GOT-3840TL User`s Manual Version A1 JUN 2007F

GOT-3840TL
All-in-One
8.4” TFT SVGA Cost-effective Fanless
Touch Panel Computer
User’s Manual
i
Disclaimers
The information in this manual has been carefully checked and is believed to
be accurate. AXIOMTEK Co., Ltd. assumes no responsibility for any
infringements of patents or other rights of third parties, which may result from
its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may be
contained in this document. AXIOMTEK makes no commitment to update or
to keep current the information contained in this manual.
AXIOMTEK reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of
AXIOMTEK Co., Ltd.
©Copyright 2006 by AXIOMTEK Co., Ltd.
All rights reserved.
February 2006, Version A1
Printed in Taiwan
ii
Safety Approvals
‹
CE Marking
‹
FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for
help.
Shielded interface cables must be used in order to comply with
emission limits.ou
iii
Safety Precautions
Before getting started, read the following important cautions.
1. The GOT-3840TL does not come equipped with an operating
system. An operating system must be loaded first before
installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power cord from the GOT-3840TL before
making any installation. Be sure both the system and the
external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the GOT-3840TL
is properly grounded.
4. The brightness of the flat panel display decreases with usage.
However, hours of use vary depending on the application
environment.
5. Turn OFF the system power before cleaning. Clean the
system using a cloth only. Do not spray any liquid cleaner
directly onto the screen. The GOT-3840TL may come with or
w/o a touchscreen. Although the touchscreen is chemical
resistant, it is recommended that you spray the liquid cleaner
on a cloth first before wiping the screen. In case your system
comes without the touchscreen, you must follow the same
procedure and not spray any cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touchscreen.
Scratches on the touchscreen may cause malfunction or
internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or vibration.
When assembling the GOT-3840TL, make sure it is securely
installed.
iv
8. Do not open the system’s back cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to
do so. Integrated circuits on computer boards are sensitive to
static electricity. To avoid damaging chips from electrostatic
discharge, observe the following precautions:
9 Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few seconds.
This will help to discharge any static electricity on your body.
9 When handling boards and
wrist-grounding strap, available
component stores.
components,
from most
wear a
electronic
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks of
Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties of their
respective owners.
v
This page does not contain any information.
vi
Table of Contents
Disclaimers........................................................................... ii
Safety Approvals................................................................iii
Safety Precautions ............................................................. iv
Chapter
1 .....................................................................1
Introduction ..........................................................................1
1.1 General Description ................................................1
1.2 Specifications ..........................................................2
1.2.1
1.2.2
1.2.3
Main CPU Board ...................................................... 2
I/O System ............................................................... 2
System Specification .............................................. 3
1.3 Dimensions ..............................................................4
1.4 I/O Outlets ................................................................4
1.4 I/O Outlets ................................................................5
1.5 Package List ............................................................6
Chapter
2 .....................................................................7
Hardware Installation.........................................................7
2.1 HDD Installation ......................................................7
2.2 CF card Installation.................................................9
2.3 Wireless Card Installation ....................................10
2.4 3 x Serial Ports ......................................................13
2.5 VGA ........................................................................15
2.6 Ethernet..................................................................15
2.7 Mountings: Panel / Wall / Desktop / VESA ..........16
2.7.1 VESA-ARM/Wall-Mount ........................................... 16
2.7.2 Desktop Kit Assembly ............................................. 17
2.7.3 Panel-mount Kit Assembly ..................................... 17
C h a p t e r 3 ......................................................................18
Driver Installation .............................................................18
3.1 Touch Screen ........................................................19
Table of Contents
vii
3.1.1 Driver Installation- Windows 2000/XP .................... 19
3.2 Embedded O.S. ........................................................22
3.2.1 Windows XP Embedded.......................................... 22
3.2.2 Windows CE.NET 5.0 ................................................ 23
viii
Table of Contents
GOT-3840TL User’s Manual
Chapter
1
Introduction
This chapter contains the general information and the detail
specifications of the GOT-3840TL. Chapter 1 includes the following
sections:
„
„
„
1.1
General Description
System Specification
Dimensions
„
„
„
I/O Outlets
Utilities Supported
Package List
General Description
The GOT-3840TL is a fan-less and compact-size touch panel
computer, and is equipped with a 8.4" TFT LCD display and low
power consumption CPU, AMD LX800 processor 500MHz. The
GOT-3840TL supports Windows® XP, Windows® CE.NET,
Windows® XP embedded. The panel is able to install in a
CompactFlash™ card and provides a MiniPCI slot for wireless
module.
„
GOT-3840TL: 8.4” TFT Cost-effective SVGA Fanless Touch
Panel Computer
Reliable and Stable Design
The GOT-3840TL adopts a fan-less cooling system and a
CompactFlash™ card, which makes it especially suitable for
vibration-heavy environments, best for the transportation, ship, and
industrial machinery markets.
Embedded O.S. Supported
The GOT-3840TL not only supports Windows® XP, but also supports
embedded OS, such as Windows® CE.NET, and Windows® XP
embedded. For storage device, the GOT-3840TL supports 2.5" HDD
or CompactFlash™ card.
Industrial-grade Product Design
The GOT-3840TL has an incredible design that can be used in
Introduction
1
GOT-3840TL User’s Manual
different industrial harsh environments.
„
„
A fuse helps prevent over-voltage for power input.
Stainless steel back chassis and Aluminum front bezel meets
the IP65/NEMA4 standard.
For connecting other devices, the GOT-3840TL also features
several interfaces: USB, Ethernet, and RS-232/422/485.
„
1.2
1.2.1
Specifications
Main CPU Board
„ CPU: AMD LX800 processor 500MHz onboard.
„ System Chipset: CS5536AD
„ BIOS: Award 4Mbit with RPL/PEX LAN boot ROM,
SmartView and customer CMOS backup.
„ System Memory: One 200-pin DDR DIMM socket.
Maximum up to 1GB
1.2.2
I/O System
„ Standard I/O:
− 3 x serial ports
− 2 x RS-232,
1 x RS-232/422/485
− 2 x USB 2.0
2
Introduction
GOT-3840TL User’s Manual
„ Ethernet:
- RJ45 x2
„ Expansion Slot:
- MiniPCI for wireless module
„ Audio(Line out)
1.2.3
„
„
„
Net weight:
−
„
System Specification
8.4” TFT LCD
Heat dispensing design
1.8 Kg
Dimension (main body size):
− 280x69.3x200mm
„
„
„
Operating temperature: O° to 50°C ; Relative
umidity:40%
Relative humidity: 10% to 90% @ 40° C, on-condensing
Vibration (operating):
5 to 500 Hz, 1.3 G random ( install HDD )
5 to 500 Hz, 2.0 G random ( install CompactFlash card )
3
GOT-3840TL User’s Manual
1.3
Dimensions
The following diagrams show the dimensions and outlines of
GOT-3840TL
260.3
200.0
6.0
69.3
180.3
280.0
4
63.3
GOT-3840TL User’s Manual
1.4
I/O Outlets
The following figure shows the I/O locations of the GOT-3840TL. Most
of the I/O connectors are located on the back panel of the
GOT-3840TL
1
2
3
4
5
6
7
8
1:
Power connector
6:
PS2 keyboard/mouse
2:
COM
7:
1 X Ethernet (RJ45)
3:
Audio(Line out)
8:
VGA
4:
2 X USB2.0
5:
1 X Ethernet (RJ45)
5
GOT-3840TL User’s Manual
1.5
Package List
When you receive the GOT-3840TL there are following items in the
package. If you can not find it, please contact AXIOMTEK distributors.
1. GOT-3840TL x 1
2. Panel mount kit x 6
3. CD driver x1
4. Desktop kit x 2 (optional)
5. VESA ARM/Wall-mount kit(optional)
6
GOT-3840TL User’s Manual
Chapter
2
Hardware Installation
The GOT-3840TL provides lots of flexible ways for you to select
different configuration such as HDD, CF card and more. The chapter
will show you how to install the hardware. It includes:
2.1
HDD Installation
The GOT-3840TL offers a convenient drive bay module for users to
install HDD. The GOT-3840TL offers one 2.5” HDD drive for users to
install. Please follow the steps:
1. Take out the, HDD bracket kit, 4 anti-vibration screws, 4
anti-vibration rubbers and 4 bracket screws from the accessory
package.
2. Screw 4 anti-vibration screws and fix HDD on the bracket kit.
7
GOT-3840TL User’s Manual
3. Fix the HDD kit to system by 4 screws.
8
GOT-3840TL User’s Manual
2.2
CF card Installation
The GOT-3840TL offers a slot for users to install CF card. When
installing the CF card, refer to the following instructions and
illustration:
1. Open the back cover. Find SBC84621 and turn to back side.
2. Install user’s CF card.
9
GOT-3840TL User’s Manual
2.3
Wireless Card Installation
The GOT-3840TL provides one miniPCI slot for user to install one
wireless card. When installing the wireless card, refer to the following
instructions and illustration:
1. Open the back cover and find SBC84621.
10
GOT-3840TL User’s Manual
2. Install MiniPCI wireless card.
3. Connect cable from antenna to wireless card..
11
GOT-3840TL User’s Manual
12
GOT-3840TL User’s Manual
2.4
3 x Serial Ports
The connector, COM 1, is a DB-9 connector, and the following table
shows the pin assignments of this connector.
COM1 Port Connectors
Pin
Signal Name
1
DCD, Data carrier detect
2
RXD, Receive data
3
TXD, Transmit data
4
DTR, Data terminal ready
5
GND, ground
6
DSR, Data set ready
7
RTS, Request to send
8
CTS, Clear to send
9
RI, Ring indicator
COM1
COM2 Port Connectors: CN12
The RS-232 pin assignments are listed on the following table.
Pin
Description
1
Data
Carrier
(DCD)
3
Pin
Detect
Description
2
Data Set Ready (DSR)
Receive Data (RXD)
4
Request to Send (RTS)
5
Transmit Data (TXD)
6
Clear to Send (CTS)
7
Data Terminal
(DTR)
8
Ring Indicator (RI)
9
Ground (GND)
10
NC
Ready
CN12
1
2
3
4
5
6
7
9
8
10
13
GOT-3840TL User’s Manual
The RS-422/485 pin assignments for COM2/COM4 are listed
below.
Pin
Signal
Pin
Signal
1
NDCD2
11
NDCD4
2
NDSR2
12
NDSR4
3
NRX2
13
NRX4
2
4
NRTS2
14
NRTS4
1
5
NTX2
15
NTX4
6
NCTS2
16
NCTS4
7
NDTR2
17
NDTR4
8
NRI2
18
NRI4
9
GND
19
GND
10
N.C
20
N.C
Pin #
14
20
19
Signal Name
RS-422
RS-485
1
TX-
DATA-
2
TX+
DATA+
3
RX+
No connector
4
RX-
No connector
5
No connector
No connector
6
No connector
No connector
7
No connector
No connector
8
No connector
No connector
9
GND
GND
GOT-3840TL User’s Manual
2.5
VGA
The GOT-3840TL has an analog RGB interface connector. It is able to
connect to an expansion CRT monitor, and the system can display on
both the flat panel and the CRT simultaneously.
2.6
Ethernet
Ethernet RJ-45 Connector: LAN1
The GOT-3840TL is equipped with a high performance Plug and Play
Ethernet interface which is fully compliant with the IEEE 802.3
standard, and consisting of a RJ-45 connector LAN
3 . 4.15.1 Pin Assignment
LAN1: RJ-45 Connector Pin Assignment
Pin
Signal
1
Tx+ (Data
positive
transmission
2
Tx- (Data
negative)
transmission
3
Rx+(Data
positive)
4
RJ45 termination
5
RJ45 termination
6
Rx(Data
negative)
7
RJ45 termination
8
RJ45 termination
reception
reception
1 2 3 4 5 6 7 8
RJ-45
15
GOT-3840TL User’s Manual
2.7 Mountings: Panel / Wall / Desktop /
VESA
There are 4 application options for the GOT-3840TL,
Panel/Wall/Desktop/VESA mountings.
2.7.1 VESA-ARM/Wall-Mount
The GOT-3840TL provides two ways for VESA mount: 75x75 mm.
Screw four screws to fix the kit (optional) in the side chassis.
16
GOT-3840TL User’s Manual
2.7.2 Desktop Kit Assembly
The GOT-3840TL is designed for desktop application. Screw 4 screws
to fix the kit (optional) in the side chassis.
2.7.3 Panel-mount Kit Assembly
The GOT-3840TL is designed for panel mount application. To mount
the GOT-3840TL, the standard set of mounting kit (included in the
system packaging) is needed.
17
GOT-3840TL User’s Manual
C h a p t e r 3
Driver Installation
GOT-3840TL3108 could support with Windows 2000/XP. To facilitate
installation system driver, you should read the instructions in this
chapter carefully before you attempt installation.
1.
Insert Driver CD and select the “\GOT-3840TL Driver CD\”.
2.
Select all files and follow the install procedure.
18
GOT-3840TL User’s Manual
3.1 Touch Screen
Specification(GOT-3840TL)
Touch Screen:
For 5-wire analog resistive type
Touch Screen Controller:
Penmount 9036BH
Communications:
RS-232
Contact bounce:
< 15ms
Power Input:
5.5V DC or less
Power Consumption:
20mA (maximum)
Board Size:
174.8x132.2 mm
Operating Temperature:
-10℃ ~ 60℃ Humidity less than 85% RH
3.1.1 Driver Installation- Windows XP
The touch screen of GOT-3840TL provides a driver for use with
Windows 2000/XP. To facilitate installation of the touch screen driver,
you should read the instructions in this chapter carefully before you
attempt installation.
1.
Insert Driver CD and select the “\GOT-3840TL Driver
CD\Penmount\Serial\Driver\Windows2000-XP\Setup.exe”
19
GOT-3840TL User’s Manual
2.
Follow the install procedure and press OK.
3.
Click Start menu and select “PenMount Utilities”. You can see
PenMount Control Panel
20
GOT-3840TL User’s Manual
4.
Select the “Standard Calibrate” tab
5.
Calibration:
21
GOT-3840TL User’s Manual
To adjust the display with touch panel, click “Calibration” and follow
the calibrate point to do calibration; there are five points on screen for
calibration.
6.
Press OK.
3.2 Embedded O.S.
3.2.1 Windows XP Embedded
Supported onboard devices are as follows:
„
„
Onboard Multi I/O
Floppy drive
16C550 UARTs compatible serial port
IrDA for wireless communication
Onboard IDE
IDE HDD
USB
„
PS2 Keyboard and mouse
„
CRT/LCD display(Default 18bits Resolution 800x600)
„
10/100 base-T Ethernet
„
Compact flash
„
Onboard audio
„
Audio
„
22
GOT-3840TL User’s Manual
„
Touch Screen
PenMount Touch screen
GOT-3840TL has Penmount touch screen on COM3, which is
disabled by default.
Before you can use and calibrate it, you should :
1. Set up Penmount touch device driver by executing
c:\Penmount\ Windows 2000-XP V5.0\setup.exe. When
installation finished, an icon “PM” appears on Taskbar .
2. Calibrate Penmount touch by clicking on “PM” icon and
doing calibration
3. Restart computer.
3.2.2 Windows CE.NET 5.0
Supported onboard devices are as follows:
„
„
Onboard Multi I/O
Floppy drive
16C550 UARTs compatible serial port
IrDA for wireless communication
Onboard IDE
IDE HDD
USB
„
PS2 Keyboard and mouse
„
CRT/LCD display
„
10/100 base-T Ethernet
„
Compact flash
„
Onboard audio
„
Audio
„
Touch Screen
„
Calibration Touch Screen
In this image we add PenMount Touch drivers and utilities. It is
customized for 800 x 600.
Calibration:
23
GOT-3840TL User’s Manual
1. Click “Calibration” on desktop to calibrate touch
screen.
2. In the start\programs menu, select “save registry”,
thus Calilbration data will be saved and effective in
next boot.
24