Quoizel DOR5015MB Doran 15-Light Mottled Black Candle-Style Chandelier Instructions

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

.

.

Assembly Instruction Sheet #IS-DOR5015MB

For Style DOR5015MB

Please go to www.quoizel.com

for product cleaning tips. Go to the Care + Maintenance selection.

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Light Source: (15) B10 Candelabra Base bulbs 60W Maximum, Candelabra Base T8 Vintage bulbs are recommended, bulbs not included.

Estimated Assembly Time: 20-30 minutes

Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement parts.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

A

Fixture Loop with Side Rods x 1

STEP 1 Install Fixture Loop with Side Rods, Upper Tier, Medium

Tier and Bottom Tier together

A. Attach side rods on the Bottom Tier (D) and side rods on the Top Tier

(B) to the loops in the Medium Rod (C).

B. Carefully pull supply wires and ground wire through the Fixture Loop with Side Rods (A) and attach side rods of Fixture Loop with Side

Rods (A) to loops in the Upper Tier (B).

B

Loop

Upper Tier x 1

B

Medium

Tier x 1

C

TOP VIEW

Side Rod

A

C

D

Supply Wires and

Ground Wire

Figure 1

AA

Crossbar

Assembly x 1

2018 QuoizelInc.

D

Bottom Tier x 1

Hardware Contents

B

Side Rod

Loop

Loop

BB

Fixture Chain x 1

CC

Quick Link x 2

DD

Ceiling

Canopy x 1

D

C

Side Rod

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.com

1of3

ReleasedDate:2018-03-02

STEP 2 Install the Crossbar Assembly to Outlet Box and Adjust the length of the Nipple

STEP 4 - Making the Wire Connections

A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head of the Green Ground Screw facing you. Secure it with Outlet Box

Screws (not included), tighten until snug .

B. Adjust the hex nut and lock washer underside of the crossbar to the middle of the nipple.

C. Remove the canopy lock ring from the canopy chain loop. Place the

Ceiling Canopy (DD) over the canopy chain loop against the ceiling to determine the correct position of the nipple. Thread the canopy lock ring onto the canopy chain loop. Adjust the nipple to allow the

Ceiling Canopy (DD) to rest against the ceiling when held in place by the canopy lock ring.

D. Remove the canopy lock ring and the Ceiling Canopy (DD). Tighten the lock washer and the hex nut against the crossbar to secure in place.

A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the

B.

green ground screw.

Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together.

Wrap each connection with approved electrical tape and carefully stuff all the connected wires into outlet box.

Note: If the electrical wire is going to be cut shorter than provided you will need to identify the "L" line wire and the "N" neutral wire before you cut the excess wire off. One is labeled N and the other labeled L. To do this separate the "L" line wire and the "N" neutral wire as far as you need to. Re-label the wire near where you want to make the cut. Be sure to mark the wire on the side of the fixture and not on the excess wire being cut and removed.

AA

Outlet Box Screw

(not included)

Hex Nut and

Lock Washer

Outlet Box

Green Ground Screw

Nipple

Canopy Chain Loop

White wire from outlet box

Black wire from outlet box (or Red)

Bare, or Green

Ground wire from outlet box

White wire from fixture identified with the Label “N”

Black wire from fixture identified with the label “L”

Ground wire from Fixture

DD Green Ground Screw on the Crossbar

Figure 4

Figure 2

Canopy Lock Ring

STEP 3 - Install the Fixture Chain and Ceiling Canopy

A. Adjust the Fixture Chain (BB) to your desired length by removing links if needed. Put a cloth over the Fixture Chain (BB) to protect the finish.

B. Pull the supply wires through the Fixture Chain (BB) alternating links. After the wires are through the Fixture Chain (BB), pull the

Supply Wires and the Ground Wire through the canopy lock ring and the Ceiling Canopy (DD) in order.

C. Attach one end of the Fixture Chain (BB) to the fixture loop with one

Quick Link (CC). Lift the fixture and Fixture Chain (BB) up and attach the other end of the Fixture

Chain (BB) onto the canopy chain loop with another Quick Link (CC).

The fixture will now hang safely.

D. Feed the Supply Wires and

Ground Wire through the canopy chain loop and nipple into the outlet box. Cut the wires leaving approximately 8” of wire

Supply Wires and Ground

Wire extending from the Outlet Box.

E. Go to Step 4 for wire connections and follow the directions. Return to Step F in this step when complete with Step 4.

F. Raise the Ceiling Canopy (DD) and canopy lock ring up the

Fixture Chain (BB) and over the canopy chain loop. Tighten the canopy lock ring onto the canopy chain loop until tight.

BB

Nipple

Canopy

Chain Loop

CC

CC

DD

Figure 3

Canopy

Lock Ring

Suggested chain length for

Ceiling height :

9’ ceiling : use 2 links of chain and

2 quick links

10’ ceiling : use 12 links of chain and 2 quick links

Fixture

Loop

STEP 5 - Install Bulbs

A. Insert bulbs onto the sockets and screw snugly into place.

Your fixture is now assembled and ready to use. Enjoy!

Figure 5

Socket

T8 Vintage Bulb

(recommended but not included)

2018 QuoizelInc.

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.com

2of3

ReleasedDate:2018-03-02

DOR5015MB

FINISH: MOTTLED BLACK

NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4

"

5” Dia.

142.5” OVERALL

HEIGHT INCLUDES

96” CHAIN AND

2 QUICK LINKS

)

40.75"

40.25” Dia.

2018 QuoizelInc.

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.com

3of3

ReleasedDate:2018-03-02