Manual

Add to my manuals
10 Pages

advertisement

Manual | Manualzz

Mini Digital Multimeter

Model MN15

User's Guide

Introduction

Congratulations on your purchase of the Extech MN15 MultiMeter. The MN15 offers AC/DC Voltage,

AC/DC Current, Resistance, Diode, and Continuity testing plus Type K thermocouple temperature measurements. Proper use and care of this meter will provide many years of reliable service.

Safety

WARNING

CAUTION

MAX

600V

This symbol adjacent to another symbol, terminal or operating device indicates that the operator must refer to an explanation in the Operating Instructions to avoid personal injury or damage to the meter.

This WARNING symbol indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury.

This CAUTION symbol indicates a potentially hazardous situation, which if not avoided, may result damage to the product.

This symbol advises the user that the terminal(s) so marked must not be connected to a circuit point at which the voltage with respect to earth ground exceeds 600V.

This symbol adjacent to one or more terminals identifies them as being associated with ranges that may, in normal use, be subjected to particularly hazardous voltages. For maximum safety, the meter and its test leads should not be handled when these terminals are energized.

This symbol indicates that a device is protected throughout by double insulation or reinforced insulation.

 Improper use of this meter can cause damage, shock, injury or death. Read and understand this user manual before operating the meter.

 Always remove the test leads before replacing the battery or fuses.

 Inspect the condition of the test leads and the meter itself for any damage before operating the meter. Repair or replace any damage before use.

 Use great care when making measurements if the voltages are greater than 25VAC rms or

35VDC. These voltages are considered a shock hazard.

 Always discharge capacitors and remove power from the device under test before performing Diode, Resistance or Continuity tests.

 Voltage checks on electrical outlets can be difficult and misleading because of the uncertainty of connection to the recessed electrical contacts. Other means should be used to ensure that the terminals are not "live".

 If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

 Disposal: Follow all legal stipulations regarding disposal of this device at the end of its lifecycle

 This device is not a toy and is not intended for children. It contains hazardous objects as well as small parts that the children could swallow. Should a child swallow any part, contact a physician immediately.

 Do not leave batteries or packing material lying around, they can be dangerous for children if they use them as toys.

 In the device is going to be unused for an extended period of time, remove the batteries.

 Expired or damaged batteries can cause cauterization on contact with skin. Always, use gloves when handling damaged batteries.

 See that the batteries are not short-circuited. Do not throw batteries into fire.

2 MN15-en-GB_V1.3 4/15

VDC or VAC

VDC or VAC 200mV range mA AC/DC

A AC/DC

Resistance, Continuity

Controls and Jacks

Input Protection Limits

600VAC and VDC

200Vrms

200mA 250V fast acting fuse

10A 250V fast acting fuse

(for 30 seconds max. every 15 minutes.)

250Vrms for 15 sec. max.

°F

2. Rotary function switch

3. 10 ampere test lead jack

4. Test lead jack for voltage, milliamp, resistance/continuity, diode and temperature functions

5. COM test lead jack

6. Battery compartment (rear)

SYMBOLS

•))) Continuity

AC

A Amps

Degrees Fahrenheit

DC m milli (10 -3 ) (volts, amps)

V



Diode

Volts

Ohms

°C

Low battery indicator

3 MN15-en-GB_V1.3 4/15

Operating Instructions

WARNING: Risk of electrocution. High-voltage circuits, both AC and DC, are very dangerous and should be measured with great care.

NOTE: On some low AC and DC voltage ranges, with the test leads not connected to a device, the display may show a random, changing reading. This is normal and is caused by the high-input sensitivity. The reading will stabilize and give a proper measurement when connected to a circuit.

AC VOLTAGE MEASUREMENTS

WARNING: Risk of Electrocution. The probe tips may not be long enough to contact the live parts inside some 240V outlets for appliances because the contacts are recessed deep in the outlets. As a result, the reading may show 0 volts when the outlet actually has voltage on it. Make sure the probe tips are touching the metal contacts inside the outlet before assuming that no voltage is present.

CAUTION: Do not measure AC voltages if a motor on the circuit is being switched ON or OFF.

Large voltage surges may occur that can damage the meter.

1. Set the function switch to the 600 VAC position.

2. Insert the black test lead banana plug into the negative COM jack.

Insert red test lead banana plug into the positive V jack.

3. Touch the black test probe tip to the neutral side of the circuit.

4. Touch the red test probe tip to the “hot” side of circuit.

5. Read the voltage in the display.

6. If the reading is less than 200V, switch to the 200V range to improve resolution.

DC VOLTAGE MEASUREMENTS

CAUTION: Do not measure DC voltages if a motor on the circuit is being switched ON or OFF.

Large voltage surges may occur that can damage the meter.

1. Set the function switch to the highest 600VDC position.

2. Insert the black test lead banana plug into the negative COM jack.

Insert the red test lead banana plug into the positive V jack.

3. Touch the black test probe tip to the negative side of the circuit. Touch the red test probe tip to the positive side of the circuit.

4. Read the voltage in the display.

5. If the reading is less than the maximum of a lower range, switch to that range to improve resolution.

4 MN15-en-GB_V1.3 4/15

DC CURRENT MEASUREMENTS

CAUTION: Do not make current measurements at 10 Amps for longer than 30 seconds. Exceeding

30 seconds may cause damage to the meter and/or the test leads.

1. Insert the black test lead banana plug into the negative COM jack.

2. For current measurements up to 200mA, set the function switch to the 200mA position and insert the red test lead banana plug into the

mA jack.

3. For current measurements up to 10A, set the function switch to the

10A position and insert the red test lead banana plug into the 10A jack.

4. Remove power from the circuit under test, then open up the circuit at the point where you wish to measure current.

5. Touch the black test probe tip to the negative side of the circuit. Touch the red test probe tip to the positive side of the circuit.

6. Apply power to the circuit.

7. Read the current in the display.

5 MN15-en-GB_V1.3 4/15

RESISTANCE MEASUREMENTS

WARNING: To avoid electric shock, disconnect power to the unit under test and discharge all capacitors before taking any resistance measurements.

1. Set the function switch to the highest  position.

2. Insert the black test lead banana plug into the negative COM jack.

Insert the red test lead banana plug into the positive  jack.

3. Touch the test probe tips across the circuit or part under test.

4. Read the resistance in the display. Move the function switch to successively lower  ranges to obtain a higher resolution reading.

CONTINUITY CHECK

WARNING: To avoid electric shock, never measure continuity on circuits that have a voltage potential.

1. Set the function switch to the position.

2. Insert the black lead banana plug into the negative COM jack.

Insert the red test lead banana plug into the positive  jack.

3. Touch the test probe tips to the circuit or wire you wish to check.

4. If the resistance is less than approximately 100 , the audible signal will sound. If the circuit is open, the display will indicate “1. ”.

DIODE TEST

1. Set the function switch to the position.

2. Insert the black test lead banana plug into the negative COM jack

Insert the red test lead banana plug into the positive jack.

3. Touch the test probes to the diode under test.

4. A typical diode will indicate approximately .400 to .500 volts for the forward test and “1. ” for the reverse test.

5. A shorted diode will indicate a low value in both the reverse and forward test directions. An open diode will indicate “1. ” in both test directions.

6 MN15-en-GB_V1.3 4/15

BATTERY VOLTAGE TEST

CAUTION: Do not measure batteries while they are installed in the devices they are powering. The batteries must be removed from installations before tests can be made.

1. Set the function switch to the 1.5V or 9V BAT switch position. Use the

1.5V position for ‘AAA’, ‘AA’, ‘C’, ‘D’, and other 1.5V batteries. Use the

9V position for square 9V transistor batteries.

2. Insert the black test lead banana plug into the negative COM jack.

Insert the red test lead banana plug into the positive V jack.

3. Touch the black test probe tip to the negative side of the battery.

Touch the red test probe tip to the positive side of the battery.

4. Read the voltage in the display.

TEMPERATURE MEASUREMENTS

1. Set the function switch to the °F or °C position.

2. Insert the Temperature Probe into the COM and Temp jacks, making sure to observe the correct polarity.

3. Touch the Temperature Probe head to the part to be measured. Keep the probe touching the part under test until the reading stabilizes.

4. Read the temperature in the display.

Note: The temperature probe is fitted with a type K mini connector.

A mini connector to banana connector adaptor is supplied for connection to the input banana jacks.

7 MN15-en-GB_V1.3 4/15

Maintenance

WARNING: To avoid electric shock, disconnect the test leads from any source of voltage before removing the back cover or the battery or fuse covers.

WARNING: To avoid electric shock, do not operate your meter until the battery and fuse covers are in place and fastened securely.

This MultiMeter is designed to provide years of dependable service, if the following care instructions are performed:

1. KEEP THE METER DRY. If it gets wet, wipe it off.

2. USE AND STORE THE METER IN NORMAL TEMPERATURES. Temperature extremes can shorten the life of the electronic parts and distort or melt plastic parts.

3. HANDLE THE METER GENTLY AND CAREFULLY. Dropping it can damage the electronic parts or the case.

4. KEEP THE METER CLEAN. Wipe the case occasionally with a damp cloth. DO NOT use chemicals, cleaning solvents, or detergents.

5. USE ONLY FRESH BATTERIES OF THE RECOMMENDED SIZE AND TYPE. Remove old or weak batteries so they do not leak and damage the unit.

6. IF THE METER IS TO BE STORED FOR A LONG PERIOD OF TIME, the battery should be removed to prevent damage to the unit.

BATTERY/FUSE INSTALLATION and LOW BATTERY INDICATION

WARNING: To avoid electric shock, disconnect the test leads from any source of voltage before removing the battery cover. Do not operate meter unless the battery is in place.

LOW BATTERY INDICATION

The icon will appear in the display when the battery voltage becomes low. Replace the battery when this appears.

BATTERY REPLACEMENT

1. Disconnect the test leads from the meter.

2. Remove the 2 Phillips head screws located on the back of the instrument and remove the battery cover.

3. Replace the 9V battery.

4. Secure the fuse/battery compartment cover.

5. Dispose of the old battery as required by local regulations.

Never dispose of used batteries or rechargeable batteries in household waste. 

As consumers, users are legally required to take used batteries to appropriate  collection sites, the retail store where the batteries were purchased, or wherever  batteries are sold. 

Disposal: Do not dispose of this instrument in household waste. The user is obligated to take end‐

of‐life  devices  to  a  designated  collection  point  for  the  disposal  of  electrical  and  electronic  equipment.  

 

Other Battery Safety Reminders 

o Never dispose of batteries in a fire. Batteries may explode or leak.  o Never mix battery types. Always install new batteries of the same type. 

8 MN15-en-GB_V1.3 4/15

FUSE REPLACEMENT

1. Disconnect the test leads from the meter.

2. Remove the 2 Phillips head screws located on the back of the instrument and remove the battery cover.

3. Gently remove the fuse(s) and install the new fuse(s) into the holder(s).

4. Always use fuses of the proper size and value (200mA/660V ceramic fast blow for the mA / µA ranges, 10A/250V ceramic fast blow for the A range).

5. Secure the fuse/battery compartment cover.

WARNING: To avoid electric shock, do not operate your meter until the fuse cover is in place and fastened securely.

Range Specifications

Function Range Accuracy

200mV 0.1mV

DC Voltage

(V DC)

AC Voltage

(V AC)

DC Current

(A DC)

20V 0.01V

200V 0.1V

600V 1V

600V 1V

200mA 100 A

(1.2% reading + 10 digits

(50/60Hz)

(1.2% reading + 2 digits)

Resistance

200  0.1

2000  1 

20k  0.01k

200k  0.1k

20M  10k

(0.8% reading + 2 digits)

(1.5% reading + 2 digits)

Battery Test

Temperature

-20°C to 750°C

-4°F to 1400°F

Notes:

Accuracy specifications consist of two elements:

1°C

1°F

(3% of reading +5°C/9°F)

 (% reading) – This is the accuracy of the measurement circuit.

 (+ digits) – This is the accuracy of the analog to digital converter.

Accuracy is stated at 18 o C to 28 o C (65 o F to 83 o F) and less than 75% RH.

9 MN15-en-GB_V1.3 4/15

General Specifications

Diode Test

Continuity Check

Bias voltage: 2.8VDC typical

Audible signal will sound if the resistance is less than 100 

Input Impedance 1MΩ (VDC & VAC)

AC Bandwidth

Display

50 / 60Hz

2000 count (0 to 1999) LCD

Overrange indication

Polarity

Measurement Rate

“1___” is displayed

Automatic (no indication for positive); Minus (-) sign for negative

2 times per second, nominal

Low Battery Indication

Battery

Fuses

Operating Temperature

Operating Humidity

Storage Humidity

Operating Altitude

Weight

Size

is displayed

One (1) 9V battery (NEDA 1604) mA range; 200mA/660V ceramic fast blow

A range; 10A/250V ceramic fast blow

0ºC to 50ºC (32ºF to 122ºF)

C to 60 o C (-4 o F to 140 o F)

Max 70% up to 31ºC (87ºF) decreasing linearly to 50% at 50ºC (122ºF)

< 80% RH

2000 meters. (7000 ft) maximum.

255g (9.17 oz)

132 x 66 x 38mm (5.2” x 2.6” x 1.5”)

Approvals

Safety

CE

This meter is intended for indoor use and protected, against the users, by double insulation per EN61010-1 and IEC61010-1 2nd Edition

(2001) to CAT II 1000V & CAT III 600V; Pollution Degree 2.

PER IEC1010 OVERVOLTAGE INSTALLATION CATEGORY

OVERVOLTAGE CATEGORY I

Equipment of OVERVOLTAGE CATEGORY I is equipment for connection to circuits in which measures are taken to limit the transient overvoltages to an appropriate low level. Note – Examples include protected electronic circuits.

OVERVOLTAGE CATEGORY II

Equipment of OVERVOLTAGE CATEGORY II is energy-consuming equipment to be supplied from the fixed installation.

Note – Examples include household, office, and laboratory appliances.

OVERVOLTAGE CATEGORY III

Equipment of OVERVOLTAGE CATEGORY III is equipment in fixed installations.

Note – Examples include switches in the fixed installation and some equipment for industrial use with permanent connection to the fixed installation.

OVERVOLTAGE CATEGORY IV

Equipment of OVERVOLTAGE CATEGORY IV is for use at the origin of the installation.

Note – Examples include electricity meters and primary over-current protection equipment

Copyright © 2008‐2015 FLIR Systems, Inc. 

All rights reserved including the right of reproduction in whole or in part in any form 

ISO‐9001 Certified 

www.extech.com 

10 MN15-en-GB_V1.3 4/15

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement