advertisement
avfgroup.com
470114 rev02
45kg
99lb
STOP
Read through ALL instructions before commencing installation.
If you have any questions about this product or issues with installation, contact the customer services helpline before returning this product to the store.
This TV Wall Mount is intended for use with televisions weighing Maximum
45kg (99lbs) . Use with products heavier than maximum weight may result in instability causing possible injury.
CUSTOMER SERVICES HELP LINE NUMBER:
+44 (0) 333 320 0463 (UK)
1-800 667 0808 (USA)
AVF Group Ltd.
Hortonwood 30, Telford, Shropshire, TF1 7YE, England AVF Group, Inc.
2775 Broadway, Cheektowaga, Buffalo, New York,14227 USA
Fit the TV Brackets
Assembly Overview
Marking Wall for Drill Points
Hang the TV
Fit the Wall Rail
Suitable Wall Types
Solid Wall Wood Stud
Index
6
7
8
4
5
1
2
3
Measure the TV fixing holes Width and Height
Preparing the TV Brackets
Fitting the TV Brackets
Marking Wall for Drill Points
Fitting the Wall Rail
Fitting the Wall Rail Covers
Hanging the TV
Hide the TV Release Cords
Retain all packaging in case the product needs to be returned.
Contents may vary from photography / illustrations.
You will not need all these parts, so expect there to be some left over depending upon the specification of your TV.
This product is intended for indoor use only. Use of this product outdoors could lead to failure and personal injury.
It is the responsibility of the installer to ensure that the mounting wall is of a suitable standard and void of any services (eg gas, electricity, water etc).
AVF accept no responsibility for any damage or loss caused by installing this product in a substandard wall.
Tools Recommended
Stud Finder
Ø3mm (1/8”)
Wood
Ø10mm (25/64”)
Masonry
TV Screws, Reducers and Spacers
D
1 x4 D
2 x4 E
1 x12 E
2 x4
M4
F
1 x4
M4
F
2 x4
M4
F
3 x4
M5
F
4 x4
M6
F
5 x4
M6
F
6 x4
M6
F
7 x4
M8
F
8 x4
M8
F
9 x4
M8
F
10 x4
B
C
Boxed Parts
A
C
B
TV Release Cord
G x4 H x4 I
1
Measure the TV fixing holes Width and Height
75 - 400mm X
TV Fixing Holes
75 - 400mm Y
If width X is greater than 400mm or height Y greater than 400mm
STOP installation now and contact the customer helpline
You are provided with 4 diameters of TV fixing screws M4 , M5 , M6 and M8.
Determine the screw diameter that fits and remember for step 3.
M4
= F
1
F
3
M5
= F
4
M6
= F
5
F
7
M8
= F
8
F
10
2
Preparing the TV Brackets
IMPORTANT: Must be done before fitting brackets to your TV.
Loosen the TV Levelling Screw enough so that you can push the catch up to its maximum height (as shown).
To ensure maximum tilt is possible after installation you will need to ensure that your TV does not clash with the wall.
Clash
Top Bottom
No Clash
Top Bottom
Top Bottom
No Clash
3
Fitting the TV Brackets
No Spacers
For TVs with flat / unobstructed back.
Spacers
E
1
/E
2
For TVs with irregular / obstructed back.
WARNING
TV TV TV TV
If your TV has an irregular/obstructed back or if you have any issues fitting to the back of your TV with the supplied screws, please call the customer services helpline.
For easy access to some of the TV fixing holes, follow the procedure on the next page .
F
1
- F
10
D
1
D
2
Top
E
2
E
1
If required
Attach the brackets to the back of your TV using suitable screw, reducer and spacer combinations.
Easy Access to TV Fixing Holes
Disassembly and Reassembly
You must fully reassemble the TV Brackets when you have finished fixing them to the back of the TV.
4
Marking Wall for Drill Points
Before marking any drill points you will need to determine the wall type that you have, either
Solid Wall or Wood Stud Wall. Ensure the drilling area is free from mains services
(Gas / Electric / Water).
Use your Wall Rail as a template to mark the drill points.
i ii
A
B
C i Measure, in mm, from the bottom of the TV Bracket to the bottom of your TV. This will give you A .
Decide at what height you want the bottom of the TV to be above the floor in mm. This will give you B .
ii To work out the correct height C , in mm, to mark the drill points, use the sum C=A+B+370 .
I
If fixing to a solid wall use the four fixing holes shown.
If fixing to a wood stud wall you must place the Wall Rail so that it spans two wood studs.
Ensure each screw is in the centre of each wood stud (only two screws required for wood stud installation).
Before you drill make sure you are happy with the position and ensure all markings are correct and level.
12.5mm (1/2”) Min
50 x 100mm (2 x 4”) Min
100mm 4” Min
6
Fitting the Wall Rail Covers
C
7
Hanging the TV
Fully extend the TV Brackets before connecting the TV.
i ii
C
Extend Arm Extend Catch
i ii iii
Click!
If the catch doesn’t click into place when you connect your
TV, pull the top of your TV forward to seat it correctly.
When the catch has clicked into place beneath the wall bracket your TV will be fully secured to the wall. You cannot accidentally unhook your TV.
8
Hide the TV Release Cords
These cords are for removing the TV only.
They MUST be positioned as shown, until required, to avoid accidental usage.
TV Levelling (optional)
If your TV needs levelling, only adjust the TV Levelling Screw on the low side of the TV. For example, if the left hand side of your TV is low, adjust the left hand
TV Levelling Screw only, until your TV is level.
Adjust Tilt Resistance (optional)
Adjust screws to achieve perfect tilt resistance if required. Ensure all screws are adjusted equally. You may need to remove the TV from the wall to gain easy access to the screws.
The installation of your TV Wall Mount is now complete.
The rest of this instruction leaflet is operation and adjustment advice for your
TV Wall Mount. It is recommended that you keep these instructions in a safe place so you can refer to them at a later date if required.
Use in conjunction with your Handy User Guide .
For future reference, you can store your Handy User Guide in the groove on the Wall Rail.
i
To Remove the TV
Fully tilt forward ii
Unclip TV Release Cords from the Wall Rail.
Grip screen centrally at top to tilt
iii
Pull both TV release cords at the same time to unlock the TV. Pull the bottom of the TV away from the wall so the catch cannot re-engage. Lift and remove the TV from the Wall Bracket.
Tilt
Grip screen centrally at top to tilt
i
Cable Access
Fully tilt forward ii
Grip screen centrally at top to tilt
Carefully pull the bottom of the TV away from the wall using two hands. Pull the TV bottom of the TV far enough away from the wall to allow access to the back of the TV. Hold the TV in this position whilst you attach or remove any cables. When finished lower the TV gently back to the wall.
advertisement
Related manuals
advertisement