advertisement
STAGE COLOR 48
Official version will follow soon on:
WWW.BRITEQ-LIGHTING .COM
TABLE OF CONTENTS
1. Safety Instruction
2. Technical Specification
3. How To Set The Unit
4. How To Control The Unit
5. Troubleshooting
6. Fixture Cleaning
1C
The housing, the lenses must be replaced if they are visibly damaged.
1. Safety Instruction
WARNING
Please read carefully the instruction, which includes important information about the installation, usage and maintenance.
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the unit.
Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
The unit is for indoor use only. Use only in a dry location.
The unit must be installed in a location with adequate ventilation, at least 50cm from
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer.
Installation
The unit should be mounted via its metal hole on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a 10 times weight of the unit.
2. Technical Specification adjacent surfaces. Be sure that no ventilation slots are blocked.
Disconnect main power before replacement or servicing.
Make sure there is no flammable materials close to the unit while operating as it is fire hazard.
Use safety cable when fixes this unit.
Maximum ambient temperature is TA: 40 ℃. Don’t operate it where the temperature is higher than this.
In the event of serious operating problem, stop using the unit immediately. Never try to
DMX 512 control channels: 4/7/8/11/16/19 channels switchable
Individual control of each LED cluster
Great built-in programs under Master/Slave mode triggered by music
Dimmer and Strobe adjustable
High efficiency optical system
Available in 15 degree and 25 degree
LCD display for easy addressing and setting repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
Do not touch any wire during operation as high voltage might be causing electric shock.
Voltage: AC 100-240V~50/60Hz
Power consumption: 56.6W
Light Source: total:48pcs, red: 12pcs, green: 12pcs, blue:12pcs, white/amber:12pcs
Fuse: T 6.3A
Warning
Dimension: 422 x 169 x 174 mm
Weight: 4.9 kgs
PRELIMINARY MANUAL
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
Do not open the unit within five minutes after switching off.
2C 3C
3. How To Set The Unit
3.1 Control Panel
Display
To show the various menus and the selected functions
LED
DMX
MASTER
On
On
DMX input present
Master Mode
3.2 Main Function
To select any of the given functions, press the MENU button up to when the required one is showing on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
Press ENTER button to store. Back to the main functions without any change press the
MENU button or wait for 8 seconds.
Hold MENU button to quit menu mode, the unit will run the built-in program you selected.
At this time you can press DOWN and UP button to change show, the new show will effect immediately. If you change to show 1-8 or Auto Fade, you can press ENTER button to choose speed. The unit will run in the speed that selected or it will run to the music.
SLAVE On Slave Mode
The main functions are shown on the
SOUND Flashing Sound activation drawing:
Button
DMX Address
MENU To select the programming functions
Press the MENU button up to when the DMX
DOWN To go backward in the selected functions
Address is showing on the display. Press
Mains input
Fuse
UP
ENTER
Connect to supply mains power.
Mains output
To go forward in the selected functions
To confirm the selected functions
Connect to supply mains power for other units.
ENTER button and the display will blink. Use
DOWN and UP button to change the
DMX512 address. Once the address has been selected, press the ENTER button to store. Back to the main functions without any change press the MENU button or wait for 8 seconds.
For over current protection.
Channel Mode
DMX input/output PRELIMINARY MANUAL
By connect to the 1/4’’ microphone jack to control the unit for Stand by, Function and Mode function.
Press the MENU button up to when the
Channel Mode is showing on the display.
Press ENTER button and the display will blink. Use DOWN and UP button to select the
4, 7, 8 , 11, 16 or 19 channels mode. Once selected, press the ENTER button to store.
Safety Ring
Back to the main functions without any
Keep the installation safe.
4C 5C
change press the MENU button or wait for 8 seconds.
Show Mode
Press the MENU button up to when the Show Mode is showing on the display. Press
ENTER button, the display will blink. Press DOWN and UP button to select Show 0 (Auto show), Show 1 or … or Show 8 or Auto Fade, once selected, press MENU button to store and back to the last menu, then the unit will run to music. If you choose Show 1-8 or Auto
Fade, press the ENTER button to confirm, then you can press DOWN and UP button to select Speed 1 (slow speed) or Speed 2 (middle speed) or Speed 3 (fast speed), press
ENTER button to store, the unit will run in the speed that selected. Back to the main functions without any change press the MENU button or wait for 8 seconds.
Color Mode
Press the MENU button up to when the Color Mode is showing on the display. Press
ENTER button, the display will blink. Press DOWN and UP button to select Manu (manual
Black Out
Press the MENU button up to when the Black Out is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the yes (yes blackout) or no (no blackout) mode. Once selected, press the ENTER button to store. Back to the main functions without any change press the MENU button or wait for 8 seconds.
Back Light
Press the MENU button up to when the Back Light is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the on (back light on) or off (back light off 1 minute after auto show) mode. Once selected, press the
ENTER button to store. Back to the main functions without any change press the MENU button or wait for 8 seconds.
Auto Test
Press the MENU button up to when the Auto Test is showing on the display. Pressing setting), Color 1 or … or Color 32, once selected, press MENU button to store. If you choose Maun, press the ENTER button to confirm, you can press DOWN and UP button to
ENTER button and the display will show Test… and the unit will run self-test by built-in program. To go back to the functions press the MENU button.
Manual Test select Red or Green or Blue or White/Amber, press ENTER button to confirm and press
DOWN and UP button to adjust the value, then press ENTER button to store. Back to the main functions without any change press the MENU button or wait for 8 seconds.
Slave Mode
Press the MENU button up to when the Manual Test is showing on the display. Press
ENTER button and Red 1 will blink, use DOWN and UP button to choose Green 1 or Blue 1
Press the MENU button up to when the Slave Mode is showing on the display. Press
ENTER button and the display will blink. Use DOWN and UP button to select the slave 1 or slave 2 mode. Once selected, press the ENTER button to store. Back to the main functions without any change press the MENU button or wait for 8 seconds.
Sound State or White/Amber 1 or Red2 or … or White/Amber 4 or Dimmer or Strobe, press ENTER button to enter, then press DOWN and UP button to adjust the value and press ENTER button to choose next optional. Back to the main functions without any change please press the MENU button.
White Balance
Press the MENU button up to when the White Balance is showing on the display. Press
ENTER button and the r 255 will blink, press DOWN and UP button to adjust the value, Press the MENU button up to when the Sound State is showing on the display. Press press ENTER button to store and g 255 will blink on the display, press DOWN and UP ENTER button and the display will blink. Use DOWN and UP button to select the on (sound button to adjust the value, press ENTER button to store and b 255 will blink on the display, control on) or off (sound control off) mode. Once selected, press the ENTER button to store.
Back to the main functions without any change press the MENU button or wait for 8 seconds.
Sound Sense
PRELIMINARY MANUAL
ENTER button and the display will blink. Use DOWN and UP button to adjust the sound sensitively (1-100) of the unit. Once the value has been selected, press the ENTER button press DOWN and UP button to adjust the value, and press ENTER button to store. Back to the main functions without any change please press the MENU button.
Fan Speed
Press the MENU button up to when the Fan Speed is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select Auto Speed
(When the temperature of the unit under 40 ℃, FAN stops; between 45℃~55℃, FAN runs at to store. Back to the main functions without any change press the MENU button or wait for 8 half speed; above 60
℃, FAN runs at full speed. The LEDs will be off if the temperature seconds.
6C 7C
higher than 75 ℃)or High Speed, press ENTER button to store. To go back to the functions press the MENU button.
Fixture Temp
4.2 Easy Controller
The easy remote control is used only in master/slave mode. By connecting
Press the MENU button up to when the Fixture Temp is blinking on the display. Pressing
ENTER button and the display will show the temperature of the unit. To go back to the functions press the MENU button.
Fixture Time to the 1/4” microphone jack of the first unit, you will find that the remote controller on the first unit will control all the other units for Stand by,
Function and Mode selection.
Stand By Blackout the unit
Press the MENU button up to when the Fixture Time is blinking on the display. Pressing
ENTER button and the display will show the number of working hours of the unit. To go back to the functions press the MENU button.
Firmware Version
Function 1. Sync. Strobe
2. Async strobe
3. Sound Strobe
Select
Manual Color or Color 1-32
Select show
1-8 or Auto fade
Select Speed
1. Fast
2. Middle
3.Slow
Press the MENU button up to when the Firmware Version is blinking on the display.
Pressing ENTER button and the display will show the version of software of the unit. To go back to the functions press the MENU button.
Mode Sound (LED OFF) LED On Slow blinking Fast blinking
4.3 DMX Controller
Use universal DMX controller to control the units, you have to set DMX address from 1 to
4. How To Control The Unit
You can operate the unit in three ways:
512 channel so that the units can receive DMX signal.
Press the MENU button up to when the DMX Address is showing on the display. Press
1. By master/slave built-in preprogram function
2. By easy controller
3. By universal DMX controller
ENTER button and the display will blink. Use DOWN and UP button to change the DMX512 address. Once the address has been selected, press and keep ENTER button to store when.
To go back to the functions without any change press the MENU button or wait for 8 seconds.
4.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other units to
Please refer to the following diagram to address your DMX512 channel for the first 4 units: give an automatic, sound activated, synchronized light show. This function is good when you want an instant show.
Channel Mode Unit 1 Unit 2 Unit 3 Unit 4
2-light show
4 channels 1 5 9 13
In slave mode, slave 1 means the unit run as the master unit and slave 2 means 2-light show.
7 channels 1 8 15 22
In order to create a great light show, you can set slave 2 on the second unit to get contrast movement to each other, even if you have two units only.
8 channels
11 channels
16 channels
1
1
1
9
12
17
17
23
33
25
34
49
19 channels 1 20 39 58
8C 9C
4.4 DMX 512 Configuration
PRELIMINARY MANUAL
10C 11C
4.5 DMX512 Connection
1.
If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable.
2.
At last unit, the DMX cable has to be terminated with a terminator. Solder a
120 ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin
XLR-plug and plug it in the DMX-output of the last unit.
3.
Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system.
4.
The DMX output and input connectors are pass-through to maintain the DMX circuit, when power is disconnected to the unit.
5.
Each lighting unit needs to have an address set to receive the data sent by the controller. The address number is between 0-511 (usually 0 & 1 are equal to
1).
6.
The end of the DMX 512 system should be terminated to reduce signal errors.
PRELIMINARY MANUAL
Pin 4/5: Not used.
12C 13C
5. Troubleshooting
Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling.
2. Check the LED for the response of the master/ slave mode signal.
D. No response to the sound
1. Make sure the unit does not receive DMX signal.
2. Check if the sound sensitively is too low.
1. The cable connected to the PCB may broken.
14C
6. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
EC - Declaration of Conformity
We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive
89/336/EEC.
EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL: 2000+A12: 2002
Safety of household and similar electrical appliances
Part 1: General requirements
15C
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project