Orion AVM-57188BTG User Guide Manual - CaRadio

AVM-57188BTG
DVD/VCD/CD/WMA/MP3 PLAYER WITH FM/MW RECEIVER
BUILT-IN NAVIGATION SYSTEM
INSTRUCTION MANUAL
PTY
TA
MIC
DISP
AF
OPEN
REL
VOL
DN
IR
UP
BAND/
NAV
MUTE
SRC
POWER
AV IN
PLEASE READ THIS MANUAL BEFORE USING THE EQUIPMENT.
Downloaded from Caradio-Manual.com Manuals
Thank you for buying this product, please read through these operating
instructions, so you will know how to operate your model properly.
After you have finished reading the instructions, put them away in a safe
place for future reference .
CONTENTS
PRECAUTIONS
1
FRONT PANEL
3
SYSTEM MENU
6
REMOTE CONTROL
10
BASIC OPERATION
13
RADIO OPERATION
14
BLUETOOTH OPERATION
16
DVB-T OPERATION
18
DVD/VCD/CD OPERATION
19
SYSTEM SETUP
22
MP3 OPERATION
26
NAVIGATION OPERATION
27
INSTALLATION
28
CABLE CONNECTION
30
ACCESSORIES
30
SPECIFICATION
31
TROUBLE SHOOTING
32
Note:
Due to continuous product improvement, specifications and design are
subject to change without prior notice.
Downloaded from Caradio-Manual.com Manuals
PRECAUTIONS
PRECAUTIONS
1. Be sure to connect the color coded leads according to the diagram.
Incorrect connections may cause the unit to malfunction or damage the vehicles
electrical system.
2. Be sure to connect the speaker (-) leads to the speaker (-) terminal.
Never connect the left and right channel speaker cables each other or to the vehicle body.
3.Make sure all the connections are completely correct before turning on your unit.
4. When replacing the fuse(s), the replacement must be of the same amperage as shown
on the fuse holder.
5. Do not block vents or radiator panels.
Doing so many cause heat to build up inside and may result in fire.
6 After completing the installation and beginning to play the unit
(including replacing the battery),
please press RESET button on the front panel with pointed object
(such as ballpoint pen) to set the unit to initial status.
Replaclng the Fuse
Make sure the amperage matches the specified value when replacing the fuses.
If the fuse is blown, check the power connection and replace with a new one.
If the same problem occurs, lt would be subjected to the malfunction in-house.
In such cases, please consult the nearest service dealer.
WARNING:
Never use the fuse with the rated amperage more than that supplied to your unit,
other wise lt will damage the unit.
IMPORTANT:
Please adjust screen to make the touching effect function best when you initiate
the unit for the first time.
For the details, please refer to the operation at Page 8.
1
Downloaded from Caradio-Manual.com Manuals
PRECAUTIONS
PRECAUTIONS
F This unit can play the following discs only:
Type of disc
Recorded material
Label on the disc
Size of disc
DVD
Sound and moving
pictures
12cm
VCD
Sound and moving
pictures
12cm
CD
Sound only
12cm
MP3
Sound only
12cm
NOTE: The unit is compatible with VCD1.0/2.0/3.0 version and DVCD disc.
Do not use your disc with paste
residue or ink attached.
Do not attempt to modify the
unit, modifying the unit may
cause an accident.
Stop the vehicle before carrying
out any operation that could
interfere with your driving.
Do not use disc with labels or
stickers attached, which may leave
a sticky residue while beginning to
peel off.
(Shown as the picture)
Do not work in extremely high or
low temperature. Be sure the
temperature inside the vehicle
is between +60 C and -10 C
before turning on your unit .
To enjoy optimum sound and
images while playing, handle the
discs as follows:
Clean the discs with an optional cleaning cloth. Wipe each disc
from the center out.
(Shown as the picture)
Handle the disc by its edge to
keep the disc clean, and do not
touch the surface.
2
Downloaded from Caradio-Manual.com Manuals
FRONT PANEL
FRONT PANEL
2
3
4
PTY
TA
1
19
18
17
MIC
DISP
AF
16
OPEN
15
14
REL
VOL
DN
IR
5
BAND/
UP
6
7
8
NAV
MUTE
SRC
POWER
9
AV IN
13
10
11
12
20 21
22
26
TILT
MENU
23
3
Downloaded from Caradio-Manual.com Manuals
24
25
FRONT PANEL
1. MIC
2. TA
Press this button to turn on/off TA function.
3. PTY
Press this button to select one of the
program type in RDS mode.
13. USB port
Insert USB device, the unit will play the files
from USB automatically.
4. REL
Press this button to open the front panel.
14.IR WINDOW
5. VOL
Adjust the volume by turning the knob
clockwise or counterclockwise. Press
this button briefly to display the menu.
You can choose one of the following
settings:
L-front/R-front/L-rear/R-rearsubwoof/
Bass / Middle / Treble / TILT/ Volume.
Rotate the button to adjust to the setting.
15.
Press the button to eject a disc when it is
loaded into the unit. Press and hold it to
force ejecting a disc when the system is
accidentally frozen.
16. OPEN
Press to open or close the TFT display.
6/7.
In radio mode, press one of these buttons
to seek a station manually.
Hold down one of the buttons to seek
a station automatically.
In DVD/USB/CARD mode press the
buttons to select the previous or next file.
Hold down the button for 2s to fast
forward or fast backward.
17. DISP/AF
Hold down the button to display the current
time, sources of front and rear displays and
medias (Disc, USB, SD) available.
Press this button to turn on/off TA function.
18. DISC Loading Slot
19. LCD display
8. BAND/ >II
In radio mode, press this button to select
the bands.
In play mode, press this button to
pause or resume playback.
20.Anti-theft led indicator
It will flash when the detachable control
panel is removed.
21. RESET
Using a sharp object such as a pencil to
reset the unit.
9. SRC/NAV
Press this button to select one of the
sources.
Press and hold this button to enter
navigation mode.
22. TFT display
23/24. TILT / /
/
Press
button to adjust the angle of
TFT display.
10.POWER/MUTE
Press the button to turn on the unit, press
and hold the button to turn off the unit.
When the unit is switched on, press the
button to shut off the sound output.
Press it again to resume the sound level.
25. MENU
In DVD mode, press the button to display
the DVD SETUP menu. Hold down the
button to display the SYSTEM SETUP menu.
In other modes, press the button to display
the SYSTEM SETUP menu.
11. AV IN
Connect the AV cable (supplied) to the
external AV device, then press the SRC
button to switch to AV1 mode.
26. GPS SD card slot
4
Downloaded from Caradio-Manual.com Manuals
12.SD slot
Insert an SD/MMC card, the unit will play
the files from SD/MMC card automatically.
NOTE: Once the SD/MMC card could not
eject after pressing, just pull it out manually.
SYSTEM MENU
The users can perform operation by touching screen directly.
RDS OPERATION
RADIO OPERATION
Display status of the disc
1
2
EON:OFF
3
1: 65.00M
2: 67.10M
3: 70.40M
4: 72.50M
5: 74.00M
6: 65.00M
P1
MONO
65.00MHz
Page1
4
5
1
2
3
8
9
10
PTY:
AF
PTY
Seek-
Seek+
Page2
4
5
1.TA
to turn on /off TA function
2.AF
to turn on /off AF function
3.PTY
to switch program type
4.Page2
to switch to radio operation page.
5.SEEK-/SEEK+
to seek a station automatically.
to seek a station manually(long touch).
1. LIGHT MODE
Touch this button to select day/night
light mode
2. Source
To display the SOURCE SETUP page
3.station preset button
to display the preset station list
(long touch to save the current
frequency into the station )
4.BAND
to switch bands.
5.LOC
to select local stations or distant station
6.EQ
to select a preset equalizer mode.
7.LOUD
to switch LOUD control function on/off
8.Page1
to enter RDS mode
9.SEEK-/SEEK+
Short press the buttons to seek a station
automatically.
Long press to seek a station manually.
10.AMS
to browse preset stations;
to search and store stations automatically
(long touch)
EON(Enhanced Other Networks)
ON:active the EON function,the unit
keep receive track of additional alternate frequencies to the AF list. If the
station being received does not broadcast the traffic information ,the receiver
automatically tunes in the related station that broadcasts the traffic information when it occurs
OFF:deactive the EON function
REG(Regional)
ON:active the REG function,the unit
automatically keeps receiving the related
RDS station.
OFF:deactive the REG function
5
Downloaded from Caradio-Manual.com Manuals
TA
MONO
65.00MHz
PS:
RT:
6
7
P1
REG:OFF
PTY:NONE
SYSTEM MENU
SETUP OPERATION
MULTI-- PLAYER OPERATION
TOUCH ON THE TOP LEFT POSITION
TO ENTER SOURCE INTERFACE.
The unit will return to previous mode
display screen if any operation is not
perform in 5 seconds.
In DVD mode, the touching screen displays
as following after touch at random position.
PLAY
PAUSE
STOP
PREV
1
2
3
NEXT
SETUP
4
5
Front
Rear
Audio
Video
SYS
Exit
6
5
4
1
2
3
1. Front
1.PLAY
To display the front source selection screen.
To start the playback.
2.PAUSE
To pause the playback.
3.STOP
To stop playing, touch twice to stop completely.
4.SETUP
To display the DVD SETUP screen.
5.PREV/NEXT
Touch the item to select source displayed
To select previous/next chapter or tracks.
on the unit screen.
Front
NOTE: Touching the left middle position
twice to display the TITLE MENU selection
screen, touching the right middle position
twice to display the ROOT MENU selection
screen, touching the right top position to
display the number keyboard.
You can select chapter(track) by pressing
the touchable screen or the RC.
Rear
Video
SYS
Exit
2.Rear
To display the rear source selection screen.
12:20:25
Front:Disc
Drive:Disc
Front
6
Downloaded from Caradio-Manual.com Manuals
Audio
Rear
Audio
Video
SYS
Exit
SYSTEM MENU
SYSTEM SETUP OPERATION
3.Audio
Touch on the AUDIO button and the
screen will display as following:
Clock Sys
Key Beep
Local Area
Volume
Front
Rear
Audio Video
SYS
Exit
L-front
Volume:19
Clock Sys
Set the time display mode(12H/24H)
R-front
Front
Rear
Audio Video
SYS
Exit
Key Beep
Turn on/off the sound guide function
ON: Activate the sound guide mode
OFF: Deactivate the sound guide mode.
The sound guide beep will be OFF
when any button on the unit is pressed.
In this menu, there are items of Volume,
L-front,R-fornt, L-rear, R-rear, Subwoof,
Bass, Middle and Treble can be adjusted.
Touch on the
button to adjust each
item and touch on
button to turn
pages and select the item listed above.
Local Area
Touch the provided option to change
the radio frequency for different country.
4.Video
Press on the VIDEO button and the
screen will display as following:
Bass freq
Bright
Middle freq
HUE
Treble freq
Contrast
Bright 30
Front
Sharp
Front
Rear
Audio Video
SYS
Rear
Audio Video
SYS
Exit
Exit
Touch the provided option to adjust the
bass freq, middle freq, treble freq.
In this menu, there are items of Bright,
Hue, Contrast, Sharp can be adjusted.
Touch on the item that need adjusted
then touch on the
button to adjust.
Subwoof freq
5.SYSTEM
To display the system setup screen.
Refer to SYSTEM SETUP OPERATION.
BassQ factor
MidQ factor
Front
Rear
Audio Video
SYS
Exit
6.EXIT
To return to current source screen.
Touch the provided option to change the
subwoof freq ,the bass and middle quality
factor.
7
Downloaded from Caradio-Manual.com Manuals
SYSTEM MENU
GPS Mix SW
Clock Adjust
SW Control
Night Lum
GPS Volume
Touch Adjust
Front
Rear
Audio Video
SYS
Front
Exit
Clock Adjust
adjust the time by touch
Audio Video
SYS
Exit
GPS Mix SW
ON:the navigation guidance does not
interrupt the head unit
OFF: the navigation guidance interrupts
the head unit. Audio of the head unit is
muted at this time.
To select item your want to set
(hour, minute, second)
to change the display number
Night Lum (dimmer)
The function to select the backlight
brightness.(normal status's 20%,40%,
60%,80% )
SW CONTROL
The function to select the steer wheel
control. Refer to next page.
Touch Adjust
when the display position on the screen
and the touch position on the touch
panel not match, or using the product
at first time, the adjustment becomes
necessary.
GPS Volume
The function to sets the volume level
of the outputs sound through the
navigation source.
(High/Mid/Low)
X < - press it
Accurately touch the X mark provided
in the screen for more than 2 seconds
until the adjust succeed is displayed.
8
Downloaded from Caradio-Manual.com Manuals
Rear
SYSTEM MENU
SW Control
SW CONTROL INSTALLATION
To set 8 short-cut bottons for the
steering wheel remote control.
Before installing the SW control,
please make sure all the wires are
in good condition.
For installation, please refer to the
illustrations below:
1. NO KEY
in case of connecting to the SWC
(steering wheel control):
2. NO KEY
Audio Video
SYS
Exit
Key1
GND
The screen will display NO KEY if there
is no set for the system.
There are 12 buttons for selection in
each item: POWER, MODE, STOP,
PREV, NEXT, VOL+,VOL-, MUTE, EJ,
PAGE UP, PAGE DOWN and MENU.
GND, black
X
Key2
CAR AUDIO
SWC2, brown
SWC
in case of connecting to the SW
remote control:
Please refer to the following sequential
order to finish the setting:
1. Touch on NO KEY position on the screen;
2. Press one button on the SW control;
3. The function list jumps out on the screen;
4. Touch one of the functions as the
wanted function for the pointed button
on SW control;
Key1
GND
Key2
B+
SW remote control
IR
X
SWC(IR), Blue/yellow
CAR AUDIO
GND
Please consult the professional
technicians for advice if the unit can
not work as expected.
Note:
1.The group-setting can be erased by
pressing and holding the selected group.
2. If there is already a set item, press the
corresponding button on the SW control
and the screen will display: set in X.
3. Each function can be selected into one
or more than one button of the 8 buttons
on the SW control while one button can
only be pointed as one function.
9
Downloaded from Caradio-Manual.com Manuals
SWC1, orange
X
Rear
X
3. NO KEY
Front
REMOTE CONTROL
REMOTE CONTROL
Installing the battery
Slide the tray out on the back of the
remote control and insert the battery
with the plus (+)and minus(-)poles
pointing in the proper direction.
Use and care of the remote control
NAV
PTY
AF
TA
Point the remote control in the direction
of the front panel to operate to use it.
Notes:
Using batteries improperly can cause
them to explode. Take note of the following points:
* Keep the battery out of the reach of
children. Should the battery be swallowed, immediately consult a doctor.
* Use one CR2025(3V)lithium battery.
* Remove the battery if the remote control is not to be used for a month or
longer.
* Do not short-circuit, disassemble or
heat batteries.
* Do not dispose of batteries into fire or
flames.
* Dispose of spent batteries properly.
* Do not let the remote control fall onto
the floor, where it may become jammed under the brake or accelerator
pedals.
ST
IR-SW
1.PWR/
3. ANGLE/AMS
5. PROG/A-B
7. GOTO/#
9. [ / ][ / ][ / /
10. RPT/NAV
/PTY
11.
13. SRC
15.
17. 0-9 Number button
18. CLEAR
20. TITLE
22. BAND/P/N
24. AUDIO/ST
2. EQ
4. SUB-T/LOC
6. OSD/*
8. MENU
/ ]/ENTER
12. ZOOM/AF
14. VOL-/SEL/VOL+
16. LOUD
19.
21.
23. SETUP
25. RDM/TA
10
Downloaded from Caradio-Manual.com Manuals
REMOTE CONTROL
3. ANGLE/AMS
In DVD mode, press to change the
viewing angle ;
In radio mode, press to browse each
stored station .Long press to scan and
store station automatically.
In TV mode, long press the button to
scan and store channel automatically.
7. GOTO/ #
In DVD mode, press the button and the
cursor button to select TITLE, CHAPTER,
AUDIO, SUBTITLE,ANGLE ,TT TIM E,
CH TIM E, REPEAT, TIME DIS P. Then
press ENTER button to set the value.
In VCD mode, press GOTO button and
cursor button to select TRACK, DISC
TIME, T RACK T IME, REPEAT, T IME
DIS P. Then pres s ENTER button to set.
In CD/MP3 mode, press GOTO button
to select "Disc Go To:_ _ _", "Track Go
To _:_ _:_ _", Select Track:_ _:xx".
Then press 0-9 number buttons to set
the track you want.
In bluetooth mode, press this button to
function as # button on your mobile
phone functions .
In radio mode ,press the button and the
number button to set the frequency.
In TV mode ,press the button and the
number button to select a channel.
4. SUB-T/LOC
In DVD playback mode, press to change
the subtitle language; In radio mode,
press to select strong or weak station
reception.
8. MENU
In DVD mode, press to return to the root
menu.
In radio mode, press this button to switch
between RDS and radio modes.
5. PROG/A-B
In playback mode, press to set the program order to play; In playback mode,
press and hold to play the section of
selected chapter/track repeatedly .
9. [ / ][ / ][ / / / ]/ENTER
In playback mode ,to perform these
function as following: play fast reverse/
fast forward, find the beginning of previous chapter or track/find the beginning
of the next chapter or track
In raido (TV)mode,to search for a station
(channel),recall a prest station(channel)
In DVD setup, use the triangle buttons
to navigate file lists and the setup menus.
1. POWER/
Press the button to turn on the unit;
Press and hold to turn off the unit.
In power on,press to mute the device.
Press it again to resume previous sound
level.
2. EQ/
Press to select the corresponding preset
modes to adjust the sound quality.
In bluetooth mode, press this button to
dial up a call or receiving a call.
6. OSD/*
In playback mode, press to display the
playback information;
In other mode, press to display the
current time, the set source output
through the front and rear display, the
current available drive.(Disc/SD/USB);
In bluetooth mode, press to function as
* button on your mobile phone functions .
10. RPT/NAV
In playback mode, press to select a repeat
mode.
Press and hold this button to start the
navigation mode.
11
Downloaded from Caradio-Manual.com Manuals
REMOTE CONTROL
11.
/PTY
In radio mode, press to switch the RDS
program type.
In DVD/VCD mode, press to play slowly.
18. CLEAR
Press the button to clear the erroneous
number what you import.
19.
Press to pause playing and press again
to resume playing.
12. ZOOM/AF
In radio mode, press to function AF on/off.
In DVD/VCD mode, press to increase
or decrease the picture in size.
20. TITLE
In DVD mode, press the button to return
the title menu.
In VCD mode, press this button to turn
on/off PBC function.
13. SRC
Press the button repeatedly to switch
sources.Press and hold this button to
change the IR to control front or rear
source.
21.
Press to stop playback.
14. VOL-/SEL/VOL+
Press VOL-/VOL+ to adjust volume.
Press SEL to select one of the control
item:L-front/R-front/L-rear/R-rear/Subwoof/Bass/Middle/Treble/Angle/Volume.
Then press VOL+/- to adjust each item.
22. BAND/P/N
In radio mode,press to select bands.
In DVD/VCD mode,press P/N button to
select PAL AUTO or NTSC.
23. SETUP
In playback mode, short press to display
DVD setting, long press in DVD mode
and press in other modes will display
system settings.
15.
Press to eject a disc
16. LOUD/
Press this button to activate LOUD
function.
In bluetooth mode, press to hand up
your calling.
24. AUDIO/ST
In DVD mode, press to change the audio
language.
In VCD mode ,press to change the channel
mode.
In FM mode, press to select stereo or mono
reception.
17. (0-9)NUMBER BUTTON
In radio(TV) mode,press the number
button to select a corresponding preset
station(channel)
In DVD/VCD/CD mode,press to select
any chapter or track directly.
In bluetooth mode ,press to input the
telephone number.
25. RDM/TA
In radio mode, press to function TA o/off.
In playback mode, press to play tracks in
a random order.
12
Downloaded from Caradio-Manual.com Manuals
BASIC OPERATION
1.Reset the Unit
When operating the unit for the first
time or after replacing the car battery,
you must reset the unit.
Remove the guard against theft front panel
at first, then press RESET button
with a pointed object, (such as a
ball-point pen) to set the unit to initial
status.
This function can only be operated
by the head unit.
Note:
* After selecting the desired mode,
you can adjust the current level by
pressing VOL buttons on the
remote control.
* If you don,t adjust VOL button in 3
seconds after selecting the desired
mode, the unit will automatically
return to the current mode being
displayed.
5.Turning Loudness On/Off
Short press LOUD button on the remote
control to activate loud function.
Press it again to shut down LOUD
function.
2.Turning the Unit On/Off
Press PWR button to turn on the unit.In
unit ON,when insert a disc,the unit will
automatically start playing.
Long pressing it to turn off the unit
completely.
Pressing PWR button on the head unit
also performs the same operation.
6.EQ Setting
While listening to music, you can
select the corresponding preset
(popular/classic /rock) modes, you can
adjust the sound texture more precisely
by using EQ button on the remote control.
Repeatedly pressing EQ button to
choose the following modes in turn:
3.Volume Control
Press VOL+ button on the remote
control to increase the sound level and
press VOL- button on the remote
control to decrease the sound level.
Rotating VOL button on the head
unit or touching the VOL-/VOL+ on the
TFT panel also performs the same
operation.
POP
EQ OFF
4.Setting the Sound Characteristics
Repeatedly press SEL button to select
the desired mode in the following order:
L-front
Volume
R-front
TILT
L-rear
Treble
R-rear
Middle
Subwoof
Bass
13
Downloaded from Caradio-Manual.com Manuals
CLASSIC
ROCK
RADIO OPERATION
Select radio mode
Press SRC button on the remote control
or on the panel to select RADIO mode.
NOTE: Touch on left top area of the
screen to display the sources screen
then RADIO mode can be selected.
1: 65.00M
2: 67.10M
3: 70.40M
4: 72.50M
5: 74.00M
6: 65.00M
P1
3.Recalling a preset station
A total of 30 preset stations (18-FM,12-MW)
are available in memory.
Press / button on the remote control
to recall a preset station.
The display shows the preset number and
frequency of the stored station, touch one
of these to select a corresponding station
for listening.
Note: Press any one of the station preset
buttons on the remote control also selects
preset station.
MONO
65.00MHz
Page1
1.Band Select
In radio mode, repeatedly press BAND
button on the remote control to select
a band in the following order:
FM1
MW2
4.Store stations
4.1 Auto store
It is a function for storing up to 6 stations.
Follow the two steps:
Select the desired band;
hold down AMS button,the stations with
good reception are stored automatically.
4.2 Manual store
To turn in a station to be stored in the preset
memory, press and hold any one of the preset
buttons (1-6) to store on.
*If a new station will be stored in a preset
memory which already has a station, the
current station will be cleared and replaced
by the new station.
FM3
FM2
MW1
Note: Press BAND on the touch screen or
on the panel also performs the same
operation.
2. Tuning
2.1 Automatic Tuning
There are three ways to tune in a station
downwards automatically as below:
press
button on the remote control;
press
button on the panel;
touch on SEEK- button on the touch screen.
There are three ways to tune in a station
upwards automatically as below:
press
button on the remote control;
press
button on the panel;
touch on SEEK+ button on the touch screen.
2.1 Manual Tuning
There are three ways to tune in a station
downwards manually as below:
press and hold
button on the remote
control;
press and hold
button on the panel;
touch on SEEK- button on the touch screen.
There are three ways to tune in a station
upwards automatically as below:
press and hold button on the remote
control;
press and hold
button on the panel;
touch and hold on SEEK+ button on the
touch screen.
5.DX/LOC Selector
In radio mode, press LOC button on the
remote control to select strong or weak
station reception.
5.1 LOC
When LOC:ON displays on the touch screen,
only strong signal stations will be tuned.
5.2 DX
When LOC:OFF displays on the touch screen,
both strong and weak stations can be received.
Note:
* The initial mode is DX mode.
6.MO/ST Selector
In FM of radio mode, you can press ST
button on the remote control to select
Mono mode or Stereo mode.
14
Downloaded from Caradio-Manual.com Manuals
RADIO OPERATION
RDS (RADIO DATA SYSTEM) OPERATION
The RDS allows you to receive a
variety of information such as traffic
information,station names,and to
automatically retune to a stronger
transmitter that is broadcasting the
same programme.
Tips
The RDS digital data includes the followings:
PI Programme Identification
PS Programme Service Name
AF List of Alternative Frequencies
TP Traffic Programme
TA Traffic Announcement
PTY Programme Type
EON Enhanced Other Networks
Turn on/off the AF function
* Press AF button to switch on/off AF
function
*The tuner will search for a station with
RDS information
* The tuner will retune frequencies when
ever the reception signals getting worse.
Receiving Traffic information
1.Press the TA button to switch on TA
mode.
2.The unit search for traffic information
station automatically. When a traffic
information station is tuned in, the TP
mark display on touchable screen. If you
do not want to listen to the traffic information
being received, press TA button to skip that
traffic information message.
The TA function will remain in the ON
position. And the unit will be back to
previous mode.
3.Press it again to switch off TA mode.
EON:OFF
P1
REG:OFF
PS:
RT:
TA
MONO
65.00MHz
PTY:NONE
PTY:
AF
PTY
Seek-
Seek+
Page2
1.Press PTY button on touchable screen
or on the remote control to select a programme type. After selecting the programme type for 3 seconds, the unit will
search for a station in the selected programme type.
*If the PTY station is found,the tuner
will be stop searching.
*If the PTY station is not found, No Pty
will be display on the screen.
All types for your selection are listed in
table as below:
NEWS
ROCK MUSIC
PHONE IN
CURRENT AFFAIR
M.O.R. MUSIC
LIGHT CLASSIC
TRAVEL
LEISURE
INFORMATION
SPORTS
EDUCATION
SERIOUS CLASSIC JAZZ MUSIC
OTHER MUSIC
COUNTRY
DRAMA
WEATHER
CULTURE
FINANCE
NATIONAL
OLDIES
SCIENCE
VARIED
POP MUSIC
CHILDREN
SOCIAL AFFAIR
RELIGION
FOLK
DOCUMENTARY
ALARM
TEST
An emergency broadcasting(ALARM)
will broadcast automatically and produce the beep sound when it is received.the sound output through other
source will be muted.
* Traffic information is heard only when
it is being broadcast.
In other mode, Traffic announcement
can interrupt the source sound output
when broadcast. After broadcasted ,the
unit will automatically return to the original
source play before the traffic information
broadcast began.
15
Downloaded from Caradio-Manual.com Manuals
PTY(Programme Type)Tuning
The PTY function allows you to search
for stations with a particular Program
Type. Touching Page1 button on the radio
display screen to switch to the RDS screen.
BLUETOOTH OPERATION
HANDS-FREE PHONE
*The Bluetooth setting is required for a
mobile phone. Read the Owner ,s Manual
of the mobile phone.
*After paired ,the unit can connect with
the mobile phone automatically. in valid
range
* If the mobile phone or the device is
disconnected with the unit accidentally,
the screen will display Disconnect, just
press LINK button on the screen to reconnect(refer to Bluethooth setup ).
The unit is compatible with Bluetooth
international standard wireless
cummunication technology.
You can place a hands-free call by a
Bluetooth compatible with the mobile phone.
*When you place a call, speak loudly
and clearly.
*Shut the windows before calling.
*It is normal that some unnatural
voice may be heard during your calling
which may be caused by the conditions
of the signals or the one who use the
mobile phone.
*Due to some special mobile phone,
you may not be able to use a hands-free
phone.
Dialling a call
1.Input the number required by pressing
number button on the remote control or
on the screen then press
button on
the screen to dial up.
The telephone number you dialed is
appeared on the screen
CONNECTING
Selecting BT mode
Press PAIR button on touchable
screen to turn on the pair function.
Searching for device by using
mobile phone.
2.Placing a call by history:
Press
button to switch to PHONE
BOOK screen.you can place a call by
selecting a person from a list of received
calls, dialed calls or missed calls.
A maximum of 16 numbers can be stored in each call history. A maximum of 4
numbers be display in each page, and
touching
button to turn to next page.
Selecting bluetooth device
by using mobile phone.
Input a pass code:1234.
The connection is done.
The screen display Connect.
Hanging up a Call
Press
button on the screen to finishes the call.
16
Downloaded from Caradio-Manual.com Manuals
BLUETOOTH OPERATION
Receiving a Call
When a call is received, a received call
sound rings ,and the calling is announced
in the display. Press
button on
the screen to starts the call.
BLUETOOTH AUDIO FUNCTION
Audio information of a bluetooth
compatible mobile phone,portable
player,etc.,is by wireless controllable/playable from the unit.
*Press / button on the remote
control also perform dial(receiving)
a call or hang up a call function
*The incoming call will interrupt the
sound output through other source,
and switch to the hands-free phone
screen automatically when it is received.
Refer to CONNECT to connect
bluetooth audio devices.
Refer to bluetooth setup(PAGE 7) for
operation
*video playback is not supported.
*using remote control also perform same
operation
After the call is over, the unit will be
back to previous mode.
* The hands-free phone sounds output
through the built-in speakers.
When calling, press
button on the
screen to switch the mode to receive
a call by using mobile phone, and
press it again to return to hands-free
mode.
The key of the remote control assigned
in Bluetooth audio function
Play/pause
Previous/next track
Stop playback
17
Downloaded from Caradio-Manual.com Manuals
TV OPERATION
TV OPERATIONS
0: 44.25
1: 55.75
2: 63.75
3: 77.25
4: 44.25
5: 115.25
PAL-BG
Ant-1
CH-
CH+
AMS
CH:0
44.25Mz
Seek-
Seek+
SYS
1. Select TV mode
Press SRC button on the remote control
or on the panel to select a source of TV.
NOTE: Touch on left top area of the
screen to display the sources screen
then TV mode can be selected.
2. Select a channel
To select a desired channel, the user can
choose one of the following ways:
2.1. By Remote control
Press
or
on the remote control
to select previous or next stored channel.
2.2. By Remote control
Press(1-9) number button directly
on the remote control to select a preset
channel.
To select more than 10 channel number,
firstly press GOTO button on the remote
control, then press the corresponding
number buttons.
2.3. By Touch screen
Touch on the needed channel number
on the screen.
Touch on CH-/CH+ button on the screen
to turn pages to select the exact channel.
4. Search a channel
4.1 Automatic Searching
There are three ways to search a channel
downwards automatically as below:
press
button on the remote control;
press
button on the panel;
touch on SEEK- button on the touch screen.
There are three ways to search a channel
upwards automatically as below:
press
button on the remote control;
press
button on the panel;
touch on SEEK+ button on the touch screen.
4.1 Manual Tuning
There are three ways to search a channel
downwards manually as below:
press and hold
button on the remote
control;
press and hold
button on the panel;
touch on SEEK- button on the touch screen.
There are three ways to search a channel
upwards automatically as below:
press and hold button on the remote
control;
press and hold
button on the panel;
touch and hold on SEEK+ button on the
touch screen.
5.Store channels
5.1 Auto store
Press and hold AMS button on the remote
control OR on the touch screen for 2 seconds.
The unit will search for channels and store
them under preset numbers in order of
signal strength.
5.2 Manual store
Follow the two steps:
Find a channel you want to store;
Press a preset number button on the touch
screen, under which you want to store
the channel.
3.Selecting TV system
Touch repeatedly SECAM-DK button on
*If a new channel will be stored in a preset
the screen OR press on BAND/P/N button
memory which already has a station, the
on the remote control to switch TV system.
current channel will be cleared and replaced
by the new channel.
Note: When the TV channel picture
is being broadcast, touch on the
random area of the screen to return to
the TV mode menu.
18
Downloaded from Caradio-Manual.com Manuals
DVD/VCD/CD OPERATION
DVD OPERATION
5.Playing Tracks in Random Order
During VCD/CD playback, when pressing
RDM button, RANDOM will
appear on the display, the unit plays
any track at random and the number
selection is unavailable. Press it again
to return to normal playing.
1.Basic operation
(1) Insert a disc into the disc loading
slot,the unit will play automatically
* You can eject a disc by pressing
button.
(2) Use the VOL+/ VOL- to adjust the
sound level.
Rotating (VOL+ or VOL-) on the head
unit or touching VOL-/VOL+ button on
the TFT panel performs the same
operation.
6.Repeat Playing
In playback mode, press RPT on the
remote control to perform replaying
function when you need to repeat the
chapter you like.
*The initial repeating mode is all
During DVD playback,the replay option
change in following order:
TITLE
CHAPTER
2. Skip backward/forward/F.F/F.REW
To skip back or forward to another
track or chapter, press
or
.
Press
or
to perform fast reward
or fast forward.repeatly press the button
the options switch as follows order
2X
4X
8X
16X
OFF
during VCD/CD playback,the replay
option change in following order
32 X
OFF
TRACK
*Pressing
/ / /
button on the
head unit performs the skip reward/forward operation.
*Long pressing
/ /
/
button
on the head unit performs the fast
reward/forward operation.
7. Slow motion playback
In VCD mode, press
to slow
forward. There are 4 speeds each press
decreases the speed until the minimum
speed is reached.
1 16
18
12
14
3. Stop the playback
Press
button to set the unit in prestop status,then press ENTER button
to play the current chapter or track,
press stop button twice to stop playing
completely,then press ENTER button
to play the beginning of disc.
Normal Play
In DVD mode, press
to slow
forward or slow reward.
1 16
18
12
14
Normal Play
1 16
18
14
*This function is operated by using the
remote control.
8.Increase the size of the picture
Press ZOOM to increase the picture in
size.There are 6 sizes, Each press
increases the size until the maximum
size is reached.
12
13
14
3X
2X
4X
OFF
4.Pause the Playback
Press
button to suspend the playback, Press it again to return to normal
playback.
*Pressing
button on the head unit
performs the same operation.
*This function is operated by using
the remote control.
19
Downloaded from Caradio-Manual.com Manuals
12
DVD/VCD/CD OPERATION
12.Changing the audio language
Can be done by pressing the AUDIO
button to switch between languages
and audio systems during playback.
Selection options switch as follows:
9.On-screen display
In DVD mode, press to display Title
Elapsed, Title Remain, Chapter
Elapsed, Chapter Remain, Display Off.
In VCD/CD mode, press to display
Single Elapsed, Single Remain, Total
Elapsed, Total Remain, Display Off.
This function is operated by using
the remote control.
* This function can only be operated by
using the remote control.
Audio 01
This function is operated by using the
remote control.
Notes:
This function only operates with DVDs
featuring multi-audio recordings.
10.Programmed playback
In DVD/VCD/CD mode, press the PROG
button and the program menu will be
displayed. Press the number buttons to
select the track number. Use the direction
buttons to move the cursor to START
and press ENTER to start programmed
playback. Move the cursor to EXIT and
press ENTER to exit the programmed
playback. Move the cursor to REW and
press ENTER to go to the last page;
move the cursor to NEXT and press
ENTER to go to the next page. During
this process, press PROG to cancel
the programmed playback.
* This function can only be operated
by using the remote control.
13.Selecting different title (DVD mode)
On a DVD disc, you can press TITLE
on the remote control to return the root
menu of the disc, and you can select
different chapters or titles upward or
downward by using
or
.
*This function is operated by using the
remote control.
14.Selecting root menu(DVD mode)
For DVD disc, you can press MENU
to select different root menus, and
then press
[ENTER] buttons
to enter the sub-menus. Press
buttons, and the number
buttons, and then ENTER button to
select and enter what you desire.
11.Changing the subtitle language
(Multi-subtitle)
With DVDs featuring multi-subtitle
data. You can press SUB-T to switch
between subtitle languages during
playback.
Options selection is as follows:
Subtitle 01
Subtitles 02
15. SETUP MENU
In DVD/VCD/CDmode, press SETUP,
the screen will display the system
setting picture, the user can select
some relative constant parameters.
The user can also set them as needed
by moving the cursor and using
buttons, and then press
ENTER to validate the actions.
This function is operated by using the
remote control.
Notes:
*The selections are the preferred options
that will be chosen if they are available
on a disc. If the disc that is inserted does
not have the preferred option then the
Subtitles OFF
This function is operated by using the
remote control.
Notes:
*This function only operates with DVDs
featuring multi-subtitle.
20
Downloaded from Caradio-Manual.com Manuals
Audio 02
DVD/VCD/CD OPERATION
18. Changing the viewing angle
(Multi-angle)
With DVDs featuring multi-angle (scenes
shot from multiple angles) recordings,
press the ANGLE button to switch between viewing angles during playback.
The viewing angle changes in the following order:
ANGLE1-ANGLE2-ANGLE3
Note:
* This function is operated by using the
remote control.
* This function is only available with
DVDs featuring multi-angle recordings.
* The
symbol on a DVD packaging
indicates that it features multi-angle
scenes. The number in the
symbol
indicates the number of angles from
which scenes were shot.
* The ANGLE button does not function
during fast forward/fast rewind or pause.
discs own preferencewill be used.
*Regarding SETUP MENU, please refer to
the following pages for more details.
*Some functions may vary depending on
the types of models or formats of the disc.
15.Auto switch to video
When driving a car, in DVD/SD/USB
and video active mode, TFT display
Attention:Cannot use this function
When driving Just braking car,
the TFT can switch to video automatically.
16.Auto switch to video when
revering the car
When reversing, the unit can switch to
reversing video display automatically
so you can see behind of the vehicle if
cameras have been set up, and the
sound will be shut off.
17.Selecting an acoustic output mode
In VCD mode, press the AUDIO button
on the remote control repeatedly to select
an audio mode in the following order:
MONO RIGHT
MONO LEFT
STEREO
MIX-MONO
21
Downloaded from Caradio-Manual.com Manuals
SYSTEM SETUP
Some DVD titles may be recorded in special
formats. In such cases, the DVD titles will
always appear on the screen in their original
format,regardless of which TV display format
you select.
SYSTEM SETUP
When you press SETUP button on the
remote control or press MENU button on the
panel, the setup menu will be displayed. It include General Setting, Audio Setup, Video Setup, Preference Setup, Password Setup and
1.2 OSD LANGUAGE
Exit Setup menu.
1.Within the setup menu, you can use [ ]
On Screen Display(OSD)Language:Users
[ ][ ][ ] buttons on the remote control
can select the whole setup menu and
to move the cursor,and then press the
on-screen display language.
ENTER/PLAY button to make your selection.
Press [ ] can return to the previous menu.
GENERAL SETUP PAGE
2.To exit setup menu, you can select the
TV DISPLAY
WIDE
EXIT SETUP item in sub-menu or press SETUP
ENGLISH
OSD LANGUAGE
ENG
button or press MUNU button on the panel.
*Touching the item on the screen also preform
same operation
SET OSD LANGUAGE
1. GENERAL SETUP PAGE
Setup TV screen format,video type and all
DVD functions.
2. AUDIO SETUP PAGE
1.1 TV DISPLAY
User can select digital audio setup or dolby
digital setup.
GENERAL SETUP PAGE
TV DISPLAY
WIDE 4:3 PAN SCAN
OSD LANGUAGE ENG 4:3 LETTER BOX
16:9 WIDE
AUDIO SETUP PAGE
DOLBY DIGITAL SETUP
SET TV DISPLAY MODE
The TV Display which select the different
ratio of display format and the screen of
TV, There are various types of display on
screen for different matches between Disc
and TV.
Note:
No matter which display format is selected,
a picture recorded in standard 4:3 format
always displays in the 4:3 aspect ratio.
The display format of DVD titles may vary;
please refer to the information that accompanies your specific DVD title.
If the DVD title is recorded in 16:9 wide
display format while the TV is a standard
4:3 screen, horizontal compression of the
image will result.
22
Downloaded from Caradio-Manual.com Manuals
GO TO AUDIO SETUP PAGE
SYSTEM SETUP
2.1 DOLBY DIGITAL SETUP PAGE
3. PREFERENCE SETUP PAGE
3.1 AUDIO
AUDIO SETUP PAGE
DOLBY DIGITAL SETUP
AUDIO: Sets the preferred audio language as the
default when playing DVD. (IF DVD support these
languages)
GO TO SPEAKER SETUP PAGE
PREFERENCE PAGE
ENG
AUDIO
ENG
SUBTITLE
ENG
DISC MENU
PARENTAL
DEFAULT
2.1.1 DUAL MONO
DOLBY DIGITAL SETUP PAGE
DUAL MONO
DYNAMIC
STR
STEREO
L-MONO
R-MONO
MIX-MONO
ENGLISH
FRENCH
SPANISH
PORTUGUESE
JAPANESE
KOREAN
RUSSIAN
THAI
PREFERRED AUDIO LANGUAGE
3.2 SUBTITLE
DUAL MONO(1+1) SETUP
Users can switch the binaural mode among
STEREO, L-MONO, R-MONO and MIX-MONO.
2.1.2 DYNAMIC:
select the provided option to change the
Dynamic rang e setting.
SUBTITLE: Sets the preferred subtitle language as
the default when playing DVD.(if DVD support these
languages)
PREFERENCE PAGE
AUDIO
ENG
ENG
SUBTITLE
ENG
DISC MENU
PARENTAL
DEFAULT
ENGLISH
FRENCH
SPANISH
PORTUGUESE
JAPANESE
KOREAN
RUSSIAN
THAI
PREFERRED SUBTITLE LANGUAGE
3.3 DISC MENU
DISC MENU: Sets the preferred menu language as
the default when playing DVD.(if DVD support these
languages)
PREFERENCE PAGE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
DEFAULT
ENG
ENG
ENG
ENGLISH
FRENCH
SPANISH
PORTUGUESE
JAPANESE
KOREAN
RUSSIAN
THAI
PREFERRED MENU LANGUAGE
23
Downloaded from Caradio-Manual.com Manuals
SYSTEM SETUP
4. PASSWORD SETUP PAGE
3.4 PARENTAL
PARENTAL: The parental control function
works in conjunction with the different
censorship classes assigned to DVDs.
These classes help to control the types
of DVDs that the family watches.
There are up to 8 censorship classes for
DVDs.
Note:
The PARENTAL is changeable when 5.1
PASS WORD MODE set to OFF.
After setting the level of parental control.
Please set the password as ON to perform
the lock of changing.
PREFERENCE PAGE
AUDIO
ENG
ENG
SUBTITLE
ENG
DISC MENU
PARENTAL
DEFAULT
1.KID SAF
2.G
3.PG
4.PG 13
5.PG R
6.R
7.NC 17
8.ADULT
4.1 PASSWORD MODE
PASSWORD MODE: Sets the function
operation to be ON for locking the parental
function, and OFF for changing the parental
level.
There will be old password confirmation
when ON/OFF interchange.
The initial password is 136900
PASSWORD SETUP PAGE
PASSWORD MODE
PASSWORD
ON
ON
OFF
PASSWORD MODE
4.2 PASSWORD CHANGE
PASSWORD CHANGE: you can change
the password, please type 6 numerals as
new password.
SET PARENTAL CONTROL
3.5 DEFAULT
PASSWORD SETUP PAGE
DEFAULT: Resets to all the manufacturer's
original settings for this DVD player Press
ENTER to performthe reset.
PASSWORD MODE
PASSWORD
ON
OLD PASSWORD
CHANGE
NEW PASSWORD
CONFIRM PWD
OK
CHANGE PASSWORD
PREFERENCE PAGE
ENG
AUDIO
ENG
SUBTITLE
ENG
DISC MENU
PARENTAL
DEFAULT
*Touching the position where inputting
password, the screen will display the
number button, and user can input the
password by touching number button
RESET
5. EXIT SETUP MENU
LOAD FACTORY SETTING
EXIT SETUP MENU
24
Downloaded from Caradio-Manual.com Manuals
SYSTEM SETUP
SETTING THE TV SCREEN SIZE
Multi-aspect ratio suit to different TV screen size.
Picture format
on Disc
TV Screen Size
4:3
Letter-box
Pan Scan
16:9
Wide Screen
4:3
16:9
Function supported by DVD discs
There are many functions available on DVD discs and the functions vary per player and
per manufacturer.
ALL
Regional code and signal system
Picture proportion modes
Parent lock
DTS surround
Angles for viewing
Number of languages
Closed Caption
Subtitle languages
25
Downloaded from Caradio-Manual.com Manuals
MP3 OPERATION
Note:
* This function can be operated using
the remote control or touch top right
1.Playing a disc, an SD/MMC card or
corner of screen to be functioned.
a USB device containing MP3 files
* If you make a mistake, press CLEAR
Connect a USB device or insert a disc into
the disc slot or SD/MMC card into the card slot. button to clear.
The unit will automatically switch on when
a disc, card or USB device is inserted.
Stop playing
The screen will display as follow:
When playing MP3 files, press button
MP3 OPERATION
Touch this area to display numeric keypad.
MP3
on the remote control STOP button on
the bottom of the screen to stop playback.
02:47 03:40
001/099
PAUSE PLAYING
When playing MP3 files, press BAND/
on the panel or
on the remote control
or PAUSE button on the bottom of the
screen to pause playing and press again
to resume playing.
..
01 LA LUNE
01IN PARADISUM
02 NO ONE LIKE
02 WINTER IN J
02eden
03 SCARBOUGH
PLAY
PAUSE
STOP
PREV
NEXT
SETUP
SKIP FORWARD/BACKWARD PLAY
Press
or
on the remote control
or press and hold
or
on the panel
to performed fast rewind or fast forward.
During MP3 playback, press the
or
button on the remote control or
on the panel or touch on NEXT/PREV
button on the screen to select the next/
previous track.
2
Repeat playing
When playing MP3 files, press the RPT
button repeatedly on the remote control
to select repeat mode: REPEAT ONE,
OFF. While in REPEAT ONE mode,
it will play one track repeatedly. The
defaulted mode is REPEAT ALL mode,
the unit will play all tracks repeatedly.
--4
--8
--16
--32
--
ISO FILE OPERATION
when playing the media with folders,
the unit will play the first track in the
first folder automatically.
Press the
on the remote control
or PREV/NEXT buttons on the screen
to move the cursor to current folder
then press ENTER button on the remote
control to be back to folder list.
Note: The unit will play the tracks in next
folder after playing the previous folder.
The number buttons
Selecting any track directly by using
Number button(0-9).For example, if you
want to play the 23th track, just press
button 2 and then press button 3 and
the corresponding track will be played.
Eject a disc
Press
button on the unit or on the
remote control to eject a disc.
26
Downloaded from Caradio-Manual.com Manuals
NAVIGATION OPERATION
NAVIGATION OPERATION
The GPS system can navigate with
voice, when you do not drive on your
preset line, the system will reset the
line automatically to get the destination.
Press OPEN button on the unit to open
the TFT screen, the SD card slot is on
this position (shown as illustration).
It supports SD card with memorized
navigation map only.
Press
button on the touchable screen
and the screen display as following:
GPS SD card slot
Please use something with needle
end touching on the
button to finish
the calibration.
TILT
MENU
Press SRC button on the unit or on
remote control repeatedly to access the
navigation mode after insert SD card
with stored navigating map.
*Long press SRC/NAV button or Touching
NAV item on source selection screen
also activate the function.
NO TE
Touch the selection displayed on screen
to perform the corresponding operation
For more information regarding the NAV.
Operation, please refer to the user
manual of navigating electronic map.
Please confirm your place is not under
the bridge, on the tunnel or near the
building which can inf ect the signal
received.
For safety, please avoid operate the system
while driving
GPS system is operated in background
at any modes.
Calibration
To avoid the touching effect function
invalid ,plese calibrate the touchable
screen before perform navigating operation
27
Downloaded from Caradio-Manual.com Manuals
INSTALLATION
INSTALLATION
Notes
Before finally installing the unit, connect the wiring temporarily, making sure that
all connections are correct and the unit and the system are properly working.
Use only the parts included with unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions and can void the guarantee.
Consult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the
passenger if there is a sudden stop.
The semiconductor laser will be damaged if it overheats, so don't install the unit in
high temperature environment -- for instance, near a heater outlet.
If installation angle exceeds 30 from horizontal, the unit might not give its optimum
performance.
The cords must not cover up the area shown in the figure below. This is necessary
to allow the amplifires to radiate freely.
Do not cover the area
28
Downloaded from Caradio-Manual.com Manuals
INSTALLATION
INSTALLATION
Install the unit
1.Install the mounting bracket into the
dashboard of the car. And adjust the
mounting bracket to horizontal
2.Fix the mountiong bracket into place
by pressing its tags outwards
3.Slide the main unit slowly inside the
mounting bracket until the tags on either
sides of the bracket lock into the respective holes on the sides of the main unit.
4.Install the removable trim ring
Detach the unit
1.Detach the removable trim ring
2.Insert the keys supplied to the unit at
both sides of the unit (shown as illustrated)
until they click. Pulling the keys makes
it possible to remove the unit from the
dashboard.
Picture 1
Picture 1
Picture 2
Picture 3
Picture 2
Picture 4
29
Downloaded from Caradio-Manual.com Manuals
CABLE CONNECTION
CABLE CONNECTION
1
2
3
4
5
6
7
8
Gray/Yellow Plug
REAR VIDEO OUT 1
Gray/Yellow Plug
REAR VIDEO OUT 2
Blue/Red Plug
DUAL-AUDIO OUT R
9
10
11
12
13
14
Blue/White Plug
DUAL-AUDIO OUT L
15
Black/Red Plug
AUX IN-R
Black/Black Plug
RADIO ANTENNA INPUT
Black/Black Plug
GPS ANT
Brown/Brown Plug
WOOF OUT
1
2 3 4 5 6 7 8
9
10 11 12 13 14 15 16
PARKING BRAKE
REVERSE LIGHT
B
A
Black/White Plug
AUX IN-L
Brown/Yellow Plug
REVERSE VIDEO IN
Black/Yellow Plug
EXOTERIC VIDEO INPUT
Dark gray/White Plug
AUDIO OUT F.L
Dark gray/Red Plug
AUDIO OUT F.R
Shallow gray/White Plug AUDIO OUT R.L
Shallow gray/Red Plug
AUDIO OUT R.R
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Brown
Orange
1
3
5
7
2
4
6
8
1
3
5
7
2
4
6
8
A1.NOTHING
A2.NOTHING
A3.NOTHING
A4.BATTERY
A5.ANTENNA POWER+
A6.LAMP IN
A7.IGNITION KEY
A8.GROUND
B1.SPEAKER REAR R+
B2.SPEAKER REAR RB3.SPEAKER FRONT R+
B4.SPEAKER FRONT RB5.SPEAKER FRONT L+
B6.SPEAKER FRONT LB7.SPEAKER REAR L+
B8.SPEAKER REAR L-
TV SIGNAL INPUT
ACCESSORIES
Mounting Bracket (Half Sleeve) ---------------------------------------------X1
Mounting Screw M5 -------------------------------------------------------------X1
Remote Control ------------------------------------------------------------------X1
Mount Strap----------------------------------------------------------------------- X1
AV cable ---------------------------------------------------------------------------X1
Removable Trim Ring equipped on the unit ------------------------------X1
Rubber ----------------------------------------------------------------------------X1
Release key ----------------------------------------------------------------------X2
Screws ----------------------------------------------------------------------------X 4
GPS antenna ---------------------------------------------------------------------X1
Wire connector ------------------------------------------------------------------X1
Operation manual ---------------------------------------------------------------X1
30
Downloaded from Caradio-Manual.com Manuals
SPECIFICATION
GENERAL
power requirement ----------------------------------------------------------------------- DC/12V(10.8~16V)
grounding system ---------------------------------------------------------------------------------negative type
max: current consumption ---------------------------------------------------------------------------- 15 ADC
max: power output --------------------------------------------------------------------------------------- 4X50W
load impedance ------------------------------------------------------------------------------------ 4
4-8
dimensions--------------------------------------------------------------------------------------178X165X50MM
weight----------------------------------------------------------------------------------------------------------2.6KG
DVD PLAYER
S/N ratio ---------------------------------------------------------------------------------more than 70dB(1kHz)
dynamic range -------------------------------------------------------------------------more than 70dB(1kHz)
distortion ------------------------------------------------------------------------------------------less than 0.2%
video output ------------------------------------------------------------------------------ 1.0Vp--p+0.2V/75
audio output (RCA) -------------------------------------------------------------------- 1.5Vrms+0.3V 10K
FM TUNER
frequency range ----------------------------------------------------------------65.0~74.0/87.5~108.0MHz
usable sensitivity --------------------------------------------------------------------------------------------10dB
S/N ratio ---------------------------------------------------------------------------------------------- 55dB(mono)
distortion ----------------------------------------------------------------------------------------------0.5%(mono)
stereo separation ------------------------------------------------------------------------------ ---- 30dB(1kHz)
MW TUNER
frequency range --------------------------------------------------------------------------------- 522~1620kHz
usable sensitivity ------------------------------------------------------------------------------------------- 30dB
signal-to-noise ratio ---------------------------------------------------------------------------------------- 50dB
31
Downloaded from Caradio-Manual.com Manuals
TROUBLE SHOOTING
TROUBLE SHOOTING
Common problems
Symptom
Cause
Remedy
Power doesn't switch ON .
The unit doesn't operate.
Leads and connectors are
incorrectly connected
Confirm once more that all connections
are correct
A fuse has blown
Fix the problem causing the blown fuse
and replace the old fuse with a new one
of the same capacity
Noise and other factors are
causing the built-in microprocessor to operate incorrectly
Reset the unit
The remote control operation
mode is incorrect
Switch to the correct remote control
mode
Battery power is low
Load new batteries
Some operations are prohibited
with certain discs
Check using another disc
The disc is dirty
Clean the disc
The loaded disc is a type this
unit cannot play
Check what type the disc is
Non compatible video system
disc is loaded
Change to a disc compatible to your
video system
Connections are incorrect.
Check connections
With some discs,96kHz output
is prohibited.
Switch the output setting to 48 Khz
The unit is performing still F.FWD
or F.REV playback
There is no sound during still F.FWD ,
F.REV playback
The operation is prohibited for
the disc
This operation is not possible
The operation is not compatible
with the disc's organization
This operation is not possible
The picture stops (pauses)
and the unit cannot be
operated
Reading of data has become
impossible during playback
After pressing
once more
There's no sound Volume
level is low
The volume level is low
Raise the volume level
There's audio and video
skipping
This unit is not firmly secured
Secure this unit firmly
The picture is stretched the
aspect is incorrect
The aspect setting is incorrect
for the display
Select the appropriate setting for your
display
When the ignition switch is
turned ON (or turned to ACC),
the motor sounds
This unit confirms whether a
disc is loaded or not
This is a normal operation
Operation with the remote
control isn't possible
Playback is not possible.
There's no sound
The prohibited mark
is
displayed and operation is
not possible
32
Downloaded from Caradio-Manual.com Manuals
once start playback
TROUBLE SHOOTING
Problem during DVD playback
Symptom
Cause
Remedy
Playback is not possible
The loaded disc has a different
region number from this unit
Replace the disc with one featuring the
same region number as this unit
Dialog language (and
subtitle language) can not
be switched.
The DVD playing does not
feature multiple language
recordings.
You cannot switch among multiple
languages if they aren't recorded on
the disc
You can only switch between
Switch using the disc menu
options indicated in the disc menu
No subtitles are displayed
The DVD playing does not feature Subtitles are not displayed if they are
subtitles
not recorded on the disc
You can only switch between
Switch using the disc menu
options indicated in the disc menu
Playback is not with the
audio language and subtitle
language settings selected
in SET UP MENU
The DVD playing does not
feature dialog or subtitles in
the language selected in the
SET UP MENU
Switching to a selected language is not
possible if the language selected in the
SET UP MENU is not recorded on the disc
The picture is extremely
unclear/distorted and dark
during playback
The disc features a signal to
prohibit copying (some discs
may have this)
Since this unit is compatible with the copy
guard analog copy protect system. when
playing a disc that has a signal prohibiting
copying the picture may suffer from
horizontal stripes or other imperfections
when viewed on some displays. This does
not mean this unit is malfunctioning.
Problem during Video CD playback
Symptom
Cause
Remedy
The PBC(playback control)
menu display cannot be
called up.
The video CD playing does not
feature PBC
This operation is not possible with video
Cds not featuring PBC
PBC is switched OFF
Switch PBC ON
PBC is switched ON
Switch PBC OFF.
Repeat play and track/time
search are not possible
33
Downloaded from Caradio-Manual.com Manuals