Whelen LCPHOTO Installation Guide
Add to My manuals1 Pages
Whelen LCPHOTO is engineered with versatility in mind. By connecting the RED wire to a fused, ignition controlled +12VDC power source, the BLACK wire to Chassis Ground, and the VIOLET wire to the High/Low Power control wire of the desired device, you can harness its capabilities.
With its compact dimensions, measuring 1.550" x 1.130" x .915", and a mounting hole designed for a #6 Sheet Metal Screw, this device can be seamlessly integrated into various setups. The included gasket enhances the installation process, ensuring a secure and weather-resistant fit.
Once installed, the Whelen LCPHOTO empowers you with precise control over your connected device. Its ability to toggle between High and Low Power modes makes it ideal for tailoring the intensity of your device's output. Whether you seek maximum illumination or prefer a more subdued glow, the LCPHOTO provides the flexibility to adapt to your specific needs.
advertisement
®
Installation Guide:
Model LCPHOTO Photocell
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Internet: www.whelen.com
Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
WARNING: This product can expose you to chemicals including Methylene Chloride which is known to the State of California to cause cancer, and
Bisphenol A, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Mounting and connections...
1.
Place the flange onto the mounting surface and mark the location for the two mounting screws and the wire access hole location as shown.
2.
Drill two mounting holes for the two #6 X 3/8" sheet metal mounting screws and a 3/8” wire access hole. Be sure to thoroughly deburr these holes.
3.
Route the wires through the gasket and the wire access hole and secure the lighthead with the supplied mounting screws. NOTE: Make sure the
Whelen logo on the lens is properly oriented after mounting.
4.
Connect the sensor wires as follows:
RED -
BLACK
VIOLET
-
-
Connect to a fused, ignition controlled +12VDC power source
Connect to Chassis Ground
Connect to the High/Low Power control wire of the desired device
IMPORTANT! Before returning this vehicle to active service, confirm proper operation of this product, as well as all vehicle components/ equipment.
©2017 Whelen Engineering Company Inc.
Form No.14B33 (101917)
1.550"
1.130"
Mounting Hole for
#6 S M
3/8” WIRE
HOLE
S
For warranty information regarding this product, visit www.whelen.com/warranty
®
Installation Guide:
Model LCPHOTO Photocell
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Internet: www.whelen.com
Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
WARNING: This product can expose you to chemicals including Methylene Chloride which is known to the State of California to cause cancer, and
Bisphenol A, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Mounting and connections...
1.
Place the flange onto the mounting surface and mark the location for the two mounting screws and the wire access hole location as shown.
2.
Drill two mounting holes for the two #6 X 3/8" sheet metal mounting screws and a 3/8” wire access hole. Be sure to thoroughly deburr these holes.
3.
Route the wires through the gasket and the wire access hole and secure the lighthead with the supplied mounting screws. NOTE: Make sure the
Whelen logo on the lens is properly oriented after mounting.
4.
Connect the sensor wires as follows:
RED -
BLACK -
VIOLET -
Connect to a fused, ignition controlled +12VDC power source
Connect to Chassis Ground
Connect to the High/Low Power control wire of the desired device
IMPORTANT! Before returning this vehicle to active service, confirm proper operation of this product, as well as all vehicle components/ equipment.
©2017 Whelen Engineering Company Inc.
Form No.14B33 (101917)
1.550"
1.130"
Mounting Hole for
#6 S M S
3/8” WIRE
HOLE
Page 1 www.whelen.com/warranty
advertisement
Related manuals
advertisement