ERNT-ASQTD62 User`s Manual

Mitsubishi General-Purpose Programmable Controller
Renewal Tool
Conversion Adapter
Model
[Wiring Precautions]
3.Product Specifications
CAUTION

Carry out wiring for the Conversion Adapter correctly after checking the specification and
terminal arrangement for the module used. Connecting a power supply with a different voltage
rating or incorrect wiring may cause a fire or failure.

Tighten the MELSEC-AnS Series terminal installation screws and terminal screw securely by
applying torque within the specified limits. Loose screws will cause short circuit, fire or
malfunction. Excessive tightening will damage the screws or the Conversion Adapter which in
turn will cause dropping of parts, short circuit or malfunction.

Use care to prevent foreign materials including cuttings and wiring debris from entering the
Conversion Adapter or the MELSEC-Q Series Module. These will be cause for fire, failure or
malfunction.
ERNT-ASQTD62
User’s Manual
[Startup and Maintenance Precautions]
WARNING
50CM-D180122-C(1409)

Do not touch live terminals. There is a danger of electric shock or malfunction.

Shut off the external power supply for the system in all phases before cleaning or retightening
the terminal screws. Failure to do so may result in electric shock or cause the MELSEC-Q
Series module to fail or malfunction. Loose screws can lead to dropping, shorting, and
malfunction. Excessive tightness of the screws can lead to breakage of the screws, Conversion
Adapter, Mounting Bracket, or MELSEC-Q Series Module, possibly causing the dropping,
shorting, and malfunction thereof.
HEAD OFFICE:Hulic KUDAN BLDG.1-13-5,KUDANKITA CHIYODA-KU,TOKYO 102-0073,JAPAN
NAGOYA ENGINEERING OFFICE:139 SHIMOYASHIKICHO-SHIMOYASHIKI,KASUGAI,AICHI 486-0906,JAPAN
 SAFETY PRECAUTIONS 
CAUTION
(Always read these precautions prior to use.)
Before using this product, please read this manual carefully and pay full attention to safety to ensure
that the product is used correctly.
The precautions presented in this manual are concerned with this product only. For Programmable
Controller system safety precautions, refer to the user’s manual of the MELSEC-Q series CPU
module to be used.
In this manual, the safety precautions are ranked as “WARNING” and “CAUTION.”
WARNING
Indicates that incorrect handling may cause hazardous conditions,
resulting in death or severe injury.
CAUTION
Indicates that incorrect handling may cause hazardous conditions,
resulting in medium or minor injury and/or property damage.
Note that failure to observe the
CAUTION level instructions may lead to a serious consequence
according to the circumstances. Always follow the precautions of both levels because they are
important to personal safety.
Please keep this manual in an easy-to-access location for future reference, and be sure to provide the
manual to the end user.
[Precautions before using]
CAUTION
 When making a switch from the MELSEC-AnS Series to the MELSEC-Q Series, be sure to
consult user's manual supplied with individual module under the MELSEC-Q Series to
confirm differences in various aspects including performance and function between the two
series.
[Installation Precautions]
CAUTION
 Use the Conversion Adapter in the environmental conditions that are specified in the general
specification. If the Products are used in any environment beyond the bounds of the general
specification, electric shock, fire, malfunction, or damage to or degradation of the Products
will result.
 Do not directly touch any conductive parts of Conversion Adapter. Contact will cause
malfunction or failure in the system.
 Fasten the Conversion Adapter and the Mounting Bracket securely with retaining screws,
and tighten the screws by applying torque within specified limits. Loose screws can lead to
the dropping of the Conversion Adapter or Mounting Bracket, possibly causing breakage
thereof. Excessive tightness of the screws can lead to breakage of the screws, Conversion
Adapter, Mounting Bracket, or MELSEC-Q Series Module, possibly causing the dropping,
shorting, and malfunction thereof.

Do not modify the Conversion Adapter or take it apart. Doing so will cause failure,
malfunction, personal injury, or fire.

Do not drop the Conversion Adapter and Mounting Bracket or do not give a strong impact to
it. This will cause damage.
When installing the Conversion Adapter, take care not to get your hand snagged on the
Mounting Bracket or the like. Injury may result.

When installing or removing the MELSEC-Q Series Module complete with a Converter
Adapter, be sure to hold it with both hands. Dropping may lead to breakage.
[Wiring Precautions]
Before attempting to install the Unit or carry out the necessary wiring, make certain that the
external power supply, used in the system, is shut off on all three phases. Failure to do so
may result in electric shock or damage to the product.

After installation and wiring, close the terminal block cover before turning on the module for
operation. Failure to do so may result in electric shock.
*1
Signal Name
Phase A
5/12/24V
COM
24V
φA 12V
5V
5/12/24V
C
Phase B
H
COM
1 PRST 5/12/24V
C
H
2
C
H
1
C
H
2
Setting pin
24V
φB 12V
5V
24V
PRE 12V
5V
CTRL COM
FUNC 5/12/24V
5/12/24V
Phase A
COM
5/12/24V
Phase B
COM
PRST 5/12/24V
CTRL COM
FUNC 5/12/24V
EQU1
EQU2
EQU1
EQU2
12/24V
0V
24V
F ST 12V
5V
24V
φA 12V
5V
24V
φB 12V
5V
24V
PRE 12V
5V
24V
F ST 12V
5V
CAUTION

When disposing of the product, treat it as industrial waste.
EMC AND LOW VOLTAGE DIRECTIVES
Authorized representative in Europe
Model
Counting speed switch settings
Count input
signal
Product
1
1
Mounting bracket fixing screw (M2.6×4)
Fixture installation screw (M3×8)
Terminal block cover
Short bar (spare parts)
2
1
1
1
Installation location
Overvoltage category *2
12V Input: set to 12V side
5V Input: set to 5V side
Inputting a voltage higher than the one set using the setting pins may cause a failure in the
MELSEC-Q Series module.
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
Coincidence
output
10k
100kPPS
7kPPS
Specification
External
Coincidence output
output
I/O occupied points
Wiring connection system
Internal current consumption(5VDC)
-25 to 75℃
5 to 95%RH,non-condensing
Make sure the
Sweep
count
Under
5 to 8.4Hz
3.5mm
10 times each in
intermittent
2
-
X, Y, Z directions
8.4 to 150Hz
9.8m/s
vibration
-
Under
5 to 8.4Hz
1.75mm
-
continuous
2
-
8.4 to 150Hz
4.9m/s
vibration
2
Compliant with JIS B 3502 and IEC 61131-2 (147 m/s , 3 times each in 3 directions X, Y, Z)
No corrosive gases
0 to 2000m
Inside a control panel
II or less
Pollution degree *3
2
*1:Do not use or store under pressure higher than the atmospheric pressure of altitude 0m.
*2:This indicates the section of the power supply to which the equipment is assumed to be connected between the public
electrical power distribution network and the machinery within premises.
Category II applies to equipment for which electrical power is supplied from fixed facilities.
*3:This index indicates the degree to which conductive material is generated in terms of the environment in which the
equipment is used.
Pollution level 2 is when only non-conductive pollution occurs. A temporary conductivity caused by condensing must be
expected occasionally.
2 to 5mA
200kPPS *1
24-bit binary (0 to 16777215)
5μs
5μs
Comparison range
Comparison result
Preset
Function start
Model
Half
amplitude
10kPPS
10μs
Specifications
0 to 55℃(Maximum surrounding air temperature 55℃)
Constant
acceleration
-
MELSEC-Q Series
QD62
QD62E
Switch with the intelligent function module switch setting
200k
100k
10k
(100k to 200kPPS)
(10k to 100kPPS)
(10kPPS or less)
2 channels
1-phase input (1 multiple/2 multiples),
2-phase input (1 multiple/2 multiples/4 multiples),
CW/CCW input
5/12/24VDC
Minimum count
pulse width
(Duty ratio 50%)
Eternal input
Frequency
Operating atmosphere
Operating altitude *1
B20
B19
B18
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
100kPPS
(1-phase and 2-phase
inputs)
2.General Specifications
Shock resistance
Set the pins of each signal(φA,φB,PRE,F ST)according to the input voltage.
The default input voltage for all signals is 24V(24V side).
24V Input: set to 24V side
QD62
QD62E
Connector
Signal level
(φA,φB)
Counting
speed
(max)
Quantity
Conversion Adapter
Mounting bracket
Compliant with
JIS B 3502 and
IEC 61131-2
*1
1-phase input,
2-phase input
Phase
Counter
Once you have opened the packaging, verify that it contains the following products.
Vibration
resistance
C
H
1
C
H
2
100k
1-phase
input
2-phase
input
Counting range
Model
This manual provides information about the Conversion Adapter “ERNT-ASQTD62” available as
Renewal Tools for the Mitsubishi General-Purpose Programmable Controller.
The Conversion Adapter is a product for effecting conversion to transcend difference in pin assignment
between the MELSEC-AnS Series and the MELSEC-Q Series.
Before attempting to make a switch from MELSEC-AnS Series to MELSEC-Q Series in your installation,
consult the user's manual supplied with individual module under the latter series to learn about how
they differ in various aspects including performance and function.
Storage ambient
temperature
Operating ambient
humidity
Storage ambient
humidity
C
H
2
Precautions for wiring
MELSEC-AnS Sereis
A1SD62
A1SD62E
Switch with the setting pins
Specification
1.Overview
Item
C
H
1
Signal
Name
Phase A 24V
Phase A 12V
Phase A 5V
AB COM
Phase B 24V
Phase B 12V
Phase B 5V
PRST 24V
PRST 12V
PRST 5V
CTRL COM
FUNC 24V
FUNC 12V
FUNC 5V
Phase A 24V
Phase A 12V
Phase A 5V
AB COM
Phase B 24V
Phase B 12V
Phase B 5V
PRST 24V
PRST 12V
PRST 5V
CTRL COM
FUNC 24V
FUNC 12V
FUNC 5V
EQU1
EQU2
EQU1
EQU2
Open
Open
Open
Open
0V
12/24V
0V
12/24V
Number of channels
Authorized representative in Europe is shown below.
Name: Mitsubishi Electric Europe BV
Address: Gothaer strasse 8, 40880 Ratingen, Germany
Operating ambient
temperature
Terminal
No.
A20
B20
A19
B19
A18
B18
A17
B17
A16
B16
A15
B15
A14
B14
A13
B13
A12
B12
A11
B11
A10
B10
A9
B9
A8
B8
A7
B7
A6
B6
A5
B5
A4
B4
A3
B3
A2
B2
A1
B1
< Specification comparison >
Compliance to the EMC Directive, which is one of the EU Directives, has been a legal obligation
for the products sold in European countries since 1996 as well as the Low Voltage Directive since
1997.
Manufacturers who recognize their products are compliant to the EMC and Low Voltage
Directives are required to declare that print a "CE mark" on their products.
WARNING

Internal circuit diagram of ERNT-ASQTD62
Terminal
No.
TB1
TB2
TB3
TB4
A1SD62
TB5
A1SD62E
TB6
Terminal Block
TB7
TB1
TB2
TB8
TB3
TB4
TB9
TB5
TB6
TB10
TB7
TB8
TB11
TB9
TB10
TB12
TB11
TB12
TB13
TB13
TB14
TB14
TB15
TB16
TB15
TB17
TB18
TB16
TB19
TB20
TB17
TB18
TB19
TB20
[Disposal Precautions]
 Always check for correct match between MELSEC-Q Series and the Conversion Adapter.
Incorrect match can cause damage to the MELSEC-Q Series Module.

For detail specifications which do not appear in the specification comparison charts contained herein, see the user's manual supplied with the MELSEC-Q Series module you use. Those parts of the specification that
differ between the MELSEC-AnS Series and the MELSEC-Q Series are where a switch from the first series to the second is subjected to specification-related restrictions. Check the specification of the devices to be
connected for more details.
Furthermore, it is recommended to refer to the “Transition from MELSEC-AnS/QnAS (Small Type) Series to Q Series Handbook (Intelligent Function Modules): L (NA)-08220ENG” issued by Mitsubishi Electric.
Conversion
Conversion Adapter
MELSEC-AnS Series
No. of
MELSEC-Q Series
Adapter
Model
Model
channels
Model
Weight (g)
A1SD62
2 channels
QD62
ERNT-ASQTD62
110
QD62E
A1SD62E
2 channels
50μs
(1-phase input)
10kPPS *1
32-bit singed binary (-2147483648 to 2147483647)
UP/DOWN Preset counter + Ring counter function
5μs
142μs
100μs
50μs
100kPPS *1
71μs
2.5μs
71μs
2.5μs
Min. phase differential for
2-phase input:1.25μs
(2-phase input)
10μs
5μs
5μs
Min. phase differential for
2-phase input:2.5μs
100μs
50μs
50μs
Min. phase differential for
2-phase input:25μs
24-bit binary
32-bit singed binary
Set value < Count value, Set value = Count value, Set value > Count value
5/12/24VDC
MELSEC-AnS Series
A1SD62
A1SD62E
Transistor (sinking type) output
Transistor (sourcing type) output
12/24VDC 0.1A/point 0.4A/common
12/24VDC 0.5A/point 2A/common
32 points
20 point terminal block
0.1A
2 to 5mA
MELSEC-Q Series
QD62
QD62E
Transistor (sinking type) output
Transistor (sourcing type) output
12/24VDC 0.1A/point 0.4A/common
12/24VDC 0.5A/point 2A/common
16 points
40-pin connector
0.30A
0.33A
section of the above table meets the specification of the machines and equipment connected to the MELSEC-Q Series module.
*1:Counting speed is affected by pulse rise and fall time. Possible counting speeds are shown in the following table.
Note that if a pulse that has a large rise and /or fall time is counted, a miscount may occur.
Counting speed
Both 1-phase and 2-phase input
switch settings
200k
100k
10k
Rise/fall time
t = 1.25μs or less
t = 2.5μs or less
t = 25μs or less
t = 500μs
200kPPS
100kPPS
-
-
100kPPS
100kPPS
10kPPS
-
10kPPS
10kPPS
10kPPS
500PPS
t
t
Precautions for the program
1. A1SD62/A1SD62E and QD62/QD62E differ from each other in the way input/output signals (X, Y) and buffer memory addresses are allocated. Therefore, you need make necessary changes to the sequence
program that is used.
2. Set the counting speed using the intelligent function module switch setting in the QD62 and QD62E instead of the setting pins that are used in the A1SD62 and A1SD62E.
4.Mounting and Installation
5.Preparation before Installation
4.1 Handling Precautions
5.1 Position of the setting pins
1
2 Set the setting pins (short bar) as necessary.
1) Set the pins in order from one side(CH1φA or
CH2F ST)to avoid the incorrect setting.
2) Insert the short bar all the way into the setting pins
in place till it can not be moved.
Open the cover.
Open the cover of the Conversion Adapter, and you will find the setting pins to switch the input signal
voltage.
【With the cover closed】
【With the cover opened】
Cover
Protective wrap
24V
12V
5V
Unit:mm
3 Make sure they have been set
correctly and close the cover.
Protective wrap
2
Setting pin
CH2
MELSEC-AnS
Series
MELSEC-Q
Series
Mounting bracket fixing screw M2.6×4
(supplied with Conversion Adapter)
Set the input voltage for each signal using the short bar.
The short bar can be installed from any direction.
Ԁᣖltage
5V
Signal
CH1
φB PRE F ST
φA
CH2
φB PRE F ST
69mm
70
MELSEC-AnS Series
terminal block installation screw (M4)
Conversion Adapter installation screw
M3×20
Conversion Adapter
Make sure to set the setting
pins before installation.
φA
CH2
φB PRE F ST
PRE F ST
PRE F ST
PRE F ST
PRE F ST
PRE F ST
24V
12V
5V
24V
12V
5V
24V
12V
5V
24V
12V
5V
24V
12V
5V
Incorrect settings for 12V input Incorrect settings for 24V input
24V
12V
5V
CH2
φB PRE F ST
CH2
φB PRE F ST
CH2
φB PRE F ST
24V
12V
5V
24V
12V
5V
24V
12V
5V
Short circuit between different signals
PRE F ST
PRE F ST
Short circuit
between 12V and 24V
24V
12V
5V
24V
12V
5V
24V
12V
5V
24V
12V
5V
No short bar installed
PRE F ST
PRE F ST
PRE F ST
27.4mm
For details of the installation environment, refer to the user’s manual of the MELSEC-Q series CPU
module to be used.
φA
Incorrectly setting the setting pins will cause a failure and malfunction. Make sure to set them
correctly.
Incorrect settings for 5V input
4.3 Installation Environment
CH1
φB PRE F ST
65mm
6
Short circuit
between 5V and 12V
17.55
【Installation with the DIN rail】
DIN rail
※
Conversion Adapter DIN rail mounting bracket (right)
MELSEC-Q Series
Base Unit
Mounting bracket
(supplied with Conversion Adapter)
Mounting bracket fixing screw M2.6×4
(supplied with Conversion Adapter)
Precaution
2
MELSEC-AnS Series terminal block
MELSEC-AnS Series
terminal block cover
(supplied with Conversion Adapter)
Product Warranty Details
3
5
※
MELSEC-Q Series Module
Conversion Adapter
DIN rail mounting bracket (bottom)
Fixture
(has been installed to the Conversion Adapter)
6
※The separately-sold Conversion adapter
DIN rail mounting bracket (ERNT-ASQDIN)
is required to use this Conversion Adapter.
Refer to the user's manual of the DIN rail
mounting bracket of the Conversion
Adapter for the installation method.
MELSEC-AnS Series
terminal block installation screw (M4)
Conversion Adapter installation screw
M3×20
Conversion Adapter
Make sure to set the setting
pins before installation.
6.1 Installation Method
Installation with the Base Adapter
Mount the MELSEC-Q Series
Base Unit to the Base Adapter.
Refer to the Base Adapter's
manual for how to install them to
the control panel.
Please confirm the following product warranty details prior to product use.
Gratis Warranty Terms and Gratis Warranty Range
4
Fixture installation screw M3×8
(supplied with Conversion Adapter)
Notice
24V
12V
5V
Replace the terminal
block cover with the
one supplied with the
Conversion Adapter.
F ST
PRE F ST
Terminal block cover for
the MELSEC-AnS Series
φB
CH2
CH2
φB PRE F ST
φA
PRE
<MELSEC-Q Series>
Terminal block cover
4
1
φA
Conversion Adapter
DIN rail mounting
bracket
24V
(Factory setting)
12V
φA
PRE
F ST
44.5mmUP
<MELSEC-AnS Series>
5
Fixture installation screw M3×8
(supplied with Conversion Adapter)
CH1
φB PRE F ST
φB
CH1
Conversion Adapter
150.5mm
3
Fixture
(has been installed to the Conversion Adapter)
φA
4mmUP
MELSEC-AnS Series terminal block
Precaution
Mounting bracket
2
5.2 How to set the setting pins
MELSEC-Q
Series
The terminal block cover for MELSEC-AnS Series is bigger than the width of
the MELSEC-Q Series Module. Therefore, it is necessary to replace it with the
terminal block cover supplied with the converter adapter.
34.5mm
MELSEC-Q Series
Base Unit
MELSEC-AnS Series
terminal block cover
(supplied with Conversion Adapter)
φA
Installation with the DIN rail
Because the module is increased in depth and height dimension, check
dimensional data before installing the module.
106mm
Mounting bracket
(supplied with Conversion Adapter)
It is used to protect your hands from touching the conductive part in the pin-setting process.
(1) Peel it off after finishing the settings.
(2) Make sure to peel it off before installing a MELSEC-AnS Series terminal block.
157.5mm
4mm
Base Adapter
To the control panel
About the protective wrap
47.5mmUP
MELSEC-AnS
Series
27.4
【Installation with the Base Adapter】
24V
MELSEC-Q Series Module
Base Adapter
Terminal block
cover
6.Part Names and Installation Method
Set the input voltage for A-phase pulse of CH1.
Set the input voltage for B-phase pulse of CH1.
Set the input voltage for Preset input of CH1.
Set the input voltage for Function start input of CH1.
Set the input voltage for A-phase pulse of CH2.
Set the input voltage for B-phase pulse of CH2.
Set the input voltage for Preset input of CH2.
Set the input voltage for Function start input of CH2.
φA
φB
PRE
F ST
φA
φB
PRE
F ST
1
Conversion
Adapter
110mm
Factory
setting
Description
27.4mm
Installation with the Base Adapter
Because the module is increased in depth dimension, check dimensional data
before installing the module.
1
CAUTION
! 注意 CAUTION
Short bar
102
Setting pin
CH1
Depth and Height
dimension
4 Hold the protective wrap with its rear side towards the
right and peel it off towards yourself before installing a
MELSEC-AnS Series terminal block.
Cover
<MELSEC-Q Series>
34.5mm
7.External Dimensions
31.5
<MELSEC-AnS Series>
Short bar
82.1
Use Precautions
Because the module is reduced in width dimension (34.5mm→27.4mm) and
thus in area available for wiring, check dimensional data before installing the
module.
Tighten the module installation screws to the specified torque below. An inappropriate tightening torque
could cause the product to fall or result in a short circuit, product failure or malfunction.
Screw Location
Tightening Torque Range
Mounting bracket fixing screw (M2.6×4)
0.20 to 0.29N・m
Conversion Adapter installation screw (M3×20)
0.43 to 0.57N・m
Fixture installation screw (M3×8)
0.61 to 0.82N・m
MELSEC-AnS Series terminal block installation screw (M4 screw)
0.78 to 1.18N・m
Setting pin
4.2 Use Precautions
Item
Width dimension of
module
! 注意 CAUTION
! 注意 CAUTION
! 注意 CAUTION
CH2
φB PRE F ST
Make sure to set
the setting pins
(short bar) before
installation.
CH1
φB PRE F ST φA
Cover
φA
! 注意 CAUTION
Protective wrap
Display nameplate
CH2
CH1
φA φB PRE F ST φA φB PRE F ST
(1) Before attempting to install the Unit or carry out the necessary wiring, make certain that the
external power supply, used in the system, is shut off on all three phases. Failure to do so may
result in electric shock or damage to the product.
(2) Do not touch live terminals. There is a danger of electric shock or malfunction.
(3) Do not modify the Conversion Adapter or take it apart. Doing so will cause failure, malfunction,
personal injury, or fire.
(4) Do not touch the energized part of the Conversion Adaptor directly. Contact will cause malfunction
or failure in the system.
(5) The protective wrap is used to protect your hands from touching the conductive part in the
pin-setting process. Peel it off after finishing the settings. In addition, make sure to peel it off before
installing a MELSEC-AnS Series terminal block.
(6) Fasten the Conversion Adapter and the Mounting bracket securely with retaining screws, and
tighten the screws by applying torque within specified limits. Loose screws can lead to the
dropping of the Conversion Adapter, or Mounting bracket, possibly causing breakage thereof.
Excessive tightness of the screws can lead to breakage of the screws, Converter Adapter,
Mounting bracket or MELSEC-Q Series Module, possibly causing the dropping, shorting, and
malfunction thereof.
(7) Use care to prevent foreign materials including cuttings and wiring debris from entering the
Conversion Adapter or the MELSEC-Q Series Module. These will be cause for fire, failure or
malfunction.
(8) Do not drop the Conversion Adapter and Mounting Bracket or do not give a strong impact to it. This
will cause damage.
6.2 Tightening Torque
5.3 Procedure
Installation with the DIN rail
Mount the MELSEC-Q Series Base Unit to the DIN rail
mounting bracket of the Conversion Adapter and the
adapters for DIN rail installation manufactured by
Mitsubishi Electric.
For how to mount them to the DIN rail, refer to the user’s
manual of the Conversion Adapter DIN rail mounting
bracket and QCPU.
1 Mount the MELSEC-Q Series module to the MELSEC-Q Series Base Unit.
2 Secure the Mounting Bracket to a compatible module under the MELSEC-Q Series with
Mounting Bracket fixing screws (M2.6 x 4). (2 places)
3 Install the Conversion Adapter to the MELSEC-Q Series module, and secure it with the
Conversion Adapter installation screws (M3×20). (2 places)
Precaution
Before tightening the installation screws, check that the Conversion Adapter has been
securely installed on the MELSEC-Q Series module. Tightening the screws in floating-off
state or tilting state will damage the Conversion Adapter installation screws and the
mounting bracket.
4 Secure the fixture to the Base Adapter or Conversion Adapter DIN rail mounting bracket
(bottom) of the Conversion Adapter with fixture installation screws (M3 x 8). (1 place)
5 Secure the MELSEC-AnS Series terminal block to the Conversion Adapter with the supplied
terminal block installation screw (M4). (2 places, top and bottom.)
If any fault or defect (hereinafter referred to as “Failure”) attributable to Mitsubishi Electric Engineering
Company Limited (hereinafter referred to as “MEE”) should occur within the gratis warranty period, MEE
shall repair the product free of charge via the distributor from whom you made your purchase.
 Gratis Warranty Period
The gratis warranty period of this product shall be one (1) year from the date of purchase or
delivery to the designated place.
Note that after manufacture and shipment from MEE, the maximum distribution period shall be six
(6) months, and the gratis warranty period after manufacturing shall be limited to eighteen (18)
months.
In addition, the gratis warranty period for repaired products shall not exceed the gratis warranty
period established prior to repair.
 Gratis Warranty Range
The gratis warranty range shall be limited to normal use based on the usage conditions, methods
and environment, etc., defined by the terms and precautions, etc., given in the instruction manual,
user’s manual and caution labels on the product.
Warranty Period after Discontinuation of Production
(1) MEE shall offer product repair services (fee applied) for seven (7) years after production of the
product has been discontinued. Discontinuation of production shall be reported via distributors.
(2) Product supply (including spare parts) is not possible after production has been discontinued.
Exclusion of Opportunity Loss and Secondary Loss from Warranty
Liability
Regardless of the gratis warranty period, MEE shall not be liable for compensation for damages arising
from causes not attributable to MEE, opportunity losses or lost profits incurred by the user due to
Failures of MEE products, damages or secondary damages arising from special circumstances, whether
foreseen or unforeseen by MEE, compensation for accidents, compensation for damages to products
other than MEE products, or compensation for other work carried out by the user.
Changes in Product Specifications
The specifications given in the catalogs, manuals and technical documents are subject to change
without notice.
This document is a new publication, effective September 2014. Specifications are subject to change
without notice.
6 Remove the terminal block cover from the MELSEC-AnS Series terminal block and fit the
terminal block cover supplied with the Conversion Adaptor in place.
Developed September 2014
50CM-D180122-C