BenQ TH680 User manual

MH680/TH680

Digital Projector

User Manual

http://www.pureglare.com.au

2

Table of contents

Important safety instructions ........................... 3

Introduction.......................... 7

Projector features.....................................7

Shipping contents ......................................8

Projector exterior view...........................9

Controls and functions ..........................10

Positioning your projector..............................13

Choosing a location................................13

Obtaining a preferred projected image size..............................................................14

Connection .........................16

Connecting video source devices........17

Operation............................18

Starting up the projector ......................18

Adjusting the projected image .............19

Using the menus......................................21

Securing the projector...........................22

Switching input signal .............................24

Magnifying and searching for details ...25

Selecting the aspect ratio ......................25

Optimizing the image .............................27

Setting the presentation timer.............30

Remote paging operations ....................31

Freezing the image ..................................31

Hiding the image......................................32

Locking control keys ..............................32

Operating in a high altitude environment .............................................32

Adjusting the sound................................33

Using the test pattern ............................33

Table of contents http://www.pureglare.com.au

Using the teaching templates............... 34

Presenting from a USB Reader............ 35

Shutting down the projector ............... 36

Direct power off..................................... 36

Menu operation ...................................... 37

Maintenance........................ 47

Care of the projector............................ 47

Lamp information ................................... 48

Troubleshooting ................ 54

Specifications ...................... 55

Projector specifications......................... 55

Dimensions .............................................. 56

Ceiling mount installation..................... 56

Timing chart............................................. 57

Warranty and Copyright information ......................... 61

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1.

Please read this manual before

you operate your projector. Save it for future reference.

2.

Do not look straight at the

projector lens during operation.

The intense light beam may damage your eyes.

5.

In some countries, the line voltage is

NOT stable. This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In

areas where the mains voltage may fluctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply

(UPS).

3.

Refer servicing to qualified

service personnel.

6.

Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press

ECO BLANK on the projector or remote control.

4.

Always open the lens shutter (if any) or remove the lens cap (if any) when the projector lamp is

on.

Important safety instructions http://www.pureglare.com.au

3

Safety Instructions (Continued)

7.

The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.

10. Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage.

8.

Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions.

11. Do not attempt to disassemble this projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts. The only user serviceable part is the lamp which has its own removable cover.

Under no circumstances should you ever undo or remove any other covers. Refer servicing only to suitably qualified professional service personnel.

9.

Never replace the lamp assembly or any electronic components unless the projector is unplugged.

12. When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal phenomenon and not a product defect.

4 Important safety instructions http://www.pureglare.com.au


13. Do not place this projector in any of the following environments.

- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.

- Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.

- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten the projector's life span and darken the image.

14. Do not block the ventilation holes.

- Do not place this projector on a blanket, bedding or any other soft surface.

- Do not cover this projector with a cloth or any other item.

- Do not place inflammables near the projector.

- Locations near fire alarms

- Locations with an ambient temperature above 40°C / 104°F

- Locations where the altitudes are higher than 3000 m (10000 feet).

If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire.

15. Always place the projector on a level, horizontal surface during operation.

- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back. Using the projector when it is not fully horizontal may cause a malfunction of, or damage to, the lamp.

3000 m

(10000 feet)

0 m

(0 feet)

16. Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector.

Important safety instructions http://www.pureglare.com.au

5


17. Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury.

18. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's power outlet and call BenQ to have the projector serviced.

19. This product is capable of displaying inverted images for ceiling mount installation.

Use only BenQ's Ceiling Mount Kit for mounting the projector and ensure it is securely installed.

Ceiling mounting the projector

We want you to have a pleasant experience using your BenQ projector, so we need to bring this safety matter to your attention to prevent possible damage to person and property.

If you intend to mount your projector on the ceiling, we strongly recommend that you use a proper fitting BenQ projector ceiling mount kit and that you ensure it is securely and safely installed.

If you use a non-BenQ brand projector ceiling mount kit, there is a safety risk that the projector may fall from the ceiling due to an improper attachment through the use of the wrong gauge or length screws.

You can purchase a BenQ projector ceiling mount kit from the place you purchased your BenQ projector. BenQ recommends that you also purchase a separate Kensington lock compatible security cable and attach it securely to both the Kensington lock slot on the projector and the base of the ceiling mount bracket. This will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose.

Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.

20. This apparatus must be earthed.

6 Important safety instructions http://www.pureglare.com.au

Introduction

Projector features

The projector offers the following features

• Full HD compatible

The projector is compatible with Standard Definition TV (SDTV) 480i, 480p, 576i, 576p and High Definition TV (HDTV) 720p, 1080i and 1080p formats, with the 1080p format providing a true 1:1 image reproduction.

• SmartEco™ starts your dynamic power saving

The SmartEco™ technology offers a new way of operating the projector lamp system and saves lamp power depending on the content brightness level.

• Longest lamp life with SmartEco™ technology

The SmartEco™ technology lowers the power consumption and increases the lamp life.

• ECO BLANK saves the lamp power

Pressing the ECO BLANK button to hide the image and immediately lower the lamp power at the same time.

• Less than 0.5W in standby condition

Less than 0.5W power consumption under standby mode.

• Presenting from a USB Reader

This feature displays a slide show of images stored on a USB flash drive connected to the projector. It can eliminate the need for a computer source.

This feature allows the projector to display contents from your computer by using a single USB cable and without the need for any driver.

• Presenting from your mobile devices by Wireless Display

This feature allows a PC-free presentation with the help of an optional wireless dongle and the BenQ Qpresenter App. By selecting source Network Display in the OSD menu, you can start your presentation with your mobile devices without any wired connection!

• Quick Cooling, Auto Power Off, Signal Power On, Direct Power On

Quick Cooling function speeds up the cooling process when turning off the projector. Auto Power Off function allows the projector to turn off automatically if no input signal is detected after a set period of time. Signal Power On function turns on your projector automatically once detecting the signal input and Direct Power

On boots up the projector automatically when the power is connected.

• Instant Restart

Selectable Instant Restart function enables you to restart the projector immediately within 90 seconds after turning it off.

• 3D Function supported

Various 3D formats make the 3D function more flexible. By presenting the depth of the images, you can wear BenQ 3D glasses to enjoy the 3D movies, videos and sporting events in a more realistic way.

• The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected input signal contrast/brightness settings, and is directly proportional to projection distance.

• The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This is normal and expected behavior.

Introduction 7 http://www.pureglare.com.au

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those illustrated.

*The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.

Projector

Digital Projector

Quick Start Guide

Quick start guide

Power cord VGA cable

User manual CD Warranty card*

Remote control with batteries

Optional accessories

1.

Spare lamp kit

2.

Ceiling mount kit

3.

Carry bag

8 Introduction http://www.pureglare.com.au

Projector exterior view

21

22

3

4

Front/upper side

1

2

5

Rear/lower side

11

12 13 14 15 16 17 18 19

23

20

7

8

9

6

10

1.

External control panel

(See "Controls and functions" on page 10

for details.)

2.

Lamp cover

3.

Vent (heated air exhaust)

4.

Quick-release button

5.

Lens cap

6.

Focus and Zoom ring

7.

Vent (cool air intake)

8.

Speaker grill

9.

Front IR remote sensor

10. Projection lens

11. RS232 control port

12. USB ports

13. HDMI-input port

14. RGB signal output jack

15. RGB (PC)/Component Video (YPbPr/

YCbCr) signal input jack

16. S-Video input jack

Video input jack

17. Audio (L/R) input jacks

18. Audio input jack

19. Audio output jack

20. Kensington anti-theft lock slot

21. AC power jack

22. Rear adjuster foot

23. Ceiling mount holes http://www.pureglare.com.au

Introduction 9

Controls and functions

Projector

1

3

4

5

6

7

8

9

10

11

12

13

14

15

13

1.

Focus ring 11. LAMP indicator light

Adjusts the focus of the projected image.

2.

Zoom ring

Indicates the status of the lamp. Lights up or flashes when the lamp has developed a

Adjusts the size of the image.

problem.

3.

Top IR remote sensor

12. AUTO

4.

MENU/EXIT

Automatically determines the best picture

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, timings for the displayed image.

13. Keystone/Arrow keys ( / Up, /

exits and saves menu settings.

Down)

5.

POWER

Toggles the projector between standby mode and on.

14.

Manually corrects distorted images resulting from an angled projection.

Right/

6.

Left/

Increases the projector volume.

7.

Decreases the projector volume.

MODE/ENTER

When the On-Screen Display (OSD)

Selects an available picture setup mode.

Activates the selected On-Screen Display

(OSD) menu item.

select the desired menu items and to

8.

ECO BLANK

make adjustments.

15. SOURCE

Displays the source selection bar.

Used to hide the screen picture.

menu is activated, the #6, #13, and #14

keys are used as directional arrows to

9.

POWER indicator light

Lights up or flashes when the projector is under operation.

10. TEMPerature warning light

Lights up red if the projector's temperature becomes too high.


Remote control

1

2

3

4

12

13

14

9

10

11

8

7

5

6

19

20

21

22

23

7

15

16

17

18

18

1.

POWER

Toggles the projector between standby mode and on.

2.

Info

Shows the status information of the projector.

3.

MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

4.

Left

5.

MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display

(OSD) menu item.

6.

ECO BLANK

Used to hide the screen picture.

7.

Keystone/Arrow keys ( / Up, /

Down)

Manually corrects distorted images resulting from an angled projection.

8.

SmartEco

Displays the lamp mode selection bar.

9.

Aspect

Selects the display aspect ratio.

10. Page Up/Page Down

Operate your display software program (on a connected PC) which responds to page up/ down commands (like Microsoft

PowerPoint).

11. Digital Zoom (+, -)

Magnifies or reduces the projected picture size.

12. Timer On

Activates or displays an on-screen timer based on your own timer setting.

13. Timer Set up

Enters presentation timer setting directly.

14. 3D settings

Enters 3D settings directly.

15. AUTO

Automatically determines the best picture timings for the displayed image.

16.

Right

When the On-Screen Display (OSD) menu

is activated, the #4, #7, and #16 keys are

used as directional arrows to select the desired menu items and to make adjustments.

17. SOURCE

Displays the source selection bar.

18. Volume +/-

Adjusts the sound level.

19. Mute

Toggles projector audio between on and off.

20. Freeze

Freezes the projected image.

21. Quick Install

Quickly selects several functions to adjust the projected image and displays the test pattern.

22. CC

Displays the video term description on screen which is provided for hard-of-hearing viewers.

23. Teaching template

Enters Teaching template setting directly.

Introduction 11 http://www.pureglare.com.au

Remote control effective range

The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor(s) to function correctly. The distance between the remote control and the sensor(s) should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensor(s) on the projector that might obstruct the infra-red beam.

• Operating the projector from the front

• Operating the projector from the top

Appro x. +3

0º

Approx. +

30º

Replacing the remote control batteries

1.

To open the battery cover, turn the remote control over to view its back, push on the finger grip on the cover and slide it up in the direction of the arrow as illustrated.

The cover will slide off.

2.

Remove any existing batteries (if necessary) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive

(+) goes to positive and negative (-) goes to negative.

3.

Refit the cover by aligning it with the base and sliding it back down into position. Stop when it clicks into place.

• Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car.

• Replace only with the same or equivalent type recommended by the battery manufacturer.

• Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region.

• Never throw the batteries into a fire. There may be danger of an explosion.

• If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control from possible battery leakage.


Positioning your projector

Choosing a location

Your projector is designed to be installed in one of four possible installation locations:

1.

Front Table

Select this location with the projector placed on the table in front of the screen.

This is the most common way to position the projector for quick setup and portability.

3.

Rear Ceiling

Select this location with the projector suspended upside-down from the ceiling behind the screen.

Note that a special rear projection screen and the BenQ Projector Ceiling Mount Kit are required for this installation location.

Set Rear Ceiling in the SYSTEM

SETUP: Basic > Projector Installation menu after you turn the projector on.

2.

Front Ceiling

Select this location with the projector suspended upside-down from the ceiling in front of the screen.

Purchase the BenQ Projector Ceiling

Mount Kit from your dealer to mount your projector on the ceiling.

Set Front Ceiling in the SYSTEM

SETUP: Basic > Projector Installation menu after you turn the projector on.

4.

Rear Table

Select this location with the projector placed on the table behind the screen.

Note that a special rear projection screen is required.

Set Rear Table in the SYSTEM SETUP:

Basic > Projector Installation menu after you turn the projector on.

Your room layout or personal preference will dictate which installation location you select.

Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.

Positioning your projector 13 http://www.pureglare.com.au

Obtaining a preferred projected image size

The distance from the projector lens to the screen, the zoom setting, and the video format each factors in the projected image size.

Projection dimensions

Installation for a 16:9 ratio screen

Floor Installation

<A>



<F>

Ceiling Installation

<D>

<G>

<A>



<E>

<C>

<E>

<D>

<F>: Screen <G>: Center of lens

<G>

<F>

<C>


The screen aspect ratio is 16:9 and the projected picture is in a 16:9 aspect ratio

Screen dimensions Projection distance <D> [mm]

Diagonal

<A>

[inch (mm)]

Height



[mm]

Width

<C>

[mm]

Min distance

(with max zoom)

Average

Max distance

(with min zoom)

Lowest/

Highest lens position <E>

[mm]

40

50

60

70

80

90

(1016)

(1270)

(1524)

(1778)

(2032)

(2286)

100 (2540)

110 (2794)

120 (3048)

130 (3302)

140 (3556)

150 (3810)

160 (4064)

170 (4318)

180 (4572)

190 (4826)

200 (5080)

235 (5969)

1743

1868

1992

2117

2241

2366

2491

2926

498

623

747

872

996

1121

1245

1370

1494

1619

3099

3321

3542

3763

3985

4206

4428

5202

886

1107

1328

1550

1771

1992

2214

2435

2657

2878

3544

3797

4051

4304

4557

4810

5063

5949

1013

1266

1519

1772

2025

2278

2532

2785

3038

3291

4076

4367

4658

4949

5241

5532

5823

6842

1165

1456

1747

2038

2329

2620

2911

3203

3494

3785

4608

4937

5266

5595

5924

6253

6582

7734

1316

1646

1975

2304

2633

2962

3291

3620

3949

4278

112

118

125

146

87

93

100

106

62

68

75

81

25

31

37

44

50

56

14 Positioning your projector http://www.pureglare.com.au

Installation for a 4:3 ratio screen

The illustrations and table below are provided for those users who already have 4:3 aspect ratio screens or intend to purchase 4:3 aspect ratio screens to view 16:9 ratio projected images.

Floor Installation

<A>

<H>



<F>

<A>

Ceiling Installation

<H>

<E>

<D>

<G>

<C>

<E>

<D>


<F>

<C>




<G>

The screen aspect ratio is 4:3 and the projected picture is in a 16:9 aspect ratio

Screen dimensions

Diagonal

<A>

[inch (mm)]

Height



[mm]

Width

<C>

[mm]

Projection distance <D>

[mm]

Min distance

(with max zoom)

Average

Max distance

(with min zoom)

Lowest/

Highest lens position

<E>

[mm]

Image height

<H>

[mm]

40

50

60

70

80

(1016)

(1270)

610

762

(1524) 914

(1778) 1067

(2032) 1219

90 (2286) 1372

100 (2540) 1524

110 (2794) 1676

120 (3048) 1829

130 (3302) 1981

140 (3556) 2134

150 (3810) 2286

160 (4064) 2438

170 (4318) 2591

180 (4572) 2743

190 (4826) 2896

200 (5080) 3048

2091

2324

2556

2788

3021

3253

3486

3718

929

1162

1394

1627

1859

3950

4183

4415

4647

1829

2032

2235

2438

2642

2845

3048

3251

813

1016

1219

1422

1626

3454

3658

3861

4064

2719

3021

3323

3625

3927

4229

4531

4833

1208

1510

1813

2115

2417

5135

5438

5740

6042

2405

2672

2940

3207

3474

3741

4008

4276

1069

1336

1603

1871

2138

4543

4810

5077

5345

23 457

29 572

34 686

40 800

46 914

51 1029

57 1143

63 1257

69 1372

74 1486

80 1600

86 1715

91 1829

97 1943

103 2057

109 2172

114 2286

All measurements are approximate and may vary from the actual sizes.

BenQ recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.

Positioning your projector 15 http://www.pureglare.com.au

Connection

When connecting a signal source to the projector, be sure to:

1.

Turn all equipment off before making any connections.

2.

Use the correct signal cables for each source.

3.

Ensure the cables are firmly inserted.

• In the connections shown below, some cables may not be included with the projector (see

"Shipping contents" on page 8 ). They are commercially available from electronics stores.

• The connection illustrations below are for reference only. The rear connecting jacks available on the projector vary with each projector model.

Notebook or desktop computer

A/V device

Monitor

(VGA)

1 2

(DVI)

3 1 8

10

4 8 5 6 7

9 or

Speakers

8 or

1.

VGA cable

2.

VGA to DVI-A cable

3.

USB cable

4.

Component Video to VGA (D-Sub) adapter cable

5.

S-Video cable

6.

7.

8.

9.

Video cable

Audio L/R cable

Audio cable

USB flash drive/USB wireless dongle

10. HDMI cable

• Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/

LCD or a function key with a monitor symbol on the notebook. Press FN and the labeled function key simultaneously. Refer to your notebook's documentation to find your notebook's key combination.

• The D-Sub output only works when an appropriate D-Sub input is made to the COMPUTER 1 jack.

16 Connection http://www.pureglare.com.au

• If you wish to use this connection method when the projector is in standby mode, make sure the

Monitor Out function is turned on in the SYSTEM SETUP: Advanced menu. See

"Standby Settings" on page 46

for details.

Connecting video source devices

You need only connect the projector to a video source device using just one of the connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the video source device as described below:

Terminal name

HDMI

Terminal appearance Picture quality

Best

Component Video

Better

S-Video

Good

Video

Normal

Connecting audio

The projector has built-in mono speaker(s) which are designed to provide basic audio functionality accompanying data presentations for business purposes only. They are not designed for, nor intended for stereo audio reproduction use as might be expected in home theater or home cinema applications. Any stereo audio input (if provided), is mixed into a common mono audio output through the projector speaker(s).

The built-in speaker(s) will be muted when the AUDIO OUT jack is connected.

• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See

"Connecting audio" on page 17 for details.

• If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.


Connection 17

Operation

Starting up the projector

1.

Plug the power cord into the projector and into a power outlet. Turn on the power outlet switch

(where fitted). Check that the POWER indicator

light on the projector lights orange after power has been applied.

Please use the original accessories (e.g. power cord) only with the device to avoid possible dangers such as electric shock and fire.

2.

Press

On Ring Tone" will be heard. The POWER indicator light flashes green and stays green when the projector is on.

The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected.

(If necessary) Rotate the focus ring to adjust the image clearness.

To turn off the ring tone, see

"Turning off the Power On/Off Ring Tone" on page 33

for details.

If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.

3.

If the projector is activated for the first time, select your OSD language following the on-screen instructions.

4.

If you are prompted for a password, press the arrow keys to enter a six-digit

password. See "Utilizing the password function" on page 22

for details.

5.

Switch all of the connected equipment on.

6.

The projector will start to search for input signals. The current input signal being scanned appears in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message “No Signal” will continue displaying until an input signal is found.

You can also press SOURCE on the projector or remote control to select your desired input signal. See

"Switching input signal" on page 24 for details.

• If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message “Out of Range” displayed on the background screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See

"Timing chart" on page 57

for details.

• If no signal is detected for 3 minutes, the projector automatically enters ECO BLANK mode.

18 Operation http://www.pureglare.com.au

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot.

These adjusters change the image height and projection angle. To adjust the projector:

1.

Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position.

2.

Screw the rear adjuster foot to fine-tune the horizontal angle.

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see

"Correcting keystone" on page 20 for details.

1

2

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Be careful when you press the quickrelease button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto

Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

This function is only available when PC signal (analog RGB) is selected.

Fine-tuning the image size and clarity

1.

Adjust the projected image to the size that you need using the zoom ring.

2.

Sharpen the image by rotating the focus ring.


Operation 19

Correcting keystone

Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen.

To correct this, you will need to manually correct it following ONE of these steps.

• Press / on the projector or remote control to display the Keystone correction page.

Press to correct keystoning at the top of the image. Press to correct keystoning at the bottom of the image.

Press

/ .

Press

/ .

• Using the OSD menu

1.

Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.

Press correction page appears.

3.

Press to correct keystoning at the top of the image. Press keystoning at the bottom of the image.

to correct


Using the menus

The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.

The OSD screenshots below are for reference only, and may differ from the actual design.

Below is the overview of the OSD menu.

Main menu icon

Main menu

Sub-menu

DISPLAY

Wall Color

Aspect Ratio

Keystone

Position

Phase

H. Size

Digital Zoom

3D

Teaching Template

0

0

Off

Auto

ENTER

Status

Highlight

Current input signal

Analog RGB

MENU Exit

The following example describes how to set the OSD language.

1.

Press MENU/EXIT on the projector or remote control to turn the OSD menu on.

Press MENU/

EXIT to the previous page or to exit.

3.

Press and press MODE/ENTER.

DISPLAY

Wall Color

Aspect Ratio

Keystone

Position

Phase

H. Size

Digital Zoom

3D

Teaching Template

0

0

Off

Auto

SYSTEM SETUP: Basic

Presentation Timer

Language

Projector Installation

Menu Settings

Operation Settings

Remote Receiver

Panel Key Lock

Background Color

Splash Screen

ENTER

Front Table

Front+Top

Off

BenQ

BenQ

Analog RGB MENU Exit

2.

Use / to highlight the SYSTEM

SETUP: Basic menu.

SYSTEM SETUP: Basic

Presentation Timer

Language


Menu Settings

Operation Settings

Remote Receiver

Panel Key Lock


Splash Screen

Front Table

Front+Top

Off

BenQ

BenQ

Analog RGB MENU Exit

4.

Press / / / to select a preferred language.

5.

Press MENU/EXIT on the projector or remote control to leave and save the settings.

Analog RGB

MENU Exit

Operation 21 http://www.pureglare.com.au

Securing the projector

Using a security cable lock

The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock, such as the Kensington lock, to secure the projector. You can locate a Kensington

lock slot on the rear side of the projector. See item 23 on page 9 for details.

A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to the lock’s documentation for finding out how to use it.

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen

Display (OSD) menu.

WARNING: You will be inconvenienced if you activate the password functionality and subsequently forget the password. Print out this manual (if necessary) and write the password you used in this manual, and keep the manual in a safe place for later recall.

Setting a password

Once a password has been set and the power on lock is activated, the projector cannot be used unless the correct password is entered every time the projector is started.

1.

Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security

Settings menu. Press MODE/ENTER. The Security Settings page appears.

2.

Highlight Change Security Settings and press MODE/ENTER.

3.

As pictured to the right, the four arrow keys

INPUT NEW PASSWORD

( , , , ) respectively represent 4 digits

(1, 2, 3, 4). According to the password you desire to set, press the arrow keys to enter six digits for the password.

4.

Confirm the new password by re-entering the new password.

Once the password is set, the OSD menu returns to the Security Settings page.

MENU Back

5.

To activate the Power On Lock function, press / to highlight Power On Lock and press / to select On.

6.

To activate the Web Control Lock function, press / to highlight Web

Control Lock and press / to select On. When the Web Control Lock function is activated, you have to enter the correct password to change projector settings via the Projector Network Display System.

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

7.

To leave the OSD menu, press MENU/EXIT.


If you forget the password

If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right

Password Error

Please try again.

appears lasting for 3 seconds, and the INPUT

PASSWORD message follows. You can retry by entering another six-digit password, or if you did not record the password in this manual, and you absolutely do not remember it, you can use the password recall procedure. See

"Entering the password recall procedure" on page 23

for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.

Entering the password recall procedure

1.

Press and hold AUTO on the projector or remote control for 3 seconds. The projector will display a coded number on the screen.

2.

Write down the number and turn off your projector.

3.

Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

RECALL PASSWORD

Please write down the recall code, and contact BenQ

Customer Center.

Recall Code:

255 255 255 255

MENU

Exit

Changing the password

1.

Open the OSD menu and go to the SYSTEM SETUP: Advanced> Security

Settings > Change Password menu.

2.

Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears.

3.

Enter the old password.

i. If the password is correct, another message “INPUT NEW PASSWORD” appears. ii. If the password is incorrect, the password error message appears lasting for three seconds, and the message “INPUT CURRENT PASSWORD” appears for your retry. You can press MENU/EXIT to cancel the change or try another password.

4.

Enter a new password.

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

5.

Confirm the new password by re-entering the new password.

6.

You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

7.

To leave the OSD menu, press MENU/EXIT.


Disabling the password function

To disable password protection, go back to the SYSTEM SETUP: Advanced >

Security Settings > Change Security Settings menu after opening the OSD menu system. Press MODE/ENTER. The message “INPUT PASSWORD” appears. Enter the current password. i. If the password is correct, the OSD menu returns to the Security Settings page.

Press to highlight Power On Lock and press / to select Off. You will not have to enter the password next time when turning on the projector.

Press to highlight Web Control Lock and press / to select Off. Now the Web Control Lock is released and projector settings can be changed via the Projector Network Display System.

ii. If the password is incorrect, the password error message appears lasting for three seconds, and the message “INPUT PASSWORD” appears for your retry. You can press MENU/EXIT to cancel the change or try another password.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals.

Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals.

To select the source:

1.

Press SOURCE on the projector or remote control. A source selection bar appears.

2.

Press / until your desired signal is selected and press MODE/ENTER.

Computer1/YPbPr1

Computer2/YPbPr2

Once detected, the selected source information will display at the corner of the screen for seconds. If there is multiple equipment connected

to the projector, repeat steps 1-2 to search for

another signal.

HDMI

Video

S-Video

• The brightness level of the projected image will change accordingly when you switch between different input signals.

Data (graphic) "PC" presentations using mostly static images are generally brighter than "Video" using mostly moving images

(movies).

Network Display

USB Display

• The native display resolution of this projector is in a 16:9 aspect ratio. For best display picture results, you should select and use an input signal which outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the

USB Reader

“aspect ratio” setting, which may cause some image distortion or loss of picture clarity. See

"Selecting the aspect ratio" on page 25

for details.

• Firewall in the PC must be switched off to allow USB Display to work.


Changing Color Space

In the unlikely event that you connect the projector to a DVD player via the projector’s

HDMI input and the projected picture displays wrong colors, please change the color space to YUV.

To do this:

1.

Press MENU/EXIT and then press / until the SOURCE menu is highlighted.

2.

Press to highlight Color Space Conversion and press / to select a suitable color space.

This function is only available when the HDMI-input port is in use.

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture.

• Using the remote control

1.

Press Digital Zoom+/- to display the Zoom bar. Press Digital Zoom+ to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need.

2.

Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture.

3.

To restore the picture to its original size, press AUTO. You can also press Digital

Zoom-. When the key is pressed again, the picture is further reduced until it is restored to the original size.


1.

Press MENU/EXIT and then press

/

until the DISPLAY menu is highlighted.

2.

Press to highlight Digital Zoom and press MODE/ENTER. The Zoom bar appears.

3.

Press repeatedly to magnify the picture to a desired size.

4.

To navigate the picture, press MODE/ENTER to switch to the panning mode and press the directional arrows ( , , , ) on the projector or remote control to navigate the picture.

5.

To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/ out function, and press AUTO to restore the picture to its original size. You can also press repeatedly until it is restored to the original size.

The picture can only be navigated after it is magnified. You can further magnify the picture while searching for details.

Selecting the aspect ratio

The “aspect ratio” is the ratio of the image width to the image height. Most analog TV and some computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.

With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.

To change the projected picture ratio (no matter what aspect the source is):

• Using the remote control

1.

Press Aspect to show the current setting.


2.

Press Aspect repeatedly to select an aspect ratio to suit the format of the video signal and your display requirements.


1.

Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.

Press to highlight Aspect Ratio.

3.

Press / to select an aspect ratio to suit the format of the video signal and your display requirements.

About the aspect ratio

• In the pictures below, the black portions are inactive areas and the white portions are active areas.

• OSD menus can be displayed on those unused black areas.

1.

Auto

:

Scales an image proportionally to fit the projector's native resolution in its horizontal or vertical width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to make most use of the screen without altering the image's aspect ratio.

2.

Real

:

The image is projected as its original resolution, and resized to fit within the display area. For input signals with lower resolutions, the projected image will display smaller than if resized to full screen. You could adjust the zoom setting or move the projector towards the screen to increase the image size if necessary. You may also need to refocus the projector after making these adjustments.

15:9 picture

4:3 picture

16:9 picture

3.

4:3: Scales an image so that it is displayed in the center of the screen with a 4:3 aspect ratio. This is most suitable for 4:3 images like some computer monitors, standard definition

TV and 4:3 aspect DVD movies, as it displays them without aspect alteration.

4.

16:9: Scales an image so that it is displayed in the center of the screen with a 16:9 aspect ratio. This is most suitable for images which are already in a 16:9 aspect, like high definition

TV, as it displays them without aspect alteration.

5.

16:10: Scales an image so that it is displayed in the center of the screen with a 16:10 aspect ratio. This is most suitable for images which are already in a 16:10 aspect, as it displays them without aspect alteration.

4:3 picture

16:9 picture

16:10 picture


Optimizing the image

Using Wall Color

In the situation where you are projecting onto a colored surface such as a painted wall which may not be white, the Wall Color feature can help correct the projected picture’s colors to prevent possible color difference between the source and projected pictures.

To use this function, go to the DISPLAY > Wall Color menu and press / to select a color which is closest to the color of the projection surface. There are several precalibrated colors to choose from: Light Yellow, Pink, Light Green, Blue, and

Blackboard.

Selecting a picture mode

The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type.

To select an operation mode that suits your need, you can follow one of the following steps.

desired mode is selected.

• Go to the PICTURE > Picture Mode menu and press / to select a desired mode.

1.

Dynamic mode: Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms.

2.

Presentation mode: Is designed for presentations. The brightness is emphasized in this mode to match PC and notebook coloring.

3.

sRGB mode: Maximizes the purity of RGB colors to provide true-to-life images regardless of brightness setting. It is most suitable for viewing photos taken with an sRGB compatible and properly calibrated camera, and for viewing PC graphic and drawing applications such as AutoCAD.

4.

Cinema mode: Is appropriate for playing colorful movies, video clips from digital cameras or DVs through the PC input for best viewing in a blackened (little light) environment.

5.

3D mode: Is appropriate for playing 3D images and 3D video clips.

6.

User 1/User 2 mode: Recalls the settings customized based on the current available picture modes. See

"Setting the User 1/User 2 mode" on page 27 for details.

Setting the User 1/User 2 mode

There are two user-definable modes if the current available picture modes are not suitable for your need. You can use one of the picture modes (except the User 1/2) as a starting point and customize the settings.

1.

Press MENU/EXIT to open the On-Screen Display (OSD) menu.

2.

Go to the PICTURE > Picture Mode menu.

3.

Press

/

to select User 1 or User 2.

4.

Press to highlight Reference Mode.

This function is only available when User 1 or User 2 mode is selected up in the Picture Mode sub-menu item.

5.

Press / to select a picture mode that is closest to your need.


6.

Press to select a menu item to be changed and adjust the value with

/

. See

"Fine-tuning the image quality in user modes"

below for details.

Fine-tuning the image quality in user modes

According to the detected signal type and selected picture mode, some of the below functions may not be available. Based on your needs, you can make adjustments to these functions by highlighting them and pressing / on the projector or remote control.

Adjusting Brightness

The higher the value, the brighter the image. And the lower the setting, the darker the image. Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible.

Adjusting Contrast

The higher the value, the greater the contrast. Use this to set the peak white level after you have previously adjusted the Brightness setting to suit your selected input and viewing environment.

+30

-30

+50

0

+70

+30

Adjusting Color

Lower setting produces less saturated colors. If the setting is too high, colors on the image will be overpowering, which makes the image unrealistic.

Adjusting Tint

The higher the value, the more reddish the picture becomes. The lower the value, the more greenish the picture becomes.

Adjusting Sharpness

The higher the value, the sharper the picture becomes. The lower the value, the softer the picture becomes.

Adjusting Brilliant Color

This feature utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing truer, more vibrant colors in picture. It enables a greater than 50% brightness increase in mid-tone images, which are common in video and natural scenes, so the projector reproduces images in realistic and true colors. If you prefer images with that quality, select On. If you don’t need it, select Off.

When Off is selected, the Color Temperature function is not available.

Selecting a Color Temperature

The options available for color temperature* settings vary according to the signal type selected.

1.

Cool: Makes images appear bluish white.

2.

Normal: Maintains normal colorings for white.

3.

Warm: Makes images appear reddish white.

*About color temperatures:

There are many different shades that are considered to be "white" for various purposes.

One of the common methods of representing white color is known as the “color temperature”. A white color with a low color temperature appears to be reddish white. A white color with a high color temperature appears to have more blue in it.


Setting a preferred color temperature

To set a preferred color temperature:

1.

Highlight Color Temperature and select Warm, Normal or Cool by pressing

/ on the projector or remote control.

2.

Press Color Temperature Fine Tuning and press MODE/

ENTER. The Color Temperature Fine Tuning page appears.

3.

Press / to highlight the item you want to change and adjust the values by pressing / .

•

•

R Gain/G Gain/B Gain: Adjusts the contrast levels of Red, Green, and Blue.

R Offset/G Offset/B Offset: Adjusts the brightness levels of Red, Green, and

Blue.

4.

Press MENU/EXIT to exit and save the settings

3D Color Management

In most installation situations, color management will not be necessary, such as in classroom, meeting room, or lounge room situations where lights remain on, or where building external windows allow daylight into the room.

Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction, should you require it.

Proper color management can only be achieved under controlled and reproducible viewing conditions. You will need to use a colorimeter (color light meter), and provide a set of suitable source images to measure color reproduction. These tools are not provided with the projector, however, your projector supplier should be able to provide you with suitable guidance, or even an experienced professional installer.

The Color Management provides six sets (RGBCMY) of colors to be adjusted. When you select each color, you can independently adjust its range and saturation according to your preference.

If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc, you can project any image from the disc on the screen and enter the 3D Color Management menu to make adjustments.

To adjust the settings:

1.

Go to the PICTURE menu and highlight 3D Color Management.

2.

Press MODE/ENTER on the projector or remote control and the 3D Color

Management page appears.

3.

Highlight Primary Color and press / to select a color from among Red,

Yellow, Green, Cyan, Blue, or Magenta.

4.

Press highlight / to select its range. Increase in the range will include colors consisted of more proportions of its two adjacent colors.


Operation 29

Please refer to the illustration to the right for how the colors relate to each other.

For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta.

RED

5.

Press its values to your preference by pressing /

. Every adjustment made will reflect to the image immediately.

Magenta

For example, if you select Red and set its value at 0, only the saturation of pure red will be affected.

Yellow

BLUE

Cyan

GREEN

Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

6.

Press highlight /

. The contrast level of the primary color you select will be affected. Every adjustment made will reflect to the image immediately.

7.

Repeat steps 3 to 6 for other color adjustments.

8.

Make sure you have made all of the desired adjustments.

9.

Press MENU/EXIT to exit and save the settings.

Resetting current or all picture modes

1.

Go to the PICTURE menu and highlight Reset Picture Setting.

2.

Press MODE/ENTER and press / to select Current or All.

• Current: returns current picture mode to the factory preset settings.

• All: returns all settings, except User 1/User 2 in the PICTURE menu to the factory preset settings.

Setting the presentation timer

Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function:

1.

Go to the SYSTEM SETUP: Basic > Presentation Timer menu and press

MODE/ENTER to display the Presentation Timer page.

2.

Highlight Timer Period and decide the time period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-minute increments.

If the timer is already on, the timer will restart whenever the Timer Period is reset.

3.

Press to highlight Timer Display and choose if you want the timer to show up on the screen by press ing / .

Selection Description

Always Displays the timer on screen throughout the presentation time.

3 min/2 min/1 min Displays the timer on screen in the last 3/2/1 minute(s).

Never Hides the timer throughout the presentation time.


4.

Press highlight /

.

Top-Left Bottom-Left Top-Right Bottom-Right

5.

Press to highlight Timer Counting Direction and select your desired counting direction by pressing / .

Selection

Count Up

Count Down

Description

Increases from 0 to the preset time.

Decreases from the preset time to 0.

6.

Press reminder by pressing / . If you select On, a double beep sound will be heard at the last 30 seconds of counting down/up, and a triple beep sound will be produced when the timer is up.

7.

To activate the presentation timer, press and press / to highlight On and press MODE/ENTER.

8.

A confirmation message appears. Highlight Yes and press MODE/ENTER on the projector or remote control to confirm. You will see the message “Timer is On” displaying on the screen. The timer starts counting when the timer is on.

To cancel the timer, perform the following steps:

1.

Go to the SYSTEM SETUP: Basic > Presentation Timer menu and highlight

Off. Press MODE/ENTER. A confirmation message appears.

2.

Highlight Yes and press MODE/ENTER to confirm. You will see the message

“Timer is Off” displaying on the screen.

Remote paging operations

Connect the projector to your PC or notebook with a USB cable prior to using the paging function. See

"Connection" on page 16

for details.

You can operate your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint) by pressing Page Up/Page Down on the remote control.

If remote paging function doesn't work, check if the USB connection is correctly made and the mouse driver on your computer is updated to the latest version.

The remote paging function cannot work with Microsoft

® higher operating systems are recommended.

Windows

®

98 operating system. Windows

®

XP or

Freezing the image

Press Freeze on the remote control to freeze the image. The word “FREEZE” will display in the upper left corner of the screen. To release the function, press any key on the projector or remote control.

If your remote control has the following keys, please note that they cannot be pressed to release the function:

LASER, #1, #4, Page Up/Page Down.

Even if an image is frozen on the screen, the pictures are running on the video or other device. If the connected devices have active audio output, you will still hear the audio even though the image is frozen onscreen.


Hiding the image

In order to draw the audience's full attention to the presenter, you can use ECO BLANK on the projector or remote control to hide the screen image. When this function is activated with an audio input connected, the audio can still be heard.

You can set the blank time in the

SYSTEM SETUP: Basic > Operation Settings >

Blank Timer

menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen.

If the preset time spans are not suitable for your presentation, select Disable.

No matter

Blank Timer

is activated or not, you can press most of the keys on the projector or remote control to restore the picture.

Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire.

Locking control keys

With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When the Panel Key Lock is on, no control keys on the projector will operate except POWER.

1.

Go to the SYSTEM SETUP: Basic > Panel Key Lock menu, and select On by pressing / on the projector or remote control. A confirmation message appears.

2.

Highlight Yes and press MODE/ENTER to confirm.

To release panel key lock, use the remote control to enter the

SYSTEM SETUP:

Basic >

Panel Key Lock menu and press / to select

Off

.

• Keys on the remote control are still active when panel key lock is enabled.

• If you turn off the projector without disabling panel key lock, the projector will still be in locked status the next time it is turned on.

Operating in a high altitude environment

We recommend you use the High Altitude Mode when your environment is between

1500 m –3000 m above sea level, and ambient temperature is between 0°C–35°C.

Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under such a condition.

To activate the High Altitude Mode:

1.

Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.

Press highlight confirmation message appears.

/ select On. A

3.

Highlight Yes and press MODE/ENTER.

Operation under "High Altitude Mode" may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance.

If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from overheating. In cases like this, you should switch to High Altitude mode to solve these


symptoms. However, this is not to state that this projector can operate under any and all harsh or extreme conditions.

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speaker(s). Be sure you have made a correct connection to the projector audio input. See

"Connection" on page 16

for how the audio input is connected.

Muting the sound

To temporarily turn off the sound:

1.

Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.

Press

Settings page appears.

3.

Highlight Mute and press / to select On.

If available, you can also press Mute on the remote control to toggle projector audio between on and off.

Adjusting the sound level

To adjust the sound level, press Volume +/- or

1.

Repeat steps 1-2 above.

2.

Press

/

, or:

Turning off the Power On/Off Ring Tone

To turn off the ring tone:

1.

Repeat steps 1-2 above.

2.

Press

The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power On/Off Ring Tone.

Using the test pattern

The projector is able to display the grid test pattern. It helps you adjust the image size and focus and check that the projected image is free from distortion.

To display the test pattern, open the OSD menu and go to the SYSTEM SETUP: Advanced >

Test Pattern and press / to select On.


Operation 33

Using the teaching templates

The projector provides several preset patterns for various teaching purposes. To activate the pattern:

1.

Open the OSD menu and go to the DISPLAY > Teaching Template and press

/ to select Blackboard or Whiteboard.

2.

Press / to choose the pattern you need.

3.

Press MODE/ENTER to activate the pattern.

Teaching

Template

Whiteboard Blackboard

Letter

Formation

Worksheet

Coordinate

Chart


Presenting from a USB Reader

This feature displays a slide show of images stored on a USB flash drive connected to the projector. It can eliminate the need for a computer source.

Supported image formats:

• JPEG(JPG)

• BMP

• PNG

• GIF

• A square box will display on the filename for unidentified characters.

• TIFF

• Thai filename is not supported.

• Files in GIF, TIFF, PNG and BMP formats can be displayed for the file size smaller than WXGA (1280 x

800) only.

• If a folder consists of more than 200 photos, only the first 200 photos can be displayed.

To view your pictures as a slide show, follow these steps:

1.

Plug the USB flash drive into the USB TYPE-A jack of the projector.

2.

The projector automatically displays the thumbnails. Or you can manually select

USB Reader from the source selection bar.

When viewing thumbnails

To

open the folder scroll through thumbnails return to a previous page exit USB Reader change to a different page go back to the first page of that folder start a slide show adjust USB Reader settings

Press

Enter four arrow keys

Auto

Exit

/

Back

Slideshow when an image is highlighted.

Setting

During a slide show

To

go to the previous or next image rotate the image by 90 degree clockwise/ counterclockwise return to a previous page start/stop a slide show

Press

/

/

(Rotation is temporary; the image returns to its original orientation when you go back to thumbnails)

Auto

Enter

Setting page

You can adjust the file order and Slideshow settings. When you are done, press OK to save the settings or press Cancel to ignore the change.


Shutting down the projector

1.

Press

If you don't respond in a few seconds, the message will disappear.

2.

Press the projection lamp shuts down, and the fans will continue to run for approximately

90 seconds to cool down the projector.

To protect the lamp, the projector will not respond to any commands during the cooling process.

To shorten the cooling time, you can also activate the Quick cooling function. See "Quick Cooling" on page 44

for details.

3.

Once the cooling process finishes, a "Power Off

Ring Tone" will be heard. The POWER indicator

light is a steady orange and fans stop. Disconnect the power cord from the power outlet.

•

To turn off the power ring tone, see "Turning off the Power On/

Off Ring Tone" on page 33 for details.

• If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press POWER again to start the projector after the fans stop and the POWER indicator light turns orange.

• Lamp life results will vary depending on environmental conditions and usage.

Direct power off

The AC power cord can be pulled out right after the projector is turned off. To protect the lamp, wait about 10 minutes before re-starting the projector. (When you attempt to re-start the projector, the fans may run for a few minutes to cool down. In such cases, press POWER again to start the projector after the fans stop and the POWER indicator light turns orange.


Menu operation

Menu system

Please note that the on-screen display (OSD) menus vary according to the signal type selected and the projector model you are using.

Main menu Sub-menu

1.

DISPLAY

2.

PICTURE

3.

SOURCE

Wall Color

Aspect Ratio

Keystone

Position

Phase

H. Size

Digital Zoom

Off/Light Yellow/Pink/Light Green/Blue/

Blackboard

Auto/Real/4:3/16:9/16:10

3D

Color

Tint

Sharpness

Brilliant Color

Color Temperature

3D Mode

Auto/Top Bottom/Frame Sequential/

Frame Packing/Side by Side/Off

3D Sync Invert

Disable/Invert

Apply 3D

Settings

Save 3D Settings

3D Settings 1/3D Settings 2/3D Settings

3/Off

3D Settings 1/3D Settings 2/3D Settings

3

Teaching

Template

Blackboard

Whiteboard

Off/Letter Formation/Worksheet/

Coordinate Chart

Off/Letter Formation/Worksheet/

Coordinate Chart

Picture Mode

Dynamic/Presentation/sRGB/Cinema/(3D)/User 1/User 2

Reference Mode Dynamic/Presentation/sRGB/Cinema/(3D)

Brightness

Contrast

Color Temperature Fine Tuning

On/Off

Cool/Normal/Warm

R Gain/G Gain/B Gain/R Offset/G

Offset/B Offset

3D Color

Management

Primary Color

R/G/B/C/M/Y

Hue

Saturation

Gain

Reset Picture Setting

Quick Auto Search

Current/All/Cancel

On/Off

Color Space Conversion

Options

Auto/RGB/YUV



Presentation

Timer

Options

Timer Period

Timer Display

Timer Position

1~240 minutes

Always/3 min/2 min/1 min/Never

Top-Left/Bottom-Left/Top-Right/

Bottom-Right

Timer Counting

Direction

Count Down/Count Up

Sound Reminder On/Off

On/Off

Language

4.

SYSTEM

SETUP:

Basic


Menu Settings

Front Table/Rear Table/Rear

Ceiling/Front Ceiling

Menu Display

Time

5 sec/10 sec/20 sec/30 sec/Always

Menu Position

Center/Top-Left/Top-Right/Bottom-

Right/Bottom-Left

Reminder

Message

On/Off

Direct Power On On/Off

Operation

Settings

Remote Receiver

Panel Key Lock


Splash Screen

Signal Power On On/Off

Auto Power Off

Disable/3 min/10 min/15 min/20 min/25 min/30 min

Quick Cooling

Instant Restart

On/Off

On/Off

Blank Timer

Sleep Timer

Disable/5 min/10 min/15 min/20 min/25 min/30 min

Disable/30 min/1 hr/2 hr/3 hr/4 hr/8 hr/12 hr

Front+Top/Front/Top

On/Off

Black/Blue/Purple/BenQ

Black/Blue/BenQ



5.

SYSTEM

SETUP:

Advanced

6.

INFORMA

TION

Options

High Altitude Mode

Audio Settings

Lamp Settings

Mute

Volume

Power On/Off

Ring Tone

Lamp Mode

On/Off

On/Off

On/Off

Reset Lamp Timer

Equivalent Lamp

Normal/Economic/SmartEco

Security

Settings

Baud Rate

Change Password

Change Security

Settings

Power On Lock

Web Control Lock

2400/4800/9600/14400/19200/

38400/57600/115200

Test Pattern

Closed Caption

Standby

Settings

On/Off

Closed Caption

Enable

On/Off

Caption Version

CC1/CC2/CC3/CC4

Network

On/Off

Monitor Out

Audio Pass

Through

On/Off

Off/Audio In/Audio L/R/Network

Display/HDMI/USB Display

Network

Settings

Wireless LAN

Status

SSID

SSID Display

IP Address

Connection Mode

Apply

Reset All Settings

Projection Log In

Code

On/Off

Current System Status

• Source

• Picture Mode

• Lamp Mode

• Resolution

• 3D Format

• Color System

• Equivalent Lamp

• Firmware Version

Note that the menu items are available when the projector detects at least one valid signal.

If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.


Description of each menu

Function

Wall Color

Aspect Ratio

Keystone

Position

Description

Corrects the projected picture’s color when the projection surface is

not white. See "Using Wall Color" on page 27 for details.

There are several options to set the image's aspect ratio depending on

your input signal source. See "Selecting the aspect ratio" on page 25

for details.

Corrects any keystoning of the image. See

"Correcting keystone" on page 20 for details.

Displays the position adjustment page. To move the projected image, use the directional arrow keys. The values shown on the lower position of the page change with every key press you made until they reach their maximum or minimum.

This function is only available when a PC signal (analog RGB) is selected.

Adjusts the clock phase to reduce image distortion.

Phase

H. Size

Digital Zoom

This function is only available when a PC signal

(analog RGB) is selected.

Adjusts the horizontal width of the image.

This function is only available when a PC signal (analog RGB) is selected.

Magnifies or reduces the projected image. See "Magnifying and searching for details" on page 25 for details.


Function

3D

Teaching

Template

Description

This projector features a 3D function which enables you to enjoy the

3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images. You need to wear a pair of 3D glasses to view the 3D images.

3D Mode

The default setting is Auto and the projector automatically chooses an appropriate 3D format when detecting 3D contents. If the projector cannot recognize the 3D format, press / to choose a

3D mode.

When the 3D function is on:

• The brightness level of the projected image will decrease.

• The Picture Mode cannot be adjusted.

3D Sync Invert

When you discover the inversion of the image depth, enable this function to correct the problem.

Apply 3D Settings

After the 3D settings are saved, you can decide if you would like to apply them by choosing a set of 3D settings that you have saved. Once applied, the projector will automatically play the incoming 3D content if it matches the 3D settings saved.

Only the set(s) of 3D settings with memorized data is available.

Save 3D Settings

When you have successfully displayed the 3D content after making the appropriate adjustments, you can enable this function and choose a set of 3D settings to memorize current 3D settings.

See

"Using the teaching templates" on page 34

for details.


Operation 41

Function Description

Picture Mode

Reference

Mode

Brightness

Contrast

Pre-defined picture modes are provided so you can optimize your projector image set-up to suit your program type. See

"Selecting a picture mode" on page 27

for details.

Selects a picture mode that best suits your need for the image quality and further fine-tune the image based on the selections listed on the

same page below. See "Setting the User 1/User 2 mode" on page 27

for details.

Adjusts the brightness of the image. See "Adjusting Brightness" on page 28 for details.

Adjusts the degree of difference between dark and light in the image.

See

"Adjusting Contrast" on page 28 for details.

Adjusts the color saturation level -- the amount of each color in a video image. See

"Adjusting Color" on page 28

for details.

Color

This function is only available when a Video, S-Video or Component Video signal is selected.

Adjusts the red and green color tones of the image. See

"Adjusting

Tint" on page 28 for details.

Tint

This function is only available when a Video or S-Video signal is selected and the system format is NTSC.

Adjusts the image to make it look sharper or softer. See

"Adjusting

Sharpness" on page 28

for details.

Sharpness

This function is only available when a Video, S-Video or Component Video signal is selected.

Brilliant Color

See

"Adjusting Brilliant Color" on page 28

for details.

Color

Temperature

See

"Selecting a Color Temperature" on page 28 for details.

Color

Temperature

Fine Tuning

3D Color

Management

Reset Picture

Setting

See

"Setting a preferred color temperature" on page 29 for details.

See

"3D Color Management" on page 29

for details.

See

"Resetting current or all picture modes" on page 30 for details.


Function

Quick Auto

Search

Color Space

Conversion

Description

See "Switching input signal" on page 24 for details.

See "Changing Color Space" on page 25 for details.

Presentation

Timer

Language

Projector

Installation

Menu

Settings

Reminds the presenter to finish the presentation within a certain time

frame. See "Setting the presentation timer" on page 30 for details.

Sets the language for the On-Screen Display (OSD) menus. See

"Using the menus" on page 21 for details.

The projector can be installed on a ceiling or behind a screen, or with

one or more mirrors. See "Choosing a location" on page 13 for details.

Menu Display Time

Sets the length of time the OSD will remain active after your last key press.

Menu Position

Sets the On-Screen Display (OSD) menu position.

Reminder Message

Sets the reminder messages on or off.


Operation 43

Function

Operation

Settings

Description

Direct Power On

Allows the projector to turn on automatically once the power is fed through the power cord.

Signal Power On

Sets whether to turn the projector directly on without pressing

POWER or ON when the projector is in standby mode and the signal is feed through the VGA cable.

Auto Power Off

Allows the projector to turn off automatically if no input signal is detected after a set period of time. See

"Setting Auto Power Off" on page 48 for details.

Quick Cooling

Enables or disables the Quick Cooling function. Selecting On enables the function and projector cooling time will be shortened from a normal 90-second duration to approximately 15 seconds.

This function is only available when Instant Restart is off.

Instant Restart

Selecting On enables you to restart the projector immediately within

90 seconds after turning it off.

Blank Timer

Sets the image blank time when the Blank feature is activated, once elapsed the image will return to the screen. See

"Hiding the image" on page 32 for details.

Sleep Timer

Sets the auto-shutdown timer.

Allows you to enable all the remote receivers or one specific remote receiver on the projector.

Remote

Receiver

Panel Key

Lock

Background

Color

Splash

Screen

Disables or enables all panel key functions except POWER on the projector and keys on the remote control. See

"Locking control keys" on page 32 for details.

Sets the background color for the projector.

Allows you to select which logo screen will display during projector start-up.


Function

High

Altitude

Mode

Description

A mode for operation in high altitude areas. See

"Operating in a high altitude environment" on page 32

for details.

Audio

Settings

See

"Adjusting the sound" on page 33 for details.

Closed

Caption

Lamp Mode

See

"Setting the Lamp Mode" on page 48 for details.

Lamp

Settings

Reset Lamp Timer

See

"Resetting the lamp timer" on page 51 for details.

Equivalent Lamp

See "Getting to know the lamp hour" on page 48 for details on how the

total lamp hour is calculated.

Change Password

Change Security Settings

Power On Lock

See

"Utilizing the password function" on page 22 for details.

Security

Settings

Baud Rate

Web Control Lock

See BenQ Network Projector Operation Guide for details.

Selects a baud rate that is identical with your computer’s so that you can connect the projector using a suitable RS-232 cable and update or download the projector’s firmware. This function is intended for qualified service personnel.

Test Pattern

See

"Using the test pattern" on page 33

for details.

Closed Caption Enable

Activates the function by selecting On when the selected input signal carries closed captions.

• Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned

(usually marked as "CC" in TV listings).

Caption Version

Selects a preferred closed captioning mode. To view captions, select

CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary language in your area).


Operation 45

Function

Standby

Settings

Network

Settings

Reset All

Settings

Current

System

Status

Description

Network

Selecting On enables the function. The projector is able to provide the network function when it is in standby mode.

Monitor Out

Selecting On enables the function. The projector can output a VGA signal when it is in standby mode and the COMPUTER 1 jack is correctly connected to devices. See

"Connection" on page 16 for how

to make the connection.

Audio Pass Through

The projector can play sound when it is in standby mode and the corresponding jacks are correctly connected to devices. Press / to

choose the source that you wish to use. See "Connection" on page 16

for how to make the connection.

Enabling this function slightly increases the standby power consumption.

See BenQ Network Projector Operation Guide for details.

Returns all settings to the factory preset values.

The following settings will still remain: Phase, H. Size, Projector

Installation, Color Space Conversion, High Altitude Mode, Security

Settings and Baud Rate.

Source

Shows the current signal source.

Picture Mode

Shows the selected mode in the PICTURE menu.

Lamp Mode

Shows the current lamp mode.

Resolution

Shows the native resolution of the input signal.

3D Format

Shows the current 3D mode.

Color System

Shows input system format.

Equivalent Lamp

Displays the number of hours the lamp has been used.

Firmware Version

Shows the firmware version of your projector.


Maintenance

Care of the projector

Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens and case clean.

Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing.

Cleaning the lens

Clean the lens whenever you notice dirt or dust on the surface. Please be sure to turn off the projector and let it cool down completely before cleaning the lens.

• Use a canister of compressed air to remove dust.

• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.

• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the projector surface and cabinet material.

Cleaning the projector case

Before you clean the case, turn the projector off using the proper shutdown procedure as described in

"Shutting down the projector" on page 36 and unplug the power cord.

• To remove dirt or dust, wipe the case with a soft, lint-free cloth.

• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH detergent. Then wipe the case.

Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.

Storing the projector

If you need to store the projector for an extended time, please follow the instructions below:

• Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to

"Specifications" on page 55

or consult your dealer about the range.

• Retract the adjuster feet.

• Remove the battery from the remote control.

• Pack the projector in its original packing or equivalent.

Transporting the projector

It is recommended that you ship the projector with its original packing or equivalent.


Maintenance 47

Lamp information

Getting to know the lamp hour

When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer.

To obtain the lamp hour information:

1.

Press MENU/EXIT and then press / to highlight the SYSTEM SETUP:

Advanced menu.

2.

Press Lamp Settings and press MODE/ENTER. The Lamp

Settings page appears.

3.

You will see the Equivalent Lamp information displaying on the menu.

4.

To leave the menu, press MENU/EXIT.

You can also get the lamp hour information on the INFORMATION menu.

Extending lamp life

The projection lamp is a consumable item that normally can last up to 3000-4000 hours with proper usage. To keep the lamp life as long as possible, you can do the following settings via the OSD menu.

• Setting the Lamp Mode

Setting the projector in Economic or SmartEco mode extends the lamp operation life.

To set Economic or SmartEco mode, go into the SYSTEM SETUP: Advanced >

Lamp Settings > Lamp Mode menu and press / .

Lamp mode Description

Normal

Provides full lamp brightness

Economic

Lowers brightness to extend the lamp life and decreases the fan noise

SmartEco

Adjusts the lamp power automatically depending on the content brightness level

• Setting Auto Power Off

This function allows the projector to turn off automatically if no input signal is detected after a set period of time to prevent unnecessary waste of lamp life.

To set Auto Power Off, go into the SYSTEM SETUP: Basic > Operation Settings

> Auto Power Off menu and press / . If the preset time lengths are not suitable for your presentation, select Disable. The projector will not automatically shut down in a certain time period.

48 Maintenance http://www.pureglare.com.au

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

Go to http://lamp.benq.com

for a replacement lamp.

The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot.

Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after

turning the power back on, please contact your dealer. See "Indicators" on page 53

for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Install a new lamp for optimal performance. If the projector is normally run with Economic

selected (See "Getting to know the lamp hour" on page 48 ), you may continue to operate the

projector until the next hour lamp warning appears.

Press MODE/ENTER to dismiss the message.

Notice

Message

Order Replacement Lamp

Lamp>XXXX Hours

Order a new lamp at lamp.benq.com

OK

It is strongly recommended that you replace the lamp at this age. The lamp is a consumable item.

The lamp brightness diminishes with use. This is normal lamp behavior. You can replace the lamp whenever you notice that the brightness level has significantly diminished.


Notice

Replace Lamp Soon

Lamp>XXXX Hours


OK

Notice

Replace Lamp Now

Lamp>XXXX Hours

Lamp usage time exceeded


OK

The lamp MUST be replaced before the projector will operate normally.


WARNING

Out of Lamp Usage Time

Replace lamp (Refer to user manual)

Then reset lamp timer


OK

"XXXX" shown in the above messages are numbers that vary depending on different models.

Maintenance 49 http://www.pureglare.com.au

Replacing the lamp

• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp.

• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.

• To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces.

• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed.

• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner.

• To assure optimal performance from the projector, it is recommended that you purchase a qualified projector lamp for lamp replacement.

• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by fractured lamp.

• Ensure good ventilation when handling broken lamps. We recommend that you use respirators, safety glasses, goggles or face shield and wear protective clothing such as gloves.

1.

Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2.

Loosen the screw that secures the lamp cover on the side of the projector until the lamp cover loosens.

3.

Remove the lamp cover from the projector.

• Do not turn the power on with the lamp cover removed.

• Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

4.

Loosen the screw that secures the lamp.

5.

Lift the handle so that it stands up.

1

2


6.

Use the handle to slowly pull the lamp out of the projector.

• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

• Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

7.

As shown in the figure, lower the new lamp.

8.

Tighten the screw that secures the lamp.

9.

Ensure the handle is fully laid flat and locked in place.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

10. Replace the lamp cover on the projector.

2

1

11. Tighten the screw that secures the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

12. Connect the power and restart the projector.

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

13. After the startup logo, open the On-Screen Display (OSD) menu. Go to the

SYSTEM SETUP: Advanced > Lamp Settings menu. Press MODE/ENTER.

The Lamp Settings page appears. Highlight Reset Lamp Timer. A warning

Maintenance 51 http://www.pureglare.com.au

message appears asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to “0”.

Do not reset if the lamp is not new or replaced as this could cause damage.


Indicators

Light Status & Description

Red

Red

Red

Red

Green

Green

Green

Green

Green

Flashing

Green

Flashing

Green

Flashing

Green

Flashing

Orange

Green

Flashing

Green

Orange

Flashing

Red

Green

Red Flashing

Off

Off

Off

Off

Off

Off

Off

Off

Off

Off

Off

Red

Red

Flashing

Green

Green

Flashing

Red

Red

Flashing

Green

Green

Flashing

Red

Red

Flashing

Green

Green

Flashing

Off

Power events

Stand-by mode.

Off

Off

Powering up.

Normal operation.

Off

Normal power-down cooling

Off

Red

Off

Download

CW start fail

Scaler shutdown fail (data abort)

Lamp events

Red

Orange

Flashing

Lamp1 error in normal operation

Lamp is not lit up

Thermal events

Off

Off

Off

Off

Off

Fan 1 error (the actual fan speed is +25% outside the desired speed)




Temperature 1 error (over limited temperature)

Off

Off

Off

Thermal Sensor 1 open error

Thermal Sensor 1 short error

Thermal IC #1 I2C Connection error

Off

Off

Off

Off

Temperature 2 error (over limited temperature)

Thermal Sensor 2 open error

Thermal Sensor 2 short error

Thermal IC #2 I2C Connection error http://www.pureglare.com.au

Maintenance 53

Troubleshooting

The projector does not turn on.

Cause

There is no power from the power cord.

Attempting to turn the projector on again during the cooling process.

No picture

Remedy

Plug the power cord into the AC power jack on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on.

Wait until the cooling down process has completed.

Cause

The video source is not turned on or connected correctly.

The projector is not correctly connected to the input signal device.

The input signal has not been correctly selected.

The lens cover is still closed.

Blurred image

Remedy

Turn the video source on and check that the signal cable is connected correctly.

Check the connection.

Select the correct input signal with the SOURCE key on the projector or remote control.

Open the lens cover.

Cause

The projection lens is not correctly focused.

The projector and the screen are not aligned properly.

The lens cover is still closed.

Remote control does not work

Remedy

Adjust the focus of the lens using the focus ring.

Adjust the projection angle and direction as well as the height of the projector if necessary.

Open the lens cover.

Cause Remedy

The battery is out of power.

There is an obstacle between the remote control and the projector.

Replace the battery with new ones.

Remove the obstacle.

You are too far away from the projector.

Stand within 8 meters (26 feet) of the projector.

The password is incorrect

Cause

You do not remember the password.

Remedy

Please see

"Entering the password recall procedure" on page 23

for details.

54 Troubleshooting http://www.pureglare.com.au

Specifications

Projector specifications

All specifications are subject to change without notice.

Optical

Resolution

1920 (H) x 1080 (V)

Display system

1-CHIP DMD

Lens F/Number

F = 2.59 ~ 2.87, f = 16.88 ~ 21.88 mm

Lamp

210 W lamp

Control

RS-232 serial control

9 pin x 1

IR receiver x 2

Electrical

Power supply

AC100–240V, 3.1 A, 50-60 Hz

(Automatic)

Power consumption

315 W (Max); < 0.5 W (Standby)

Mechanical

Weight

2.8 Kg (6.39 lbs)

Output terminals

RGB output

D-Sub 15-pin (female) x 1

Speaker

(Stereo) 10 watt x 1

Audio signal output

PC audio jack x 1

Input terminals

Computer input

RGB input

D-Sub 15-pin (female) x 2

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1

SD/HDTV signal input

Analog - Component RCA jack x 3

(through RGB input)

Digital - HDMI x 1

Audio signal input

Audio in

RCA audio jack (L/R) x 2

PC audio jack x 1

USB ports (Type-A x 1; Mini-B x 1)

Environmental Requirements

Operating temperature

0°C–40°C at sea level

Operating relative humidity

10%–90% (without condensation)

Operating altitude

0–1499 m at 0°C–35°C

1500–3000 m at 0°C–30°C (with

High Altitude Mode on) http://www.pureglare.com.au

Specifications 55

Dimensions

311.81 mm (W) x 104.7 mm (H) x 244.12 mm (D)

244.12

104.7

311.81

Ceiling mount installation

Ceiling Mount screw: M4

(Max L = 25 mm; Min L = 20 mm)

Unit: mm

137

160

56 Specifications

95.21

168.59

311.58


111.28

239.77

Unit: mm

Timing chart

Supported timing for PC input

Resolution

640 x 480

720 x 400

800 x 600

1024 x 768

1152 x 864

1024 x 576

1024 x 600

1280 x 720

1280 x 768

1280 x 800

1280 x 1024

1280 x 960

1360 x 768

1440 x 900

1400 x 1050

1600 x 1200

1680 x 1050

640 x 480@67Hz

832 x 624@75Hz

1024 x 768@75Hz

1152 x 870@75Hz

Mode

VGA_60*

VGA_72

VGA_75

VGA_85

720 x 400_70

SVGA_60*

SVGA_72

SVGA_75

SVGA_85

SVGA_120**

(Reduce Blanking)

XGA_60*

XGA_70

XGA_75

XGA_85

XGA_120**

(Reduce Blanking)

1152 x 864_75

BenQ

Notebook_timing

BenQ

Notebook_timing

1280 x 720_60*

1280 x 768_60*

WXGA_60*

WXGA_75

WXGA_85

WXGA_120**

(Reduce Blanking)

SXGA_60***

SXGA_75

SXGA_85

1280 x 960_60***

1280 x 960_85

1360 x 768_60***

WXGA+_60***

SXGA+_60***

UXGA***

1680x1050_60***

MAC13

MAC16

MAC19

MAC21

Vertical

Frequency

(Hz)

59.940

72.809

75.000

85.008

70.087

60.317

72.188

75.000

85.061

119.854

60.004

70.069

75.029

84.997

119.989

75

60.0

64.995

60

59.87

59.810

74.934

84.880

119.909

60.020

75.025

85.024

60.000

85.002

60.015

59.887

59.978

60.000

59.954

66.667

74.546

74.93

75.060

Horizontal

Frequency

(kHz)

31.469

37.861

37.500

43.269

31.469

37.879

48.077

46.875

53.674

77.425

48.363

56.476

60.023

68.667

97.551

67.5

35.820

41.467

45.000

47.776

49.702

62.795

71.554

101.563

83.000

65.000

75.000

78.750

94.500

115.5

108

46.966

51.419

74.250

79.5

83.500

106.500

122.500

146.25

63.981

79.976

91.146

60.000

85.938

47.712

55.935

65.317

75.000

65.29

35.000

49.722

60.241

68.680

• *Supported timing for 3D signal in Frame Sequential, Top Bottom and Side by Side formats.

**Supported timing for 3D signal in Frame Sequential format.

***Supported timing for 3D signal in Top Bottom and Side by Side format.

108.000

135.000

157.500

108.000

148.500

85.5

106.500

121.750

162.000

146.25

30.240

57.280

80.000

100.000

Pixel

Frequency

(MHz)

25.175

31.500

31.500

36.000

28.3221

40.000

50.000

49.500

56.250

Specifications 57 http://www.pureglare.com.au

58

• The timings showing above may not be supported due to EDID file and VGA graphic card limitations. It is possible that some timings cannot be chosen.

Supported timing for HDMI (HDCP) input

Resolution

640 x 480

720 x 400

800 x 600

1024 x 768

1152 x 864

1280 x 768

1024 x 576@60Hz

1024 x 600@65Hz

1280 x 720

1280 x 768

1280 x 800

1280 x 1024

1280 x 960

1360 x 768

1440 x 900

1400 x 1050

1600 x 1200

1680 x 1050

640 x 480@67Hz

832 x 624@75Hz

1024 x 768@75Hz

1152 x 870@75Hz

Mode

VGA_60*

VGA_72

VGA_75

VGA_85

720 x 400_70

SVGA_60*

SVGA_72

SVGA_75

SVGA_85

SVGA_120**

(Reduce Blanking)

XGA_60*

XGA_70

XGA_75

XGA_85

XGA_120**

(Reduce Blanking)

1152 x 864_75

1280 x 768_60*

BenQ Notebook

Timing

BenQ Notebook

Timing

1280 x 720_60*

1280 x 768_60*

WXGA_60*

WXGA_75

WXGA_85

WXGA_120**

(Reduce Blanking)

SXGA_60***

SXGA_75

SXGA_85

1280 x 960_60***

1280 x 960_85

1360 x 768_60***

WXGA+_60***

SXGA+_60***

UXGA***

1680x1050_60***

MAC13

MAC16

MAC19

MAC21

Vertical

Frequency

(Hz)

Horizontal

Frequency

(kHz)

Pixel

Frequency

(MHz)

59.940 31.469 25.175

72.809 37.861 31.500

75.000 37.500 31.500

85.008 43.269 36.000

70.087

31.469

28.3221

60.317 37.879 40.000

72.188 48.077 50.000

75.000 46.875 49.500

85.061 53.674 56.250

119.854

60.004 48.363 65.000

70.069 56.476 75.000

75.029 60.023 78.750

84.997 68.667 94.500

119.989

75

59.87

60.00

64.995

60

59.870

59.810

74.934

84.880

119.909

77.425

97.551

67.5

47.776

35.820

41.467

45.000

47.776

49.702

62.795

71.554

101.563

83.000

115.5

108

79.5

46.996

51.419

74.250

79.5

83.500

106.500

122.500

146.25

60.020 63.981 108.000

75.025

79.976

135.000

85.024

60.000

85.002

60.015

91.146

60.000

85.938

47.712

157.500

108

148.500

85.500

59.887

59.978

60.000

59.954

66.667

74.546

75.020

75.06

55.935

65.317

75.000

65.290

35.000

49.722

60.241

68.68

106.500

121.750

162.000

146.250

30.240

57.280

80.000

100.00

• *Supported timing for 3D signal in Frame Sequential, Top Bottom and Side by Side formats.

**Supported timing for 3D signal in Frame Sequential format.

***Supported timing for 3D signal in Top Bottom and Side by Side formats.

Specifications http://www.pureglare.com.au

• The timings showing above may not be supported due to EDID file and VGA graphic card limitations. It is possible that some timings cannot be chosen.

Timing

480i*

480p*

576i

576p

720/50p**

720/60p***

1080/50i****

1080/60i****

1080/24P**

1080/25P

1080/30P

1080/50P*****

1080/60P*****

Resolution

720 x 480

720 x 480

720 x 576

720 x 576

1280 x 720

1280 x 720

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

Vertical

Frequency

(Hz)

59.94

59.94

50

50

50

60

50

60

24

25

30

50

60

Horizontal

Frequency

(kHz)

15.73

31.47

15.63

31.25

37.5

45.00

28.13

33.75

27

28.13

33.75

56.25

67.5

Pixel

Frequency

(MHz)

27

27

27

27

74.25

74.25

74.25

74.25

74.25

74.25

74.25

148.5

148.5

*Supported timing for 3D signal in Frame Sequential format.

**Supported timing for 3D signal in Top Bottom, Frame Packing and Side by Side formats.

***Supported timing for 3D signal in Frame Sequential, Top Bottom, Frame Packing and Side by Side formats.

****Supported timing for 3D signal in Side by Side format.

*****Supported timing for 3D signal in Top Bottom format.

Supported timing for Component-YP b

P r input

Timing

480i*

480p*

576i

576p

720/50p

720/60p*

1080/50i

1080/60i

1080/24P

1080/25P

1080/30P

1080/50P

1080/60P

Resolution

720 x 480

720 x 480

720 x 576

720 x 576

1280 x 720

1280 x 720

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

Vertical

Frequency (Hz)

59.94

59.94

50

50

50

25

30

50

60

60

50

60

24

Horizontal

Frequency (kHz)

15.73

31.47

15.63

31.25

37.5

45.00

28.13

33.75

27

28.13

33.75

56.25

67.5

• *Supported timing for 3D signal in Frame Sequential format.

Pixel Frequency

(MHz)

13.5

27

13.5

27

74.25

74.25

74.25

74.25

74.25

74.25

74.25

148.5

148.5

• Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.


Specifications 59

Supported timing for Video and S-Video inputs

Video mode

NTSC*

PAL

SECAM

PAL-M

PAL-N

PAL-60

NTSC4.43

Horizontal

Frequency (kHz)

15.73

15.63

15.63

15.73

15.63

15.73

15.73

Vertical Frequency

(Hz)

60

50

50

60

50

60

60

*Supported timing for 3D signal in Frame Sequential format.

Color sub-carrier

Frequency (MHz)

3.58

4.43

4.25 or 4.41

3.58

3.58

4.43

4.43

60 Specifications http://www.pureglare.com.au

Warranty and Copyright information

Limited warranty

BenQ warrants this product against any defects in material and workmanship, under normal usage and storage.

Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.

Important: The above warranty shall be void if the customer fails to operate the product in accordance with BenQ's written instructions, especially the ambient humidity must be inbetween 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920 feet, and avoiding to operate the projector in a dusty environment. This warranty gives you specific legal rights, and you may have other rights which vary from country to country.

For other information, please visit www.BenQ.com.

Copyright

Copyright 2013 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of

BenQ Corporation.

Disclaimer

BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others are copyrights of their respective companies or organizations.

Patents

This BenQ projector is covered by the following patents:

U.S. patents 6,837,608; 7,275,834; 7,181,318. TW patents 202690; 205470; I228635;

I259932.

China patents ( 中国发明专利 ) ZL01143168.7; ZL03119907.0; ZL200510051609.2

Warranty and Copyright information 61 http://www.pureglare.com.au

No results