Range Hood

Model:HIH-T895

CONTENTS

4

5

6

7

8

1

2

3

Introduction

Safety and warnings

Installation instructions

About your rangehood

Operating instructions – Control panel

Cleaning and maintenance

Troubleshooting

Warranty

4

1 1

1 2

2

3

1 3

1 5

1 7

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this user guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please contact your local Haier dealer.

1

INTRODUCTION

Thank-you for purchasing a Haier range hood.

This user guide explains the features and functions, and will help you get the most out of your range hood.

We hope you enjoy your new range hood.

2

SAFETY AND WARNINGS

!

Electric Shock Hazard

Read and follow the safety and warnings outlined in this user guide before operating this appliance.

Never touch the power plug or electrical components, or manipulate the power switch with wet hands.

Altering of the internal wiring is strictly prohibited, unless performed by professional maintenance personnel.

When cleaning, never allow electrical components such as the motor, switch and connector to get wet.

Failure to do so can result in death, electric shock, fire or injury to persons.

Children should be supervised to ensure that they do not play with the appliance . Details for cleaning refer to part of ‘Cleaning and maintenance’.

IMPORTANT SAFETY INSTRUCTIONS

WARNING! When using this appliance always exercise basic safety precautions including the following:

●

Disconnect the power supply when cleaning or inspecting the product.

●

●

Do not damage or place heavy objects on the power cord.

There must be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels. (A partial vacuum in the room a concentration of gas in the air).

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

Never expose the range hood to a burner or element that is turned on without a pot or pan covering it.

If the hood is installed above the gas appliance, the minimum distance between the surface of the cooking vessel on the cooktop and the lowest part of the range hood should be at least 650mm. If the gas stove installation instructions specify a larger installation distance, this should be considered.

Never use aluminium foil on the cooktop.

If using shared ducting, the air outlet must be well secured and sealed.

burning gas or other fuels.

Do not flambe directly under the range hood.

Children and persons with reduced physical, sensory or mental capabilities shall not range hood without supervision.

This appliance can be used by children aged from 8 years and above and persons with reduced physical,sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

There is a fire risk if cleaning is not carried out in accordance with the instructions.

If installation is p erformed by a qualified person, the product should be tested to confirm proper operation, and the correct use of the product explained to the use . r.

If the power supply cord is damaged, it must only be replaced by your Haier trained and supported service technician or qualified person.

Use a dedicated power outlet; the power cord must not be connected to an extension cord or multi-socket power board. Secure grounding is required, and the power cord should be 2000mm in length.

Regulations regarding the discharge of air must be fulfilled.

This appliance is an external exhaust hood, air and smoke is discharged to the outside through

ensure the duct is straight.

contact your

Haier trained and supported service technician.

The appliance shall be able to work normally under the following environmental conditions: temperature -15°C ~ 40°C, relative humidity ≤ 90% (at 25°C), altitude ≤ 1000m.

●

●

Remove all packaging, including protective wrappings, before use.

CAUTION: Accessible parts may become hot when used with cooking appliances.

3

Contents of packaging

INSTALLATION INSTRUCTIONS

Range hood (1)

Haier

Range Hood

Model:HIH-T895

Installation guide

User guide (1)

Check valve assembly (1)

Check valve gasket (1)

Wall plate (1) Oil collector (1) Inner decorative cover holder (1)

Self-tapping screw

ST4 x 12 (4)

Cross recessed pan head screw

M4 x 20 (8)

Mounting screw*

5 x 50 (7)

Expansion plug*

8 x 40 (7)

Self-tapping screw ST3 x 8

(2)

4 will be required for other types of wall construction.

INSTALLATOIN INSTRUCTIONS

Names of principal components

Volute Fan Hand-tightened nut

Sealing ring Main housing Inner decorative cover

Outer decorative cover

Top cover Check valve assembly

Oil filter assembly LED Light (1)

5

INSTALLATION INSTRUCTIONS

Please read the entire instructions before installing the range hood.

Product dimensions

G

I

H

C

E F

A max

A min

B

PRODUCT DIMENSIONS

A Overall height of product

B Overall width of product

C Overall depth of product

D Height of canopy

E Width of flue

F Depth of flue

G Centre of ducting to left edge of product

H Centre of ducting to back edge of product

I Outside diameter of check valve assembly

6

IMPORTANT!

Actual product dimensions may vary by ± 2 mm.

D mm min. 610 – max. 990

895

520

80

375

320

370

170

185

Height of range hood

INSTALLATION INSTRUCTIONS

K

L

J

MINIMUM CLEARANCES

J Height top of gas cooktop to base of rangehood

K Height of rangehood installation if ducted through the ceiling if ducted through the rear

L Depth of rangehood installation mm min. 650 – max. 700 min. 610 min. 990

533

7

8

INSTALLATION INSTRUCTIONS

Installation

WARNING!

This product is heavy and requires two persons for installation.

WARNING!

Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

The manufacturer is not liable for any damage caused by not following these instructions.

1 Prepare the range hood for installation

●

Before commencement, unpack the range hood and check that it functions correctly.

●

●

●

●

The room in which the range hood is used should be well ventilated and contain no flammable, explosive or corrosive materials or articles.

The wall used for mounting the range hood should have sufficient strength and a flat surface.

When drilling holes in the wall, do so away from water, electricity or gas lines to prevent hazards such as electric shocks or gas leaks.

Temporarily mark the height of the bottom of the range hood and the centre of the cooktop on the wall according to the information given on page 8.

2 Install the wall plate

●

●

● locations of the wall plate holes and stopper screw holes as shown in Fig.1and 2.

Fit the expansion plugs into the holes.

Secure the wall plate to the wall using the mounting screws.

3 Install the decorative cover holder (if inner decorative cover extension is to be used)

●

●

●

Use an impact drill with a φ locations of the decorative cover holes as shown in Fig.1and 2.

Fit the expansion plugs into the holes.

Secure the decorative cover holder to the wall using the mounting screws.

Decorative cover holes

280 mm

Stopper screw hole

73 mm

224 mm

Wall plate holes

50 mm 50 mm

Fig.1

INSTALLATION INSTRUCTIONS

Fig.2

4 Install the supports

Attach the supports to the back of the range hood as shown in Fig.3.

Fig.3

9

10

INSTALLATION INSTRUCTIONS

5 Connect the check valve assembly

Place the check valve gasket and check valve assembly onto the air outlet on top of the main unit, and screw in place using the 8 cross recessed pan head screws.

6 Secure the main unit (this requires 2 persons)

Attach the main unit to the wall plate. Ensure the main unit and wall plate are firmly locked together.

7 Secure the stopper screw

Screw in the stopper screw at the top of the housing, ensuring that the screw is tightly secured against the main unit.

8 Connect the universal ducting hose

●

●

●

Insert the unmarked end of the universal ducting hose into the recess of the check valve, and secure to the check valve assembly with the self-tapping screws.

Connect the other end of the ducting hose to a shared flue or external wall hole.

The length of the universal ducting hose should not exceed 3 metres to prevent impact on venting performance. The number of bends should be minimised. Flexible ducting should be stretched tight and trimmed to suit the installation.

9 Extend the inner decorative cover (if inner decorative cover extension is to be used)

Pull the inner decorative cover up and hook it onto the decorative cover holder.

10 Fit the oil receptacle

●

●

Slide the oil receptacle into the slot on the oil cover .

Make sure the oil receptacle is pushed all the way in.

11 Remove packaging

Remove all protective wrappings.

ABOUT YOUR RANGEHOOD

Technical Data

LED Lamp

Type of Power

Motor Rated Power

Rated Power

Air flow

Air pressure

Input

Input

Noise

Universal Ducting Hose

Net Weight

Odour Removal Efficiency

Grease Separation

Off Power

Standb y Power

Total Pressure Efficiency

Input Power: 3 W ,Rated Voltage: 12 V

Cap Type: Buckle, Size: 220 mmX58 mm

Rated Voltage: 230V~ Rated Frequency: 50 Hz

219 W

222 W

Maximum air pressur e: ≥ 720 Pa

At Air Flow of 7 m³/min ≥ 260 Pa

58 dB(A)

Outer Diameter 180 mm, Length 1500 mm

31 Kg

Nominal ≥ 95 % Instantaneous ≥ 70%

≥ 90%

/

≤ 2 W

≥ 23%

11

OPERATING INSTRUCTIONS – CONTROL PANEL

CONTROL PANEL FEATURES

Turns the light on or off. Lighting switch operates independently

The front end of the collecting chamber forms an air curtain, preventing the oil smoke from spilling out from the front end of the range hood,so that the protecting user is not harmed by the oil smoke.

12 the fan speed is stepless variation.

Function 1: This key is for Boost function.

Press this button to switch to Boost speed for 30 seconds.

Function 2: This key is also for “Hood-Hob Connectivity” function.

(It needs to be matched up and work together with Haier Gas Hob which also has the same “Hood-Hob Connectivity” function)

(1) Match-up: While the Range Hood is at standby state, long press this

button for 5 seconds, after a "ding dong" sound, the key start to blink

for 15 seconds, within this 15 seconds, Rotate the Knob of the Hob,another

“Ding dong sound” mean the match-up is done.

(2) Hood-Hob Connectivity: After the match up is done, rotate the knob of

the Hob and start the fire ,the Range Hood will start to work automatically;

After turning off the knob of Hob, Range Hood will turn off automatically after 3 minutes.

(3) Disconnetion: At the standby state, long press this button for 5 seconds, after "ding dong" sound, the key quickly flashing for 3 seconds, meaning disconnection success.

Note: When the “Hood-Hob Connectivity” function is started, if touch the

sliding bar and select other wind speed, the Range Hood would execute according to the latest instruction and change speed accordingly, Remember

to turn off the Range Hood manually after usage because in this case,

“Hood-Hob Connectivity” function will not be effective for the turn-off

part.

Press this button the hood will connect to electricity.

When fan is on, press this button the hood will enter Delay off mode and turns off in 3 minutes.

In Delay off mode press this button to turn off the hood.

Hold “ ” for 5 seconds at power off feature, then “ ” blinking, start to activate the wifi connect mode, connect the range hood with APP, then range hood can be controled by mobile phone.

We recommend turning your r ange hood on before starting cooking for optimal performance.

CLEANING AND MAINTENANCE

●

●

●

●

●

●

●

We recommend following ‘Cleaning and maintenance’ instructions for safety and optimal performance of your range hood.

Preparation for cleaning and maintenance

Be sure to unplug the power cord before commencing cleaning or servicing of the range hood.

Always wear rubber gloves during cleaning and maintenance to guard against injury from sharp metal parts.

Always handle removed parts carefully to avoid damaging them.

Clean and service your range hood regularly, depending on the frequency of use.

Cleaning the main housing (daily)

The outer surface of the rangehood and filter should be wiped every day after use.

To protect the stainless steel finish, use a neutral detergent and a soft cloth. Never use hard brushes.

Never wipe surfaces with corrosive chemicals such as gasoline or alcohol, or abrasive cleaning agents.

●

●

●

●

●

Cleaning the oil receptacle (as necessary) i

When the oil receptacle reaches the mark, it should be removed promptly to avoid overflow.

Pull the oil receptacle straight out to detach

t rf o m t h e O i l C o v e .r

Empty the oil receptacle.

The oil receptacle should be washed in warm water with detergent (do not use corrosive chemicals).

To replace the oil receptacle slide it into the slot on the the way in.

●

●

●

●

●

●

C l e a n i n g t h e o i l c o v e r ( w e e k l y )

Remove oil receptacle (refer to instructions above).

Loosen the screw securing the oil cover

T h e o i l c o v e r s h o u l d b e w a s h e d i n warm water with detergent and left to soak. Wipe clean with a rag and rinse with fresh water.

T h e i cover n n e r p a r t o f t h e c o v e r a n d t h

recess in the main housing should be cleaned every week.

To reassemble; align the tabs and cover e angle the into the recess as shown in Fig.5. Insert the screw and tighten it using a screwdriver.

Slide oil receptacle into the slot on the and ensure it is pushed all the way in.

Fig.5

13

CLEANING AND MAINTENANCE

Cleaning the fan (every 3 months) (this requires 2 persons)

●

Remove the oil receptacle.

●

If the inner decorative cover has been extended, unhook it from the decorative cover holder and slide it back down between the main housing and outer decorative cover.

●

Loosen the screws attaching the ducting to the check valve assembly and remove the ducting from the check valve assembly.

●

Loosen the stopper screw and detach the main unit from the wall plate.

●

Remove the 4 screws that secure the outer decorative cover and remove the outer and inner decorative covers.

●

Loosen the screws holding the main housing cover plate and remove the cover plate.

●

Loosen the screws holding the intake ring and remove the intake ring.

●

Twist the nut in a clockwise direction to remove the fan.

●

Take particular care when cleaning the fan that the clips on the blades are not moved or lost, as this will imbalance the fan and cause vibration of the entire rangehood, leading to increased noise.

●

To reassemble replace the parts in reverse order of disassembly.

●

The fan should be cleaned once every 3 months.

14

Cleaning the entire unit (every 6 months) (this requires 2 persons)

●

The entire unit should be cleaned once every six months so as to maintain venting performance and ensure a long service life.

●

Unplug the power cord if the range hood will not be used for a prolonged period of time.

TROUBLESHOOTING

Solutions for common faults

In case of a fault, first try the suggestions below. If the problem cannot be fixed, please get in touch with your local Haier after-sales service centre. Only professional technicians may dismantle and repair the range hood.

PROBLEM

No power.

Product not working.

Light not working.

Product vibrates.

Poor suction

POSSIBLE CAUSE

Power supply plug is not plugged in or not properly connected.

No power is supplied to the electrical outlet.

Power is not connected or a fuse is blown.

The power supply is not connected, or the voltage is incorrect.

No fan speed has been selected.

Light button not pressed.

Light has burned out.

WHAT TO DO

Connect the power plug.

Restore the power supply or contact an electrician for repair.

Restore or contact an electrician for repair.

Restore the power supply or contact an electrician for repair.

Select a fan speed.

Main unit is not securely fastened to wall.

Fan is not well fitted.

Fan is damaged.

Press the light button.

Replace the light (please contact the after-sales service centre).

Check that the main unit is fastened securely.

Fit the fan properly.

Replace the fan (please contact the service centre).

Tighten the hand-tightened nut.

Hand-tightened nut is loose.

Windows and doors are open too wide during use or are closed.

Open or close doors and windows as necessary to ensure venting performance.

Range hood body is not installed at the correct height.

Re-install the appliance at the required height.

Reduce the length of the ducting hose or the number of bends.

Universal ducting hose is too long, has not been stretched tight, or has too many bends.

Shared flue aperture is too narrow or the air outlet is poorly sealed.

Widen the flue aperture or improve the outlet sealing.

The check valve blade is stuck and cannot function properly.

Range hood has not been cleaned.

Fix the blade and ensure the valve is working correctly.

Clean the range hood in accordance with the instructions.

15

16

TROUBLESHOOTING

PROBLEM

Oil leak.

Oil Cover is difficult to remove.

POSSIBLE CAUSE

Too much oil in the oil receptacle.

Oil cover has not been cleaned.

Main housing hasn't been cleaned.

Cover and cover recess have not been cleaned.

WHAT TO DO

Remove waste oil in the oil receptacle.

Clean the oil cover in accordance with the instructions.

Wipe the main housing every day after use in accordance with the instructions.

Clean the oil cover and cover recess weekly in accordance with the instructions.

Note: if you are unable to fix the problem by following the above prompts, or one of the situations below occurs, please unplug the range hood straight away and contact our after-sales service centre.

1 The range hood runs unevenly when turned on;

2 The range hood makes an unusual noise during operation;

3 Strange odours, heat or smoke are discovered, or other unusual circumstances not mentioned above occur.

The following phenomenon is not a malfunction

PHENOMENON

The product makes a clicking noise after the power is switched off for a few seconds.

CAUSE

Air pressure causes the two blades of the check valve to open during operation. After the power supply is switched off, the fan gradually stops rotating and the blades fall back by themselves, emitting a clicking noise.

Customer Name :-

……………………………………………..

Address :-

……………………………………………………………………………………………....

Serial Number :-

……………………………………………..

Date of Purchase :-

……………………………

Model No. :-

………………….…………………..

Dealer Seal :- ………………………………………………..

HAIER WARRANTY

HAIER APPLIANCES (INDIA) PVT. LTD . (here-in-after referred to as “the Company”) hereby offers the following warranty to the original domestic purchaser commencing from the Date of the

Purchase (DOP) . The Company at its sole discretion, will free of charge repair or replace any defective part or parts which prove to be defective in workmanship and/or materials and not due to abnormal or improper usage

CONDITIONS OF WARRANTY

1) This warranty will be automatically terminated on the expiry of the warranty period from the Date of Purchase (DOP) .

2) The Company is not liable for any delay in servicing due to reasons beyond the control of the Company or any of its authorized service center.

3) Parts replaced or repaired under this warranty are warranted throughout the remaining of the original warranty period.

4) It is entirely left to the Company's discretion to repair/replace parts at the site of installation or at the authorized service center.

5) This warranty shall be strictly limited to the repairs or replacement of the defective part specified in warranty. This warranty shall not cover any consequential

or resulting liability.

6) This warranty shall not, in any case, extend towards payment of any monetary consideration whatsoever or replacement or return of the product.

7) The Company may repair/supply parts free of cost during the warranty period. This warranty does not cover any Excise duty, Central or Sales tax, Octroi and

other local taxes or levies on the components/parts.

8) The parts shall be replaced by functionally operating equivalent material only and not with brand new ones and are likely to be different from the one

originally fitted. The parts thus removed shall be taken back by the Company.

9) The Company reserves the right to retain any part or component replaced at its sole discretion during the warranty period.

10) In no event the Company or its authorized service center, be liable for any consequential damages or resulting liability, damage or loss arising directly or indirectly out of

any defect in the product .

11) This warranty is not valid in case of the following events.

a) If the Product has been Installed/Serviced/Repaired/Opened or Tampered by any unauthorized personnel.

b) If defects arise/caused by accidents, alteration, misuse, neglect, substitution of original components with spurious/non- genuine components, attacked by

household pest / rodents, fire, flood, earthquake, lightning and/or any other act of God/natural calamities.

c) The product is shitted outside India.

12) (a) For any service under this warranty beyond city/town/municipal limits from the Company/authorized service center, a fixed charge of Rs. 100 will be

collected from the customer in addition to the actual to and for charges by the shortest route.

(b) Service charges applicable after expiry of comprehensive warranty.

13) Any change of location or change in the ownership during the warranty period must be intimated in writing to the Company.

14) The Company's employees or its authorized representatives have no authority to vary the terms of this warranty

15) Brass burners valve carry warranty against any manufacturing defect for 60 months. Warranty is not applicable for De-coloration of the burners.

16) The warranty does not cover rust, oxidation, discoloration, scratches, and wear & tear, plastic, rubber, aesthetic, filters, Consumable parts.

17) HOB Tempered glass top have 24 Month warranty for any manufacturing defect. The warrant of glass become null & void in following conditions.

a) Glass breakage due to improper use or accidental damage.

b) Use of gas tandoor / Gas Oven / Dosa Tawa.

c) Sprinkling of water on hot Glass surface.

d) Other safety norms / precaution not followed.

18) This warranty is affected in New Delhi and claims, if any, shall be made only before the courts having jurisdiction in New Delhi and no claim shall be made

against the Company outside New Delhi not withstanding that the Appliance may have been sold or delivered elsewhere.

Segment

Warranty

Period Parts not Covered

BUILT - IN - HOB

HYBTID - HOB

TABLET - HOB (1 + 4 Yrs. On Burner & Valve )

HOOD damage, etc.

Glass, Duct Cover, Body, Filters, Oil

Collector & Cleaning, Bulbs, Switches,

Knobs, Plastic Parts, accidents or damage, etc.

BUILT - MWO 1 Year Comprehensive

Outer Body, Cavity, Door, Glass, Handle,

BUILT - IN - OVEN

BUILT - STERILIZER accidents or damage, etc.

1 Year Comprehensive

Haier Appliances (India) Pvt. Ltd.

Building -1, Okhla Industrial Estate Phase III, New Delhi -110020

Tel- +91-1139496000,30674000,

Fax: +91-11-30674088

1800-102-9999, 1800-419-9999

(Toll Free - 24x7)

Whatsapp : 855 304 9999

For Quick Connect to Haier India Scan QR Code

Customer Name :- ……………………………………………..

Address :- ……………………………………………………………………………………………....

Serial Number :-

……………………………………………..

Date of Purchase :-

……………………………

Model No. :-

………………….…………………..

Dealer Seal :-

………………………………………………..

HTW62/65-187 Series

HTW65/70 -1187 Series

HTW70-178/186 Series

HM76-1159 Series

HTW80-1128/1159 Series

HTW82-178 Series

HTW85-186/178 Series

HM92-178 Series

HM95-186/178 Series

HTW100-178 Series

Peri0d

Comprehensive -12 Months

Motor - 60 Montfis p jgpq{

GwM

Comprehensive - 24 Months

/0\0f - 6/ /0fI!\8

Drain Pipe,

Inlet Pipe,

Lint Filter

Magic Filter