Digital Keypad with RFID Access Control
User Manual
Contents:
Name
Digital Keypad
User manual
Screw driver
Rubber bungs
Self tapping screws
Manager Card
Quantity
1
1
1
4
4
2
Remarks
6*27mm, used for fixing
3.5*27mm, used for fixing
Manager Add Card & Manager Delete Card
Specifications
Operating Voltage
User Capacity
Keypad
Card Type
Card Reading Distance
Active Current
Idle Current
Lock Output Load
Alarm Output Load
Operating Temperature
Operating Humidity
Environment
Adjustable Door Relay time
Adjustable Alarm Time
Wiegand Interface
Wiring Connections
Dimensions
Net Weight
Gross Weight
9-18V AC/12~24V DC
2,000
12 keys, 3 x 4 digits
EM 125 KHZ card
3~6 cm
<80mA
≤40mA
Max 2A
Max 20A
-20~60
5%~95% RH
Conforms to IP68
0 ~ 99 seconds
0 ~ 3 minutes
Wiegand 26 input & output
Electric Lock, Exit Button, DOTL, External Alarm
L128 x W82 x H28 m
550 g
700 g
Installation

Remove the back cover from the keypad using the supplied security screwdriver

Drill 4 holes on the wall for the screws and I hole for the cable

Fix the back cover firmly on the wall with 4 flat head screws

Thread the cable through the cable hole

Attach the keypad to the back cover.
Wiring
Color
Function
Description
Green
White
Grey
Yellow
Brown
Red
Black
Blue
Purple
Orange
Pink
D0
D1
Alarm OPEN
D-In
AC&DC
AC&DC
NO
COM
NC
GND
Wiegand Output D0
Wiegand Output D1
Alarm Negative
Request to Exit Button
Door Contact
9-18V AC/12~24V DC Regulated Power Input
9-18V AC/12~24V DC Regulated Power Input
Relay NO
Relay COM
Relay NC
Negative
Connection Diagram
Notes:
Connect the negative pole of the lock to NC is for Fail safe lock.
Connect the negative pole of the lock to NO is for Fail-secure lock.
To Reset to Factory Default
To reset to factory default, power off, press * , hold it and power on, release it until hear two
beeps and the LED shines in orange, then read any two EM cards, the LED will turn in red,
means reset to factory default setting successfully. Of the two EM cards read, the first one is
Manager Add card, the second one is Manager Delete card.
Remarks: Reset to factory default, the user’s information is still retained.
Anti Tamper Alarm
The keypad uses a LDR (light dependent resistor) as an anti tamper alarm. If the keypad is
removed from the cover then the tamper alarm will operate.
Sound and Light indication
Operation Status
Red Light
Green Light
Yellow Light
Buzzer
Power on
Stand by
Press keypad
Bright
Bright
-
-
-
Short Ring
Short Ring
Operation successful
Operation failed
Enter into programming mode
Bright
Bright
-
-
Short Ring
3 Short Rings
Short Ring
In the programming mode
Exit from the programming
mode
Open the door
Alarm
Bright
-
Bright
-
Short Ring
Bright
Bright
-
-
Short Ring
Alarm
Detailed Programming Guide
User Settings
To enter the programming mode
* Master code #
888888 is the default factory master code
To exit from the programming mode
*
Note that to undertake the following programming the master user must be logged in
To change the master code
0 New code # New code #
The master code is any 6 digits
Setting the working mode:
Set valid card only users
3 0 # Entry is by card only
Set valid card and PIN users
3 1 # Entry is by card and PIN together
Set valid card or PIN users
3 2 # Entry is by either card or PIN (default)
To add a user in either card or PIN mode ( 3 2 # ) (Default setting)
To add a Pin user
1 User ID number # PIN #
The ID number is any number between 1 ~ 2000.
The PIN is any 4~8 digits between 0000 ~
99999999 with the exception of 1234 which is
reserved. Users can be added continuously without
exiting from programming mode as follows:
1 User ID no 1 # PIN # User ID no 2 # PIN #
To delete a PIN user
2 User ID number #
Users can be deleted continuously without exiting
programming mode
To change the PIN of a PIN user
* ID number # Old PIN # New PIN # New PIN #
(This step must be done out of
programming mode)
To add a card user (Method 1)
1 Read card #
This is the fastest way to enter cards
Cards can be added continuously without exiting
using ID number auto generation.
programming mode
To add a card user (Method 2)
This is the alternative way to enter
cards using User ID Allocation. In this
method a User ID is allocated to a
1 ID number # Card #
card. Only one user ID can be
allocated to a single card.
To add card user (Method 3)
Add a series cards users – Block
Enrollment
5 ID number
quantity #
#
8 digits Card number
# Card
Card quantity is between 1 ~ 2000. The 8 digits card
number is the last 8 digits on the card.
Maximum 2000 cards can be enrolled at a stretch
within 2 minutes.
To delete a card user by card number.
Note
users
can
be
deleted
continuously
without
exiting
programming mode
2 Read Card
To delete a card user by user ID. This
option can be used when a user has
lost their card
2 User ID #
#
To add a card and PIN user in card and PIN mode ( 3 1 # )
To Add a card and Pin user
Add the card as for a card user
(The PIN is any 4~8 digits between
Press * to exit from the programming mode
0000 & 99999999 with the exception of
Then allocate the card a PIN as follows:
1234 which is reserved.)
* Read card 1234 # PIN # PIN #
To change a PIN in card and PIN mode
(Method 1) Note that this is done
outside programming mode so the
user can undertake this themselves
* Read Card Old PIN # New PIN # New PIN #
To change a PIN in card and PIN mode
(Method 2) Note that this is done
outside programming mode so the
user can undertake this themselves
* ID number # Old PIN # New PIN # New PIN #
To delete a Card and PIN user just
delete the card
2 User ID #
To add a card user in card mode ( 3 0 # )
To Add and Delete a card user
The operating is the same as adding and deleting a
card user in 3 2 #
To delete All users
To delete ALL users. Note that this is
a dangerous option so use with care
To set card users by Manager card
2 0000 #
Manager add card Read card Manager add card
To add user by Manager Add Card
Cards can be added continuously.
To delete User by Manager Delete Card
Manager delete card Read Card Manager delete card
Cards can be deleted continuously.
Door Relay, Door Detecting, Alarm Settings
Door relay time setting
To set door relay strike time
4 0~99 #
The door relay time is between 0~99 seconds, the factory default
setting is 5 seconds.
Door Open Detection
Door Open Too Long (DOTL) warning. When used with an optional magnetic contact or built-in
magnetic contact of the lock, if the door is opened normally, but not closed after 1 minute, the inside
buzzer will beep automatically to remind people to close the door and continue for 1 minute before
switching off automatically.
Door Forced Open warning. When used with an optional magnetic contact or built-in magnetic
contact of the lock, if the door is opened by force, or if the door is opened after 20 seconds of the
electro-mechanical lock not closed properly, the inside buzzer and alarm output will both operate.
The Alarm Output time is adjustable between 0~3 minutes with the default being 1 minute.
To disable door open detection.
6 0 #
(Factory default)
To enable door open detection
6 1 #
Alarm output time
To set the alarm output time (0~3
minutes) Factory default is 1 minute
9 0~3 #
Keypad Lockout & Alarm Output options. If there are 10 invalid cards or 10 incorrect PIN numbers
in a 10 minute period either the keypad will lockout for 10 minutes or the alarm will operate for 10
minutes, depending on the option selected below.
Normal status: No keypad lockout or
alarm (factory default)
7 0 # (Factory default setting)
Keypad Lockout
7 1 #
Alarm Output
7 2 #
To remove the alarm
To reset the Door Forced Open warning
To reset the Door Open Too Long
warning
Read valid card or Master Code #
Close the door or Read valid card or Master Code #
Interconnecting Two Devices
Operating as a Wiegand Output Reader
In this mode the keypad supports a Wiegand 26 bit output so the Wiegand data lines can be
connected to any controller which supports a Wiegand 26 bit input. See figure 1.
Figure 1
Transmission Format:
1: Keypad Transmission
The Reader will transmit the PIN data when it receives the last key (#) press after PIN
code.
Format: PIN Code (any 4~8 digits between 0000 ~ 99999999)
Example: PIN code: 111111
Press 111111 #, then the output format will be: 00111111
(Note: if press an invalid PIN (any 4~8 digits), the data will be also transmitted.)
2: Proximity Card Transmission
The Reader will transmit the card data when it reads the Card.
Format: Card Number (the last 8 digits of Card Number)
(Note: no matter the card is valid or invalid, the data will be transmitted)
Operating as a Controller
In this mode the keypad supports a Wiegand 26 bit input so an external Wiegand device with
a 26 bit output can be connected to the Wiegand input terminals on the unit. Either an ID
card reader (125 KHZ) or an IC card reader (13.56MHZ) can be connected to the keypad.
Cards are required to be added at the external reader, except where an external EM reader
is used, in this case cards can be added at either reader or controller. See figure 2.
Figure 2
Quick Reference Programming Guide
To enter the programming mode
* Master code #
888888 is the default factory master code
To exit from the programming mode
*
Note that to undertake the following programming the master user must be logged in
To change the master code
0 New code # New code #
The master code can be 6 digits long
To add a PIN user
1 User ID number # PIN #
The ID number is any number between 1 ~ 2000. The
PIN is any 4~8 digits between 0000 ~ 99999999 with the
exception of 1234 which is reserved. Users can be
added continuously without exiting programming mode
To add a card user
1 Read Card #
Cards can be added continuously without exiting from
programming mode
To delete a PIN or a card user.
2 User ID number # for a PIN user or
2 Read Card # for a card user
Users can be deleted continuously without exiting from
programming mode
To unlock the door
To unlock the door for a PIN user
Enter the PIN then press #
To unlock the door for a card user
Present the card