Symmons S-3504-H321-V-CYL-B1.5TRM Dia Single Handle 1-Spray Tub and Hand Shower Trim Specification
Add to My manuals2 Pages
advertisement
Location:
Dia
®
S-3504-H321-V-CYL-B
Tub/Hand Shower System
Specification Submittal
Feature Highlights Options/Modifications cont.
• Secondary integral diverter
• Metal lever handle
• Adjustable stop screw to limit handle turn
• 7" non-diverter tub spout
• 30" slide bar for hand shower
• 60" flexible metal hose
• 1 mode hand shower
• Dual checks for backflow protection
• 2.5 gpm (9.5 L/min) standard flow restrictor
• Components shall be metal and nonmetallic construction, plated in standard polished chrome finish
• For optional in-line vacuum breaker order p/n EF-109
Model Numbers
☐ S-3504-H321-V-CYL-B
Tub/Hand Shower System with Symmons
Temptrol® 4-port pressure balancing mixing valve
☐ S-46-2-BODY
Symmons Temptrol 4-port pressure balancing mixing valve
☐ S-46-2X-BODY
Symmons Temptrol 4-port pressure balancing mixing valve with integral service stops
Options/Modifications
☐ -REV Reverse coring, hot on right, cold on left, for back to back installations
☐ -SS
☐ -T4
☐ -T724
☐ -T736
☐ -T748
☐ -TRM
☐ -VB
☐ -VP
Slip spout (available in chrome and STN finish only)
Alternative 361TS, non-diverter square tub spout
24" slide bar/grab bar with ADA hand shower
36" slide bar/grab bar with ADA hand shower
48" slide bar/grab bar with ADA hand shower
Trim only, valve must be ordered separately
Elevated vacuum breaker
Vandal resistant escutcheon screws in place of standard screws
☐ -X Integral service stops - allows water shutoff at valve for service
☐ -X-CHKS Integral check stops - for use in installations where a positive shut-off device is used downstream of mixing valve
☐ -BBZ Brushed Bronze finish (not available with H35 or
T7 series slide bar/grab bar modifications)
☐ -MB Matte Black finish (not available with H35 or T7 series slide bar/grab bar modifications)
☐ -STN Satin Nickel finish
Note: Append appropriate -suffix to model number.
☐ -1.5
☐ -2.0
CG 1.5 gpm (5.7 L/min) flow restrictor
2.0 gpm (7.6 L/min) flow restrictor
☐ -72 72" hose in place of 60" hose
☐ -ADACHS ADA hand shower wand (chrome)
☐ -ADAHS ADA hand shower wand (white)
☐ Delete
Suffix B
Chrome only plastic escutcheon on valve with color graphics/indicators
☐ -H323-V 3 mode hand shower unit with slide bar
☐ -H323-V-48 3 mode hand shower unit with 48" slide bar
☐ -H3524 24" decorative slide/grab bar with ADA hand shower
☐ -H3536 36" decorative slide/grab bar with ADA hand shower
☐ -IPS
☐ -L/HS
☐ -QD
☐ -R
☐ -REB
1/2" female IPS connections
Less hand shower
Quick-disconnect on hand spray units
60" white vinyl hose in place of 60" metal hose
Rebuild trim kit, includes TA-10 and TA-4
Compliance
- ASME A112.18.1/CSA B125.1
Warranty
Limited Lifetime - to the original end purchaser in consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete warranty information.
Dimensions
-T4
II
EE
JJ
FF
LL
C
D
E
F
G
H
I
J
A
B
K
L
M
N
O
P
Q
Measurements
6", 152 mm
Male 1/2-14 NPT thread must be recessed 1/4" (6 mm) from finished wall
Ø 7-1/2", 191 mm
3-1/2", 89 mm
Ref. 32", 813 mm
3", 76 mm
2-7/8", 73 mm
Rough-in
2-3/8" ± 1/2", 60 mm ± 13 mm
Ø 2-1/2", 64 mm
Ref. 12", 305 mm
Male 1/2-14 NPT fitting must protrude 5-1/4" (133 mm) from finished wall
5-1/4", 133 mm
7", 178 mm
2-1/4", 57 mm
2-1/2", 64 mm
5-5/8", 143 mm
Male 1/2-14 NPT fitting must protrude 4-7/16" (113 mm) from finished wall
Notes:
1) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater.
2) Do not install positive shut-off device/devices that do not allow the valve to flow at least 1.5 gpm to valve outlets.
3) All dimensions measured from nominal rough-in (see H as reference).
4) Dimensions subject to change without notice.
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
Copyright © 2018 Symmons Industries, Inc. ■ symmons.com ■ [email protected] ■ ZV-1542 REV F ■ 121218
advertisement
Related manuals
advertisement