Meijer.com

Meijer.com

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure, that may be of sufficient magnitude to constitute a risk of electric.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instruction in the literature accompanying the appliance.

WARNING

USE UNDER SUPERVISION OF AN ADULT DUE TO LONG CORD

This unit has a long AC cord or other long cord that can easily be tripped on or pulled on, causing injury, Please make sure it is arranged so it will not drape over a tabletop,etc. Where it can be pulled on by children or tripped over accidentally.

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide residential protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and,if not Installed and used in accordance with the instructions,may cause harmful interference to radio communications.

However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmfull interference to radio or television reception. which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures: receiver.

c different from that to which the receiver is connected.

technician for help.

FCC NOTICE:

To assure continued compliance, follow the attached installation instructions and use only shielded cables when connecting to other devices. Modifications not authorized by the manufacturer may void user’s authority to operate this device.

All the safety and operating instructions should be read before the product is operated.

The safety and operating instructions should be retained for future reference.

All warnings on the product and in the operating instructions should be adhered to.

All operating and use instructions should be followed.

washbowl, kitchen sink or laundry tub; in a wet basement; or near a swimming pool.

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.

Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. this product should never be placed near or over a radiator or heat source. This product should not be placed in a built-in installation such as

This product should be operated only from the type of power source indicated on the marking label. If you are not sure the power supply, consult your appliance dealer or local power company. For products intended to operate from battery, or other sources refer to the operating instructions in this manual.

23. Wall or ceiling mounting

This product should be mounted to a wall or ceiling only as

recommended by the manufacturer.

can result in a risk of fire or electric shock.

Note:

Refer all servicing to qualified service personnel. Servicing is required when the unit has been damaged in any way such as the following: the power-supply cord or plug-in has been damaged, liquid has been spilled into the unit, the unit has been exposed to rain or moisture, the unit has been dropped or the unit does not operate normally.

3

5 4 9 10

8

6 7 1211

1 13 2 14

4. MEM/SET (Memory/Set) Button

5. POWER/FUNC (Power/Function) Button

6. Button

7. CH MODE (Channel mode) Button

8. SNOOZE/SLEEP/DIMMER Button

9. Button

10. VOL +/AL 1 (Volume up/Alarm 1) Button

11. VOL -/AL 2 (Volume down/Alarm 2) Button

12. Button

13. AUX IN Jack

14.Battery Door

Display and Indicators

AL 1 Indicator: Light when Alarm 1 is on.

AL 2 Indicator: Light when Alarm 2 is on.

PM Indicator: Light when the current time is PM.

Note: To save the batteries power in battery operating mode.

The display will turn off automatically when idle over than 5 minutes.

The unit is design to use the supplied AC/DC adaptor or 6 x AA size batteries (batteries not included).

Batteries:

To install or replace batteries:

1. Open the battery door on the rear of unit.

2. Install 6 (six) AA size batteries into the battery compartment as the polarity markings

inside.

3. Replace the battery door.

NOTES:

1.Alkaline batteries are recommended for longer operation time.

2.In battery operation mode,for saving the battery power the connected iPod/iPhone

will not be charging.

BATTERY PRECAUTIONS:

Follow these precautions when using a battery in this device:

1.Use only the size and type of battery specified.

2.Be sure to follow the correct polarity when installing the battery as indicated in the battery

compartment. A reversed battery may cause damage to the device.

3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old

batteries with fresh ones.

4.If the batteries in the device are consumed or the device is not to be used for a long period

of time, remove the batteries to prevent damage or injury from possible battery leakage.

5.Do not try to recharge the battery not intended to be recharged; it can overheat and

rupture. (Follow battery manufacturer’s instructions.)

6.Do not dispose of battery in fire. Battery may explodes or leak.

7.Clean the battery contacts and also those of the device prior to battery installation.

AC/DC Adaptor:

1. Insert the DC Plug from the supplied AC/DC Adaptor to the DC IN Jack on the rear of unit.

2. Insert the AC/DC Adaptor into wall outlet having AC 100-240V~, 50/60Hz

NOTES:

~ When AC/DC Adaptor was connected, the battery power will cut off automatically.

~ This AC/DC Adaptor is intended to be correctly orientated in a vertical or floor mount position.

~ When connected the iPod/iPhone to the docking, it will be charging automatically.

~ If Apparatus will not be used in a long period of time. To avoid damage the the unit. Unplug

the AC/DC Adaptor from the wall outlet and take out all batteries.

OPERATION

To set or reset the actual time:

1.Make sure the unit is in power off (standby) mode before setting.

2.Press and hold the MEM/SET Button on the front of unit until the digit of hour on

the display is blinking. Press the or Button to set the hour. (Make sure the

PM Indicator on the display is lit if the time is PM and not light if the time is AM).

3.Press the MEM/SET Button again; the digit of minute on the display will blink.

Press the or Button to set the Minute.

4.When finished, press the MEM/SET Button to save the settings and exit.

TIME SYNCHRONIZATION

The CMB3228 features a “CH MODE” button that allows you to set the time using the internal clock of the iPod/iPhone.

With the iPod/iPhone docked and power OFF, press the “CH MODE” button once.

NOTE:

When you first dock your iPod/iPhone, the unit will run an authentication process,

so it may not respond immediately to the “CH MODE” button when pressed. Wait

for a few seconds and try pressing the “CH MODE” button again.

An iPod/iPhone can only sync time up to the nearest minute; it’s possible to have up

to 59 seconds difference between the unit and synced iPod/iPhone.

The iPod internal clock is automatically updated when sync’d with iTunes. We

recommend you sync the iPod with iTunes prior to docking to CMB3228 to make

sure you have the current time available.

The iPhone receives constant updates from the phone service provider, so the

iPhone time will always be current.

The sync function can only be done when the CMB3228 power is Off.

Radio reception

1.Press the POWER/FUNC Button to turn on the unit.

Meijer.com

2.Press the POWER/FUNC Button repeatedly until Radio frequency appears on the display. Wait a

few seconds, you will hear sounds from speakers.

3.Press and hold the or Button until the displayed frequency starts running then release

the button. (When a radio station was been found, the frequency on display will stop running and

start to playback the searched station.) Press and release the or repeatedly to fine tune

if needed.

4.Repeat procedure 2 until the desiredd radio station was found.

5.Adjust the volume to the desiredd level by pressing VOL+/AL 1 or VOL–/AL 2 Button.

6.To power off (Standby mode) the unit, press and hold the POWER/FUNC Button until OFF

appear on the display then release the button.

ANTENNAS:

The Antenna wire on the rear cabinet is for radio reception. If reception is weak, unwind and extend the wire or relocate the wire to improve the radio reception.

RADIO STATION PRESETTING

1.Receive the desiredd radio station as the previous procedure.

2.Press the MEM/SET Button, "P XX" (XX is the last stored number of radio station) will appear on

the display and "XX" will be blinking. Press the or Button repeatedly to select the

desiredd location (CH 1 – CH 20) you want store to. Press the MEM/SET Button again to store.

3.Repeat the same procedure until all the desiredd radio stations were stored into the memory.

4.After settings, press the CH MODE Button to enter to Channel mode. "P XX" will appear on the

display. Press the or Buttons repeatedly to select the desiredd stored radio station.

Notes:

If AC/DC Adaptor has been unplugged from the wall outlet or the power supply failed, the preset

radio stations will be deleted.

The stored radio station only can be deleted by storing another new radio station.

Total 20 radio stations can be stored in the memory list.

In Radio mode, only the frequency of current radio station will appear on the display.

To view current time. Press Standby Button to power off the unit.

Docking and Charging The iPod/iPhone:

This unit is designed with the same connector found in most iPod and iPhone docks. When connecting the supported iPod/iPhone to the docking station on the top of the unit. The connecting iPod/iPhone will be start recharging. You can also playback the music files in the iPod/iPhone as follows:

1.Remove the cover of the iPod/iPhone Docking as shown on the figure below:

2.Insert the iPod/iPhone to the docking as shown below (If the power source of the unit is AC/DC

Adaptor. When iPod/iPhone is inserted, it will recharge automatically) :

3.Press the POWER/FUNC Button to turn on the unit.

4.Press the POWER/FUNC Button repeatedly until “IPod” appears on the display.

5.Press the >ll Button to start playback.

6.During playback:

A.Press VOL+/AL 1 or VOL–/AL 2 Button to adjust volume level as desired.

B.Press the Button to pause. Press again to resume normal playback.

C.Press the or Button to skipping tracks.

D.Press and hold the or Button to fast searching the desiredd section of current tracks.

7.To power off (Standby mode) the unit, press and hold the POWER/FUNC Button until OFF appear on the display, then release the button.

Note: If you have an earlier non-dockable iPod , connect it to the AUX IN jack as the AUX IN section follows.

AUX IN

To listen to the music from the external audio device or non-dockable iPods as follows:

1.Connect the external audio device or iPods/iPhone by an audio connection cable with 3.5mm

stereo plug on both ends (Cable not included).

2.Insert one end to the AUX Jack on the rear of unit. Insert the other end to the Phones Jack;

Line Out Jack or AUX Out Jack on the external audio device or iPods.

3.Press the POWER/FUNC Button to turn on the unit.

4.Press the POWER/FUNC Button repeatedly until “AU” appears on the display.

5.Playback the music in the connected external audio device or iPods as usual.

6.Press VOL+ or VOL– Button on the unit (and the connected unit) to adjust volume level as

desired.

7.To power off (Standby mode) the unit, press and hold the POWER/FUNC Button until OFF

appear on the display then, release the button.

ALARM SETTING

Alarm 1 setting:

1.Make sure the unit is in power off (standby) mode before setting.

2.Press and hold the VOL +/AL 1 Button for one second to enter setting mode. The AL 1

Indicator will light and Alarm 1 time will appear on the display (The digit of hour will be

blinking).

3.Press the or Buttons repeatedly to set the hour. (Make sure the PM Indicator on the

display is light if the alarm 1 time is PM and not light if it is AM).

4.Press the VOL +/AL 1 Button again, the digit of minute will be blinking. Press the or

Buttons repeatedly to set the minute.

5.Press the or Buttons repeatedly to set the wake up mode to buzz (b), Radio (F) or

iPod/iPhone (I).

6.Press the VOL +/AL 1 Button to enter, the volume level (two digits) will appear on the display.

Press the or Buttons to set the volume level as desired.

7.Press the VOL +/AL 1 Button to save the settings and exit.

Alarm 2 setting:

Same as Alarm 1 settings above. But, press the VOL -/AL 2 Button instead of press the VOL

+/AL 1 Button.

IMPORTANT NOTE:

Alarm will not operate when the unit is in power on mode.

If radio (F) was select, select the desired radio station as previous procedure before

activating alarm.

If iPod/iPhone mode was selected, make sure the iPod/iPhone was inserted in the

docking properly.

SHUT OFF ALARM:

When alarm goes off, press POWER/FUNC Button to turn it off , the alarm will

reset for next day.

To turn off the alarm completely (not reset for next day). Press the VOL +/AL 1 (VOL -/AL

2 Button), the AL 1 (AL 2) Indicator will turn off.

SNOOZE

The alarm can be temporarily turned off manually by pressing the

SNOOZE/SLEEP/DIMMER Button; the alarm will turn back on automatically nine (9) minutes later. This feature can be repeated until POWER/FUNC Button was pressed.

SLEEP

In the power on mode, press the SLEEP Button to activate the sleep function, SLEEP time will appear on the display. Press the SLEEP Button repeatedly to set the sleep timer to 10 –

90 minutes as desired.

To turn off the unit before sleep timer time up, press and hold the POWER/FUNC Button until “OFF” appear on the display.

Protect Your Furniture:

This model is equipped with non-skid rubber ‘feet’ to prevent the product from moving when you operate the controls. These ‘feet’ are made from non-migrating rubber material specially formulated to avoid leaving any marks or stains on your furniture. However certain types of oil based furniture polishes, wood preservatives, or cleaning sprays may cause the rubber ‘feet’ to soften, and leave marks or a rubber residue on the furniture. To prevent any damage to your furniture we strongly recommend that you purchase small self-adhesive felt pads, available at hardware stores and home improvement centers everywhere, and apply these pads to the bottom of the rubber ‘feet’ before you place the product on fine wooden furniture.

Meijer.com

AC/DC Adaptor is not plugged into a wall outled or the connector is not plugged into the DC IN jack on the back of the unit

Plug the AC/DC adaptor into wall outled and plug the connector into the DC IN jack on the unit.

Try others files.

General Specifications:

Power Source of Main Unit: DC 5V, 2.5A, Center positive

or 6 x AA size batteries (Not included).

AC/DC Adaptor:

Input:

Output:

Audio Power:

AC 100-240V~, 50/60Hz, 0. 5A

DC 5V, 2.5A, Center positive

Impendence of Speakers:

FM Radio Frequency Range:

2 x 2 W

4 Ohm; 3W x 2

88 – 108 MHz

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Accessory:

1 x User’s Manual

1 x AC/DC Adaptor

LIMITED WARRANTY

Craig warrants this product to be free from manufacturing defects in material and workmanship under normal use for a period of 90 days from date of purchase. If service is required, please return the product to the store where it was purchased for exchange; or, pack the unit in the original packing material with all accessories if applicable, a copy of your sales receipt and a Cashier’s check or Money Order for $12.00 (to cover shipping and handling costs) payable to Craig Electronics Inc. For consumers in Canada, please make sure that the cashier check or money order is redeemable through a U.S. bank.

Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit can not be repaired or replaced, a refund will be forwarded to you within four weeks of receipt of your unit. Please ship your unit to:

Craig Electronics Inc.

1160 NW 163 Drive

Miami, Fl 33169

This warranty is void if the product has been: a) Used in a commercial application or rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by anyone other than an authorized Craig service center. d) Damaged because it is improperly connected to any other equipment.

Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’s

Manual which can be performed by the customer. b) Damage to equipment not properly connected to the product. c) Any cost incurred in shipping the product for repair. d)

Damage to the product not used in the USA.

This warranty is not transferable and only applies to the original purchase. Any implied warranties, including the warranty of merchantability, are limited in duration to the period of this expressed warranty and no warranty whether expressed or implied shall apply to the product thereafter.

Under no circumstance shall Craig be liable for any loss or consequential damage arising out of the use of this product. This warranty gives specific legal rights. However, you may have other rights which may vary from state to state. Some states do not allow limitations on implied warranties or exclusion of consequential damage. Therefore, these restrictions may not apply to you.

Printed in China

To Obtain Service on your Product email:[email protected]

CMB3228-IB-E0AE1-B0KU