Fanvil Product User Manual IP

Add to my manuals
48 Pages

advertisement

Fanvil Product User Manual IP | Manualzz

http://arttel.ru

Fanvil Product User Manual

IP-Gateway

Model: A2

Version

Ö

V1.0.90.16

© 2005 Fanvil technology Co,. Ltd

All rights reserved.

This document is supplied by Fanvil Technology Co., Ltd, No part of this document may be reproduced, republished or retransmitted in any form or by any means whatsoever, whether electronically or mechanically, including, but not limited to, by way of photocopying, recording, information recording or through retrieval systems, without the express written permission of

Fanvil Technology Co., Ltd. Fanvil Technology Co., Ltd reserves the right to revise this document and make changes at any time and without the obligation to notify any person and/or entity of such revisions and/or changes. Product specifications contained in this document are subject to change without notice.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Safety Notices

Please read the following safety notices before installing or using this gateway.

They are crucial for the safe and reliable operation of the device.

z

Please use the external power supply that is included in the package. Other powers supplies may cause damage to the device, affect the behavior or induce noise.

z

Before using the external power supply in the package, please check with home power voltage. Inaccurate power voltage may cause fire and damage.

z

Please do not damage the power cord. If power cord or plug is impaired, do not use it, it may cause fire or electric shock.

z

The plug-socket combination must be accessible at all times because it serves as the main disconnecting device.

z

Do not drop, knock or shake it. Rough handling can break internal circuit boards.

z

Do not install the device in places where there is direct sunlight. Also do not put the device on carpets or cushions. It may cause fire or breakdown.

z

Avoid exposure the gateway to high temperature, below 0 or high humidity.

Avoid wetting the unit with any liquid.

z

Do not attempt to open it. Non-expert handling of the device could damage it.

Consult your authorized dealer for help, or else it may cause fire, electric shock and breakdown.

z

Do not use harsh chemicals, cleaning solvents, or strong detergents to clean it.

Wipe it with a soft cloth that has been slightly dampened in a mild soap and water solution.

z

When lightning, do not touch power plug or device line, it may cause an electric shock.

z

Do not install this device in an ill-ventilated place.

z

You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Table of Content

1.

W

ELCOME TO THE

A2

TWO

-

PORT GATEWAY

........................................................................... 5

1.1. Package Contents..................................................................................................... 5

2 U

NDERSTANDING OF

A2

TWO

-

PORT GATEWAY

......................................................................... 6

2.1. The positive of A2 two-port gateway ...................................................................... 6

2.2. Indicator signs .......................................................................................................... 7

2.3. Connector description.............................................................................................. 7

3.

G

ETTING

S

TARTED

............................................................................................................... 9

3.1. Connect the power and network ............................................................................. 9

3.1.1. Connect the network ........................................................................................................ 9

3.1.2. Connect the power ......................................................................................................... 10

4.

B

ASIC PHONE OPERATION OF

A2

TWO

-

PORT GATEWAY

..........................................................11

4.1. Call transfer ..............................................................................................................11

4.2. Call hold ....................................................................................................................11

5.

W

EB CONFIGURATION

......................................................................................................... 12

5.1. Introduction of configuration................................................................................. 12

5.1.1. Ways to configure .......................................................................................................... 12

5.1.2. Password Configuration ................................................................................................ 12

5.2. Setting via web browser......................................................................................... 12

5.3. Configuration via WEB ........................................................................................... 13

5.3.1. BASIC .............................................................................................................................. 13

5.3.1.1. Status ........................................................................................................................... 13

5.3.1.2. Wizard........................................................................................................................... 13

5.3.2. Network ........................................................................................................................... 15

5.3.2.1. WAN Config.................................................................................................................. 15

5.3.2.2. LAN Config................................................................................................................... 17

5.3.2.3. Qos Config ................................................................................................................... 18

5.3.2.4. Service Port.................................................................................................................. 20

5.3.2.5. DHCP SERVER............................................................................................................. 21

5.3.2.6. NTP ...............................................................................................................................22

5.3.3. VOIP................................................................................................................................. 22

5.3.3.1. SIP Config .................................................................................................................... 22

5.3.3.2. Stun Config .................................................................................................................. 26

5.3.3.3. DIAL PEER setting....................................................................................................... 27

5.3.4. Phone .............................................................................................................................. 31

5.3.4.1. DSP Config................................................................................................................... 31

5.3.4.2. Call Service .................................................................................................................. 32

5.3.4.3. Digital Map Configuration ........................................................................................... 34

5.3.5. Maintenance.................................................................................................................... 35

5.3.5.1. Auto Provision ............................................................................................................. 35

5.3.5.2. Syslog Config .............................................................................................................. 36

5.3.5.3. Config Setting .............................................................................................................. 37

5.3.5.4. Update .......................................................................................................................... 38

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

5.3.5.5. Account Config............................................................................................................ 38

5.3.5.6. Reboot .......................................................................................................................... 39

5.3.6. Security ........................................................................................................................... 40

5.3.6.1. MMI Filter...................................................................................................................... 40

5.3.6.2. Firewall ......................................................................................................................... 41

5.3.6.3. NAT Config................................................................................................................... 42

5.3.6.4. VPN Config................................................................................................................... 44

5.3.7. Logout ............................................................................................................................. 45

6.

A

PPENDIX

.......................................................................................................................... 46

6.1.

S

PECIFICATION

................................................................................................................ 46

6.1.1.

H

ARDWARE

.................................................................................................................. 46

6.1.2.

V

OICE FEATURES

.......................................................................................................... 46

6.1.3.

N

ETWORK FEATURES

.................................................................................................... 46

6.1.4.

M

AINTENANCE AND MANAGEMENT

................................................................................ 47

6.2.

P

ARTICULARLY SUITABLE FOR

A2

TWO

-

PORT GATEWAY

..................................................... 47

6.3.

C

OMMON

P

ROBLEMS

...................................................................................................... 47

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

1. Welcome to the A2 two-port gateway

1.1. Package Contents

Please check your product packaging

B

it includes:

1. One A2 two-port gateway

2. A group of cable

3. A power adapter

NOTE: if you use the non-A2 two-port gateway comes with a power adapter, two-port gateway may cause damage or other injury. Specifications for the power adapter may different between the different shipment areas. If the power adapter provided with the product can not be used locally, please consult your local dealer.

4. User manual

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

2 Understanding of A2 two-port gateway

A2 two-port gateway IP-based voice media access device is designed for operators, enterprises, residential users, and residential VoIP solution to provide network equipment. A2 two- port gateway into the analog voice information transmitted over

IP networks, which use IP networks to transmit voice. It is full compliance with the

SIP protocol standard, with the market most other SIP compliant devices and server-side.

The gateway will play Internet network (either public network or private network) connecting with the public telephone network bridge. It provides two FXS analog voice interfaces, used for ordinary small business PBX or gateway (PBX).

This site using the most advanced voice processing technologies, such as advanced voice compression standards, echo cancellation, dynamic voice detection, silence detection, ensuring Quality of Service (QoS), and voice quality comparable to regular PSTN phone.

In addition, A2 two-port gateway also integrates a small router function. WEB comes through the gateway configuration page, simply configure the network parameters, can achieve multiple computers and network equipment, broadband access, ideal for small office and home users.

Because this site has a wealth of features and related detailed configuration options, in your call to enjoy a stress free before you know your A2 two-port gateway.

2.1. The positive of A2 two-port gateway

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

2.2. Indicator signs

Name

POWER

FXS1

FXS2

WAN

LAN

Meaning

Power LED

Phone work status lights

Phone work status lights

WAN network interface lights

LAN network interface lights

Description

Always light, has power, you can start using the A2 two-port gateway.

Show the status of the phone under the port 1. No phone or hang up: Off; pick up: always.

Show the status of the phone under the port 2. No phone or hang up: Off; Pick up: always.

Indicator light, WAN port connected to the network.

Flashing: Data transfer.

Indicator light, LAN port connected to the network.

Flashing: Data transfer.

2.3. Connector description

Name

POWER

FXS1

FXS2

Meaning

Power switch

FXS1 Interface

FXS2 Interface

LAN Network Interface

WAN Network Interface

Description

Output:12VDC

B

500mA

Û

Ordinary telephone connection, or switch into the line.

Ordinary telephone connection, or switch into the line.

10/100M Adaptive connected PC.

10/100M Adaptive connected to the RJ45 port of Internet

Û http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

A2 two-port gateway with two network interface itself: WAN port and LAN port, you can use the Internet connection into the WAN port or LAN port. Read the manual carefully of “Safety” before inserting the power

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

3. Getting Started

Before you start using the A2 two-port gateway, please install the following:

3.1. Connect the power and network

3.1.1. Connect the network

During this step, make sure your environment already have broadband Internet access capability.

1. Broadband Router

Direct network connection—by this method, you need at least one available

Ethernet port in your workspace. Use the Ethernet cable in the package to connect

WAN port of A2 two-port gateway to the Ethernet port in your workspace. Since this gateway has router functionality, whether you have a broadband router or not, you can make direct network connect. The following two figures are for your reference.

2. as a broadband router

Use this method if you have a single Ethernet port in your workspace with your desktop computer already connected to it. First, disconnect the Ethernet cable from the computer and attach it to the WAN port of gateway. Next, use the Ethernet cable in the package to connect LAN port of gateway to your desktop computer. Your IP

Phone now shares a network connection with your computer. The following figure is for your reference.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

3.1.2. Connect the power

During this step, make sure your power supply connector and A2 two-port gateway outlet match, while A2 is also in line voltage and current required for a two-port gateway.

1. The transformer connected to the DC port on the back of A2 two-port gateway

POWER jack.

2. The AC adapter plug to an electrical outlet, A2 two-port gateway boot.

3. At this point all of your lights (except the POWER indicator) will flash together.

After booting, you will hear popping sounds, and then the indicator light is lit according to your current configuration corresponding light. (If your light is not normal, you need to further configure your network connection mode).

4. If you login on the gateway server, then you can start calling.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

4. Basic phone operation of A2 two-port gateway

Since there are two FXS interfaces on the A2 two-port gateway, and the two interfaces are independent, so the phones under the FXS1 and FXS2 have the same operation. The phones under the two ports can be used as two separate telephones at the same time. The following operations are applicable to the phones under the

FXS1 and FXS2.

4.1. Call transfer

z

Blind Transfer

During a call, press FLASH (Flash) key, enter the number to be transferred

ô

*

õ

add and press

ô

#

õ

key to confirm, you can transfer the current call to third parties. (To use this feature, you must enable the gateway of the Call Waiting and Call Transfer function)

z

Attended Transfer

During a call, press FLASH (Flash) key, enter the number waiting to be transferred connected, directly hang up, you can transfer successfully. (To use this feature, you must enable the gateway of the Call Waiting and Call Transfer function)

NOTE:1, Call Transfer must call in two cases all the way is free for operation;

2, Gateway (transfer side) and the establishment of phone A calls phone C gateway and then create a call, hang up the phone A, this time the gateway can also initiate the transfer.

3, your VoIP traffic services providers need to support (RFC3515), this feature to work correctly.

4.2. Call hold

z

Call Hold and set aside

During a call you can press FLASH (FLASH) button and enter the number to dial and press

ô

#

õ

key to ensure

Recognition, can retain the current state of the call with third-party calls. If you press the FLASH (Flash) key, you can switch back. You also can send and receive on one side, then the party can not be retained to hear your conversation, the speaker you can not. During a call if you press

ô

*

õ

operation, will enter the three-way calling mode. (To use this feature, you must enable the gateway of the

Call Waiting feature, you must achieve three-way calling mode to start the gateway

Three Way Call function)

z

Call on hold and accept call waiting

In normal conversation, a third party dial-in, the handset will beep ~ beep ~ tips coming, you can use FLASH (Flash) button to accept call waiting. If you press this

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

button again, you can switch back. You also can send and receive on one side, then the party can not be retained to hear your conversation, the speaker you can not.

(To use this feature, you must enable the gateway of the Call Waiting feature)

5. Web configuration

5.1. Introduction of configuration

5.1.1. Ways to configure

A2 two-port gateway has two different ways to different users.

z

Use web browser

>

recommendatory way

?

.

z

Use telnet with CLI command.

5.1.2. Password Configuration

There are two levels to access to gateway: root level and general level. User with root level can browse and set all configuration parameters, while user with general level can set all configuration parameters except SIP (1-2) that some parameters can not be changed, such as server address and port. User will has different access level with different username and password.

z

Default user with general level

P

username

P

guest

password

P

guest

z

Default user with root level

P

username

P

admin

password

P

admin

5.2. Setting via web browser

When this gateway and PC are connected to network, enter the WAN port IP address of the gateway as the URL (e.g. http://xxx.xxx.xxx.xxx/ or http://xxx.xxx.xxx.xxx:xxxx/).

Gateway IP address can be received by dialing # * 111.

The login page is shown as below

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

5.3. Configuration via WEB

5.3.1. BASIC

5.3.1.1. Status

Field name

Network

Status

Explanation

Shows the configuration information on WAN and

LAN port, including the connect mode of WAN port

(Static, DHCP, PPPoE), MAC address, the IP addresses of WAN port and LAN port, ON or OFF of

DHCP mode of LAN port.

Phone Number Shows the phone numbers provided by the SIP LINE

1-2 servers.

The last line shows the version number and issued date.

5.3.1.2. Wizard

Field Name

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

Wizard

Explanation

http://arttel.ru

Please select the proper network mode according to the network condition.

A2 gateway provide three different network settings:

z

Static: If your ISP server provides you the static IP address, please select this mode, and then finish Static Mode setting. If you don’t know about parameters of Static Mode setting, please ask your ISP for them.

z

DHCP: In this mode, you will get the information from the DHCP server automatically; need not to input this information artificially.

z

PPPoE: In this mode, you must input your ADSL account and password.

You can also refer to 3.2.1 to quick set your network.

Choose Static IP MODE

B

click

ô

NEXT

õ

can config the network and SIP(default

SIP1)simply, also can browse too. Click

ô

BACK

õ

can return to the last page.

Static IP Address Input the IP address distributed to you.

Netmask Input the Netmask distributed to you.

Gateway

DNS Domain

Input the Gateway address distributed to you.

Set DNS domain postfix. When the domain which you input can not be parsed, gateway will automatically add

Primary DNS

Alter DNS this domain to the end of the domain which you input before and parse it again.

Input your primary DNS server address.

Input your alternate DNS server address.

Display Name Set the display name.

Server Address Input your SIP server address.

Server Port Set your SIP server port.

User Name Input your SIP register account name.

Password Input your SIP register password.

Phone Number Input the phone number assigned by your VOIP service provider.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Enable Register Start to register or not by selecting it or not.

Display detailed information that you manual config.

Choose DHCP MODE

B

click

ô

NEXT

õ

can config SIP(default SIP1)simply, also can browse too. Click

ô

BACK

õ

can return to the last page. Like Static IP

MODE

Û

Choose PPPoE MODE

B

click

ô

NEXT

õ

can config the PPPoE account/password and SIP(default SIP1)simply, also can browse too. Click

ô

BACK

õ

can return to the last page. Like Static IP MODE

Û

PPPoE Server It will be provided by ISP.

Username Input your ADSL account.

Password Input your ADSL password.

Notice: Click

ô

Finish

õ

button after finished your setting, gateway will save the setting automatically and reboot, After reboot, you can dial by the SIP account.

5.3.2. Network

5.3.2.1. WAN Config

WAN Config

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Field Name explanation

Active IP The current IP address of the gateway.

Current Netmask The current Netmask address.

MAC Address The current MAC address of the gateway.

Current Gateway The current Gateway IP address.

Get MAC Time Shows the time of getting MAC address

Please select the proper network mode according to the network condition.

A2 two-port gateway provide three different network settings:

z

Static: If your ISP server provides you the static IP address, please select this mode, and then finish Static Mode setting. If you don’t know about parameters of Static Mode setting, please ask your ISP for them.

z

DHCP: In this mode, you will get the information from the DHCP server automatically; need not to input this information artificially.

z

PPPoE: In this mode, your must input your ADSL account and password.

You can also refer to 3.2.1 Network to quick set your network.

Obtain DNS server automatically

Select it to use DHCP mode to get DNS address, if you don’t select it, you will use static DNS server. The default is selecting it.

If you use static mode, you need set it.

IP Address

Netmask

Gateway

DNS Domain

Input the IP address distributed to you.

Input the Netmask distributed to you.

Input the Gateway address distributed to you.

Set DNS domain postfix. When the domain which you input can not be parsed, gateway will automatically add

Primary DNS

Alter DNS this domain to the end of the domain which you input before and parse it again.

Input your primary DNS server address.

Input your alternate DNS server address.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

If you uses PPPoE mode

B

you need to make the above setting.

PPPoE Server

Username

It will be provided by ISP.

Input your ADSL account.

Password Input your ADSL password.

Notice:

1

?

Click “Apply” button after finished your setting, IP gateway will save the setting automatically and new setting will take effect.

2

?

If you modify the IP address, the web will not response by the old IP address. Your need input new IP address in the address column to logon in the web.

3

?

If networks ID which is DHCP server distributed is same as network ID which is used by LAN of system, system will use the DHCP IP to set WAN, and modify LAN’s networks ID(for example, system will change LAN IP from 192.168.10.1 to 192.168.11.1) when system uses DHCP client to get IP in startup; if system uses DHCP client to get IP in running status and network ID is also same as LAN’s, system will refuse to accept the IP to configure WAN. So WAN’s active IP will be 0.0.0.0

5.3.2.2. LAN Config

Field name

LAN IP

Netmask

DHCP Service

LAN Config

Specify LAN static IP. explanation

Specify LAN Netmask.

Select the DHCP server of LAN port or not. After you modify the LAN IP address, gateway will amend and adjust the DHCP Lease Table and save the result amended automatically according to the IP address and

Netmask. You need restart the gateway and the DHCP server setting will take effect.

NAT

Bridge Mode

Select NAT or not.

Select Bridge Mode or not: If you select Bridge Mode, the gateway will no longer set IP address for LAN physical port

B

LAN and WAN will join in the same network. Click “Apply”, the gateway will reboot.

Notice: If you choose the bridge mode, the LAN configuration will be

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

disabled.

5.3.2.3. Qos Config

The gateway support 802.1Q/P protocol and DiffServ configuration. VLAN functionality can use different VLAN IDs by setting signal/voice VLAN and data

VLAN. The VLAN application of this device is very flexible.

In chart 1, there is two-layer switch without setting VLAN. Any broadcast frame will be transmitted to the other ports except the send port. For example, a broadcast information is sent out from port 1 then transmitted to port 2,3and 4.

In chart 2, red and blue indicate two different VLANs in the switch, and port 1 and port 2 belong to red VLAN, port 3 and port 4 belong to blue VLAN. If a broadcast frame is sent out from port 1, switch will transmit it to port 2, the other port in the red VLAN and not transmit it to port3 and port 4 in blue VLAN. By this means, VLAN divide the broadcast domain via restricting the range of broadcast frame transmit ion.

Note: chart 2 use red and blue to identify the different VLAN, but in practice, VLAN uses different VLAN IDs to identify.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Field name

VLAN Enable

QoS Configuration

explanation

Before select it to enable VLAN, you need enable Bridge

VLAN

Enable

ID Check

Voice/Data VLAN differentiated mode in LAN config.

Enable VLAN ID check by selecting it. After enable

VLAN ID check, if VLAN ID of a data package is not the same with the gateway or a data package do not have

VLAN ID, the data package will be discarded.

After enable VLAN, system will set packets with different type of VLAN ID. Undifferentiated means after using VLAN, both VoIP packets and other data packets will use the voice VLAN ID; tag differentiated means after using VLAN, VoIP(signal and voice) packets will add voice VLAN ID, and other data packets will add data

VLAN ID; data untagged means after using VLAN, only

VoIP packets will add voice VLAN ID. Other data packets will not use VLAN.

DiffServ Enable Select it or not to Enable or disable DiffServ.

DiffServ Value

Voice 802.1P

Set DiffServ value, the common value is 0x00.

Specify 802.1P Priority of voice/signal data package.

Priority

Data 802.1P

Priority

Voice VLAN ID

Data VLAN ID

Set 802.1p of data VLAN. Non-VoIP data (such as http, telnet, ping etc) will use this value to set VLAN package.

Set VLAN ID of voice/signal data package.

Set 802.1q of data VLAN ID. Non-VoIP data (such as http, telnet, ping etc) will use this value to set VLAN package.

Notice

P

1

?

Startup VLAN, if set Voice/Data VLAN differentiated as Undifferentiated, all packets will use the Voice VLAN ID as the tag.

2) Startup VLAN, if set Voice/Data VLAN differentiated as tag differentiated and disables the DiffServ, then system will not distinguish the voice and data, all packets will use the Voice VLAN ID as the tag.

3) Startup VLAN, if set Voice/Data VLAN differentiated as tag differentiated and enables the DiffServ, then system will distinguish the voice and data and add the VLAN ID each other.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

4) Startup VLAN, if set Voice/Data VLAN differentiated as data untagged, then the packet of the signal/voice will use the Voice VLAN ID as the tag, but the data packets will not take the VLAN tag.

5) If Disable the VLAN, regardless to set the Voice/Data VLAN differentiated or not, all packets will not take the VLAN tag; If enable the DiffServ, all packets will only take the DiffServ value.

6) One must to notice, enable the VLAN ID Check Enable that is default, If enable it, the gateway will match the VLAN ID strictly. When others' VLAN

ID not matches with us, the packets will discard. Contrarily, the gateway will accept the packets with the distinct VLAN ID.

7) You must gain the IP with the Static mode when you set VLAN, otherwise can't gain the IP in the VLAN and also can not dial with point to point.

5.3.2.4. Service Port

You can set the port of HTTP/RTP by this page.

Field name

HTTP Port

SERVICE PORT

explanation set web browse port, the default is 80 port

B

if you want to enhance system safety

B

you'd better change it into non-80 standard port

Q

Example: The IP address is 192.168.1.70. and the port value is 8090, the accessing address is http://192.168.1.70:8090

RTP Initial Port Set the RTP Initial Port. It is dynamic allocation.

RTP Port Quantity Set the maximum quantity of RTP Port, the default is

200.

Notice:

1

?

2

?

If you modify the port of Telnet and HTTP, you would better set the value more than 1024 because the port value less than 1024 is system port reserved.

3

?

if you set 0 for the HTTP port, it will disable HTTP service.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

5.3.2.5. DHCP SERVER

Field name

DHCP SERVER

explanation

DHCP Leased

Table

IP-MAC mapping table. If the LAN port of the gateway connects to a device, this table will show the IP and

MAC address of this device.

Shows the DHCP Lease Table

B

the unit of Lease time is Minute.

Lease Table Name Specify the name of the lease table

Start IP

End IP

Set the start IP address of the lease table

Set the end IP address of the lease table, the network device connected to LAN port will get IP address

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Netmask

Gateway

Lease Time

DNS between Start IP and End IP by DHCP.

Set the Netmask of the lease table

Set the Gateway of the lease table

Set the Lease Time of the lease table

Set the default DNS server IP of the lease table; Click the Add button to submit and add this lease table

Select name of lease table, click the Delete button will delete the selected lease table from DHCP lease table.

DNS Relay

Select DNS Relay, the default is enabled. Click the

Apply button to become effective.

Notice:

1

?

The size of lease table can not be larger than the quantity of C network IP address. We recommend you to use the default lease table and not modify it.

2

?

reboot.

5.3.2.6. NTP

Setting time zone and NTP (Simple Network Time Protocol) server according to your location, you can also manually adjust date and time in this web page.

Field name

Server

Time Zone

Time Out

NTP

NTP

explanation

Set NTP Server IP address.

Select the Time zone according to your location.

Set the time out, the default is 60 seconds.

Select the NTP, and click Apply to make the NTP Times effective.

5.3.3. VOIP

5.3.3.1. SIP Config

Set your SIP server in the following interface.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Field name

SIP Config

explanation

Choose line to set info about SIP, there are 3 lines to choose. You can switch by

ô

Load

õ

button.

Register Status Shows if the gateway has been registered the SIP server or not; or so, show Unapplied;

Server Name Set the server name.

Server Address Input your SIP server address.

Server Port Set your SIP server port.

Account Name Input your SIP register account name.

Password Input your SIP register password.

Phone Number Input the phone number assigned by your VoIP

Display Name service provider. Phone will not register if there is no phone number configured.

Set the display name.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Proxy Server

Address

Set proxy server IP address

>

Usually, Register SIP

Server configuration is the same as Proxy SIP

Server. But if your VoIP service provider give different configurations between Register SIP

Server and Proxy SIP Server, you need make different settings.

?

Proxy Server Port Set your Proxy SIP server port.

Proxy Username Input your Proxy SIP server account.

Proxy Password Input your Proxy SIP server password.

Set the sip domain if needed, otherwise this VoIP

Domain Realm gateway will use the Register server address as sip domain automatically. (Usually it is same with registered server and proxy server IP address).

Port Select To select port for SIP accounts (port1 corresponds

FXS1, port2 corresponds FXS2).

Enable Register Start to register or not by selecting it or not.

Register Expire

Time

Set expire time of SIP server register, default is 60 seconds. If the register time of the server requested is longer or shorter than gateway configured time, the gateway will change automatically the time into the time recommended by the server, and register

NAT Keep Alive

Interval

User Agent

DTMF Mode again.

Set examining interval of the server, default is 60 seconds

Set the user agent if have, the default is VoIP Phone

1.0

Select DTMF sending mode, there are three modes:

z

DTMF_RELAY

z

DTMF_RFC2833

z

DTMF_SIP_INFO

Different VoIP Service providers may provide different modes.

Set the key for RTP encryption Media Key

Local port

RFC Privacy

Edition

Transfer Expire

Time

Set sip port of each line

Set Anonymous call out safely; Support

RFC3323and RFC3325;

For the gateway supports the transfer of certain special features server, set interval time between

Enable Keep

Authentication sending “bye” and hanging up after the phone transfers a call.

Enable/Disable Keep Authentication System will take the last authentication field which is passed the authentication by server to the request packet. It will decrease the server’s repeat authorization work, if it

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

NAT Keep Alive is enable.

Enable/Disable keeps NAT of SIP alive.

If some server refuse to register with too short interval time, and has no packets sending to device in private network to keep NAT alive, user could set this function ON. And set the interval time less than the NAT server’s.

Enable Via report Enable/Disable system to support RFC3581. Via report is special way to realize SIP NAT.

Enable PRACK Enable or disable SIP PRACK function, suggest use the default config.

Long Contact Set more parameters in contact field; connection with

SEM server

Convert # to %23 when send the URI. Enable URI

Convert

Dial Without

Register

Ban Anonymous

Set call out by proxy without registration;

Set to ban Anonymous Call;

Call

Forward Type

Select call forward mode, the default is Off

z

Off

P

Close down calling forward

z

Busy

P

If the phone is busy, incoming calls will be forwarded to the appointed phone.

z

No answer: If there is no answer, incoming calls will be forwarded to the appointed phone.

z

Always

P

Incoming calls will be forwarded to the appoint phone directly.

The phone will Prompt the incoming while doing forward.

Appoint your forward phone number. Forward Phone

Number

Server Type

Subscribe Expire

Time

RFC Protocol

Edition

Select the special type of server which is encrypted, or has some unique requirements or call flows.

Overtime of resending subscribe packet. Suggest using the default config.

Select SIP protocol version to adapt for the SIP server which uses the same version as you select.

For example, if the server is CISCO5300, you need to change to RFC2543; else phone may not cancel call normally. System uses RFC3261 as default.

Transport Protocol Set transport protocols, TCP or UDP;

MWI Number Input the number of the server's voice-mail box

Enable DNS SRV Support DNS looking up with _sip.udp mode

Enable subscribe Enable the option, the gateway will receive the

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

RTP Encode

Enable Session

Timer

Answer With

Single Codec notify from the server.

Enable/Disable RTP Encrypt.

Set Enable/Disable Session Timer, whether support

RFC4028.It will refresh the SIP sessions.

Enable/Disable the function when call is incoming, phone replies SIP message with just one codec which phone supports.

Set to use automatically TCP protocol to guarantee Auto TCP usability of transport as message is above 1300 byte

Enable Strict Proxy Support the special SIP server-when phone receives the packets sent from server

B

phone will use the source IP address, not the address in via field.

Enable GRUU

Enable Display name Quote

Set to support GRUU

Set to make quotation mark to display name as the phone sends out signal, in order to be compatible with server.

5.3.3.2. Stun Config

In this web page, you can config SIP STUN.

STUN:

By STUN server, the gateway in private network could know the type of NAT and the NAT mapping IP and port of SIP. The gateway might register itself to SIP server with global IP and port to realize the device both calling and being called in private network.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

STUN

Field name explanation

STUN NAT Transverse Shows STUN NAT Transverse estimation, true

STUN Server Addr Set your SIP STUN Server IP address

STUN Server Port Set your SIP STUN Server Port

Set STUN Effective Time. If NAT server finds that a

STUN Effect Time means STUN can penetrate NAT, while False means not.

Local SIP Port

NAT mapping is idle after time out, it will release the mapping and the system need send a STUN packet to keep the mapping effective and alive.

Set the SIP port.

Choose line to set info about SIP, There are 2 lines to choose. You can switch by

ô

Load

õ

button.

Use Stun Enable/Disable SIP STUN.

Notice: SIP STUN is used to realize SIP penetration to NAT. If your phone configures STUN Server IP and Port (default is 3478), and enable SIP Stun, you can use the ordinary SIP Server to realize penetration to NAT.

5.3.3.3. DIAL PEER setting

T his functionality offers you more flexible dial rules; you can refer to the following content to know how to use this dial rule. When you want to dial an IP address, the entry of IP addresses is very cumbersome, but by this functionality, you can set number 156 to replace 192.168.1.119 here.

When you want to dial a long distance call to Beijing, you need dial an area code 010 before local phone number, but you can also dial number 1 instead of 010 after we make a setting according to this dial rule. For example, you want to dial

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

01062213123, but you need dial only 162213123 to realize your long distance call after you make this setting.

To save the memory and avoid abundant input of user, add the follow functions:

1

Ú

x Match any single digit that is dialed.

If user makes the above configuration, after user dials 11 digit numbers started with

13, the phone will send out 0 plus the dialed numbers automatically.

2

Ú

[] Specifies a range that will match digit. It may be a range, a list of ranges separated by commas, or a list of digits.

If user makes the above configuration, after user dials 11 digit numbers started with from 135 to 139, the phone will send out 0 plus the dialed numbers automatically.

Use this phone you can realize dialing out via different lines without switch in web interface.

Field name

Phone number

DIAL PEER

explanation

There are two types of matching conditions: one is full matching, the other is prefix matching. In the Full matching, you need input your desired phone number in this blank, and then you need dial the phone number to realize calling to what the phone number is mapped. In the prefix matching, you need input your desired prefix number and T; then dial the prefix and a

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Destination phone number to realize calling to what your prefix number is mapped. The prefix number supports at most 30 digits

Set Destination address. This is optional config item.

If you want to set peer to peer call, please input destination IP address or domain name. If you want to use this dial rule on SIP2 line, you need input

255.255.255.255 or 0.0.0.2 in it.SIP3 into 0.0.0.3

Port

Alias

Set the Signal port, the default is 5060 for SIP.

Set alias. This is optional config item. If you don’t set

Alias, it will show no alias.

Note: There are four types of aliases.

1) add: xxx, it means that you need dial xxx in front of phone number, which will reduce dialing number length.

2) all: xxx, it means that xxx will replace some phone number.

3) del: It means that phone will delete the number with length appointed.

4) Rep: It means that phone will replace the number with length and number appointed.

You can refer to the following examples of different alias application to know more how to use different aliases and this dial rule.

Call Mode Select different signal protocol, SIP

Suffix Set suffix, this is optional config item. It will show no suffix if you don’t set it.

Delete Length Set delete length. This is optional config item. For example: if the delete length is 3, the phone will delete the first 3 digits then send out the rest digits. You can refer to examples of different alias application to know how to set delete length.

Examples of different alias application

Set by web explanation example

You need set phone number, Destination, Alias and Delete Length.

Phone number is XXXT;

Destination is

255.255.255.255 (0.0.0.2) and Alias is del.

This means any phone No. that starts with your set phone number will be sent via SIP2 line after the first several digits of your dialed

If you dial

“93333”, the

SIP2 server will receive “3333”

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

phone number are deleted according to delete length.

This setting will realize speed dial function, after you dialing the numeric key

“2”, the number after all will be sent out.

When you dial

“2”, the SIP1 server will receive

33334444

The phone will automatically send out alias number adding your dialed number, if your dialed number starts with your set phone number.

When you dial

“8309“, the SIP1 server receive will

“07558309”

You need set Phone

Number, Alias and Delete

Length. Phone number is

XXXT and Alias is rep:xxx

If your dialed phone number starts with your set phone number, the first digits same as your set phone number will be replaced by the alias number specified and New phone number will be send out.

When you dial

“0106228”, the

SIP1 server will receive

“86106228”

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

If your dialed phone number starts with your set phone number. The phone will send out your dialed phone number adding suffix number.

When you dial

“147”, the SIP1 server will receive

“1470011”

5.3.4. Phone

5.3.4.1. DSP Config

In this page, you can configure voice codec, input/output volume and so on.

Field name

Port Select

First Codec

Second Codec

Third Codec

Forth Codec

CallerID Tx Mode

Fax Mode

Output Volume

G729 Payload

Length

DSP Configuration

explanation

Select port for setting

The fist preferential DSP codec: G.711A/u, G.726-32,

G.729

The second preferential DSP codec: G.711A/u, G.726-32,

G.729

The third preferential DSP codec: G.711A/u, G.726-32,

G.729

The forth preferential DSP codec: G.711A/u, G.726-32,

G.729

Set the standard only supports sending DTMF CallerID of the PSTN phone.

Set fax mode.

Specify Output (receiver) Volume grade.

Set G729 Payload Length

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Signal Standard

Flashhook Min

Time

Flashhook Max

Time

DTMF Payload

Type

VAD

Select Signal Standard.

Set the minimum time detection of inserted spring.

Set the maximum time inserted spring.

DTMF effective load

Select it or not to enable or disable VAD. If enable VAD,

G729 Payload length could not be set over 20ms.

Notice: In the use of gateway for fax, avoid two fax devices in the same room

5.3.4.2. Call Service

In this web page, you can configure Hotline, Call Transfer, Call Waiting, 3 Ways Call,

Black List, and Limit List and so on.

Field name

Port Select

Hotline

Call Service

explanation

Select port for setting.

Specify Hotline number. If you set the number, you can not dial any other numbers.

Warm line time Automatically after configuration hooks time to call the hotline number. If configured to 0, the hook immediately

P2P IP Prefix after the call the hotline number

Set Prefix in peer to peer IP call. For example: what you want to dial is 192.168.1.119, If you define P2P IP Prefix as

192.168.1., you dial only #119 to reach 192.168.1.119.

Default is “.”. If there is no “.” Set, it means to disable dialing IP.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

No Answer Specify No Answer Time

Time

Do Not Disturb Select NO Disturb, the phone will reject any incoming call,

Accept Any

Call

Enable Call the callers will be reminded by busy, but any outgoing call from the phone will work well.

If select it, the phone will accept the call even if the called number is not belong to the phone.

Enable Call Transfer by selecting it.

Transfer

Ban Outgoing If you select Ban Outgoing to enable it, and you can not dial out any number.

Enable

Three Way Call

Enable Three Way Call

Enable Call Waiting by selecting it. Enable Call

Waiting

Black List

Set Add/Delete Black list. If user does not want to answer some phone calls, add these phone numbers to the Black

List, and these calls will be rejected. x and. Are wildcard. x means matching any single digit. for example, 4xxx expresses any number with prefix 4 which length is 4 will be forbidden to dialed out

DOT (.) means matching any arbitrary number digit. For example, 6. expresses any number with prefix 6 will be forbidden to dial out.

If user wants to allow a number or a series of number incoming, he may add the number(s) to the list as the white list rule. the configuration rule is -number, for example,

-123456, or -1234xx

Limit List

Means any incoming number is forbidden except for 4119

Note: End with DOT (.) when set up the white list

Set Add/Delete Limit List. Please input the prefix of those phone numbers which you forbid the phone to dial out. For example, if you want to forbid those phones of 001 as prefix to be dialed out, you need input 001 in the blank of limit list, and then you can not dial out any phone number whose prefix is 001.

X and. Are wildcard. X means matching any single digit. for example, 4xxx expresses any number with prefix 4 which length is 4 will be forbidden to dialed out

. Means matching any arbitrary number digit. For example,

6. expresses any number with prefix 6 will be forbidden to dial out.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Notice: Black List and Limit List can record at most10 items respectively.

5.3.4.3. Digital Map Configuration

This system supports 4 dial modes:

1). End with “#”: dial your desired number, and then press #.

2). Fixed Length: the phone will intersect the number according to your specified length.

3). Time Out: After you stop dialing and waiting time out, system will send the number collected.

4). User defined: you can customize digital map rules to make dialing more flexible.

It is realized by defining the prefix of phone number and number length of dialing.

In order to keep some users' secondary dialing manner when dialing the external line with PBX, phone can be added a special rule to realize it. So user can dial a number as external line prefix and get the secondary dial tone to keep dial the external number. After finishing dialing, phone will send the prefix and external number totally to the server.

For example, there is a rule 9, xxxxxxxx in the digital map table. After dialing 9, phone will send the secondary dial tone, user may keep going dialing. After finished, phone will call the number which starts with 9; actually the number sent out is

9-digit with 9.

Field name

End with "#"

Fixed Length

Time out

Digital Map Configuration

explanation

Set Enable/Disable the phone ended with “#” dial.

Specify the Fixed Length of phone ending with.

Set the timeout of the last dial digit. The call will be sent after timeout.

Below is user-defined digital map rule:

[] Specifies a range that will match digit. May be a range, a list of ranges separated by commas, or a list of digits. x Match any single digit that is dialed.

. Match any arbitrary number of digits including none.

Tn Indicates an additional time out period before digits are sent of n seconds

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

in length. n is mandatory and can have a value of 0 to 9 seconds. Tn must be the last 2 characters of a dial plan. If Tn is not specified it is assumed to be T0 by default on all dial plans.

Cause extensions 1000-8999 to be dialed immediately

Cause 8 digit numbers started with 9 to be dialed immediately

Cause 911 to be dialed immediately after it is entered.

Cause 99 to be dialed after 4 seconds.

Cause any number started with 9911 to be dialed 4 seconds after dialing ceases.

Notice: End with “#”, Fixed Length, Time out and Digital Map Table can be used simultaneously, System will stop dialing and send number according to your set rules.

5.3.5. Maintenance

5.3.5.1. Auto Provision

Field name

Current Config

Version

Server

Address

Auto Provision

explanation

Show the current config file’s version.

Set FTP/TFTP/HTTP server IP address for auto update.

The address can be IP address or Domain name with subdirectory.

Username

Password

Set FTP server Username. System will use anonymous if username keep blank.

Set FTP server Password.

Config File Name Set configuration file’s name which need to update.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

System will use MAC as config file name if config file name keep blank. For example, 000102030405.

Û

Input the Encrypt Key, if the configuration file is Config Encrypt

Key encrypted.

Protocol Type Select the Protocol type FTP

Ú

TFTP or HTTP.

Update Interval Set update interval time, unit is hour.

Time

Different update modes:

Update Mode

1. Disable: means no update

2. Update after reboot: means update after reboot.

3. Update at time interval: means periodic update.

5.3.5.2. Syslog Config

Syslog is a protocol which is used to record the log messages with client/server mechanism. Syslog server receives the messages from clients, and classifies them based on priority and type. Then these messages will be written into log by some rules which administrator can configure. This is a better way for log management.

8 levels in debug information:

Level 0---emergency: This is highest default debug info level. You system can not work.

Level 1---alert: Your system has deadly problem.

Level 2---critical: Your system has serious problem.

Level 3---error: The error will affect your system working.

Level 4---warning: There are some potential dangers. But your system can work.

Level 5---notice: Your system works well in special condition, but you need to check its working environment and parameter.

Level 6---info: the daily debugging info.

Level 7---debug: the lowest debug info. Mainly be used to output debugging information.

At present, the lowest level of debug information send to Syslog is info; debug level only can be displayed on telnet.

Field name

Server IP

Syslog Configuration

explanation

Set Syslog server IP address.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Server Port Set Syslog server port.

MGR Log Level Set the level of MGR log.

SIP Log Level Set the level of SIP log.

Enable Syslog Select it or not to enable or disable syslog.

5.3.5.3. Config Setting

Field name

Save Config

Clear Config

Config Setting

explanation

You can save all changes of configurations. Click the

Save button, all changes of configuration will be saved, and be effective immediately. .

Backup Config Right clicks on “Right click here…” and select “Save

Target As….” then you will save the config file in .txt format

User can restore factory default configuration and reboot the gateway.

If you login as Admin, the gateway will reset all configurations and restore factory default; if you login as Guest, the gateway will reset all configurations except for VoIP accounts (SIP1-2 and IAX2) and version number.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

5.3.5.4. Update

You can update your configuration with your config file in this web page.

Field name

Web Update

Server

Username

Password

File name

Update

explanation

Click the browse button, find out the config file saved before or provided by manufacturer, download it to the gateway directly, press “Update” to save. You can also update downloaded update file, logo picture, ring, mmiset file by web.

Set the FTP/TFTP server address for download/upload.

The address can be IP address or Domain name with subdirectory.

Set the FTP server Username for download/upload.

Set the FTP server password for download/upload.

Set the name of update file or config file. The default name is the MAC of the gateway, such as

000102030405.

Notice: You can modify the exported config file. And you can also download config file which includes several modules that need to be imported. For example, you can download a config file just keep with SIP module. After reboot, other modules of system still use previous setting and are not lost.

Action type that system want to execute

P

Type

1. Application update: download system update file

2. Config file export: Upload the config file to FTP/TFTP server, name and save it.

3. Config fie import: Download the config file to gateway from FTP/TFTP server. The configuration will be effective after the gateway is reset.

Select FTP/TFTP server Protocol

5.3.5.5. Account Config

You can add or delete user account, and change the authority of each user account in this web page:

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Field name

Account Configuration

explanation

This table shows the current user existed.

User Name Set account user name.

User Level Set user level, Root user has the right to modify configuration, General can only read.

Password

Confirm

Set the password.

Confirm the password.

Select the account and click the Modify to modify the selected account, and click the Delete to delete the selected account. It can add up to 5 users.

General user only can add the user whose level is General.

5.3.5.6. Reboot

If you modified some configurations which need the gateway’s reboot to be effective, you need click the Reboot, then the gateway will reboot immediately.

Notice: Before reboot, you need confirm that you have saved all configurations.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

5.3.6. Security

5.3.6.1. MMI Filter

MMI Filter

User could make some device own IP, which is pre-specified, access to the

MMI of the gateway to config and manage the gateway.

Field name explanation

MMI Filter IP Table list:

Add or delete the IP address segments that access to the phone.

Set initial IP address in the Start IP column, Set end IP address in the End IP column, and click Add to add this IP segment. You can also click Delete to delete the selected IP segment.

MMI Filter Select it or not to enable or disable MMI Filter. Click

Apply to make it effective.

Notice: Do not set your visiting IP outside the MMI filter range; otherwise, you can not logon through the web.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

5.3.6.2. Firewall

Firewall Configuration

In this web interface, you can set up firewall to prevent unauthorized

Internet users from accessing private networks connected to the Internet

(input rule), or prevent unauthorized private network devices from accessing the Internet (output rule).

Firewall supports two types of rules: input access rule and output access rule. Each type supports at most 10 items.

Through this web page, you could set up and enable/disable firewall with input/output rules. System could prevent unauthorized access, or access other networks set in rules for security. Firewall, is also called access list, is a simple implementation of a Cisco-like access list (firewall). It supports two access lists: one for filtering input packets, and the other for filtering output packets. Each kind of list could be added 10 items.

We will give you an instance for your reference.

Field name explanation

In access enable Select it to Enable in_ access rule out access Select it to Enable out_ access rule enable

Input/Output

Deny/Permit

Specify current adding rule by selecting input rule or output rule.

Specify current adding rule by selecting Deny rule or

Permit rule.

Protocol Type Filter protocol type. You can select TCP, UDP, ICMP, or

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Src Addr

IP.

Set source address. It can be single IP address, network address, complete address 0.0.0.0, or network address similar to *.*.*.0

Src Mask

Set the source address’ mask. For example,

255.255.255.255 means just point to one host;

255.255.255.0 means point to a network which network ID is C type.

Src Port Range Set the filter Src Port range

Des Addr Set the destination address. It can be IP address, network address, complete address 0.0.0.0, or network

Des Mask address similar to *.*.*.*

Set the

destination address’ mask. For example,

255.255.255.255 means just point to one host;

255.255.255.0 means point to a network which network ID is C type.

Des Port Range Set the filter Des Port range

Click the Add button if you want to add a new output rule.

Then enable out access, and click the Apply button.

So when devices execute to ping 192.168.1.118, system will deny the request to send ICMP request to 192.168.1.118 for the out access rule. But if devices ping other devices which network ID is 192.168.1.0, it will be normal.

Click the Delete button to delete the selected rule.

5.3.6.3. NAT Config

NAT is abbreviated from Net Address Translation; it’s a protocol responsible for IP address translation. In other word, it is responsible for transforming IP and port of private network to public, also is the IP address mapping which we usually say.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Field name

IPSec ALG

FTP ALG

NAT Configuration

explanation

It is an encryption technology. Select it to enable IPSec

ALG, the default is enable

FTP is a service of connection layer which can transform intranet IP into extranet IP when intranet IP is sending out packet.

Select it to enable FTP ALG, the default is enable

Select it enable PPTP ALG, the default is enable PPTP ALG

Shows the NAT TCP mapping table

Shows the NAT UDP mapping table

Transfer Type

Inside IP

Select the NAT mapping protocol style, TCP or UDP

Set the IP address of device which is connected to LAN interface to do NAT mapping.

Set the LAN port of the NAT mapping Inside Port

Outside Port Set the WAN port of the NAT mapping

Notice: After finish setting, click the Add button to add new mapping table;

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

click the Delete button to delete the selected mapping table.

5.3.6.4. VPN Config

This web page provides us a safe connect mode by which we can make remote access to enterprise inner network from public network. That is to say, you can set it to connect public networks in different areas into inner network via a special tunnel.

Field name

VPN IP

VPN Configuration

explanation

Shows the current VPN IP address

Select UDP Tunnel (VPN Tunnel) or VPN L2TP. You can choose only one for current state. After you select it, you’d better save configuration and reboot your device.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Enable VPN Select it or not to enable or disable VPN

Q

VPN Server Addr Set VPN L2TP Server IP address

VPN User Name Set User Name access to VPN L2TP Server

VPN Password Set Password access to VPN L2TP Server

VPN Server Addr Set VPN PPTP Server IP address

VPN User Name Set User Name access to VPN PPTP Server

VPN Password Set Password access to VPN PPTP Server

5.3.7. Logout

Click Logout

B

and you will exit web page. If you want to enter it next time, you need input user name and password again.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

6. Appendix

6.1. Specification

6.1.1. Hardware

Item A2 GATEWAY

Adapter

(Input/Output) port WAN

LAN

Input: 100-240V

Output: 12V 1A

10/100Base- T RJ-45 for LAN

10/100Base- T RJ-45 for PC

Operation

Temperature

0 40

Relative Humidity

10 65% main chip

SDRAM

Ralink MIPS 24KEC (320MHz)

16M

Flash 4M

6.1.2. Voice features

z

Support SIP 2.0 (RFC3261) and correlative RFCs

z

Codec: G.711A/u, G.729a/b

B

G.726-32k

z

Echo cancellation: G.168 Compliance in LEC

z

Support Voice Gain Setting, VAD, CNG

z

NAT penetration, Support for STUN way through

z

SIP support SIP domain, SIP authentication(none basic, MD5), DNS name of server, Peer to Peer/ IP call

z

SIP can register two SIP accounts, through the Pubic Server / Private server, users can either account for inbound and outbound

z

Support call line automatically selected, when the public can not connect the server when the server can automatically switch to the private call

z

DTMF Relay: support SIP info

B

DTMF Relay

B

RFC2833

z

SIP application: SIP Call forward/transfer

>

blind/attended

?

/hold/waiting/3 way talking/

z

Call control features: Flexible dial map, hotline, empty calling No. reject service, black list for reject authenticated call, limit call, no disturb, caller ID, Flexible deer peer rule.

z

Support T.38 Fax

z

Add busy when N / A lines of the 4 modes

z

Support FXS2 and FXS2

6.1

.3. Network features

z

WAN/LAN: support bridge and router model

z

Support PPPoE for XDSL

z

Support DHCP server in the LAN port

z

Gateway ping test through keyboard commands

z

Support DHCP client in the WAN port

z

Support basic NAT and NAPT

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

z

Support VLAN (optional: voice vlan/ data vlan),support NTP

z

Support VPN (L2TP/PPTP) function

z

WAN Port supports main DNS and secondary DNS server can select dynamically to get

DNS in DHCP mode or statically set DNS address.

z

QoS with DiffServ

z

Support DNS relay, supports NTP Client, Firewall support the simple

z

Network tools in telnet server: including ping, trace route, telnet client

6.1.4. Maintenance and management

z

Support Safe Mode

z

Can be updated by safe Mode

z

Web ,telnet and keypad management

z

Management with different account right

z

Upgrade firmware through HTTP, FTP or TFTP Telnet remote management/ upload/download setting file

z

Support Syslog

z

Support Auto Provisioning (upgrade firmware or configuration file)

6.2. Particularly suitable for A2 two-port gateway

z

Service Provider of telecom operators and (ITSP) Internet Telephony

z

Large companies (for international and domestic long distance and / or internal communications, mainly in the way free sparring)

z

Import and export business of small or medium enterprises, such as foreign travel, study intermediary agents, immigration agents and other intermediaries

z

Foreign / joint ventures, foreign enterprises in China, offices, representatives and agents, etc.

z

Foreign hotel (which can be placed in the rooms and business center or leased)

z

All levels of government in dealing with foreigners more departments, such as foreign trade sector, the CPAFFC, sports units, cultural units, Foreign Experts Affairs, the foreign affairs department, etc.

z

Schools and research institutes, such as the joint venture school, school or Foreign

Affairs Department of the research unit.

z

IP supermarkets, IP telephone booth (mostly set in the migrant workers, students focus on areas such as low-income people)

z

Personal and home users, such as immigrant families, host families, student hostels, separation of individual family members due to long working relationship, often with family or friends living abroad keep in touch with the individuals.

6.3. Common Problems

Symptom

POWER light does not shine

WAN/LAN link light does not shine

Solution

1

Ú

Check the power connection is correct.

2

Ú

Check the power adapter is used.

1

Ú

indicator light is on.

2

Ú

Check the card is working properly, the specific approach is seen in the PC, there with "?" Or "!" Device under "Network Adapter". If so, remove the device and reinstall. Otherwise, the NIC in another slot, if not enough, replace the card.

47 http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

http://arttel.ru

Can not access the internet

Access modes commonly used example (already installed on your computer dial-up software)

Description:

1

Ú

Make sure the front of the problem does not exist.

2

Ú

Make sure that dial-up software is properly installed and set.

3

Ú

Sure to enter the correct user name and password.

4

Ú

If it does not work after the success dial up, make sure the

IE browser's proxy server is set correctly.

5

Ú

Please try to log multiple pages to confirm a Web server failure is not due.

http://arttel.ru/shop/voip-shlyuzy/golosovoj-shlyuz-fanvil-a2

48

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement