User`s Manual

Add to my manuals
17 Pages

advertisement

User`s Manual | Manualzz

E31

1MP Bullet with D/N, IR, Basic WDR,

Fixed lens

Hardware User’s Manual

(PoE)

Ver. 2012/11/29

E31 Hardware User’s Manual

Table of Contents

0.

Precautions 3

1.

Introduction 4

Package Contents ........................................................................... 4

Features and Benefits ..................................................................... 5

Safety Instructions .......................................................................... 6

Physical description ........................................................................ 8

How to Do the Waterproof with Conduit Installation ................... 9

Basic Connections ......................................................................... 12

Product Specification .................................................................... 13

2.

Accessing Camera 14

If you have DHCP server / router in your network: ...................... 14

If you do

NOT have DHCP server / router in your network: ......... 14

2 www.acti.com

E31 Hardware User’s Manual

0. Precautions

Read these instructions

You should read all the safety and operating instructions before using this product.

Heed all warnings

You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.

Servicing

Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Trademarks

All names used in this manual are probably registered trademarks of respective companies.

Liability

Every reasonable care has been taken during the writing of this manual. Please inform your local office if you find any inaccuracies or omissions. We cannot be held responsible for any typographical or technical errors and reserve the right to make changes to the product and manuals without prior notice.

FCC/CE Regulation

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the users will be required to correct the interference at their own expense.

3 www.acti.com

E31 Hardware User’s Manual

1. Introduction

Package Contents

E31 (Included camera stand/sun shield)

Conduit Gland

Accessories

Lens Focus Tuner

Warranty Card QIG

4 www.acti.com

E31 Hardware User’s Manual

Features and Benefits

This is a cutting-edge digital video surveillance camera. It can compress and transmit real time images with outstanding image quality through a standard TCP/IP network. This camera is your best choice to build an intelligent IP surveillance system.

H.264 High Profile/MJPEG Multi-Codec Dual Streaming

This device supports 2 compression formats, H.264 High Profile and MJPEG. It brings superior image quality at 30 frames per second up to a resolution of 720p (1280 x 720) pixels and VGA

(640 x 480) pixels.

Built-in Hardware Motion Detection

No more external motion sensors are required. You may assign up to 3 video motion detection areas. By tuning the object size and sensitivity, it will reliably detect objects passing though is view. Hardware motion detection also offers better sensitivity and faster response time than software motion detection.

Powerful Bundled Surveillance Software

To extend the capabilities of the IP Camera series, a powerful surveillance program is included in the package for free. Users can easily use an existing PC as a digital video recorder.

Scheduled recording and manual recording keep every important video recorded in the local hard disk. Reliable and accurate motion detection with instant warning enables immediate response in every condition. Quick and simple search and playback function lets you easily find the images and video you want.

Software Development Kit Support

This IP Camera can be integrated or controlled by applications from third party software developers. Software developers can save considerable efforts by using our Streaming Library or ActiveX control. Please contact us for details on integration support.

5 www.acti.com

E31 Hardware User’s Manual

Safety Instructions

Don’t open the housing of the product

Cleaning

Disconnect this video product from the power supply before cleaning.

Attachments

Do not use attachments not recommended by the video product manufacturer as they may cause hazards.

Water and Moisture

Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.

Don’t use accessories not recommended by the manufacturer

Only install this device in a dry place protected from weather

Servicing

Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Damage Requiring service

Disconnect this video product from the power supply immediately and refer servicing to qualified service personnel under the following conditions.

1) When the power-supply cord or plug is damaged

2) If liquid has been spilled, or objects have fallen into the video product.

3) If the video product has been directly exposed to rain or water.

4) If the video product does not operate normally by following the operating Instructions in this manual. Adjust only those controls that are covered by the instruction manual, as an improper adjustment of other controls may result in damage, and will often require extensive work by a qualified technician to restore the video product to its normal operation.

6 www.acti.com

E31 Hardware User’s Manual

Safety Check

Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition.

7 www.acti.com

E31 Hardware User’s Manual

Physical description

1) Reset Button

Step 1: Press and continue to hold the Reset Button for 15 seconds (with a sharp tipped object, like a pen.) after the unit has successfully completed the boot process.

Step 2: The Ethernet LED light will turn off for about 1~2 seconds and flash on for another second. By this time the reset to default operation is already completed. You may then release the reset button. This length of time fluctuates slightly with the environment. The unit will come back on and stay on after a few more seconds. The unit will start up with factory default settings automatically.

2) Power LED

LED light will light up while the power is on. LED light will light off after the unit has successfully completed the boot process.

3) Ethernet Port

The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this

IP device can auto detect the speed of local network segment (10Base-T/100Base-TX

Ethernet).

8 www.acti.com

E31 Hardware User’s Manual

How to Do the Waterproof with Conduit Installation

Beside the bundled network cable, you also can use conduit and follow the installation procedure to make the camera be water-resistant even for the situations where the camera can easily be flooded by pouring rain.

The important part to focus on during the installation:

The protection of the cabling has to be done by a proper flex conduit. The size of the flex conduit that matches with the conduit gland is 1/2

. Please note that the conduit gland is

included to the package of the bullet camera.

The following images show the step-by-step procedure of completing the water-proof installation.

Disassemble the conduit gland as shown on the photo.

1. Pull the network cable through the flex conduit.

Please note that the size of the conduit and the gland is big enough to let the RJ-45 connector pass through all the way.

2. Two pieces from the conduit gland set will be attached to flex conduit first.

3. Remove the bundled network cable and connector from back side cover of the camera.

9 www.acti.com

E31 Hardware User’s Manual

4. The third piece of conduit gland goes through the back side cover of the camera.

5. The fourth piece (locking nut) is used to lock the gland firmly from the inside of the back side cover.

6. Pull the network cable through the back side cover of the camera.

7. Connect the flex conduit to the back side cover of the camera.

10 www.acti.com

E31 Hardware User’s Manual

8. Tighten the domed sealing nut.

9. Plug the network cable into the camera

’s RJ-45 connector before closing the back side of the camera. If you are not using PoE and need an additional power cord then please connect it at this stage, too.

10. Tighten the screws of the back side of the camera properly.

11. Finally, the bullet camera with properly mounted flex conduit as well as with proper outdoor bracket would look like this. The camera is now ready to withstand even the most severe rain storms.

11 www.acti.com

E31 Hardware User’s Manual

Basic Connections

Follow the procedures below to connect the IP device to the respective apparatuses.

Please use a PoE (Power over Ethernet) supported switch or injector:

1) Connect your IP Camera to the PoE Switch / Injector by CAT5 or CAT6 cables with RJ45 connector.

2) Connect your PoE Switch / Injector to PC with another CAT5 / CAT6 network cable.

12 www.acti.com

E31 Hardware User’s Manual

Product Specification

• Device

Device Type

Image Sensor

Day / Night

Minimum Illumination

Color to B/W switch

Mechanical IR Cut Filter

IR Sensitivity Range

IR LED

IR Working Distance

Electronic Shutter

• Lens

Focal Length / Aperture

Iris

Focus

Mount Type

Horizontal Viewing Angle

• Video

Compression

Maximum Frame Rate vs. Resolution

Multi-Streaming

Bit Rate

Bit Rate Mode

Image Enhancement

Privacy Mask

Text Overlay

Image Orientation

• Network

Protocol & Service

Ethernet Port

Security

• Alarm

Alarm Trigger

Alarm Response

• General

Power Source / Consumption

Mount Type

Weight

Dimensions (Φ x H)

Bundled Accessories

Environmental Casing

Operating Temperature

Operating Humidity

Approvals

• Integration

Unified Solution

ISV Integration

Firmware Access Browser

E31

Bullet Camera

Progressive Scan CMOS

Yes

Color: 0.1 lux at F1.8 (30 IRE, 2400°K); B/W: 0 lux (IR LED on)

ISP sensor based switch; Configurable

Yes

700 - 1100 nm

IR LED x 20 (850 nm)

15 m (0 lux, 30 IRE, Max Exposure Gain)

1/5~1/2000 sec (manual/ auto mode)

Fixed focal, f4.2 mm / F1.8

Fixed iris

Fixed focus

Board Mount

55.9°

H.264 HP, MJPEG

30 fps at 1280 x 720 (HD 720p); 30 fps at 640 x 480 (VGA)

Simultaneous dual streams based on two configurations

28 Kbps - 6 Mbps (per stream)

Constant, Variable

Basic WDR; White balance: automatic, hold, and manual;

Brightness; Contrast; Automatic gain control; Digital noise reduction; Flickerless

4 configurable regions

User defined text on video

Image flip and mirror

TCP, UDP, HTTP, HTTPS, DHCP, PPPoE, RTP, RTSP, IPv6, DNS, DDNS, NTP, ICMP, ARP, IGMP, SMTP, FTP,

UPnP, SNMP, Bonjour

1, Ethernet (10/100 Base-T), RJ-45 connector

IP address filtering; HTTPS encryption; Password protected user levels; IEEE 802.1X network access control

Video motion detection (3 regions)

Notify control center; Change camera settings; Command other devices;

E-mail notification with snapshots; Upload video, snapshot to FTP server

PoE Class 2 (IEEE802.3af) / 5.41 W (IR on)

Wall, Ceiling, Corner, Pole

584 g (1.29 lb)

77 mm x 196.74 mm (3.04" x 7.7'')

Bracket

Weatherproof (IP66 rated)

-20 °C ~ 50 °C (-4 °F ~ 122 °F)

10% ~ 85% RH

CE, FCC, IP66

Fully compatible with ACTi software

Software Development Kit (SDK) available; ONVIF compliant

Microsoft Internet Explorer 6.0 or newer

13 www.acti.com

E31 Hardware User’s Manual

2. Accessing Camera

If you have DHCP server / router in your network:

Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Camera into the network and your IP device will acquire network address by itself. Find and access the device with our IP

Utility program. You may download it at:

http://www.acti.com/product/detail/Software/ACTi_Utility_Suite

If you do network:

NOT

have DHCP server / router in your

1. Configure your PC to use the same subnet by changing your PC’s IP address to the subnet with prefix 192.168.0.XXX. The last number should be anything from 1 to 254 except 100 and other occupied IP addresses. Subnet mask should be 255.555.255.0.

2. The default IP used by this device is 192.168.0.100. Please make sure your PC is

NOT using this address and that no two equipments use the same IP address in the network.

3. Change your IP address by going to Control Panel ->Manage Network Connections ->

Right click on the connection to change -> Option -> TCP/IP IPv4 Properties.

14 www.acti.com

E31 Hardware User’s Manual

Please set the settings as below.

IP address: 192.168. 0.xxx

Subnet mask: 255.255.255.

0

(NOTE: xxx should be a number from 1 to 254 except 100, which is used by the IP device. Please also make sure that no two equipments use the same IP address in the same network..)

4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP:

192.168.0.100

5. When you see the login window, please input default user and password:

Default User: Admin Password: 123456

15 www.acti.com

E31 Hardware User’s Manual

6. After logging in, you will see the video from camera. To go to the main menu, click the

“Setup” button on the top left.

If you are using a single camera, this is enough to access the device.

If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps.

7. Go to IP Settings -> Connection Type

8. Change the IP mode to Static.

9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC

’s IP address or 192.168.0.100.). If this is not the first device you add to the network, please also avoid other devices

’ IPs.

16 www.acti.com

E31 Hardware User’s Manual

10. Click

“Apply”

11. Please go to System -> Save & Reboot, and click

“Apply”. Internet Explorer will close after a few seconds. This is normal.

12. Wait for 30 seconds, and open IE again to connect to the

new IP

. (In this example,

192.168.0.101). For the second device or more you add into the network, please type the correct IP.

13. Adjust the default Video setting by going to Video -> Video

Please refer the firmware manual for the detail information.

17 www.acti.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals