Full HD IP Box Camera

CamPilot STH120

User Manual

Overview

CamPilot STH120

(Lens are sold separately)

Accessories

Before installing and using the product, please read this manual carefully.

Be sure to keep it handy for later reference.

• 1/3" Panasonic CMOS

• True Day & Night / 3D DNR / WDR / BLC / DEFOG

• C/CS Mount, DC Iris Lens Support

• 1920x1080 resolution at 30FPS

• Multi-codec support : H.264 / MJPEG / MPEG-4

• Multi-stream with variable resolution & frame

1st stream : H.264 or MJPEG @ 1080p~VGA

2nd stream : H.264, MPEG4 or MJPEG @ D1~CIF

3rd stream : H.264, MPEG4 or MJPEG @

CIF~QCIF

• Stream based motion detection

• Multi-codec audio support : G.711 / G.726

• Two-way audio supported (Full Duplex)

• Alarm Input (1ch) / Output (1ch)

• SD / SDHC card support

• Power : DC 12V, 1A (PoE)

An adaptor and a LAN cable are not included in the product

1

Precaution

WARNING

TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTIONS

■ Do not open or modify

Do not open the case, as it may be dangerous and cause damages.

■ Do not put objects inside the unit

Make sure that no metal objects or flammable substances get inside the camera. It could cause fire, short-circuits or damages.

■ Be careful when handling the unit.

To prevent damage, do not drop the camera or subject it to strong shock or vibration.

■ Install away from electric or magnetic fields.

■ Protect from humidity, dust and high temperature.

An additional case that is temperature-controllable, damp-proof and waterproof is required for outdoor use.

■ Cleaning

Dirt can be removed from the case only by wiping it with a soft cloth moistened with a soft detergent solution.

■ Mounting Surface

The mounting surface material must be strong enough to support the camera.

■ CamPilot STH120 can be used for surveillance purpose.

Be thoroughly informed of related regulations prior to installation to ensure compliance with such regulations

2

Overview

Features and Appearance

CamPilot STH120 is an IP Camera that transmits real-time high-resolution digital video and audio data with H.264 high compression rate over Internet or Intranet.

▶ Front

C/CS mount ring

▶ Rear (detail)

DC Iris connector ▶ Side

▶ Top

DC12V (Power, No polarity)

LAN / POE (Network)

VIDEO (D1 output for test, BNC connector)

RESET (Setting initialization switch)

AUDIO IN / OUT

RS422 (Pan/Tilt communication,

TX: transmission, RX: reception)

DIO (Digital Input / Digital Output)

3

Specification

Camera Module

Items

Device

Pixels

Min. Illumination

Resolutions

Shutter Speed

Video Compression

Audio Streaming

External I/O

Netw ork

Function

Privacy Zone

S/N Ratio

Compression Type

Resolutions

Bitrate

Frame Rate

Streaming

Bi-Directional Audio

Audio Compression

Audio Line Input

Audio Line Output

Alarm Input / Output

RS422 (RS485)

Local Storage

Reset Button

Ethernet

Protocol

Softw are OS

Web Brow ser

SDK

Security

Operating

Pow er

Physical

Case

Temperature

Pow er Requirement

Weight

Material

* All specif ications are subject to change without notice.

Specification

1/3" Panasonic CMOS

1944(H) x 1092(V) = 2,122,848 (pixel) (Effective)

Color : 1.0 lux / BW : 0.5lux / Color DSS : 0.002 lux / BW DSS : 0.001 lux

Digital ; 1920x1080p(1080p/30fps) , 1280x720p(720p/60fps)

Auto / Manual ( 1/30(1/25) ~ 1/60000 )

AGC, WDR/BLC Mode, DAY&NIGHT (Auto / Day / Night / Ext),

SMART IR, WHITE BAL (Auto / Manual / etc.), 2D/3D DNR, DEFOG

Off / On (32 points) more than 50dB (AGC off)

H.264(MPEG4 AVC) @L3.0 / MJPEG / MPEG4

1080p / 720p / D1 / 4CIF / VGA / CIF / QVGA / QCIF

32Kbps ~ 6Mbps

30FPS @1920x1080p

H.264 Triple Stream or Simultaneous H.264 / MPEG4 / MJPEG

Tw o w ay, full duplex

G.711 / G.726

Line level input. Nominal 0-dB input level is 1.0 VRMS.

Line level output. Nominal output level 1.0 VRMS.

1 ch / 1ch

1Ch. for External Device Control like a Serial Device

Micro SD / SDHC Card support up to 32 GB

Restore to default setting (Netw ork, Passw ord and etc)

Ethernet(10/100 Based-T), RJ-45 Connector

TCP, IP, HTTP, DHCP, FTP, DNS, DDNS, NTP, ICMP,

SNMP, SMTPE, UPnP, RTP, RTSP, Onvif

Embedded OS (Linux)

IE 8.0 or above

Cellinx SDK 4.0

MD5 Passw ord / iptables (firew all) / SSL

-10°C ~ 55°C / 14°F ~ 131°F

DC 12V 1A / PoE (IEEE802.3af)

1.5 kg

Aluminum (IP66)

4

Dimension

▶

Front

▶

Side

REF Monitoring PC Requirements

Item

Processor

Specification

Pentium Core2 Duo or more

Monitoring

PC

RAM

Graphic Card

OS

Monitor Resolution

Network

2GB or more

512MB or more

Windows 2003 / XP / Vista / 7

1024 X 768 pixels or more

10/100 Base-T LAN

Specification

▶

Top

▶

Rear

5

Connection

Basic connection

(1) DC 12V

– power, DC 12V 1A adaptor (

No polarity , auto switching)

(When the PoE is used, the power connection is not necessary.)

(2) LAN / POE – ETHERNET, LAN cable (RJ45 jack, Auto detection of cross/direct cable)

(Please, refer to the standard of “IEEE 802.3af”)

Expert connection

(1) AUDIO IN / OUT

- IN: microphone, line level input (RCA jack, an amplified microphone should be used.)

- OUT: speaker, line level output (RCA jack, 8Ω)

(2) RS422: external device control (etc. PTZ receiver)

(3) DI (Digital Input): sensor, no polarity (N.O / N.C are all available.)

(4) DO (Digital Output): alarm, relay switch (nominal voltage 5VDC, 1A)

An example of the relay d evice that is connected on “DO (Digital Output)”

▶

Relay device

Manufacturer: SUNWOO /

Model: SW LY2N

Fix the mount ring with the wrench after assembling the lens

▶

The hole for fixing the mount ring

IP address setup

Set the IP address (Refer to “Network” at p.7~8)

6

Network

Setting an IP address

Change the network setting value with the program “NVTManagement”

1. NVTManagement execution

• Execute the file “NVTManagement.exe”

2. IP address set-up

• Click the button “ NVT Scan ”, select the model.

• Input the IP address, Subnet Mask, Gateway and DNS Server IP address , click the button

“ Apply ”

• If you don’t have a proper IP address, ask the network administrator.

7

< 초기 접속화면 >

< 영상 모니터링>

Network

3. Accessing to CamPilot STH120 with a web browser

Open a web browser on a monitoring PC and enter the IP address assigned to a CamPilot

STH120 as following

Example> http://192.168.1.2

• The page as below shows up after the connection is completed.

ID / Password : root / pass (Initial Value)

Login button : it enables you to move to the Web

Monitoring Page. On checking the

Setting box and clicking the button, you

▶

The Initial Page

▶

Web Monitoring Page

Refer to the document “STH120_Web_Manual.pdf” for the Web server. can move to the Web Setting Page.

Guest Login : you can move to the Web Monitoring

Page as “guest”

8