Contents
1 Safety Precautions ............................................................................................ 4
2 INTRODUCTION ................................................................................................. 5
3 FEATURES ......................................................................................................... 6
4 Quick Start Guide .............................................................................................. 7
4.1 Front Panel.......................................................................................................................7
4.2 Rear Panel ........................................................................................................................8
4.3 Connections .....................................................................................................................8
4.4 Powering On/Off ............................................................................................................ 11
4.5 Remote Control..............................................................................................................12
4.6 Easy Install .....................................................................................................................14
4.7 SCAN CHANNEL ............................................................................................................16
5 Basic Operations ............................................................................................. 16
5.1 Changing channels........................................................................................................16
5.2 Volume/Mute/Audio .......................................................................................................17
5.3 Setting audio options ....................................................................................................17
5.4 Display Resolution ........................................................................................................17
5.5 Info bar ...........................................................................................................................17
5.6 Sleep timer .....................................................................................................................17
5.7 TV/SAT ............................................................................................................................18
5.8 Pause ..............................................................................................................................18
5.9 Zoom...............................................................................................................................18
5.10 NVOD ............................................................................................................................18
5.11 Teletext..........................................................................................................................18
5.12 Subtitle .........................................................................................................................19
5.13 Quick bar ......................................................................................................................19
5.14 Manage of USB memory .............................................................................................19
5.15 Change Satellite...........................................................................................................20
5.16 Change Favourites group ...........................................................................................20
5.17 Recording.....................................................................................................................20
5.18 Play the recorded file when it recording....................................................................21
5.19 Timeshift.......................................................................................................................21
5.20 Unmount USB Disk......................................................................................................22
5.21 HBBTV ..........................................................................................................................22
6 Channel ............................................................................................................ 22
6.1 TV/Radio list...................................................................................................................22
6.2 Managing Channels.......................................................................................................25
7 EPG................................................................................................................... 28
1
Contents
7.1 Changing Group ............................................................................................................28
7.2 Find channel ..................................................................................................................28
7.3 EPG now/next list ..........................................................................................................28
7.4 Switch EPG between now/next.....................................................................................29
7.5 Schedule list ..................................................................................................................29
7.6 Setting timer...................................................................................................................29
7.7 Adding a new timer........................................................................................................29
7.8 Editing a timer affair ......................................................................................................30
7.9 Deleting timer affairs .....................................................................................................30
8 Installation ....................................................................................................... 30
8.1 Search Satellite Channels (fixed antennal) .................................................................30
8.2 Search Cable Channels (fixed antennal) .....................................................................33
8.3 Search Terrestrial Channels (fixed antennal) ..............................................................34
9 System ............................................................................................................. 34
9.1 Basic Setting..................................................................................................................35
9.2 PVR/HDD Setting ...........................................................................................................39
9.3 Net Setting......................................................................................................................41
9.4 Upgrade ..........................................................................................................................43
10 Conditional Access ....................................................................................... 44
11 Online ............................................................................................................. 44
11.1 Message........................................................................................................................44
11.2 Weather Forecast.........................................................................................................45
11.3 FAQ ...............................................................................................................................46
11.4 User Manual .................................................................................................................46
11.5 E-book...........................................................................................................................47
11.6 Config ...........................................................................................................................48
12 File List........................................................................................................... 49
12.1 Switch File list..............................................................................................................49
12.2 Sort files/Sort folder ....................................................................................................49
12.3 Delete files/Delete folder .............................................................................................49
12.4 Play Record File/Music/Movie.....................................................................................50
12.5 Play Picture ..................................................................................................................50
12.6 Online Subtitle .............................................................................................................50
12.7 Setting Subtitle ............................................................................................................51
13 Plug In ............................................................................................................ 52
13.1 Using the calculating...................................................................................................52
14 Networking..................................................................................................... 52
2
Contents
14.1 Youtube.........................................................................................................................52
14.2 Shoutcast .....................................................................................................................53
14.3 Picasa ...........................................................................................................................55
14.4 RSS ...............................................................................................................................55
14.5 Opera ............................................................................................................................56
14.6 FTP Client .....................................................................................................................56
14.7 Kartina TV.....................................................................................................................59
15 Portal .............................................................................................................. 60
15.1 Setting Language.........................................................................................................60
15.2 Add App ........................................................................................................................60
15.3 Remove App.................................................................................................................61
15.4 Move App......................................................................................................................61
15.5 Run APP .......................................................................................................................61
15.6 Navigation Menu ..........................................................................................................61
16 Trouble Shooting ........................................................................................... 63
17 Specifications ................................................................................................ 64
3
About
1 Safety Precautions
CAUTION:
The lightning flash with
arrowhead symbol, within an
equilateral triangle, is
intended to alert the user to
"dangerous voltage" and to
prevent from a risk of electric
shock.
Warning:
The exclamation point within
an equilateral triangle is
To reduce the risk of electric
intended to
shock, don't open the cabinet.
alert the user to important
Refer servicing to qualified
personnel only.
operating and maintenance
(servicing).
WARNING: Do not use this STB where contact with or immersion in water is a possibility. Do
not use near flower vase, washbowls, kitchen sinks, laundry tubs, swimming pools, etc.
WARNING: Do not put the candle or lamp stand on the cabinet; otherwise, there is the danger
of fire.
WARNING: The unit should be connected to a power supply only of the type described in the
operating instructions or as marked on the unit. If you are not sure of the type of power supply
(for example, 120 or 230 V) to your home, consult your local dealer or local power company.
WARNING: This product install diodes. Do not open the cabinet or touch any parts in the inner
mechanism. Consult your local dealer for technical service if the opening is required.
Note: To ensure proper use of this product, please read this User manual carefully and retain
for further reference.
Note: This product install diodes. Do not open the cabinet to avoid the unit direct exposure to
radiation.
Unit Cleaning: After the unit power is turned off, you can clean the cabinet, panel and remote
control with a soft cloth lightly moistened with a mild detergent solution.
Attachments: Never add any attachments and/or equipment without the manufacturer
consent; as such additions may result in the risk of fire, electric shock, or other personal injury.
Locating: Slots and openings in the cabinet are provided for ventilation to protect it from
overheating. Do not block these openings or allow them to be blocked by placing the STB on a
bed, sofa, or other similar surface, nor should it be placed over a radiator or heat register.
Power-Cord Protection: Place the power-supply cord out of the way, where it will not be
walked on. Please take special attentions to cords at plugs, convenience receptacles, and the
point where they exit from the unit.
4
About
Object and Liquid Entry: Never put objects of any kind into this STB through openings, as
they may touch dangerous voltage points or short-out parts that could result in a fire or electric
shock. Never spill any liquid on the STB.
Note: Moisture may be formed on the lens In the following conditions:
when the unit is suddenly moved from a cold environment or an air-condition room to a
warm place.
immediately after a heater has been turned on.
in a steamy or very humid room.
If the moisture forms inside the unit, it may not operate properly. To correct this problem, turn on
the power and wait about two hours for the moisture to evaporate.
Parts Replacement: When the unit parts need to be replaced, user should make sure the
service technician use the replacement parts specified by the manufacturer or having the same
characteristics as the original part. Unauthorized replacement may put the unit In the risk of fire,
electric shock or other hazards.
Safety Check: After all the maintenances and repairs are done, user is required to request the
service technician to conduct the overall safety check to ensure the machine is In the proper
condition.
2 INTRODUCTION
Thank you for purchasing the HD Receiver.
This HD Receiver is fully compliant with the international DVB standard and thus transmits digital images,
sounds, information guides and teletext directly to your TV through the broadcasting.
Now you can comfortably see and receive digitally transmitted music, news, movie and sports broadcasts
in your office or at your home.
In service search section, both the automatic service search method and the manual search mode are
provided. You can save up to Endless TV and Radio services and work around with the favorite, Lock,
Delete, Move and Sort functions.
The menu is very modern and supports multiple languages. All functions can be carried out using the
remote control and some of the functions can also be carried out using the front panel. The HD Receiver is
easy to use and adaptable for future advances. Please be aware that new software may change the
functions of the HD Receiver.
If you have any difficulties concerning the operation of your HD Receiver, please refer to the relevant
section of this manual, including the ‘Troubleshooting’. This Manual will provide you with useful
information on using the HD Receiver.
5
About
3 FEATURES
MPEG-Fully DVB-S / DVB-S2 HD compliant
DVB-T/DVB-C
Endless channels (TV and Radio) programmable
Multilingual menu text support
Channel list editing
Favourite channel list editing
True-color On-Screen Display (OSD)
Full Picture In Graphic (PIG) function
Electronic Program Guide (EPG) for on screen channel information
Subtitle supported
Teletext supported by software emulation
Parental lock facility by channel and program event
Program and Channel information transfer from receiver to receiver
S/PDIF for digital audio or Dolby digital bit stream output
DiSEqC 1.0, 1.1, 1.2 and USALS
HDMI HD Video/Audio Output
USB 2.0 Host
VFD Display for service information
RTC (Real-Time-Clock)
Time Shift
Video Recording
Recording one channel and Time Shifting another channel (optional)
Conax Embedded Card Reader
FullHD 1080p output via HDMI
AVI, MKV, MPG, TS, WMA, WMV, M2TS, FLV, DAT, ASF, MP3 playback
YouTube, Shoutcast Radio, Picasa, Kartina TV, YouPorn and Portal Compatible
Weather forecast & RSS Reader Functions
Software Upgrade support via USB, RS232 or Internet
Endless possibility with Plug-In support
Message, FAQ and User Manual support
Download files from FTP server
Base on LINUX
6
Basic Operations
4 Quick Start Guide
4.1 Front Panel
Open the hand flap on the front panel.
Hold Smartcard horizontally with the electronic chip facing upwards. Then insert the Smartcard into the
slot.
7
Basic Operations
4.2 Rear Panel
4.3 Connections
This section describes how to connect your product to match your particular devices setup and to gain
optimum signal quality. The product provides various interfaces to connect to the TV, VCR or other
devices. Select the most appropriate depending on the device you have.
Warning: Connect all components before plugging any power cords into the wall outlet.
Always turn off the product, TV and other components before you connect or disconnect any
cables.
Note: If you encounter any problems setting up your product, please contact your local retailer helpline.
8
Basic Operations
4.3.1 Connecting the Antenna
1. Connect one or two satellite coaxial cable from the wall to LNB IN.
2. Connect a cable/terrestrial coaxial cable to AERIAL IN.
Note: Cable and terrestrial can't concurrence.
4.3.2 Connecting the TV
1.
2.
3.
TV with the HDMI connector:
For the best picture quality, connect the product and TV using an HDMI cable.
TV with the SCART connector:
For good picture quality, connect the product and TV using a SCART cable.
TV with the AV connector:
To output video and audio, connect the product and TV using an AV cable.
Note:
1. When using the digital audio system, connect the product and the digital audio system using an
S/PIF cable for audio.
2. Connecting your TV directly to the audio/video output of the product will assure a more vivid
9
Basic Operations
picture and enhance your viewing enjoyment.
4.3.3 Connecting the Network
1.
2.
a.
b.
3.
Connecting to the LAN:
Connect one end of the Ethernet cable to the product and the other end to the LAN router.
Connecting to the Wi-Fi (Wireless LAN):
You can connect the network via the Wi-Fi access point or DSL/cable modem.
Plug in the wireless USB dongle to the USB port.(Separate purchase required)
Set the options for the Wi-Fi.
Network Name (SSID): Select the network name of your Wi-Fi access point from the list.
Security Type (WEP): This product supports WEP 40/128bit ASCII and WEP 40/128bit HEX. The
security type of the Wi-Fi and the product shall be set the same.
Password: When using the security type, you must set the password. Enter the same password in
the Wi-Fi setting menu.
Connecting to the 3G:
Connect the network via the 3G card. Plug in the USB that has 3G card.
Note:
1. Make sure the distance between the Wi-Fi access point and the product is not too far away. This
may lower the quality of service.
2. It is recommended to purchase a wireless USB dongle distributed by RT73, RT8192cu, RT3070,
RT2870, RT2070, RT8712u, ZD1211b, ZD1211. Other products may not function or respond.
3. We recommend the network connection over a direct LAN.
10
Basic Operations
4.4 Powering On/Off
1.
2.
3.
Connect the power cord of the product to a wall outlet.
Turn on the power switch of the rear panel.
Power on/off by pressing the [ POWER] button on the remote control or [ POWER] button on the
front panel.
? Frequently Asked Question
Q: The power of my STB has been turned on and not in Standby mode, but the TV screen
showed nothing:
A: Make sure the TV set has been set to the correct video input (not the TV channels). For example, if
you have connected the unit with the Video1 input of the TV set, the TV set has to be switched to
Video1.
Q: The power of my STB has been turn on and not in Standby mode, but the TV screen showed
nothing except popup window with “No Signal” information.
A: That means the channel, which you select, is no signal. Check connection of signal cable or contact
operator.
11
Basic Operations
4.5 Remote Control
You can power on/off the receiver, operate on screen menu, and
use a variety of hot key function.
POWER
To switch your receiver on from standby or standby to on.
MUTE
Used to enable or disable the audio
NUMERIC KEYS
Used to select channels or enter programming parameters
TV / RADIO
Receiver switches between TV and Radio mode.
(ZOOM)
Press
key select zoom times, from X1 to X16.
(RECALL)
Return to the previous menu or status.
AUDIO
Audio channels setup, to select audio mode; Left, Right , Stereo,
Mono.
TV/SAT
Receiver switches between TV and receive mode.
INFO
To display channel status or various program information.
EPG
Display the Programs guide on screen when available.
MENU
Displays the Main Menu on the screen, or return to the previous
menu or status.
EXIT
Cancel the user selection and return to the viewing mode from a
menu.
OK
To select menu option, or to updated on entry.
◄,►KEY
To adjust volume level, or to move cursor left or right in the menu.
▼,▲KEY
To change channels, or to move cursor up or down in the menu.
P+ / PTo move up the cursor to the next or previous page in the menu or
channel list.
V+ / V-
To adjust volume level.
PORTAL
12
Basic Operations
To display the navigation menu in Opera.
●RECORD
To start the recording.
TXT
Shows teletext or subtitle information of the current channel
supports.
OPTION
Shows NVOD information of the current channel supports.
Blue Button
Into the multi-screen function in full screen.
(FIND)
Use to prompt find channels sort by character.
SLEEP
Press timer key you can setup up the Standby time.
V.FORMAT
Press V.FORMAT button to switch the display mode among "Auto",
"480", "576”,” 720”,” 1080I" and "1080P".
FAV(FAVORITE)
To set receiver to the favorite server mode,
display the favorite channel.
SAT
Display the satellite list at normal picture.
FOLDER
Press this button to enter the Record Manager menu directly.
Time Shift
Press this button to display Time Shift info bar.
Play
To play the MP3, JPEG, or Record files. And to display Time Shift
info bar.
Stop
To stop the Time Shift, recording, or MP3/JPEG player.
PAUSE
Used to select the freeze function.
Press once to freeze the screen picture.
/
(PAGE- / PAGE+)
To start Fast Backward / Forward function.
/
Switch to previous / next file when play more files
USB
To remove the USB Hard Disk safely.
/
(PREV / NEXT)
Jump to beginning / end of the file in play mode
PLAYMODE
switch playing mode to order, single cycle and circulation list.
13
Basic Operations
F1
To display quickbar menu in full screen.
F2/F3
Reserved buttons.
4.6 Easy Install
This menu to help you set basic function quickly.
When the STB is first used, there will show the
Easy Install menu.
When you used the Factory Reset function in
System/Basic Setting/Factory Default menu, it
also will show the Easy Install menu after
reboot.
Note: If the software has default channel list, the STB
will play the first channel in the list.
4.6.1 Language Setting
Language setting allows you to select the main
language.
Select the appropriate language with the [▲, ▼] and
[◄, ►] buttons.
In this menu:
Press [P+] button to save it and go to the time Setting
menu.
Time setting allows you to set the system's time. It
will display on front panel with LCD, and info bar.
In this menu:
Press [P+] button to go to the Network Setting
menu.
Press [P -] button to go to the Language Setting
menu.
1. Auto update: Press [ok] button, then press [▲,
▼]
buttons, at last press [ok] button Or [◄, ►] buttons
select an option.
a. ON: Get the time from the channel info that you
will watch.
Note: Now the date and time does not edit.
b. OFF: You need manual set the date and time.
Note: Now you can't edit the GMT offset option.
2. YY/MM/DD: Press number key to set the date.
3. Time: Press number key to set the time.
4. GMT Offset: Press [ok] button, then press [▲,
▼] buttons, at last press [ok] button. Or [◄, ►]
buttons to select appropriate option.
4.6.2 Time Setting
14
Networking
Video setting allow you setting for display format and
resolution.
1. TV Standard: Press [◄, ►] buttons to switch
video resolution circularly by the sequence
“480<-> 576<-> 720<-> 1080i<->1080p<-> Auto”.
Or press [ok] button, and select it with [▲, ▼]
buttons, then press [ok] button to confirm.
Note:
1) Auto means system will set the video output
resolution according to the program, it’s playing,
different resolution programs switching perhaps
will makes TV screen flickering.
2) When you connect with A/V or SCART, the
TV has output that only you change to resolution
the TV supports.
2. Screen ratio: Press [◄, ►] button to switch
video resolution circularly by the sequence
“ 4:3<-> 16:9<-> Auto. Or press [ok] button, and
select it with [▲, ▼] buttons, then press [ok]
button to confirm.
4:3:
Auto - Letterbox - Centre
16:9:
Auto - Pillar Box - Zoom
Auto: The display format follow the channel
details
3. Conversion: Press [◄, ►] buttons to switch the
manner
circularly
by
the
sequence
“
LETTER_BOX<->
PAN_SCAN<->
COMBINED<-> IGNORE. Or press [ok] button,
and select it with [▲, ▼] buttons, then press [ok]
button to confirm.
In this menu:
Press [P+] button to go to the Network Setting
menu.
Press [P -] button to go to the Password Setting
5. Summer Time: Press [ok] button, then press [▲,
▼] buttons, at last press [ok] button Or [◄,
►]buttons to select ON or OFF.
4.6.3 Network Setting
Network Setting allow you setting for connect
internet.
If you connect the LAN and it has DHCP service. At
DHCP option, press [ok] button, then press [▲, ▼]
buttons, at last press [ok] button. Or press [◄, ►]
buttons to select ON . If not DHCP service, you need
select OFF, you need config the network by manual.
In this menu:
Press [P+] button to go to the Video Setting menu.
Press [P-] button to go to the Time Setting menu.
4.6.4 Video Setting
15
Networking
menu.
4.7 SCAN CHANNEL
4.6.5 Password Setting
Go to menu/Install/Satellite Install/Satellite, select
an appropriate satellite and then press [red] button to
scan channels.
Note: If don't scan channels, please contact the local
satellite antenna supply.
Password Setting Change the system password, the
default password is 0000.
In this menu:
Press [P+] button to go to the config Setting menu.
Press [P -] button to go to the video Setting menu.
4.6.6 Config Setting
5 Basic Operations
config Setting allow you config sth about online.
Message auto play: Press [◄, ►] buttons to switch
it between Enable and Disable.
Enable : Allow the message auto play in full screen
when it play video.
Disable: The message can't auto play in full screen
when it play video.
Software Upgrade Notify: Press[◄, ►] buttons to
switch it between Enable and Disable.
Resource Transfer Mode: Press [◄, ►] buttons to
switch it between HTTP and FTP.
5.1 Changing channels
You can change the channels in several ways.
Press the [▲, ▼] buttons in the full screen.
Enter the channel number directly with number
buttons.
Go to the TV List or Organizing Channel and
select a channel.
Note:
Press the [TV/RADIO] button to switch between
TV and radio channels.
Press the [RECALL] button to return to the
previous ten channels.
16
Networking
supports.
5.5 Info bar
The info bar is display informations about the channel
of the time whenever you change channels. Press
the [INFO] button while it hide. Press the [EXIT]
button to hide.
Note: It not displayed when not channels.
5.2 Volume/Mute/Audio
To adjust the audio volume, press the [◄, ►] or [V+,
V-] buttons.
To mute the audio temporarily, press the [MUTE]
button.
: This icon highlight, the channel has EPG.
5.3 Setting audio options
: This icon highlight, the channel has multilingual
: This icon highlight, the channel has Teletext.
Audio options are available only when the
programme supports multiple audio languages.
Press the [AUDIO] button to change the audio
language and direction.
Each time you press the [◄, ►] buttons, the value
changes.
Note: The mute function remains set while you
change channels.
in audio.
: This icon highlight, the channel has subtitle.
: This icon highlight, the channel is Scrambled.
: This icon highlight, the channel is HBBTV.
: This icon highlight, the channel is added
favourite channel.
: This icon highlight, the channel is HD.
5.6 Sleep timer
Press the [SLEEP] button to set the automatic turn
off time.
Each time you press this button, the value changes.
OFF - 120 - 90 - 60 - 30 - 20 - 10 minutes
5.4 Display Resolution
Press the [V.Format] button to set the resolution of
the screen.
Each time you press this button, the value changes.
480<-> 576<-> 720<-> 1080i<->1080p<-> Auto
Note: When you connect with A/V or SCART, the TV
has output that only you change to resolution the TV
17
Networking
5.7 TV/SAT
5.10 NVOD
Press [TV/SAT] key can switch between TV mode
and STB mode
Press [OPTION] button in full screen, it display
NVOD menu if it has NVOD. Or it will show "no option
channel".
5.8 Pause
1.
2.
In playing mode, press [ PAUSE] button, the
picture will be paused, but the sound of the
channel will still continues.
Press [PLAY] button, the screen’s picture will
skip over to the current playing picture, and the
sound of the channel will corresponding playing.
5.11 Teletext
Teletext is a free service broadcast which gives the
latest information on news, weather and many other
topics. You can use interactive services in teletext
mode.
All teletext supporting channels have the TTX icon
display highlight on the info bar.
1. Press [TTX] button and select TTX.
2. Press [▲, ▼] button to select the language.
3. Press [ok] button.
4. Using[◄, ►] & [▲, ▼]buttons to switch
information.
5.9 Zoom
The [ZOOM] button allows you to magnify a certain
area on the images.
Each time you press this button, the enlarge value
changes.
x1, x4, x9, x16
Using[◄, ►] & [▲, ▼] buttons to move the image
center area you want to see. And press [EXIT] button
to exit.
18
Networking
5.13 Quick bar
Press [F1] button to display the menu. It show
weather message, time and state of NET and USB,
and has shortcut to enter to "weather" menu. It also
has message box and manage of USB memory.
Message box is show the system message, like
notify of the new software.
5.12 Subtitle
All subtitle supporting channels have the subtitle
icon display highlight on the info bar.
1. Press [TTX] button and select subtitle.
2. Press [▲, ▼] button to select the language.
3. Press [ok] button.
5.14 Manage of USB memory
1.
Press [yellow] button to Add New Folder, Copy,
Cut, Paste, Rename and Delete functions
2. Press [blue] button to sort the files or folders by
Name, Size or Time.
19
Networking
5.17 Recording
In full screen:
1. Press [REC] button to start recording.
2. Press [REC] button again to pause recording.
3. Press [PLAY MODED] button to enter into
Record menu.
4. Press [▲, ▼] buttons to select an option.
5. Press [ok] button to enter into Record Edit
menu.
6. Press [◄, ►] buttons to change the duration.
7. Press [STOP] button to stop recording.
Note:
1. Now it support two recordings.
2. You can record radio programmes also.
3. The record banner will be display whenever
pressing [INFO] button.
4. You also can change the recording duration in
menu > System > PVR/HDD Setting > Record
setting > Duration.
5. When a new scheduled recording starts while a
recording is already in progress, the record
banner will be displayed for a few seconds to
information that the recording has been started.
If you are watching the channel being recorded,
a record notice will pop – up 6 seconds before
the scheduled recording starts, and the channel
will switch to the scheduled programme
automatically at the start time.
6. Press the [POWER] button while recording will
not stop the recording, a information displayed
for record will stop after 6 seconds before and
standby. If you select NO it will don’t standby and
still recording.
7. Ensure that there is enough free space before
recording. If the free space on the hard disk drive
is insufficient, recording will stop. Recording one
hour of programme may require up to 2 or 3 GB
of hard disk space. The space for recording a 1
hour programme may differ depending on the
preogramme.
8. To view the recorded programme list, go to
menu > File list > Record menu.
5.15 Change Satellite
1.
2.
3.
Press [SAT] button.
Press [▲, ▼] buttons to select Satellite.
Press [ok] button.
5.16 Change Favourites
group
1.
2.
3.
Press [FAV] button.
Press [◄, ►] buttons to select one favourites
group.
Press [▲, ▼] buttons to select channel.
20
Networking
5.18 Play the recorded file
when it recording
1.
Press [PLAY] button to start play the recorded
file.
2. Press [PAUSE] button to pause play.
3. Press [◄, ►] buttons to jump the playing place.
4. Press [PAGE-, PAGE+] button to play fast.
5. Press [PREV/NEXT] button to jump the
head/end of the file.
6. Press [STOP] button to stop play.
5.19 Timeshift
Timeshift is a aptotic big recording. When is full, it will
lost the head file to still recording. When Timeshift is
enable :
1. Press [PLAY] button to play the file.
2. Press [PAUSE] button to pause play.
3. Press [◄, ►] buttons to jump the playing place.
4. Press [PAGE-, PAGE+] buttons to play fast.
5. Press [PREV/NEXT] button to jump the
head/end of the file.
6. Press [STOP] button to stop play.
Note: If you change channel, the path or the time, it
will restart.
21
Networking
5.20 Unmount USB Disk
1.
2.
3.
4.
Press [PLAY MODE] button.
Press [▲, ▼] buttons to select the disk.
Press [ok] button.
Select YES and press [ok] button
6 Channel
6.1 TV/Radio list
The channel list will help you find the channel you
want to watch or edit quickly and easily.
You can access the channel list in several ways.
In full screen, press [ok] button the list will show
in mid.
5.21 HBBTV
When info bar has
icon, it mean this channel
Note: Can only operate for one channel.
has HBBTV service. First make sure the service is
ON in System/Basic Setting/Miscellaneous
Setting/HBBTV menu. In these channels, when the
message display, press [red] button to enter into the
correlative internet point
6.1.1 Changing Channels
Select the channel you want to watch and press the
[ok] button. The displayed channel will change.
1.
: Locked channel,
: Scrambled channel
(CAS icons)
2. Press the [ok] or [Exit] button to exit.
3. Press [TV/Radio] button to switch between TV
and Radio list.
4. Press [P+/P-] button to skip to the next page.
22
Networking
6.1.2 Changing group
6.1.4 Sorting channels
You can display the list of the selected channel group.
Sort the list by:
Number, A-Z, Free+CAS, CAS+Free, TP
1. Press [blue] button.
2. Press [▲, ▼] buttons to select an option.
3. Press [ok] button.
( All, FAV, Satellite, A-Z, Provider, CAS, HD,
Broadcaster.)
1.
2.
Press [▲, ▼] buttons.
Select a channel group.
6.1.5 Watch EPG
1.
2.
6.1.3 Display channel detail
Press [green] button to display the EPG now.
Press [ok] or [EXIT] button to exit.
information
You can display the information menu to know the
information,service, satellite, TP, vid/aud pid,
Pcr/pmt pid, service id, Frame Status,
Provider ,CAS about the channel.
1. Press [▲, ▼] buttons.
2. Select a channel.
3. Press [INFO] button. And press again to cancel.
6.1.6 Adding favourite channel
1.
23
Press [yellow] button.
Networking
to save and exit.
Delete: Press [ok] button, and Press [ok]
to save and exit.
Rename:
Press [ok] button and enter
the name in the keyword, then press [red] to
save and exit.
Note: Cancel lock need input password.(If you not
change the password is 0000)
2. Select FAV and press [ok] button.
3. Select FAV groups that you want.
4. Press [EXIT] to save and exit.
Note: Do it again to cancel the favourite channel
6.1.7 Skipped channel/Cancel skip
channel
You can't watch this channels with [▲, ▼] button in
full screen.
1. Press [yellow] button.
2. Press [▲, ▼] buttons select skip.
3. Press [ok] button.
4. Press [►] button.
5. Press [▲, ▼] buttons.
6. Select YES and Press [ok] button to set the
highlight channel.
7. Select NO and Press [ok] button to cancel set
the highlight channel.
6.1.9 Find channel
6.1.8 Locking/Deleting/Renaming
1.
2.
Find channel in currently group.
1. Press [FIND] button.
2. Input channel name to keyword.
3. Press [red] to confirm.
Press [yellow] button.
Select an option.
Lock: Select ON or OFF, and Press [ok]
24
Networking
Note:
1. Press [green] button to move cursor preceding.
2. Press [yellow] button to move cursor next.
3. Press [blue] button to clear the keyword.
6.2.1.1 Changing group
You can display the list of the selected channel
group.
All, FAV, Satellite, A-Z, Provider, CAS, HD,
Broadcaster.
1. Press [red] button.
2. Press [▲, ▼] buttons, select a channel group.
3. Press [ok] button.
6.2 Managing Channels
6.2.1 Organizing Channel
6.2.1.2 Selecting channel
You can using [ok] button to select one by one, or
select channel quickly by option menu,
Select All, Unselect All, Select Others, Select
TP, Provider
1. Press [green] button.
2. Press [▲, ▼] buttons, select a channel group.
3. Press [ok] button.
Go to MENU/Channel/Organizing Channel menu
will help you to manage the channels.
Note:
1. Press [TV/Radio] button to switch between TV
and Radio list.
2. Press [P+/P-] button to skip to the next page.
25
Networking
6.2.1.3 Moving channel
You can move the order that you select channels.
1. Press [►] button.
2. Select Move and press [ok] button.
3. Press [▲, ▼] buttons to move.
4. Press [ok] button.
6.2.1.5 Display channel detail information
You can display the information menu to know the
information,
service, satellite, TP, vid/aud pid, Pcr/pmt pid,
service id, Frame Status, Provider CAS about the
channel.
1. Press [▲, ▼] buttons to select a channel.
2. Press [INFO] button. And press again to cancel.
6.2.1.4 Locking/Deleting/Renaming/Skiping
1. Press [►] button.
2. Select an option.
Lock:
Press [ok] to save and exit.
Delete:
Press [ok] button.
Rename:
Press [ok] button and
enter the name in the keyword, then press [red] to
save and exit.
Skiping:
Press [ok] button.
6.2.1.6 Find channel
Find channel in currently group.
1. Press [FIND] button.
2. Input channel name to keyword.
3. Press [red] to confirm.
Note:
26
Networking
1.
2.
3.
4.
Press [green] button to move cursor preceding.
Press [yellow] button to move cursor next.
Press [blue] button to clear the keyword.
Press [white] button to switch the input mode.
1. Select channels with [ok] or option
2. Press [►] / [◄] button.
3. Select Add FAV/Remove.
4. Press [ok] button.
Note:
1. When you cancel favourite channels, you can
only using [ok] to select.
2. All favourite channels in the right column.
6.2.2.2 Renaming for FAV group
1. Press [►] or [◄] button.
2. Select Rename.
3. Press [ok] button to input the name in keyword.
4. Press [red] button.
Note:
1. Press [green] button to move cursor preceding.
2. Press [yellow] button to move cursor next.
3. Press [blue] button to clear the keyword.
6.2.2 Organizing Favourites
Go to MENU/Channel/Organizing Favourites menu
to add favourites channel to the favourite group.
Note:
1. Press [TV/Radio] button to switch between TV
and Radio list.
2. Press [P+/P-] button to skip to the next page.
6.2.2.1
Adding
favourite
favourite channels
6.2.2.3 Moving favourite channels
1. Press [◄] button.
2. Select Move and Press [ok] button.
3. Press [▲, ▼] buttons.
4. Press [ok] button.
6.2.2.4 Changing favourite group
channels/Cancel
27
Networking
1.
2.
3.
2.
3.
Press [FAV] button.
Press [▲, ▼] buttons to select a group.
Press [ok] button.
Select a channel group.
Press [ok] button.
7.2 Find channel
7 EPG
Find channel in currently group.
1. Press [FIND] button.
2. Input channel name to keyword.
3. Press [red] to confirm.
Note:
1. Press [green] button to move cursor preceding.
2. Press [yellow] button to move cursor next.
3. Press [blue] button to clear the keyword.
4. Press [white] button to switch the input mode.
The EPG(Electronic Programme Guide) displays
the detailed programme information of each channel,
in time and date order. You can customize your own
programme guide to list the channels or programmes
of interest to you and schedule your viewing using the
programme information.
Note:
1. Press [INFO] button to view detailed information
of the chosen programme.
2. Press [P+/P-] button to skip to the next page.
3. Press [TV/Radio] button to switch between TV
and Radio list.
7.3 EPG now/next list
The list show now/next EPG for the current channel.
7.1 Changing Group
You can display the list of the selected channel
group.
All, FAV, Satellite, A-Z, Provider, CAS, HD.
1. Press [red] button ant then press [▲, ▼]
buttons.
28
Networking
Go to menu/channel menu, then select Organizing
Timer or in EPG menu press [yellow] button.
7.4 Switch EPG between
now/next
7.7 Adding a new timer
There are two ways to switch EPG now and next list.
Press [◄, ►] buttons to switch the list EPG
between now and next.
1. Press [green] button.
2. Select EPG Now or EPG Next with [▲,
▼] buttons.
3. Press [ok] button.
1.
2.
3.
4.
Press [yellow] button to go to Timer menu.
Set options
Press [red] button to rename for the affair.
Press [EXIT] and select YES to save and exit.
7.5 Schedule list
The schedule list show a week EPG for the current
channel.
1. Press [green] button, and press [▲, ▼] buttons
to select EPG Schedule, at last press [ok] button.
2. Press [◄, ►] buttons to switch date.
3. Press [▲, ▼] buttons to switch the EPG affair.
4. Press [blue] button to change channel.
Note:
1. You can't set the affair time before system time.
2. You also press [REC] button to add timer affair
about the EPG in EPG Now/Next/Schedule menu.
3. You can't add timer affair more then eight.
Subjoin:
1. Number: Display the order of current item.
2. Service : Show the channel, if you want change,
press [ok] key.
3. Event name: Show event default name, you also
press [red] key to rename it.
4. Start date: Show start date of event, you can
press number keys to change it.
5. Start time: Show start time of event, you can
press number keys to change it.
6. End date: Show end date of event, you can
7.6 Setting timer
There are two ways to go to the timer menu.
29
Networking
7.
8.
9.
press number keys to change it.
Stop time: Show end time of event, you can
press number keys to change it.
Repeat: Show the event transact times, press
[◄, ►] keys to switch among once, everyday, a
week, workday, weekend.
Timer mode: Type of the event, it has change
service and HDD record.
7.8 Editing a timer affair
1.
2.
3.
4.
You can either connect to two antenna with a single
LNB switch using an RF cable.
Press [green] button to go to Timer menu.
Set options
Press [red] button to rename for the affair.
Press [EXIT] and select YES to save and exit.
7.9 Deleting timer affairs
1.
2.
Press [ok] button to select one or more.
Press [red] button to delete.
8 Installation
Installation menu allows you to configure your
antenna and search the available TV and radio
channels. You can configure the fixed antenna, SCD
antenna or motor antenna with this receiver.
8.1.2 DiSEqC
You can either connect to several antennas with a
LNB switch using RF cable.
8.1 Search Satellite
Channels (fixed antennal)
Go to menu/Install/Satellite Install, you can search
channels by selecting the switch type and setting the
required satellite.
Note: If the antenna is not properly set, channel
search cannot be activated which means you cannot
watch any of the programmes on air.
8.1.1 LNB Only
You can either connect to an antenna with a single
LNB switch using an RF cable.
30
Networking
Mode:
1. All: Scan all type channels it can find.
2. FTA: Scan free channels.
3. ALL_TV: Scan all TV channels.
4. FTA_TV: Scan free TV channels.
5. ALL_RADIO: Scan all radio.
6. FTA_ RADIO: Scan free radio.
Net: Select NIT ON to receive the latest
transponder information.
4. Press [ok] button to scan.
5. When the search has completed, select save
and press [ok] button to save the found
channels and exit.
Note: Press [EXIT] button to stop the channel
search.
8.1.3 Using LNB Switch Only
You can search only channels of one or two satellite
using the fixed antenna.
1. Check that your antenna connection and the
selected antenna type are correct.
2. Select a satellite figure and press the [green]
button.
Satellite: Select the satellite.
Tuner Select: Choose Tuner 1 or Tuner 2
Connection Type: Choose Separated or
Loop Through.
Note: Only choose Tuner 2, this item can
edit.
LNB: Select the LNB frequency.
22kHZ: Select On when using a 22kHZ tone
switch box.
DiSEqC: Select the DiSEqC switch,
Power: Select the becoming value.
3.
8.1.4 Blind Scan channels
This function is scan channels but don't need manual
add TP in transponder list. First, it automatic add
transponders that has single, then scan channels
belong those transponders.
1. Go to satellite list.
2. Press [▲, ▼] buttons to select one satellite.
3. Press [red] button.
4. Press [◄, ►] buttons to select ON.
5. Press [◄, ►] buttons to select Mode among All,
FTA, aLL TV, FTA_TV, ALL_RADIO and
FTA_RADIO.
All: Scan all type channels it can find.
FTA: Scan free channels.
ALL_TV: Scan all TV channels.
FTA_TV: Scan free TV channels.
ALL_RADIO: Scan all radio.
FTA_ RADIO: Scan free radio.
Press [red] button.
31
Networking
6. Press [◄, ►] buttons to select Net between NIT
OFF and NIT ON.
NIT ON: To receive the latest transponder
information.
7. Press [◄, ►] buttons to select Polarization
among Auto, H and V.
Auto: Scan channels that the polarization is
H and V.
H: Scan channels that the polarization is H.
V: Scan channels that the polarization is V.
8. Press [ok] button to scan.
3.
4.
5.
Sym: Enter the symbol rate of the
transponder.
FEC: Select the FEC for the transponder.
Each time you press [◄, ►] buttons, the
value changes.
Auto <–> 1/2 <-> 2/3 <-> 3/4 <-> 4/5 <-> 5/6
<-> 6/7<-> 7/8 <-> 8/9 <->1/4 <-> 1/3 <->
2/5 <-> 3/5 <-> 9/10.
Mode: Select the mode with DVB-S or
DVB-S2.
Press [ok] button.
Press [yellow] button to edit the select
transponder.
Press [blue] button to delete the select
transponders.
Press [INFO] button to display the search
channels of the transponder.
8.1.6
Search
Channels
(Motor
Antenna)
You can set the position of the satellites when using a
motor antenna for efficient channel search.
1. Check that your antenna connection and the
selected antenna type are correct.
2. Select the satellites that the motor antenna is
pointing to.
3. Set the type and location of your motor. (Motor
Setting)
4. Set your antenna position for the selected
satellites.
5. Set the operation limit of your motor.
6. Press [red] button to scan, the found channels
will be listed.
8.1.5 Settin Transponder
The available transponder for each satellite is
automatically listed. You can enter the transponder
setting options directly if necessary.
1. Press [yellow] button to go to the Transponder
list.
2. Press [green] button to add a new transponder.
Freq: Enter the frequency of the
transponder.
H/V: Select the polarization of the
transponder with H or V.
32
Networking
7.
When the search has completed, select save
and press [ok] button to save and exit.
Note:
1. Only channels of one satellite can be searched
when using a motor antenna. Please repeat the
search process to search more satellites.
2. Press [EXIT] button to stop and press [ok]
button to save and exit.
3. Refer to Setting Transponder for details in
transponder setting.
8.1.7 Motor setting
8.2 Search Cable Channels
Set the type and location of your motor.
1. In Menu/Install/Satellite/Edit Satellite menu,
press [yellow] button.
2. Select motor type at motor item.
DiSEqC 1.2: General motor antenna using
DiSEqC 1.2.
USALS: Motor antenna using USALS.
3. Select My Longitude and enter the longitude
and direction.
4. Select My Latitude and enter the latitude and
direction.
5. Select Set Limit and set the limit for the Motor.
Select the value is east or west
Select the Move Step or Move Continue to
move the Motor to east or west.
Select the save and press [ok] button to
save it.
Note: When Motor Type is set as DiSEqC 1.2, the
menu is not My Longitude, My Latitude.
(fixed antennal)
Go to menu/Install/Cable Install, you can search
channels by manual or auto.
Note: If the antenna is not properly set, channel
search cannot be activated which means you cannot
watch any of the programmes.
In manual installation:
1. You can press [ok] button to select one or more
TP and press [red] button to scan channels.
2. Press [green] button to add a new transponder.
Freq: Enter the frequency of the
transponder between 70000 and 900000.
Sym: Enter the symbol rate of the
transponderbeween 1000 and 45000.
QAM: Select a QAM for the transponder.
Each time you press [◄, ►] buttons, the value
changes.
16 <–> 32 <-> 64 <-> 128 <-> 256 . Press [ok] button
to confirm.
33
Networking
Band Width: Press [◄, ►] buttons to select
a value among 6 MHz, 7 MHz and 8 MHz.
Channel No: Input channel number
between 0 and 200.
Press [ok] button to confirm.
8. Press [yellow] button to edit the select
transponder.
9. Press [blue] button to delete the select
transponders.
10. Press [INFO] button to display the search
channels of the transponder.
3. Press [yellow] button to edit the select
transponder.
4. Press [blue] button to delete the select
transponders.
5. Press [INFO] button to display the search
channels of the transponder.
In auto installation:
Press [ok] button to enter and it auto scanning
channels.
8.3 Search Terrestrial
In auto installation:
Press [ok] button to enter and it auto scanning
channels.
Channels (fixed antennal)
Go to menu/Install/Terrestrial Install, you can
search channels by manual or auto.
Note:
1. If the antenna is not properly set, channel search
cannot be activated which means you cannot watch
any
of the programmes.
2. Cable install menu and terrestrial install menu
can't display at the same time.
9 System
Go to menu/system, you can view the information of
the system, Basic Setting, PVR/HDD Setting, Net
Setting, Upgrade.
Note: Press [EXIT] button to exit.
First:
In config menu:
Press [◄, ►] buttons to select a properly region
among Australia, German and UK.
In manual installation:
6. You can press [ok] button to select one or more
TP and press [red] button to scan channels.
7. Press [green] button to add a new transponder.
Freq: Enter the frequency of the
transponder between 50000 and 900000.
34
Networking
[ok] button. Or [◄, ►] buttons select EPG
9.1 Basic Setting
language.
Go to Menu/System/ Basic Setting, in this menu,
there has Language Setting, Time Setting,
Parental Control, A/V Output, Factory Default,
Miscellaneous Setting, Tuner Configuration,
Conditional
Access,
Contact,
System
Information.
5.
Subtitle Language: Press [ok] button, then
press [▲, ▼] buttons to select on option, at last
press [ok] button. Or [◄, ►] buttons select the
subtitle language. It is an item for changing the
language of the Subtitle. As long as the services
support it, the Subtitle language is changeable
by subtitle menu on full screen. The supported
9.1.1 Setting language
1.
language can be changed without any notice.
Menu Language: Press [ok] button, then press
6.
[▲, ▼] buttons to select on option, at last press
press [▲, ▼] buttons to select on option, at last
[ok] button. Or [◄, ►] buttons select an OSD
press [ok] button. Or [◄, ►] buttons select the
menu language.
2.
TXT language. As long as the services support it,
Audio Language: Press [ok] button, then press
the Teletext language is changeable by teletext
[▲, ▼] buttons to select on option, at last press
menu on full screen. The supported language
[ok] button. Or [◄, ►] buttons select an audio
can be changed without any notice.
language.
7.
Note: Some channels have more than one audio
[ok] button. Or [◄, ►] buttons select Auto or
set the first audio for this channel. If the playing
Manual.
channel has the same audio as the “First Audio”
Auto: it will automatically display subtitle in has
you set, system will play this audio language as
subtitle stream,
default. If the channel hasn’t the suited audio
Manual: It need press [yellow] key and select
language, then the default language of current
subtitle to display.
channel will be played automatically. The
8.
selections of audio languages include: English,
Online Language: Press [ok] button, then press
[▲, ▼] buttons to select on option, at last press
French, German, Russian, Arabic, Portuguese,
[ok] button. Or [◄, ►] buttons select online
Turkish, Spanish, Polish, Italian and so on.
menu language.
Audio Priority: Press [ok] button, then press
Note: the Weather Forecast, FAQ, User
[▲, ▼] buttons to select on option, at last press
Manual language will change with the option.
[ok] button. Or [◄, ►] buttons select Dolby
Digital or Language.
Dolby Digital: Dolby audio track will be played if
the current channel has dolby audio track.
Language: Don’t priority play dolby audio track
at the channel that has dolby audio track.
4.
Subtitle display: Press [ok] button, then press
[▲, ▼] button to select on option, at last press
language for choosing, by this function you can
3.
Teletext Language: Press [ok] button, then
EPG Language: Press [ok] button, then press
[▲, ▼] buttons to select on option, at last press
35
Networking
9.1.2 Time Setting
9.1.3 Parental Control
1.
In this menu, you can set a password for anyone who
wishes to operate the STB. And you can also set the
password for the lock channels. (How to set the lock
channel please refer to LOCK) Here will show you
how to setting and how to revising the password.
1. Parental Lock: Press [ok] button, then press [▲,
▼] buttons to select on option, at last press [ok]
button. Or press [◄, ►] buttons to select ON or
OFF.
ON: You must input the password to enter into
menu
OFF: Not need password to enter into menu.
2. Censorship Classification: Press [ok] button,
then press [▲, ▼] buttons to select on option, at last
press [ok] button. Or press [◄, ►] buttons to select
an option.
View all: Play channels not need password.
7, 12, 15, 18: those option determining that
different stream, whether have to input
password.
Lock all: Play channels need input password.
3. Time Control: Press [ok] button, then press [▲,
▼] buttons to select on option, at last press [ok]
button.
Or press [◄, ►] buttons to select ON
or OFF
On: Play channels not need password only in
Allow time.
OFF: Play channels not need password at any
time.
4. Allow time: Setting the start and end time to
play channels that not need password.
Note: This option you can’t edit when Time
Auto update: Press [ok] button, then press [▲,
▼] buttons to select on option, at last press [ok]
button. Or [◄, ►] buttons select an option
a. ON: Get the time from the channel info that
you will watch.
Note: Now the date and time does not edit.
b. OFF: You need manual set the date and
time.
Note: Now you can't edit the GMT offset
option.
2. YY/MM/DD:
Press number key to set the
date.
3. Time:
Press number key to set the
time.
4. GMT Offset: Press [ok] button, then press
[▲, ▼] buttons to select on option, at last press
[ok] button. Or press [◄, ►] buttons to select
appropriate option.
5. Summer Time: Press [ok] button, then press [▲,
▼] buttons to select on option, at last press [ok]
button. Or press [◄, ►] buttons to select ON or
OFF.
6. Wake up/sleep: Config the STB turn ON and
OFF. If these are setting ON, the STB will turn
on/off at the wake up time/sleep time. If set
wake up channel, it turn on at the channel, or it
at the last channel before STB turn off.
36
Networking
resolution according to the program it’s
playing, different resolution programs
switching perhaps will makes TV screen
flickering.
b. When you connect with A/V or SCART, the
TV has output that only you change to
resolution the TV supports.
5. SPDIF: Press [ok] button, then press [▲, ▼]
buttons to select on option, at last press [ok]
button. Or press [◄, ►] buttons to select Auto
or PCM.
Auto: The play audio track is the stream has.
PCM: It will make Dolby track to PCM track and
then play it, at the channel has Dolby track
6. Dolby Digital HDMI: Press [ok] button, then
press [▲, ▼] buttons to select on option, at last press
[ok]
button. Or press [◄, ►] buttons to select
ON or OFF.
Note: When you connect with HDMI, if select ON
and the TV don’t play the Dolby track, it is not
audio output at the channels that has Dolby
track.
7. Browser Screen Size: Press [ok] button and
select YES to enter into. The default is to adjust top.
You can use [▲, ▼] buttons to adjust top. Then press
[ok] button to adjust bottom, and use [▲, ▼] buttons
to adjust . The order is top -> bottom -> left -> right.
Left and right use [◄, ►] buttons to adjust.
Control is “OFF”
5. Change password and Confirm password:
using to change password.
9.1.4 A/V Output
In this menu, you can set TV_Scart, Screen ratio,
Conversion, TV Standard, SPDIF, Dolby Digital
HDMI.
1. TV_Scart: Press [◄, ►] buttons to switch video
output by RGB or CVBS with SCART cable.
RGB:
CVBS:
2. Screen ratio: Press [◄, ►] buttons to switch
video resolution circularly by the sequence
“4:3<-> 16:9<-> Auto”. Or press [ok] button, and
select it with [▲, ▼] buttons, then press [ok]
button to confirm.
4:3:
Auto - Letterbox - Centre
16:9:
Auto - Pillar Box - Zoom
Auto: The display format follow the channel
details
3. Conversion: Press [◄, ►] buttons to switch the
manner
circularly
by
the
sequence
“LETTER_BOX<->
PAN_SCAN<->
COMBINED<-> IGNORE”. Or press [ok] button,
and select it with [▲, ▼] buttons, then press [ok]
button to confirm.
4. TV Standard: Press [ok] button, then press [▲,
▼] buttons to select on option, at last press [ok]
button. Or press [◄,►] buttons to select an
option.
480<-> 576<-> 720<-> 1080i<->1080p<-> Auto
Note:
a. Auto means system will set the video output
37
Networking
9.1.5 Factory Default
9.1.6 Miscellaneous Setting
This menu is operating for database.
1. Load From Factory Default: Press [ok] button,
it display a warn information, select "YES" to
come back factory default.
Note: If you do Save As Factory Default before,
it will be back the database that you save.
2. Factory Reset: Press [ok] button, it display a
warn information, select "YES" to come back
factory default.
3. Save As Factory Default: Press [ok] button, it
display a warn information, select "YES" to save
the current database as factory default.
4. Delete All Channel: Press [ok] button, it display
a warn information, select "YES" to delete all
channels.
1.
2.
3.
? Frequently Asked Question
Q: IF I incautiously delete all channels, what should I
do?
A: There are two ways to restore:
To re-search all channels in “Installation” function.
Use “Default Value” function to restore all channels in
“Tools” function
4.
5.
38
Banner display time: Press [ok] button, then
press [▲, ▼] buttons to select on option, at last
press [ok] button. Or press [◄, ►] buttons to
select option. It controls the info bar display time.
The options have sec1-sec20.
Osd transparency: Press [ok] button, then
press [▲, ▼] buttons to select on option, at last
press [ok] button. Or press [◄, ►] buttons to
select option.
Standby mode: Press [ok] button, then press
[▲, ▼] buttons to select on option, at last press
[ok] button. Or press [◄, ►] buttons to select
TRUE or FALSE.
TRUE: When standby, only the front panel work,
it save electricity.
FALSE: When standby, it just stop output video
and audio, this case can’t save electricity.
Remote mode: Press [ok] button, then press [▲,
▼] buttons to select on option, at last press [ok]
button. Or press [◄, ►] buttons to select
RC1,RC2 or RC1&2.
RC1: The remote mode must use RC1, or STB
can't receive the control signal.
RC2 : The remote mode must use RC2, or STB
can't receive the control signal.
RC1&2: The remote mode no matter what, the
STB can receive the control signal.
HBBTv: It control HBBTv function. Press [◄, ►]
buttons to change it between ON and OFF.
ON: You can press [red] button to into the web at
has HBBTv function channel.
OFF: The HBBTv function can’t use.
Networking
9.1.7 Tuner Configuration
9.1.9 Contact
This menu control Cable and Terrestrial tuner. Press
[ok] button, then press [▲, ▼] buttons to select on
option, at last press [ok] button. Or press [◄,►]
buttons to select Cable or Terrestrial.
Cable: The Install menu will display Cable Install
menu, then you can scan cable channels.
Terrestrial: The install menu will display Terrestrial
Install menu, then you can scan Terrestrial channels.
This menu is note the message of provider. There are
Name, Telephone and website. At those options,
press [ok] button to enter into contact rename menu
and input relevant messages.
9.1.10 System Information
This menu is show the message about the STB.
There are STBID, System Version, Dbase Version,
Kernel Version, U-Boot Version and Last Update.
9.1.8 Conditional Access
In this menu, Press [ok] button, then press [▲, ▼]
buttons to select on option, at last press [ok] button.
Or press [◄,►] buttons to select Disable or Enable.
Disable: the Conax block can not work.
Enable: the Conax block can work.
9.2 PVR/HDD Setting
In this menu, it has HDD Format, USB Speed
39
Networking
Testing, Record Setting, Timeshift Setting and
Youtuble Record Setting.
the right column show current speed can do what.
9.2.1 HDD Format
9.2.3 Record Setting
The menu show the message about the USB disk.
Format Disk:
1. Press [red] button and press [▲, ▼] buttons to
select a format for the disk, then press [ok]
button to start. This case can hold subarea
2. Press [green] button to enter into the menu:
a. [green] button: Add a new subarea.
b. [yellow] button: Delete a subarea.
c. [red] button: Save and partition the disk.
d. [blue] button: Format disk.
Note: Format disk will lost the disk data.
This menu include Record Path, Duration and
Extend Record Time.
Record Path: Press [ok] button to change the record
path.
Duration: Press [◄, ►] buttons to change the
Duration of each time.
Extend Record Time: Press [◄, ►] buttons to
change the extend time for record. It will add the time
at each begin and end.
9.2.4 TimeShift Setting
This menu include Enable, TimeShift Path and
Time.
Enable: Press [ok] button to select ON and OFF.
TimeShift Path: Press [ok] button to change the
TimeShift path.
Time: Press [◄, ►] buttons to change the TimeShift
time.
9.2.2 USB Speed Testing
This menu use to test the write and read speed of the
USB. You can press [red] button to test again. And
40
Networking
3.
WPA2-PSK, Encryption has TKIP and
AES two options.
Press [red] button to connect.
9.2.5 Youtuble Record Setting
This menu include Enable and Record Path.
Enable: Press [ok] button to select ON and OFF.
Record Path: Press [ok] button to change the record
path.
9.3 Net Setting
9.3.1 Configuring Wi-Fi (wireless)
1.
2.
Select Wireless on Default Network Type item.
Press [red] button the wireless LAN network list
will appear, Select you Wi-Fi network and press
[ok] button, at last input password.
Wireless: The network name.
Access Point Configuration: Press [◄, ►]
buttons to select WEP, WPA2-PSK or
WPA-PSK.
Security Setup/Encryption: Press [◄, ►]
buttons to select an option.
Password: Press [ok] button to input the
password.
Key Number: Press [◄, ►] buttons to
select 1, 2, 3 and 4.
Note:
1. Only the Access Point Configuration
select WEP, the Key Number can display for
use.
2. When Access Point Configuration select
WEP, Security Setup has open and
shared two options. And Access Point
Configuration select WPA-PSK or
9.3.2 Configuring LAN
1. Select Wired on Default Network Type item.
2. You can configure the Ethernet setting options.
DHCP: Apply the options according to the
DHCP.
Manual: Enter the options manually.
3. Press [EXIT] button to save and exit.
41
Networking
9.3.3 Dynamic Setting
9.3.5 Network hard disk
Go to menu/system/IP config menu, press [green]
button enter into setting DDNS menu.
Dynamic Start: Press [◄, ►] buttons to select
ON or OFF.
User: Press [ok] button to input the user name.
Password: Press [ok] button to input the
password.
Host: Press [ok] button to input the host domain
name.
Update Interval (Sec): Use number buttons to
input the time.
Setting those options, you can use network hard disk.
Network hard disk name: Press [◄, ►] buttons
to select an option as the name.
Service type: Press [◄, ►] buttons to select
NFS or CIFS.
Share folder: Press [ok] button to input the
share folder name.
Server IP: Use number buttons to input the
server IP that the share folder belong.
User Name: Press [ok] button to input the
name.
Password: Press [ok] button to input the
password.
Status: Press [◄, ►] buttons to select Active or
Inactive.
Note:
1. The User Name and Password can use, only
when you select the Service type is CIFS. It say,
you must have User Name and Password can
use the network hard disk in this case.
2. Only select status is active, the network hard
disk can display in the file list.
9.3.4 FTP Password
This menu use to change the FTP password.
User name: Display the user name, it can’t be
edited.
Old Password: Press [ok] button to input old
password.
Change password: Press [ok] button to input
new password.
Confirm password: Press [ok] button to input
new password again.
Press [red] button to save.
9.3.6 3G Network
In this menu, it has Access Point Name, Number,
User Name, Password, Mode and status. Except
status, their are all offer by service provider.
42
Networking
9.4 Upgrade
9.4.1 Upgrade from USB
1. Upgrade Type: Press [ok] button, then press [▲,
▼] buttons to select on option, at last press [ok]
button. Or press [◄, ►] buttons to select an
option.
App, App + Plugin, App + Database + Plugin,
Database, App + Database.
2. Folder: Press [ok] button to select correlative
software.
3. Press [red] button to upgrade.
9.4.3 Backup system to HDD
1. Type: Press [ok] button, then press [▲, ▼]
buttons to select on option, at last press [ok]
button. Or press [◄, ►] buttons to select an
option.
App, Plug In, App + Plugin, App + Database +
Plugin, Database, App + Database.
2. Path: Press [ok] button to select the path for
save file.
3. Name: Press [ok] button to rename for the file.
4. Press [red] button to backup.
9.4.2 Upgrade from online
Go to menu/online/upgrade software menu.
1. Press [◄, ►] buttons to switch between
software list and database list.
2. Press [▲, ▼] buttons to select a software or
database.
3. Press [ok] button to display the log.
4. Press [red] button to download and upgrade.
9.4.4 Database Transformer
Note: Don’t power off when upgrade software.
1.
2.
3.
Path: Press [ok] button to select the path for file
Press [red] button to output the files.
Press [green] button to load the files.
Note: The output file can be maked over at PC, then
43
Networking
load in STB.
11 Online
10 Conditional Access
The services of the menu all from online server.
Receiver provide two CA slot for user to use.
Receiver has build in smart card module with CONAX
system. By using cards in this system provided by
operators, it is possible to watch many scrambled
channels coded in this system. This menu shows
detailed information about card inserted into card
reader module. It allows inserted according to help
messages visible on the bottom of the screen.
Note: If it not work or error, please contact the
provider.
11.1 Message
11.1.1 Display message
1. Select the message that you want display with
[▲, ▼] buttons.
2. Press [ok] button to display the detail message.
3. Press [ok] button again, or press [EXIT] button
to cancel display.
11.1.2 Sort message
44
Networking
1.
2.
3.
Press [red] button
Press [▲, ▼] buttons to select an option.
Status, Address, Subject, timer
Press [ok] button.
1. Press [green] button to enter into Add City
menu.
2. Input the city name that you want, and press [red]
button to confirm.
Note:
1. You can only add five cities at most.
2. Press [▲, ▼] buttons to change city.
11.1.3 Delete message
1. Press [green] button to delete the selected
message.
2. Press [yellow] button to delete all message of
the list.
11.2.2 Delete City
11.2 Weather Forecast
11.2.3 Update the information
Press [yellow] button to delete the current city.
Press [red] button to update the information of
current city.
11.2.4 Change Units
Press [blue] button to change the units.
11.2.1 Add City
45
Networking
11.4 User Manual
11.2.5 Switch Date
Press [◄, ►] buttons to switch date.
Note: It only display four dates weather in a city.
11.3 FAQ
11.3.1 Play the demo video
1. Press [◄, ►] buttons to switch frame.
2. Press [▲, ▼] buttons to change item.
3. Press [PLAY] or [ok] button to download and
play the demo video.
11.4.1 Resource transfer mode is
HTTP
1.
2.
Press [◄, ►] and [▲, ▼] buttons to switch item.
Press [ok] button at right column the picture, it
begins to download and play the picture.
11.4.2 Resource transfer mode is FTP
When you enter the User Manual menu, it begins to
download the entire manual.
1. Press [◄, ►] and [▲, ▼] buttons to switch item.
2. Press [ok] button at right column the picture, it
begins to play the picture.
11.3.2 Zoom the video
When play the video:
1. Press [ZOOM] button to zoom it of 1, 4, 9 or 16
times.
2. Press [◄, ►] and [▲, ▼] buttons to move the
zoom place.
11.4.3 Manual playing
Press [◄, ►] button.
Press [▲, ▼] button.
Press [P+, P-] button.
11.4.4 Auto playing
Press [PLAY] button.
46
Networking
HTTP
1.
2.
3.
Press [◄, ►] and [▲, ▼] buttons to switch item.
Press [ok] button at right column, it begins to
download the e-book list.
Press [ok] button at right column, it begins to
download and play the picture.
11.5.2 Resource transfer mode is FTP
1. Press [◄, ►] and [▲, ▼] buttons to switch item.
2. Press [ok] button at right column, it begins to
download the entire e-book.
3. Press [ok] button at right column the picture, it
begins to play the picture.
11.4.5 Zoom the picture
When play the picture:
1. Press [ZOOM] button to zoom it of 1, 4, 9 or 16
times.
2. Press [◄, ►] and [▲, ▼] buttons to move the
zoom place.
Note: Press [EXIT] button to cancel play.
11.5.3 Manual playing
Press [◄, ►]buttons.
Press [▲, ▼] buttons.
Press [P+, P-] buttons.
11.5 E-book
11.5.4 Auto playing
Press [PLAY] button.
11.5.1 Resource transfer mode is
47
Networking
11.5.5 Zoom the picture
5.
When play the picture:
1. Press [ZOOM] button to zoom it of 1, 4, 9 or 16
times.
2. Press [◄, ►] and [▲, ▼] buttons to move the
zoom place.
Note: Press [EXIT] button to cancel play.
6.
7.
Modification menu, and input the E-mail.
Language: Press [ok] button and then using [▲,
▼] buttons to select, at last press [ok] button to
confirm.
User: It shows the STB ID.
Press [red] button to save and register.
11.6.2 Clear online data
Press [yellow] button and select YES, then press [ok]
button to confirm.
Note: After do this the STB will reboot.
11.6 Config
This menu use to register online server and config
online.
11.6.3 Setup online service
Press [green] button to enter into the menu.
Message Auto Play: Press [ok] button, then
press [▲, ▼] buttons to select on option, at last
press [ok] button. Or press [◄, ►]buttons to
select an option.
Enable: The message can display at bottom of
video.
Disable: Can’t display message when play
video.
Software Upgrade Notify: Press [ok] button,
then press [▲, ▼] buttons to select on option, at
last press [ok] button. Or press [◄, ►] buttons
to select an option.
Enable: It give a message when the new version
gives.
Disable: Not message when the new version
gives.
Resource Transfer Mode: Press [ok] button,
then press [▲, ▼] buttons to select on option, at
last press [ok] button. Or press [◄, ►] buttons
to select HTTP or FTP.
11.6.1 Register
1. Name: Press [ok] button to enter into Name
Modification menu, and input the name.
2. Telephone: Press [ok] button to enter into
Telephone Modification menu, and input the
Telephone.
3. Address: Press [ok] button to enter into
Address Modification menu, and input the
Address.
4. E-mail: Press [ok] button to enter into E-mail
48
Networking
12 File List
12.2 Sort files/Sort folder
Enter into this menu has two ways.
Go to menu/File list.
In full screen, Press [FOLDER] button.
In the list, press [green] button, then press [▲, ▼]
buttons to select an option, at last press [ok] button.
Name, Type, Size, Modify date.
12.1 Switch File list
12.3 Delete files/Delete
There are two ways to switch file list.
1. Go to menu/File list menu, press [◄, ►]
buttons to select one icon, then press [ok] button
to enter into the list.
2. In one list press [red] button, then press [▲, ▼]
buttons to select an option, at last press [ok]
button to switch.
Music, Record, Picture, Movie, Software, All
folder
Delete files: In the list, select files with [blue] button,
then press [yellow] button, at last select YES.
Delete folder: In the list, select one folder with [▲, ▼]
buttons, then press [yellow] button, at last select
YES.
Note:
1. You can delete one folder once. If the folder is
storage record file or timeshift file, it can’t be deleted.
2. When in the software list, the [blue] button to
use to upgrade.
Note: Each list only display correlative files. All list
can display else list files.
49
Networking
12.4 Play Record
File/Music/Movie
1. In the list, select one or more files use [blue]
button.
2. Press [PLAY] or [ok] button to playing.
3. Press [PAUSE] button to pause play.
4. Press [◄, ►] buttons to jump the playing place.
5. Press [PAGE-, PAGE+] buttons to play fast.
6. Press [PREV/NEXT] button to jump the
head/end of the file.
7. Press [PLAY MODE] button to select one mode.
: Order and play the all selected
files, then exit.
: Circular play current file.
: Circular play all selected files.
8.
12.6 Online Subtitle
Press [STOP] or [EXIT] button to stop play.
When play a movie file, the info bar hide:
1. Press [blue] button to search and display movie
information from online server.
2. Press [red] button to input the new movie name
to search the movie information.
3. Press [green] button to enter into Search
Subtitle From Internet menu.
File Name: Press [ok] button to input the movie
name that you want search.
Language: Press [◄, ►] buttons to select the
language.
4. Press [red] button to search and display the list.
5. Press [▲, ▼] buttons to select a subtitle.
6. Press [ok] button to download.
Note: if the subtitle is belong the current play movie,
it will be display.
12.5 Play Picture
1. In the list, select one or more files use [blue]
button.
2. Press [PLAY] or [ok] button to playing.
: Turn picture by deasil.
: Turn picture by anticlockwise.
: Play next picture.
: Play anterior picture.
: Order and auto play the all selected
pictures, then exit.
3. Press [STOP] or [EXIT] button to stop play.
50
Networking
Or press [◄, ►] buttons to select one option.
ANSI, UTF-8, UTF-16 Little-Endian, UTF-16
Big-Endian,
Big5,
GB2312,
Turkey(ISO),
Arabic(ISO), Arabic(Windows), Latin2
Language: Press [ok] button, and then press [▲, ▼]
buttons to select a language, at last press [ok] button.
Or press [◄, ►] buttons to select a language.
Site: Press [ok] button, and then use [▲, ▼] buttons
to move the display subtitle place.
Size: using number buttons to input the size.
Note: The size between 30% and 200%.
12.7 Setting Subtitle
When play a movie file, the info bar hide, press
[yellow] button to enter into Subtitle menu:
Subtitle: press [ok] button, and then press [▲, ▼]
buttons to select ON or OFF, at last press [ok] button.
Or press [◄, ►] buttons to select ON or OFF.
ON: Allow to display the downloaded subtitle.
OFF: Can’t display subtitle.
Note: if it select OFF, the other options can’t edit.
Adjust Time: Press [ok] button and use [▲, ▼]
buttons to adjust time, making it synchronous.
Encode: Press [ok] button, and then press [▲, ▼]
buttons to select one option, at last press [ok] button.
51
Networking
14 Networking
13 Plug In
This menu is some internet applications. There are
Youtube, Shoutcast, Picasa, RSS, Opera, Portal,
kartina TV, YouPorn.
This menu is allows user install software by self. It
supports the number of software by the hardware. It
only has a calculating at first.
14.1 Youtube
Youtube can play stream media in www.youtube.com.
13.1 Using the calculating
1.
2.
3.
4.
5.
Press [ok] button to start the function.
Press [green] button to enter into menu.
Press number buttons to input.
Press color and [INFO] buttons to input operator.
Press [EPG] button to clear the input.
14.1.1 Play the video
1. Press [ok] button to connect and display the list.
2. Press [red] button to display the featured video
list.
3. Press [▲, ▼] buttons to select a video.
4. Press [ok] button to downloading and playing on
top left corner.
5. Press [ok] button again to playing in mid of
screen.
6. Press [ZOOM] button, the video will play in full
screen.
7. Press [PAUSE] button to pause the video.
52
Networking
8.
9.
Press [PLAY] button to continue play video.
Press [STOP] button to stop the video.
3.
Game, News, Tech, Movie and so on.
Press [ok] button.
14.1.4 Display the top video
1.
2.
Press [blue] button.
Press [▲, ▼] buttons to select an option.
Top favoufites, Top rated, Most views, Most
recent and so on.
3. Press [ok] button.
14.1.5 Display the relate videos
Press [F1] button to display the relate videos about
the highlight video.
14.1.2 Sort for the list
14.1.6 Download the video
1.
2.
Press [green] button.
Press [▲, ▼] buttons to select Site or Duration.
Site: it includes Germany, Worldwide, Poland
and so on.
Duration: it includes All Time, This Week, This
Month and so on
1. Go
to
the
System->PVR/HDD
Setting->Youtube Record Setting menu to set the
path of the file save.
2. Press [RECORD] button to start downloading
the video file.
3. Press [FOLDER] button to enter into the
downloading list.
14.2 Shoutcast
This menu is radio in www.shoutcast.com.
14.1.3 Change group
1.
2.
Press [yellow] button.
Press [▲, ▼] buttons to select an option.
53
Networking
14.2.1 Play the radio
14.2.3 Add to Favorites
Press [ok] button to downloaded and then play it.
1. Press [▲, ▼] buttons to select.
2. Press [yellow] button
Note: Press [green] button to switch favorites list.
14.2.4 Find radio
1.
2.
3.
14.2.2 Select Genre
1.
2.
3.
Press [red] button.
Press [▲, ▼] buttons to select an option.
Press [ok] button.
54
Press [FIND] button
Input the keyword.
Press [red] button to confirm and find
Networking
14.3.3 Display the album
Press [yellow] button to display the album of the
highlight picture.
14.4 RSS
This menu is display RSS web.
14.3 Picasa
This menu is picture in www.picasa.com
14.4.1 Add new subscription
Press [red] button to enter into Subscription menu,
and then input the URL, at last press [red] button to
confirm and save.
14.3.1 Display the picture
1. Press [▲, ▼] and [◄, ►] buttons to select one
picture.
2. Press [ok] button
3. Press [◄, ►] buttons to display the anterior or
next picture.
14.4.2 Delete subscription
Press [green] button and then select YES, at last
press [ok] button.
14.3.2 Display the user’s album
Press [green] button to show the user’s album of the
highlight picture.
55
Networking
14.4.3 Edit
14.4.5 Sort the news list
1.
2.
3.
1.
2.
3.
Press [yellow] button.
Press [▲, ▼] buttons to select Name or URL.
Press [ok] button to input the name or URL, then
press [red] button to confirm and save.
In the list, press [red] button.
Press [▲, ▼] buttons to select Date or Title.
Press [ok] button.
14.5 Opera
14.4.4 Display Subscription
This menu is a Browser that called opera. You can
use it like IE.
1. Press [ok] button to display the news list.
2. Press [▲, ▼] buttons to select a news.
3. Press [ok] button to display detail information.
4. If it has several pages, press [P+/P-] buttons to
display anterior or next page.
14.6 FTP Client
This menu use to download file from FTP server
56
Networking
14.6.1 Switch Group
When the cursor is on the left column:
1. Press [red] button.
2. Press [▲, ▼] buttons to select Browse Server,
Downloading List or Downloaded List.
3. Press [ok] button.
14.6.4 Display the information about
the downloading / downloaded file
In the Downloading List or Downloaded List, there
are two ways to display the information.
When the cursor is on the left column:
※ Press [INFO] button.
Note: Press [INFO] or [EXIT] button to cancel
display.
14.6.2 Option
When the cursor is on the left column:
1. Press [green] button.
2. Press [▲, ▼] buttons to select Select All,
Unselect All or Select Others.
3. Press [ok] button.
※ Press [►] button, and then press [▲, ▼] buttons
to select info, at last press [ok] button.
Note: Press [ok] or [EXIT] button to cancel display
14.6.5 Add/Edit server
14.6.3
Setting
downloading
Go to menu/download menu
1. Press [►] button.
2. Press [▲, ▼] buttons to select Add.
3. Press [ok] button to enter into the menu:
Server Name: Press [ok] button to enter
into Server Name menu, and then input the
name.
FTP Server URL: Press [ok] button to enter
into Server URL menu, and then input the
files
number at the same time
When the cursor is on the left column:
1. Press [yellow] button.
2. Press [▲, ▼] buttons to select 1, 2 or 3.
3. Press [ok] button.
57
Networking
URL.
Anonymous FTP: Press [◄, ►] button to
select NO or YES.
User Name: Press [ok] button to enter into
User Name menu, and then input the name.
Password: Press [ok] button to enter into
Password menu, and then input the
password.
Server Description: Press [ok] button to
enter into Server Description menu, and
then input the description.
Press [green] button to test connect FTP
server.
Press [red] button to add the server.
Note: When Anonymous FTP select NO, the User
Name and Password can’t edit.
1. Press [▲, ▼] buttons to select server.
2. Press [►] button.
3. Press [ok] button to connect the server, and then
enter into the File List.
14.6.8 Refresh File List
1. Connect server.
2. Press [►] button.
3. Press [▲, ▼] buttons to select Refresh, and
then press [ok] button.
14.6.9 Add Downloading File
1. Connect server.
2. Press [▲, ▼] buttons to select a file.
3. Press [►] button.
4. Press [▲, ▼] buttons to select Download, and
then press [ok] button.
Source File URL: Display the source file URL.
Rename: Press [ok] button to enter into
Rename menu, and then input the name.
Save to: Press [ok] button to select the folder to
storage the downloading file.
Press [red] button to confirm and start
downloading.
14.6.6 Delete Servers
1. Press [ok] and [▲, ▼] buttons to select servers.
2. Press [►] button.
3. Press [▲, ▼] buttons to select Delete, and
select YES.
14.6.7 Connect Server
58
Networking
14.6.10 Stop Downloading
14.7 Kartina TV
In the Downloading List:
1. Select the downloading files.
2. Press [►] button.
3. Press [▲, ▼] buttons to select Stop.
4. Press [ok] button.
This menu is play video on “www.kartina.tv.”
1. Press [red] button to display channel list.
2. Press [green] button to display the channel EPG
list.
3. Press [yellow] button to display the VOD list
.
14.6.11 Make Stopping Download
files to Start
In the Downloading List:
1. Select the stopping files.
2. Press [►] button.
3. Press [▲, ▼] buttons to select Start.
4. Press [ok] button.
14.7.1 Login
1.
2.
3.
Press [menu] button.
Input User Name and Password.
Press [green] button to save and login.
14.6.12 Delete files
In the Downloading List or Downloaded List:
1. Select the files that you want delete.
2. Press [►] button.
3. Press [▲, ▼] buttons to select Delete.
4. Press [ok] button, then select YES.
14.7.2 Play Video
59
Networking
1.
2.
3.
Press [▲, ▼] buttons to choose an channel.
Press [ok] button to play it.
Press [ok] button again to play it in full screen.
15 Portal
14.7.3 Switch Group/Service
1. Press [folder] button to display the group menu.
2. Press [▲, ▼] buttons to choose a
group/Service.
3. Press [ok] button to confirm.
15.1 Setting Language
1. Press [ok] button to enter into Spark Portal
menu.
2. Press [ ►] button to select Setting.
3. Press [◄, ►] and [ok] buttons to select one or
more language.
4. Press [◄, ►] and [▲, ▼] buttons to select OK
button
.
5. Press [ok] button to affirm and exit.
14.7.4 Switch Date/Type
Press [◄, ►] buttons to switch date/type.
14.7.5 Display the information at VOD
list.
Press [INFO] button to display the information about
the video.
15.2 Add App
1.
2.
3.
4.
60
Press [ok] button to enter Spark App Store.
Press [◄, ►] and [▲, ▼] buttons to select one
point.
Press [ok] button to enter.
Press [◄, ►] buttons to select Add to portal.
Networking
Note: App Store and Setting can't move.
15.5 Run APP
In Spark App Store menu:
1. Press [◄, ►] and [▲, ▼] buttons to select one
point.
2. Press [ok] button to enter.
3. If you are adding, press [▲, ▼] buttons to select
Run. Or you must press Add to portal first, and then
select Run.
4. Press [ok] button.
In Spark Portal menu:
1. Press [◄, ►] and [▲, ▼] buttons to select one
point.
2. Press [ok] button.
15.6 Navigation Menu
1. Press [MENU] button to display the navigation
menu.
15.3 Remove App
In Spark App Store menu:
1. Press [◄, ►] and [▲, ▼] buttons to select
one point that you are added.
2. Press [ok] button to enter.
3. Press [▲, ▼] buttons to select Remove
from portal.
2. Press
icon to display the default internet
point.
3. Press
icon to display a browser, you can use it
like IE.
In Spark Portal menu:
1. Press [◄, ►] and [▲, ▼] buttons to select
one point.
2. Press [blue] button to enter.
3. Press [▲, ▼] buttons to select Remove
from portal.
15.4 Move App
In Spark Portal menu:
1. Press [◄, ►] and [▲, ▼] buttons to select one
point.
2. Press [yellow] button.
3. Press [◄, ►] and [▲, ▼] buttons to move it.
4. Press [ok] button to confirm.
4. Press
icon to make browser to display front
internet point that you linked.
5. Press
icon to make browser to display next
internet point that you linked.
61
Networking
6. Press
icon to refresh the information.
7.
Press
icon to startup/cancel soft keyboard.
8.
Press
icon to startup/cancel mouse.
9.
Press
icon to exit spark portal.
10. Press
icon to display the help information.
62
Addenda
16 Trouble Shooting
If you suspect there is a fault with your receiver, please check the following trouble shooting guide
before calling authorized service agent.
Warning! Under no circumstances attempt to repair the receiver yourself. Tampering with the receiver may result
in fatal electric shock and will invalidate your warranty.
Symptom
Possible cause
Settings you made in the
menu have not change
The receiver lost power before being able to enter into standby mode
Some of the Settings saved by user can be deleted partly or fully
No signal
The level of signal is weak
LNB is out of order
The cable from the LNB or Terrestrial is incorrectly Connected (short
circuit or open circuit)
The position of dish is aligned incorrectly
Receiver is on but no picture
or sound except the following
messages (NO TV program)
Channel is not available
Channel is scramble
Receiver not responding to
remote control unit
RCU batteries are dead or inserted incorrectly
The RCU is pointing toward wrong direction
Poor picture Quality
The level of Signal strength is low
No sound
The cable is connected incorrectly
The Volume level is low
Muting function is active
No display on
Display
the LED
No picture on the screen
The power cord is not plugged in correctly.
Receiver is in Standby mode
RCA Jack or cable is not connected firmly to the video output port of
television
Incorrect channel or video output is selected on television
Brightness level of your TV set is incorrectly defined
63
Addenda
17 Specifications
SYSTEM RESOURCES
Main Processor
450M Hz based CPU
Flash Memory
Nor flash:8MB X 1 ; Nand flash:512MB X 1
DDR SDRAM
DDR2 128MB x 2
Tuner/Front-end(Optional)
Tuner Type
DVB-S / DVB-S2
Input Connector
F-type, Connector, Female
Loop Through
F-type, Connector, Female
Signal Level
-65 to -25 dBm
LNB Power & Polarization
Vertical: +13V/+14V
Horizontal: +18V/+19V
Current: Max. 500mA
Overload Protection
22KHz Tone
Frequency: 22±1KHz
DiSEqC Control
Amplitude: 0.6±0.2V
Version 1.0, 1.1 1.2, USALS Available
Demodulation
QPSK, 8PSK
Input Symbol Rate
2-45 Mbps, Convolution Code Rate
1/2, 2/3, 3/4, 5/6,7/8,1/4,1/3,2/5,3/5,4/5,8/9,9/10 and Auto
POWER SUPPLY
Input Voltage
Free Voltage (100~240V AC, 50/60Hz)
Power Consumption
20W MAX
MPEG TS A/V Decoding
Transport Stream
MPEG-2, H.264
Input Rate
Max.120Mbit/s
Aspect Radio
4:3, 16:9, Letter Box
Video Decoding
MPEG-2, MP@ML, MPEG-4 part 10/H264
Video Resolution
720*480P/I, 720*576P/I, 1280*720p,1920*1080i, 1920*1080p
Audio Decoding
MEPG-1 layer I/II, Mpeg2 layerII, Dolby digital
Audio Mode
Left / Right / Stereo/ Mono
Sampling Rate
32, 44.1 and 48KHz
A/V & DATA INPUT/OUTPUT
TV-SCART
RCA A/V
S/PDIF
RS-232C
RJ-45
Video CVBS/RGB output
Audio L/R output
Video CVBS output
Audio L/R output
Coaxial, Digital Audio or Dolby Digital Bit Stream Output
Transfer rate 115.2Kbps
9 pin D-sub Type
10M/100M
64
Addenda
USB
HDMI
One USB 2.0 slot Compatible for Host
VER1.2
Type A
PHYSICAL SPECIFICATION
Size[W*H*D]
300mm*64mm*231mm
Net Weight
1.56KG
Operation Temperature
0℃~+45℃
Storage Temperature
-10℃~+70℃
Storage Humidity
5%~95% RH (Non-Condensing)
65