advertisement
ORX 1-00
CATV Optical Receiver
Operation instructions
Operation Instructions | ORX 1-00 | CATV Optical Receiver
Table of contents
2 2017-10-24 | Technical improvements, changes in design, printing- and other errors expected.
Safety instructions
∂ ORX 1-00 is indoor design without waterproof function.
If it works outdoor that should be put into a waterproof and moisture-proof cabinet.
∂ Installation MUST be operated by trained or professional person.
Direct eye exposure to laser beam may cause physical damage
2017-10-24 | Technical improvements, changes in design, printing- and other errors expected.
3
Operation Instructions | ORX 1-00 | CATV Optical Receiver
1. Description
ORX 1-00 CATV optical receiver, compacted in size, designed for FTTH (Fiber To The Home) networks. ORX 1-
00 works under 1100~1650nm. ORX 1-00 is the new type micro optical receiver with LED optical power indicator.
1.1.
Delivery
Description
Optical Receiver Unit
External Power Supply Adapter 1
User’s Manual 1
Quantity
1
1.2.
Features
∂ Compacted in size with nice appearance
∂ AGC (Auto Gain Control) function
∂ Low power consumption <3W
∂ 0~10dB adjustable attenuator
∂ Low noise and high sensitive PIN Diode
∂ External power supply adapter
∂ Cost effective with high performance
1.3.
Applications
∂ CATV, HFC networks
∂ FTTH, FTTB networks
∂ PON RF Overlay
1.4.
Block Diagram
4 2017-10-24 | Technical improvements, changes in design, printing- and other errors expected.
‚ ƒ
„
…
†
†
•
Outlines Drawing (dimensions are in mm)
3
4
5
6
No
1
2
…
Description
Optical Input Port: optical input connecter insert here
Optical Power Indicator: Green (Normal); Red (Strong); No Light (Weak/No power)
Power ON/OFF Indicator:
0~10dB Adjustable Attenuator: Counter-clockwise increases value
RF Output Port: RF signal output to TV
Power Jacket: 9VDC or 12VDC
2017-10-24 | Technical improvements, changes in design, printing- and other errors expected.
5
Operation Instructions | ORX 1-00 | CATV Optical Receiver
2. Installation
Caution
∂ 1.ORX 1-00 is indoor design without waterproof function.
If it works outdoor that should be put into a waterproof and moisture-proof cabinet
∂ 2. Power supply is required as 100-240VAC with lightning protection
∂ 3.Installation MUST be operated by trained or professional person.
Insert the AC power cord into the power jack, and connect to power socket
Connect to power jack
When get through the power supply, the power supply indicator turns ON in RED
Connect coaxial cable to RF Output Port
Power Supply Indicator
F5 cable connector to
RF output port
6 2017-10-24 | Technical improvements, changes in design, printing- and other errors expected.
Clean the fiber cable connector and ends with cleaning tools Do not scratch the fiber connector or ends.
Wipe the surface with alcohol with a dust-free cloth. Next, wipe it with a dry dust free cloth, and then quickly wave the fiber end back and forth in the air. Do not blow air onto the fiber to dry it.
Direct eye exposure to laser beam may cause physical damage
Well connect fiber optical connector to optical receiver’s optical input port
Insert here
Verify input optical power indicator in 3 status
Status
Green Color
Red Color
Light OFF
Description optical power indicator input power is under working range input power is strong
Input power is weak or no input power
Check RF output level by FSM,adjust Attenuator(E) to get the required output level
Adjustable Attenuator
Operation
Increase Value
Description
Rotate counter-clockwise 0~10dB
Decrease Value Rotate clockwise 0~10dB
Mounted on the wall or enclosure.
2017-10-24 | Technical improvements, changes in design, printing- and other errors expected.
7
Operation Instructions | ORX 1-00 | CATV Optical Receiver
3. Troubleshooting
Status
Power supply LED indicator is OFF
Input optical signal is poor
Output level is low
Possible Method to slove
Check the power cord plug is well connected
Check the power jack on receiver is firmed well
Check input power according to 3-stage input power indicator or measure the input power
Check optical connector: SC/UPC or SC/APC is corrected
Clean the optical connector’ surface
Verify the input optical signal is normal
Check the Adjustable Attenuator is correct, rotate it to get the required output level
Check optical transmitter work normally
8 2017-10-24 | Technical improvements, changes in design, printing- and other errors expected.
4. Specification
4.1.1.
Optical Characteristics
Parameter
Wavelength
Input Level Range (PIN)
AGC Range
Optical Return Loss
Connector Type
Unit nm dBm dBm dB
--
4.1.2.
RF Characteristics
Parameter
Frequency Range
Gain Flatness
Output Level
CTB1
CSO1
C/N1
Unit
MHz dB dBµV dB dB dB
Value
1100-1650
-12~ -1
-10~ -3
≥45
FC/APC or SC/APC
Value
47~1002
±0.75
80±1
≥63
≥63
≥51
2017-10-24 | Technical improvements, changes in design, printing- and other errors expected.
9
Operation Instructions | ORX 1-00 | CATV Optical Receiver
10 2015-11-29 | © AXING AG Swizzerland | Technical data are subject to change, errors and omissions excepted
advertisement
Related manuals
advertisement