EQ900 eZ.HD Series
720p Analog High Definition
True Day/Night Box Camera
User’s Manual
** Lens not included.
Copyright © EverFocus Electronics Corp,
Release Date: Nov., 2014
Precautions
Please read this manual first to ensure correct installation and operation. This manual should be
retained for future reference. The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All specifications are
therefore subject to change without notice.
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV / radio transmitters, magnets, electric motors, transformers
and audio speakers, because the electromagnetic fields generated by these devices may
distort the video image or otherwise interfere with camera functions.
2. Never disassemble the camera beyond the recommendations in this manual, nor apply
materials to it other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure
or other damage.
3. Try to avoid pointing the camera toward the sun.
In some circumstances, direct sunlight may cause permanent damage to the sensor and / or
internal circuits. It may also create unbalanced illumination that may be beyond the
camera’s ability to compensate.
4. Keep the power cable away from water and other liquids. Never touch the power cable
with wet hands.
Touching a wet power cable with your hands or touching the power cable with wet hands
may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may cause equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly
with your hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the
sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera body.
Do not use complex solvents, or corrosive or abrasive agents to clean any part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity and power source
levels. This camera is suitable for indoor operation only.
Use the camera at temperatures within -10°C ~ 50°C (14°F ~ 122°F) and humidity between
20 ~ 80%; this device is not rated as submersible. The input power source should be 12VDC
or 24VAC. The use of a properly fused or “Class 2 Limited Power Source” power supply is
highly recommended.
8. Mounting
Select a solid mounting surface that will support the weight of the camera and any
additional loading from wind, snow, ice or other factors. Securely attach the camera to the
mounting surface using screws and anchors that will properly support the camera. If
necessary, (e.g. when mounting the camera to a drop ceiling, or unsupported ceiling) use a
safety wire to provide additional support for the camera.
i
Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
ATTENTION!
This is a class A product which may cause radio interference in a domestic
environment; in this case, the user may be urged to take adequate measures.
This Product is RoHS compliant.
Your EverFocus product is designed and manufactured with high quality materials and
components which can be recycled and reused. This symbol means that electrical and
electronic equipment, at their end-of-life, should be disposed of separately from your
household waste. Please, dispose of this equipment at your local community waste
collection/recycling centre. In the European Union there are separate collection systems for
WEEE
used electrical and electronic product.
Please, help us to conserve the environment we live in!
ii
Contents
1.
Introduction .................................................................................................................. 1
1.1 Packing List ........................................................................................................................... 1
1.2 Features................................................................................................................................ 1
2.
Overview ....................................................................................................................... 2
3.
Installation .................................................................................................................... 2
3.1 Lens Installation and Adjustment ......................................................................................... 2
3.2 Top / Bottom-Mount ............................................................................................................ 3
4.
Basic Connection ........................................................................................................... 4
5.
OSD Menu Structure ...................................................................................................... 5
6.
Specifications ................................................................................................................ 9
iii
EQ900 eZ.HD True Day/Night Box Camera
1. Introduction
The EQ900 is a box camera equipped with 1/2.8" SONY 1.37M pixels CMOS to deliver 720p high
Resolution. The camera delivers vastly superior video quality compared to traditional CCTV images.
This superior resolution not only captures more critical evidentiary information, but the inherent
ability for video also extends the area of coverage, expedites completion of investigations, resolves
complaints and reduces both capital and operational costs.
The EQ900 provides 3D Noise Reduction to improve picture clarity while enabling DVRs to improve
disk storage utilization. Full suite of OSD menu options controlled from the built-in function
buttons. Digital Wide Dynamic Range expansion to deliver properly exposed images despite bright
light sources, deep shadows and/or unbalanced lighting in the same scene. Allows flexible choices
of manual & DC iris control lenses with C / CS mount for outstanding coverage in a wide range of
demanding surveillance environments while delivering stunning image quality. The EQ900
supports both NTSC and PAL scanning systems, which can be switched via OSD.
1.1 Packing List



Camera Body x 1
DC Power Pigtail Cable x 1
User Manual x 1


Hexagon Wrench x 1
C-mount Lens Adapter x 1
1.2 Features

720p with high flexibility and performance for astounding image


1/2.8" SONY 1.37M pixels CMOS with very low light sensitivity
Support C/CS Mount


D-WDR to improve the visibility under high contrast scene
Provides 3D- Noise Reduction ensures less blurry moving subjects, vivid and high SN ratio
images even under low light environments

Support 720p & 960H analog signal output, which can be easily switched by OSD
1
EQ900 eZ.HD True Day/Night Box Camera
2. Overview
No.
Name
Descriptions
1
Dual Video Output
720p and 960H output, using a 75 Ohm BNC-type coaxial cable.
2
OSD Menu
3
Power LED
Glow red then power is present.
4
Grounding Stud
Ensure a good grounding when used.
5
Power Input Terminal
Connect to 12VDC/24VAC power source.
Use the function buttons to configure the settings in the OSD
menu.
3. Installation
3.1 Lens Installation and Adjustment
You can install either a CS-mount or a C-mount lens into the camera. It is recommended to use
a lens with aperture ratio of F/1.2 or lower. Please refer to the following steps.
CS-Mount Lens:
1.
Remove the Cover Cap from the Camera Body.
2.
Install the lens into the Camera Body.
3.
Adjust the lens using the Focus / Zoom Screws.
2
EQ900 eZ.HD True Day/Night Box Camera
C-Mount Lens:
1.
Remove the Cover Cap from the Camera Body.
2.
Install the lens into the Camera Body using the supplied C-Mount Lens Adapter.
3.
Adjust the lens using the Focus / Zoom Screws.
If you are using a DC Auto Iris lens:
1.
Remove the Cover Cap from the Camera Body.
2.
Install the lens into the Camera Body.
3.
Connect the DC Iris Cable to the DC Auto Iris Lens Connector.
Warning: Installing a C-mount lens without the C-mount lens adapter may damage the
camera sensor.
3.2 Top / Bottom-Mount
You can use a mounting bracket and screw it on the top of the Camera Body to suspend the
camera, or on the bottom of the Camera Body to support the camera.
3
EQ900 eZ.HD True Day/Night Box Camera
4. Basic Connection
1.
2.
Connect the camera to a 12VDC or 24VAC power source using the supplied DC Power
Pigtail Cable. The power LED will be lit in red.
Configure the OSD Menu, using the function button.
Note: The function button is not only for direction control, also for switching Video format
and Video output. Please follow the detailed instruction as below:
 Press the "down" button key over 5s to switch video format from PAL to NTSC.
 Press the "left" button key over 5s to switch video output from 720p to 960H
(720p is the default).
 Press the "right" button key over 5s to switch video output from 960H to 720p.
3.
Connect the camera to an AHD DVR or a monitor for setting image aim and focus before
mounting the camera.
4
EQ900 eZ.HD True Day/Night Box Camera
5. OSD Menu Structure
The default value is marked with a star “*”.
No.
Main
Sub Menu
Sub Menu / Function
Indoor*
Min Shu.
Mode
1
Lens
DC*
Outdoor
Max. Shu.
NTSC: 1/30*
PAL: 1/25*
NTSC: 1/60,FLK,1/240,
1/480,1/1000,
1/2000,1/5000*,
1/10000, 1/50000
PAL: 1/50,FLK,1/200,
1/400,1/1000,
1/2000,1/5000*,
1/10000, 1/50000
Iris
Speed
0 – 15(0*)
Manual
Shutter
AGC
Sens-up
2
Exposure
Brightness
NTSC: 1/30, 1/60, FLK, 1/240, 1/480, 1/1000, 1/2000, 1/5000,
1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto*
PAL: 1/25, 1/50, FLK, 1/200, 1/400, 1/1000, 1/2000, 1/5000,
1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto*
0 – 15(15*)
Off*
Auto
Sens-up
X2, X4*, X6, X8, X10, X15, X20, X25, X30
Level
0-8(8*)
Pos/Size
Position, Size,↑,↓,→,←
Gradation
0-2(0*)
1-100(40*)
Off*
D-WDR
On
Auto
Off*
Defog
Auto
Default
Off*
3
Backlight
BLC
Level
Middle*, High, Low
Area
Position, Size,↑,↓,→,←
5
EQ900 eZ.HD True Day/Night Box Camera
Default
Select
Display
HSBLC
Area1*, Area2, Area3, Area4
Off
On*
Position, Size,↑,↓,→,←
Black
Mask
On*/Off
Level
0-100(20*)
Model
All Day*
Night
AGC Level
0-255(48*)
Default
ATW*
AWC→SET
4
White
Balance
Indoor
Outdoor
Manual
Blue
1-500(50*)
Red
0-100(50*)
D→N(Delay)
0-60(1*)
N→D(Delay)
0-60(1*)
D→N(AGC)
1-255(240*)
D→N(Delay)
0-60(1*)
N→D(AGC)
1-255(50*)
N→D(Delay)
0-60(5*)
AWB
Ext
Auto*
5
Day &
Night
Color
Burst
Off*/On
Off*
B/W
IR Smart
IR PWM
6
NR
On
Level
0-15(4*)
Area
Position, Size,↑,↓,→,←
Off
0-100(100*)
2DNR
Middle*/Low/Off/High
3DNR
Middle*/Low/Off/High
Off*
Cam Title
7
Special
D-effect
On
0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ▶→←
↑↓()ˉ-_▊/=&:~,.
Freeze
Off*/On
Mirror
Off*, Mirror, V-flip, Rotate
6
EQ900 eZ.HD True Day/Night Box Camera
Neg.
Image
Off*/On
Off*
Select
Display
Motion
On
Area1*,Area2,Area3,Area4
On*
Position, Size,↑,↓,→,←
Off
Sensitivity
0-100(64*)
Color
Green*, Blue, White, Red
Trans
Alarm
1.00*,0.75,0.50,
0.25
View Type
Off, Block, Outline, All*
OSD View
On*/Off
Alarm Out
On*/Off
Alarm Sig
High*, Low
Time
1-15(3*)
Default
Off
Select
Area1*,Area2,Area3,Area4
Off
Display
Privacy
On
Color*
Position, Size,↑,↓,→,←
Mosaic
Position, Size,↑,↓,→,←
Inv
Position, Size,↑,↓,→,←
Color
White*, Black, Red, Blue, CYAN, Yellow,
Green
Trans
1.00*,0.75,0.50,
0.25
Default
Language
ENG*/CHN1/CHN2/GER/FRA/ITA/SPA/POL/RUS/POR/NED/TUR
Off
Live DPC
On*
AGC level
0-255(65*)
Level
0-100(100*)
Pos/Size
Position, Size,↑,↓,→,←
Start
Close the iris then press
DPC View
Off*/On
Level
0-60(5*)
AGC
0-14(14*)
Off
Defect
White
DPC
On*
7
EQ900 eZ.HD True Day/Night Box Camera
Sens-up
x2*, x4, x6, x8,x10, x15,
x20, x25, x30
Pos/Siz
Position, Size,↑,↓,→,←
Start
Press Enter
DPC View
Off*/On
Level
0-255(255*)
Off*
Black
DPC
RS485
On
CAM ID
0-255(1*)
ID Display
Off*/On
Baud Rate
2400,4800,9600,19200 ,38400
Off
Sharpness
Auto*
CRT
8
Adjust
Level
0-10(6*)
Start AGC
0-255(50*)
End AGC
0-255(200*)
Black Level
0-60(0*)
Blue Gain
0-100(50*)
Red Gain
0-255(50*)
User*,0.45,0.50,0.55,0.60,0.65,0.70,0.75,
CRT/LCD
Gamma
0.80,0.85,0.90,
0.95,1.00
Blue Gain
0-100(50*)
Red Gain
0-100(50*)
LCD*
LSC
Off*/On
Video. Out PAL/NTSC
9
Exit
Save& END /Reset/Not Saved
8
EQ900 eZ.HD True Day/Night Box Camera
6. Specifications
P/N
Pickup Device
Video Format
Effective Pixels
Scanning System
Sensitivity
S/N Ratio
Electronic Shutter
Video Output
Gamma Correction
Lens Type
BLC
AGC
White Balance
Sync Mode
Day/Night
IR LED
IR Distance
OSD Languages
DNR
DEFOG
D-WDR
Sens-up
Mirror
Motion Detection
Privacy Mask
Environmental
Power Source
Operating
Temperature
Humidity
Dimensions
Weight
Certifications
EQ900
1/2.8" SONY 1.37M pixels CMOS
NTSC and PAL( can be switched via OSD)
1280 (H)*720 (V)
Progressive Scan
0.08 lux.
Over 48 dB (AGC OFF)
AUTO, Manual (X30~1/ 50000), FLK
BNC 1.0Vp-p 75Ω
0.45
C/CS Mount (lens sold separately)
OFF/BLC/HS BLC Selectable
0~15 Levels
ATW/AWC-SET/INDOOR/OUTDOOR/MANUAL/AWB
Internal
Ext, Auto, Color, B/W
30 Units
Up to 30m/100ft. (depending on scene IR reflectivity)
12-Language
2DNR/3DNR, Off
Off/Auto(under B/W mode)
On/Off
Off/On(x30~x2)
Off, Mirror, V-flip, Rotate
On/Off for 4 selectable zones
On/Off for 4 selectable zones
IP66 Weather Resistant
12VDC/24VAC
-10°C~50°C / 14°F~122°F
20%~80%
129 x 58 x 55mm /5.08” x 2.28" x 2.17"
240g/0.53lbs
CE/FCC/ RoHS
Specifications and designs are subject to change for improving the functionality of this product
without notice.
9
EverFocus Electronics Corp.
EverFocus Taiwan:
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Taipei City, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 3943
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: +49 2822 93940
FAX: +49 2822 939495
www.everfocus.de
info@everfocus.de
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 10 6297 1423
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838
www.everfocus.com
sales@everfocus.com
EverFocus USA - New York:
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA
TEL: +1 631 436 5070
FAX: +1 631 436 5027
www.everfocus.com
sales@everfocus.com
EverFocus Japan:
3F Kuramochi, Buildingll 2-2-3 Koto-Bashi,
Sumida-Ku Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189
www.everfocus.co.jp
info@everfocus.co.jp
EverFocus China - Shanghai:
Room 403, Ruijin Business Center, No.96, Zhaojiabang
Road, Luwan district, Shanghai 200020, China
TEL: +86 21 6471 2229 / 6471 2291
FAX: +86 21 6471 0566
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus India:
UBS, 629/1243, 1st Floor, G Block, Behind
Teacher’s Colony, Bandra Kurla Complex,
Bandra (E), Mumbai 400 051, India
TEL: +91 22 6726 4500
FAX: +91 22 6726 4518
www.everfocus.in
sales@everfocus.in
Your EverFocus product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from
your household waste.
Please, dispose of this equipment at your
local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit
qualitativ hochwertigen Materialien
und Komponenten, die recycelt und
wieder verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling
Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!