IPPC-7157 Series
15" XGA TFT LCD Pentium 4/
Celeron D Industrial Panel PC
with 7 x PCI/PCIe Slots and
Membrane Keypad
User Manual
Copyright Notice
This document is copyrighted 2008, by Advantech Co. Ltd. All rights are
reserved. Advantech Co., Ltd. reserves the right to alter the products
described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of Advantech. Information provided in this manual is intended to be accurate and reliable.
However, Advantech assumes no responsibility for use of this manual,
nor for any infringements upon the rights of third parties which may
result from such use. All brand and product names mentioned herein are
trademarks or registered trademarks of their respective holders.
Acknowledgments
IBM and PC are trademarks of International Business Machines Corporation.
For more information on this and other Advantech products, please visit
our website at:
http://www.advantech.com
For technical support and service, please visit our support website at:
http://www.advantech.com.tw/support/
Part No. 2003715700
2nd Edition
Printed in Taiwan
April 2008
IPPC-7157 User Manual
ii
FCC Class A
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Warning!
Any changes or modifications made to the
equipment which are not expressly approved by
the relevant standards authority could void your
authority to operate the equipment.
iii
Packing List
Before setting up the system, check that the item is among those listed
below and is in good condition. If your Workstation does not match any
of those below, please contact your dealer immediately.
• 1 x IPPC-7157 Workstation
• 1 x Accessory Box, with:
• CD ROM for IPPC-7157 Series DRV
• CD ROM for AIMB Motherboard
• Registration and 2 year Warranty card
• Startup manual of AIMB-762 mother board
• SATA Cable x 2
• SATA Power Cable x 2
• PATA 40PIN DMA66 Flat Cable
• FDD Cable
• D-Sub Flat Cable with bracket
• Mother Board I/O sheet metal bracket
• Jumper Bag (mini jumper*20)
IPPC-7157 Industrial Workstations includes the following models:
IPPC-7157A-X1AE: Rugged Pentium® D/Pentium® 4/Celeron® D
Industrial workstation with 15” LCD, AIMB-762 M/B, 300W AC power
supply. Stainless steel chassis and aluminum front panel with membrane
function keys.
IPPC-7157A-R1AE : IPPC-7157A-X1AE with resistive touchscreen
IPPC-7157 User Manual
iv
Additional Information and Assistance
Step 1. Visit the Advantech web site at www.advantech.com where you
can find the latest information about the product.
Step 2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional
assistance. Please have the following information ready before
you call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, application
software, etc.)
• A complete description of the problem
• The exact wording of any error messages
v
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according
to the user's manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE
THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR
ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE
EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT
TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED
BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained
herein.
IPPC-7157 User Manual
vi
Contents
Chapter
Chapter
1 General Information ....................................... 2
1.1
1.2
Introduction ....................................................................... 2
Specifications .................................................................... 3
1.3
Dimensions........................................................................ 5
1.2.1
1.2.2
1.2.3
1.2.4
1.2.5
2 System Setup.................................................... 8
2.1
A Quick Tour of IPPC-7157 ............................................. 8
2.1.1
2.1.3
2.1.4
2.1.5
2.1.6
2.1.7
Chapter
Figure 2.1:Open View .................................................... 9
Figure 2.2:Side View ..................................................... 9
PS/2 Mouse and Keyboard .......................................... 10
Serial COM Ports ......................................................... 11
USB Ports .................................................................... 11
Figure 2.3:Opening the Front USB Port Cover ........... 11
Audio Interface ............................................................ 12
Ethernet ........................................................................ 12
Adjusting the LCD Brightness ..................................... 12
2.2
Installing a CPU & CPU Cooler ..................................... 13
2.3
2.4
Installing Optional Disk Drives....................................... 14
Rack Mounting................................................................ 14
Figure 2.4: Installing the CPU Cooler ......................... 13
3 Touchscreen ................................................... 16
3.1
3.2
Chapter
General ........................................................................... 3
System Hardware ........................................................... 3
LCD Display .................................................................. 4
Touchscreen (Optional) ................................................. 4
Environment ................................................................... 5
Introduction ..................................................................... 16
Touchscreen Driver Installation & Configuration .......... 16
4 Award BIOS Setup........................................ 18
4.1
4.2
Award BIOS Setup.......................................................... 18
CMOS Setup Utility ........................................................ 18
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
Advanced BIOS Features ................................................ 22
Advanced Chipset Features............................................. 26
Integrated Peripherals...................................................... 30
Power Management Setup............................................... 34
PnP/PCI Configuration.................................................... 38
PC Health Status.............................................................. 40
Frequency/Voltage Control ............................................. 41
Load Optimized Defaults ................................................ 42
Set Password ................................................................... 42
4.2.1
Standard CMOS Setup ................................................. 19
Figure 4.1:Standard CMOS features ............................ 19
Figure 4.2:Standard CMOS features ............................ 20
vii
4.12
4.13
Save & Exit Setup ........................................................... 43
Exit Without Saving ........................................................ 43
Appendix A LCD Specifications........................................ 46
A.1
IPPC-7157 LCD Specifications ...................................... 46
Appendix B Pin Assignments ............................................ 48
B.1
ATX Power Connector 1 (CN1) .................................... 48
B.2
ATX Power Connector 2 (CN2)...................................... 49
B.3
LVDS Connector 1(CN4)................................................ 49
B.4
LVDS Connector 2 (CN6)............................................... 50
B.5
Inverter Power Connector (CN5) .................................... 50
B.6
FDD Connector (CN9) .................................................... 51
B.7
Internal Speaker Connector (CN15)................................ 52
B.8
IR Connector (CN24) ...................................................... 52
B.9
B.10
Fan Power Connector (FAN1 & FAN2) ......................... 52
COM1 RS-232 serial port (CN10) .................................. 53
B.11
COM2 (CN11)................................................................. 53
Table B.1:AT Power connector 1 (CN1) ...................... 48
Table B.2:ATX power connector 2 (CN2) ................... 49
Table B.3:LVDS connector 1(CN4) ............................. 49
Table B.4:Table B.4: LVDS connector 2 (CN6) .......... 50
Table B.5:Inverter power connector (CN5).................. 50
Table B.6:FDD connector (CN9).................................. 51
Table B.7:Internal speaker connector (CN15).............. 52
Table B.8:IR connector (CN24).................................... 52
Table B.10:COM1 RS-232 serial port (CN10)............. 53
Table B.11:COM2 (CN11) ........................................... 53
Appendix C Keyboard Translator .................................... 56
C.1
C.2
Overview ......................................................................... 56
Programming the Front Panel Macro Keys..................... 57
IPPC-7157 User Manual
viii
CHAPTER
1
General Information
This chapter gives background
information on the IPPC-7157 series
Sections include:
• Introduction
• Specifications
• Dimensions
Chapter 1 General Information
1.1 Introduction
The IPPC-7157 is an all new designed workstation with 15" TFT LCD
and 7 expansion slots. With the new ID Design, IPPC-7157 will be a
brand new front panel workstation from existed AWS series.The IPPC7157 support ATX industrial mother board and standard motherboard.
The IPPC-7157 also provides many powerful features such as detachable
front panel module, a front-access USB port, 53 membrane key & touch
pad with two mouse buttons, 6 OSD Control keys, NEMA4/IP65 compliant front panel, Optional analog resistive touchscreen (USB Interface).
Modularized Side-Open Front Panel Makes Maintenance Easy
The IPPC-7157 makes user can maintain the system fast and easily. First,
if there are problems with the LCD display, the detachable front panel
with “ hi nge” design allows you to replace it or service it simply and
quickly. This helps saves downtime costs associated with system crashes.
Second, the side-open LCD front panel also make it more convenient
when you want to maintain the CPU, I/O cards, HDD, CD-ROM and
even floppy.
Industrial Design Withstands Harsh Environments
In addition, the AWS-8259 also features many powerful functions tomeet
the industrial-grade requirements. The front panel is made of Aluminum
and being chemical treated by anode. That prevents the panelfrom damaging by acid and salt. Besides, it's waterproof and IP65/NEMA4 compliant. The AWS-8259 also offers the stainless steel chassis. It also protects
the chassis. For keeping the system working properly, the AWS-8259 provides a fan & filter to avoid overheating & dust. In addition, the AWS8259 also provides three mounting ways to fit different application: 19"
rack, panel or wall mounting.
IPPC-7157 User Manual
2
1.2 Specifications
1.2.1 General
• Button Control:
Membrane Keypad 1: 43 operating keys
Membrane Keypad 2: 10 programmable macro function keys
• BIOS: Award™ 8 Mbit FWH
• Certifications: BSMI, CCC, CE, FCC
• Cooling System: 1 x 49 CFM fan w/50,000 hrs MTBF
• Dimensions (W x H x D):
482 x 354.8 x 162 mm (18.97" x 13.96" x 6.37")
• Disk Drive Bay:
Supports 1 x FDD, 2 x 3.5" HDD & 1 x CD-ROM (HDD optional)
• Enclosure: Front Panel – Aluminum,
Chassis – Anti-rust
• Mounting: Panel, 19” Rack
• Power Input: 90 ~ 264 VAC @ 47 ~ 63 Hz full range 6.0/3.0A
• Power Ouput: + 5V@30A, +12V@15A, +3.3V@28A, -5V@0.3A,
-12V@0.8A, +5 VSB@2A
• Power Supply: Watt :300 W, MTBF: 100,000 hrs
• Weight (Gross): 18 kg ( 39.7 lb)
1.2.2 System Hardware
• Audio Ports: 1 x Mic-in, 1 x Line-out
• Chipset: Intel 945G + ICH7R
• CPU: Socket 775, Intel Pentium 4 2.8GHz
Intel Celeron M 2.5GHz
• Expansion Slots: 1 x PCIe x16 4.0 GB/s per direction
1 x PCIe x4 1.0 GB/s per direction
5 x PCI 32-bit/33 MHz
• Keyboard/Mouse: 2 x PS/2 for mouse & keyboard interface
• LAN:
2 x 10/100/1000Base-T
3
Chapter 1
• Memory: 4 x 240-pin Dual ch DDR2 DIMM sockets
(Up to 4 GB, Clock 266)
• Parallel Port:
1 x enhanced parallel port
Supports SPP/EPP/ECP parallel mode.
BIOS configurable to LPT1, LPT2, LPT3 or disabled
• Serial Ports:
1 x RS-232/422/485 on pin header
1 x RS-232 on rear I/O
• USB Ports:
1 x USB 2.0 on front panel
4 x USB 2.0 on rear I/O
1.2.3 LCD Display
• Backlight Life: 60,000 hrs
• Contrast Ratio: 500 : 1
• Display Size: 15"
• Display Type: XGA TFT LCD
• Luminance: 250 cd/m2
• Max. Colors: 16.2 M (RGB 6-bit + FRC data)
• Max. Resolution: 1024x768
• OSD Control: ON/OFF, Brightness down, up (behind the front panel)
• Viewing Angle (H/V°): 140/120
1.2.4 Touchscreen (Optional)
• Interface: USB
• Lifespan:
10 million with silicone rubber of R8 finger, writing rate is 250g at 2X/s
• Light Transmission: > 80% (AMT)
• OS Support: Windows 95/98/ME/2000/XP/CE/NT/Vista, Linux
• Type: 8W Resistive
IPPC-7157 User Manual
4
1.2.5 Environment
• Humidity: 5 ~ 85% RH @ 40° C (non-condensing)
• Ingress Protection: Front panel NEMA4/IP65
• Operating Temperature: 0 ~ 50° C (32 ~ 122° F)
• Storage Temperature:
-20 ~ 60° C (-4 ~ 140° F)
• Vibration Protection: 5~500 Hz,
1 GRMS random vibration (operating)
1.3 Dimensions
IPPC-7157A
17
M2
M3
7
8
4
5
1
2
+
0
9
__
___
M1
”
/
6
3
_
=
M4
Esc
M5
Delete
PgUp
Shift
Space
Tab
PgDn
Back
Space
M6
Ctrl
M7
Enter
Alt
Left
M8
Right
M9
M10
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Figure 1.1: IPPC-7157 Dimensions
5
Chapter 1
IPPC-7157 User Manual
6
CHAPTER
2
System Setup
This chapter details system setup for
the IPPC-7157 Series.
Sections include:
• A Quick Tour of IPPC-7157
• Installing a CPU & CPU Cooler
• Installing Optional Disk Drives
• Rack Mounting
Chapter 2 System Setup
2.1 A Quick Tour of IPPC-7157
Before you start the computer, please follow these procedures to set up
the system.
1. Check and adjust jumpers on the motherboard (see Chapter 3)
2. Install SDRAM
3. Install CPU & CPU Cooler
4. Install add-on cards
5. Connect the wires, cables and accessories
6. Mount the computer
7. Program the BIOS settings
8. Install an operating system.
Warnings
1. Switch off and unplug the computer every time
you access its interior.
2. The motherboard inside the system is composed
of many delicate ICs, chips and other integrated
circuit components. These components are easily
damaged by static shock. When you begin to install
components, please:
- Avoid touching metal parts of the motherboard.
- Wear an anti-static ring when handling a CPU or
SDRAM module.
- Put SDRAM modules and the CPU inside an
anti-static bag or a similar place before
installation.
IPPC-7157 User Manual
8
Figure 2.1: Open View
Figure 2.2: Side View
9
Chapter 2
2.1.1 PS/2 Mouse and Keyboard
If you wish to use a full-size desktop keyboard and PS/2 mouse with your
Workstation, follow these instructions:
1.
Be sure the workstation is turned off.
2.
Reattach the original 2 black PS/2 keyboard & mouse cables if they
are already connected on the right side of the chassis.
3.
Attach your keyboard & mouse adapter onto the PS/2 ports.
Note:
Please be aware, once after connecting your keyboard
& mouse onto the I/O of 7157 right side of chassis, the
all front panel function keys & touch pad will be disabled, since the original cables are removed
2.1.2 Parallel Ports
The Workstation supports the latest EPP and ECP parallel port protocols
for improved performance and versatility with compatible printers or
other devices.
To connect the Workstation to a printer or other devices:
1.
Make sure both the Workstation and the printer/devices are turned
off.
2.
Connect the 25-pin male connector of the printer cable to the 25pin female port on the Workstation labelled "parallel port."
3.
If necessary, attach the other end of your printer cable to your
printer, and fasten any retaining screws.
4.
Turn on the printer and any other peripheral devices you may have
connected to the Workstation. Then turn on the Workstation.
5.
If necessary, run the Workstation's BIOS setup program to configure the parallel port to respond as required by your printer and software operating environment.
IPPC-7157 User Manual
10
2.1.3 Serial COM Ports
There are two serial COM ports on the I/O at the right side of workstation. You can easily attach a serial device to the Workstation, such as an
external modem or mouse. Follow these instructions:
1.
Make sure the Workstation and any other peripherial devices you
may have connected to the Workstation are turned off.
2.
Attach the interface cable of the serial device to the Workstation's
serial port. (See Fig. 2-2.) If necessary, attach the other end of the
interface cable to your serial device. Fasten any retaining screws.
3.
Turn on any other peripheral devices you may have connected to
the Workstation, and then turn on the Workstation.
4.
Refer to the manual(s) which accompanied your serial device(s) for
instructions on configuring your operating environment to recognize the device(s).
5.
Run the BIOS setup program to set the I/O address and IRQ, and
configure the jumper settings to change the mode of the COM ports
(refer to section 3.3).
2.1.4 USB Ports
An external USB device may be connected to the system via the USB
ports located on the right side of the system unit and also could access
from 1 USB port on the front panel of IPPC-7157.
1.
Connect the external device to the system.
2.
The USB ports support hot plug-in connection. You should install
the device driver before you use the device.
Figure 2.3: Opening the Front USB Port Cover
11
Chapter 2
2.1.5 Audio Interface
The audio interface includes three jacks: microphone-in, line-out and
line-in. Their functions are:
Microphone-in: Use an external microphone to record voice and sound.
Line-out: Output audio to external devices such as speakers or earphones. The built-in speaker will not be disabled when the line-out jack is
connected to external audio devices.
1.
Connect the audio device to the system.
2.
Install the driver before you use the device.
2.1.6 Ethernet
To install Ethernet for your system:
1. Connect the Ethernet cable.
2. Turn on the Workstation.
3. Run the Ethernet driver in the Mother Board Disc to connect up to the
program: "E:\Drv_LAN\Intel 82573\Autorun.exe"
2.1.7 Adjusting the LCD Brightness
The LCD OSD control key is located behind the front panel module, you
have to open the front panel to access it.
1.
Unscrew the 2 screws on the right side of front panel.
2.
Open the front panel door, to find the LCD OSD control key.
IPPC-7157 User Manual
12
2.1.8 System On/Off
The IPPC-7157 has 1 system on/off switch, located inside the chassis.
2.2 Installing a CPU & CPU Cooler
The CPU can be upgraded to improve system performance. The 7157
provides Socket 478 architecture which supports Pentium 4 CPU up to
2.8 GHz, and Celeron up to 2.5 GHz.
While installing or upgrading the CPU, CPU cooler must be correctly
removed. After installing CPU, then the CPU cooler can be screwed back
into the standoff from the chassis. See below for reference.
Figure 2.4: Installing the CPU Cooler
13
Chapter 2
2.3 Installing Optional Disk Drives
The IPPC-7157 provides spaces for two 3.5" hard disk drives, one CDROM drive, & one 3.5" floppy disk drive within the chassis. Front-facing
FDD & CD-ROM have already been installed. You can access them after
opening the front LCD panel.
Below is the procedure of installing HDD:
1.
Unscrew and remove the HDD Drive Bay.
2.
Unscrew the 4 screws on the drive bay, and separate the 2 parts.
3.
Install HDD with 2 screws on each side.
4.
Combine the 2 sheet metal parts of the drive bay with the screws
5.
Install the HDD drive bay back into chassis.
2.4 Rack Mounting
The IPPC-7157A can be mounted to a 19" industrial rack.
IPPC-7157 User Manual
14
CHAPTER
2
3
Touchscreen
This chapter contains information on
the touchscreen, its installation and
configuration.
Sections include:
• Introduction
• Installing Windows 2000/X Drivers
• Configuring PenMount Drivers
• Uninstalling PenMount Drivers
Chapter 3 Touchscreen
3.1 Introduction
The IPPC-7157 Series’ optional touchscreen uses advanced 8-wire resistive technology. It provides more accurate sensing capacity than other
technologies. The touchscreen is specially designed for tough industrial
environments, and has been approved to FCC Class B standards.
3.2 Touchscreen Driver Installation & Configuration
The touchscreen of IPPC-7157 is controlled by USB interface and has
drivers for Linux, Windows 2000, Windows XP, Windows Vista and Windows CE. You should read the instructions in this chapter carefully before
you attempt installation.
For driver installation, please insert the IPPC support CD and refer to the
path below: "D:\System Drivers\IPPC-7157A\Touch Screen Driver\DMC
6000 (Combo)\Manual\PenMount Win2K&XP&2003&Vista Universal
Driver Manual V1.02.pdf"
IPPC-7157 User Manual
16
CHAPTER
4
Award BIOS Setup
This chapter details the Award BIOS Setup.
Sections include:
• Award BIOS Setup
• CMOS Setup Utility
• Advanced BIOS Features
• Advanced Chipset Features
• Integrated Peripherals
• Power Management Setup
• PnP/PCI Configuration
• PC Health Status
• Frequency/Voltage Control
• Load Optimized Defaults
• Set Password
• Save & Exit Setup
• Exit Without Saving
Chapter 4 Award BIOS Setup
4.1 Award BIOS Setup
The IPPC-7157 comes with an Award BIOS chip that contains the ROM
setup for your system. This chip serves as an interface between the processor and the rest of the mainboard's components. This chapter explains
the information contained in the setup program and tells you how to modify the settings according to your system configuration. Some setup items
will not be explained, because it is recommended that users do not change
such items.
Note:
Values for the various setup items that appear on
your own screen (including default values) may
not be the same as the values shown on the
screen figures in this chapter. This is because
the BIOS is revised and updated from time to
time. If in doubt, check Advantech's website for
the latest BIOS versions and related information.
4.2 CMOS Setup Utility
A setup program, built into the system BIOS, is stored in the CMOS
RAM that allows the configuration settings to be changed. This program
is executed when the user changes the system configuration; when the
user changes the system backup battery; or when the system detects a
configuration error and asks the user to run the setup program. At poweron RAM testing, the message "Press DEL to enter Setup" appears. After
pressing the "DEL" key, the CMOS setup utility screen will appear as
shown in followings. Use the arrow keys to select and press "Enter" to
run the selected program.
IPPC-7157 User Manual
18
Frequency/Voltage Control
Load Optimized Defaults
Set Password
Save & Exit Setup
Exit without Saving
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
Esc : Quit
F10 : Save & Exit Setup
↑↓→← : Select Item
Time, Date, hard disk Type…
4.2.1 Standard CMOS Setup
Standard CMOS Setup records some basic system hardware configuration and sets the system clock and error handling. You only need to modify the configuration values of this option if you want to change your
system hardware configuration or when the data stored in the CMOS
memory gets lost or damaged.
Run the STANDARD CMOS SETUP as follows:
1.
Choose “STANDARD CMOS SETUP” from the Main Menu and a
screen with a list of options will appear:
Date (mm:dd:yy)
Time (hh:mm:ss)
Mon, January 1 2001
12 : 05 : 55
IDE
IDE
IDE
IDE
None
None
None
None
Primary Master
Primary Slave
Secondary Master
Secondary Slave
Drive A
Drive B
1.44M, 3.5 in.
None
Video
Halt On
Select Display Device
TV Type
EGA/VGA
All Errors
Auto
NTSC
Base Memory
Extended Memory
Total Memory
640K
31744K
32768K
Item Help
Menu Level
Figure 4.1: Standard CMOS features
2.
Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.
19
Chapter 4
Date (mm:dd:yy)
The BIOS determines the day of the week from the other date information. This field is for information only. Press the left or right arrow key to
move to the desired field (date, month, year). Press the PgUp or PgDn key
to increment the setting, or type the desired value into the field.
Time (hh:mm:ss)
The time format is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Press the left or right arrow key to move to
desired field. Press the PgUp or PgDn key to increment the setting, or
type the desired value into the field.
Primary / Secondary & Master / Slave
This field records the specifications for all non-SCSI hard disk drives
installed in your system. Refer to the respective documentation on how to
install the drives.
IDE HDD Auto-Detection
Press Enter
Item Help
Menu Level
IDE Primary Master
Access mode
Auto
Auto
Capacity
13022 MB
Cylinder
Head
Percomp
Landing Zone
Sector
25232
16
0
25231
63
Figure 4.2: Standard CMOS features
Drive A / Drive B
Select this field to the type(s) of floppy disk drive(s) installed in your system. The choices are:
360 KB, 5.25 in;
1.2 MB, 5.25 in;
720 KB, 3.5 in;
1.44 MB, 3.5 in;
2.88 MB, 3.5 in;
None.
IPPC-7157 User Manual
20
Video
Select the type of primary video subsystem in your computer. The BIOS
usually detects the correct video type automatically. The BIOS supports a
secondary video subsystem, but you do not select it in setup.
Halt On
During the power-on self-test (POST), the computer stops if the BIOS
detects a hardware error. You can tell the BIOS to ignore certain errors
during POST and continue the boot-up process.
Select Display Device
Select this field to the display device. The choices are:
Auto
CRT
LCD
CRT+LCD
TV
CRT+TV
TV Type
Select this field to the type of TV. The choices are:
NTSC
PAL
Base Memory
Typically 640KB. Also called conventional memory. The DOS operating
system and conventional applications use this area.
Extended Memory
Above the 1MB boundary. Early IBM personal computers could not use
memory above 1MB, but current PCs and their software can use extended
memory.
21
Chapter 4
Total Memory
This option shows system memory capacity.
3.
Press <ESC> to return to the Main Menu when you finish setting
up all items.
4.3 Advanced BIOS Features
Advanced BIOS Features improves your system performance or sets up
system features according to your preference.
Run the ADVANCED BIOS FEATURES as follows:
1.
Choose“Advanced BIOS Features”from the Main Menu and a
screen with a list of options will appear.
2.
Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.
Virus Warning
CPU Internal Cache
External Cache
CPU L2 Cache ECC Checking
Processor Number Feature
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
PS/2 Mouse Function
OS Select For DRAM > 64MB
Reports No FDD For Win95
Video BIOS Shadow
C8000-CBFFF Shadow
CC000-CFFFF Shadow
D0000-D3FFF Shadow
D4000-D7FFF Shadow
D8000-DBFFF Shadow
DC000-DFFFF Shadow
Small Logo (EPA) Show
IPPC-7157 User Manual
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Floppy
HDD-0
CDROM
Enabled
Disabled
Enabled
On
Fast
Disabled
6
250
Setup
Non-OS2
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
22
Item Help
Menu Level
Virus Warning
When enabled, you receive a warning message if a program (specifically,
a virus) attempts to write to the boot sector or the partition table of the
hard disk drive.
You should then run an antivirus program. Keep in mind that this feature
protects only the boot sector, not the entire hard drive.
Note:
Many disk diagnostic programs that access the boot
sector table can trigger the virus warning message. If
you plan to run such a program, we recommend that
you disable the virus warning.
CPU Internal Cache/External Cache
Cache memory is additional memory that is much faster than conventional DRAM (system memory). CPUs from 486-type up contain internal
cache memory, and most, but not all, modern PCs have additional (external) cache memory. When the CPU requests data, the system transfers the
requested data from the main DRAM into cache memory, for faster
access by the CPU.
CPU L2 Cache ECC Checking
When you select Enabled, it will speed up memory checking when the
external cache contains ECC SRAMs. The choices: Enabled; Disabled.
Processor Number Feature
Choose Disabled or Enabled. When enabled, the processor serial number
will display during the boot up screen.
Quick Power On Self Test
Select Enabled to reduce the amount of time required to run the power-on
self-test (POST). A quick POST skips certain steps. We recommend that
you normally enable quick POST.
23
Chapter 4
First/Second/Third/Other Boot Device
The BIOS attempts to load the operating system from the devices in the
sequence selected in these items. The choices: Floppy; LS/ZIP; HDD;
SCSI; CDROM; Disabled.
Swap Floppy Drive
When enabled, floppy drives A and B will be exchanging without any
physical connection and modification on the cables.
Boot Up Floppy Seek
When enabled, the BIOS tests (seeks) floppy drives to determine whether
they have 40 or 80 tracks. Only 360-KB floppy drives have 40 tracks;
drives with 270KB, 1.2MB, and 1.44MB capacity all have 80 tracks.
Because very few modern PCs have 40-track floppy drives, we recommend that you set this field to disabled to save time.
Boot Up NumLock Status
Toggle between On or Off to control the state of the NumLock key when
the system boots. If On, the numeric keypad is in numeric mode. If off,
the numeric keypad is in cursor control mode.
Gate A20 Option
Gate A20 refers to the way the system addresses memory above 1 MB
(extended memory). When set to Fast, the system chipset controls Gate
A20. When set to Normal, a pin in the keyboard controller controls Gate
A20. Setting Gate A20 to Fast improves system speed, particularly with
OS/2 and Windows.
Typematic Rate Setting
When Disabled, the following two items (Typematic Rate and Typematic
Delay) are irrelevant. Keystroke repeats at a rate determined by the keyboard controller in your system. When Enabled, you can select a typematic rate and typematic delay.
IPPC-7157 User Manual
24
Typematic Rate (Chars / Sec)
When the typematic rate setting is enabled, you can select a typematic
rate (the rate at which character repeats when you hold down a key) of 6,
8, 10, 12, 15, 20, 24, or 30 characters per second.
Typematic Delay (Msec)
Choices: 250; 500; 750; 1000. This option sets the time interval for displaying the first and the second characters. If enabled, the time interval is
optional.
Security Option
If you have set a password, select whether the password is required every
time the System boots, or only when you enter setup. The choices: system; setup.
PS/2 Mouse Function
Disabled: Prevents any installed PS/2 mouse from functioning but free up
occupied IRQ.
Enabled: Allows the operating system to determine whether to enable or
disable the mouse.
OS Select For DRAM > 64MB
Select OS2 only if you are running OS/2 operating system with greater
than 64MB of RAM on your system.
Reports No FDD For Win95
Video BIOS Shadow
Performance will be improved by copying Video BIOS to Shadow RAM.
C8000-CBFFF to DC000-DFFFF Shadow
These options are used to shadow other expansion card ROMs.
Small Logo (EPA) show
3.
Press <ESC> to return to the Main Menu when you finish setting
up all items.
25
Chapter 4
4.4 Advanced Chipset Features
Advanced Chipset Features is used to modify the values of chipset buffers. These buffers control the system options.
Run the Advanced Chipset Features as follows:
1. Choose “Advanced Chipset Features” from the Main Menu and a list of
options will appear.
D R A M Tim i ng b y S P D
D R A M C lo c k
S D R A M C yc le L e ng t h
B a nk In te r le a ve
M e m o r y H o le
P 2 C /C 2P C o nc ur re nc y
S ys te m B IO S C a c he a b le
V id e o R A M C a c he a b le
F ra m e B uf fe r S ize
A G P A p e rtu re S ize
A P G -4 X M o d e
A G P D riving C o ntro l
A G P D riving Va lue
B o o t D e vic e S e le c t
O nC hip U S B
U S B K e yb o a rd S up p o rt
O nC hip S o u nd
C P U to P C I W rite B uf fe r
P C I D y na m ic B u rs ti ng
P C I M a s te r 0 W S W rite
P C I D e la y Tra ns a c tio n
P C I# 2 A c c e s s # 1 R e t r y
A G P M a s te r 1 W S W rite
A G P M a s te r 1 W S R e a d
E na b le d
Host C LK
3
D is a b le d
E na b le d
E na b le d
E na b le d
E na b le d
16M
64M
E na b le d
A uto
DA
B o th
E na b le d
D is a b le d
E na b le d
E na b le d
E na b le d
E na b le d
E na b le d
D is a b le d
D is a b le d
D is a b le d
Ite m H e lp
M e n u L e ve l
Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.
DRAM Timing by SPD
When this item is Enabled, DRAM Timing is set by SPD. SPD (Serial
Presence Detect) is located on the memory modules, BIOS reads information coded in SPD during system boot up.
DRAM Clock
This item allows you to control the DRAM speed.
The choices are : Host Clock, HCLK+33M.
IPPC-7157 User Manual
26
SDRAM Cycle Length
Select CAS latency time in HCLKs of 2 or 3. The system designer
already set the values. Do not change the default value unless you change
specifications of the installed DRAM or the installed CPU.
Bank Interleave
Please use default setting. The choices: Disabled; 2 Bank; 4 Bank.
Memory Hole
In order to improve performance, certain space in memory is reserved for
ISA cards. This memory must be mapped into the memory space below
16 MB. The choices: 15M-16M; Disabled.
P2C/C2P Concurrency
This item allows you to enable/disable the PCI to CPU, CPU to PCI concurrency. The choices: Enabled; Disabled.
System BIOS Cacheable
selecting Enabled allows caching of the system BIOS ROM at F0000hFFFFFh, resulting in better system performance.
Video RAM Cacheable
Selecting Enabled allows caching of the video memory (RAM) at
A0000h to AFFFFh, resulting in better video performance. However,
check your AGP manual to find out if any compatibility problem exists.
Frame Buffer size
This option allows you select memory size shared to on-chip graphics.
AGP Aperture Size
Series of options are available: 4, 8, 16, 32, 64, 128 or 256 MB. Memory
mapped and graphics data structures can reside in a Graphics Aperture.
This area is like a linear buffer. BIOS will automatically report the starting address of this buffer to the O.S. The default setting is 64 MB.
27
Chapter 4
AGP– 4X Mode
This item allows you to enable AGP-4X mode. The choices are: Disabled, Enabled
AGP Driving Control
This item allows you to adjust the AGP driving force. Choose Manual to
key in a AGP Driving Value in the next selection. This field is recommended to set in Auto for avoiding any error in your system. The choice:
Manual, Auto.
AGP Driving Value
This item allows you to adjust the AGP driving force.
The choice: Min=0000 ~ Max=00FF.
Boot Device Select
This item allows you to select your boot display device. The choices are:
Both, Auto
OnChip USB
This should be enabled if our system has a USB installed on the system
board and you wish to use it. Even when so equipped, if you add a higher
performance controller, you will need to disable this feature.
The choices: Enabled; Disabled.
USB Keyboard Support
Enable function when the USB keyboard is being used. When the AT
keyboard is being used, choose disabled. The choices:Enabled; Disabled.
OnChip Sound
Select Enabled to use the on-chip Audio capability of your system. Most
of the following field do not appear when this field is Disabled. For user
who wants to use another sound card, this field must be Disabled.
IPPC-7157 User Manual
28
CPU to PCI Write Buffer
When this field is Enabled, writes from the CPU to the PCI bus are buffered, to compensate for the speed differences between the CPU and the
PCI bus. When Disabled, the writes are not buffered and the CPU must
wait until the write is complete before starting another write cycle.
The choices: Enabled; Disabled.
PCI Dynamic Bursting
When Enabled, every write transaction goes to the write buffer. Bursting
transactions then burst on the PCI bus and non-bursting transactions
don’t. The choices: Enabled; Disabled.
PCI Delay Transaction
Leave this field at default. The choice: Enabled, Disabled.
PCI Master 0 WS Write
When Enabled, writes to the PCI bus are executed with zero wait states.
The choice: Enabled, Disabled.
PCI # 2 Access # 1 Retry
Leave this field at default. The choice: Enabled, Disabled(default).
AGP Master 1 WS Write
Leave this field at default. The choice: Enabled, Disabled(default).
AGP Master 1 WS Read
Leave this field at default. The choice: Enabled, Disabled(default).
Press <ESC> to return to the Main Menu when you finish setting up all
items.
29
Chapter 4
4.5 Integrated Peripherals
Integrated Peripherals option allows you to get some information inside
your system when it is working.
Run the INTEGRATED PERIPHERALS as follows:
1.
Choose“Integrated Peripherals”from the Main Menu and a list of
options will appear.
2.
Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.
On-Chip IDE Channel 0
Enabled
On-Chip IDE Channel 1
Enabled
IDE Prefetch Mode
Enabled
Primary Master PIO
Auto
Primary Slave PIO
Auto
Secondary Master PIO
Auto
Secondary Slave PIO
Auto
Primary Master UDMA
Auto
Primary Slave UDMA
Auto
Secondary Master UDMA
Auto
Secondary Slave UDMA
Auto
Init Display First
PCI Slot
IDE HDD Block Mode
Enabled
Onboard FDD Controller
Enabled
Onboard Serial Port 1
Auto
Onboard Serial Port 2
Auto
UART 2 Mode
Standard
IR Function Duplex
Half
TX, RX inverting enable
No, Yes
Onboard Parallel Port
378/IRQ7
Onboard Parallel Mode
Normal
ECP Mode Use DMA
3
Parallel Port EPP Type
EPP1.9
Onboard Serial Port 3
Serial Port 3 use IRQ
Onboard Serial Port 4
Serial Port 4 Use IRQ
Onboard Legacy Audio
Enabled
Sound Blaster
Disabled
SB I/O B
220H
Add
IPPC-7157 User Manual
30
Item Help
Menu Level
OnChip IDE Channel 0/1
The chipset contains a PCI IDE interface with support from two IDE
channels. Select Enabled to activate the first and/or the second IDE interface. Select Disabled to inactivate an interface if you install a primary
and/or second add-on IDE interface. The choices: Enabled; Disabled.
IDE Prefetch Mode
The on-board IDE drive supports IDE prefetching for faster drive
accesses. If the IDE device doesn’t support prefetching, set this field to
Disabled. The choices: Enabled; Disabled.
Primary Master / Slave PIO & Secondary Master / Slave PIO
Choose Auto or Mode 0~4. The BIOS will detect the HDD mode type
automatically when you choose Auto. You need to set to a lower mode
than Auto when your hard disk becomes unstable.
The choices: Auto; Mode 0; Mode 1; Mode 2; Mode 3; Mode 4.
Primary Master / Slave UDMA & Secondary Master / Slave UDMA
Ultra DMA33/66/100 implementation is possible only if your IDE hard
drive supports it, if the operating environment includes a DMA drive, and
if your system software both support Ultra DMA33/66/100. Select
“Auto” to enable BIOS support. The choices: Auto; Disabled.
Init Display First
Initialize the AGP video display before initializing any other display
device on the system. Thus the AGP display becomes the primary display. The choices: PCI Slot; AGP.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple
sector read/write. If your IDE hard drive supports block mode (most new
drives do), select Enabled for automatic detection of the optimal number
of block read/write per sector the drive can support.
The choices: Enabled; Disabled.
31
Chapter 4
Onboard FDD Controller
Select Enabled if your system has a floppy drive controller (FDC) installing in the system board and you want to use it. If you install add-in FDC
or the system has no floppy drive, select Disabled in this field. The
choices: Enabled; Disabled.
Onboard Serial Port 1 / Port2
Select an address and corresponding interrupt for the first and second
serial ports.
The choices: 3F8/IRQ4; 2E8/IRQ3; 3E8/IRQ4; 2F8/IRQ3; Disabled;
Auto.
UART 2 Mode
The second serial port on your system may offer a variety of infrared port
modes. Click here for a description of various modes. (Click your
browser’s Back button, or your right mouse button, to return to this page.)
The choices: Standard; HPSIR; ASKIR.
IR Function Duplex
This item allows you to select the IR half / full duplex function.
The choices: Half; Full.
TX, RX inverting enable
This item allows you to enable the TX, RX inverting which depends on
different H/W requirement. This field is not recommended to change its
default setting.
The choices: “No, No”; “No, Yes”; “Yes, No”; “Yes, Yes”.
Onboard Parallel Port
Select a logical LPT port name and matching address for the physical parallel (printer) port.
The choices: 378H/IRQ7; 278H/IRQ5; 3BC/IRQ7; Disabled.
IPPC-7157 User Manual
32
Onboard Paralle Mode
Select an operating mode for the onboard parallel (printer) port. Select
Normal, Compatible, or SPP unless you are certain your hardware and
software both support one of the other available modes. The choices:
SPP; EPP; ECP; ECP + EPP.
ECP Mode Use DMA
Select a DMA channel for the parallel port for use during ECP mode.
The choices: 3; 1.
Parallel Port EPP Type
Select EPP port type 1.7 or 1.9. The choices: EPP1.7; 1.9.
Onboard Legacy Audio
This field controls the onboard audio.
• Sound Blaster
• SB I/O Base Address
• SB IRQ Select
• SB DMA Select
• MPU-401
• MPU-401 I/O Address
• Game Port (200-207H)
Press <ESC> to return to the Main Menu when you finish setting up all
items.
33
Chapter 4
4.6 Power Management Setup
POWER MANAGEMENT SETUP allows you to set the system’s power
saving functions.
Run the POWER MANAGEMENT SETUP as follows:
1.
Choose“Integrated Peripherals”from the Main Menu and a list of
options will appear.
2.
Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.
A C P I F u nc tio n
D is a b le d
P o w e r M a na g e m e nt
P M C o nt ro l b y A P M
P re s s E nte r
Ye s
V id e o O ff O p tio n
S us p e nd -- > O ff
V id e o O ff M e t ho d
M O D E M U s e IR Q
V /H S Y N C + B la nk
3
S o ft-O f f b y P W R B T N
W a k e U p E ve nts
Ins ta nd -O f f
P re s s E nte r
Ite m H e lp
M e n u L e ve l
ACPI Function
Select Enabled only if your computer’s operating system supports the
Advanced Configuration and Power Interface (ACPI) specification. Currently, Windows NT 5.0 supports ACPI.
Power Management
When this opinion is chosen, the following item appears for user’s configuration.
P o w e r M a n a g e m e n t
H D D P o w e r D o w n
D o ze M o d e
U s e r D e fi n e
D i s a b le
D i s a b le
S u s p e n d
D i s a b le
M o d e
IPPC-7157 User Manual
34
I t e m H e lp
M e n u L e ve l
• Power Management: This option allows you to select the type (or
degree) of power saving for Doze, Standby, and Suspend modes. This
table describes the power management modes for your reference:
Max Saving
User Define
Min Saving
Maximum power savings. Only Available for SL CPUs.
Inactivity period is 1 minute in each mode.
Set each mode individually. Select time-out period in
the section for each mode stated below.
Minimum power savings. Inactivity period is 1 hour in
each mode (except the hard drive).
• HDD Power Down: When enabled and after the set time of system
inactivity, the hard disk drive will be powered down while all other
devices remain active.
• Suspend Mode: After the selected period of system inactivity, the
chipset enters a hardware suspend mode, stopping the CPU clock and
possibly causing other system devices to enter power management
modes.
• Doze Mode: After the selected period of system inactivity, the CPU
clock runs at slower speed while all other devices still operate at full
speed.
PM Control by APM
If Advanced Power Management (APM) is installed on your system,
selecting “Yes” gives better power savings. The Choices: Yes; No.
Video Off Option
This feature allows the VGA adapter to operate in a power saving mode
Always On
Suspend Æ Off
All Modes Æ Off
Monitor will remain on during power saving modes.
Monitor blanked when the systems enters the
Suspend mode.
Monitor blanked when the system enters either
Suspend or Standby modes.
35
Chapter 4
Video Off Method
This determines the manner in which the monitor is blanked.
V/H SYNC + Blank
Blank Screen
DPMS Supports
This selection will cause the system to turn off the vertical
and horizontal synchronization ports and write blanks to
video buffer.
This option only writes blanks to the video buffer.
Select this option if you monitor supports the Display Power
Management Signaling (DPMS) standard of the Video Electronics
Standards to select video power management values.
MODEM Use IRQ
This determines the IRQ which the MODEM can use.
The choices: 3; 4; 5; 7; 9; 10; 11; NA.
Soft-Off by PWRBTN
When Enabled, turning the system off with the on/ off button places the
system in a very low-powerusage state, with only enough circuitry receiving power to detect power button activity or Resume by Ring activity.
WAKE UP EVENTS
When this option is chosen, the following item appears for user’s configuration.
VGA
LPT & C OM
HD D & FD D
P C I M a s te r
IR Q s A c ti vit y
M o ni to ri ng
O ff
L P T /C O M
On
O ff
Ite m H e lp
M e n u L e ve l
P re s s E nte r
• VGA: When Enabled, you can set the VGA awakens the system.
• LPT & COM: When LPT & COM is ON, any activity from one of the
listed system peripheral devices or IRQs wakes up the system.
IPPC-7157 User Manual
36
• HDD & FDD: When HDD & FDD is ON, any activity from one of the
listed system peripheral devices wakes up the system.
• PCI Master: When PCI Master is ON, any activity from one of the
listed system peripheral devices wakes up the system.
• Primary INTR: When set to on, any event occurring at will awaken a
system which has been powered down.
On(default):The system can not enter the power saving mode when
I/O ports or IRQ# is activated. Off:The system still can enter the
power saving mode when I/O ports or IRQ# is activated.
• IRQ Activity Monitoring: The following is a list of IRQ’s (Interrupt
Requests), which can be exempted much as the COM ports and LPT
ports above can. When an I/O device wants to gain the attention of the
operating system, it signals this by causing an IRQ to occur. When the
operating system is ready to respond to the request, it interrupts itself
and performs the service. When set On, activity will neither prevent the
system from going into a power management mode nor awaken it.
When this option is chosen, the following item appears for user’s configuration.
IRQ-3 (COM2)
IRQ-4 (COM1)
IRQ-5 (LPT2)
IRQ-6 (Floppy Disk)
IRQ-7 (LPT1)
IRQ-8 (RTC Alarm)
IRQ-9 (IRQ2 Redir)
IRQ-10 (Reserved)
IRQ-11 (Reserved)
IRQ-12 (PS/2 Mouse)
IRQ 13 (Coprocessor)
IRQ 14 (Hard Disk)
IRQ 15 (Reserved)
3.
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Enabled
Disabled
Item Help
Menu Level
Press <ESC> to return to the Main Menu when you finish setting
up all items.
37
Chapter 4
4.7 PnP/PCI Configuration
PnP/PCI Configuration allows you to modify the system’s power saving
functions.
Run the PnP/PCI Configuration as follows:
1.
Choose“PnP/PCI Configuration”from the Main Menu and a list of
options will appear.
2.
Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.
PNP OS Installed
Reset Configuration Data
Resources Controlled By
IRQ Resources
DMA Resources
PCI/VGA Palette Snoop
Assign IRQ For VGA
Assign IRQ For USB
No
Disabled
Auto(ESCD)
Press Enter
Press Enter
Disabled
Enabled
Enabled
Item Help
Menu Level
PNP OS Installed
Select Yes if the system operating environment is Plug-and-Play aware
(e.g. Windows 95).
Note:
BIOS will automatically disable all PnP resources
except the boot device card when you select Yes
on Non-PnP operating system.
Reset Configuration Data
Normally, you leave this Disabled. Select Enabled to reset Extended System Configuration Data (ESCD), when you exit Setup if you have
installed a new add-on and the system reconfiguration has caused such a
serious conflict that the operating system cannot boot.
Resource Controlled By
The Plug and Play Award BIOS can automatically configure all the boot
and Plug and Play-compatible devices. If you select Auto, all the interrupt
request (IRQ) and DMA assignment fields disappear, as the BIOS automatically assigns them.
IPPC-7157 User Manual
38
IRQ Resources
Press Enter. Please refer to the list below:
IR Q - 9 a s s i g n e d to
P C I/ IS A P n P
Ite m H e lp
M e n u L e ve l
DMA Resources
Press Enter. Please refer to the below list.
DMA-0 assigned to
DMA-1 assigned to
DMA-3 assigned to
DMA-5 assigned to
DMA-6 assigned to
DMA-7 assigned to
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
Item Help
Menu Level
PCI/VGA Palette Snoop
This option allows the BIOS to preview VGA status, and to modify the
information delivered from the feature Connector of the VGA card to
MPEG card. This option can solve the display inversion to black after you
have used MPEG card.
Assign IRQ for VGA
Select Enabled if you system has a VGA controller and you have one or
more USB devices connected. If you are not using your system’s VGA
controller, select Disabled to free the IRQ resource.
Assign IRQ for USB
Select Enabled if you system has a USB controller and you have one or
more USB devices connected. If you are not using your system’s USB
controller, select Disabled to free the IRQ resource.
3.
Press <ESC> to return to the Main Menu when you finish setting
up all items.
39
Chapter 4
4.8 PC Health Status
This section helps you to get more information about your system including CPU temperature, FAN speed and voltage. It is recommended that
you contact your mainboard supplier to get proper values about the setting of the CPU temperature.
Run the PC Health Status as follows:
1.
Choose“PC Health Status”from the Main Menu and a list of
options will appear.
2.
Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.
Current CPUFAN1 Speed
Current CPUFAN2 Speed
Vcore
2.5V
3.3V
5V
12V
Item Help
Menu Level
Current CPU FAN1 Speed
Shows current CPU FAN1 speed. The fan must provide rotary pulse.
(Normally these types of fan have a three-wire connector)
Current CPU FAN2 Speed
Shows current CPUFAN2 speed. The fan must provide rotary pulse.
(Normally these types of fan have a three-wire connector)
Vcore/2.5V/3.3V/5V/1.2V
Shows power supply actual voltage value.
IPPC-7157 User Manual
40
4.9 Frequency/Voltage Control
Run the Frequency/Voltage Control as follows:
1.
Choose“Frequency/Voltage Control”from the Main Menu and a list
of options will appear.
2.
Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.
A u to D e c t D IM M / P C I C lk
S p r e a d S p e c tr u m
E n a b le d
E n a b le d
Ite m H e lp
M e n u L e ve l
Auto Detect DIMM/PCI CLK
To reduce the occurrence of electromagnetic interference (EMI), the
BIOS detects the presence or absence of components in DIMM and PCI
slots and turns off system clock generator pulses against empty slots.
Spread Spectrum
When the system clock generator pulses, the extreme values of the pulse
generate excess EMI. Enabling pulse spectrum spread modulation
changes the extreme values from spikes to flat curves, thus reducing EMI.
This benefit may in some cases be outweighed by problems with timingcritical devices, such as a clock-sensitive SCSI device.
41
Chapter 4
4.10 Load Optimized Defaults
When you press <Enter> on this item, you will get a confirmation dialog
box with a message similar to:
“ Load Optimized Defaults (Y/N) ? N ”
“Y” is for “Yes”, and “N” is for “No”.
Pressing “Y” loads the BIOS default values that are factor settings for
optimal performance of system operations.
4.11 Set Password
These option allows you to set your system passwords. The way to set up
the password is as follows:
1.
Choose “Change Password” in the Main Menu and press <Enter>.
Then following message appears:
“Enter Password : “
2.
The first time you run this option, enter your password up to 8 characters and press <Enter>. (The screen does not display the entered
characters.)
3.
After you enter the password, the following message appears
prompting you to confirm the password:
“Confirm Password : “
4.
Enter the same password “exactly” the same as you have just typed
to confirm the password and press <Enter>.
5.
Move the cursor to Save & Exit Setup to save the password.
6.
If you need to delete the password entered before, choose the
Supervisor Password and press <Enter>. It will delete the password
that you have entered before.
7.
Move the cursor to Save & Exit Setup to save the option you have
just configured; otherwise the old password will still be there the
next time you turn your system on.
8.
Press <Enter> to exit to the Main Menu.
Note: If you forget the password, access the system is to clear
the CMOS RAM. All setup information will be lost and you
need to run the BIOS setup program again.
IPPC-7157 User Manual
42
4.12 Save & Exit Setup
Save & Exit Setup allows you to save all modifications you have specified into the CMOS memory. Highlight this option on the Main Menu and
the following message appears:
“Save to CMOS and Exit (Y/N) ? Y “
“Y” is for “Yes”, and “N” is for “No”.
Press <Enter> key to save the configuration changes.
4.13 Exit Without Saving
Exit Without Saving option allows you to exit the Setup Utility without
saving the modifications that you have specified. Highlight this option on
the Main Menu and the following message appears:
“Quit Without Saving (Y/N) ? N “
“Y” is for “Yes”, and “N” is for “No”.
You may change the prompt to “Y” and press <Enter> key to leave this
option .
43
Chapter 4
IPPC-7157 User Manual
44
Appendix
A
LCD Specifications
and Selection Settings
Appendix A LCD Specifications
A.1 IPPC-7157 LCD Specifications
Model
IPPC-7157
Display
15" TFT LCD
Max. resolution
1024 x 768
Colors
16.2M colors (RGB 6-bit + FRC
data)/262k(RGB 6-bit) selectable
Dot pitch (mm)
0.297 (per one triad) x 0.297
Viewing angle
140 (H), 120 (V)
Luminance
250 cd/sq meter
Viewing area
304.128 (H) x 228.096 (mm
Power consumption
10.7 W (Typ.) @ 6.0mA (Gray
Bar Pattern)
Operating temperature
0 ~ 50°C
Storage temperature
-20 ~ 60°C
Backlight MTBF
60,000 hours
.
Note:
The color LCD display installed in the IPPC is of
high quality and reliability. However, it may contain a few defective pixels which may not always
illuminate. With current technology, it is impossible to completely eliminate defective pixels.
Advantech is actively working to improve this
technology.
IPPC-7157 User Manual
46
Appendix
Pin Assignments
B
Appendix B Pin Assignments
B.1 ATX Power Connector 1 (CN1)
Table B.1: AT Power connector 1 (CN1)
Pin
Signal
Pin
Signal
1
3.3V
11
3.3V
2
3.3V
12
-12V
3
GND
13
GND
4
5V
14
PS-ON
5
GND
15
GND
6
5V
16
GND
7
GND
17
GND
8
PW-OK
18
-5V
9
5VSB
19
5V
10
12V
20
5V
IPPC-7157 User Manual
48
B.2 ATX Power Connector 2 (CN2)
Table B.2: ATX power connector 2 (CN2)
Pin
Signal
Pin
Signal
1
GND
3
12V
2
GND
4
12V
B.3 LVDS Connector 1(CN4)
Table B.3: LVDS connector 1(CN4)
Pin
Signal
Pin
Signal
1
VDD
11
RXIN2+
2
VDD
12
RXIN2-
3
GND
13
GND
4
GND
14
RXIN1+
5
RXIN3+
15
RXIN1-
6
RXIN3-
16
GND
7
GND
17
RXIN0+
8
CLK0+
18
RXIN0-
9
CLK0-
19
DDC_CLK
10
GND
20
DDC_DAT
49
Appendix B
B.4 LVDS Connector 2 (CN6)
Table B.4: Table B.4: LVDS connector 2 (CN6)
Pin
Signal
Pin
Signal
1
VDD
11
RXIN6+
2
VDD
12
RXIN6-
3
GND
13
GND
4
GND
14
RXIN5+
5
CLK1+
15
RXIN5-
6
CLK1-
16
GND
7
GND
17
RXIN4+
8
RXIN7+
18
RXIN4-
9
RXIN7-
19
CONTRAST
10
GND
20
HPLG_DT
B.5 Inverter Power Connector (CN5)
Table B.5: Inverter power connector (CN5)
Pin
Signal
1
+12V
2
GND
3
ENABKL
4
Brightness Adj.
5
+5V
IPPC-7157 User Manual
50
B.6 FDD Connector (CN9)
Table B.6: FDD connector (CN9)
Pin
Signal
Pin
Signal
1
Vcc(+5V)
14
Step
2
Index
15
GND
3
Vcc(+5V)
16
Write data
4
Drive select
17
GND
5
Vcc(+5V)
18
Write enable
6
Disk change
19
GND
7
NC
20
Track 0
8
NC
21
GND
9
NC
22
Write protect
10
Motor on
23
GND
11
NC
24
Read data
12
Direction
25
GND
13
Density select
26
Side 1 select
51
Appendix B
B.7 Internal Speaker Connector (CN15)
Table B.7: Internal speaker connector (CN15)
Pin
Signal
1
Speaker out_R -
2
Speaker out_R +
3
Speaker out_L +
4
Speaker out_L -
B.8 IR Connector (CN24)
Table B.8: IR connector (CN24)
Pin
Signal
1
Vcc
2
NC
3
IR_IN
4
GND
5
IR_OUT
B.9 Fan Power Connector (FAN1 & FAN2)
Table B.9: Fan power connector (FAN1 & FAN2)
Pin
Signal
1
GND
2
+12V
3
FAN_DET
IPPC-7157 User Manual
52
B.10 COM1 RS-232 serial port (CN10)
Table B.10: COM1 RS-232 serial port (CN10)
Pin
Signal
1
3
5
7
9
DCD
2
TxD
4
GND
6
RTS
8
RI (RI/+5V/+12V)
Pin
Signal
RXD
DTR
DSR
CTS
B.11 COM2 (CN11)
Table B.11: COM2 (CN11)
Pin
Signal
RS-422
1
2
3
4
5
6
7
8
9
DCD
TXRX
TX+
TX
RX+
DTR
RXGND
GND
DSR
RTS
CTS
RI (RI/+5V/+12V)
RS-485l
DATADATA+
53
Appendix B
IPPC-7157 User Manual
54
Appendix
C
Keyboard Translator
Appendix C Keyboard Translator
C.1 Overview
The keyboard translator is an interface that switches the signal from the
membrane keypad to the standard AT keyboard. There are six connectors
on the board. On top of the board, there are two connectors linking two
flat cables to the membrane keypad (as shown in Fig. 4-3). On the side of
the board, there are four connectors.
The figure below shows the keyboard translator & the cable connection
for macro keys programming details.
IPPC-7157 User Manual
56
Caution:
Keyboard Translator(KBT-2002) can't be programmed through the USB
keyboard.
The step of programming the Macro Key(M1~M10) on the front panel:
1.
Open the front panel door, use a PS/2 keyboard connect to the
reserved external keyboard terminal of KBT-2002 which on the
back of front panel (see figure below).
2.
Boot up the system and enter the BIOS, check & make sure the
USB function is disabled.( This step is to avoid the influence or
interference caused by any USB keyboard or mouse device at the
later macro keys programming process)
3.
Run the Keyboard Translator Utility Program(Main.exe) under
DOS mode by using the connected PS/2 keyboard, and then edit the
function of front panel macro keys M1~M10 then programmed the
functions into KBT-2002. (Please be notified that the SF1~SF10 in
the utility program which is exactly mapping to the macro keys
M1~M10 on the front panel, please edit the function you need
accordingly.)
C.2 Programming the Front Panel Macro Keys
The Front Panel Macro Keys (M1~M10) could be programmed to have
specific function by running the "Keyboard Translator Utility", which can
be found at IPPC-7157 CD-ROM.
You can find Keyboard Translator Utility in the IPPC User CD:
\System Drivers\IPPC-7157A\Keyboard Translator
Driver\2053xxxxxx_Utility V1.5
And follow the instruction to complete the Keyboard Translator Utility
installation.
You can find out more details about KBT-2002 in the PDF document
which located in the below path of the IPPC User CD:
D:\System Drivers\IPPC-7157A\Keyboard Translator Driver\KBT-2002
Manual_ed1.pdf
57
Appendix C
C.3 Keyboard Translator Maintenance
(KBT-2002)
Below is the procedure of replacing the keyboard translator while needed:
1.
Switch off the power, and detach the main power cord.
2.
Unscrew the screws on front panel and open the front panel door of
IPPC-7157.
3.
The Keyboard Translator will be located on the back of the front
panel, behind the mylar protect. (Seebelow)
4.
Unscrew the screws on the mylar and remove it.
5.
Remove the keypad connector protective bracket.
6.
Carefully detach all cables connected to the keyboard translator.
7.
Unscrew the four screws on the corners, pull out the keyboard
translator,and replace it. right after that, reverse the step below to
re-install all things.
IPPC-7157 User Manual
58
Download PDF
Similar pages
Vantec CB-SP200
Installing the Suspend to IDE Hard Disk Utility on IWILL motherboard
Fellowes 9893501 User's Manual
V6-P8H61ELX BIOS UPDATE
S2-P8H61E BIOS UPDATE