending route guidance.” To finally reach your destination, refer to the map screen.
Dark green road:
After passing the last turning point on a suggested route, voice guidance will announce, “The route to your destination includes roads through incomplete map areas. Voice guidance will not be provided
10-12
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (233,1)
10. General system information in these areas.” When approaching the endpoint of the suggested road, voice guidance will announce, “Entering the road with incomplete map data. Please use the direction arrow and distance information to proceed to your destination.”
REPEATING VOICE GUIDANCE
This function is available throughout route guidance, from the time after the route calculation is completed until the vehicle arrives at the destination. Push <VOICE>.
Voice guidance will be repeated.
INFO:
. If <VOICE> is pushed when the vehicle is deviating from the suggested route and when the automatic reroute function is off, voice guidance will announce, “Proceed to the highlighted route.”
. If <VOICE> is pushed when the vehicle is going in the wrong direction, voice guidance will announce: “Please make a legal U-turn if possible.”
NOTES ON VOICE GUIDANCE
. Voice guidance in this system should be regarded as a supplementary function. When driving the vehicle, check the route on the map and follow the actual roads and traffic regulations.
. Voice guidance is activated only for intersections with certain conditions.
There may be cases that the vehicle has to turn, but voice guidance is not provided.
. Voice guidance contents may vary, depending on the direction of the turn and the type of intersection.
. The voice guidance timing will vary depending on the situation.
. When the vehicle has deviated from the suggested route, voice guidance is not available. The system will not announce this. Refer to the map and recalculate the route.
“Recalculate route” (page 5-22)
. Voice guidance may not accurately correspond with road numbers and directions at freeway junctions.
. Voice guidance may not accurately correspond to street names at freeway exits.
. The displayed street names may sometimes differ from the actual names, or
“UNKNOWN STREET NAME” may be displayed.
. Voice guidance is not available when the [Guidance Voice] is turned off.
“Turning voice guidance ON/OFF”
(page 2-25)
. Voice guidance will start when the vehicle enters the suggested route.
Refer to the map for directions to the starting point of the route.
. When approaching a waypoint, voice guidance will announce, “You have arrived at waypoint 1 (2, 3, 4,...).”
Voice guidance will switch to the next section of the route. When voice guidance is not available, refer to the map for directions.
. In some cases, voice guidance ends before arrival at the destination. Refer to the destination icon on the map to reach the destination.
. If the system recognizes on which side the destination (waypoint) is located, voice guidance will announce “on the
10-13
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
10. General system information right/left” after announcing the arrival at the destination.
. Voice guidance may be partially operational or inoperative due to the angle of roads at an intersection.
. Because freeway lane information is available only for approximately 7,000 major freeways in North America, it is not possible to display information for all junctions and exits.
. Freeway exit information may differ from the information on the actual exit signs.
. Because it is not possible to consider data concerning roads that are seasonally available or unavailable, a route may be displayed that does not match the actual traffic restrictions. Be sure to follow the actual traffic restrictions while driving.
. Canada and Alaska contain many roads with incomplete map data. As a result, when searching for a route, the route may include roads with incomplete data. In regions where road data is not complete, voice guidance may stop for long periods of time. Be sure to follow the actual traffic restrictions
10-14
Condition: Language=NAM_English/ while driving.
Black plate (234,1)
NOTES ON NavTraffic INFORMATION
. The NavTraffic information service is not provided for some cities. In addition, the cities for which the traffic information service is provided may be changed.
. In some cases, infrastructure problems may prevent the complete display of the traffic information. This is not a malfunction.
. Due to infrastructure problems, or due to the time when the traffic information service broadcast is received, the displayed information may differ from the actual traffic conditions.
. Depending on the traffic information, a detour route may be slower than the original route.
. NavTraffic is a service of SiriusXM
Satellite Radio. NavTraffic is only available in select markets and is subject to data availability. Reception of the
SiriusXM signal may vary depending on location. It requires a monthly premium subscription. The service provider is solely responsible for the quality and accuracy of the information
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (235,1)
10. General system information provided. All fees and programming are subject to change. For more details on the NavTraffic service, terms and conditions, please visit www.siriusxm.com/navtraffic.
You can also contact SiriusXM Satellite
Radio at 1-866-635-2349.
. As of January 31, 2009, the NavTraffic service covers 80 major metropolitan markets. For the most current list of markets covered, please refer to www.
siriusxm.com/navtraffic, or call SiriusXM Satellite Radio customer support at 1-866-635-2349.
. Due to road maintenance, infrastructure problems (e.g. malfunction of road sensors, outage of central computer of infrastructure) or natural disasters, there are times when some or all traffic information may not be available.
. Incident information is based on human collection. Not all incidents that have happened are collected and provided.
. Due to infrastructure problems, or transmission delay, there are times when the information may differ from the actual condition. Always observe safe driving practices and follow all traffic regulations.
. Due to the coverage and quality of traffic information and road conditions, it is not always possible for the system to provide the shortest time route even when traffic information is considered.
. Traffic information that is displayed may differ from information from other media (e.g., radio), as other media may use different information sources.
. If the Infiniti Connection (if so equipped) Text-to-Speech function is used after downloading information feeds immediately after the navigation system is started up, it may take some time until the NavTraffic information is displayed on the screen.
NOTES ON NavWeatherXM INFORMA-
TION
. The NavWeatherXM information service is not provided for some cities. In addition, the cities for which the weather information service is provided may be changed.
. In some cases, infrastructure problems may prevent the complete display of the weather information. This is not a malfunction.
. Due to infrastructure problems, or due to the time when the weather information service broadcast is received, the displayed information may differ from the actual weather conditions.
. NavWeatherXM is a service of SiriusXM
Satellite Radio. NavWeatherXM is only available in select markets and is subject to data availability. Reception of the SiriusXM signal may vary depending on location. It requires a monthly premium subscription. The service provider is solely responsible for the quality and accuracy of the information provided. All fees and programming are subject to change.
10-15
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (236,1)
10. General system information
For more details on the NavWeatherXM service, terms and conditions, please visit www.siriusxm.com/navweather.
You can also contact SiriusXM Satellite
Radio at 1-866-635-2349.
. NavWeatherXM is designed to provide real-time weather and forecasting information in your general vicinity. Discrepancies may be encountered between the system and your actual location. Road system and weather changes may affect the accuracy of the information provided. Rely on your common sense to decide whether to follow a specified route. Detailed coverage is not available in every city or roadway.
MAP DATA
HOW TO ORDER MAP DATA UP-
DATES
To order updated map data, contact the
INFINITI NAVIGATION SYSTEM HELPDESK.
See the contact information on the inside front cover of this manual.
ABOUT MAP DATA
1. This map data has been prepared by
Hitachi Automotive Systems, Ltd. under licence from ZENRIN CO., LTD. and
NAVTEQ. ZENRIN CO., LTD. has added, processed and digitized data based on the digital road map data of Navigation
Technologies Corporation. Due to the production timing of the map data, some new roads may not be included in this map data or some of the names or roads may be different from those at the time you use this map data.
2. Traffic control and regulation data used in this map data may be different from those at the time you use this map data due to the data production timing.
When driving your vehicle, follow the actual traffic control signs and notices on the roads.
10-16
3. Reproducing or copying this map software is strictly prohibited by law.
Published by NISSAN North America, Inc.
2006 Navigation Technologies. All rights reserved.
Certain business data provided by infogroup * 2010, All Rights Reserved.
1993-2008 NAVTEQ. All Rights Reserved.
2008, All Rights Reserved.
ZENRIN CO., LTD. 2009. All rights reserved.
ZENRIN USA, INC. 2008. All rights reserved.
2008 Zagat Survey, LLC.
WARNING!
GUID-678F6CA2-2608-4017-95A0-B5D303B42509
.
This navigation system should not be used to replace your own judgement. No itinerary suggested by this navigation system should ever override any highway regulations, your own judgement, or a knowledge of safe driving practices. Do not follow the navigation system’s suggested itinerary if it would cause you to perform a dangerous or illegal act, place you in a dangerous situation, or take you into an area you consider unsafe.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (237,1)
10. General system information
.
The advice provided by the navigation system is to be regarded as a suggestion only. There may be times when the navigation system displays the vehicle’s location incorrectly, fails to suggest the shortest route, or fails to direct you to the your desired destination. In such instances, rely on your own driving judgement, taking into account the driving conditions at the time.
.
Do not use the navigation system to locate emergency services. The database does not contain a complete listing of emergency services such as police stations, fire halls, hospitals and walk-in clinics. Please show discretion and ask for directions in such instances.
.
As the driver, you alone are responsible for your driving safety.
— In order to avoid a traffic accident, do not operate the system while driving.
— In order to avoid a traffic accident, operate the system only when the vehicle is stopped at a safe place and the parking brake is on.
— In order to avoid a traffic accident or traffic offence, remember that actual road conditions and traffic regulations take precedence over the information contained on the navigation system.
— The Software may contain inaccurate or incomplete information due to the passage of time, changing circumstances, and the sources of information used. Please respect current traffic conditions and regulations at all times while driving.
— Where actual road conditions and highway regulations differ from the information contained on the navigation system, abide by the highway regulations.
— Keep the amount of time spent viewing the screen while driving to a strict minimum.
The navigation system does not provide, nor represent in any way information on: traffic and highway regulations; technical aspects of the vehicle including weight, height, width, load and speed limits; road conditions including grade, percentage of incline and surface conditions; obstacles such as the height and width of bridges and tunnels; and other current driving or road conditions. Always rely on your own judgement when driving a car, taking into account current driving conditions.
The marks of companies displayed by this product to indicate business locations are the marks of their respective owners. The use of such marks in this product does not imply any sponsorship, approval, or endorsement by such companies of this product.
END-USER TERMS
The data (“Data”) is provided for your personal, internal use only and not for resale. It is protected by copyright, and is subject to the following terms and conditions which are agreed to by you, on the one hand, and Hitachi Automotive Systems, Ltd. and its licensors (including their licensors and suppliers) on the other hand.
2008 NAVTEQ. All rights reserved.
The Data for areas of Canada includes information taken with permission from
Her
Queen’s Printer for Ontario, *
Corporation, GeoBase
®
.
Canada Post
NAVTEQ holds a non-exclusive license from the United States Postal Service publish and sell ZIP+4
® information.
® to
10-17
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (238,1)
10. General system information
United States Postal Service
®
2008.
Prices are not established, controlled or approved by the United States Postal
Service
®
. The following trademarks and registrations are owned by the USPS:
United States Postal Service, USPS, and
ZIP+4.
The Data may include or reflect data of licensors, including Her Majesty the Queen in the Right of Canada (“Her Majesty”),
Canada Post Corporation (“Canada Post”) and the Department of Natural Resources
Canada (“NRCan”). Such data is licensed on an “as is” basis. The licensors, including Her Majesty, Canada Post and NRCan, make no guarantees, representations or warranties respecting such data, either express or implied, arising by law or otherwise, including but not limited to, effectiveness, completeness, accuracy or fitness for a particular purpose.
The licensors, including Her Majesty, Canada Post and NRCan, shall not be liable in respect of any claim, demand or action, irrespective of the nature of the cause of the claim, demand or action alleging any loss, injury or damages, direct or indirect, which may result from the use or possession of the data or the Data. The licensors,
10-18 including Her Majesty, Canada Post and
NRCan, shall not be liable in any way for loss of revenues or contracts, or any other consequential loss of any kind resulting from any defect in the data or the Data.
End User shall indemnify and save harmless the licensors, including Her Majesty,
Canada Post and NRCan, and their officers, employees and agents from and against any claim, demand or action, irrespective of the nature of the cause of the claim, demand or action, alleging loss, costs, expenses, damages or injuries (including injuries resulting in death) arising out of the use or possession of the data or the
Data.
Terms and conditions
Personal Use Only. You agree to use this
Data together with Nissan Automotive
Products for the solely personal, noncommercial purposes for which you were licensed, and not for service bureau, timesharing or other similar purposes. Accordingly, but subject to the restrictions set forth in the following paragraphs, you may copy this Data only as necessary for your personal use to (i) view it, and (ii) save it, provided that you do not remove any copyright notices that appear and do not modify the Data in any way. You agree not to otherwise reproduce, copy, modify, decompile, disassemble or reverse engineer any portion of this Data, and may not transfer or distribute it in any form, for any purpose, except to the extent permitted by mandatory laws. Multi-disc sets may only be transferred or sold as a complete set as provided by Hitachi Automotive Systems,
Ltd. and not as a subset thereof.
Restrictions. Except where you have been specifically licensed to do so by Hitachi
Automotive Systems, Ltd., and without limiting the preceding paragraph, you may not (a) use this Data with any products, systems, or applications in-
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (239,1)
10. General system information stalled or otherwise connected to or in communication with vehicles, capable of vehicle navigation, positioning, dispatch, real time route guidance, fleet management or similar applications; or (b) with or in communication with any positioning devices or any mobile or wireless-connected electronic or computer devices, including without limitation cellular phones, palmtop and handheld computers, pagers, and personal digital assistants or
PDAs.
Warning. The Data may contain inaccurate or incomplete information due to the passage of time, changing circumstances, sources used and the nature of collecting comprehensive geographic data, any of which may lead to incorrect results.
No Warranty. This Data is provided to you
“as is,” and you agree to use it at your own risk. Hitachi Automotive Systems, Ltd. and its licensors (and their licensors and suppliers) make no guarantees, representations or warranties of any kind, express or implied, arising by law or otherwise, including but not limited to, content, quality, accuracy, completeness, effectiveness, reliability, fitness for a particular purpose, usefulness, use or results to be obtained from this Data, or that the Data or server will be uninterrupted or error-free.
Disclaimer of Warranty: HITACHI AUTOMO-
TIVE SYSTEMS, LTD. AND ITS LICENSORS
(INCLUDING THEIR LICENSORS AND SUPPLI-
ERS) DISCLAIM ANY WARRANTIES, EXPRESS
OR IMPLIED, OF QUALITY, PERFORMANCE,
MERCHANTABILITY, FITNESS FOR A PARTI-
CULAR PURPOSE OR NONINFRINGEMENT.
Some States, Territories and Countries do not allow certain warranty exclusions, so to that extent the above exclusion may not apply to you.
Disclaimer of Liability: HITACHI AUTOMO-
TIVE SYSTEMS, LTD. AND ITS LICENSORS
(INCLUDING THEIR LICENSORS AND SUPPLI-
ERS) SHALL NOT BE LIABLE TO YOU: IN
RESPECT OF ANY CLAIM, DEMAND OR
ACTION, IRRESPECTIVE OF THE NATURE OF
THE CAUSE OF THE CLAIM, DEMAND OR
ACTION ALLEGING ANY LOSS, INJURY OR
DAMAGES, DIRECT OR INDIRECT, WHICH
MAY RESULT FROM THE USE OR POSSES-
SION OF THE INFORMATION; OR FOR ANY
LOSS OF PROFIT, REVENUE, CONTRACTS OR
SAVINGS, OR ANY OTHER DIRECT, INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF YOUR USE OF
OR INABILITY TO USE THIS INFORMATION,
ANY DEFECT IN THE INFORMATION, OR THE
BREACH OF THESE TERMS OR CONDITIONS,
WHETHER IN AN ACTION IN CONTRACT OR
TORT OR BASED ON A WARRANTY, EVEN IF
HITACHI AUTOMOTIVE SYSTEMS, LTD. OR
ITS LICENSORS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. Some
States, Territories and Countries do not allow certain liability exclusions or damages limitations, so to that extent the above may not apply to you.
Export Control. You agree not to export from anywhere any part of the Data provided to you or any direct product thereof except in compliance with, and with all licenses and approvals required under, applicable export laws, rules and regulations.
Entire Agreement. These terms and conditions constitute the entire agreement between Hitachi Automotive Systems, Ltd.
(and its licensors, including their licensors and suppliers) and you pertaining to the subject matter hereof, and supersedes in their entirety any and all written or oral agreements previously existing between us with respect to such subject matter.
Governing Law. The above terms and conditions shall be governed by the laws
10-19
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (240,1)
10. General system information of the State of Illinois, without giving effect to (i) its conflict of laws provisions, or (ii) the United Nations Convention for Contracts for the International Sale of Goods, which is explicitly excluded. You agree to submit to the jurisdiction of the State of
Illinois for any and all disputes, claims and actions arising from or in connection with the Data provided to you hereunder.
Government End Users. If the Data is being acquired by or on behalf of the United
States government or any other entity seeking or applying rights similar to those customarily claimed by the United States government, NAVTEQ Data (hereinafter
“Data”) is a “commercial item” as that term is defined at 48 C.F.R. (“FAR”) 2.101, is licensed in accordance with ENDUSER
TERMS, and each copy of the Data delivered or otherwise furnished shall be marked and embedded as appropriate with the following “Notice of Use,” and shall be treated in accordance with such Notice:
NOTICE OF USE
CONTRACTOR (MANUFACTURER/SUPPLIER) NAME:
NAVTEQ
CONTRACTOR (MANUFACTURER/SUPPLIER) AD-
DRESS: 425 West Randolph St., Chicago, Illinois
60606
This Data is a commercial item as defined in FAR
2.101 and is subject to END-USER TERMS under which this Data was provided.
2008 NAVTEQ - All rights reserved.
If the Contracting Officer, federal government agency, or any federal official refuses to use the legend provided herein, the
Contracting Officer, federal government agency, or any federal official must notify
NAVTEQ prior to seeking additional or alternative rights in the Data.
HOW TO HANDLE DISPLAY
The display is a liquid crystal display and should be handled with care.
WARNING!
GUID-B6DE101D-0F43-4E75-8F7C-975DDA746AEC
Never disassemble the display. Some parts utilize extremely high voltage. Touching them may result in serious personal injury.
CHARACTERISTICS OF LIQUID CRYS-
TAL DISPLAY
. If the temperature inside the vehicle is especially low, the display will stay relatively dim or the movement of the images may be slow. These conditions are normal. The display will function normally when the interior of the vehicle has warmed up.
. Some pixels in the display are darker or brighter than others. This condition is an inherent characteristic of liquid crystal displays, and it is not a malfunction.
. A remnant of the previous display image may remain on the screen. This screen burn is inherent in displays, and
10-20
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (241,1)
10. General system information it is not a malfunction.
INFO:
The screen may become distorted by strong magnetic fields.
MAINTENANCE OF DISPLAY
WARNING!
GUID-9F5FAC95-B51E-4AF3-BCB1-B04C5EF0D507
.
To clean the display, never use a rough cloth, alcohol, benzine, thinner and any kind of solvent or paper towel with a chemical cleaning agent. They will scratch or deteriorate the panel.
.
Do not splash any liquid such as water or car fragrance on the display. Contact with liquid will cause the system to malfunction.
To clean the display screen, use a dry, soft cloth. If additional cleaning is necessary, use a small amount of neutral detergent with a soft cloth. Never spray the screen with water or detergent. Dampen the cloth first, then wipe the screen.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
10-21
Black plate (242,1)
10. General system information
MEMO
10-22
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
11 Troubleshooting guide
Black plate (243,1)
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (244,1)
11. Troubleshooting guide
CUSTOMER ASSISTANCE
For assistance or inquiries about the
INFINITI Navigation System, contact the
INFINITI NAVIGATION SYSTEM HELPDESK.
See the contact information on the inside front cover of this manual.
11-2
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (245,1)
11. Troubleshooting guide
BASIC OPERATIONS
Symptom
No image is displayed.
No voice guidance is available.
or
The volume is too high or too low.
No map is displayed on the screen.
The screen is too dim. The movement is slow.
Some pixels in the display are darker or brighter than others.
Some menu items cannot be selected.
Possible cause
The brightness is at the lowest setting.
The system in the video mode.
Possible solution
Adjust the brightness of the display.
Push the appropriate button (depending on models) on the control panel to change the mode. Refer to the vehicle Owner’s Manual.
The display is turned off.
Push <DAY/NIGHT OFF> to turn on the display.
The volume is not set correctly, or it is turned off.
Adjust the volume of voice guidance.
Voice guidance is not provided for certain streets
(roads displayed in gray).
A screen other than map screen is displayed.
This is not a malfunction.
Push <MAP>.
The temperature in the interior of the vehicle is low. Wait until the interior of the vehicle has warmed up.
This condition is an inherent characteristic of liquid crystal displays.
Some menu items become unavailable while the vehicle is driven.
This is not a malfunction.
Park the vehicle in a safe location, and then operate the navigation system.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
11-3
Black plate (246,1)
11. Troubleshooting guide
VEHICLE ICON
Symptom
Names of roads and locations differ between
Plan View and Birdview TM .
The vehicle icon is not displayed in the correct position.
Possible cause
This is because the quantity of the displayed information is reduced so that the screen does not become too crowded. There is also a chance that names of the roads or locations may be displayed multiple times, and the names appearing on the screen may be different because of a processing procedure.
The vehicle was transported after the ignition switch was pushed off, for example, by a ferry or car transporter.
The position and direction of the vehicle icon may be incorrect depending on the driving environments and the levels of positioning accuracy of the navigation system.
Possible solution
This is not a malfunction.
Drive the vehicle for a while on a road where GPS signals can be received.
This is not a malfunction. Drive the vehicle for a while to automatically correct the position and direction of the vehicle icon.
“Current vehicle location” (page 10-4)
Updated road information will be included in the next version of the map data.
When the vehicle is traveling on a new road, the vehicle icon is located on another road nearby.
The screen does not switch to the night screen even after turning on the headlights.
Because the new road is not stored in the map data, the system automatically places the vehicle icon on the nearest road available.
The daytime screen was set the last time the headlights were turned on.
The current location map screen is not displayed.
Set the screen to the night screen mode using <DAY/NIGHT OFF> when turning on the headlights.
“Display settings” (page 8-3)
Push <MAP>.
The map does not scroll even when the vehicle is moving.
The vehicle icon is not displayed.
The current location map screen is not displayed.
Push <MAP>.
11-4
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (247,1)
11. Troubleshooting guide
Symptom Possible cause
The GPS indicator on the screen remains gray. GPS signals cannot be received under certain conditions, such as in a parking garage, on a road with many tall buildings, etc.
GPS signals cannot be received because objects are placed on the instrument panel.
A sufficient number of GPS satellites is not available.
The location of the vehicle icon is misaligned from the actual position.
When using tire chains or replacing the tires, speed calculations based on the speed sensor may be incorrect.
The map data has a mistake or is incomplete (the vehicle icon position is always misaligned in the same area).
Possible solution
Drive on an open, straight road for a while.
Remove the objects from the instrument panel.
Wait for the satellites to move to locations available for the navigation system.
Drive the vehicle for about 30 minutes at approximately 19 MPH (30 km/h) to automatically correct the vehicle icon position.
If this does not correct the vehicle icon position, contact an INFINITI retailer.
Updated road information will be included in the next version of the map data.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
11-5
Black plate (248,1)
11. Troubleshooting guide
ROUTE CALCULATION AND VISUAL GUIDANCE
Symptom
Waypoints are not included in the auto reroute calculation.
Route information is not displayed.
Possible cause
Waypoints that have been already passed are not included in the auto reroute calculation.
Route calculation has not yet been performed.
The auto reroute calculation (or detour calculation) suggests the same route as the one previously suggested.
A waypoint cannot be added.
Five waypoints are already set on the route, including ones that the vehicle has already passed.
Possible solution
To go to that waypoint again, edit the route.
The vehicle is not on the suggested route.
Route guidance is set to off.
Route information is not provided for certain types of roads (roads displayed in gray).
Route calculations took priority conditions into consideration, but the same route was calculated.
Set the destination and perform route calculation.
Drive on the suggested route.
Turn on route guidance.
This is not a malfunction.
This is not a malfunction.
[Calculate] must be selected for route calculation after Waypoints are selected from the “Edit/Add to Route” screen.
A maximum of 5 waypoints can be set on the route. To go to 6 or more waypoints, perform route calculations multiple times as necessary.
Highlight [Calculate] and push <ENTER> after selecting waypoints.
11-6
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (249,1)
11. Troubleshooting guide
Symptom
The suggested route is not displayed.
Possible cause
Roads near the destination cannot be calculated.
The starting point and destination are too close.
The starting point and destination are too far away.
There are time restricted roads (by the day of the week, by time) near the current vehicle location or destination.
A part of the route is not displayed.
The part of the route that the vehicle has already passed is deleted.
An indirect route is suggested.
The suggested route includes narrow streets (roads displayed in gray).
A route is managed by sections between waypoints. If the vehicle passed the first waypoint, the section between the starting point and the waypoint is deleted (it may not be deleted depending on the area).
If there are restrictions (such as one-way streets) on roads close to the starting point or destination, the system may suggest an indirect route.
The system may suggest an indirect route because route calculation does not take into consideration some areas such as narrow streets (gray roads).
This may be caused by insufficient or incorrect map data.
The landmark information does not correspond to the actual information.
The suggested route does not exactly connect to the starting point, waypoints, or destination.
There is no data for route calculation closer to these locations.
Possible solution
Reset the destination to a main or ordinary road, and recalculate the route.
Set a more distant destination.
Divide the trip by selecting one or two intermediate destinations, and perform route calculations multiple times.
Set [Use Time Restricted Roads] to off.
“Setting conditions for route calculation” (page 5-25)
This is not a malfunction.
This is not a malfunction.
Adjust the location of the starting point or destination.
Reset the destination to a main or ordinary road, and recalculate the route.
Updated information will be included in the next version of the map data.
Set the starting point, waypoints and destination on a main road, and perform route calculation.
11-7
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (250,1)
11. Troubleshooting guide
VOICE GUIDANCE
Symptom
Voice guidance is not available.
The guidance content does not correspond to the actual condition.
Possible cause
Voice guidance is only available at certain intersections marked with . In some cases, voice guidance is not available even when the vehicle should make a turn.
The vehicle has deviated from the suggested route.
Voice guidance is set to off.
Route guidance is set to off.
The content of voice guidance may vary, depending on the types of intersections at which turns are made.
Possible solution
This is not a malfunction.
Go back to the suggested route or request route calculation again.
Turn on voice guidance.
Turn on route guidance.
Follow all traffic rules and regulations.
11-8
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (251,1)
11. Troubleshooting guide
INFINITI CONNECTION
TM
(if so equipped)
The system cannot connect to the Infiniti Connection Data
Center.
Symptom Possible cause
A subscription for the Infiniti Connection service has not been established.
The communication line is busy.
The vehicle is in a location where it is difficult to receive radio waves.
TCU (Telematics Communication Unit) is not turned on.
Radio wave reception is not sufficient for
TCU operation.
Possible solution
Sign up for a subscription to the Infiniti Connection service. For details about subscriptions, contact the Infiniti Connection support line at 1-800-334-7858 (for
U.S.) /1-855-892-7418 (for Canada).
Try again after a short period of time.
When the vehicle moves to an area where radio waves can be transmitted sufficiently, communication will be restored. When the icon on the display shows that the vehicle is inside the communication area, the system can be used.
If the icon does not show that the vehicle is inside the communication area despite the fact that the vehicle is in that location, contact the Infiniti Connection support line at 1-800-334-7858 (for U.S.) /1-855-892-7418 (for Canada).
When the vehicle moves to an area where radio waves can be transmitted sufficiently, communication will be restored. When the icon on the display shows that the vehicle is inside the communication area, the system can be used.
The vehicle is being driven. Stop the vehicle in a safe location and apply the parking brake before operating the functions.
Some of the items that are displayed on the menu screen cannot be selected.
Some parts of the screen are not displayed.
The system does not announce information.
The vehicle is being driven and some menu items are disabled.
The vehicle is being driven and some menu items are disabled.
Operate the system after stopping the vehicle in a safe location and applying the parking brake.
The volume level is set to the minimum.
Adjust the volume level by operating the VOLUME control knob located on the control panel or on the steering wheel switch while the system is announcing information.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
11-9
Black plate (252,1)
11. Troubleshooting guide
VOICE RECOGNITION
Symptom
The system does not accept the voice command.
or
The system accepts the voice command incorrectly.
The system cannot be operated.
Possible cause
The interior of the vehicle is too noisy.
The volume of the voice is too low.
The volume of the voice is too loud.
Pronunciation is unclear.
The voice command is given before the voice recognition system is ready.
8 seconds or more have passed after pushing <TALK steering wheel.
> on the
Possible solution
Close the windows or have other occupants be quiet.
Speak louder.
Speak softer.
Speak clearly.
Push <TALK > on the steering wheel, and speak a command after the tone sounds.
Make sure to speak a command within 8 seconds after the beep tone sounds.
Only a limited range of voice commands is usable for each screen. Use a correct voice command appropriate for the current screen.
The retractable hard top is not closed (G37 Convertible only).
Close the retractable hard top.
INFO:
For the best recognition, speak the appropriate commands. Command lists are available earlier in this manual.
Standard Mode:
“Command lists (Standard mode)”
(page 9-21)
Alternate Command Mode:
“Command Lists (Alternate command mode)” (page 9-24)
11-10
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Black plate (253,1)
11. Troubleshooting guide
TRAFFIC INFORMATION
Symptom
The traffic information is not displayed.
With the automatic detour route search ON, no detour route is set to avoid congested areas.
The route does not avoid a road section with traffic information stating that it is closed due to road construction.
Possible cause
The traffic information is not set to on.
The vehicle is in an area where traffic information is not available.
The subscription to NavTraffic is incomplete, or the subscription to NavTraffic has expired.
The map scale is set at a level where the display of icons is impossible.
Possible solution
Set the traffic information to on.
Scroll to an area where traffic information is available.
Check the subscription status of NavTraffic.
There is no faster route compared to the current route, based on the road network and traffic information.
The navigation system is designed not to avoid this event because the actual period of closure may differ from the declared roadwork period.
Check that the map scale is set at a level in which the display of icons is possible.
“Traffic information display and scale levels” (page 7-19)
The automatic detour search is not intended for avoiding traffic jams.
It searches for the fastest route taking into consideration such things as traffic jams. Follow the current route. Also see “Notes on NavTraffic information” for further information.
“Notes on NavTraffic information” (page 10-14)
Observe the actual road conditions and follow the instructions on the road for detour when necessary. If the road actually is closed, use the detour function and set the detour distance to avoid the road section that is closed.
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
11-11
Black plate (254,1)
11. Troubleshooting guide
MEMO
11-12
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
CURRENT LOCATION MAP SCREEN
Index
<ENTER> Store Location
Nearby Places
Map View Change View
View Settings
Map Settings
2D Map
Split: 2D Map
Birdview (3D)
Split: Birdview Map
Intersection
Turn List
Fuel Economy
Full Map
Map Orientation
Long Range
Map Color
Birdview Angle
Left Split Map Settings
Black plate (255,1)
Index page 6-2 page 4-6 page 3-11 page 3-11 page 3-11 page 3-11 page 5-10 page 5-10 page 5-10 page 5-10 page 3-14 page 3-15 page 3-16 page 3-16 page 3-17
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
12-1
Index
<ENTER> Map View
Map Icons
Store Tracking
Black plate (256,1)
Map Settings
Restaurant
Gas Station
Hotel
ATM
Rest Area
Show All Freeway Exits on
Route
Auto. Show Turn List on
Freeway page 5-11 page 5-11 page 3-18 page 3-18 page 3-18 page 3-18 page 3-18 page 6-6
12-2
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
SCROLL LOCATION MAP SCREEN
<ENTER> New Dest.
Add to Route
Nearby Places
Store Location
Delete
Incident Detail
Start
More Routes
Add/Route Info
Move Location
Store Location
Place Info
Black plate (257,1)
Index page 5-2 page 5-3 page 5-3 page 5-5 page 5-5 page 5-6 page 5-15 page 4-6 page 6-2 page 6-20 page 7-20
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
12-3
Black plate (258,1)
Index
DESTINATION SCREEN
<DEST> Change Region
Street Address
Places
Home
Address Book
Previous Destinations
Connected Search (if soequipped)
Next Page Delete Destination
Previous Start Point
Stored Routes
Phone Number
Freeway Entrance/Exit
Intersection
City Center
12-4
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ] page 4-3 page 4-4 page 4-6 page 4-11 page 4-12 page 4-13 page 4-14 page 4-24 page 4-16 page 4-17 page 4-18 page 4-19 page 4-20 page 4-22
ROUTE SCREEN
<ROUTE> Cancel Route/Resume Route
Edit/Add to Route
Route Info
Guidance Settings
Recalculate
Detour
Traffic Detour
Route Settings
Guidance Voice
Guidance Volume
Traffic Announcement
Basic Route Type
Other Routing Choices
Black plate (259,1)
Index page 5-14 page 5-15 page 5-20 page 5-21 page 5-21 page 5-21 page 5-22 page 5-23 page 5-24 page 5-25 page 5-26
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
12-5
Black plate (260,1)
Index
SETTING SCREEN
<SETTING> Navigation Address Book
Map View
Map Icons
Guidance Settings
Route Settings
Traffic Info Settings
Weather Info Settings
Speed Limit Info
Others
Delete Stored Information
Delete Connected Search History (if so equipped)
Delete All Previous Destinations
Delete All Previous Start Point
Reset All Navigation Settings to Default
12-6
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ] page 6-8 page 3-13 page 3-18 page 5-27 page 5-26 page 7-20 page 7-29 page 8-6 page 8-7 page 8-10 page 8-10 page 8-10 page 8-10 page 8-10
<SETTING> Audio
Phone
Bluetooth
Volume & Beeps
ECO DRIVE
Driver Assistance
Others Rear Display
Display
Comfort
Clock
Language & Units
Voice Recognition
Infiniti Connection TM (if so equipped)
Camera
Sonar
Image Viewer
Black plate (261,1)
Index
Vehicle Owner’s Manual
Vehicle Owner’s Manual
Vehicle Owner’s Manual page 8-11
Vehicle Owner’s Manual
Vehicle Owner’s Manual
Vehicle Owner’s Manual page 8-3
Vehicle Owner’s Manual page 8-12 page 8-13 page 9-15 page 7-12
Vehicle Owner’s Manual
Vehicle Owner’s Manual
Vehicle Owner’s Manual
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
12-7
Index
INFORMATION SCREEN
<INFO> Infiniti Connection (if so equipped)
Energy Flow
Fuel Economy
Tire pressure
Traffic Info
Weather Info
Others Where am I?
Maintenance
Map Update
Navigation Version
GPS Position
Voice Recognition
Black plate (262,1) page 7-3
Vehicle Owner’s Manual
Vehicle Owner’s Manual
Vehicle Owner’s Manual page 7-15 page 7-21 page 7-15
Vehicle Owner’s Manual page 7-30 page 7-31 page 7-32
“9. Voice recognition”
12-8
Condition: Language=NAM_English/ [ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
Number
A
Automatically
B
Birdview TM
Birdview TM
C
Condition: Language=NAM_English/
Black plate (263,1)
D
Changing Birdview TM
Character (letters and numbers)
Characteristics of liquid crystal
Command Lists (Alternate
Confirming how to use
Destination weather on suggested
Detailed Map Coverage Areas (MCA) for
Directions provided and distances to
Index
Displaying how to operate voice
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
12-9
Black plate (264,1)
Index
E H
F
G
12-10
Condition: Language=NAM_English/
I
INFINITI controller with
INFINITI controller without
L
M
Minor adjustment of home or
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
N
O
Operating with touch
P
Condition: Language=NAM_English/
Black plate (265,1)
R
Route calculation and visual
S
Searching for detour route taking traffic
Settings keyboard layout of character
Index
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
12-11
Black plate (266,1)
Index
T
Transferring information to/from
U
12-12
Condition: Language=NAM_English/
Using controls to adjust values,
Using voice
V
Viewing GPS current
Viewing information about current
Viewing information about
Viewing navigation system
W
What is GPS (Global
[ Edit: 2012/ 11/ 8 Model: 08TJ-N ]
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project