- Home
- Home security & automation
- Security device components
- JL Audio
- stealthbox sb-f-zx3-10w3
- Installation Guide
JL Audio stealthbox sb-f-zx3-10w3 Subwoofer Installation guide
Add to My manuals3 Pages
JL Audio Stealthbox SB-F-ZX3/10W3 is a product that requires professional installation skills and tools. It is a Stealthbox enclosure for the 2000-Up ZX3 2-door & 2001-Up ZX5 4-door hatchback. The enclosure is designed to house one JL AUDIO 10W3-D2 Subwoofer with a nominal impedance of 4Ω and a continuous power handling of 250 Watts. The enclosure type is Acoustic Suspension (Sealed). The Stealthbox SB-F-ZX3/10W3 comes with a 3/8” Washer, a 3/8” Lock Washer, a 3/8” Hex nut, and a 3/8” x 2 1/4” Socket Cup Set Screw.
advertisement
Stealthbox
®
I N S TA L L AT I O N G U I D E
for the
SB-F-ZX3/10W3
(2000-Up ZX3 2-door & 2001-Up ZX5
4-door hatchback)
START
HERE ➔
➔
➔
➔
➔
➔
➔ ➔
➔
➔
STEP 1: Remove the four Phillips head screws, panel button and cargo light from driver’s side rear cargo area.
STEP 2: Remove the plastic safety belt retractor cover. Look up under the plastic cover for a Phillips head screw. Remove this screw. (The location of this screw is shown in the picture by the upward arrow).
STEP 3: Remove the two plastic Phillips head screws indicated by the arrows.These are located in the driver’s rear hatch plastic trim panel. Remove the carpeted side panel.This
panel will be cut in Step 9 so as to form a trim for the Stealthbox.The view shown above is from the back seat looking toward the hatch. Also remove the hatch flooring (this flooring will be re-installed later).
This Stealthbox is a product that requires professional installation skills and tools.
Please read this installation guide thoroughly before beginning the project. It will guide you step by step through the installation. Several of the steps in this process may require two people to accomplish.
It is absolutely vital that the enclosure be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly presents two problems: 1) The sub-bass performance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s) and 2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration.
Please enjoy your JL Audio
Stealthbox responsibly.
➔
STEP 4: Locate the MOLEX ® plug and pull it loose from the side panel.
➔
➔
➔
STEP 5: Remove the T-27 TORX head bolt from the back side of the driver’s side rear wheel well. Remove the Phillips screw from directly below the TORX head bolt.
➔
.
STEP 6: Loosen the driver’s side rear fabric wheel well by pulling it toward the front of the car.
➔
Continued on Page 2
➔
S h e e t S K U # 0 1 1 1 5 7 R ev i s i o n 0 6 / 1 8 / 0 2 w w w . j l a u d i o . c o m S B - F - Z X 3 / 1 0 W 3 , J L AU D I O, I n c 2 0 0 2 Pa g e 1
Cont.
From
Page 1
➔ ➔
STEP 7: Pull plastic mounting stud out from the rear side metal panel were the MOLEX ® wiring plug was removed in Step 4.
STEP 8: Enlarge this hole to 1/2 in. (12.7 mm).
CAUTION: Always check for obstructions before drilling.
ALWAYS WEAR EYE PROTECTION
WHEN DRILLING.
➔
STEP 9: Using a measuring tape and masking tape, define the area to be cut as shown by the picture (above) and dimensions (to the right). All dimensions follow the contour of the panel.
A
B
E D
C
F
G
➔
H
A) 2.5 in. (63.5mm)
B) 1.0 in. (25.4mm)
C) 11.0 in. (279.4mm)
E) 1.25 in. (31.75mm)
F) 13.5 in. (342.9mm)
G) 9.375 in. (238.125mm)
D) 7.75 in. (196.85mm) H) 17.5 in. (444.5mm)
STEP 10: After panel has been cut, it should resemble this.
Continued on Page 3
➔
S h e e t S K U # 0 1 1 1 5 7 R ev i s i o n 0 6 / 1 8 / 0 2 w w w . j l a u d i o . c o m S B - F - Z X 3 / 1 0 W 3 , J L AU D I O, I n c 2 0 0 2 Pa g e 2
Cont.
From
Page 3 ➔
STEP 11: Reinstall the plastic side panel and the 4 Phillips head screws, the safety belt retractor cover and cargo light removed in
Steps 1 & 2. Place cut carpet side panel back into car.
➔
STEP 12: Run speaker wire to the location of the Stealthbox enclosure. At this time please check for proper operation of woofer.
STEP 13: Slide Stealthbox enclosure into the corner of cargo area. Insert the 3/8 in.
threaded mounting stud into the enclosure and line it up with the 1/2 in. (12.7 mm) hole.
Slide through to outside of car. Make sure relocated MOLEX ® plug and wiring is not going to be pinched by enclosure or side panels.
➔
STEP 14: From outside of the car, slide hand between the pulled fabric wheel well (Step
6) and the car’s body. Feel for the threaded mounting stud.
STEP 15: Place fender washer, lock washer and 3/8 in. nut onto threaded mounting stud.
➔
Tighten firmly using a 9/16 in. deep socket.
STEP 16: After securely mounting the
Stealthbox, push fabric wheel well back into place. Reinstall TORX head bolt and Phillips head screw that was removed in Step 5.
STEP 17: Replace hatch carpet back into car.You
will need to tuck the carpet under the Stealthbox.
CONGRATULATIONS!
INSTALL COMPLETE.
Included Hardware:
(1) 3/8” Washer
(1) 3/8” Lock Washer
(1) 3/8” Hex nut
(1) 3/8” x 2 1/4” Socket Cup Set Screw
Specifications:
Enclosure Type: Acoustic Suspension (Sealed)
Driver Type: One JL AUDIO 10W3-D2 Subwoofer
Nominal Impedance: 4
Ω
Cont. Power Handling: 250 Watts
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox ® .
+12VDC Ground Remote Preamp Output Section
Output Mode
Bass Control Amp LP Filter
Infrasonic Filter Mode/Slope
Amplifier Input Section
Input Voltage Input Sens.
Signal Sensing
Full-Range/Low-Pass/High-Pass
+1
+3
Off/30Hz
+7
+10
+13
Off/12dB/24dB Low/High Off/On
JL AUDIO 250/1 monoblock subwoofer amplifier
Left Ch.
Right Ch.
LF Boost (dB) Filter Freq. (Hz) Left Ch.
Right Ch.
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information about installing and tuning this amplifier.
Mid/High Frequency Driver Information:
Front Location Driver Size:
5"x7”
Applicable JL Audio Products:
TR570-CXi,
XR570-CXi or CSi
Rear Location Driver Size:
5"x7”
Applicable JL Audio Products:
TR570-CXi,
XR570-CXi or CSi
XR570-CXi
TR570-CXi
10369 N. Commerce Pkwy, Miramar, Florida 33025 Phone: 954.443.1100 Fax: 954.443.1111
S B - F - Z X 3 / 1 0 W 3 , J L AU D I O, I n c 2 0 0 2 Pa g e 3 S h e e t S K U # 0 1 1 1 5 7 R ev i s i o n 0 6 / 1 8 / 0 2 w w w . j l a u d i o . c o m
advertisement
Related manuals
advertisement