ConTech Lighting CY3 SC 3-1/2 Inch Round Integrated LED Surface Mount Cylinder Instruction Sheet

INSTALLATION INSTRUCTIONS

|

CY3 Series 3-1/2 In. Indoor Round Cylinders:

Surface Mount with Conduit Feed Box

The important safeguards and instructions in this manual are not meant to cover all possible conditions and situations that may occur.

Note: Before attempting installation, please refer to your local electrical code.

IMPORTANT SAFETY INSTRUCTIONS:

• Read all the instructions before installation. SAVE THESE

INSTRUCTIONS FOR LATER USE.

• Product should be installed by a Qualified Electrician.

• All electrical connections must be in accordance with local and

National Electrical Code (NEC) standards. If you are unfamiliar with proper electrical wiring connections, obtain the services of a qualified electrician.

• Before starting the installation, make sure all electricity has been turned off and electrical breaker has been locked out and tagged out. Turning the power off at the light switch is not sufficient to prevent electrical shock.

• Product must be grounded to avoid potential electric shock and any other potential hazards.

• Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in compliance with

National Electrical Code and local codes. Use of accessory equipment is not recommended.

• Do not mount near gas or electric heaters.

• Equipment should be mounted in locations and at heights where it will not readily be subject to tampering by unauthorized personnel.

• WARNING: RISK OF SHOCK

− Turn off the power at fuse or circuit breaker box before installation or maintenance work.

− Wear rubber soled shoes and work on a sturdy wooden or non-conductive ladder.

− Ground the fixture to avoid potential electric shocks and to ensure reliable starting.

− Double check all connections, making sure they are tight and correct.

• WARNING: RISK OF FIRE

− Most dwellings built before 1985 have supply wire rated at 60°C

− Supply conductors (power wires) connecting the fixture must be rated at minimum of 90°C

− Consult a qualified electrician before installation

• Installing contrary to instructions may cause unsafe conditions.

• If the product has any visible damage do not install it.

• To avoid hazards to children, account for all parts and properly dispose of all packing materials.

• Call the Technical Support department at ConTech Lighting with any installation questions: 847.559.5500.

INSTALLATION

FIGURE 1

• Remove Twist-and-Lock Adapter Plate for ease of installation.

Note orientation of Plate before removal.

• Install the Conduit Feed Box in desired location; hardware not provided.

FIGURE 3

• Ensure 3/4 inch EMT Conduit is completely deburred and insert into desired entry points. EMT Conduit should be fully seated against built in Stop Block.

• Tighten Outer Conduit Strap Screws, alternating to maintain even pressure.

• Tighten Center Set Screw to fully secure Conduit.

Twist-and-Lock

Adapter Plate

Stop Block

EMT Conduit

FIGURE 2

• Loosen Conduit Strap Screws to remove Knockout Plug for desired entry points.

Conduit Strap Screws

Tether

Outer Conduit

Strap Screw

Center Conduit

Strap Screw

Knockout Plug

CONTINUED

CONTECH LIGHTING | 725 LANDWEHR ROAD | NORTHBROOK, ILLINOIS 60062 | PHONE 847.559.5500 | www.contechlighting.com

©2022 Conservation Technology of Illinois, LLC. All rights reserved. Note: Specifications subject to change without notice.

CY3 CMSC INST REV0622

All specifications subject to change without notice. For ConTech’s limited product warranty, go to www.contechlighting.com. For a printed copy of the warranty, call 1-847-559-5500.

P1

INSTALLATION INSTRUCTIONS

|

CY3 Series 3-1/2 In. Indoor Round Cylinders:

Surface Mount with Conduit Feed Box

The important safeguards and instructions in this manual are not meant to cover all possible conditions and situations that may occur.

Note: Before attempting installation, please refer to your local electrical code.

INSTALLATION CONTINUED

FIGURE 4

• Re-install Twist-and-Lock Adapter Plate with Retention Springs located on the INSIDE of the Conduit Feed Box.

FIGURE 6

• Reattach Cylinder to Conduit Feed Box by twisting into the fully seated position and tightening the Set Screw on the Conduit

Feed Box.

Set

Screw

FIGURE 5

• Clip Cylinder Tether to Conduit Feed Box Tether to assist in wiring.

• Attach Black Line/Hot Wire to Black Wire, White/Neutral Wire to

White Wire and Green/Ground Wire to Green Wire with Wire Nuts

FOR 0-10V DIMMING:

Attach Purple Wire of LED Driver to DIM (+) with Wire Nut and

Pink/Gray Wire of LED Driver to DIM (–) with Wire Nuts. If not dimming, use wire connectors to cap these wires individually.

• Carefully feed any excess wire into Conduit Feed Box to avoid pinching wires.

Electrical Connections:

• Green/Ground

• White/Neutral

• Black (Line)/Hot

0-10V Dimming Wires:

• Purple/Positive (+)

• Pink or Gray/Negative (–)

CONTECH LIGHTING | 725 LANDWEHR ROAD | NORTHBROOK, ILLINOIS 60062 | PHONE 847.559.5500 | www.contechlighting.com

©2022 Conservation Technology of Illinois, LLC. All rights reserved. Note: Specifications subject to change without notice.

CY3 CMSC INST REV0622

All specifications subject to change without notice. For ConTech’s limited product warranty, go to www.contechlighting.com. For a printed copy of the warranty, call 1-847-559-5500.

P2