advertisement
TRENDnet User’s Guide
Cover Page
TRENDnet User’s Guide
Contents
Product Overview .................................................................................2
How to Access the IP camera via IP Installer ........................................ 34
How to setup/access the camera behind a Router ............................... 35
Technical Specifications ...................................................................... 38
Troubleshooting ................................................................................. 40
© Copyright 2014 TRENDnet. All Rights Reserved.
Table of Contents
i
TRENDnet User’s Guide
Product Overview
Product Hardware Features
Camera Overview
TV-IP302PI
Shield
IR Lens
TV-IP302PI
Package Contents
TV-IP302PI
Multi-Language Quick Installation Guide
CD-ROM (Utility, Software & User's guide)
Power adapter (12V DC. 1A) (1.5M / 5 ft.)
Network cable (1.5 M/ 5 ft.)
RJ-45 coupler
Camera Mounting hardware
Features
The Outdoor Megapixel PoE Day / Night Internet Camera, model TV-IP302PI, provides powerful megapixel night vision in complete darkness for up to 15 meters (50 feet).
This camera is outdoor ready with an IP66 weather rated housing. The compact aluminum enclosure, a mere 4 inches long (10 cm), comes with an adjustable sun visor.
© Copyright 2014 TRENDnet. All Rights Reserved.
Camera Stand
Shield: It is used to protect the camera for the inclement weather.
IR Lens: IR lens for the camera.
Camera Stand: the mounting stand to hold the camera.
2
TRENDnet User’s Guide
Camera Connectors
Speaker
Out
GPIO
Port
Ethernet /PoE
Port
Microphone
In
BNC
Video Out
Power
Connector
Power Connector: Connects the power adapter to supply power to the camera if using non-PoE connection
BNC Video Out: Connect a CRT monitor or handheld monitor.
Microphone In: Connects an external microphone to receive the on-the-spot sound where the camera is installed
.
Ethernet/PoE Port: Plugs the network cable to connect to your local area network (LAN). If you are using the PoE, you must have the network cable connect to your PoE switch or PoE Injector.
GPIO Port: Connect external device. Please refer to I/O setting paragraph.
It's also used for IP camera reset. Please refer to Factory Default paragraph.
Speaker Out: Connects an external audio device (such as the active speaker) to deliver sound via the camera.
© Copyright 2014 TRENDnet. All Rights Reserved.
Application Diagram
TV-IP302PI
3
TRENDnet User’s Guide
Installation
Hardware Installation
Shield Installation
1. Align the notches on the sides of the IP camera to the shield.
TV-IP302PI
2. Once both notches are aligned with the shield, slide th4e shield forward.
© Copyright 2014 TRENDnet. All Rights Reserved.
3. Adjust the IP camera to fit the shield.
4
TRENDnet User’s Guide
Bracket Installation
1. Turn and lock the bracket into the mounting hole of IP camera. Use screws to fix the bracket to ceiling or wall, and turn the knob tightly to fix the angle of camera.
TV-IP302PI
Camera Installation
1. Insert the Installation CD-ROM into your computer’s CD-ROM drive to initiate the
Auto-Run program. Click the Install Camera.
LED Indicator
The green LED will be flash when power on the camera and if there is the data transmission.
2. Write down the MAC ID of the camera.
LED
Waterproofing
The camera is designed featuring waterproof. However, you need to protect the connectors from water soak. For example, you can tape the junction points of the connectors while you connect the cables or purchase a weatherproof cable/power cord protector.
© Copyright 2014 TRENDnet. All Rights Reserved.
5
TRENDnet User’s Guide
3. Plug in and connect the power adapter to the camera. If you are using the PoE to supply power to the camera, please skip to the next step. Click Next when you are done.
5. Wait while camera is searching.
TV-IP302PI
4. Connect a network cable to the camera’s network port and then to your router.
If you are using PoE, please ensure the cable is connected to a PoE switch or PoE injector.
6. The founded cameras will show on the screen. The camera already selected by default if you have only one camera installed. If you have more than one camera in the same Network, you will need to identify the camera by the MAC ID. Click
Next.
© Copyright 2014 TRENDnet. All Rights Reserved.
6
TRENDnet User’s Guide
7. Select "DHCP" option to assign an IP by DHCP server or Select "Fixed IP" to set IP address manually. Click Next.
TV-IP302PI
9. Type in the Password. The default password is “admin”. You must change the default password of the camera. Enter the default password: admin and enter the new password. The password must be between 8 and 32 characters.
(Alphanumeric: a-z, A-Z, 0-9), and confirm the new password by entering the password twice.
8. If you select "Fixed IP", fill out the IP address, subnet mask, default gateway, DNS server. Please ensure that the IP address of the camera and the computer must within the same network. Click Next.
10. Click “here” to access to the camera’s web page or click Next. It is recommended that you access the IP camera now if it was using a DHCP connection.
© Copyright 2014 TRENDnet. All Rights Reserved.
7
TRENDnet User’s Guide
11. Click Finish to exit the program or click Home to return to the main screen.
This device also supports the Mobile App. Using your mobile device to scan the
QR code to install the App.
TV-IP302PI
Configuration
Viewing Camera Basic Function
Open the Web browser on your computer (example showed in this User’s Guide is based on the Internet Explorer). In the Address bar, type the IP address you got from
"Camera Installation" chapter or found by IP Installer, and then press [Enter].
When the login window appears, enter the User name (admin) and Password and press OK to access to the main screen of the camera’s Web Configuration.
© Copyright 2014 TRENDnet. All Rights Reserved.
Note: if you are initially access to the camera, you will be prompted to install a new plug-in for the camera. Permission request depends on the Internet security settings of your computer. Click Allow and Install to process.
8
TRENDnet User’s Guide
After you login into the live screen of the camera, the main page will appear as below:
TV-IP302PI
“Speaker” to receive the on-side sound and voice from the camera.
"Off" to stop triggering. To switch between these two types of relay out, please refer to page 32 of the GPIO Setting session.
One the live view video, right click the mouse for the additional menu options.
The live screen of the IP camera configuration provides you with many useful information and functions, including: another window for your review first. Click disk icon to save the snapshot at the desire destination.
Video Refreshing Rate.
The default is 1/2x. video. (If the streaming 2 setting is closed on “AUDIO/VIDEO SETTING >> Video”, this option will not appear)
© Copyright 2014 TRENDnet. All Rights Reserved.
Snapshot: Save a JPEG picture
Record Start: Record the video in the local PC. It will ask you where to save the video. To stop recording, right-click the mouse again. Select “Record Stop”. The video format is AVI. Use Microsoft Media Player to play the recorded file.
Mute: Turn off the audio. Click again to turn on it.
The "mute" button does not affect the playback recording video. As long as the
"2-Way Audio" option in the audio setting is enabled, all the audio will be recorded into the playback video even you click "mute" in the live page.
Full Screen: Full-screen mode.
9
TRENDnet User’s Guide
Zoom: Enable zoom-in and zoom-out functions. Select “Enable digital zoom” option first within the pop-up dialogue box and then drag and drop the bar to adjust the zoom factors.
TV-IP302PI
Configuring the Camera Setting
To configure the camera, click on the live screen.
The Web Configuration contains the settings that are required for the camera in the left menu bar, including System Setting, Network Setting, Audio/Video Setting, and
Event Setting.
Frame Buffer mSec: This function is to build a temporary buffer to accumulate several video frames. This function can make video smooth-going when the
Network speed is slow and lag. If you select “100”, then it plays video after 100 mSec when starting receiving images from camera. The slower of the Network is, the bigger value should be selected. The default value is null.
© Copyright 2014 TRENDnet. All Rights Reserved.
To return to the live screen, please click the button.
10
TRENDnet User’s Guide
System
System >> System Information >> Server Information
MAC Address: It indicates the IP Camera’s MAC address.
Server Name: The Camera name.
LED Indicator: Turn the LED light on or off by click the ON/OFF button.
Language: There are 5 languages options. When changing the language, it will prompt dialogue box for confirmation. Click "Yes" to proceed.
© Copyright 2014 TRENDnet. All Rights Reserved.
System >> System Information >> OSD Setting
TV-IP302PI
Time Stamp: Enable or disable the time that will show on the live screen.
Position: After enabling time stamp, you can select the position of time stamp on the live screen.
Text: Enable the Text option to have the desire text show on the camera live screen.
Text Edit: Click it to call out "text edit" window:
Text: Key in the words you want to show on the live screen.
Opaque: Set the background transparency of the text.
11
TRENDnet User’s Guide
System >> System Information >> Time Setting
TV-IP302PI
when you want to synchronize the IP camera time with PC time again, please select this option and click "Apply".
Manual: Type in the date and time, and click "Apply".
System >> User Management
Server Time: It shows current IP camera server time.
Date Format: Select the date display format.
Time Zone: Select your time zone. It affect server time when you use "NTP" time.
Enable Daylight Saving: select the start and end daylight saving time.
NTP: Type in the IP address of the NTP server and interval time. The time of the
IP camera will be synchronized with NTP server time. To use this option, if the
NTP Server is under WAN, the IP camera must be set to access WAN ( Using the
WAN IP that provide by your ISP provider, or setup by UPnP Port Forwarding
(page 18)
Synchronize with PC's time: In "Date" and "Time" column it shows your current
PC time. Click "Apply" to make the IP camera time the same with PC time. Note that IP camera will not check with PC at every moment automatically. Every time
© Copyright 2014 TRENDnet. All Rights Reserved.
Direct Video Stream Authentication:
To steam the video directly without going through the configuration page, you can access it via Internet.
Stream 1 Video: http://camera_ip_address:port/stream1view.htm
Stream 1 Video: http://camera_ip_address:port/stream2 view.htm
12
TRENDnet User’s Guide
Enable Password Protection:
Yes: User needs to enter user name and password to stream the camera.
No: User can stream the camera without entering the username and password.
Add user: Enter the username and password to add guest users to access the camera. The guest user can only view the live view video and is not allowed to do any configuration.
User List: List all users that were added into the camera. Click “Edit” to
modify the user information. Click “Remove” to remove the users from the list.
System >> Tools
TV-IP302PI
Firmware Upgrade:
To update the firmware, click “Browse” to select the firmware, then click
“Upgrade” to proceed. Please do not disconnect power or Network cable during firmware upgrading.
System Reboot: Click Reboot to reboot the IP camera.
Factory Reset: Click Reset to reset all the settings back to factory default value
Configuration:
Backup: Click Backup to save the configuration to your computer.
Restore: Click "Browse..." to select the configure file from your computer then click Restore to restore all setting
NETWORK
© Copyright 2014 TRENDnet. All Rights Reserved.
13
TRENDnet User’s Guide
Network >> Network Setting >> IP Address Setting
DHCP: Select this option when your network uses the DHCP server. When the camera starts up, it will be assigned an IP address from the DHCP server automatically.
Static IP: Select this option to type in IP address, subnet mask, gateway, and DNS manually. Default IP address is 192.168.10.30 if the camera doesn't connect with
DHCP server. DNS (Domain Name System) translates domain names into IP addresses. Enter the Primary DNS and Secondary DNS that are provided by the
ISP.
Network >> Network Setting >> IPv6 Setting
IPv6 is a newer numbering system that provides a much larger address pool than
IPv4, which accounts for most of today’s Internet traffic. You can manually enter IPv6 address , enable DHCPv6 to get IPv6 address automatically.
© Copyright 2014 TRENDnet. All Rights Reserved.
TV-IP302PI
Manually setup the IPv6 address: You can set up IPv6 manually by enter IP
Address, Gateway, and DNS.
DHCPv6: If you have a DHCPv6 server, enable this option to assign the IPv6 from server. The assigned IP address will be displayed
IPv6 Address: A virtual IPv6 address generated by the IP camera. This virtual IPv6 address cannot use on WAN. To access the IP camera via IPv6 address, open a web browser and type in http:// [IPv6 Address] in the address bar. The [ ] parentheses mark is necessary for IPv6 address.
Network >> Network Setting >> Port Setting
Web Page Port: Setup HTTP web page connecting port which is also video transmitting port (Default: 80)
HTTPS Port: Setup HTTPS connecting port (Default:443)
Network >> Network Setting >> Web Authentication
The camera supports two levels of authentication, Basic and Digest. The Basic option having the username and password transmitted as plain text. The digest option encrypted username and password during data transmission. The default authentication is set to Digest.
14
TRENDnet User’s Guide
Network >> Network Setting >> UPnP Network >> Network Setting >> RTSP Setting
TV-IP302PI
UPnP:
This IP camera supports UPnP (Universal Plug and Play) which is a set of computer network protocols that enable the device to device interoperability
UPnP Port Forwarding:
When the camera is installed under a router, enable UPnP Port Forwarding to let the router open ports so that the video streams can be sent out from a LAN. Set
Web Port, Http Port, and RTSP port, and make sure your router supports UPnP and the function has been activated.
After type in the port number and click "Apply", the port forwarding status will display beside the port column. There are three status will show.
Registered successfully: UPnP port forwarding setting succeeds.
The router doesn't support UPnP Port Forwarding: The camera can detect the router, but router return a message that it does not support UPnP Port
Forwarding.
The router is with some problems. Please reboot it: The camera cannot detect the router. Please check your router.
If this router has a WAN IP, this function allows the camera to do WAN access. In the address bar of browser, key in: "https:// (router WAN IP) : (external web port) /" to access the IP camera.
© Copyright 2014 TRENDnet. All Rights Reserved.
RTSP Server:
Enable it, then you can access camera and get image via RTSP protocol.
If you have a media player that supports RTSP protocol, you can use it to receive the video streaming from IP camera. The RTSP address can be set for two streamings respectively.
RTSP Authentication:
"Disable" means everyone who knows your camera IP Address can link to your camera via RTSP. No username and password are required.
Under "Basic" and "Digest" authentication mode, the camera asks the user to give username and password before allows accessing. The password is transmitted as plain text under basic mode, which provides a lower level of security than under digest mode. Make sure your media player supports the authentication schemes.
RTSP Port: It's used for TCP connection. Setup port for RTSP transmitting
(Default: 554)
RTSP Start and End Port: It's used for UDP connection. Setup port for RTSP transmitting (Default: 5000, 9000)
15
TRENDnet User’s Guide
Network >> Network Setting >> Multicast Setting (Based on the RTSP Server)
Multicast is a bandwidth conservation technology. This function allows several users to share the same packet sent from IP camera. To use Multicast, appoint IP Address and port here. TTL means the life time of packet, The larger the value is, the more user can receive the packet.
To use Multicast, be sure to enable the function "Force Multicast RTP via RTSP" in your media player. Then key in the RTSP path of your camera: "rtsp://(IP address)/" to receive the multicast.
Network >> Network Setting >> ONVIF
Under ONVIF connection, the video will be transmitted by RTSP. Be sure to enable the RTSP server in IP setting, or you're not able to receive the video via ONVIF.
© Copyright 2014 TRENDnet. All Rights Reserved.
TV-IP302PI
ONVIF:
Choose your ONVIF version. The two devices that use ONVIF to communicate should be set to the same version.
Security:
Select "Disable", then the username and password are not required when accessing the camera via ONVIF. Select "Enable", then username and password are necessary.
RTSP Keepalive:
When the function is enabled, the camera checks once in a while if the user who links to the camera via ONVIF still keeps connecting. If the connection had been broken, the camera stops transmitting video to user.
Network >> Network Setting >> Bonjour
This function enable Safari browser's bookmark to link to this IP camera. The Bonjour name is the name that display in the bookmark. Please note the Bonjour function on
Safari browser does not support https protocol. If you selected “https” mode, you will see the camera appears on Safari’s bookmarks but will not be able to access the camera.
Network >> Network Setting >> LLTD
If your PC supports LLTD, enable this function then you can check the connection status, properties, and device position(like IP address) of this IP Camera in the network map. In Windows Vista or Windows 7, you can find LLTD through the path:
16
TRENDnet User’s Guide
Call out the Control Panel → Network and Internet → Network and Sharing Center →
Click "See full map".
Network >> Advanced >> HTTPS
When the users access cameras via Https protocol, the transmitted information will be encrypted so that the security level is arisen.
You can select the connection type.
Http: user can access the camera via Http path.
Https: user can access the camera via Https path but cannot via Http path.
Http & Https: Both the Http and Https path can be used to access the camera.
When you change the setting of connection type, it may cause connection error or disconnection error if you switch the protocol directly. Therefore, Http &
Https mode is necessary. If you want to change from Http to Https, please switch to “Http & Https” mode first, and then switch to “Https” mode. Same method when you change from Https to Http.
The Https protocol has certificate verifying mechanism. When the user access a website via Https, the browser will check the certificate of that domain and verify its trustiness and secure.
Certificate generation process:
1. Remove the existing certificate: Before you generate a new certificate, please remove installed one. Select "Http" connection type and click "Remove". If a dialog box pops up to ask you to confirm, click “Yes”.
TV-IP302PI
2. Created Request: Fill in the following form and click “apply”.
© Copyright 2014 TRENDnet. All Rights Reserved.
3. After you generate a certificate request, if you choose to turn it to the trusted third-party to verify, please click “Content” and copy all the request content.
17
TRENDnet User’s Guide
4. According to the certificate source, there are two ways to install the certificate.
If you had sent the certificate request to do sign and received a signed certificate, please click” browse” and find the certificate file in your computer. Click “Apply” to install it.
If you choose to generate a self-signed certificate, fill in the following forms and set validity day, click “Apply” to finish installed it.
TV-IP302PI
After finishing installation, you can click “Content” to call out and check the certificate content.
5. To use Https to access camera, open your browser, and key in "https://(IP address)/" in the address bar. Now your data will be transmitted via encrypted communications, and the browser will check your certificate status. If it shows you a warning message. The warning message meant that the certificate is selfsigned or signed by distrusted institution. Click Continue to this website to view the view the camera.
© Copyright 2014 TRENDnet. All Rights Reserved.
Network >> Advanced >> SNMP
SNMP (Simple Network Management Protocol) provides a simple framework for administering networked hardware. To manage the IP camera, you have to prepare a
MIB browser or similar tools first. SNMPv1, SNMPv2c, and SNMPv3 can be enabled simultaneously.
The following examples are based on MG- SOFT MIB Browser. Depending on your
MIS Browser, you may see different interface and options. Please refer to the user manual of your MIB Browser.
SNMPv1 and SNMPv2:
The term "Community name" in SNMPv1 and SNMPv2c can be roughly regarded as key. The person who has the community name has the authority to read or edit the information of IP camera via SNMP.
Click the box to enable SNMPv1 or SNMPv2c protocol, and specify the community name for write (read and write) and read (read-only). The user who use read community name to access the IP camera cannot modify any data of the camera. The community name can be any English characters and numbers, and must be shorter than 31 bits.
18
TRENDnet User’s Guide
SNMPv3:
SNMPv1/SNMPv2 Trap:
TV-IP302PI
For data security reason, the authentication and encryption assurances are added when developing SNMPv3. The user has to give not only the security name(similar with "community name" in v1&v2c) but the password in order to access the IP camera. Please set security name, authentication type, authentication password, encryption type, encryption password of write and read respectively. The security name can be any English characters and numbers, and must be shorter than 31 characters. The password must between 8 to 64 characters.
Different from in SNMPv1 and v2c, the user have to create an account when using SNMPv3. In the account parameters, key in the security name and password you set in the camera to get accessing.
.
© Copyright 2014 TRENDnet. All Rights Reserved.
Trap is a mechanism that allows a managed device to send messages to manager instead of waiting passively for polling from the manager. Specify the trap event.
When those events happen, the camera will send the ring message to the Trap
Address, which is usually the manager's IP address. Trap Community means the community that can receive the trap message.
Note: Trap Address must be under the same LAN with IP camera.
Cold Start: The camera starts up or reboots.
Setting changed: The SNMP setting is changed.
Network Disconnected: The network connection was broken down. (The camera will send trap messages after the network being connected again)
V3 Authentication Failed: A SNMPv3 user account tries to get authentication but failed. (Due to incorrect password or community)
19
TRENDnet User’s Guide
Network >> Advanced >> IP Address Filter Network >> Advanced >> QoS/DSCP
TV-IP302PI
You can allow or deny an IP address or even a range of the IP address to access the IP camera. If you would like to deny a range of IP address but would allow an IP within that range can access the camera, please setup the allow IP address in the 1 st
priority and set the deny range of IP address as 2 nd
priority as example below.
© Copyright 2014 TRENDnet. All Rights Reserved.
DSCP specifies a simple mechanism for classifying and managing network traffic and provide QoS on IP networks. DSCP is a 6-bit in the IP header for packet classification purpose.
The number 0~63 for Live Stream, Event / Alarm, and Management represent the ratio that the bandwidth is divided. For example, if you set 5, 10, and 20 for these three items, then the bandwidth of these items is 5:10:20. The item getting more bandwidth has lower probability to be delayed. There is no difference between setting "0, 0, 0" or "63, 63, 63" because under these two setting the three items will get equal bandwidth (1/3).
The three stream control the protocols respectively:
Live Stream (Video and audio) : RTP / RTSP
Event/Alarm : FTP / SMTP / SAMBA / SIP
Management : HTTPS / HTTP / SNMP
Note: The "Management" stream handles both the live view and the setting area of the web page on which the data is transferred via http/https protocol. If you prefer to distribute more bandwidth when using the web browser to watch the live video, please adjust the Management Stream instead of Live Stream.
20
TRENDnet User’s Guide
Network >> Advanced >> IEEE 802.1x Network >> PPPoE & DDNS
TV-IP302PI
IEEE 802.1x is an IEEE standard for port-based Network Access Control. It provides an authentication mechanism to device wishing to attach to a LAN or WLAN. To use this function, you need a device to build IEEE 802.1x LAN at first.
The EAPOL protocol support service identification and optional point to point encryption over the local LAN segment.
Please check what version of the authenticator and authentication server support.
This camera supports EAP-TLS method. Please enter ID, password issued by the CA, then upload related certificates.
© Copyright 2014 TRENDnet. All Rights Reserved.
PPPoE
21
TRENDnet User’s Guide
Select “Enabled” to use PPPoE. Type in the username and password for the ADSL connection.
Send mail after dialed: When successfully connecting to the internet, it sends a mail to a specific mail account. As for the mail account setting, please refer to Server setting page.
DDNS
© Copyright 2014 TRENDnet. All Rights Reserved.
TV-IP302PI
This camera supports following Dynamic DNS server: Dyndns.com, 3322.org, noip.com and IPTECNO DDNS.
Enable DDNS, and select a DDNS provider. Some providers will ask you to register and get an account before you use their service. Fill in the user name, hostname, and password (if need). If setting up IP schedule update too frequently, the IP may be blocked. In general, we suggest set schedule update to once a day (1440 minutes).
After click "Apply" the setting.
DDNS Status:
Updating: Information update
Idle: Stop service
DDNS registration successful, can now log by http://<username>.no-cp.com:
Register successfully.
Update Failed, the name is already registered: The user name has already been used. Please change it.
Update Failed, please check your internet connection: Network connection failed.
Update Failed, please check the account information you provided: The server, user name, and password may be wrong.
22
TRENDnet User’s Guide
Network >> Event Server
© Copyright 2014 TRENDnet. All Rights Reserved.
TV-IP302PI
The settings of Email, FTP and SAMBA are used when the event happens, schedule snapshot executes, or the alarm input is triggered. Select the item to display the detailed configuration options. You can configure either one or all of them.
Mail Setting
Login Method: Select "Anonymous" to disable the authentication feature, or select "Account" and then enter the Username and Password according to the mail server configuration.
Mail Server: Enter the mail server address. For example, myserver.com. If you are using a free mail service (e.g. Google gmail.com®, Yahoo®,
Hotmail®), please enter the SMTP server address from the service provider.
Username & Password: Enter the sender's username and password to login the mail server. For free mail server, please the email address as the username.
Sender's Mail: Enter the email address of the user who will send the email.
Receiver's Mail: Enter the mail address of the user who will receive the email. Use semicolon to separate each address. It can contain up to 64 characters in the column.
Bcc Mail: Enter the mail address of the blind carbon copy receiver.
23
TRENDnet User’s Guide
Mail Port: Assign the SMTP port in the text box. The default SMPT port is 25.
For the free mail service, please enter the correct port number from the service provider.
Wan IP Change Notification: Enable this option, then a mail will be sent if the Wan IP of router above the camera is changed.
Secure Connection: If the mail server requires an encrypted connection, you should select the SSL option. TTLS is an extension to plain text communication protocols. It offers a way to upgrade a plain text connection to an encrypted (TLS or SSL) connection.
Click Apply to save the setting, then use Test button to test the server connection. A message box will tell you “OK!” if it works, and a test e-mail will be sent to receiver’s mail address.
FTP Setting:
TV-IP302PI
Mode: In PORT mode, the FTP server builds the connection to the user’s data port actively. However, from the user-side firewall’s standpoint, the action of connecting from FTP server is often considered to be dangerous and should be blocked. In PASV mode, the problem is solved: The FTP server waits for the data transmission connection built by the user. Make sure that the server supports the mode you select.
Create the folder: Select Yes, then folders will be created folder by date under your FTP path.
Click Apply to save the setting, then click Test button to test the server connection. A message box will tell you “OK!” if it works, and a test file will be uploaded to FTP server.
Samba Setting:
FTP Server: Enter the IP address of the target FTP server.
Username & Password: Enter the username and password to login into the
FTP server.
Port: Enter the port number used for the FTP server.
Path: Enter the destination folder for uploading the images. For example,
/302PI.
© Copyright 2014 TRENDnet. All Rights Reserved.
Location: Enter the path of the shared folder.
Workgroup: Type in the workgroup name of the computer.
Username & Password: Enter the username and password to login into the
Samba.
Create the folder: Select Yes, then folders will be created by date under your Samba Server.
Click Apply to save the setting, then use Test button to test the server connection. A message box will tell you “OK!” if it works, and a test file will be created in the location.
24
TRENDnet User’s Guide
AUDIO/VIDEO SETTING
Audio/Video Setting >> Image Setting
TV-IP302PI
© Copyright 2014 TRENDnet. All Rights Reserved.
25
TRENDnet User’s Guide
Privacy Mask: For the security and privacy purpose, there are three areas can be setup for privacy mask. Click Area button first and drag an area on the above image, and remember to save your setting. The masked area will not show on both the live view and recording.
Brightness, Contrast, Hue, Saturation, Sharpness can be adjusted here.
AGC: Automatic gain control. The sensitivity of camera can adjusts with the environmental light. Enable this function and the brighter image can be got under dim light, but the level of noise may also increase.
Shutter Time: Choose as the location of your camera or fixed shutter time. The shorter the shutter time is, the less light the camera receives and the image becomes darker.
Sense-Up: This function increases the sensitivity of camera to get brighter image at night. The smaller the value you select, the slower the shutter speed becomes so that the image will get brighter, and moving subjects might be blurred.
Sense-Up option is only enabled when users select "outdoor" or "indoor" in shutter time option.
D-WDR: Digital Wide dynamic range. This function enables the camera to reduce the contrast in the view to avoid the dark zones resulting from over and under exposure.
Video Orientation: Flip, mirror, or rotate the image.
Day & Night: The camera can detect the light level of environment. If you choose
"Light Sensor Mode", the image will be turned to black and white at night in order to keep clear. To set light sensor mode, appoint a lux standard of switching
© Copyright 2014 TRENDnet. All Rights Reserved.
TV-IP302PI
D/N here. Current lux value is provided for reference. Under "Times Mode" the switch time of Color / Black and white is according to the given time. If you select
"Synchronize with DI input", the image turns to black and white when digital input is triggered. You can also control it by choosing "Color" or "B/W".
DNR: Digital Noise Reduction. This function is able to filter the noise and blur from the image and show a clearer view.
Note: When you select a number in "Shutter Time", actually the shutter time varies in a range and controlled by camera automatically. Following table shows the shutter time option and corresponding range.
Option
Outdoor
Indoor
Shutter Time Range (sec.)
1/10000 ~ Selected number in "Sense-up"
NTSC: 1/125 ~ Selected number in "Sense-up"
PAL: 1/100 ~ Selected number in "Sense-up"
1/30
1/50
1/60
1/100
1/10000 ~ 1/30
1/10000 ~ 1/50
1/10000 ~ 1/60
1/10000 ~ 1/100
1/125
1/250
1/500
1/1000
1/10000 ~ 1/125
1/10000 ~ 1/250
1/10000 ~ 1/500
1/10000 ~ 1/1000
* Sense-up options: 1/30, 1/15, 1/10, 1/5
26
TRENDnet User’s Guide
Audio/Video Setting >> Video Setting
Video Settings
© Copyright 2014 TRENDnet. All Rights Reserved.
TV-IP302PI
Select the Video System (digital signal) and TV Output (analog signal).
Basic Mode of Streaming 1 and Streaming 2:
Resolution: 1280x800, 1280x720 , 640x480, 320x240, or 176x144
Quality: The higher the quality is, the bigger the file size is. It might affect
Internet transmitting speed if the file gets too large.
Video Frame Rate: The video refreshing rate per second. The max value is affected by the input resolution you choose.
Video Format: H.264, MPEG4, or M-JPEG.
RTSP Path: Set the RTSP output connecting route. You can use the RTSP address displaying beside the column to access this IP camera.
27
TRENDnet User’s Guide
Advanced Mode of Streaming 1 and Streaming 2:
Resolution: 1280x800, 1280x720 , 640x480, 320x240, or 176x144
Bitrate Control Mode: In CBR(Constant Bit Rate) mode, the bitrate keeps consistent all over the video. In VBR(Variable Bit Rate) mode, the bitrate changes with the complexity extent of the video data. VBR provides a better compression way and the file may be smaller.
However, the VBR file size cannot be predicted. The image may become broken or lagged when your bandwidth is not enough for the data quantity you selected.
Video Quantitative: The quality parameter of VBR. You can choose 1~10 compression rate. The higher the value is, the higher the image quality is.
© Copyright 2014 TRENDnet. All Rights Reserved.
TV-IP302PI
Video Bitrate: The quality parameter of CBR. You can choose 32kbps
~8Mbps. The higher the value is, the higher the image quality is.
Video Frame Rate: The video refreshing rate per second. The max value is affected by the input resolution you choose.
GOP Size: It means “Group of Pictures”. The higher the GOP is, the better the quality is.
Video Format: H.264, MPEG4, or M-JPEG
RTSP Path: RTSP output connecting route. You can use the RTSP address displaying beside the column to access this IP camera.
3GPP Streaming mode:
3GPP Streaming is designed for specific mobile viewing. To receive video via
3gpp, please remember to enable rtsp server in the "Network Setting" page.
3GPP mode fixed setting: 176 x 144 resolution, 5FPS, Video compression:
MPEG4, Audio compression: AMR.
3GPP Path: 3GPP output connecting route. If the IP address of your camera is 192.168.1.160 and you type in "3g" in the column, the 3GPP path will be
rtsp://192.168.1.160/3g.
Audio/Video Setting >> Audio Setting
IP Camera supports 2-way audio. Audio can be received by the microphone connected with IP camera and transmitted to remote PC. User can also send audio from remote computer’s microphone to IP Camera’s external speaker.
Two-Way Audio
28
TRENDnet User’s Guide
Select “Enable”, then you can see "Mic" and "Speaker" options on the live page.
The Audio compression format can be chosen from 3 options. You can also adjust the volume of 2-way audio.
EVENT CONFIGURATION
TV-IP302PI
Receive sound from IP Camera or speak to IP Camera
Click "Mic" check box to receive sound from IP Camera and click “Speaker” to talk to IP camera side. Please ensure both IP camera and the computer sides have the microphone and speaker installed to have this function work properly.
Event Configuration >> Motion Detection
© Copyright 2014 TRENDnet. All Rights Reserved.
29
TRENDnet User’s Guide
Area Setting: Click Area 1 /Area 2/Area 3 icon then draw the motion detection area on the live screen. If there is any motion detected in these areas, the
"Motion!" wording will show on the live screen. To clean the motion detection area, click Area 1 /Area 2/Area 3 icon again.
Sensitivity: Select motion detection sensitivity from 1 to 10.
Trigger Action (Area 1, Area 2, Area 3): When motion is detected, the camera can send video or snapshot to Email, FTP, Output device and Samba.
Subject: This subject will appear as the subject when sending the motion detected video or snapshot to email.
Interval: Each motion triggered in defined interval time. If you select "10 sec" here, once the motion is detected and action is triggered, the next motion will be trigger after 10 seconds. .
Based on the schedule: The motion detection will be triggered based on the schedule you define.
Event Configuration >> Motion Detection >> Record File
When an event happens, the IP camera can record a video clip or take snapshot, and then send the file to mail/ FTP/ Samba. Select what format you want to save.
AVI File (with Record Time Setting): Save AVI video file. The video length is according to the value you set in Record Time Setting.
JPEG File (Single File with Interval Setting): Save single JPEG picture file when event happens.
JPEG Files (with Record Time Setting): Only when you select "JPEG" in streaming
1 video format of Video Setting, this option can be enabled. Select this option to save several JPEG picture files, and the successive picture files cover a period of time according to the value you set in Record Time Setting.
© Copyright 2014 TRENDnet. All Rights Reserved.
Event Configuration >> Motion Detection >> Record Time Setting
TV-IP302PI
When a event happens, the IP camera can record a video clip or take snapshot, and then send to mail/ FTP/ Samba. Select the video recording length before and after event happens.
Event Configuration >> Motion Detection >> Network IP Check
Enter the target IP address and interval. The camera will base on the interval time to check the target IP address. If PIN failed 4 times, the camera itself will reboot.
30
TRENDnet User’s Guide
Event Configuration >> Schedule Event Configuration >> GPIO Setting
TV-IP302PI
1. I/O Connection
Please connect the GND & DO pin to the external relay (buzzer) device.
When no event happens, DO output is 5V (DO and GND are disconnected).
When the camera detects event happening and triggers external alarm, DO output is 0V (DO and GND are connected).
Schedule: Click on the week calendar to draw color. During the colored time, snapshot can be taken, and event trigger can be enabled if you do relevant settings.
Snapshot: Enable the snapshot function, then IP camera will take snapshot according to schedule. Select the snapshot saving way: E-mail, FTP, or Samba.
Interval: The interval between two snapshots.
File Name: Give the snapshot file name. The saved file will be named as: "(file name) - (saving date) - (saving time)"
© Copyright 2014 TRENDnet. All Rights Reserved.
31
TRENDnet User’s Guide
Please connect the GND & DI pin to the external trigger device.
If you select "N.O" in "Input sensor setting", when external devise or circuit makes DI and GND pin connected, the camera input alarm is triggered, and then camera will execute the action user has set, for example, send snapshot to E-mail address.
If you select "N.C" in "Input sensor setting", when external devise or circuit makes DI and GND pin disconnected, the camera input alarm is triggered, and then camera will execute the action user has set, for example, send snapshot to E-mail address.
GPIO PIN definition
GND (Ground): Initial state is LOW
DO (Digital Output): DC 5V
DI (Digital Input): Max. 50mA, DC 5V
2. GPIO Setting
Event Configuration >> GPIO Setting >> Input Setting
Input Sensor: According to your external device and circuit design, select
N.O (normally open) or N.C (normally closed).
Input Action: When the camera input alarm is triggered, it can trigger the relay out, or send the video to E-mail/ FTP/ SAMBA.
© Copyright 2014 TRENDnet. All Rights Reserved.
TV-IP302PI
Interval: If you select "10 sec" here, once the input alarm is detected and action is triggered, it cannot be triggered again within 10 seconds.
Based on the schedule: When click the option box, only during the selected schedule time the I/O is enabled. That is, for example, the 11th hour of
Monday has not been colored in the schedule table, then no action will be triggered even the camera detects input signal during 11:00~12:00 on
Monday.
Event Configuration >> GPIO Setting >> Output Setting
Mode Setting
On/Off Switch:
When event happens, the camera triggers the external devise and lasts for certain of time according to the event "interval" setting. If it's triggered by motion detection, the triggering time is according to
"interval" setting of motion detection. If it's triggered by external input alarm, the triggering time is according to input "interval" setting. It triggers the external devise and lasts for 10 seconds if you select "10" in interval setting. You can turn off the alarm manually by click "off" at the bottom-right of the live screen page.
Time Switch:
When event happens, the camera triggers the external devise and lasts for certain of time according to the output "interval" setting, and the user is not allowed to break off the alarm manually.
3. Output Test
After the external output hardware is installed, you can use the "Relay Out" button on the live video page to test if DO device works.
On/Off Switch mode:
Click "ON", the camera will trigger the external output devise. For example, your alarm buzzer will continuously ring. You can manually break off the output signal by clicking "OFF".
32
TRENDnet User’s Guide
TV-IP302PI
Factory Default
If you forget your password, please follow the steps to revert back to default value.
1. Remove the power and network cable.
2. Take the included Reset Wire Cable, plug one side of the wire into "Default" and the other side into "GND" on the terminal block as the picture below.
Time Switch mode:
Click "Pulse", the camera will trigger the external output devise for several seconds. The duration length is according to the "interval" setting in Output
Setting.
Event Configuration >> Logs
Click "Logs" to see System Logs, Motion Detection Logs, GPIO Logs and All Logs. If you remove the power from IP camera, Motion Detection Logs will be cleared away.
© Copyright 2014 TRENDnet. All Rights Reserved.
3. Connect power to the camera again. It takes around 30 seconds to boot the camera.
4. Remove the wire and plug in the network cable after the camera finishes booting.
5. If your camera is under a DHCP server, DHCP server will assign an IP automatically. Use IP Installer to find it. If you do not have a DHCP server, the default IP address of camera is 192.168.10.30. Default username is "admin" and password is "admin".
33
TRENDnet User’s Guide
How to Access the IP camera via IP Installer
The IP Installer is an optional utility allow you to search the cameras in your network easily.
1. Insert the Installation CD-ROM into your computer’s CD-ROM drive.
2. Click Exit if the Autorun pop up.
3. Go to Start >> type in D:\\ (D: is the letter assigned to your CD-ROM Drive, and then press the ENTER key on your keyboard .
TV-IP302PI
Search : Search the IP Camera within the Network
Access Camera: access the selected camera’s web page.
Change : change the selected camera’s IP address via Static IP or DHCP.
If Static is selected, you have to manual type in the IP address, Subnet Mask,
Default gateway, DNS 1, DNS 2 and Http Port.
4. Click IPInstaller Folder and click IP Installer.exe
5. The main screen will pop up.
Exit: Exit the IP Installer Utility.
© Copyright 2014 TRENDnet. All Rights Reserved.
34
TRENDnet User’s Guide
How to setup/access the camera behind a Router
You can either setup the Dynamic DNS connection via camera itself or your home router. An account from any of the listed DDNS providers is required prior to this operation.
Configure DDNS on your Camera
1. Go to Camera’s DDNS Setting page, click Enable to activate the feature.
Then select a DDNS provider from the list.
2. Enter your DDNS’s the Host Name, User Name and Password.
TV-IP302PI
4. Open another web browser and go to your Router’s Web Configuration page.
(In the example, TRENDnet’s TEW-651BR Wireless N router is used)
3. In the Port Number section, assign an HTTP port of the camera. The default
HTTP Port on the camera is 80. The example shows above is using port number 9000.
© Copyright 2014 TRENDnet. All Rights Reserved.
35
TRENDnet User’s Guide
5. Go to Virtual Server* section and create a new entry.
Enable: Click Enable
Name: Enter the application name (eg. CameraName)
Protocol: Select TCP
Private Port: The HTTP port that you assign on your Camera.
Public Port: The port used on remote side to access to your Camera.
LAN Server: The local IP address of your Camera.
TV-IP302PI
6. Open another web browser and enter your DDNS domain and camera’s port number. http://yourDomainName:PortNumber
7. Camera’s login page will appear.
Configure DDNS on your router
1. Go to Camera’s DDNS Ports Number section, assign a HTTP port for your camera and click Apply.
Then click Add to add the application.
* Please refer to your router’s user’s manual for detail Virtual Server setting.
Some router might use Port Forwarding or Special applications for this function. The setup steps should be very similar.
2. Login to your router’s web configuration page.
© Copyright 2014 TRENDnet. All Rights Reserved.
36
TRENDnet User’s Guide
3. Find the Dynamic DNS configuration section.
TV-IP302PI
5. Go to Virtual Server* section and create a new entry.
Enable: Click Enable
Name: Enter the application name (eg. Camera Name)
Protocol: Select TCP
Private Port: The HTTP port that you assign on your Camera.
Public Port: The port used on remote side to access to your Camera.
LAN Server: The local IP address of your Camera.
4. Enable DDNS, fill out the following information and then click Apply.
© Copyright 2014 TRENDnet. All Rights Reserved.
Click Add to add the application.
* Please refer to your router’s user’s manual for detail Virtual Server setting.
Some router might use Port Forwarding or Special applications for this function. The setup steps should be very similar.
6. Open another web browser and enter your DDNS domain and camera’s port number. http://yourDomainName:PortNumber
7. The camera login page will appear.
37
TRENDnet User’s Guide
Technical Specifications
Video Features
Lens
Focal Length: 4.2mm, F1.6
Board Lens
Sensor: ¼” Megapixel CMOS sensor
Digital Zoom: 4X
Viewing Angle
Diagonal: 62.9˚
Horizontal: 53.1˚
Vertical : 33.7˚
Minimum Illumination
IR off : 0.5 lux
IR on : 0 lux
15 meters IR illumination distance
Video Codecs / Resolution
H.264: 1280 x 800 up to 30 fps
MPEG4: 1280 x 800 up to 30 fps
JPEG: 1280 x 800 up to 30 fps
Audio
External microphone port
External speaker port
Hardware
Standard
IEEE 802.3u
IEEE 802.3af
© Copyright 2014 TRENDnet. All Rights Reserved.
TV-IP302PI
Device Interface
10/100Mbps PoE port
LED indicator
BNC Port
Microphone Port
Speaker Port
GPIO terminal
Power jack (optional)
Network Protocol
IPv4, IPv6, UDP, TCP/ IP
DHCP client, NTP client, DDNS client, SMTP client, FTP client
SNMP, QoS/DSCP, IEEE 802.1X
Samba, Bonjour
HTTP, HTTPS
PPPoE
UPnP, RTSP, RTP 3GPP
Dimension
Camera : 92 x 62 mm (3.62 x 2.44 in.)
Weight : 450 g (without bracket); 535 g (with bracket)
Operating Temperature
-20 ~ 50°C (-4 ~122°F)
Humidity
Max 90% non-condensing
Power
Input: 100 ~ 24 0 V AC , 1 A, 50~60 Hz
Output: 12 V DC, 1 A external power adapter (for non-PoE installations)
Max consumption : 6.24 W
38
TRENDnet User’s Guide
Warranty
3 years limited
Management Interface
Image Setting
Brightness
Contrast
Hue
Saturation
Sharpness
Auto Gain Control
Shutter Time
Sense-up
Digital WDR
Day & Night light sensor
Flip
Mirror
Rotation 90 degree
Recording
Event based
Motion detection recording to email, FTP, GPIO trigger and Samba
Scheduled recording to email, FTP and Samba
Snapshot
Trigger event (motion detection)
Send alert to email, FTP and / or Samba
Real time s
Management Setting
Maximum 22 user accounts
Supports remote management
© Copyright 2014 TRENDnet. All Rights Reserved.
TV-IP302PI
Compatibility
Internet Explorer 8.0 or higher
Firefox 12.0 or higher
Chrome 19.0 or higher
Safari 4 or higher
Camera Software
TRENDnetVIEW Pro
Supports up to 32 cameras
Multiple language support
Set recording options (motion detection, schedule, event trigger)
Search and playback
Custom viewing modes and options
Compatibility
Windows 7, Vista, XP, Windows Server 2003, 2008
TRENDnetVIEW, Mobile App
View your camera from your portable device
Take snapshots
Zoom in & out
2 way audio
Compatibility
iOS and Android
39
TRENDnet User’s Guide
Troubleshooting
1. I inserted the Utility CD-ROM into my computer's CD-ROM Drive but the
installation menu does not appear automatically. What should I do?
Windows 8
If the installation menu does not appear automatically, press the windows icon and press “r” simultaneously. In the “run” box, type D:\autorun.exe, where “D” in “D:\autorun.exe” is the letter assigned to your CD-ROM Drive, and then press the ENTER key on your keyboard .
Windows 7
If the installation menu does not appear automatically, click on the Windows
Icon on the bottom left hand corner of the screen, click the “Search programs and files” box, and type D:\autorun.exe, where “D” in
“D:\autorun.exe” is the letter assigned to your CD-ROM Drive, and then press the ENTER key on your keyboard .
Windows Vista
If the installation menu does not appear automatically, click Start, click the
Start Search box, and type D:\autorun.exe where "D" in "D:\autorun.exe" is the letter assigned to your CD-ROM Drive, and then press the ENTER key on your keyboard.
Windows XP
If the window does not appear automatically, click Start, click Run and type
D:\autorun.exe where “D” in “D:\autorun.exe” is the letter assigned to your
CD-ROM Drive, and then press the ENTER key on your keyboard.
© Copyright 2014 TRENDnet. All Rights Reserved.
TV-IP302PI
2. The autorun program is unable to detect my camera. What should I do? a. Verify that you have followed all the steps in Section 2: Hardware
Installation. b. Disable any software firewall programs such as ZoneAlarm or Norton
Internet Security. If you are using Windows 8, 7, Vista or XP, disable the built in firewall. c. Reset the IP Camera d. Run the Autorun program from the CD-ROM again.
3. I do not have a DHCP server or DHCP is disabled on my network and I am
unable to configure the TV-IP302PI. What should I do?
a. Go to the TCP/IP settings on your computer and assign a static IP address on your computer’s network adapter in the subnet of
192.168.10.x. Since the default IP address of the TV-IP302PI is
192.168.10.30, do not assign a static IP address of 192.168.10.30 on your computer’s network adapter. b. Open Internet Explorer and enter http://192.168.10.30
into the address bar.
4. The image is blurry. How can I adjust the focus on the IP camera?
The TV-IP302PI is designed to have a clear focus beyond 3 meters. The lens is not adjustable.
5. When I click on Live View the image does not load, what should I do? a. If you are using Internet Explorer, make sure that you install the ActiveX control WEBWATCH.cab.
40
TRENDnet User’s Guide
b. If you are using non-IE browser (Firefox, Chrome, Safari), make sure that you install the plug-in WebPlugin.exe.
6. How do I uninstall the browser’s Active X or Plug-in from my computer?
Click Computer Icon, type in “np_hoem_x.dll” on the top-right corner of the search bar, then click “Search”.
TV-IP302PI
7. I forgot my password. What should I do?
Please follow the steps below to reset to factory default setting a. Remove the power and network cable b. Take the included Reset Wire Cable, plug one side of the wire into
"Default" and the other side into "GND" on the terminal block as shown below.
Delete the file named "np_hoem_x.dll" from search result.
Search for the additional ActiveX or plug-in files listed below and delete them to completely uninstall the ActiveX control or plug-in from your computer.
avcodec-53_v1.8.dll
avutil-51_v1.8.dll
swscale-2_v1.8.dll
WEBWATCH2
WEBWATCH2.ocx
© Copyright 2014 TRENDnet. All Rights Reserved. c. Connect power to the camera again. It takes around 30 seconds to boot the camera. d. Remove the wire and plug in the network cable after the camera finishes booting. e. Run the Install Camera wizard from the CD-ROM to login to the camera.
41
TRENDnet User’s Guide
Limited Warranty
TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase.
TV-IP302PI – 3 Years Limited Warranty
AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty.
If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit’s warranty continues from the original date of purchase. All products that are replaced become the property of
TRENDnet. Replacement products may be new or reconditioned. TRENDnet does not issue refunds or credit. Please contact the point-of-purchase for their return policies.
TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty.
There are no user serviceable parts inside the product. Do not remove or attempt to service the product by any unauthorized service center. This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual.
Warranty service may be obtained by contacting TRENDnet within the applicable warranty period and providing a copy of the dated proof of the purchase. Upon proper submission of required documentation a Return Material Authorization (RMA) number will be issued. An RMA number is required in order to initiate warranty service support for all TRENDnet products. Products that are sent to TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid, insured and packaged appropriately for safe shipment.
Customers shipping from outside of the USA and Canada are responsible for return shipping fees.
Customers shipping from outside of the USA are responsible for custom charges, including but not limited to, duty, tax, and other fees.
WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED
ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL BE, AT TRENDNET’S OPTION, REPAIR OR REPLACE.
THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY
OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO
© Copyright 2014 TRENDnet. All Rights Reserved.
Limited Warranty
ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION
MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.
TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION
DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY
CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING,
UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE
OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES
FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH
THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF
THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR
REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET’S OPTION. THIS DISCLAIMER OF LIABILITY
FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS
ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be governed by the laws of the state of California.
Some TRENDnet products include software code written by third party developers. These codes are subject to the GNU General Public License ("GPL") or GNU Lesser General Public License
("LGPL").
Go to http://www.trendnet.com/gpl or http://www.trendnet.com
Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt
or http://www.gnu.org/licenses/lgpl.txt
for specific terms of each license.
V1.0R /01.10.2014
42
1
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Product Overview
- 3 Package Contents
- 3 Features
- 3 Product Hardware Features
- 4 Application Diagram
- 5 Installation
- 5 Hardware Installation
- 6 Camera Installation
- 9 Configuration
- 9 Viewing Camera Basic Function
- 11 Configuring the Camera Setting
- 12 System
- 14 NETWORK
- 26 AUDIO/VIDEO SETTING
- 30 EVENT CONFIGURATION
- 34 Factory Default
- 35 How to Access the IP camera via IP Installer
- 36 How to setup/access the camera behind a Router
- 39 Technical Specifications
- 41 Troubleshooting