DELTA MINI - DELTA Shotcrete, Gunite, Refractory Spraying and

DELTA MINI
GUNITE & REFRACTORY SPRAYING
MACHINE
PARTS & USER'S MANUAL
Delta Ltd
Dolapdere San. Sit. 20. Ada No:18
İkitelli, İstanbul
++90- (212) - 5498232
www.shotcreter.com
info@shotcreter.com
DELTA MINI
Shotcrete – concrete repair & refractory spraying machine
CAPACITY *
1-4 m3/saat
AIR
CONSUMPTION**
4-7 m3/dak
ELECTRICAL
MOTOR
3 Kw
VOLTAGE
380 V 50 Hz
HOSE SIZE
35 / 40 / 50 mm
DIMENSIONS
(mm)
1400 x 920 x 1350
WEIGHT (kg)
400-450
* DEPENDS ON ROTOR
** DEPENDS ON ROTOR, HOSE LENGTH,
MATERIAL HUMIDITY, etc.
OPTIONAL COMPONENTS
AUTOMATIC GLYCERINE LUBRICATION
HYDRAULIC CLAMPING
OUTPUT ADJUSTMENT
AIR MOTOR
DIESEL MOTOR
DELTA MAKINA LTD
Dolapdere Sanayi Sitesi 20. Ada No:18 Ikitelli , Istanbul 34670
TEL : (212) – 5498232 / 5498346 FAX: (212) – 5498357
www.shotcreter.com
info@shotcreter.com
DELTA MINI
Concrete repair and refractory spraying
applications
DELTA MAKINA LTD
Dolapdere Sanayi Sitesi 20. Ada No:18 Ikitelli , Istanbul 34670
TEL : (212) – 5498232 / 5498346 FAX: (212) – 5498357
www.shotcreter.com
info@shotcreter.com
PREPERATION AND USE OF THE SHOTCRETE MACHINE:
1. Connect the air compressor hose, make sure you use
a minimum 1 ¼” ID air hose and 6-7 cum/ min 7 bar air
compressor.
2. Connect the material hose.
3. Connect electrical power ( 3 x 380 V 50 Hz 4 kw)
4. Make sure the machine is properly grounded
5. Tighten the four clamping devices , first tighten all
four equally , then retighten the two near the air inlet.
6. Make sure the Emergency Buttons are not pressed,
and open the air solenoid by turning switch 2 to the
first position.( Make sure the nozzle operator is
holding the nozzle firmly)
7. Check the air coming out of the nozzle , adjust as
necessary
8. Turn on water and adjust from the nozzle valve.
9. Turn the switch 2 to the 2nd position, now the rotor is
ready to turn.
10. Pump a few strokes of glycerine to lubricate the
plates.
11. Push the “Increase speed” buton to start the rotor
12. Start filling material to the hopper
13. Observe the material coming out of the nozzle, adjust
air and water as necessary.
14. Start shotcreting , adjust air, water and the capacity
of the machine as necessary.
15. When done , first bring bacj switch 2 to position 1 and
wait untill the material hose is empty , turn off the
water supply then turn switch 2 to “0” position to stop
the air.
16. Now you are ready to clean and inspect the machine.
DELTA MINI SHOTCRETE MACHINE SPARE PARTS
DELTA MINI OUTLET SYSTEM AND NOZZLES
OUTLET VICE
OUTLET ELBOW
OUTLET ELBOW RUBBER INSERT
50 MM ID CONICAL OUTLET PIPE
50 mm ID CONICAL RUBBER INSERT
40 MM ID CONICAL OUTLET PIPE
40 mm ID CONICAL RUBBER INSERT
50 mm NOZZLE PIPE
40 mm NOZZLE PIPE
50 mm REFRACTORY NOZZLE
40 mm REFRACTORY NOZZLE
DELTA MINI GLYCERINE LUBRICATION SYSTEM
STANDARD MANUAL PUMP
OPTIONAL AUTOMATIC LUBRICATION SYSTEM
MANIFOLD ASSEMBLY
RUBBER PLATE LUBRICATION NIPPLES
REMOTE CONTROL & MAIN PANEL SWITCHES & BUTTONS & THEIR
FUNCTIONS
1) 4 KW FUSE
2) 2 AMP FUSE
3) 1 AMP FUSE
4) 1 AMP FUSE
5) 4 KW VFD
6) RELAY
7) 2 X 12 V XFORMER
8) BRIDGE RECTIFIER
9) E. CAPACITOR
10) CAPACITOR
INSIDE VIEW OF THE DELTA MINI ELECTRICAL PANEL
PLEASE INQUIRE WITH FIGURE NUMBERS/& /OR DESCRIPTION AND TAG DATA
DELTA MINI ELECTRICAL POWER CIRCUIT
EXPLODED VIEW OF THE DELTA MINI TRANSMISSION
PLEASE INQUIRE WITH FIGURE ITEM NUMBERS