VSP 112W
User Manual
 Manual #: RGB-RD-UM-V112W E002
 Revision: V1.5
VSP 112W
User Manual
1
VSP 112W·User Manual
Thank you for choosing our products!
In order to allow you to learn how to use the video processor quickly, we
bring you the detailed user manual. You can read the introduction and
directions before using the video processor, please read all the information
we provide carefully to use our products correctly.
Copyright
©2012 All rights are reserved by RGBLINK.
This document is done independently by Xiamen RGBlink Science &
Technology Co.,LTD. No part can be copied, reproduced or translated
without permission.
Notice
RGBlink provides this manual ―as is‖ without warranty of any kind, no
matter expressed or implied, including but not limited to the implied
warranties or merchantability and fitness for a particular purpose. RGBlink
may make improvements or changes to the products and the programs
described in this publication at any time without notice.
This publication would contain technical inaccuracies or typographical
errors. Changes are periodically made to the information in this publication;
these changes are incorporated in new editions of this publication.
Federal Communications Commission
(FCC) Statement
This equipment has been tested and found to comply with the limits for a
class A digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses and radiates radio frequency energy and, if not
installed or used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment
in a residential area may cause harmful interference, in which case the
user will be responsible for correcting any interference.
VSP 112W
User Manual
2
Guarantee and Compensation
RGBlink provides a guarantee related to perfect manufacturing as part
of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred
during transportation, as well as for material and manufacturing faults.
Please complain to RGBlink by written notice.
The period of guarantee begins from the date of transfer of risks, in the
case of special systems and software on the date of commissioning, at
latest 30 days after the transfer of risks. In the event of justified notice of
compliant, RGBlink can repair the fault or provide a replacement at its own
discretion within an appropriate period. If this measure proves to be
impossible or unsuccessful, the purchaser can demand a reduction in the
purchase price or cancellation of the contract. All other claims, in particular
those relating to compensation for direct or indirect damage, and also
damage attributed to the operation of software as well as to other service
provided by RGBlink, being a component of the system or independent
service, will be deemed invalid provided the damage is not proven to be
attributed to the absence of properties guaranteed in writing or due to the
intent or gross negligence or part of RGBlink.
If the purchaser or a third party carries out modifications or repairs on
goods delivered by RGBlink, or if the goods are handled incorrectly, in
particular if the systems are commissioned operated incorrectly or if, after
the transfer of risks, the goods are subject to influences not agreed upon in
the contract, all guarantee claims of the purchaser will be rendered invalid.
Not included in the guarantee coverage are system failures which are
attributed to programs or special electronic circuitry provided by the
purchaser, e.g. interfaces. Normal wear as well as normal maintenance are
not subject to the guarantee provided by RGBlink either.
The environmental conditions as well as the servicing and maintenance
regulations specified in this manual must be complied with the customer.
Trademark
Brand and product names mentioned in this manual may be trademarks,
registered trademarks or copyrights of their respective holders. All brand
and product names mentioned in this manual serve as comments or
examples and are not to be understood as advertising for the products or
their manufactures.
VSP 112W
User Manual
3
Company Address
Xiamen RGBlink Science & Technology Co., Ltd.
Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial
Development Zone Xiamen, Fujian Province, P.R.C
Shenzhen office: Floor 11, A1 Building, Baiwang R&D Building,
Shahe West Road, Xili Town, Nanshan District, Shenzhen,
Guangdong Province, P.R.C
Beijing office: Room 602, Building 7, CaiManJie, No.67 Chaoyang
Road, Chaoyang District, Beijing, P.R.C
Shanghai office: Building 3, 1358 Nong, Tongpu Road, Shanghai,
P.R.C





VSP 112W
Tel: +86-592-5771197
Fax: +86-592-5771202
Customer Hotline:4008-592-315
Websites:
~ http://www.rgblink.com
~ http://www.rgblink.cn
E-mail:rgblinkcs@gmail.com
User Manual
4
Operators Safety Summary
The general safety information in this summary is for operating personnel.
Do Not Remove Covers or Panels
There are no user-serviceable parts within the unit. Removal of the top
cover will expose dangerous voltages. To avoid personal injury, do not
remove the top cover. Do not operate the unit without the cover installed.
Power Source
This product is intended to operate from a power source that will not apply
more than 230 volts rms between the supply conductors or between both
supply conductor and ground. A protective ground connection by way of
grounding conductor in the power cord is essential for safe operation.
Grounding the Product
This product is grounded through the grounding conductor of the power
cord. To avoid electrical shock, plug the power cord into a properly wired
receptacle before connecting to the product input or output terminals. A
protective-ground connection by way of the grounding conductor in the
power cord is essential for safe operation.
Use the Proper Power Cord
Use only the power cord and connector specified for your product. Use only
a power cord that is in good condition. Refer cord and connector changes
to qualified service personnel.
Use the Proper Fuse
To avoid fire hazard, use only the fuse having identical type, voltage rating,
and current rating characteristics. Refer fuse replacement to qualified
service personnel.
Do Not Operate in Explosive
Atmospheres
To avoid explosion, do not operate this product in an explosive
atmosphere.
VSP 112W
User Manual
5
Terms in This Manual and Equipment
Marking
WARNING
Highlight an operating procedure, practice, condition,
statement, etc, which, if not strictly observed, could result in
injury or death of personnel.
Note
Highlights an essential operating
procedure, condition or statement.
CAUTION
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
VSP 112W
User Manual
6
Amendment Records
The table below lists the changes to the Video Processor User Manual.
Format
Time
ECO#
V1.0
2011-12-21
0000
Release
BIN
V1.1
2012-10-12
0001
Change the output interface.
BIN
V1.2
2013-02-01
0002
Update the user manual format.
BIN
V1.3
2013-07-01
0003
1. Menu update.
2. Change the Back and front Panel.
3. Update Software.
4. Add program editing function.
Vira
V1.4
2013-08-10
0004
1. Change the product name.
2. Change the Back and front Panel.
3. Add ―Supported 3G USB Adaptor,
WIFI and VPN router List‖.
4. Add Brightness&Temperatures
Sensor Specification.
Vira
V1.5
2013-08-10
0005
1.Add USB1 and USB2 prioritize
function-p27
2.Add SD card and USB prioritize
function- P27
3.Add How to Connect PC Through
LAN Interface?-p73
peter
VSP 112W
Description
User Manual
Principal
7
CONTENT
CONTENT .......................................................................................... 8
1. Brief Introduction....................................................................... 14
Chapter Structure ............................................................................. 15
How to Use the Manual ................................................................... 16
Term and Definitions ........................................................................ 17
System Overview ............................................................................. 23
Application Questions ......................................................................... 24
2. Hardware Orientation ................................................................ 25
In This Chapter ................................................................................. 25
VSP 112W Back Panel .................................................................... 26
CONT Interface ........................................................................................ 26
11. 10/100M Interface RJ45 ................................................................... 26
12. RS232 Interface ................................................................................. 26
INPUT Interface ........................................................................................ 26
13:USB Input.......................................................................................... 26
14:SD Card Input .................................................................................. 27
17:DVI Input ........................................................................................... 27
18:VGA Input.......................................................................................... 28
OUTPUT .................................................................................................... 28
VSP 112W
User Manual
8
1.2.6.7: 10/100M Interface RJ45 ........................................................... 28
3. 8:Power Supply Port of Sending Card .......................................... 28
4. 9:USB Control Port of Sending Card ............................................. 28
5. 10:DVI Input ....................................................................................... 28
19:AUDIO Output .................................................................................. 28
20:DVI Output ........................................................................................ 28
21:DVI +VGA DVI Output .................................................................... 28
Switch and Power .................................................................................... 29
22.23:Power Interface and Switch ..................................................... 29
VSP 112W Front Panel ................................................................... 30
LCD Panel ................................................................................................. 32
Signal Keys ............................................................................................... 32
Function Keys ........................................................................................... 32
3. Hardware Installation ................................................................ 34
In This Chapter ................................................................................. 34
Safety Precautions ........................................................................... 35
Unpacking and Inspection ............................................................... 35
Site Preparation ................................................................................ 35
4. Menu Orientation ....................................................................... 36
In This Chapter ................................................................................. 36
MENU ................................................................................................ 37
VSP 112W
User Manual
9
MENU---INPUT ........................................................................................ 39
MENU ---OUTPUT ................................................................................... 39
MENU --- TRANSITION .......................................................................... 45
MENU --- AUDIO ...................................................................................... 47
MENU --- SPLIT ....................................................................................... 47
MENU --- SAVE SETUP ......................................................................... 47
MENU --- SYSTEM .................................................................................. 48
MENU --- LANGUAGE ............................................................................ 48
MENU --- FACTORY RESET ................................................................. 49
5. Communication Software Guideline ....................................... 50
In This Chapter ................................................................................. 50
Software Installation ......................................................................... 51
Software Operation .......................................................................... 55
Connection ................................................................................................ 55
Use ............................................................................................................. 58
File Toolbar ................................................................................................ 58
Communication Toolbar .......................................................................... 60
Device Toolbar .......................................................................................... 61
Schedule Toolbar ..................................................................................... 62
Help Toolbar .............................................................................................. 63
Output Resolution Toolbar ...................................................................... 63
Images Display Mode Toolbar................................................................ 63
VSP 112W
User Manual
10
Layout Toolbar .......................................................................................... 63
Aspect Ratio Toolbar ............................................................................... 64
Signal Input Toolbar ................................................................................. 64
Screen Parameter Toolbar...................................................................... 65
Image Toolbar ........................................................................................... 65
Display Toolbar ......................................................................................... 65
Output Image Setup Toolbar .................................................................. 66
Images Display Toolbar ........................................................................... 66
User Mode Toolbar .................................................................................. 67
Log Toolbar ............................................................................................... 67
Information Toolbar .................................................................................. 67
[Video Processor] Options ...................................................................... 67
[Help] Options ........................................................................................... 72
How to Connect PC Through LAN Interface ................................. 73
6. System Setup and Operations ................................................. 77
In This Chapter ................................................................................. 77
Interface and Input Signal Option ................................................... 78
How to Confirm the Device is in Normal Operation...................... 81
How to Choose the Language on the LCD ................................... 83
How to Adjust the Output Resolution ............................................. 84
How to Realize Single Image Switching ........................................ 85
How to Set Up the Size and Position of the Single Image .......... 86
VSP 112W
User Manual
11
How to Realize the Screen Size and Full Size Switching ............ 87
How to Edit the Program ................................................................. 88
How to Set Router VPN ................................................................. 105
How to Save the Parameter .......................................................... 111
How to Load the Saved Parameter .............................................. 112
Usage of SD Card and USB ......................................................... 113
7. Common Questions and Solutions ...................................... 118
In This Chapter ............................................................................... 118
No Output in LED Display ............................................................. 119
Confirm If There is Any Input Signal ................................................... 119
Confirm If Signal Output ....................................................................... 119
Flash Point in LED Display Output ............................................... 119
Confirm If Monitor Output is Normal ................................................... 119
LED Display Only Displays Part of the Image ............................ 120
Signal Needs to Scale ........................................................................... 120
No Display in the Second Half Part of LED Display ................... 120
Resolution is Insufficient ....................................................................... 120
Sending Card Can not Take Lower Part............................................. 120
Left Screen Appears Two Black Sides ......................................... 120
Adjust DE Deviation ............................................................................... 120
A. Specification ............................................................................ 121
VSP 112W
User Manual
12
Supported 3G USB Adaptor, WIFI and VPN Router List ...... 123
SER510R/T Brightness&Temperatures Integration Sensor
Specification ................................................................................. 124
B. Contact Information .................................................................127
C. Sending Card Wire Bonding Steps ...................................... 128
VSP 112W
User Manual
13
1. Brief Introduction
This chapter is designed to introduce you to the VSP 112W User Manual.
Areas to be covered are:

Chapter Structure

How to Use The Manual

Terms and Definitions

System Overview

Application Questions
VSP 112W
User Manual
14
1. Brief Introduction
Chapter Structure
Chapter Structure
The following chapters provide instructions for all aspects of VSP 112W
operations.
Chapter 1 Brief Introduction
Chapter 2 Hardware Orientation
Chapter 3 Hardware Installation
Chapter 4 Menu Orientation
Chapter 5 Communication Software Guideline
Chapter 6 System Setup and Operations
Chapter 7 Common Questions and Solution
Appendix A
Specification
Appendix B
Contact Information
Appendix C
Sending Card Wire Bonding Steps
VSP 112W
User Manual
15
1. Brief Introduction
How to Use The Manual
How to Use the Manual
Followings are important tips for streamlining your use of this User Manual
in its electronic ―PDF‖ form.
Navigation
Use Acrobat Reader’s ―bookmarks‖ to navigate to the desired location. All
chapter files have the same bookmark structure for instant navigation to
any section. Please note:
 Extensive hyperlinks are provided within the chapters.
 Use Acrobat’s ―Go to Previous View‖ and ―Return to next View‖
buttons to trace your complete navigational path.
 Use the ―Previous Page‖ and ―Next Page‖ buttons to go to the previous
or next page within a file.
 Use Acrobat’s extensive search capabilities, such as the ―Find‖ tool and
―Search Index‖ tool to perform comprehensive searches as required.
Table of Contents and Index
Use the Table of Contents bookmarks to navigate a desired topic.
Click any item to instantly jump to that section of the guide. You can
also use the Index to jump to specific topics within a chapter. Each
page number in the Index is a hyperlink.
General Operations
To ensure trouble-free operation, please follow all procedures as listed
below:
 For detailed installation instructions, refer to chapter 3 ―Hardware
Installation‖ on page 33.
 For communication software control guide, refer to Chapter 5,
―Communication Software Control Guide‖ on page 49.
 For system setup and operations, refer to Chapter 6, ―System Setup
and Operations‖ on page 74.
Should you have any questions regarding the installation or
operation of VSP 112W, please consult with the factory. Refer to
Appendix B ―Contact information‖ on page 119.
VSP 112W
User Manual
16
1. Brief Introduction
Terms and Definitions
Term and Definitions
The following terms and definitions are used throughout this guide.
 “ASCII”: American Standard for Information Interchange. The standard
code consisting of 7-bit coded characters (8 bits including parity check)
used to exchange information between data processing systems, data
communication systems, and associated equipment. The ASCII set
contains control characters and graphic characters.
 “Aspect ratio”: The relationship of the horizontal dimension to the
vertical dimension of an image. In viewing screens, standard TV is 4:3,
or 1.33:1; HDTV is 16:9, or 1.78:1. Sometimes the ―:1‖ is implicit,
making TV = 1.33 and HDTV = 1.78.
 “AV”: Audio visual or audio video.
 A “Background” is an unscaled source, typically originating from a
computer. A background source appears at the system’s lowest priority
— visually in back of all other sources.
 “Baudrate”:Named of J.M.E. Baudot, the inventor of the Baudot
telegraph code. The number of the electrical oscillations per second,
called baud rate. Related to, but not the same as, transfer rate in bits
per second (bps).
 “Blackburst”: The video waveform without the video elements. It
includes the vertical sync, horizontal sync, and the chroma burst
information. Blackburst is used to synchronize video equipment to
align the video output. One signal is normally used to set up an entire
video system or facility. Sometimes it is called House sync.
 “BNC”: Bayonet Neill-Concelman. A cable connector used extensively
in television and named for its inventors. A cylindrical bayonet
connector that operates with a twist-locking motion. To make the
connection, align the two curved grooves in the collar of the male
connector with the two projections on the outside of the female collar,
push, and twist. This allows the connector to lock into place without
tools.
 “Brightness”: Usually refers to the amount or intensity of video light
produced on a screen without regard to color. Sometimes called ―black
level.
 ―CAT 5‖: Category 5. Describes the network cabling standard that
consists of four unshielded twisted pairs of copper wire terminated by
RJ-45 connectors. CAT 5 cabling supports data rates up to 100 Mbps.
CAT 5 is based on the EIA/TIA 568 Commercial Building
Telecommunications Wiring Standard.
 “Color bars”: A standard test pattern of several basic colors (white,
yellow, cyan, green, magenta, red, blue, and black) as a reference for
system alignment and testing. In NTSC video, the most commonly
VSP 112W
User Manual
17
1. Brief Introduction
Terms and Definitions
 Used color bars are the SMPTE standard color bars. In PAL video, the
most commonly used color bars are eight full field bars. In the
computer, the most commonly used color bars are two rows of
reversed color bars.
 “Color burst”: In color TV systems, a burst of sub carrier frequency
located on the back porch of the composite video signal. This serves
as a color synchronizing signal to establish a frequency and phase
reference for the chroma signal. Color burst is 3.58 MHz for NTSC and
4.43 MHz for PAL.
 “Color temperature”: The color quality, expressed in degrees Kelvin
(K), of a light source. The higher the color temperature, the bluer the
light. The lower the temperature, the redder the light. Benchmark color
temperature for the A/V industry includes 5000°K, 6500°K, and
9000°K.
 “Contrast ratio”: The radio of the high light output level divided by the
low light output level. In theory, the contrast radio of the television
system should be at least 100:1, if not 300:1. In reality, there are
several limitations. In the CRT, light from adjacent elements
contaminate the area of each element. Room ambient light will
contaminate the light emitted from the CRT. Well-controlled viewing
conditions should yield a practical contrast ratio of 30:1 to 50:1.
 “DVI”: Digital Visual Interface. The digital video connectivity standard
that was developed by DDWG (Digital Display Work Group). This
connection standard offers two different connectors: one with 24 pins
that handles digital video signals only, and one with 29 pins that
handles both digital and analog video.
 “EDID”: Extended Display Identification Data – EDID is a data structure
used to communicate video display information, including native
resolution and vertical interval refresh rate requirements, to a source
device. The source device will then output the optimal video format for
the display based on the provided EDID data, ensuring proper video
image quality. This communication takes place over the DDC –
Display Data Channel.
 “Ethernet”: A Local Area Network (LAN) standard officially known as
IEEE 802.3. Ethernet and other LAN technologies are used for
interconnecting computers, printers, workstations, terminals, servers,
etc. within the same building or campus. Ethernet operates over
twisted pair and over coaxial cable at speeds starting at 10Mbps. For
LAN interconnectivity, Ethernet is physical link and data link protocol
reflecting the two lowest layers of the OSI Reference Model.
 “Frame”: In interlaced video, a frame is one complete picture. A video
frame is made up of two fields, or two sets of interlaced lines. In a film,
a frame is one still picture of a series that makes up a motion picture.
VSP 112W
User Manual
18
1. Brief Introduction
Terms and Definitions
 “Gamma”: The light output of a CRT is not linear with respect to the
voltage input. The difference between what you should have and what
is actually output is known as gamma.
 “HDMI” - High – Definition Multimedia Interface: An interface used
primarily in consumer electronics for the transmission of
uncompressed high definition video, up to 8 channels of audio, and
control signals, over a single cable. HDMI is the de facto standard for
HDTV displays, Blu-ray Disc players, and other HDTV electronics.
Introduced in 2003, the HDMI specification has gone through several
revisions.
 “HDSDI”: The high-definition version of SDI specified in SMPTE-292M.
This signal standard transmits audio and video with 10 bit depth and
4:2:2 color quantization over a single coaxial cable with a data rate of
1.485 Gbit/second. Multiple video resolutions exist including
progressive 1280x720 and interlaced 1920x1080 resolutions. Up to 32
audio signals are carried in the ancillary data.
 “JPEG” (Joint photographic Expects Group): Commonly used
method of loss compression for photographic images using a discreet
cosine transfer function. The degree of compression can be adjusted,
allowing a selectable tradeoff between storage size and image quality.
JPEG typically achieves 10:1 compression with little perceptible loss
in image quality. Produces blocking artifacts.
 “MPEG”: Motion Picture Expect Group. A standard committee under
the auspices of the International Standards Organization working on
algorithm standards that allows digital compression, storage and
transmission of moving image information such as motion video,
CD-quality audio, and control data at CD-ROM bandwidth. The MPEG
algorithm provides inter-frame compression of video images and can
have an effective compression rate of 100:1 to 200:1.
 “NTSC”: The color video standard used in North America and some
other parts of the world created by the National Television Standards
Committee in the 1950s. A color signal must be compatible with
black-and-white TV sets. NTSC utilizes an interlaced video signals,
525 lines of resolution with a refresh rate of 60 fields per second (60
Hz). Each frame is comprised of two fields of 262.5 lines each, running
at an effective rate of 30 frames per second.
 “PAL”: Phase Alternate Line. A television standard in which the phase
of the color carrier is alternated from line to line. It takes four full
pictures (8 fields) for the color-to-horizontal phase relationship to
return to the reference point. This alternation helps cancel out phase
errors. For this reason, the hue control is not needed on a PAL TV set.
PAL, in many transmission forms, is widely used in Western Europe,
Australia, Africa, the Middle East, and Micronesia. PAL uses 625-line,
VSP 112W
User Manual
19
1. Brief Introduction
Terms and Definitions









50-filed (25 fps) composite color transmission system.
“Operator”: Refers to the person who uses the system.
“PIP”: Picture-in-Picture. A small picture within a larger picture created
by scaling down one of the images to make it smaller. Each picture
requires a separate video source such as a camera, VCR, or
computer. Other forms of PIP displays include Picture-by-Picture
(PBP) and Picture-with-Picture (PWP), which are commonly used with
16:9 aspect display devices. PBP and PWP image formats require a
separate scaler for each video window.
“Polarity”: The positive and negative orientation of a signal. Polarity
usually refers to the direction or a level with respect to a reference (e.g.
positive sync polarity means that sync occurs when the signal is going
in the positive direction).
“RJ-45”: Registered Jack-45. A connector similar to a telephone
connector that holds up to eight wires used for connecting Ethernet
devices.
―RS-232”: An Electronic Industries Association (EIA) serial digital
interface standard specifying the characteristics of the communication
path between two devices using either DB-9 or DB-25 connectors.
This standard is used for relatively short-range communication and
does not specify balanced control lines. RS-232 is a serial control
standard with a set number of conductors, data rate, word length, and
type of connector to be used. The standard specifies component
connection standards with regard to the computer interface. It is also
called RS-232-C, which is the third version of the RS-232 standard,
and is functionally identical to the CCITT V.24 standard.
“Saturation”: Chroma, chroma gain. The intensity of the color, or the
extent to which a given color in any image is free from white. The less
white in a color, the truer the color or the greater its saturation. On a
display device, the color control adjusts the saturation. Not to be
confused with the brightness, saturation is the amount of pigment in a
color, and not the intensity. Low saturation is like adding white to the
color. For example, a low-saturated red looks pink.
“Scaling”: A conversion of a video or computer graphic signal from a
starting resolution to a new resolution. Scaling from one resolution to
another is typically done to optimize the signal for input to an image
processor, transmission path or to improve its quality when presented
on a particular display.
“SDI”: Serial Digital Interface. The standard based on a 270 Mbps
transfer rate. This is a 10-bit, scrambled, polarity independent
interface with common scrambling for both component ITU-R 601 and
composite digital video and four channels of (embedded) digital audio.
“Seamless Switching”: A feature found on many video switchers. This
VSP 112W
User Manual
20
1. Brief Introduction
Terms and Definitions







feature causes the switcher to wait until the vertical interval to switch.
This avoids a glitch (temporary scrambling) which normally is seen
when switching between sources.
“SMPTE”: Society of Motion Picture and Television Engineers. A global
organization, based in the United States that sets standards for base
band visual communications. This includes film as well as video and
television standards.
“S-Video”: A composite video signal separated into the luma (―Y‖ is for
luma, or black and white information; brightness) and the chroma (―C‖
is an abbreviation for chroma, or color information).
“Sync”: Synchronization. In video, sync is a means of controlling the
timing of an event with respect to other events. This is accomplished
with timing pulses to insure that each step in a process occurs at the
correct time. For example, horizontal sync determines exactly when to
begin each horizontal scan line. Vertical sync determines when the
image is to be refreshed to start a new field or frame. There are many
other types of sync in video system. (Also known as ―sync signal‖ or
―sync pulse.‖)
“TCP/IP”: Transmission Control Protocol/Internet Protocol. The
communication protocol of the Internet. Computers and devices with
direct access to the Internet are provided with a copy of the TCP/IP
program to allow them to send and receive information in an
understandable form.
“USB”: Universal Serial Bus. USB was developed by seven PC and
telecom industry leaders (Compaq, DEC, IBM, Intel, Microsoft, NEC,
and Northern Telecom). The goal was easy plug-and-play expansion
outside the box, requiring no additional circuit cards. Up to 127
external computer devices may be added through a USB hub, which
may be conveniently located in a keyboard or monitor. USB devices
can be attached or detached without removing computer power. The
number of devices being designed for USB continues to grow, from
keyboards, mice, and printers to scanners, digital cameras, and ZIP
drives.
“VESA”: Video Electronics Standards Association. A nonprofit number
organization dedicated to facilitating and promoting personal computer
graphics through improved standards for the benefit of the end-user.
www.vesa.org
“VGA”: Video Graphics Array. Introduced by IBM in 1987, VGA is an
analog signal with TTL level separate horizontal and vertical sync. The
video outputs to a 15-pin HD connector and has a horizontal scan
frequency of 31.5 kHz and vertical frequency of 70 Hz (Mode 1, 2) and
60 Hz (Mode 3). The signal is non-interlaced in modes 1, 2, and 3 and
interlaced when using the 8514/A card (35.5 kHz, 86 Hz) in mode 4. It
VSP 112W
User Manual
21
1. Brief Introduction
Terms and Definitions
has a pixel by line resolution of 640×480 with a color palette of 16 bits
and 256,000 colors.
 “YCrCb”: Used to describe the color space for interlaced component
video.
 “YPbPr”: Used to describe the color space for progressive-scan
(non-interlaced) component video.
VSP 112W
User Manual
22
1. Brief Introduction
System Overview
System Overview
VSP 112W is the latest in entry level LED video processing, providing basic
inputs and versatile functionality for both mobile and fixed installation
advertising markets. Utilizing the latest in motion adaptive de-interlacing,
true color reconstruction and dynamic range adjustment technologies
enables the processor to provide high quality pixel based scaling for all
inputs including the integrated USB media interface.
It supports 2 composite (CVBS), 1 VGA, 1 DVI (compatible with HDMI1.3),
1 SD card, 4 USB inputs, and 1 audio, 2 DVI, 1 VGA outputs.
VSP 112W
User Manual
23
1. Brief Introduction
Application Questions
Application Questions
RGBlink offers solutions to demand technical problems. Any application
questions, or required further information, please contact with our
Customer Support Engineers. Refer to Appendix B for contact details.
VSP 112W
User Manual
24
2. Hardware Orientation
In This Chapter
This chapter provides detailed information about the VSP 112W hardware.
The following topics are discussed:

VSP 112W Back Panel

VSP 112W Front Panel
VSP 112W
User Manual
25
2. Hardware Orientation
VSP 112W Back Panel
VSP 112W Back Panel
The figure below illustrates the professional interface and control signals of
VSP 112W back panel.
NO
INTERFACE
NO
INTERFACE
1.2.6.7.11
10/100M Interface RJ45
17
DVI Input DVI-I
3.8
Power supply port of
18
VGA Input DSUB15 port
19
Audio Output
20
DVI Output DVI-I
Sending Card
4.9
USB control port of
Sending Card
5.10
DVI input port of
sending card
12
RS232 Interface
21
DVI+VGA DVI-I Output
13
USB input port
22
Switch
14
SD card input
23
Power IEC-3 port
15.16
CVBS Input BNC port
CONT Interface
11. 10/100M Interface RJ45
12. RS232 Interface
It is used to connect the computer.
INPUT Interface
It includes 2 CVBS (BNC port), 4 USB, 1 DVI-I(compatible with the HDMI
input), 1 VGA (DB15port), and 1 SD card Input.
13:USB Input
VSP 112W
User Manual
26
2. Hardware Orientation
VSP 112W Back Panel
USB input interface: can access the USB device or mobile hard disk with
USB storage function. Support general image and video formats. Mainly
used to store video program package (USB function can only achieve when
transcoding through PC, below USB1 in USB2).
Note
USB1 is master interface, USB2 is
spare interface, recommend the
use of a priority when USB1, not
recommend for USB1 and USB2
at the same time.
14:SD Card Input
SD card input interface, it is mainly used to store video program package or
application upgrade package.
Note
SD card and USB are mobile
storage interface,but SD card
priority is higher than USB;
SD card and USB are inserted
into the device , the system only
play SD card, when SD card is
removed ,will play USB .
15. 16:CVBS Input
CVBS input. Can receive standard video signal from players, cameras etc.
Input supports resolution 480i and 576i via BNC. Support standards
include: PAL, NTSC and SECAM.
17:DVI Input
DVI input interface: Input the video signal from computer, DVI signal
generator. Connect to the same DVI interface on VSP 112W.
(This Connection does not support hot-plugging)
Note
DVI-I is compatible with HDMI.
VSP 112W
User Manual
27
2. Hardware Orientation
VSP 112W Back Panel
18:VGA Input
VGA Interface input the video signal from HD player and Computer, etc.
compatible with YPbPr signal, input signal via the DB15 interface.
OUTPUT
1.2.6.7: 10/100M Interface RJ45
Gigabit copper port, used to connect LED screen.
3. 8:Power Supply Port of Sending Card
Power has been already supplied by video processor itself, no external
power supply needed.
4. 9:USB Control Port of Sending Card
5. 10:DVI Input
Input the DVI out originating from other video processors.
(This DVI connector does not support hot-plugging)
19:AUDIO Output
It is used to access the speakers or audio power amplifier system. Can be
connected with the DVI output interface video processor directly.
(This connector does not support hot-plugging)
20:DVI Output
Connect to the monitor or LED screen which has DVI interface
(This DVI connector does not support hot-plugging).
21:DVI +VGA DVI Output
DVI +VGA output via DVI connector connect to the monitor or LED screen
which has DVI interface.
(This DVI connector does not support hot-plugging).
VSP 112W
User Manual
28
2. Hardware Orientation
VSP 112W Back Panel
DVI +VGA, VGA output connector can be connected to monitor or projector
which has VGA interface.
Note
Via
adapter, can connect with
DVI-based or VGA-based equipment, and via
DVI to VGA adapter, can output VGA
only.
Switch and Power
22.23:Power Interface and Switch
AC 85-264V 3.8A 50/60Hz IEC-3 Power Interface.
VSP 112W
User Manual
29
2. Hardware Orientation
VSP 112W Front Panel
VSP 112W Front Panel
Insert power cord and push power to ON position. LCD module on the front
panel will show device information and go into self verification before it load
last setting and send processed image to the target monitor. For the first
setup, CV1 input is default source. With front panel keyboard, user can
operate VSP 112W through the menus on LCD panel.
亮彩系列
VSP 112W front panel as shown in figure:
AVDSP SERIES VSP 112W
INPUT:CV1
NO INPUT
OUTPUT FORMAT:
1920x1080x60
SV: 0.60
SN: 0052
VSP 112W
User Manual
30
2. Hardware Orientation
VSP 112W Front Panel
System into the Circulation Statement:
Cycle process displays the current input signal source, the current output format, the
current program version information, the current equipment serial number; the user
hold equipment serial number will get more effective service and support.
INPUT:CV1
NO INPUT
OUTPUT FORMAT:
1920x1080x60
SV: 0.60
SN: 0052
VSP 112W
User Manual
31
2. Hardware Orientation
VSP 112W Front Panel
VSP 112W front panel is as following:
LCD Panel
Used to show button menu and menus for interactive communication;
Signal Keys
CV1 input selection button, its LED light turns on, output will be switched
to this channel;
CV2 input selection button, its LED light turns on, output will be switched to this
channel;
VGA input selection button, its LED light turns on, output will be switched to
this channel;
DVI input selection button, its LED light turns on, output will be switched to this
channel;
USB input selection, its LED light turns on, output will be switched to this
channel, and the LCD panel will show the network, WIFI, USB and SD card
information.
Function Keys
Push to confirm the current choice item;
Push to select up items in LCD menu;
Push to select down items in LCD menu;
VSP 112W
User Manual
32
2. Hardware Orientation
VSP 112W Front Panel
Switch to select full size or screen size, just for single picture mode;
Push to select the output format by using the UP/ DOWN key.
Switch to use the user-defined mode 1;
Switch to use the user-defined mode 2;
Switch to use the user-defined mode 3;
Push to go to between scalezoomcropscale mode;
Advanced menu: press the MENU to enter the main menu, the submenus:
Device information, Factory Reset, Language and Alpha setting are all
included. Push the UP/DOWN to select the relevant submenu. For details,
please refer to MENU in menu orientation.
Push to save current config.
VSP 112W
User Manual
33
3. Hardware Installation
In This Chapter
This chapter provides comprehensive installation instruction for VSP 112W
hardware:
Following is the size of VSP 112W for your reference.
VSP 112W
User Manual
34
Safety Precautions
For all VSP 112W processor installation procedures, please observe the
following important safety and handling rules to avoid damage to yourself
and the equipment.
 To protect users from electric shock, ensure that the chassis connects
to earth via the ground wire provided in the AC power Cord.
 The AC Socket-outlet should be installed near the equipment and be
easily accessible.
Unpacking and Inspection
Before opening VSP 112W process shipping box, inspect it for damage. If
you find any damage, notify the shipping carrier immediately for all claims
adjustments. As you open the box, compare its contents against the
packing slip. If you find any shortages, contact your sales representative.
Once you have removed all the components from their packaging and
checked that all the listed components are present, visually inspect the
system to ensure there was no damage during shipping. If there is damage,
notify the shipping carrier immediately for all claims adjustments.
Site Preparation
The environment in which you install your VSP 112W should be clean,
properly lit, free from static, and have adequate power, ventilation, and
space for all components.
VSP 112W
User Manual
35
4. Menu Orientation
In This Chapter
This chapter describes all VSP 112W processor menus, including how
they are accessed, the functions that are available, and descriptions of
each menu tree (in block diagram format).
The following topics are discussed:
• MENU

INPUT

OUTPUT

TRANSITION

AUDIO

SPLIT

SAVE SETUP

SYSTEM

LANGUAGE

FACTORY RESET
VSP 112W
User Manual
36
4. Menu Orientation
MENU
MENU
Press the MENU to main menu, main menu as shown below. Press knob
buttons to select left or right menu item. ―*‖ before the menu means it’s in
selected state. Push the knob to enter corresponding setting or view the
menu.
VSP 112W
User Manual
37
4. Menu Orientation
MENU
VSP 112W
User Manual
38
4. Menu Orientation
MENU
MENU---INPUT
Select INPUT, press it to confirm, show level 2 menus as follows:
INPUT DETAIL: Display input signal information, including CV1, CV2,
DVI, VGA, USB.
ZOOM ADJUST: It can adjust the position and the scale, as following:
H SIZE: Width setting.
V SIZE: Height setting.
H Pos: Horizontal phase setting.
V Pos: Vertical phase setting.
RESET: If quality image distort by mistake in improper operation, it can be
initialized operation to recover factory setting.
VGA ADJUST: Mainly aimed at H POS, V POS, CLOCK, PHASE when
VGA input. It also can use the AUTO ADJUST to adjust.
ADC AUTO ADJUST:Mainly aim at the BRIGHTNESS to auto adjusting.
USB ADJUST: Mainly aimed at H POS, V POS when USB input. It also
can use the AUTO ADJUST to adjust. If quality image distort by mistake in
improper operation, it can be initialized operation to recover factory setting.
MENU ---OUTPUT
Select OUTPUT, press it to confirm, show level 2 menus as follows:
OUTPUT DETAIL: Display output signal information, including DV1, DV2,
VSP 112W
User Manual
39
4. Menu Orientation
MENU
OUT FORMAT: Mainly display the current output signal and output
resolution.
Users can choose different output formats through the UP/DOWN button,
this option includes 20 common output resolutions, shown as follow:
Note
The OUT button can also fulfill this setting.
OUTPUT ADJUST: Output adjust menu, the sub-menu as following:
DVI1, setting as following:
DVI MODE: Can select HDMI agreement or DVI; by default is DVI output,
When need HDMI signal output, choose HDMI.
DATE RANGE: DVI1 out range adjustment can choose RGB or YCBCR;
among them the RGB adjusting range is between 0-255, YCBCR adjusting
range from 16 to 235.
DE ADJUST: DE adjust, the sub-menu as following:
DE ON/OFF: Can choose to open or close, when choose open, it can be
adjusted to DE, as follows:
H SIZE: Width setting;
VSP 112W
User Manual
40
4. Menu Orientation
MENU
V SIZE: Height setting;
H Pos: Horizontal phase setting;
V Pos: Vertical phase setting;
When the signal source of the screen appear black side, can use this
function adjustment, make the image to full screen display.
RESET: If quality image distorts by mistake in improper operation, it can be
initialized operation to recover factory setting.
DVI2: Including DVI MODE, DATA RANGE, DE ADJUST, and RESET,
same with DVI1.
SCALE:Scale menu as following:
H SIZE: Width setting.
V SIZE: Height setting.
H Pos: Horizontal phase setting.
V Pos: Vertical phase setting.
RESET: If quality image distorts by mistake in improper operation, it can be
initialized operation to recover factory setting.
Note
The SCALE button can also fulfill this setting.
SCREEN:Screen setting, user can change the screen through the digital
setting parameters to easily change the screen size and position. Mainly
used in the LED large screen users. Settings as follow:
H SIZE: Width setting;
V SIZE: Height setting;
H Pos: Horizontal phase setting;
V Pos: Vertical phase setting;
Mode: window mode, can scale the(Screen)and(Full)switch.
Note
The FS button can also fulfill this setting.
VSP 112W
User Manual
41
4. Menu Orientation
MENU
RESET: If quality image distorts by mistake in improper operation, it can be
initialized operation to recover factory setting.
RATIO: Proportional setting, press it, can realize the conversion between
high and wide.
Normal: Original video proportion, 4:3 aspect ratios; 16:9 aspect ratios;
PICTURE: Picture setting, the sub-menu as following:
BRIGHTNESS: It can change the image color BRIGHTNESS via
BRIGHTNESS Settings.
CONTRAST: It can change the image color CONTRAST via CONTRAST
settings.
SATURATION: It can change the image color SATURATION via
SATURATION Settings.
SHARPNESS: It can change the image color SHARPNESS via
SHARPNESS Settings.
COLOR RED: It can change the image color Red via Red Settings.
COLOR GREEN: It can change the image color Green via Green Settings.
COLOR BLUE: It can change the image color Blue via Blue Settings.
RESET: If quality image distorts by mistake in improper operation, it can be
initialized operation to recover factory setting.
Users can set according to their actual situation, this function mainly
suitable for these very professional for image quality. Non-professionals
are not suggesting above operations. If quality image distorted by mistake
in improper operation, it can be initialized operation to recover factory
setting.
The numerical range that needs adjusting is between 0-100. Press MENU
to exit and return to higher level MENU.
PIP: PIP setting, press PIP and choose ON to set PIP mode.
LAYOUT: Can choose PIP layout, the corresponding results are as follows:
VSP 112W
User Manual
42
4. Menu Orientation
MENU
PIP L+T
PBP L+R
PBP T+B
SWAP IMAGE: It can set PIP to swap exchange, when choose ON, it can
realize the main and sub-picture exchange.
ALPHA: Can set the image display transparency, regulating range between
0 - 16.
SELECT: Can choose to set the size or position of IMAGE A or IMAGE B
individually.
TEXT OVERLAY: Text overlay function, settings as follows:
TEXT OVERLAY: Can select ―ON‖ or ―OFF‖, OFF is the default state.
PRESET: Can preset value of the following functions, and total 13 modes:
User: User mode.
WhOnBk1: White On Black 1.
WhOnBk2: White On Black 2.
BkOnWh1: Black On White 1.
BkOnWh2: Black On White 2.
GrnOnBk1: Green On Black 1.
GrnOnBk2: Green On Black 2.
GrnOnWh1: Green On White 1.
GrnOnWh2: Green On White 2.
RedOnBk1: Red On Black 1.
RedOnBk2: Red On Black 2.
RedOnWh1: Red On White 1.
RedOnWh2: Red On White 2.
VSP 112W
User Manual
43
4. Menu Orientation
MENU
BLEND MODE: Blend mode, with two modes, ―Mode 1‖ and ― Mode 2‖.
Mode 1: Graphic content locate at the top and is non-transparent,
background transparency is controlled by double-picture transparency;
Mode 2: Graphic content is controlled by double-picture transparency, the
background is completely transparent;
BLEND LEVEL: Can set the image display transparency, regulating range
between 0 - 16.
ABOVE/BELOW:
ABOVE: In image 2, if the pixel value is higher than the setting value, then
the image is the graphic content pixel, otherwise, it is the graphic
background pixel. It should combined with "AND/OR" conditions when
judging.
BELOW: In image 2, if the pixel value is lower than the setting value, then
the image is the graphic content pixel, otherwise, it is the graphic
background pixel. It should combined with "AND/OR" conditions when
judging.
AND/OR:
AND: All ―Red, Green, Blue‖ value must meet ABOVE or BELOW
conditions.
OR: Any one of ―Red, Green, Blue‖ value should meet ABOVE or BELOW
conditions.
RED: Red limit, cut-off point condition of ABOVE and BELOW condition in
red channel, the range is 0 ~ 255.
GREEN: Green limit, cut-off point condition of ABOVE and BELOW
condition in green channel, the range is 0 ~ 255.
BLUE: Blue limit, cut-off point condition of ABOVE and BELOW condition in
blue channel, the range is 0 ~ 255.
DISPLAY MODE:
MODE: Image mode selection, user can choose different output modes
VSP 112W
User Manual
44
4. Menu Orientation
MENU
according to their requirement, such as: black, video image, freeze image,
pure color image, test pattern.
TEST PATTERN: Test pattern setting, press UP/DOWN button, there are
1-66 kinds of modes for choose.
FLAT COLOR: When the output mode is pure color image, choose
corresponding red, green and blue color value in this option to meet the
practical needs.
GAMMA: Gamma setting, press it to adjust the image gamma value;
Gamma values include: -1.2, -1.4, -1.6, 1, 1.2, 1.4, 1.6, sRGB;
MENU --- TRANSITION
Choose the TRANSITION, press SEL to confirm, then the LCD screen
displays the level 2 menu as following:
MODE: Switch mode, including the following modes:
CUT: Seamless switching.
FADE: Fade in fade out.
POP L+T: Upper left corner pop up
PUSH L+T: Upper left corner push
POP R+T: Upper right corner pop up
PUSH R+T: Upper right corner push
POP L+B: Lower left corner pop up
PUSH L+B: Lower left corner push
POP R+B: Lower right corner pop up
VSP 112W
User Manual
45
4. Menu Orientation
MENU
PUSH R+B: Lower right corner push
POP CENTRE: Centre pop up
PUSH CENTRE: Centre push
POP LEFT: Left pop up
PUSH LEFT: Left push
POP RIGHT: Right pop up
PUSH RIGHT: Right push
POP TOP: Top pop up
PUSH TOP: Top push
POP BOTTOM: Bottom pop up
PUSH BOTTOM: Bottom push
Note:
On behalf of the image emerging;
On behalf of the image disappearing;
Arrows represents the direction of the image move, that is, the image that
arrow point, is compressed or stretched to the direction that arrow indicates,
until disappear or full screen.
VSP 112W
User Manual
46
4. Menu Orientation
MENU
FADE TIME: Switch time setting. Press UP/DOWN button to choose the
time and press SEL to confirm. The switching time ranges from 0 to1.0.
ALPHA: It can set the image transparency, regulating range between 0 16.
DEINTERLACE: Force Deinterlace function, can choose ―ON‖ or ―OFF‖.
ON: Force interlace, no effect switching.
OFF: No deinterlace, with effect switching.
MENU --- AUDIO
MUTE: Mute, can open or close it.
VOLUME: Volume adjustment.
AUDIO IN: Can choose audio input source for IMAGE A main image or
IMAGE B sub-image.
HDMI: Can choose HMDI audio as INTERNAL embedded audio or
EXTERNAL audio.
MENU --- SPLIT
Choose the SPLIT, press SEL to confirm, then the LCD screen displays the
level 2 menu as following:
SPLIT ON/OFF: Split function, can choose ―ON‖ or ―OFF‖.
H TOTAL: Horizontal total.
V TOTAL: Vertical total.
H SIZE: Width setting.
V SIZE: Height setting.
H POS: Horizontal phase setting.
V POS: Vertical phase setting.
MENU --- SAVE SETUP
SAVE TO: The device provides ten save modes, users can save the
current operation to SAVE1, SAVE2, SAVE3;
Note
The SAVE button can also fulfill this setting.
VSP 112W
User Manual
47
4. Menu Orientation
MENU
LOAD FROM: It can call the saved user modes via the call save function.
DELAY CALL: Set delay the output time. When more than one equipment
power on, and the processor is the end equipment in order to improve
question that can’t identify the input signal and phenomenon that LED
screen appear messy code and flash screen, now need to delay the input
time.
MENU --- SYSTEM
SYSTEM INFO: System information.
MCU VER: Information of MCU version.
VIDEO VER: Information of VIDEO version.
SN: It is the Factory serial number of VSP 112W which is used to search
the information of VSP 112W.
SV: Information of software version.
MAC: MAC address.
TECH SUPPORT:
SALES HOTLINE.
AFTER-SALE SERVICE.
TEL: Phone of technology support.
WEB SITE: Company web site of technology support.
EMAIL: Email of technology support.
ETHERNET: Network setting, including:
IP ADDRESS: 192.168.000.100.
LOCK FRONT PANEL: Through this setting can choose whether to lock
the keys, if the key is locked, the equipment will remind: "please click
MUNE and SEL key to release button!" User can also press the two keys to
unlock equipment.
MENU --- LANGUAGE
Through this option, user can choose Chinese or English according to their
needs to operate the interface more quickly.
VSP 112W
User Manual
48
4. Menu Orientation
MENU
MENU --- FACTORY RESET
Enter FACTORY RESET or IP reset; choose YES and press the SEL button
to confirm; then VSP 112W is reset to its factory settings. After 5 seconds, it
completes factory settings and is ready for more operations.
VSP 112W
User Manual
49
5. Communication Software Guideline
In This Chapter
This chapter provides detailed information about the control communication
software. The following topics are discussed:

Software Installation

Software Operation

How to Connect PC Through LAN Interface
VSP 112W
User Manual
50
5. Communication Software Guideline
Software Installation
Software Installation
AVDSP video processor is very easy to be configured with user friendly
communication software, support drag and drop operation for edit and
display. Also it can be customized with schedule function.
Double click
to install, English version default for use, click ―select‖
to next dialog:
And in next dialog is the user agreement of the software, click Agree to go
on:
VSP 112W
User Manual
51
5. Communication Software Guideline
Software Installation
User can select ―Change‖ to choose the VSP 112W install software:
VSP 112W
User Manual
52
5. Communication Software Guideline
Software Installation
Click ―Next‖ to go on:
Click ―Next‖ to go on:
VSP 112W
User Manual
53
5. Communication Software Guideline
Software Installation
Click ―Next‖ to go on:
Click ―Finish‖ and ready to run VSP 112W console:
VSP 112W
User Manual
54
5. Communication Software Guideline
Software Operation
Software Operation
Install communication which comes with the package of VSP 112W device.
Double click
icon from home screen to run the software.
Double click
icon, then choose and click
to run the
software.
VSP 112W communication software interface as shown:
Connection
When control video processor through PC software, besides the power
cord, the product default equip with a line that is COM (RS-232), 9-pin
(DB9F), RJ11 COM crystal head (6 B4C). Below are the details about
connection of steps:
First connect 9-pin (DB9F) to the computer on the corresponding port, and
connect COM crystal to RS232 port on video processor. Open video
processor; Next, operate the computer, back to computer desktop, right
click [My computer] to [Properties], find the [Hardware] option card, as
follows, left click [Device manager]:
VSP 112W
User Manual
55
5. Communication Software Guideline
Software Operation
Find [COM and LPT] port in [device manager], click the plus sign on the left,
record serial interface name that computer provides, as following chart, the
serial port is COM1.
Confirm used COM and open control software, click [communication]
page, enter setup option, Serial is the default COM, click icon
to
refresh COM number,choose available COM,default Baud rate is115200.
After serial setting, click
VSP 112W
icon, the icon becomes
User Manual
when
56
5. Communication Software Guideline
Software Operation
successfully connected,on the left button showing
,
meaning has connected video processor through COM, and can control
video processor through the PC software.
Note
It is unavailable for VSP 112W V1.5 currently.
Ethernet ,user can fill any number less than 1023 in local port,the remote
port must be 192.168.0.100 and the remote port must be 1000. After
setting above, click the icon
to connect with the net work. If
successful connect, the icon becomes
showing
VSP 112W
,status on the left button
。
User Manual
57
5. Communication Software Guideline
Software Operation
Use
File Toolbar
:Open script. User can open saved script and alter its parameters.
: Save script. Save current user parameters as script to the
prescribed path.
:Import template. There are six templates for user. Users can setup
one of templates as the common one.
VSP 112W
User Manual
58
5. Communication Software Guideline
Software Operation
:Export template. Export current config as template.
:Option: User can choose open device when start and using script
saved before or execute schedule edited before when start.
If user choose open device when start, user can use last run, use script file
or none when user start. User can click
to choose which script user
want to open.
If user choose execute schedule when start, the next dialogue will display
when software run.
VSP 112W
User Manual
59
5. Communication Software Guideline
Software Operation
Note
It is unavailable for VSP 112W V1.5 currently.
:Language: The software supports Chinese, English and German
version.
The picture following is the German dialogue.
:Exit
Communication Toolbar
:Open COM.
:Close COM
:Set COM.
VSP 112W
User Manual
60
5. Communication Software Guideline
Software Operation
Device Toolbar
:Synchronization.
:Save to flash.
Note
Same as MENU
SAVE SETUP
SAVE
TO or the same as the SAVE key.
:Load form Flash.
Note
Same as MENU
SAVE SETUP
LOAD FROM.
:Factory setup;
:Advance
VSP 112W
User Manual
61
5. Communication Software Guideline
Software Operation
Note
Advance is only done by engineer. Please
connect us for password.
Schedule Toolbar
:Customize schedule
:Execute schedule. Execute tasks according to schedule.
VSP 112W
User Manual
62
5. Communication Software Guideline
Software Operation
Help Toolbar
:Help: Display helps dialogue;
:About: Display information of software;
Output Resolution Toolbar
User can choose different output resolution by selecting from pull down list.
VSP 112W has 20 output resolutions for users selection.
Note
Same as MENU
OUTPUT
FORMAT OUT
or OUT key.
Images Display Mode Toolbar
Choose to work in single channel or dual channel.
Layout Toolbar
If in single channel mode, the dialog is in grey and it is in limited use.
If in dual channel mode, user can set the device to work in PIP or PBP
mode directly with quick preset layout button as following.
VSP 112W
User Manual
63
5. Communication Software Guideline
Software Operation
Note
Same as MENU
OUTPUT
PIP
LAYOUT.
Aspect Ratio Toolbar
Users can select 4:3 or 16:9 in the pull-down options.
Note
Same as MENU
OUTPUT
RATIO
Signal Input Toolbar
The white area displays the name of input interface when the mouse is
over the interface picture on the left. The green pane means current
selected interface.
When user selects a dual channel mode, select any channel image, click
on the toolbar interface the ICONS for the channel selection input interface,
i.e.: Composite1, Composite2, DVI, VGA, green toolbar says it has chosen
the current interface for channel 1 input interface, the default last single
channel chosen interface for channel 2 input interface, the currently
selected channel will be shown on the right side of the source.
VSP 112W
User Manual
64
5. Communication Software Guideline
Software Operation
Screen Parameter Toolbar
User can set size and position of the screen simply, mainly applies to LED
screens users. After setting screen parameter, the user choice PIP or PBP
operation, display picture can directly shows on corresponding screen.
Note
Same as MENU
OUTPUT
SCREEN
Image Toolbar
User can scale the images;Image 2 can’t choose in single channel mode.
Note
Same as MENU
OUTPUT
SCALE , or
SCALE key.
Display Toolbar
When it is in Live Video, the video plays properly; when it is in Freeze
Frame, the video stop playing.
Note
Same as MENU
MODE
VSP 112W
OUTPUT
DISPLAY
MODE.
User Manual
65
5. Communication Software Guideline
Software Operation
Setting Gamma is generally not recommended, since LED large screen
itself has Gamma function. For further information, users can contact with
our customer service team.
Note
Same as MENU
OUTPUT
GAMMA
Output Image Setup Toolbar
User can customize the brightness and the contrast.
Note
Same as MENU
OUTPUT
PICTURE.
Images Display Toolbar
User can customize image or images position and size just by drag and
drop image (images) in this area. This process is sync to the parameters in
images toolbars.
VSP 112W
User Manual
66
5. Communication Software Guideline
Software Operation
User Mode Toolbar
Users can recall the saved user mode1, mode2 or mode3
Log Toolbar
User can save or delete the operate log file.
Information Toolbar
It is the VSP 112W software version, core board version, firmware version
and the serial number in bottom of the software interface.
[Video Processor] Options
VSP 112W
User Manual
67
5. Communication Software Guideline
Software Operation
IP SETUP: shown as follows:
Specific operation is as follows:
Network Setting:
1. Choose ―Network Setting‖
2. Choose the network mode, if
choose ―Static IP‖, input the
network parameters. If choose
―DHCP‖, then the DHCP server will
assign IP address automatically.
Broadcast port is default 3999, do
not change it.
3.
After
setting,
click
―Set
Network
Address‖, then Red Player will restart,
make other settings after restart.
VSP 112W
User Manual
68
5. Communication Software Guideline
Software Operation
WIFI Setting:
2. Input WIFI
1. Choose ―WIFI Setting‖
parameters.
3. Click ―Set Network Address‖, then Red Player will
restart, make other settings after restart.
Internet Setting:
4. Choose ―Network Setting‖ and ―DHCP‖, and click ―Set Network Address‖
2. Input Internet
parameters.
1. Choose ―Internet Setting‖
Note:
Grouptest
changed freely.
3. Click ―Update‖
After setting, user can read setting, restart terminal, and set name.
Red Player Editor: Can edit the program, click it and shows as follows, for
details, please refer to: How to edit the Program.
VSP 112W
User Manual
69
can
be
5. Communication Software Guideline
Software Operation
Split:
Split function, choose ―ON‖ can set H total, V total, H position, V position, H
size and V size.
Note
Same as MENU
SPLIT.
Device Schedule:
Users can set up VSP 112W to play the appointed input video automatically
in time and operation of single or dual channels, ratio place.
Users can setup up to 10 timing operation in the schedule.
VSP 112W
User Manual
70
5. Communication Software Guideline
Software Operation
Note
It is unavailable for VSP 112W V1.5 currently.
IP Address:
Users can set equipment IP, usually used under the condition of one
computer control or remote control several computers. It takes effect
immediately after users change IP through serial port; and when users
change IP through network, it takes effect after reopen the software.
Note
It is unavailable for VSP 112W V1.5 currently.
Clock:
Users can set or adjust lower computer time through‖ clock‖
VSP 112W
User Manual
71
5. Communication Software Guideline
Software Operation
Audio setting:
[Help] Options
Version: The update of software
About: The information of the software version and the company.
VSP 112W
User Manual
72
5. Communication Software Guideline
How to Connect PC Through LAN Interface?
How to Connect PC Through LAN Interface
First, install the upper computer software in the computer;
Connect VSP 112W and computer with cable, the connection diagram is
as follows:
Power on VSP 112W, start the network function, specific steps are as
follows:
The fist step: push MENU button ,get into MENU—SYSTEM—ETHERNET,
check the IP address of the equipment, the equipment factory default IP
address : 192.168.0.100.
The second step: check computer IP address, Mouse click start, choose
Run
,run <cmd> instruct
,
Click <OK>,run <ipconfig>
,
<Enter> button,the IP address of the red circle display for the computer:
192.168.0.15 ;
VSP 112W
User Manual
73
5. Communication Software Guideline
How to Connect PC Through LAN Interface?
The third step:Equipment IP address :192.168.0.100;
Computer IP address :192.168.0.15;
The four step :two IP address in the same band,192.168.0.XXX,the fourth
section number is not the same,can communication connection line CAT5.
Note
If the computer IP address and equipment
address are different,two IP address not in the
same band,for example,the computer IP
address is 218.032.010.201 ; Equipment IP
address :192.168.0.100;
Solution 1:change the IP address of the video
processor for :218.032.010.xxx。
Change the IP address ,push <MENU>
button
,enter
into
<MENU>--<SYSTEM>--<TTHERNET>--<IP
ADDRESS>,you can change IP address ,
change the IP address of the video processor
and computer’s IP address in the same band,
218.032.010.xxx,more detailed please refer to
the operation of <MENU---SYSTEM>,Restart
the processor.
Solution 2:change the computer IP address for
192.168.0.xxx;
Open network connections,right click on
properties,
VSP 112W
User Manual
74
5. Communication Software Guideline
How to Connect PC Through LAN Interface?
,choose Internet protocol(TCP/IP),
Click properties,
you can change IP address,change the IP
address of the video processor and computer’s
IP address in the same band,192.168.0.XXX;
VSP 112W
User Manual
75
5. Communication Software Guideline
How to Connect PC Through LAN Interface?
The fiver step :Open the upper computer software, click
,
interface is shown as Choose [Ethernet];
Input IP address, click [OK].
Click
to open the serial port, check the if the [Comm] icon in the
lower-right corner of the control software interface is green, and log outputs
information smoothly, then it can control the device through PC software.
VSP 112W
User Manual
76
6. System Setup and Operations
In This Chapter
This chapter provides comprehensive instructions for system setup and
operations. The following topics are discussed:

Interface and Input Signal Option

How to Confirm the Device is in Normal Operation

How to choose the language on the LCD

How to Adjust the Output Resolution

How to Realize Single Image Switching

How to Set up the Size and Position of Signal Image

How to Realize Screen Size and Full Size Switching

How to Edit the Program

How to Set Router VPN

How to Save the Parameter

How to Load the Saved Parameter

Usage of SD Card and USB
VSP 112W
User Manual
77
6. System Setup and Operation
Interface and Input Signal Option
Interface and Input Signal Option
NO
INTERFACE
NO
INTERFACE
1.2.6.7.11
10/100M Interface RJ45
17
DVI Input DVI-I
3.8
Power supply port of
18
VGA Input DSUB15 port
19
Audio Output
20
DVI Output DVI-I
Sending Card
4.9
USB control port of
Sending Card
5.10
DVI input port of
sending card
12
RS232 Interface
21
DVI+VGA DVI-I Output
13
USB input port
22
Switch
14
SD card input
23
Power IEC-3 port
15.16
CVBS Input BNC port
20. DVI1 have default the main image output , use for connecting the
sending card of led screen. VSP 112W support resolution format as
following:
800x600x60Hz, 1024x768x60Hz, 1024x768x75Hz, 1280x720x60Hz,
1280x720x50Hz, 1280x768x60Hz, 1280x800x60Hz, 1280x1024x60Hz,
1360x768x60Hz, 1366x768x60Hz, 1400x1050x60Hz, 1440x900x60Hz,
1600x1200x60Hz,1680x1050x60Hz,1920x1080x60Hz,1920x1080x50Hz,
1920x1200x60Hz, 2048x1152x60Hz, 2560x812x60Hz, 2560x816x60Hz.
VSP 112W
User Manual
78
6. System Setup and Operation
Interface and Input Signal Option
Note
Same as MENU
OUTPUT
OUTPUT
FORMAT or OUT key.
21. DVI2 + VGA output interface default for preview, mainly through the
display preview will output signal, the output signal for DVI video signal and
VGA video signal, may meet with DVI interface or VGA interface display
and display equipment signal images look prison. Through the DVI - I
interface output signal (Preview adopt standard DVI - I interface,
compatible VGA output, through the terminal adapter VGA output; The
resolution of the output support for:
800x600x60Hz,1024x768x60Hz,1024x768x75Hz,1280x720x60Hz,
1280x720x50Hz, 1280x768x60Hz, 1280x800x60Hz, 1280x1024x60Hz,
1360x768x60Hz, 1366x768x60Hz, 1400x1050x60Hz, 1440x900x60Hz,
1600x1200x60Hz,1680x1050x60Hz,1920x1080x60Hz,1920x1080x50Hz,
1920x1200x60Hz, 2048x1152x60Hz, 2560x812x60Hz, 2560x816x60Hz.
In addition to CONT part and send card and power interface outside, other
interface for video signal input interface,
CVBS( BNC Port) Can receive standard video signal from players,
cameras etc. Input supported resolution 480i and 576i via BNC. Supported
standards include: PAL, NTSC and SECAM.
USB(USB Port)Can access the USB device or mobile hard disk with USB
storage function. Mainly used to store video program package.
DVI(DVI-I Port)Computer graphics interface may receive the DVI output
interface can also through the DVI turn HDMI cable to connect the
computer graphics HDMI output or DVD HDMI output;
VGA(DB15 Port)Can support HD player, computer, video signal. Through
the DB15 interface input signal.
VSP 112W
User Manual
79
6. System Setup and Operation
Interface and Input Signal Option
22. Power:Power has been already supplied for video processor
23. AEC Port:AC 85-264V 3.8A 50/60Hz IEC-3 Power Interface.
VSP 112W
User Manual
80
6. System Setup and Operation
How to Confirm the Device is in Normal Operation
How to Confirm the Device is in Normal Operation
1. Firstly , make sure the power of device setup
2. After power on , the fans running , the button scanning
3. After the button scanned, the device operate, the LCD display that:
亮彩系列
AVDSP SERIES VSP 112W
INPUT:CV1
NO INPUT
OUTPUT FORMAT:
1920x1080x60
SV: 0.60
SN: 0052
VSP 112W
User Manual
81
6. System Setup and Operation
How to Confirm the Device is in Normal Operation
4. After the start, the completion of equipment factory default call
parameter or save1 system parameters, CV1 key light is lit up; System into
the circulation state: circulation process indicates that the current input
signal source, the current output format, the current program version
information, the current equipment serial number, the user hold equipment
serial number will get more effective service and support.
INPUT:CV1
NO INPUT
SV: 0.60
SN: 0052
OUTPUT FORMAT:
1920x1080x60
5. System into the circulation state of equipment for the normal starting.
VSP 112W
User Manual
82
6. System Setup and Operation
How to Choose the Language on the LCD
How to Choose the Language on the LCD
1. Press MENU button, enter menu option, press UP/DOWN button, and
choose [LANGUAGE 语言] option.
SYSTEM
>>
>LANGUAGE 语言 ENG
2. Press SEL button,change the status of option―>‖to―*‖:
SYSTEM
>>
*LANGUAGE 语言 ENG
3. Press UP/DOWN button again, change the default ―ENGLISH‖ to
―Chinese‖.
SYSTEM
>>
*LANGUAGE 语言 中文
4. After finishing, press SEL button to confirm, the LCD display
―ENGLISH‖ has been changes to ―Chinese‖.
SYSTEM
>>
>语言 LANGUAGE 中文
VSP 112W
User Manual
83
6. System Setup and Operation
How to Adjust the Output Resolution
How to Adjust the Output Resolution
1. Press OUT button, enter output format option:
OUTPUT FORMAT:
>1920x1080x60
2. Press UP/DOWN button, choose the required resolution. for example:
2048x1152x60;
OUTPUT FORMAT:
*2048x1152x60
3. Press SEL button, finish the choice of resolution.
OUTPUT FORMAT:
>2048x1152x60
Note
Same as MENU
OUTPUT
OUTPUT
FORMAT
VSP 112W
User Manual
84
6. System Setup and Operation
How to Realize Single Image Switching
How to Realize Single Image Switching
Boot the system default CV1 to the current input source (key light and
scintillation), if need seamless switching other source such as DVI, direct
light touch DVI key, LCD screen display as follows
SOURCE SELECT:
>DVI
Choose DVI buttons, CV1 key light is off, and DVI key lights and shining,
can realize single picture of input signal source switching (input signal
source by original CV1 switching to DVI).The same method can be
switched CV2, VGA, USB.
Note
Seamless switch: means signal switch will not
appear any flash point, black, shaking or delay
VSP 112W
User Manual
85
6. System Setup and Operation
How to Set Up the Size and Position of the Single Image
How to Set Up the Size and Position of the Single Image
1. Press MENU button, enter the menu option. Press UP/DOWN button,
choose the [OUTPUT] option.
INPUT
>OUTPUT
>>
>>
2. Press SEL button to confirm, then press UP/DOWN button, choose
[SCALE] option.
OUTPUT ADJUST >>
>SCALE
>>
3. Press SEL button, and set the required value, press SEL button to
confirm.
>H SIZE
V SIZE
>H POS
V POS
1920
1200
0000
0000
4. After finish, press MENU to return to top level menu.
Note
The [SCALE] button can also fulfill this setting.
VSP 112W
User Manual
86
6. System Setup and Operation
How to Realize the Screen Size and Full Size Switching
How to Realize the Screen Size and Full Size Switching
1. Press MENU button, through UP/DOWN button, choose [OUTPUT],
and choose [SCREEN] option:
>INPUT
OUTPUT
>SCREEN
RATIO
>>
>>
>>
NORMAL
2. Press SEL to confirm, according to user needs, can be shown on the
screen size and position are Settings:
>H SIZE
V SIZE
>H POS
V POS
1920
1080
0
0
3. When setup is completed, choose the option SCREEN SIZE or FULL
SIZE in [MODE] option in the [SCREEN], it can realize the screen size
and full size switching.
Note
The [FS] button can also fulfill this setting.
VSP 112W
User Manual
87
6. System Setup and Operation
How to Edit the Program
How to Edit the Program
Open the VSP 112W PC software, choose ―Red Player Editor‖ option in
[VProcessor], shown as follows:
Red Player Editor interface is as follows:
VSP 112W
User Manual
88
6. System Setup and Operation
How to Edit the Program
1. Import and export program, user can export the edited program.
2. Add program
Global page: play window is above
Page1, and playing time is not
bound by task list.
Page1: play window is below global
page window, and playing time is
limited by task list.
VSP 112W
User Manual
89
6. System Setup and Operation
How to Edit the Program
3.1 Display clock
2. Add Window
1. Select Global Page
3.2 Add clock in play window
2. Add clock
1. Select Window1
VSP 112W
User Manual
90
6. System Setup and Operation
How to Edit the Program
3.3 Modify clock attribute
2. Modify clock attribute
1. Select Clock1
4.1 Video play
2. Add Window
1. Select Page1
VSP 112W
User Manual
91
6. System Setup and Operation
How to Edit the Program
4.2 Add video file in media library
2. Click ―Add‖ button
1. Select Video
4.3 Set video file conversion parameters
VSP 112W
User Manual
92
6. System Setup and Operation
How to Edit the Program
4.4 Drag the video in media library to play window
2. Drag to the target
play window, then
release the mouse
1. Select video files,
press mouse left key.
4.5 Video voice switch
1. Select video files
2. Voice switch setting
VSP 112W
User Manual
93
6. System Setup and Operation
How to Edit the Program
5.1 Broadcast Text
2. Add play text for selected
play window (Here take
single text for example)
1. Add play window
5.2 Edit broadcast text in pop-up edit box
VSP 112W
User Manual
94
6. System Setup and Operation
How to Edit the Program
5.3 Adjust the position of text play window, can adjust by dragging the mouse or properties
window on the right side.
6.1 Image play, Import images to media library.
2. Click ―Add‖ button
2. Select Image
VSP 112W
User Manual
95
6. System Setup and Operation
How to Edit the Program
6.2 Add image files in media library to play window
2. Drag the images in
media library to the
target play window.
1. Select image files in
media library, and press
mouse left key.
6.3 Add program background picture
1. Select program
2. Click to set
background
picture
片
3. Select picture in pop-up
media library, and click OK
VSP 112W
User Manual
96
6. System Setup and Operation
How to Edit the Program
7.1 Display sensor information
2. Select add
Senor
1. Select the window that
display sensor information.
7.2 Edit sensor information display format
1.
Edit
senor
information display
format
8. Adjust play window layer, as follows: play window of Global Page is above Page1 play
window, that is Global Page covers Page1. Layer relationships in Page1 play window are:
more from the back play window rows the layer appears higher, as shown below,
Window4 covers Window2.
VSP 112W
User Manual
97
6. System Setup and Operation
How to Edit the Program
Adjust the selected window layer
by clicking up or down arrow
Layer 3
Layer 4
Layer 1
Layer 2
9.1 Edit program task list
1. Select Program1
2. Click to edit task list
9.2 Edit task list
Play mode: 1. Normal means continuously play from beginning to the end, if set invalid
week, it will not play in invalid week; 2. Interval means play from the starting time to end
time between the start date and end date. If the starting time is greater than the end time,
it will span the midnight to the end time of the second day. For example, if set starting time
for 2012/1/1 12:00:00, and the end time is 2012/1/5 8:00:00, then program will play from
2012/1/1 12: 00:00 to 2012/1/2 8:00:00, because it is before its play time, it will play again
on 2012/1/2 12:00:00.
VSP 112W
User Manual
98
6. System Setup and Operation
How to Edit the Program
1. Add task
2. Edit task
10.1 Publish the edited program
10.2 Add Terminal Device
Known IP: manually input IP address and add terminal;
IP automatic retrievals: When PC and asynchronous control card access the same LAN,
and both are dynamic access IP, click "search" in publish window to search device, then
the device will be automatically added to the terminal list.
VSP 112W
User Manual
99
6. System Setup and Operation
How to Edit the Program
2.
Modify
device
connection parameters
1. Add Device
3. Add
10.3 Publish program
4. Publish
1. Type select program,
Content
2.
Tick
the
select
edited
3.
Select
the
target device
program to publish
terminal
VSP 112W
User Manual
100
6. System Setup and Operation
How to Edit the Program
10.4 Upload auto brightness control. Set brightness list, then publish as upload program.
3. Upload brightness list
1.Type select Bright_ctrl,
click Auto_brightness
2. Edit brightness list, then click OK
10.5 Asynchronous control card publish introduction. As shown below, the main publish
types include:
1. Program: Program list, can be uploaded to the terminal program;
2. Bright_ctrl:Automatic brightness control, Led display brightness will
change according to the list ambient brightness;
3. Upgrade: Upgrade asynchronous control card;
4. Update play;
5. Restart: Restart asynchronous control card;
6. Update time: Update asynchronous control card time (Set to PC current
time)
VSP 112W
User Manual
101
6. System Setup and Operation
How to Edit the Program
10.6 FTP server publish introduction. As shown below, the main publish types include:
1. Program: The program that get from asynchronous control card timing to the
server.
2. Clear Files: Remote clear the asynchronous control card media files;
3. Upgrade: Remote upgrade the asynchronous control card;
4. Restart: Remote restart the asynchronous control card;
VSP 112W
User Manual
102
6. System Setup and Operation
How to Edit the Program
11.1 Publish program to FTP Server. First, add Ftp server, as follows:
3.
Modify
device
connection parameters
1. Select FTP
Server
2. Add device
4. Add
11.2 Upload program to FTP Server
4. Publish
3. Select target
1.Type select program,
Content
select
device
edited
program to upload
2.
Tick
FTP
Server
VSP 112W
User Manual
103
6. System Setup and Operation
How to Edit the Program
12. Publish program to local U disk
3. Publish
1.Type select program,
Content select edited
2. Tick Local U disk
program to upload
12.1 Asynchronous control card upgrade, open the window as follows:
4. Publish
1. Type choose Upgrade
2. Click and open upgrade file
3. Tick update Terminal
VSP 112W
User Manual
104
6. System Setup and Operation
How to Set Router VPN
How to Set Router VPN
Here we take VOLANS router VE760w for example, and it is similar to other routers with
VPN function.
VPN Server Set Up
1. VOLANS router default gateway is192.168.0.1, default account is admin, and default
password is admin.
2. Set local connection to automatically obtain IP and connect to the router.
3. After connect successfully, get IP 192.168.0.174.
4. Enter the router IP 192.168.0.1 in browser address bar, then input account admin and
password admin in the login window, be sure enter the router setting page.
VSP 112W
User Manual
105
6. System Setup and Operation
How to Set Router VPN
5. This step depends on the environment set up by router, including:
Environment A router connect to the broadband line
Environment B router set up in the local area network (LAN), and access to the wide area
network (WAN).
(1) For environment A, it should enter the router's broadband connection setting.
Click the basic setup on the left side - WAN configuration
VSP 112W
User Manual
106
6. System Setup and Operation
How to Set Router VPN
Click WAN1 edit
.
Fill in the broadband account and password or static IP address and save, confirm if
connected to the WAN.
VSP 112W
User Manual
107
6. System Setup and Operation
How to Set Router VPN
(2) If is environment B, ignore environment A setting.
Then VE760w used as child router for switching. The router IP cannot conflict with the
IP already set up in the LAN. Need to change the router IP.
Click the basic setup on the left side - LAN configuration, modify 192.168.0.X and
save, then reboot the router.
VSP 112W
User Manual
108
6. System Setup and Operation
How to Set Router VPN
6. Click "virtual private network" on the left side menu--‖PPTP server‖
Tick and enable PPTP,
The PPTP client address range should be assigned to the IP address that VPN client
dialed, should avoid conflict with other PC user's IP address.
The setting address is
7. Click ―PPTP users‖ after save.
VSP 112W
User Manual
109
6. System Setup and Operation
How to Set Router VPN
8. Click
, fill in the user name and password (the account and password that
necessary for VPN dial-up), and then save.
VSP 112W
User Manual
110
6. System Setup and Operation
How to Save the Parameter
How to Save the Parameter
Save user mode to the customer for different scene directly call; leave out
the edit operation inconvenience, VSP 112W provides ten save
preferences.
1. Press SAVE button, the key lights, the SAVE function open.
2. SAVE1, SAVE2, SAVE3 all light;
3. Select the location of the need to save, light touch the corresponding key,
such as save to SAVE2, light touch SAVE2 key can complete parameter
preservation.
SAVE TO:
> SAVE1
SAVE TO:
>SAVE2 FINISHED!
Note
Same as MENU
VSP 112W
User Manual
SAVE SETUP
SAVE TO
111
6. System Setup and Operation
How to Load the Saved Parameter
How to Load the Saved Parameter
Save user mode to the customer for different scene directly call; leave out
the edit operation inconvenience, VSP 112W provides ten save
preferences;
1. Press [SAVE1], [SAVE2], [SAVE3] button to load the saved parameter,
for example, load from SAVE2:
LOAD FROM
> SAVE2
2. After about 2 seconds, the LCD shows load finished.
LOAD FROM
> SAVE2 FINISHED!
Note
Same as MENU
SAVE SETUP
LOAD
FROM
VSP 112W
User Manual
112
6. System Setup and Operation
Usage of SD Card and USB
Usage of SD Card and USB
1.SD Card Interface
SD card input interfacing is mainly used to save video program or program
upgrade package.
2.USB1,USB2 Input Interface
USB Media playing input interface could input with USB device or portable
hard disc with USB storage function, which is used to store video program
package.
3.SD Card,USB1 and USB2 Usage Instruction
Usage instruction 1-SD Card: SD Card is priority to USB,SD card video
playing performance is better than USB. When input SD Card and USB in
the same time, system will only play SD card program and in the switching
channels system will also priority switch to SD Card channel.
SD Card requirements: Max. support 32G, format fat/fat32
Usage Instruction 2-U disk: USB1 is under USB2; USB1 is main input,
USB2 is backup input, priority to use USB1
Usage instruction 3-SD Card and U disk priority: When insert SD card and
U disk to VSP 112W in the same time, SD is priority to U disk, which mean
it will only play SD Card video program
Usage Instruction 4-Support video and graphic format;
Support Graphic format: JPGE, BMP, PNG;
Support video format: MP4, MPEG1, MPEG2, RMVB, MJPG, AVI etc.
Usage Instruction 5-Video source downloading: SD card and USB stored
video is from VSP 1123W windows control software 《Red Player Editor》
program editing and releasing
VSP 112W Windows control software;
VSP 112W
User Manual
113
6. System Setup and Operation
Usage of SD Card and USB
After editing Red Player Editor, release the program;
VSP 112W device has connected to SD Card and U disk, Red Player Editor release
and store to VSP 112W
VSP 112W
User Manual
114
6. System Setup and Operation
Usage of SD Card and USB
Select SD Card or U disk
Terminal Equipment is VSP 112W
PC connect to SD card and U disk, Red Player Editor program release and store to
SD card or U disk of PC, then Insert SD card and U disk to VSP 112W.
Select SD Card or U disk
SD card or U Disk in PC
Usage Instruction 6-Program update
If it requires using Red Player Editor to release program to SD card, broadcasting
status must be SD card or U disk. For example, if it requires releasing and uploading
the program to SD card, device must be playing video program in the SD card,
meanwhile upload SD card will update playing program. If program is uploaded to U
disk, playing program will not be updated.
When insert SD card and U disk in the same time in playing condition, remove of
VSP 112W
User Manual
115
6. System Setup and Operation
Usage of SD Card and USB
USB will not affect present broadcasting, SD card is priority to USB, Removing of SD
card will affect present broadcasting, which will need to enter USB menu under
MENU to re-identify USB interface and will broadcaste.
Usage Instruction 7-SD card, U disk video’s audio
If it requires to play audio in SD card or U disk program source, when requires to edit
program, Setup Red Player Editor software video’s audio switching as picture
shows.
1. Select video file
2. Audio switch setup: Yes
And once again confirm if it I mute or volume adjusting through VSP 112w menu.
Menu----AUDIO
MUTE: Mute switch, selectable to off or on the mute
VOLUME: Volume adjustable in 0-100
AUDIO IN: Selectable on audio input source with IMAGE A main image or IMAGE B
sub-image
HDMI: Selectable HDMI audio with INTERNAL or EXTENNAL.
It is also adjustable through windows control software, to set audio.
VSP 112W
User Manual
116
6. System Setup and Operation
Usage of SD Card and USB
VSP 112W
User Manual
117
7. Common Questions and Solutions
In This Chapter
This chapter provides the common questions and solution for the video
processor. The following topics are provided:

No Output in LED Display

Flash Point in LED Display Output

LED Display only Shows Part of the Image

No Display in the Second Half Part of LED Display

Left Screen Appears Two Black Sides
VSP 112W
User Manual
118
No Output in LED Display
Confirm If There is Any Input Signal
Press [MENU] button to find "INPUT" and knob into the "INPUT RES INFO"
to see whether the input signal is normal, suggested the "NO INPUT" signal
does not come in, check the front-end signal lines, and please note to do
dual display or extended in computer ; you can enter other format signals to
view in the same operation.
Confirm If Signal Output
Find a belt VGA input (best for DVI) display, connect to the corresponding
output port of processor, and check whether the signal is correct on the
monitor. If not display properly, please check whether there is input signal,
or if input wire interface is taken tight, output wire interface is picked up
tightly. If display normally, check if sending card is normally working or
need to replace sending card test.
Flash Point in LED Display Output
Confirm If Monitor Output is Normal
Find a belt VGA input (best for DVI) display, connect to the corresponding
output port of processor, and check whether the signal is correct on the
monitor. If display normally shows and no flash point, please check
whether DVI outlets put tight or replace to DVI line of sending card. If
display flashes point, please judge if input signal, wire, and interface are
normal.
VSP 112W
User Manual
119
LED Display Only Displays Part of the Image
Signal Needs to Scale
Press [SCALE] button in the processor and knob to adjust the actual
screen size of the screen, combined with button [POSITION], including the
"width", "height" and "starting position", remember to touch the knob to
confirm.
No Display in the Second Half Part of LED Display
Resolution is Insufficient
Please make sure the points of the screen width and height, choose the
resolution to be bigger than screen width by button [MENU] under
OUTPUT RES, and touch knob to confirm.
Sending Card Can not Take Lower Part
TS 802 can control the max horizontal resolution 2048, and vertical
resolution 640. Each CAT5 output is 320 pixels.
Left Screen Appears Two Black Sides
Adjust DE Deviation
This phenomenon needs to adjust the DVI output and DE migration of the
processor, through the [MENU] to find "OUTPUT" and find the
corresponding output name, such as "DVI1 OUT ADJUST", and find "DVI1
DE" again, make an adjustment for corresponding horizontal and vertical
DE, please remember to save to the corresponding channel after setting up,
save to SAVE1 by default.
VSP 112W
User Manual
120
A. Specification
BNC Input
Number of Inputs
2
Supported Standards
PAL/NTSC
Signal Level
1Vpp±3db (0.7V Video+0.3v Sync ) 75 ohm
Multiplex
480i,576i
VGA DB15 Input
Number of Inputs
1
Connector
Standard DB15 Socket
Supported Standard
VGA-UXGA
Signal Level
R、G、B、Hsync、Vsync:0 to1Vpp±3dB
(0.7V Video+0.3v
Sync ) 75 ohm
black level: 300mV Sync-tip: 0V
Supported Resolution
1024*768*60,
800*600*60,
640*480*60,
1280*720*60,
1280*800*60, 1280*960*60, 1280*1024*60, 1440*900*60,
1400*1050*60, 1600*1200*60, 1680*1050*60, 1920*1080*60,
1366*768*60
DVI Input
Number of Outputs
1
Connector
Standard DVI-I socket
Supported Resolution
SMPTE : 625/25 PAL, 525/29.97 NTSC, 625/50p PAL,
525/59.94p NTSC
1080i50,1080i59.94/60,720p50,720p59.94/60
VESA:800×600×60Hz,1024×768×60Hz,1280×768×60Hz,
1280×1024×60Hz , 1600×1200×60Hz , 1920×1080×60Hz ,
1920×1080×50Hz
Signal Level
TMDS pwl, single pixel input,165MHz bandwidth
Format Standard
HDMI 1.3
USB Input
Number of Inputs
4
Connector
Standard USB port
Supported Standard
Support general image, audio and video formats
DVI Output
Number of Outputs
2
Connector
Standard DVI-I Socket
Signal Level
TMDS pw, 165MHz bandwidth
Supported Resolution
VESA: 800×600×60Hz, 1024×768×60Hz, 1024×768×75Hz,
1280×720×60Hz,
1280×800×60Hz,
1366×768×60Hz,
VSP 112W
1280×720×50Hz,
1280×1024×60Hz,
1400×1050×60Hz,
User Manual
1280×768×60Hz,
1360×768×60Hz,
1440×900×60Hz,
121
1600×1200×60Hz,
1920×1080×50Hz,
1680×1050×60Hz,
1920×1200×60Hz,
2560×812×60Hz,
1920×1080×60Hz,
2048×1152×60Hz,
2560×816×60Hz
VGA Output
Number of Outputs
1
Connector
Standard DB15 Socket
Supported Resolution
VESA: 800×600×60Hz, 1024×768×60Hz, 1024×768×75Hz,
1280×720×60Hz,
1280×800×60Hz,
1366×768×60Hz,
1600×1200×60Hz,
1920×1080×50Hz,
1280×720×50Hz,
1280×1024×60Hz,
1400×1050×60Hz,
1360×768×60Hz,
1440×900×60Hz,
1680×1050×60Hz,
1920×1200×60Hz,
2560×812×60Hz,
Signal Level
1280×768×60Hz,
1920×1080×60Hz,
2048×1152×60Hz,
2560×816×60Hz
R、G、B、Hsync、Vsync:0 to1Vpp±3dB
(0.7V Video+0.3v
Sync ) 75 ohm
black level:300mV Sync-tip:0V
Function
Input channel configuration
Support each
configuration
input
channel
signal
programming
Throughout the year timing
Support throughout the year month, week, day time
Extras
Communication
LAN, front panel and PC software
Power Supply
85-264V 2.1A IEC-3
Working Environment
0°C~45°C
Stored Environment
10% to 90%
Product Warranty
3-year parts and labor warranty
VSP 112W
User Manual
122
Supported 3G USB Adaptor, WIFI and VPN Router List
For the 3G wireless USB network module, we comments to use the following models:
1. Huawei E1750/E1550 (WCDMA);
2. ZTE AC581 (CDMA2000);
3. Huawei E169 (CDMA2000);
4. ZTE AC8710 (CDMA2000);
5. ZTE MU351 (TD-SCDMA).
For the WIFI USB module, we comments to use the following models:
1. TP-LINK TL-WN321G;
2. TP-LINK TL-WN321G+;
3. TP-LINK TL-WN322G+;
4. ASUS WL-167g;
5. TOTOLINK N500UA;
6. OPPO AK093;
7. EDUP N8508.
For the VPN router, we comments to use following model:
1. Netcore NR255 or NR266;
2. VOLANS VE760W or 982W.
VSP 112W
User Manual
123
SER510R/T
Brightness&Temperatures
Integration
Sensor Specification
SER510R/T Introduction
SER510R/T is the intelligent sensor controlled by single chip microcomputer, it can
measure the brightness and temperature of the current environment, and output through
the digital interface, combined with RedPlayerLED display control system, it can realize
the brightness automatically adjustment, also, energy saving effect is remarkable. It has
its own characteristics that high reliability, high precision, and adapt to a wide range, it can
also works long hours in harsh environments.
Typical application: environmental brightness temperature monitoring, LED display screen
brightness automatic controlling, intelligent building lighting temperature controlling, etc.
SER510R/T Features:
● Use digital sensor with high precision, ensure the measurement precision.
● Temperature sensor adopts thermal conductive silicone to fix to the aluminum alloy case,
ensure measure the real temperature.
● Use aluminum alloy casing and high strength transparent plastic cover shell, solid and
reliable.
● Use professional seal water treatment, meet IP67 standard
● SER510R is standard RS - 232 interface, SER510T is TTL level interface.
SER510R/T Technical Indicator
Working Voltage
Minimum
Value
Maximum
Value
Typical
Value
+4.2V
+12V
+5V
Working Current
Note
Measure when work
under +5V
Temperature
Measurement Range
-40℃
120℃
Temperature
Measurement Precision
Brightness
Measurement Range
0.5℃
0lx
216262lx
Brightness
Measurement Precision
3lx
Measurement Period
1s
Working Temperature
-40℃
120℃
Storage Temperature
-55℃
140℃
VSP 112W
User Manual
124
Cable Length
15m
Protection Grade
5m
IP67
SER510R/T Communication Protocol
1. SER510R/T adopts standard DB9 interface, with serial asynchronous communication
mode, baud rate is 9600, start bits is 1, data bits is 8, 1 stop bits is 1, no parity bit.
Pin Description: 2------->TXD
3<-------RXD
5<-----> GND
7------->VDD+5V
2. Data protocols, the sensor will send the brightness and temperature that collected
every second, the formats are as follows:
Header (12 bytes)
Effective
Brightness
Brightness
E5 B2 41 FF 02 00 0A
1 byte
Effective
Temperature
Checksum
2 bytes
2 bytes
Temperature
2 bytes
1 byte
00 73 6E 72 3A
Header is for fixed 12 bytes
Effective Brightness: 01: Effective brightness
00: Invalid brightness
Brightness: High byte front, low byte behind, attenuation coefficient of the cover is about
3.3.
Maximum value of brightness: FFFE, and FFFF means brightness is overflow.
The brightness value of the sensors return multiplied by 3.3 is the current unique
degree of brightness (lx).
Effective Temperature: 01: Effective temperature
00: Invalid temperature
Temperature: High byte front, low byte behind. Integer part of temperature is divide the
value by 10, and the decimal part is remainder. The highest bit is 1 when the temperature
is below zero, and the unit of the temperature is Celsius degrees.
Checksum: Including all the header bytes plus 1.
Data example:
E5B2 41FF0200 0A00736E 723A0107 C6010136 8AFA
E5B2 41FF0200 0A00736E 723A0107 5C010133 F7FA
VSP 112W
User Manual
125
SER510R/T Dimension and Installation
VSP 112W
User Manual
126
B. Contact Information
Warranty:
All video products are designed and tested to the highest quality standard
and backed by a full 3-year parts and labor warranty. Warranties are
effective upon delivery date to customer and are non-transferable. RGBlink
warranties are only valid to the original purchase/owner. Warranty related
repairs include parts and labor, but do not include faults resulting from user
negligence, special modification, lighting strikes, abuse(drop/crush), and/or
other unusual damages.
The customer shall pay shipping charges when unit is returned for repair.
Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial
Development Zone Xiamen, Fujian Province, P.R.C.





VSP 112W
Tel: +86-592-5771197
Fax: +86-592-5771202
Customer Hotline: 4008-592-315
Websites:
~ http://www.rgblink.com
~ http://www.rgblink.cn
E-mail: rgblinkcs@gmail.com
User Manual
127
C. Sending Card Wire Bonding Steps
Here we suggest connect the sending card to the grounding line to prevent
the sending card is burned, specific steps are as follows:
Confirm the sending card and ground wire before welding, shown as follows:
1. Open the top cover, after apart, you can see the yellow earth wire and
sending card position as follows:
VSP 112W
User Manual
128
2. Bonding on the sending card metal shell, the position is shown in figure:
3. The picture after bonding is shown as follows:
VSP 112W
User Manual
129
4. Welding the end that not fixed of the earth wire to the soldering position.
5. The picture after bonding is shown as follows:
6. After bonding, lock the top cover.
VSP 112W
User Manual
130