ELATION ARENA PAR ZOOM - USER MANUAL 1.2

ARENA PAR ZOOM™

user manual 1.2

w w w . e l a t i o n l i g h t i n g . c o m

©2013 ELATION PROFESSIONAL all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL.

Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-‐ELATION brands and product names are trademarks or registered trademarks of their respective companies.

ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product.

Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040

323-582-3322 | 323-832-9142 fax | www.elationlighting.com | [email protected]

Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, Netherlands

+31 45 546 85 66 | +31 45 546 85 96 fax | www.elationlighting.eu | [email protected]

2

ARENA PAR ZOOM

™

User Manual 1.0

C O N T E N T S

General Information

Warranty

Safety Instructions

General Guidelines

Fixture Overview

Installation

Understanding DMX

Fixture Menu

DMX Channel Functions And Values

Trouble Shooting

Cleaning and Maintenance

Technical Specifications

Optional Accessories

Declaration Of Conformity


9

10

12

16

21

22

23

24

28

29

4

6

7

8

3

ARENA PAR ZOOM

™

User Manual 1.0


G E N E R A L I N F O R M A T I O N

INTRODUCTION

Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The ARENA PAR ZOOM

™

has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance.

UNPACKING

Thank you for purchasing the ARENA PAR ZOOM

™

by Elation Professional®. Every

ARENA PAR ZOOM

™

has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your unit for damage and be sure all accessories necessary to operate the unit have arrived intact. In the event damage has been found or parts are missing, please contact our customer support team for further instructions. Please do not return this unit to your dealer without first contacting customer support at the number listed below. Please do not discard the shipping carton in the trash. Please recycle whenever possible.

BOX CONTENTS

• (1) Power Cable

• Manual & Warranty Card

M A N U A L U P D A T E S

Please check

www.elationlighting.com

for the latest revision/update of this manual.

4

ARENA PAR ZOOM

™

User Manual 1.0


CUSTOMER SUPPORT

Elation Professional

®

provides a customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.elationlighting.com

for any comments or suggestions. For service related issue please contact Elation

Professional®. Service Hours are Monday through Friday 8:00 a.m. to 5:00 p.m. PST.

Voice: 323-582-3322 Fax: 323-832-9142

E-mail: [email protected]

Forum: www.ElationLighting.com/forum

WARRANTY REGISTRATION

The ARENA PAR ZOOM

™

carries a two-year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization

(R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items returned without a R.A. number clearly marked on the outside of the package will be refused and returned at customer’s expense. You may obtain a R.A. number by contacting customer support at 323-582-3322.

I M P O R T A N T N O T I C E !

There are no user serviceable parts inside this unit. Do not attempt any repairs yourself; doing so will void your manufactures warranty. Damages resulting from modifications to this fixture and/or the disregard of safety and general user instructions found in this user manual void the manufactures warranty and are not subject to any warranty claims and/or repairs.

5

ARENA PAR ZOOM

™

User Manual 1.0


2 - Y E A R L I M I T E D W A R R A N T Y

A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.

B. For warranty service, send the product only to the Elation Professional® factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, Elation Professional® will pay return shipping charges only to a designated point within the United

States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are shipped with the product, Elation Professional® shall have no liability what so ever for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which Elation Professional® concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Elation Professional® factory unless prior written authorization was issued to purchaser by Elation Professional®; if the product is damaged because not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check-up. During the period specified above, Elation Professional® will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of Elation Professional® under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Elation Professional®. All products covered by this warranty were manufactured after January 1, 1990, and bare identifying marks to that effect.

E. Elation Professional® reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by

Elation Professional® in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professional® be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.

G. This warranty is the only written warranty applicable to Elation Professional® Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

6

ARENA PAR ZOOM

™

User Manual 1.0


S A F E T Y I N S T R U C T I O N S

The ARENA PAR ZOOM

™

is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow the guidelines in this manual. The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual.

This device falls under PROTECTION CLASS 1. It’s essential this device is grounded properly, and only qualified personnel perform all electrical connections.

•

For proper operation, follow the Installation guidelines described on page 10 of this manual. Only qualified and certified personnel should perform installation of this fixture and only the original rigging parts

(brackets) included with this fixture should be used for installation. Any modifications will void the original manufactures warranty and increase the risk of damage and/or personal injury.

•

Never look directly into the light source of this fixture to prevent risk of injury to your retina, which may induce blindness. Those suffering from EPILEPSY should avoid looking directly into the light source of this unit at all times.

•

The fan and air inlets must remain clean and never blocked. Allow approx. 6” (15cm) between this fixture and other devices or a wall for proper cooling.

•

Always disconnect from main power source before performing any type of service and/or cleaning procedure. Only handle the power cord by the plug end, never pull out the plug by tugging the wire portion of the cord.

•

Do not operate this fixture if the power cord has become frayed, crimped and/or damaged. If the power cord is damaged, replace it immediately with a new one of similar power rating.

7

ARENA PAR ZOOM

™

User Manual 1.0


G E N E R A L G U I D E L I N E S

• N E V E R O P E N T H I S F I X T U R E W H I L E I N U S E !

• During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture. This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and will decrease gradually over time.

• This fixture is a professional lighting effect designed for INDOOR / DRY LOCATIONS

ONLY on stage, in nightclubs, theatres, etc.

• Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while operating, to prevent any fire hazard.

• The fixture must be installed in a location with adequate ventilation, at least 1.5 feet

(.5m) from adjacent surfaces. Be sure no air ventilation slots are blocked.

• Do not attempt installation and/or operation without proper knowledge how to do so.

• Do not permit operation by persons who are not qualified for operating this type of theatrical fixture. Most damages are the result of operations by nonprofessionals.

• Consistent operational breaks may ensure the fixture will function properly for many years to come.

• Do not shake fixture, avoid brute force when installing and/or operating the device.

• Always install the fixture with an appropriate safety cable. When installing the fixture in a suspended environment, always use mounting hardware that is no less than M10 x 25 mm, also be sure the hardware is insert in the pre-arranged screw holes in the bracket of the fixture.

• Please use the original packaging and materials to transport the fixture in for service.

• Fixture surface temperature may reach up to

85

°

C

. DO NOT TOUCH the housing bare-hand during its operation. Turn OFF the power and allow approximately 15 minutes for the fixture to cool down before replacing or serving.

8

ARENA PAR ZOOM

™

User Manual 1.0


F I X T U R E O V E R V I E W

1: 3pin DMX IN

2: 3pin DMX OUT

3: 5pin DMX IN

4: 5pin DMX OUT

5: Menu Function Display

6: MODE Button

7: UP Button

8: DOWN Button

9: ENTER Button

10: Power ON

11: DMX Signal

12: PowerCON IN

13: PowerCON OUT

14: Fuse

1. 3pin DMX IN - DMX signal input

2. 3pin DMX OUT - DMX signal output

3. 5pin DMX IN - DMX signal input

4. 5pin DMX OUT - DMX signal output

5. Menu Function Display - Displays function menus and options

6. MODE Button - Used to select programming functions

7. UP Button - Used to toggle forward through selected menu functions

8. DOWN Button - Used to toggle backward through selected menu functions

9. ENTER Button - Used to confirm selected menu functions

10. Power ON - Indicates power is ON

11. DMX Signal - Power connection to power source

12. PowerCON IN - Power supply input to fixture

13. PowerCON OUT - Power link output to next fixture

14. Fuse - Fuse protection against current damage

9

ARENA PAR ZOOM

™

User Manual 1.0


I N S T A L L A T I O N

T he elec tric connection m ust only be carried out by a qualified elec trician.

C A U T I O N S

• The maximum recommended ambient temperature is 104°F (40°C).

Do not use the fixture above this temperature.

• For added protection, mount the fixture in areas outside walking paths, seating areas, or in areas were unauthorized personnel might reach the fixture.

• Before mounting the fixture to any surface, make sure the installation area can hold a minimum point load of 10 times the weight of the fixture. (165 lbs / 75 kgs)

• Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.

• Never stand directly below the device when mounting, removing or servicing the fixture.

• Be sure the fixture is kept at least 0.5m (1.5 feet) away from any flammable materials

(decoration etc.).

P O W E R L I N K I N G

120V 60Hz - ONLY (4) devices may be linked together for power.

Connect device number #5 to a different power source.

230V 50Hz - ONLY (8) devices may be linked together for power.

Connect device number #9 to a different power source.

10

ARENA PAR ZOOM

™

User Manual 1.0


MOUNTING POINTS

• Overhead mounting requires extensive experience, including amongst others calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the device. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury.

• Fixture is fully operational in any mounting position, hanging upside-down, side mounted, or on any flat level surface, and will remain steady no matter the angle of the fixture.

SAFETY CABLE

Always use a Safety Cable whenever installing this fixture in a suspended

environment to ensure the fixture will not drop if the clamp fails.

11

ARENA PAR ZOOM

™

User Manual 1.0


U N D E R S T A N D I N G D M X

DMX-512

DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant. A DMX controller sends the DMX data instructions to the fixture allowing the user to control the different aspects of an intelligent light. DMX data is sent out as serial data that travels from fixture to fixture via data “IN” and data “OUT” XLR terminals located on the fixtures (most controllers will only have output jacks).

DMX LINKING

To ensure proper DMX data transmission, always use proper DMX cables and a terminator.

When using several DMX fixtures try to use the shortest cable path possible. Never split a

DMX line with a “Y” style connector. The order in which the fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a starting DMX address of 1 may be placed anywhere in the DMX chain, at the beginning, at the end, or anywhere in the middle. The DMX controller knows to send data assigned to address 1 to that fixture no matter where it is located in the DMX chain. The ARENA PAR ZOOM™ can be controlled via DMX-512 protocol and the DMX address is set via the control menu.

DATA CABLE (DMX Cable) REQUIREMENTS (For DMX and Master/Slave Operation)

Your fixture and your DMX controller require a standard 3-pin or 5-pin XLR connector for data input and data output (see figure below). If you are making your own cables, be sure to use two conductor, shielded digital DMX cable rated at 120 ohms; this cable is designed for

DMX transmission and may be purchased from your Elation dealer or at most professional lighting retailers. Your cables should be made with a male and female XLR connector on either end of the cable. Also, remember that a DMX line must be daisy chained and cannot be split, unless using an approved DMX splitter such as Elation’s Opto Branch 4™, Opto

Branch 8™, or DMX-Branch/4™.

12

ARENA PAR ZOOM

™

User Manual 1.0


Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR outer casing. Grounding the shield could cause a short circuit and erratic behavior.

DMX-512 CONTROLLER CONNECTION

Connect the provided XLR cable to the female XLR output of your controller and the other side to the male XLR input of the ARENA PAR ZOOM™ (Please refer to the diagram below.). You can chain multiple panels together through serial linking. The cable that should be used is two conductor, shielded DMX cable with XLR input and output connectors.

Always be sure daisy chain your in and out data connections, never split or “Y” your DMX connections unless you are using an approved DMX splitter such as Elation’s Opto Branch

4™, Opto Branch 8™, or DMX-Branch/4™.

13

ARENA PAR ZOOM

™

User Manual 1.0


DMX-512 CONNECTION WITH DMX TERMINATOR

A DMX terminator should be used in all DMX lines especially in longer runs. The use of a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line. Using a line terminator will decrease the possibilities of erratic behavior.

5-Pin XLR DMX CONNECTORS

Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin.

5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard

5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The following chart details a proper cable conversion.

14

ARENA PAR ZOOM

™

User Manual 1.0


DMX ADDRESSING

All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the back of the fixture.

You can set the same starting address for all fixtures or a group of fixtures, or set different address for each individual fixture. Be advised that setting all fixtures to the same DMX address will subsequently control all fixtures in the same fashion, in other words, changing the settings of one channel will affect all the fixtures simultaneously.

If you set each fixture to a different DMX address, each unit will start to “listen” to the channel number you have set, based on the quantity of control channels (DMX channels) of each fixture. That means changing the settings of one channel will only affect the selected fixture.

In the case of the ARENA PAR ZOOM™, when in 10 channel mode (default can also be set to 5 or 6), set the starting DMX address of the first unit to 1, the second unit to 11 (1 + 10), the third unit to 21 (11 + 10), the fourth unit to 31 (21 + 10) and so on. (See diagram below)

15

ARENA PAR ZOOM

™

User Manual 1.0


F I X T U R E M E N U

ON-BOARD SYSTEM MENU

The ARENA PAR ZOOM™ comes with an easy to navigate system menu. The next section will detail the functions of each command in the system menu.

MENU FUNCTION DISPLAY

To select any of the menu functions, press the MODE button until the desired function is displayed. Select the function by pressing the ENTER button and the display will flash. Use the UP and DOWN buttons to change the mode. Once the desired mode has been selected, press the ENTER button to setup, or to go back to the main menu without making any changes press the MENU button again. Hold and press the MODE button about one second to exit the menu mode or wait for one minute and the fixture will exit the menu mode automatically. (The main functions and options are illustrated on the next page)

The MENU display will lock when NO buttons are pressed for 30 seconds. When the display locks, none of the control panel buttons will respond. To unlock the display, press and hold the MODE button 3 seconds to access the menu options once again.

16

ARENA PAR ZOOM

™

User Manual 1.0


17

ARENA PAR ZOOM

™

User Manual 1.0


MAIN FUNCTIONS

DMX Address

Select the DMX Address menu, then press the ENTER button and the display will flash.

Use the UP and DOWN buttons to change the DMX Address (1-512), and then press the

ENTER button to confirm selection. To return back to the previous menu functions without any change press the MODE button.

Channel Mode

Select the Channel Mode menu, then press the ENTER button and the display will flash.

Use the UP and DOWN buttons to select desired DMX Channel Mode (5chan, 6chan or

10chan). Once the desired mode has been selected, press the ENTER button to confirm selection. To return back to the previous menu functions without any change press the

MODE button.

Dimmer Curve

Select the Dimmer Curve menu, then press the ENTER button and the display will flash.

Use the UP and DOWN buttons to select the desired Dimmer Curve Mode (Standard,

Stage, TV, Architectural, Theatre). Once the desired mode has been selected, press the

ENTER button to confirm selection. To return back to the previous menu functions without any change press the MODE button.

18

ARENA PAR ZOOM

™

User Manual 1.0


Black Out

Select the Black Out menu, then press the ENTER button and the display will flash. Use the

UP and DOWN button to select Yes (blackout) or Hold (keeps last value set prior to signal loss). Once the desired mode has been selected, press the ENTER button to confirm selection. To return back to the previous menu functions without any change press the

MODE button.

Back Light

Select the Back Light menu, then press the ENTER button and the display will flash. Use the UP and DOWN buttons to select ON or OFF. Once the desired mode has been selected, press the ENTER button to confirm selection. To return back to the previous menu functions without any change press the MODE button.

White Balance

Select the White Balance menu, then press the ENTER button and the display will flash.

Use the UP and DOWN buttons to select the desired color (Red, Green, Blue) you wish to adjust. Press the ENTER button to confirm your selection and use UP and DOWN button to adjust the value (125~255). Once the desired value has been selected, press the ENTER button to confirm selection. To return back to the previous menu functions without any change press the MODE button.

Manual Test

Select the Manual Test menu, then press the ENTER button and the display will flash. Use the UP and DOWN buttons to select the desired function (Red, Green, Blue, White, Zoom,

Dimmer or Strobe) you wish to test. Once the desired function has been selected, press the ENTER button and the displayed value will begin to flash. You can now adjust the values

(000~255) by pressing the UP and DOWN buttons. Once you have completed testing press the ENTER button. To return back to the previous menu functions without any change press the MODE button.

Auto Test

Select the Auto Test menu, then press the ENTER button and the fixture will run the built-in program for self test. Press the MODE button to exit.

Temp.

Select the Temp. menu, then press the ENTER button and the display will show the current running temperature of the fixture. Press the MODE button to exit.

Fixture Time

Select the Fixture Time menu, then press the ENTER button and the display will show the total running time of the fixture. Press the MODE button to exit.

19

ARENA PAR ZOOM

™

User Manual 1.0


Firmware Version

Select the Firmware Version menu, then press the ENTER button and the display will show the software version of the fixture. Press the MODE button to exit.

Reset

Select the Reset menu, then press the ENTER button and the fixture will now reset itself.

20

ARENA PAR ZOOM

™

User Manual 1.0


D M X C H A N N E L F U N C T I O N S A N D V A L U E S

ELATION© ARENA PAR ZOOM™

DMX Channel Values / Functions (10 DMX Channels)

MODE / CHANNEL

5 6 10

1

2

3

4

1

2

3

4

1

2

3

4

5

6

VALUE

0-255

0-255

0-255

0-7

8-15

16-131

132-139

140-181

182-189

190-231

232-239

240-247

248-255

101-108

109-116

117-123

124-131

132-139

140-147

148-154

155-162

163-170

171-178

179-185

186-193

194-201

202-209

210-216

217-224

225-232

233-240

241-247

248-255

0-255

0-7

8-15

16-23

24-30

31-38

39-46

47-54

55-61

62-69

70-77

78-85

86-92

93-100

Specifications subject to change without any prior written notice.

FUNCTION

RED

Red ( 0-Black , 255-100% Red )

GREEN

Green ( 0-Black , 255-100% Green )

BLUE

Blue ( 0-Black , 255-100% Blue )

WHITE

White ( 0-Black , 255-100% White )

COLOR MACROS

OPEN

Preset Color 1

Preset Color 2

Preset Color 3

Preset Color 4

Preset Color 5

Preset Color 6

Preset Color 7

Preset Color 8

Preset Color 9

Preset Color 10

Preset Color 11

Preset Color 12

Preset Color 13

Preset Color 14

Preset Color 15

Preset Color 16

Preset Color 17

Preset Color 18

Preset Color 19

Preset Color 20

Preset Color 21

Preset Color 22

Preset Color 23

Preset Color 24

Preset Color 25

Preset Color 26

Preset Color 27

Preset Color 28

Preset Color 29

Preset Color 30

Preset Color 31

Preset Color 32

SHUTTER / STROBE

OFF

LEDs ON

Strobe Effect SLOW to FAST

LEDs ON

SLOW Open FAST Close

LEDs ON

SLOW Close FAST Open

LEDs ON

RANDOM Strobe

LEDs ON

21

ARENA PAR ZOOM

™

User Manual 1.0


MODE / CHANNEL

5 6 10

5 5

6

7

8

9

ELATION© ARENA PAR ZOOM™

DMX Channel Values / Functions (10 DMX Channels)

Specifications subject to change without any prior written notice.

10

VALUE

0-255

0-255

0-255

0-41

42-84

85-127

128-170

171-213

214-255

T R O U B L E S H O O T I N G

FUNCTION

DIMMER INTENSITY

Intensity 0 to 100%

ZOOM

WIDE to NARROW

COLOR TEMP

Continuous WHITE color temperature control from 7200k to 3200k

DIMMER CURVES

STANDARD

STAGE

TV

ARCHITECTURAL

THRATRE

DEFAULT to UNIT CURVE SETTING

The following are a few common problems that may occur during operation, and some suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. If DMX LED is not ON, check DMX connectors and cables to see if linked properly.

2. If DMX LED is ON, check DMX address settings and/or DMX polarity.

3. If there are intermittent DMX signal problems, check the pins on the DMX connectors and/or on the PCB of the fixture or the previous one.

4. Try using another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may cause damage and/or interference to the DMX interface circuit.

C. One of the channels is not working well

1. The stepper motor and/or the DMX cable connected to the PCB might be damaged.

2. The motor’s drive IC on the PCB might be damaged.

22

ARENA PAR ZOOM

™

User Manual 1.0


C L E A N I N G A N D M A I N T E N A N C E

CLEANING

Frequent cleaning is recommended to insure proper function, optimized light output, and an extended life. The frequency of cleaning depends on the environment in which the fixture operates: damp, smoky or particularly dirty environments can cause greater accumulation of dirt on the fixture’s optics.

• Clean the external lens surface at least every 20 days with a soft cloth to avoid dirt/debris accumulation.

• Never use alcohol, solvents, or ammonia based cleaners.

MAINTENANCE

Regular inspections are recommended to insure proper function and an extended life.

There are no user serviceable parts inside this fixture, please refer all other service issues to an authorized Elation service technician. Should you need any spare parts, please order genuine parts from your local Elation dealer.

Please refer to the following points during routine inspections:

• A detailed electric check by an approved electrical engineer every three months, to make sure the circuit contacts are in good condition and prevent overheating.

• Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall.

• Check for any deformations on the housing, color lenses, rigging hardware and rigging points (ceiling, suspension, trussing). Deformations in the housing could allow for dust to enter into the fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person(s).

• Electric power supply cables must not show any damage, material fatigue or sediments.

Never remove the ground prong from the power cable.

23

ARENA PAR ZOOM

™

User Manual 1.0


T E C H N I C A L S P E C I F I C A T I O N S

FEATURES

1000-Watt Comparable Lumens Output

Motorized 10° - 60° Zoom

Selectable Dimming Curves & Color Temperatures (3200K - 7200K)

Flicker Free Operation for TV and FILM

SOURCE

19x 10W Osram™ QUAD Color (RGBW) LEDs

50,000 Hour Average Life

PHOTOMETRIC DATA

12,600 LUX @3M 10° Min Zoom

900 LUX @3M 60° Max Zoom

EFFECTS

Strobe + Variable Strobe Macros

Electronic Dimming: 0% - 100%

COLOR

RGBW

CONTROL / CONNECTIONS

3 DMX Channel Modes (5/6/10)

3pin & 5pin DMX In/Out

4 Button Control Panel

LCD Menu Display powerCON Power In/Out

Power Link Up To (4) Units at 120V (8) Units at 230V

SIZE / WEIGHT

Length: 12.8” (324mm)

Width: 10.9” (276mm)

Vertical Height: 14.5” (368mm)

Weight: 15.9 lbs. (7.2kg)

ELECTRICAL / THERMAL

AC 100-240V - 50/60Hz

220W Max Power Consumption

-4°F (-20°C) to 104°F (40°C)

APPROVALS / RATINGS

CE Approved cETLus Pending

IP20 Rated

INSTALLATION

Rigging: Dual Yoke / Floor Stand

Yoke Hole Diameter: 0.47” (12mm)

Working Position: Any (360°)

Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.

24

ARENA PAR ZOOM

™

User Manual 1.0

PHOTOMETRIC DATA w w w . e l a t i o n l i g h t i n g . c o m


25

ARENA PAR ZOOM

™

User Manual 1.0

DIMENSIONAL DRAWINGS w w w . e l a t i o n l i g h t i n g . c o m


26

ARENA PAR ZOOM

™

User Manual 1.0

CIRCUIT SCHEMATICS w w w . e l a t i o n l i g h t i n g . c o m


27

ARENA PAR ZOOM

™

User Manual 1.0


OPTIONAL ACCESSORIES

ORDER CODE ITEM DESCRIPTION

TRIGGER CLAMP Heavy Duty Wrap Around Hook Style Clamp

PLC3 3-foot (1m) PowerCON Link Cable

PLC6 6-foot (1.8m) PowerCON Link Cable

PLC10 10-foot (3m) PowerCON Link Cable

PLC15 15-foot (4.5m) PowerCON Link Cable

AC3PDMX5PRO 5-foot (1.5m) 3-pin PRO DMX Cable

AC3PDMX10PRO 10-foot (3m) 3-pin PRO DMX Cable











28

ARENA PAR ZOOM

™

User Manual 1.0


29

ARENA PAR ZOOM

™

User Manual 1.0

ELATION ARENA PAR ZOOM - USER MANUAL 1.2

ARENA PAR ZOOM™

user manual 1.2

General Information

Warranty

Safety Instructions

General Guidelines

Fixture Overview

Installation

Understanding DMX

Fixture Menu

DMX Channel Functions And Values

Trouble Shooting

Cleaning and Maintenance

Technical Specifications

Optional Accessories

Declaration Of Conformity

9

10

12

16

21

22

23

24

28

29

4

6

7

8

Related manuals

Elation

Arena Par Zoom

Elation

Arena Q7 Zoom

Elation

Arena Q7 Zoom

Elation Professional

Marine Radio Opto Branch 8

Elation

SNIPER 2R

Elation

Rayzor Q12 Zoom

Elation

Satura Spot LED PRO

Elation

Platinum SBX

Elation

ProTron LED