User manual V1.1

MIO MVS-4HDMI Quad Multi-viewer system
User manual V1.1
Gefei Tech Co.,Ltd
Copyright
Copyright © 2009 Beijing Gefei Tech. Co., Ltd all rights reserved. This document may not
be copied in whole or in part.
Trademarks
Gefei-Tech，Magi，MIO，VIO，XIO，MVS，MRS are either registered trademarks or
trademarks of Beijing Gefei Tech. Co., Ltd in China and/or other countries. Other
trademarks used in this document are either registered trademarks or trademarks of the
manufacturers or vendors of the associated products.
Disclaimer
Product options and specifications subject can be changed without notice. The
information in this manual is furnished for informational use only, is subject to change
without notice, and should not be construed as a commitment by Beijing Gefei Tech. Co.,
Ltd .Beijing Gefei Tech. Co., Ltd assumes no responsibility or liability for any errors or
inaccuracies that may appear in this publication.
Revision Status
Rev Date
Description
Aug 8, 2013
release of the MIO MVS-4HDMI User Manual
WEB Software V1.1
Content
1. Description ................................................................................................................................. 1
2. Features ..................................................................................................................................... 1
3. Special Notice ............................................................................................................................ 2
4. Panel Description ...................................................................................................................... 3
4.1 Buttons Definitionl ............................................................................................................... 3
4.2 Right Panel ........................................................................................................................... 3
4.3 Left panel ............................................................................................................................. 5
5. How to Use the Remote Control Software ............................................................................ 5
5.1 Attention before Use ........................................................................................................... 5
5.2 Basic Physical Configuration ................................................................................................ 5
5.2.1 Edit Input Source ...................................................................................................... 6
5.2.2 Rotate Screen............................................................................................................ 7
5.3 General Configuration ......................................................................................................... 7
5.3.1 Function Overview .................................................................................................... 7
5.3.2 System Settings ........................................................................................................ 8
5.3.2.1
Choose Input Source ......................................................................................... 10
5.3.2.2
Make/Delete Signal Marker .............................................................................. 11
5.3.2.3
Create Clock/Timer/Logo .................................................................................. 11
5.3.2.4
Delete an Object ............................................................................................... 12
5.3.2.5
Clear All ............................................................................................................. 13
5.3.2.6
Scree ................................................................................................................. 13
5.3.2.7
Quick Tools ........................................................................................................ 13
Do & Undo ............................................................................................................. 13
Alignment tools ..................................................................................................... 13
Full Screen ............................................................................................................ 14
5.3.2.8
Layout Management ......................................................................................... 14
Save Layout .......................................................................................................... 14
Edit Layout ............................................................................................................ 14
Delete Layout ........................................................................................................ 15
Download Layout File .......................................................................................... 15
Upload Layout File ............................................................................................... 15
5.3.2.9
HDMI Output Resolution................................................................................... 15
5.3.2.10 Audio Output Settings....................................................................................... 16
5.3.2.11 Ratio of Video ................................................................................................... 16
5.3.2.12 Ratio of Channel................................................................................................ 16
5.3.2.13 UMD & Audio Meters Display ........................................................................... 16
5.3.2.14 Attach to point .................................................................................................. 17
5.3.2.15 Position and Size ............................................................................................... 18
5.3.2.16 Set Air Timer ..................................................................................................... 18
5.3.2.17 OSD Elements.................................................................................................... 18
UMD Settings ........................................................................................................ 19
Tally Settings ......................................................................................................... 19
Adjustment the transparency of Audio and UMD ............................................ 20
Display settings .................................................................................................... 21
Adjust Border Color.............................................................................................. 21
5.3.2.18 Extended Settings ............................................................................................. 22
Set Color Parameters .......................................................................................... 22
Series Ports Settings ........................................................................................... 22
Timing Settings ..................................................................................................... 23
Upload Custom Picture ....................................................................................... 23
5.3.2.19 Save ................................................................................................................... 23
5.3.3 Detection Settings .............................................................................................................. 24
5.3.3.1
Audio Detection ................................................................................................ 25
Audio Overload ..................................................................................................... 25
Audio in Silence .................................................................................................... 26
5.3.3.2
Video Detection ................................................................................................ 26
Loss of Signal ....................................................................................................... 26
Video Frozen ......................................................................................................... 26
Video Black ........................................................................................................... 26
5.3.4 User Configuration.......................................................................................................... 26
5.3.5 Network Configuration ................................................................................................... 27
5.3.6
Help................................................................................................................................. 28
Contact Us ..................................................................................................................................... 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
1. Description
Based on Mini BOX platform, MIO MVS-4HDMI is a high-quality four viewers display system. It
supports 4 channels HDMI signal input, provides the HDMI double output, HDMI output can reach
1920 x1080p.
MIO MVS-4HDMI is conveniently and flexibly set to monitor the project , such as display input
resolution, AFD information, safety frame. it supports multiple resolution output, provide video and
audio detection and alarm, such as black Field, frozen and audio overweight, It supports SNMP. It can
be real-time managed and monitored by NETwork, via Ethernet.
MIO MVS-4HDMI widely used in the studio, video conference center, broadcast prison see room,
outside, multimedia dispatching command center and so on the many kinds of applications
2. Features

Compatible with a variety of formats signal adaptive input.

Support HDMI output system.
 Support the same input signal displaying in different video channels
 Provide build-in web server to control whole system via RJ45 interface
 Audio signals from input source are selectable to be embedded into HDMI or HDSDI output signal
on the web control page
 Flexible output options：4:3, 16:9, customized aspect ratio
 Editable one program UMD and up to 8 channel audio meters display
 Provides several kinds of timer: air timer and countdown timers, analog and digital clocks types
 Mark key signal/signals to find it/them rapidly in one complicated layout
 Support user-define the border color of each channel separately or cancel border display
 Support format display of input signal and AFD information display
 Video/audio auto detection and alarming, such as video loss, video frozen, video black, audio
silence, audio overload with high rate of accuracy
 Two forms of alarm: text alarm and icon alarm
 Support customized layout to preset various layouts for different application, such as studio, OB
van, production room and so on
Gefei Tech. Co., Ltd
1 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
3. Special Notice
1. In order to avoid network traffic congestion, please do not submit parameters before the last
modification is applied.
2. In order to avoid hardware loose contact caused by continuous operations on the front panel,
please do your second operation after you have gotten the first operation result.
3. Generally, it will spend about three seconds to get the results after you submit. The time is related
with the monitor type. If the time is too long (over 7seconds), maybe there is something abnormal
with the hardware‟s working status (overheating for example), please wait patiently.
4. Do not plug the HDMI connector without power-down.
5. Without the professional technological guidance from our company, users are not permitted to
re-plug the modules away from the chassis or debug the internal operation .We do not undertake
any obligation or responsibility of intentional destroy to the machine.
6. Build-in Web server to control MIO MVS-4HDMI easily by your computer via Ethernet. Please make
sure IP address of MIO MVS-4HDMI is in the same network segment as your computer. And the IP
and Mac address of MVS are unique value in Ethernet.
7. Windows 2003, Windows XP, Windows Vista and Windows 7 are strongly recommended with
Internet Explorer.exe.
8. User can also upgrade system under the label “Network”. Before the upgrade, the anti-virus
software and firewall have to be closed to make sure that the upgrade data is transmitted to
Multi-viewer system without rejection. Power and network cannot be cut off during upgrading.
9. Please set all channels to input inner test signal without waveform display before upgrade. So it will
take less time to upgrade the system.
10. If the current output resolution of HDMI signal is not compatible with your monitor, you can
change the output resolution on the web control server.
Gefei Tech. Co., Ltd
2 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
4. Panel Description
4.1Buttons Definition
Template/Default: Key press and release 2 ~ 3s. You can call up the template. Key press and
release 10~ 12s . The parameters on the web page will be restored to default ones,
including IP address and user password. The default IP address is 192.168.1.76, and
default password is 000000 (six zeros).
Restart: Using a push pin to press the button, the Mini box is restarted. The function of the button
equals to turn off, and then turn on the Mini box.
4.2Right Panel
DC IN: Standard power, 12V, 1A
HDMI/DVI-OUT: Via DVI-I interface (female) to output DVI-D and HDMI signal. Although the device
adopts DVI output interface, the HDMI signal can be obtained by using a DVI to HDMI adapter or cable.
Gefei Tech. Co., Ltd
3 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
In HDMI mode, the SDI audio signals are embedded into HDMI signal.
The output resolution can be configured as below.
1024x768x60p, 1280x720x50p/60p
1280x800x60p, 1280x1024x60p
1360x768x60p, 1400x1050x60p
1600x900x60p, 1680x1050x60p,
1920x1080x50i/60i, 1920x1080x50p/60p,
Network: RJ45 interface with 10/100/1000M auto-detection. And the default IP address is
192.168.1.76. and default password is 000000 (six zeros),The web server is remote control
interface.
GPI/RS232: Serial port.
RS232, DB15 definition;
Definition
Pin
Definition
Pin
15
GND
6
CH2_TALLY
14
GND
7
CH3_TALLY
13
GND
8
CH4_TALLY
12
GND
9
TX
3
GND
10
1
Do‟not connect
5
2
Do‟not connect
11
CH1_TALLY
Do„not connect
Do„not connect
Do‟not connect
Gefei Tech. Co., Ltd
4
4 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
4.3Left panel
PWR：Power indicator, the indicator shows green as the power is working normally.
HDMI IN1 & HDMI IN2 & HDMI IN3 & HDMI IN4: Cable with HDMI interface. Support various
resolutions.
720p 50Hz/59.94Hz/60Hz
1080i 50Hz/59.94Hz /60Hz
1080p 50Hz/59.94Hz /60Hz
IN1 & IN2 & IN3 & IN4: Signal indicator, the indicator shows green as the video is locked with no
errors. Correspondence between: IN1→HDMI IN1，IN2→HDMI IN2，IN3→HDMI IN3，IN4→HDMI IN4
5. How to Use the Remote Control Software
5.1Attention before Use
Multi-viewer system has a built-in WEBSERVER, so user can configure it by Internet Explorer easily
and quickly when connecting RJ45 interface of MVS with one straight-through cable.
First step: you need to login 192.168.1.76/config.html to open physical configuration of MIO
MVS-4HDMI, such as editing the names of input sources and setting the position for screens.
Second step: Login 192.168.1.76 to open general web control of MIO MVS-4HDMI. There are several
web labels, which are System, Alarm, User, Network, and Help.
The default IP address: 192.168.1.76.
The default user name: admin
The default password: 000000
5.2Basic Physical Configuration
Open IE browser on Client PC, and input “http://192.168.1.76/config.html” in location bar to open
web page of Physical Configuration. The page is shown as below.
Gefei Tech. Co., Ltd
5 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
5.2.1 Edit Input Source
Edit name of input source for each input card on the left of web page.
Double click each bar to edit individual name
for each input source
The table of relationship between input source and inserted slots：
The signal name of A1 is the one inputted via HDMI IN1 interface, and so does A2, A3 and A4.
Gefei Tech. Co., Ltd
Interface
Source Name on Web page
HDMI IN1
A1
HDMI IN2
A2
HDMI IN3
A3
HDMI IN4
A4
6 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
5.2.2 Rotate Screen
Display
IP
address
Return
to
System
Display
Area
Display IP address: Show the IP address of quad-viewer output system, read only.
Return to System: To release current name of input sources and arrangement of screens and jump
to web page of 192.168.1.76
5.3General Configuration
You do not need to install the client software. Open the IE Browser, and input the IP address in the
location bar to open the user interface. Default IP address is: http://192.168.1.76.
Here appears a dialogue box for user login. Please input user name and initial password. Then click
“login”, you will enter into the actual control interface.
User name: admin;
Password: 000000.
5.3.1 Function Overview
Gefei Tech. Co., Ltd
7 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
There are several labels at the top of the web page: System, Alarm, User, Network, and Help.
System: To design the output display layout via creating or deleting windows, clock, Logo, UMD and
other display elements.
Alarm: The system supplies audio and video detection, such as audio overload, audio silence, video
frozen, video black, and signal loss. Each alarm threshold can set to meet your needs.
User: The system supports user name called admin. The initial password is 000000 which can be
changed, and new password will take effect when user logs in next time.
Network: To modify the IP address and upgrade the firmware. The modification will take effect after
restart the machine.
Helps: To show the versions of each firmware here.
5.3.2 System Settings
You can accomplish the basic configuration in the System Settings, which includes the following
functions: to create or delete the channels, to add the clock and logo, to align selected channels via
the quick tools, to undo the previous operations, and to set the parameters, such as output resolutions,
aspect ratio, extended configuration and so on.
The descriptions are in detail as follows.
Label area
Operation area for
channels and other display
elements of each
Choose
language
The list of
input sources
Parameters
setting area
Make/Delete
signal marker
Layout
management
Quick tool for
alignment
Create a Channel
According to the settings on web page of Physical Configuration, system detects the name of input
source for each input card and makes a list of them.
Gefei Tech. Co., Ltd
8 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
Click pink button to create
channel A1, A2, A3, and A4
A1~A4, the signals accessed
via HDMI IN1~ IN4 interface
Steps to create a certain video channel:
Step 1-Click the needed channel in the
list of signal sources. For example, if the
needed channel is A4, click the bar of
“Router3”, which turns blue.
Step 2-Click pink button
Step 3-Hold the mouse and drag
a frame from top to bottom on
the target screen.
Gefei Tech. Co., Ltd
9 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
Step 4-Release the mouse. System
creates a channel A4 as the size and
position of the frame. You can change
the size and position of the channel
freely afterwards.
Note: If skip step 1 and operate by step 2 directly, then the channels will be created in the order of
number 1 to number 4.
Channel A4 is created as below.
Channel ID
Name of current source
For each virtual channel, it shows three details.
1， Channel ID. Each channel has exclusive Channel ID;
2， Name of input source displaying in this channel currently, for example, “Router3”;
5.3.2.1 Choose Input Source
Sources accessed via HDMI IN1~IN4, which can be
displayed freely in channel A1, A2, A3, and A4.
Steps to appoint input source to video channel
Step 1-Use the mouse to choose a needed input source in the list, and drag it out,
Step 2-Drag the signal out of the list until it located on the target channel, and then release the
mouse.
Gefei Tech. Co., Ltd
10 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
5.3.2.2 Make/Delete Signal Marker
Key signal can be marked with red font. Meanwhile, the channel whose current source is key signal will
be marked with red border, in order to locate it quickly in a complicated layout, even after a series of
position adjustment.
Name of key source is marked with
red font in the list. And the channel
which
uses
this signal
as the
current display source appears red
border, not only on the web, but on
the actual output as well. You can
remove the signal marker by using
“Delete Marker” button.
Note: 1. Multiple signals can be marked at same times.
2. On actual output, the channel which uses the signal as the current display source appears red
border.
5.3.2.3 Create Clock/Timer/Logo
The following objects can be created besides video channels.
Analog Clock, Digital Timer, Count-down Timer, Air Timer, and Logo
You can create one of Analog Clock/ Digital Timer/ Count-down Timer/ Air Timer/ Logo on the screen.
The size of Logo and Analog Clock cannot be changed. You can change the size of Digital Timer,
Count-down Timer, and Air Timer freely.
Here are steps to create an Analog Clock/ Digital Timer/ Count-down Timer/ Air Timer/ Logo. Take
Analog Clock as an example.
Gefei Tech. Co., Ltd
11 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
Step 1- Click the button of the needed
object. For example, click the
button of “Analog Clock”.
Step 2- And hold the mouse from
top to bottom to drag a frame
on the target screen.
Step 3- Release the mouse. Then System
creates an analog clock as the
position of the frame with fixed
size. You can change the position
of the clock freely. Other objects
are created as the same way.
Note：You can set the time for Air Timer. The details are described as following.
Air Timer can be configured. Press “Set Air Timer” button. Here is a message box popping out. See the
picture above. Enter the numbers on three blank areas separately. Then press “OK” button to submit
the data. The countdown timer is the interval time between air timer and current timer.
5.3.2.4 Delete an Object
Choose the unnecessary objects (channels/ clock/ Timer/ LOGO), and then press the button
Gefei Tech. Co., Ltd
12 / 30
MIO MVS-4HDMI
“
Quad Multi-viewer
Gefei-tech
” The selected one will be deleted immediately. The hot key is “Delete” on keyboard.
5.3.2.5 Clear All
Press the button “
”, clear up all the objects on the screen.
5.3.2.6 Screen
There are various functions in this area. The main are following:
1. Display all the channels ,clock, timer and logo;
2. Adjust the position of the clock and logo with a mouse in this area;
3. Adjust the position and size by dragging the edge of channels with a mouse in this area;
4. Adjust the position and size of audio meters and UMD of each channel by dragging the edge of
each audio meter or UMD with a mouse in this area;
5. Choose one or more objects in this area, before you change its parameters or take further
operation.
6. Any video channel can be directly and simply moved from one screen to another screen in
real-time.
5.3.2.7 Quick Tools
There are various quick tools for creating various layouts.
Do & Undo
: Undo, hotkey is “Ctrl+Z”;
: Do, hotkey is “Ctrl+Y”.
Alignment tools
All operations among these windows are aligned to the last selected one.
: Align Top
：Align Bottom
: Align Left
: Align Right
: Align Horizontal Center
: Align Vertical Center
: Horizontal Average
: Vertical Average
Gefei Tech. Co., Ltd
13 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
: Overspread with horizontal equal width
: Overspread with vertical equal height
The buttons below are not only for channels, but also for UMD & Audio Meters as well. The selected
audio meter is adjusted according to another one in the same channel. The buttons below can‟t be
applied for audio meters from different channels.
: Equal Width
: Equal Height
: Equal Width & Height.
Except these alignment tools, the software supports hotkey on the keyboard, such as direction key
“
”, in order to move channels in this area.
Full Screen
Choose one channel and double click it. Click the "send" button ,The selected channel will output in full
screen mode. When you want to quit the full screen mode, please use hot key “Ctrl+Z” or click
.
5.3.2.8 Layout Management
The system allows customers to save multiple user-defined layouts. The max number of layouts is 10
for the customer. Layouts can be saved or applied at any time.
Save Layout
Enter the name of layout in the blank area and click “Save” button. The layout is saved as a thumbnail
in the layout management area. The layouts of both screens are saved together at the same time.
Click the thumbnail apply the relevant layout.
If the name of the layout is already existed, the newly-saved layout will take place of the old one.
Edit Layout
Click the thumbnail of the needed layout, and adjust the layout as you needed. After all the operation,
click “save” button.
Gefei Tech. Co., Ltd
14 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
Delete Layout
: Delete button
Click delete button on the top of each layout thumbnail to delete the unnecessary layout.
Download Layout File
Click “Download” button and save the layouts you just designed in form of a BIN file. All the layouts
in layout setting area are saved as one file, so they can‟t be downloaded individually.
Upload Layout File
Click “Browse” button to find and upload the layout file you have downloaded before. After a massage
box appears to inform successful uploading, please refresh the page, and then layouts will appear in
layout display area as thumbnails. And apply a layout by clicking its relevant thumbnail. Note that the
latest uploaded layouts will replace the original one.
5.3.2.9
HDMI Output Resolution
Choose output resolution in the drop-down list.
HDMI output interface provides EDID detection from the monitor. And the resolutions from EDID are
highlighted in the dropdown list. See the picture shown above. The output resolution of HDMI signal
is up to 1920x1080p.
Supports output resolutions as following:
1024x768x60p，1280x720x50p/60p，
1280x800x60p，1280x1024x60p，1360x768x60p
1400x1050x60p，1600x900x60p，1680x1050x60p
1920x1080x50i/60i，1920x1080x50p/60p，
Gefei Tech. Co., Ltd
15 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
5.3.2.10 Audio Output Settings
.
The names of input sources are list in the drop-down list, and then choose one of them. When the
input source is HDMI signal, eight channels HDM audio signals can be embedded into the HDMI output
signal.
5.3.2.11 Ratio of Video
This function aims to adjust aspect ratio of video image. There are two types of video display: Full
channel and Original proportion.
Full channel means the video image will cover the entire channel and ignore the aspect ratio of video
signal.
Original proportion means the video image always keeps the aspect ratio of video signal even though
the ratio of the channel or the size of UMD and Audio meters are changed. So for SD input signal, the
aspect ratio of video image is 4:3；And for HD input signal, it is 16:9.
5.3.2.12 Ratio of Channel
This function aims to adjust aspect ratio of virtual channel. Aspect ratio contains 4:3, 16:9, and Free
Ratio.
4:3-The size of channels can be changed following the aspect ratio of 4:3.
16:9- The size of channels can be changed following the aspect ratio of 16:9.
Free Ratio- The size of channels can be changed freely following any aspect ratio.
5.3.2.13 UMD & Audio Meters Display
Check the box “UMD”. It will be shown within the channel, otherwise, not. The system supports the
UMD display. The further configuration can be completed the configuration of “OSD Elements” on
Gefei Tech. Co., Ltd
16 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
right-bottom of web page.
Check the box “G1”, and audio meters of G1 from HD/SD signal will be displayed within the channel,
otherwise, not.
Check the box “G2”, and audio meters ofG2 from HD/SD signal will be displayed within the channel,
otherwise, not.
Check the box “Locked”. The audio meters and UMD are locked with widow. So the audio meters or
UMD can‟t be operated separately. Otherwise, can.
5.3.2.14 Attach to point
If checking the box, there will be horizontal and vertical lines across the screen. So objects are moved
or adjusted by attaching to point or align to the line. You can set the rows and columns to change the
amount of lines and density of the cross points.
If un-checking the box, there will be no lines across the screen. So objects are moved or adjusted
freely.
Gefei Tech. Co., Ltd
17 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
5.3.2.15 Position and Size
Choose one object, the values of the channel‟s coordinates, width and height are shown on the right
of web page, which are for read only, and cannot be adjusted so far.
5.3.2.16 Set Air Timer
Set Air Timer for screen . First, press “Set Air Timer” button. Here is a message box popping out. See
the picture above. Enter the numbers on three blank areas separately. Then press “OK” button to
submit the data. The countdown timer is the interval time between air timer and current timer.
5.3.2.17 OSD Elements
Click the button “
”，prompting the dialog box as following:
Do select the needed channel or all channels in the drop-down list before every operation.
Gefei Tech. Co., Ltd
18 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
UMD Settings
First, select the needed channel in the drop-down list. The system supports the single programmable
UMD display. Two kinds of UMD mode are provided. They are static UMD via text upload and dynamic
UMD via TSL protocol.
1) Static UMD: Choose “Network” in the drop-down list, and click “Settings”.
Upload UMD Text
Type the characters in blank bar, change color of characters. Click “OK” to submit characters after all
parameters are settled and all characters will be displayed in UMD bar.
To clear the UMD
Enter a “space”, and then click “OK”, the character in UMD bar will be cleared.
2) Dynamic UMD: Choose “TSL” in the drop-down list and click “Settings”.
The function is reserved
Tally Settings
Two kinds of Tally mode are provided. They are Static Tally and Dynamic Tally.
Choose “None” in the drop-down list
The Tally function is disabled and Tally turns gray.
Gefei Tech. Co., Ltd
19 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
Via GPI-Static Tally
Static Tally is applied with DB15 interface. Based on the GPI lever for Tally, you can choose Low lever
or high lever in the drop-down list.
1) Choose “Low level” in the drop-down list to enable static Tally.
When there comes a low-level GPI, the TALLY area will turn light red; otherwise, dark red. Low
level is the voltage which higher than -5V and Lower than 0V. Users can choose the modified
channel from drop-down list.
If there is not a low-level GPI signal, the Tally area will turn dark red.
If there is a low-level GPI signal provided, the Tally area will turn light red.
2) Choose “High level” in the drop-down list to enable static Tally.
The function is reserved
3) Via Ethernet-Dynamic Tally
Choose “TSL Network” in the drop-down list
The function is reserved
Adjustment the transparency of Audio and UMD
Choose the target channel or all channels from the drop -down list.
In this area, users can modify the transparency of audio meters or UMD of each channel. Choose the
channel which needs to modify from the drop-down list, put the mouse on the cursor and drag it to the
assigned position; or you can fill in the certain parameter ranging from 0 to 15, and press “Enter” on
keyboard. “0” stands for full transparency and “15” stands for opacity
Attach to edge
Check “Attach to Edge”, when the audio meters and the UMD are located at the bottom edge of the
image, let the audio meters and the UMD cling to the edge which make the image be shown
completely. If not, UMD and audio meters are overlaid on image.
Gefei Tech. Co., Ltd
20 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
Display settings
Choose the target channel or all channels from the drop -down list.
Check the box “AFD Information” and AFD information will be overlaid on the top of the channel,
otherwise, not. AFD information is shown in the form of picture, according to the AFD code inside of
input signal.
Check the box “Input Format”, and input resolution will be overlaid on the top of the channel,
otherwise, not. Input resolution is shown as PAL/NTSC/720p/1080i/1080p.
1080i
Check the box "Underscan" to make effect for selected channel.
Check the box “Safe Marker”. The picture of HDMI signal is marked with 16:9 safe area markers, and
the picture of HDMI signal is marked with 4:3 safe area markers, otherwise, not.
Check the box “Border”, the selected channel is showed with border; otherwise, not. The border color
of each channel can be configured freely. Please see the title below.
Adjust Border Color
Choose the target channel or all channels from the drop -down list, and click “Modify” to appear a color
palette. Select the needed color and click “OK”. Then the current border color is changed to the one
you selected.
Gefei Tech. Co., Ltd
21 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
5.3.2.18 Extended Settings
Click the button “
”，prompting the dialog box as following:
Set Color Parameters
Brightness: to set the brightness and darkness of picture. The range is from -512 to 511.
Saturation: to set the color of picture. The range is from 0 to 511.
Contrast: to adjust the clarity of picture. The range is from 0 to 511.
Restore default button: to restore the factory default settings.
Put the mouse on the cursor and drag it to the assigned position; or you can fill in the certain value,
and press “Enter” on keyboard
Series Ports Settings
Gefei Tech. Co., Ltd
22 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
The function is reserved
Timing Settings
LTC,GPS and NTP the function is reserved
If check the box “Local”, the analog clock and digital timer are controlled by computer which also
accesses to the web control of MIO MVS-4HD through RJ45 interface. There are two items that
required notice. First, the local IP address of computer should be configured in the same network
segment as MIO MVS-4HD. Second, refresh the web page after checking the box “Local”, in order to
submit the current time of computer to MIO MVS-4HD. The factory setting of timing mode is Local
timing. Check the box “Local”, the local timing function is enabled, otherwise, not.
Upload Custom Picture
The function is reserved
5.3.2.19 Save
Click the button “
Gefei Tech. Co., Ltd
”,save "parameters setting area" parameter.
23 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
5.3.3 Detection Settings
：Check all the boxes for channels
：Selected will be clear, the others will be selected.
：Cancel all the checks
：Restore Factory Setting
：Check all the boxes for detection settings of selected channels
：Cancel all the checks for detection settings of selected channels
MIO MVS-4HD Series provides two kinds of warning mode: texts and small icons. And only one mode
takes effect at a time. Text is shown at the bottom of each channel. Video warning icon is shown at left
edge of each channel, while audio warning is at the right edge.
The video and audio input of each channel can report signal status and validity, with detection of (text
and icons):
Gefei Tech. Co., Ltd
24 / 30
MIO MVS-4HDMI
Quad Multi-viewer
(1) Loss of signal:
Gefei-tech
and
(2) Video frozen:
and
(3) Video black:
and
(4) Audio overload:
and
(5) Audio in silence:
and
Several channels can be configured at the same time. If the detection parameters of each channel
differ from others, the configuration should be completed separately.
5.3.3.1 Audio Detection
Measure unit of digital audio is dBFS（dB Full Scale）. 0dBFS is the maximum audio level, corresponding
to +24dBu of analog audio.
Audio Overload
It will prompt a warning picture as soon as the audio level overloads the threshold you have settled.
It provides 8 audio channels detection. And there is a box in front of each audio channel. This
detection will take effect only the box is checked. The threshold and duration of detection can be
configured for detection of each audio channel. The threshold means a maximum audio level. When
actual volume is above this threshold, the system will prompt warning of audio overload.
Gefei Tech. Co., Ltd
25 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
Audio in Silence
It will prompt a warning picture as soon as the audio level lowers the threshold you settled. It provides
8 audio channels detection. And there is a box in front of each audio channel. This detection takes
effect only if the box is checked. The threshold and duration of detection can be configured for
detection of each audio channel. The threshold means a minimum audio level. When actual volume is
below this threshold, the system will prompt warning of audio in silence.
5.3.3.2 Video Detection
Loss of Signal
It prompts a warning picture as soon as signal is lost. This detection takes effect only if the box is
checked.
Video Frozen
It will prompt a warning picture as soon as the regular pixels ratio of the image is lower the threshold
you have settled. This detection will take effect only if the box is checked. The threshold and duration
of detection can be configured. The threshold means the frozen pixel percentage in one frame.
Video Black
It will prompt a warning picture as soon as video level is lower the threshold. This detection will take
effect only if the box is checked. The duration of detection can be configured.
5.3.4 User Configuration
The software provides password-protected function. The initial user name is admin, and the initial
Gefei Tech. Co., Ltd
26 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
password is 000000. Users can modify the password; maximum password length is 12 bits. When you
modify the password successfully, information will prompt as "The password is altered successfully. It
will take effect when you login next time."
The function of download alarm diary is reserved.
5.3.5 Network Configuration
Change IP address
User can modify the IP address. If modified successfully, the system prompts a message box labeled
"Network has been configured successfully, please turn off the power and restart the device again.”
Gefei Tech. Co., Ltd
27 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
Restart the device, enter the new IP address in IE address and the web software will be opened.
Change manager IP for Voice Alarm
Configure the “Manager IP” to be the local IP address of computer for Voice Alarm. The computer and
MVS series should be in the same network segment. And Trap common and Trap port are for SNMP of
voice alarm. Do not change them.
Change NTP IP for NTP Timing
Configure the “NTP Server” to be the IP address of NTP server for NTP timing. And the NTP server and
MIO MVS series should be in the same network segment.
Upgrade firmware of system
User can also upgrade system under this label. Before the upgrade, the anti-virus software and
firewall have to be closed to make sure that the upgrade data is transmitted to MVS series system
without rejection. Windows 2003, Windows XP, Windows Vista and Windows 7 system are strongly
recommended to upgrade the system with Internet Explorer.exe.
There are two items for upgrading, such as main DSP, slave DSP , if there are new version released,
we will supply 1-2 files named according to the items name. Each item should be upgraded separately
one by one from main DSP. Power and network cannot be cut off during upgrading. When system is
upgraded successfully, please turn off the power and restart the device again. It takes about 5minutes
to upgrade slave DSP, and about 5 minutes to upgrade main DSP
Upgrade Text file for UMD font
The” Font” item means you can refresh the font style from your PC system. So as to upgrade the
software, you can update the font for Font item. The amount of data of font file must be less than 6MB.
Before the upgrade, the anti-virus software and firewall have to be closed to make sure that the
upgrade data is transmitted to MIO MVS-4HDMI series system without rejection.
5.3.6 Help
Show the version of firmware.
Gefei Tech. Co., Ltd
28 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei Tech. Co., Ltd
Gefei-tech
29 / 30
MIO MVS-4HDMI
Quad Multi-viewer
Gefei-tech
Contact Us
Technical support:
Tel: 010-58858188
Fax: 010-58858189
Website
www.gefei-tech.com
E-mail：[email protected]
Address:
Gefei Tech. Co., Ltd
A-603 Power Creative Plaza
NO.1 Shangdi E.Rd.
Haidian District, Beijing 100085
To find more information, please visit www.gefei-tech.com
Gefei Tech. Co., Ltd
30 / 30