USER MANUAL LL STAGE SPOT VARIO OPTIC

Leader Light s.r.o.
M.Gorkeho 33
SK-052 01 Spisska Nova Ves
Slovakia
www.leaderlight.eu
USER MANUAL
LL STAGE SPOT VARIO OPTIC
Without optic: LL36 203
01
Safety Information
02.2 Back panel
DMX Out
XLR-5pin
WARNING!!!
Carefully read before installing, powering or servicing.
Nothing to do if anything misunderstand! Installation can be done only
by a qualified professional in accordance with relevant local codes.
POWER
- Do not look directly into LED lamps.
- Do not look into light beam from a distance of less than 40 cm (16 inches)!
COMPLIMENTS ON YOUR PURCHASE!
POWER
DMX512
01.1 Risk of eyes damage
With optic: LL36 202
DMX In Power In
XLR-5pin PowerCon
Control LEDs
DATA
MODE & ADDRESS
01.2 Protection from electric shock
All dimensions are in millimeters
215
- Shut down power before installation or maintenance.
- Luminaries and recommended AC power supply must be installed by a qualified
professional in accordance with relevant local codes. Only acceptable source of AC power
and frequency that complies with local building and electrical codes to use.
- Do not use or do not connect the products if the power cable, power plug or fixtures are any
way damaged, wet, or if they are overheating.
- Do not modify, alter, or attempt to service the LeaderLight appliance. Doing so will void the
warranty.
- Before removing or installing any cover or part of appliance disconnect it from AC power.
- Appliance always connect to earth (eltech.).
163,2
195
Dip options “100“ “10“ “1“ » Rotating DIP address 000÷511
Control LEDs Indication
01.3 Fire prevention
Following items are included:
1. LL STAGE SPOT VO without optic
- LL STAGE SPOT 16 RGBA , without optic
- PowerCon type “A“ + “B“
- User manual
2. LL STAGE SPOT VO with optic
- LL STAGE SPOT 16 RGBA , without optic
- LL VARIO OPTIC SPOT 16 25°
- PowerCon type “A“ + “B“
- User manual
1 pc.
1 pc.
1 pc.
1 pc.
1 pc.
1 pc.
1 pc.
WARNING!!!
!
Additional items needed:
- Data cables with XLR 5pin Female/Male
- Controller compatible with DMX
- Mounting accessories as necessary
Surface mounting:
- Screws and washers 1xM12 or 2xM10
Content:
01 SAFETY INFORMATION
01.1 Risk of eyes damage
01.2 Protection from electric shock
01.3 Fire prevention
02 Product Specification
02.1 Technical Specification
02.2 Back panel
03 Installation
03.1 Unpacking
03.2 Physical installation
03.3 Connecting to AC power
03.4 Control data connecting
03.5 DMX channels
04 Maintenance
Environment
Do not throw away the appliance with the normal household waste at the end
of its life, but hand it in at an official collection point for recycling. By doing
this, you help to preserve the environment.
©MMX - Leader Light – All right reserved
1 pc.
1 pc.
!
Non-minimum distance and / or non-use the original brackets is at your own risk!
02 Product Specification
02.1 Technical Specification
Lamp type:
Lifetime:
Vario Optic:
Control data connection:
Input power:
Power connection:
Net weight:
IP:
Ambient temp. (Ta):
Cooling:
Materials and finish:
Installation:
* Note: LED:
LED
INDICATION
STATUS
POWER (Red)
blinking – 2Hz
OK - inside fixture is everything correct
DATA (Green)
light off
NO DMX512 signal
DATA (Green)
blinking – 4Hz
OK- income correct DMX512 signal
DATA (Green)
fast blinking
NON correct digital signal
alternate blinking
Autotest function
POWER (Red)
- Follow all safety consideration.
- Thermostatic switches or fuses never to bypass.
- Device never shield. Around the axis of the fitting (180°) must be maintained space for
cooling. Minimum distance from the surrounding objects must be 100mm (4 in.) (figure 1.1).
- LEDs never direct cover with filters or other materials.
- Allowing max. ambient temperature is 40°C (104°F).
- Luminaries never use without mounting brackets. The housing never install directly to the
surface.
16xRGBA OneChip LED *
Long 60 000 hrs 90% degradation
10°, 25°, 40° and EL (Eliptical 15°x90°)
DMX 512 In/Out with 5pin XLR
POWER
DATA (Green)
03 Installation
03.1 Unpacking
- Unpack carefully.
- This is electronic equipment and should be handled carefully.
- Damaged delivered package or if are any mechanical parts broken – it must be claim
immediately by the transport company. Photo pictures as evidence are valuable for
future claim.
03.2 Physical installation
- Loading capacity of bearing area has to be at least 10 times the weight of all device
clusters (luminaries, clamps, cables, ...).
- Hairbreadth from combustible materials is 0,5m.
- Before physical installation insert the optic modul on front of luminary. The optic
installation is easy and fast by 1 screw (figure Nr. 2.1).
03.3 Connecting to AC power
-
To tackle all Safety Information- 01!
For protection from electric shock, the device must be grounded (earthed)!
It is not necessary to open the fixture before power supply.
Power supply is solved simple with Neutrik PowerCon connectors.
The fixture is equipped with auto-switching power supply that automatically adjusts to
any 50-60Hz AC power source from 100-260V.
- Cord plug connections:
Symbol
Pin
Wire Colour
Screw (US)
150W
L
live
brown
yellow or brass
100-260V AC In/Out PowerCon
N
neutral
blue
silver
ground (earth)
yellow/green
green
3kg
IP20
Maximum 40°C
Conventional
Housing: powder-painted anodized aluminium in black
(other colours on request)
Surface mounting
RGBA-Red and Green and Blue and Amber
Edition: A - 2010
DATA
03.4 Control data connecting
- Control data cable length is specified by Norm IEC929 Annex E4.
- It is not necessary to open the fixture before connecting of DMX512 control signal.
Interconnections are realized by Neutrik XLR 5pin IN/Out connectors.
- Pin connections:
Pin 1 – ground
Pin 2 – signal negative
Pin 3 – signal positive
If you have any question please, contact support@leaderlight.sk
03.5 DMX channels - subject to change
INSTALLATION space
- The latest version of DMX channels appendix are on the websites - www. leaderlight.eu
Ventilation space 180° free
DMX channels:
Switch functions Dip4:
dmx1
= Red
Dip1
= ExtMode (+2 ch.: Master, Strobo)
dmx2
= Green
Dip2
for future
dmx3
= Blue
Dip3
for future
dmx4
= Amber
Dip4
= Ultra soft curve
dmx5
= Master (Dip1=On)
dmx6
= Strobo (Dip1=On)
Ventilation space 90° free
minimal.
100mm
minimal.
80mm
minimal.
80mm
minimal.
80mm
Minimal mounting distance from surface
1.1
Surface installation
Screw the fixture to the surface (M12 or 2xM10)
180°
180°
AIMING POSSIBILITY
The fixture could be aim to wish
position with bracket.
Unfix by hand the screw and aim the fixture to the wish position and fix.
1.2
Vario Optic installation
It is not necessary to open the fixture for echange of Vario Optic
04 MAINTENANCE
- To tackle all Safety Information- 01!
- Damage caused by inadequate cleaning or maintenance is not coverd by
warranty.
- Regular cleaning is demand (dust, dirt, ...)
Maintenance policy:
- Unplug mains before maintenance and at least 10 minutes cool off
- Appliance do not illegal open or demount
- Clean-up dust only from outer surface (for ex. scuttle, diffuser and lenses).
- Use vacuum or dumpy duster (warm water)
- Before reinstalling to check failure-free state – no wet parts!
Order code
Product name
LL36 202
LL STAGE SPOT 16 RGBA VO, 25°
LL36 203
LL STAGE SPOT 16 RGBA , without optic
Accessories:
LL VARIO OPTIC SPOT 16
The optic installation is easy and fast by 1 screw. Carefully remove the optic modul and
insert the new one and fix with screw.
2.1
If you have any question please, contact support@leaderlight.sk
LL37 190
LL VARIO OPTIC SPOT 16 10°
LL37 191
LL VARIO OPTIC SPOT 16 25°
LL37 192
LL VARIO OPTIC SPOT 16 40°
LL37 193
LL VARIO OPTIC SPOT 16 EL (Eliptical 15°x90°)