VSP 628PRO-F Quick Start

VSP 628PRO-F
Quick Start Manual
VSP 628PRO-F Quick Start

Any signal input any signal output

LOGO capture and standard test pattern built in

3D signals input and output processing

Support EDID management

Seamless switching between any signals

Support dual 2K output

Preview and program outputs separately

Independently one input to two separately
output conversion

User-defined output resolution

Genlock and reference input

Module based and expendable
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
CONTENT
Product Introduction ...............................................................................................................................2
Hardware Orientation ..............................................................................................................................3
Front Panel .........................................................................................................................................3
Back Panel .........................................................................................................................................4
Operating Instruction ..............................................................................................................................5
Content ...............................................................................................................................................5
How to Realize the System Mode Setting ..................................................................................6
How to Do Customized Output Resolution ...............................................................................11
How to Realize the Test Pattern Setting ...................................................................................12
How to Realize LAN Remote Control Setting ...........................................................................12
How to Realize WEB SERVER Cross-platform Setting ...........................................................15
How to Save the Parameter ......................................................................................................16
How to Load the Saved Parameter...........................................................................................17
WEB SERVER Cross-platform Control Operation Interface .............................................................18
VSP 628PRO Connect APP Control Operation ...................................................................................27
Contact Information...............................................................................................................................32
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
Seite 2
Product Introduction
VSP 628PRO is an advanced high performance
EDID
all-in-one video scaler, scan converter, switcher
interface, seamless switching between the
and transcoder converting any input signal
inputs, VSP 628PRO is one of the most
format to any output signal format.
advanced and flexible signal processor in the
VSP 628PRO supports composite, component,
industry.
VGA,
HDMI,
VSP 628PRO is based on module based
DisplayPort, USB, CVBS and SD/HD/3G-SDI
structure, its standard version comes with all
signal
are
the features you need and expect to find in
provided for the DVI and SDI input and Genlock
old versions. In addition to the standard
signals. With features like LOGO capture and
features, with different modules, you can
standard test pattern built in, 3D processing,
reach more possibility and application range.
DVI
signal
formats.
and
dual
Loop-through
link,
outputs
management,
Web
page
control
System Connection
RGBlink offers solutions to
demanding technical problems.
Any application questions, or
required further information,
please contact with our
customer Support Engineers.
VSP 628PRO System Connection Diagram
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
Seite 3
Hardware Orientation
Front Panel
Button Instruction
MENU
Menu button, push the button
for 3 seconds to lock panel
7
SDI3/VGA2/DVI2/HDMI2/USB1/CVBS1/
DP1.2 signal source button
SCALE
Scale button, push MENU
and SCALE button for 3
seconds to switch language
8
SDI4/VGA3/DVI3/HDMI3/USB2/CVBS2/
HDMI1.4 signal source button
FREEZE
Freeze button
LOGO
LOGO and test pattern setting button
PIP
Single and double images
switch button
DIMMER
Dimmer and effects setting button
SDI1, SDI2
SDI signal source button
TAKE
Seamless effect switch button, and
LOAD reuse button (except in switcher
mode)
DVI
DVI signal source button
0~9
Number button, for parameters setting
HDMI
HDMI signal source button
Knob
Confirm and adjust OLED menus
DP
Displayport signal source
button
OLED
Panel
Show operation menu items
VGA
VGA or YPbPr signal source
button
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
Seite 4
Back Panel
Input Interface
Output Interface
3
Genlock Input BNC port
4
Genlock Loop Out BNC port
5. 7
3G-SDI input BNC port
6. 8
3G-SDI Loop Out BNC port
11
DVI Input DVI-D port
12
DVI Loop Out DVI-D port
13
HDMI Input HDMI-A port
14
HDMI Loop Out HDMI-A port
15
Displayport Input port
17
DVI Output DVI-D port
16
VGA Input DB15 port
18
HDMI Output HDMI-A
19
VGA Output DB15 port
20
CVBS Output BNC port (OC
optional module)
Other Interface
1
10/100M Interface RJ45
2
USB Interface
9
S. V. D. H. U. C.
HDMI_DP_4K2K_IN Optional
Module
10
F. S Optional Module/Sending
card interface
21
Switch
22
Power IEC-3 port
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
Operating Instruction
Content

How to Realize the System Mode Setting

How to Do Customized Output Resolution

How to Realize the Test Pattern Setting

How to Realize LAN Remote Control Setting

How to Realize WEB SERVER Cross-platform Setting

How to Save the Parameter

How to Load the Saved Parameter
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 5
VSP 628PRO-F
Quick Start Manual
How to Realize the System Mode Setting
VSP 628PRO supports 5 kinds of system modes: Standard, Dual 2K, Switcher, Split and MinDelay.
Push the [MENU] button to enter to the menu items, choose <System>, push the knob to confirm. Turn
the knob, choose <System Mode>, user can choose the mode according to actual need.
1. Standard
In this mode, all the outputs are the same image, the same resolution, and support fade in fade out
switch. Each input signal supports scale, effects setting independently.
Single Image Switching
VSP 628PRO can realize seamless effects switching between two channels. Push the signal button,
and the signal will be switched to the output.
For example, the [SDI1] button light is on, it means the signal of output is SDI1, if user need to switch to
VGA signal, push the [VGA] button, and the signal will be seamless cut or fade in fade out to the output.
User can adjust the switch speed in <Trans Time> option in <Transition>by pushing the [MENU] button.
PIP Setting
Enable the PIP function:
VSP 628PRO supports seamless switch in single image and double images. Push the [PIP] button, the
button light is on, and enable the PIP function.
Choose the signal in PIP:
VSP 628PRO can output two same or different signals to the output, the settings are as follows:
1. Push the [PIP] button, and enable the PIP function.
2. Push the [SCALE] or [DIMMER] button, choose <Layer Select>, and push the knob to confirm. (User
can also choose <Layer Select> in <Input> or <Output> option by pushing the [MENU] button.)
3. Turn the knob, and choose main or sub image.
4. Choose the signal, and the selected image will be switched to this signal.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 6
VSP 628PRO-F
Quick Start Manual
Scale Setting
Push the [SCALE] button, and enter to the scale function menus, user can adjust the H size, V size, H/V
size, H pos, V pos and scaling mode by knob or number buttons. If image quality distorts by improper
operation, it can be recover by reset.
Note: In PIP mode, user need to choose the image that to set in <Layer Select> option before setting.
Image Size Adjust
Push the [MENU] button, and enter to the menu items. Turn the knob, and choose <Input>, push the
knob to confirm. Turn the knob, choose <Sizing Adjust>, push the knob to confirm. User can adjust the
H size, V size, H pos V pos, and mask top, bottom, left and right of the image by knob or number
buttons. If image quality distorts by improper operation, it can be recover by reset.
Note: In PIP mode, user need to choose the image that to set in <Layer Select> option before setting.
Dimmer and Effects Setting
Push the [DIMMER] button, and enter to the menu items, user can set the dimmer and effects. The
adjustment value range of dimmer is 0~100.
The setting for effects include brightness, contrast, chroma, hue, color temperature, color correction,
gamma, brightness, H sharpness, V sharpness, noise reduction, Invert, Flip V, Flip H and Flip 90
degree.
Note: User can also choose <Effects> in <Output> option by pushing the [MENU] button for setting.
2. Dual 2K
In this mode, the two channels output independently, CHA outputs to DVI and VGA, CHB outputs to
HDMI, CHA and CHB can input any signal and set different resolutions, but can not support fade in fade
out switch. Each input signal supports scale, effects setting independently.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 7
VSP 628PRO-F
Quick Start Manual
Same operation with standard mode, in this mode, user can switch the signal, set the size and position,
mask the image and adjust the dimmer and effects. User need to choose the channel in <Channel
Select> before setting.
For example, choose the signal of CHB, first, push the [MENU] button to enter to menu items, choose
<Output>, push the knob to confirm, turn the knob, choose <Channel select>, turn the knob to choose
CHB. Then choose the signal, CHB will switch to the selected signal.
3. Switcher
In this mode, the HDMI output is preview image, and the DVI and VGA output is program image,
preview signal can not support fade in fade out switch, and program signal supports.
Same operation with stand mode, in this mode, user can switch the signal, set the size and position,
and mask the image. All the settings above are for preview, push [TAKE] button after setting, and the
preview image will be cut or fade in fade out to the program.
4. Split
In this mode, user can set split simply, and can set the split parameters of single or multiple devices
quickly. The split operations are as follows:
Project: There is one LED display, the size is 3684x1152, divide into right and left halves, the left width
is 1824 and the right width is 1860, we will cascade the two LED displays with one VSP 628PRO, and
display a complete picture in the whole screen.
(1) Connect the interface
Connect the DVI signal to the DVI input interface, connect the DVI output to the left LED sending card,
and connect the HDMI output to the right LED sending card.
(2) Choose the system mode
Push the [MENU] button to enter to the menu items, turn the knob to choose <System>:
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 8
VSP 628PRO-F
Quick Start Manual
Transition
->System
Logo
Display Setup
Seite 9
>>
>>
>>
>>
Push the knob to confirm, turn the knob to choose <System Mode>:
->System Mode
Ethernet
Input EDID
VFD Bright
>>
>>
>>
>>
Push the knob to confirm, turn the knob to choose <Split>:
System Mode
* Split
(3) Choose the split mode
Turn the knob in split menus, and choose the split mode as <One Machine> or <Multi Machine>.
->One Or Multi
One Machine
Choose <One Machine>, push the knob to confirm, turn the knob, choose the split mode, for example,
choose <H One-To-Two>:
One Machine
* H One-To-Two
(4) Set the output format
Push the [MENU] button to enter to the menu items, turn the knob and choose <Output>.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
Input
->Output
Custom Formats
Views
Seite 10
>>
>>
>>
>>
Push the knob to confirm.Turn the knob to choose <Output Format>, and set the output formats as
2048x1152@60hz.
Channel Select
->Output Format
CVBS Format
Out Auto Config (N/A)
CHA
>>
>>
>>
The resolutions of the two outputs will change at the same time.
(5) Set the split parameters
After choose the split mode, the OLED screen will show the split parameters, set the H total as 3864,
set the V total as 1152, set the first width as 1824, then turn the knob, and choose <Set Parameter>,
push the knob to confirm.
->H Total
V Total
First Width
Set Parameter
3864
1152
1824
>>
(6) Save
Push the [MENU] button to enter to the menu items, turn the knob and choose <Views>.
Input
Output
Custom Formats
->Views
>>
>>
>>
>>
Push the knob to confirm. Turn the knob again and choose <Save>.
Recall
->Save
Delete
Delay Recall
>>
>>
>>
>>
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
Push the knob to confirm. Turn the knob to choose the save mode, for example, choose File 4, push the
knob to confirm.
Save
->File 4
File 1 will be auto recalled after device powering on.
5. MinDelay
In this mode, user can achieve the same input and output resolutions, and achieve the least processor
delay time. Except effects function, it can not support scale, De interlacing, etc.
How to Do Customized Output Resolution
Push [MENU] button to enter to the menu items, turn the knob and choose <Custom Formats>, push
the knob and confirm.
1. Enter digits of desired resolution by pressing the red number buttons.
2. After the digital, push the knob will add ×, means before × is the horizontal size. Same operation for
vertical size.
3. After the digital, push the knob will add ×, means before the × is the vertical size, and after the × is
the refresh rate. Only digital 50 or digital 60 supports for the refresh rate. Use the digital buttons to
finish the settings.
4. After input all the values, push the knob to enable VSP 628PRO to output this resolution.
VSP 628PRO will take 5~10 seconds to enable this output resolution.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 11
VSP 628PRO-F
Quick Start Manual
How to Realize the Test Pattern Setting
Push the [LOGO] button, user can set the test pattern, the settings are as follows:
Type: Choose the test pattern type, including LOGO, H RAMP, V RAMP, 100% COL BAR, 75% COL
BAR, 16*16 GRID, 32*32 GRID, BURST, 50% GRAY, GRAY STEP1, GRAY STEP2, WHITE、BLACK
and SMPTE COL BAR.
Raster Box: User can choose enable or disable the raster box function.
Diag Motion: User can choose enable or disable the diag motion function.
AOI Raster Box: User can choose enable or disable the AOI raster box function. If choose “ON”, user
can choose the types including Box X, Box Y, Box Width and Box Height. If image quality distorts by
improper operation, it can be recover by reset.
How to Realize LAN Remote Control Setting
Firstly, To realize LAN remote control need to build up a LAN platform including: ①One computer
(Laptop or computer, used to do remote control which installed windows control software in the
computer).②One router (Better to have wireless function which may realize WEB control cross different
platform; without wireless function is available but only realize cable remote control. No limitation for
router’s model and brand, such as VPN router model: Netcore 255 or 266. Volans VE 760W or 982W).
③One VSP 628PRO processor (as long as the router’s network ports can connect to, user can place
multi pieces of VSP 628PRO).
Step one: LAN physical connection. Connect VSP 628PRO and router with network cable, then connect
computer and router with network cable also, use the LAN port of router, WAN port is used for
connecting to outer net. Sketch map as below:
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 12
VSP 628PRO-F
Quick Start Manual
Step two: IP address setting (processor’s default IP address is 192.168.0.100)
Firstly change computer’s local connection to “automatically getting the IP”, showed as below:
Secondly refer to router’s instruction (user manual, specification), and find out router’s default network
segment.
If router’s default network segment is 192.168.0.1, then it is same to processor IP address segment,
open up windows control software and user can directly control on VSP 628PRO.
If router’s default network segment is 192.168.1.1, then user need to change router’s default gateway
or change processor’s IP, both methods are available, but we suggest to change processor’s IP.
Method one: Change processor’s IP.
Push the [MENU] button on front panel and go into items as below picture shows. Change processor’s
IP to be 192.168.1.100, confirm and restart the processor, then user can directly control on VSP
628PRO via windows control software.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 13
VSP 628PRO-F
Quick Start Manual
Method two: Change router’s gateway.
Type in 192.168.1.1 on the browser and go into router setting.
Type in default account and code (please refer to the router user manual for the information).
Go to router setting part and find out “LAN port setting”, change the default value “192.168.1.1” to be
“192.168.0.1”.
Save the setting and restart the router, then user can directly control on VSP 628PRO via windows
control software.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 14
VSP 628PRO-F
Quick Start Manual
How to Realize WEB SERVER Cross-platform Setting
First, the formation of LAN Remote Control Platform: one Ipad or one Iphone, one router (with wireless
functions, for example with a wireless-enabled VPN router models: Netcore 255 and 266. Volans
VE760W, 982W.), one VSP 628PRO processor (can be more processors, as long as the network
interface can be connected to the router)
The first step: LAN Physical Connection: connect VSP 628PRO and routers by CAT5, and connect
routers by CAT5, please use the LAN Ethernet port, WAN port is only used to connect to external
networks, it’s not allowed to use in this step.
Connection diagram is as below:
The second step: IP address setup. Please refer to IP Setup steps which in the “How to Realize LAN
Remote Control Setting” section. (Make sure that processors IP address and router IP address are in
the same band.)
When users use Ipad or Iphone, you can directly use the Safari browser, enter the URL 192.168.0.100
(default) and run. If user using other types of devices will need to install the kernel webkit browser
such as: Apple Safari, Google Chrome or Maxthon browser. The Installing package will provide
Google Chrome browser (windows version).
Note: The Internet Explorer, Edge and Firefox are not supported.
The third step: Make connections.
Click
ico, run Google Chrome browser, open the page enter 192.168.0.100 (default) and run.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 15
VSP 628PRO-F
Quick Start Manual
After connection successfully, Web page appears as VSP 628PRO system control interface.
Click on the toolbar below the control interface, then accesses setup menu, now WEB control on VSP
628PRO is available.
How to Save the Parameter
VSP 628PRO provides 22 kinds of save modes, the settings are as follows:
1. Push the [MENU] button to enter to the menu items, turn the knob, choose <View>, push the knob to
confirm.
2. Turn the knob, and choose <Save>, push the knob to confirm.
3. Turn the knob, and choose the location that need to save, push the knob to confirm.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 16
VSP 628PRO-F
Quick Start Manual
How to Load the Saved Parameter
VSP 628PRO provides 22 kinds of save modes, the settings are as follows:
1. Push the [MENU] button to enter to the menu items, turn the knob, choose <View>, push the knob to
confirm.
2. Turn the knob, and choose <Recall>, push the knob to confirm.
3. The button on is ready for recall, and button flashes means just recall. Push the button on or turn the
knob to choose the location that need to recall, push the knob to confirm.
Note: User can only recall File 1 to File 10 by pushing the button. Beyond File 10, user need to
choose the file by the knob.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 17
VSP 628PRO-F
Quick Start Manual
WEB SERVER Cross-platform Control Operation Interface
If users use Ipad or Iphone, they can input the website 192.168.0.100 (default) or 192.168.0.231 in
Safari browsers to operate. If users need to modify VSP 628PRO IP address, they can input
corresponding modified IP address.
If users use other device, they need to install webkit kernel browser, such as: apple Safari, Google
Chrome or Maxthon. Installation package provides Google Chrome browser (Windows version). Now
take Google Chrome browser for example, specific steps are as follows:
Step 1: click
to run Google Chrome browser, open the webpage and input 192.168.0.100 to
operate:
Step 2: Enter the default home page, the system provides 13 kinds of output resolutions for choose,
blue stripe means current selected output resolution. Selected, then VSP 628PRO will automatically
update the output resolution.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 18
VSP 628PRO-F
Quick Start Manual
Seite 19
Note
Users can freely switch the icons in title bar to set
relevant functions, following will introduce the
relevant settings.
Step 3: Select "Input" icon in title bar, user can click the signal source that need, VSP 628PRO will
automatically update input signal source.
Step 4: Select "Image" icon in title bar to scale the image, user can modify digital setting parameters
and image size and position easily through "-+" icon. Click "Set" after modify the digital, VSP 628PRO
image will display the latest Settings.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
Seite 20
Step 5: Select "PIP" icon in title bar. When the PIP sliding block icon is grey, then it is single channel
picture mode, and if image selection is gray, then image 1 is default for single image output image, and
can't be chosen.
Note
User can preset the image mode that switch the
current single picture mode to double-picture mode
and the position of the two images in the mode.
Drag the slider rolling ball, when the slide block is green, PIP starts.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
Then user can set PIP location, in addition to system default PIP upper left picture, also can choose
picture above picture and picture edge picture.
In PIP mode, the default image1 is the main image, image 2 for PIP sprite, click the corresponding
image when need to edit image 1 or image 2, the selected image with blue stripes, tick, as shown below:
image 2 is selected, all settings will for image 2. For example, you can switch "Input" icon in title bar to
choose image 2 input source.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 21
VSP 628PRO-F
Quick Start Manual
Seite 22
Note
If image 1 and image 2 with the same input source,
then it will display the same picture in PIP.
Step 6: Image brightness setting, it is mainly for output image setting. If "Sync" is grey, you can adjust
one color alone, when "Sync" is green, it means it starts, drag one color, and the other two color values
will change accordingly to the same value.
Note
User can adjust setting according to actual
condition, the function mainly suitable for the
personage that is very processional in image
quality. Nonprofessional isn’t recommend to the
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
Seite 23
above operations, if distortion of image quality as of
improper operation errors, you can reset to the
factory initialization.
Step 7: Image contrast setting, it is mainly for output image contrast. If "Sync" is grey, you can adjust
one color alone, when "Sync" is green, it means it starts, drag one color, and the other two color values
will change accordingly to the same value.
Note
User can adjust setting according to actual
condition, the function mainly suitable for the
personage that is very processional in image
quality. Nonprofessional isn’t recommend to the
above operations, if distortion of image quality as of
improper operation errors, you can reset to the
factory initialization.
Step 8: Save and Call function. User can save the parameters to UserMode1 and UserMode2, and can
also load UserMode1 and UserMode2 that saved before.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
Step 9: Page setting.
First, choose the language according to user’s need. And the default is automatic identification.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 24
VSP 628PRO-F
Quick Start Manual
Click "Set" after select the language (such as select Chinese), pay attention to system prompt
"Language will effect after the next time and after reboot IP will affect" (at green box); Now you need to
refresh the page to complete the setting.
If need to modify IP address, user can press MENU->SYSTEM ->Ethernet->IP, it will take effect after
restart the device.
Reset: If appear wrong operation, click "Reset" to factory default.
Key Lock: If slide block is gray, it is unlock, and VSP 628PRO keys can normally operate. And if slide
block is green, the VSP 628PRO keys locked, and user can't operate any button.
Dimmer: ALPHA transparency regulation. Drag ball to change the transparency value, transparency
value is between 0 ~ 100 levels.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 25
VSP 628PRO-F
Quick Start Manual
Seite 26
Note
Operation is invalid in PIP mode.
Step 10: Log function is mainly for research and development personnel as debugging use.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
Seite 27
VSP 628PRO Connect APP Control Operation
1. Download the APP
User can log in the Apple or Android system to search and download the video processor client APP,
click the link https://itunes.apple.com/au/app/vsp-628pro-software-control/id990925513?mt=8, and then
install the VSP 628PRO client APP on Iphone or IPAD, shown as
completed, the Iphone or IPAD will show the icon
. After the installation is
.
2. APP Control Interface Introduction
WIFI
Network cable
1. Prepare a router that with wireless internet and DHCP function, connect and set the router by
computer before connect to VSP 628PRO, and enable the IP and DHCP function. (For more details
about setting, please refer to router’s instruction).
2. Connect the LAN port of router to the LAN port of VSP 628PRO with the network cable.
3. Connect to the router by IOS or Android device, system default IP automatic access, use the web
browser to access “192.168.0.100”, the default IP address of VSP 628PRO, if the IP address is
changed, please enter the changed IP address. (Set path: MENU->System->Ethernet->IP), user
can wirelessly control VSP 628PRO after loading.
⑴ Make sure the device is connected to the router, power on, after the device is stable,
turn on the mobile phone or IPAD APP to search and connect the device, as follows:
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
VSP 628PRO-F
Quick Start Manual
⑵ There are 2 device options after connect the device, DEMO is the presentation
template that comes with software, choose any one of them, as follows:
⑶ After connection, it enters to the processor manager interface, as follows:
⑷ Click <Signal Select>, it supports 4 different modes, as follows:
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 28
VSP 628PRO-F
Quick Start Manual
⑸ Click <Save And Load>, it supports 22 kinds of save modes, as follows:
⑹ Click <Image Setting>, user can adjust the parameters in preview mode, as follows:
⑺ Click <Mask And Scale>, user can mask and scale the image, as follows:
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 29
VSP 628PRO-F
Quick Start Manual
⑻ Click <Test Pattern>, there are 13 kinds of test patterns, as follows:
⑼ Click <Parameter Setting>, user can adjust the output resolution, as follows:
⑽ Click <Information>, user can view the device mode, serial number, IP address and
module versions. User can also click “Factory Reset” to reset to its factory settings.
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 30
VSP 628PRO-F
Quick Start Manual
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de
Seite 31
VSP 628PRO-F
Quick Start Manual
Seite 32
Contact Information
Warranty:
All video products are designed and tested to the highest quality standard and backed
by full 3 years parts and labor warranty. Warranties are effective upon delivery
date to customer and are non-transferable. RGBlink warranties are only valid to the
original purchase/owner. Warranty related repairs include parts and labor, but do
not include faults
lighting
resulting
from
user
negligence,
special
modification,
strikes, abuse(drop/crush), and/or other unusual damages.
The customer shall pay shipping charges when unit is returned for repair.
vision tools distributions gmbh | 22041 Hamburg | Königsreihe 12-14
Tel.: +49 (0)40-209 864-0 | www.visiontools.de | mail@visiontools.de
vision tools | 22041 Hamburg | T 040-209864-0 | mail@visiontools.de | www.visiontools.de