optiPoint 150 S
User Manual
Safety Precautions
Safety Precautions
For Your Safety
The optiPoint 150 S IP phone conforms to the European standard EN 60
950 which governs the safety of information technology equipment including electronic office equipment. This device has been designed with safety in mind, thus protecting both individuals and objects.
There is always the danger of small objects being swallowed by young children. In the case of optiPoint 150 S, this applies in particular to the connecting cord clip.
Please make sure that such items are not accessible to children.
• Use only the enclosed power supply together with the special LAN cable.
• Never open the power supply enclosure.
Protecting Your Telephone
•
•
•
The telephone must not be used in bathrooms, etc. as it is not splashproof.
Before connecting or disconnecting the LAN cable, disconnect the
power plug from the wall outlet first.
Never allow the device to come into contact with staining or aggressive
liquids, such as, coffee, tea, juice, or soft drinks.
Choosing the Installation Location
•
•
•
•
•
2
The telephone should be operated in a controlled environment with an
ambient temperature between 5°C and 40°C (41°F and 104°F).
To ensure good handsfree talking quality, the area in front of the microphone (front right) should be kept clear. The optimum handsfree distance is 20 inches (50 cm).
Do not install the telephone in a room where large quantities of dust
accumulate; this can considerably reduce the service life of the telephone.
Do not expose the telephone to direct sunlight or any other source of
heat, as this is liable to damage the electronic equipment and the plastic casing.
Do not operate the telephone in damp environments such as bathrooms.
Safety Precautions
Important Information
Do not operate the telephone in environments where there is a danger of
explosions.
Use only original Siemens accessories. The use of other accessories is dangerous and will invalidate the warranty and the CE mark.
Never open the telephone or a key module. In the event of problems, consult your service personnel.
The information provided in this document contains merely general descriptions or characteristics of performance which in case of actual use do not always apply as described or
which may change as a result of further development of the products. An obligation to provide the respective characteristics shall only exist if expressly agreed in the terms of contract.
The trademarks used are owned by Siemens AG or their respective owners.
Marks
The device conforms to the EU directive 1999/5/EC, as attested by the CE
marking.
This device has been manufactured in accordance with a certified environmental management system (ISO 14001). This process ensures that energy
consumption and the use of primary raw materials are kept to a minimum,
thus reducing waste production.
All electrical and electronic products should be disposed of separately from
the municipal waste stream via designated collection facilities appointed by
the government or the local authorities.
The correct disposal and separate collection of your old appliance will help
prevent potential negative consequences for the environment and human
health. It is a precondition for reuse and recycling of used electrical and electronic equipment.
For detailed information about disposal of your old appliance, please contact
your city office, waste disposal service, the shop where you purchased the
product or your sales representative.
The statements quoted above are only fully valid for equipment which is installed and sold in the countries of the European Union and is covered by
the directive 2002/96/EC. Countries outside the European Union may have
other regulations regarding the disposal of electrical and electronic equipment.
3
Contents
Contents
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protecting Your Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Choosing the Installation Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Marks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
2
3
3
General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . .7
About These Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Echo Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information and Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Availability of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reference to Operating Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
7
8
8
8
8
9
9
Control Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Making Calls – Basic Functions . . . . . . . . . . . . . . . .11
Accepting Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a Call Using the Handset . . . . . . . . . . . . . . . . . . . . . . . .
Open Listening in the Room During a Call. . . . . . . . . . . . . . . . . . . .
Deactivating the Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing/Making Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing a Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Redialing a Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ending a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telephone Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Ringer Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Handset Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Speaker Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
11
11
11
11
12
12
13
13
14
14
14
14
Contents
Making Calls – Enhanced Functions . . . . . . . . . . . . 15
Accepting Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing/Making Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Call Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing from the Phone Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
During a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-Way Conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing the Phone Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding an Entry to a Phone Book . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing a Telephone Book Entry. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting a Phone Book Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting all Phone Book Entries. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Call Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying Missed Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying Received Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying Dialed Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing a Phone Number from the Call Log . . . . . . . . . . . . . . . . . . .
Transferring a Phone Number to the Phone Book . . . . . . . . . . . . . .
Deleting a Phone Number from the Call Log . . . . . . . . . . . . . . . . . .
Deleting Entries in All Call Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing the Voice Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
16
16
17
18
18
18
20
20
21
22
22
23
23
23
24
24
25
25
26
26
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Configuring Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating and Deactivating Forwarding. . . . . . . . . . . . . . . . . . . . . .
Configuring Forwarding Destinations. . . . . . . . . . . . . . . . . . . . . . . .
Activating and Deactivating Don’t Disturb . . . . . . . . . . . . . . . . . . . . . . .
Configuring Properties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Date Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring the Time Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting a Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting a Country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Ringer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring Voice Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying the Current Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
27
28
28
29
29
30
30
31
31
32
32
Web-Based Management Tool . . . . . . . . . . . . . . . . . 34
5
Contents
General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preparatory Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening the Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Setup Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
35
35
36
36
36
37
38
Parameter Description . . . . . . . . . . . . . . . . . . . . . . . .40
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Fixing Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Caring for Your Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Forwarding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
During a Call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
On Busy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contacts in the Case of Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
48
49
49
49
49
50
50
50
51
52
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Menu Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
RFC Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
6
General Information
General Information
About These Operating Instructions
These operating instructions will help you get to know the optiPoint 150 S
and use its functions. The instructions contain important information for
safe and proper operation of the optiPoint 150 S. Follow them carefully to
avoid improper operation and get the most out of your multi-function telephone in a network environment.
Everybody involved in installing, operating or programming the
optiPoint 150 S must read these operating instructions.
For your own protection, please carefully read the section on safety.
Follow the safety instructions carefully in order to avoid endangering
yourself or other persons and to prevent damage to the unit.
The layout of this operating manual is extremely user-friendly. You will be
guided through operation of the optiPoint 150 S step by step – starting
with a description of simple basic functions, through configuration of all
operating parameters to a description of the additional features.
You can configure the telephone in two ways:
• locally at the telephone, see Æ page 27
• via remote maintenance over LAN, see Æ page 34
Administrative tasks are described in a separate manual. The quick reference guide is meant to give you quick and reliable explanations regarding
frequently used functions.
Intended Use
The optiPoint 150 S telephone is a desktop unit designed for voice transmission and for connection to a LAN. It can be operated also as a standalone unit. Any other use is regarded as not prescribed.
Product Identification
The properties of the telephone – exact product name and serial number
– are displayed on the nameplate on the underside of the telephone.
Please have these at hand when you contact our Service department regarding problems or defects on the unit itself.
7
General Information
Echo Effect
In some cases, while using the telephone you may hear an echo, which
can be quite strong. This is not due to any design defect or other fault with
your IP telephone, but is caused by the other client. For example, if the
echo occurs during a teleconference, it may be that the speakers and microphones need to be repositioned.
Service
The Siemens Service department can only help you with problems
or defects on the unit itself.
Should you have any questions regarding the operation, your specialist retailer or network administrator will gladly help you.
For any questions regarding the telephone connection, please contact your network provider.
In the event of any trouble or defects on the unit itself, please dial the service number for your country.
Information and Icons
Safety
Information regarding the prevention of injury or damage is highlighted, as
it contains important instructions on how to use the unit correctly.
7 en may result in injury or in damage to the unit.
This symbol indicates a hazard. Failure to follow the instructions giv-
Key information important for the proper use of the telephone
8
General Information
Availability of Features
Your optiPoint 150 S can be operated on the following communication platforms:
• HiPath 2000
• HiPath 3000
• HiPath 4000
• HiPath 5000
• HiPath 8000
• Broadsoft
• Sylantro
General feature availability cannot be guaranteed for the communication
platforms listed above. A number of the functions described here may not
be available or may be restricted in scope depending on the communication platform used. Contact the service personnel for information on the
features available on your communication platform or refer to the relevant
platform documentation.
As a rule, optiPoint 150 S can also operate at a DSL router in connection
with offerings from other VoIP providers. However, the feature scope described in this operating manual cannot be guaranteed in this case by the
telephone’s manufacturer. Even though optiPoint 150 S is fully compatible
with general SIP standards, some of the functions described here may not
be supported in view of the varying range of functions available from other
VoIP providers and the number different network configurations implemented. An overview of RFC standards that are compatible with
optiPoint 150 S is provided at the back of this manual, see Æ page 57.
Reference to Operating Steps
The following icons are used to indicate the various operating steps:
Operation on the optiPoint 150 S, see Æ page 27.
Operation via the Web-based Management Tool, see Æ page 34.
9
Control Elements
Control Elements
Handset
Display (2 lines with 16 characters per line)
Loudspeaker for open listening and ringers
Function keys
Key for activating/deactivating the loudspeaker
Dialing keypad
Volume control keys
function keys
Key for opening/closing the menu
Delete key
In the editor: deletes the last character
Keys for scrolling through and confirming functions
Key for opening/closing the phone book
Redial key (last phone number)
Consultation key
Conference key
Key for deactivating the mute function
10
Making Calls – Basic Functions
Step by Step
Making Calls – Basic Functions
Accepting Calls
Answering a Call Using the Handset
The telephone rings. The caller’s number is displayed.
2 2 2 8 7 5 8 8
P e t e r
The caller’s name is also displayed if it is stored in the
phone book.
N o r t o n
n Lift the handset.
Open Listening in the Room During a Call
s You are conducting a call.
Press this key. The (red) LED lights up. The call is
switched to loudspeaker.
Inform the party at the other end of the line that
you are switching to loudspeaker.
or
Adjust the volume. To raise or lower the volume, keep
pressing the keys until the desired volume is set.
For an alternative method of adjusting the loudspeaker’s receiving volume, see Æ page 43.
Deactivating the loudspeaker
Press this key. The (red) LED goes out.
Deactivating the Microphone
s You are conducting a call.
Press this key. The (red) LED lights up. The microphone
is deactivated.
Activating the microphone
Press this key. The (red) LED goes out. The microphone
is activated.
11
Making Calls – Basic Functions
Step by Step
Dialing/Making Calls
Dialing a Number
Off-hook dialing
n Lift the handset.
p Enter the phone number.
if necessary
Press this key to delete the last digit.
or
Press this key. The number is dialed.
or Wait for dialing to start automatically.
C a l l i n g …
P e t e r
N o r t o n
If the phone number is stored in the phone book, the
corresponding name is displayed on the second line.
On-hook dialing
p Enter the phone number.
if necessary
Press this key to delete the last digit.
n Lift the handset. The number is dialed.
C a l l i n g …
P e t e r
12
N o r t o n
If the phone number is stored in the phone book, the
corresponding name is displayed on the second line.
Making Calls – Basic Functions
Step by Step
Redialing a Number
Off-hook dialing
n Lift the handset.
Press this key to dial the last number dialed. The number is immediately dialed.
On-hook dialing
Press this key to display the last number dialed.
n Lift the handset. The number is dialed.
Ending a Call
t Replace the handset.
13
Making Calls – Basic Functions
Step by Step
Telephone Settings
Adjusting the Ringer Volume
For a detailed explanation, see Æ page 45.
or
R i n g e r
V o l u m e
„„„†††††
Press one of these keys while the phone is idle.
Press
quire.
or
until you have set the volume you re-
The setting is automatically saved.
Adjusting the Handset Volume
For a detailed explanation, see Æ page 42.
or
H a n d s e t
V o l u m e
„„„„„†††
Press one of the keys while the handset is off hook.
Press
quire.
or
until you have set the volume you re-
The setting is automatically saved.
Adjusting the Speaker Volume
For a detailed explanation, see Æ page 43.
or
S p e a k e r
„„„„„„„†
V o l u m e
Press one of the keys while the loudspeaker is active
(for example, in open listening mode during a call).
Press
quire.
or
until you have set the volume you re-
The setting is automatically saved.
14
Making Calls – Enhanced Functions
Step by Step
Making Calls – Enhanced Functions
Accepting Calls
Call Waiting
The "Call Waiting" feature must be activated, see
Æ page 41.
Prerequisite: You are conducting a call and hear a tone.
Ending the first call and answering the waiting call:
t Replace the handset. Your telephone rings.
n Answer the second call. Lift the handset.
Placing the first call on hold and answering the second call
3 2 3 4 9 3 4 0
A n s w e r
C a l l ?
if necessary
Press
or
to accept the waiting call. The first call
is placed on hold.
Press this key to switch or toggle between the two callers.
15
Making Calls – Enhanced Functions
Step by Step
Dialing/Making Calls
Using the Call Log
Calling back a missed call
1 3 : 5 5
2
m i s s e d
0 2 = K a r l
0 8 : 0 4 p m
2 8 . 1 0 . 0 5
C a l l s
M a y e r
0 2 . 1 4 .
Ú
Any missed calls are displayed on the second line of the
display when the telephone is idle.
Press
or
call back.
to select the missed call you want to
n Lift the handset. The number is dialed.
You can select extra options if you access the call
logs Æ page 23.
Redialing a previously dialed number
Prerequisite: Only possible when there are no missed
calls.
or
0 2 = K a r l
0 8 : 0 4 p m
Press this key to display a list of the last numbers dialed.
M a y e r
0 2 . 1 4 .
Ú
Press
dial.
or
to select the number you want to re-
n Lift the handset. The number is dialed.
You can select extra options if you access the call
logs Æ page 24.
16
Making Calls – Enhanced Functions
Step by Step
Dialing from the Phone Book
Prerequisite: The phone book must contain entries,
see Æ page 20.
Off-Hook Dialing
Press this key.
A d a m
G r e e n
Ø
2 2 9 3 0 9 4 4 5
Press
to select the number you want to call. The
name is displayed on the first line and the phone number on the second.
or p Press the digit keys to enter the first letters of the subscriber’s name. For more information on character input, see Æ page 51.
P e t e r
J o h n s o n
Ú
2 8 8 3 0 4 2 8 3
Press
aled.
to confirm your selection. The number is di-
On-Hook Dialing
Press this key.
A d a m
G r e e n
2 2 9 3 0 9 4 4 5
Ø
Press
to select the number you want to call. The
name is displayed on the first line and the phone number on the second.
or p Press the digit keys to enter the first letters of the subscriber’s name. For more information on character input, see Æ page 51.
n Lift the handset. The number is dialed.
17
Making Calls – Enhanced Functions
Step by Step
During a Call
3-Way Conference
The "3-Way Conference" feature must be activated, see Æ page 40.
In a conference call, you can talk to as many as two other parties at the same time.
Prerequisite: You are conducting a call.
Press this key.
D i a l
N u m b e r
Dial the number of the other conference participant. Announce the conference.
3 2 3 4 9 3 4 0 _
Press this key. You are connected to both subscribers.
3 2 3 4 9 3 4
C o n f e r e n c e
Ú
0 5 : 0
Press
to scroll through the list of participants. The
subscribers and the time they joined the conference are
shown on the display.
Call Transfer
The "Call Transfer" feature must be activated, see
Æ page 41.
If the person you are speaking to wants to talk to another colleague of yours, you can transfer the call that colleague.
Quick Transfer (Unscreened Transfer)
Prerequisite: You are conducting a call.
Press this key.
D i a l
N u m b e r
Enter the other subscriber’s number.
3 2 3 4 9 3 4 0 _
t Replace the handset. The call is transferred.
If the other subscriber is busy or does not answer, your
telephone is called back after a certain interval. When
you lift the receiver, you are reconnected to the party on
hold.
18
Making Calls – Enhanced Functions
Step by Step
Screened transfer
Prerequisite: You are conducting a call.
Press this key.
D i a l
N u m b e r
Enter the other subscriber’s number.
3 2 3 4 9 3 4 0 _
s Announce the call.
t Replace the handset. The call is transferred.
19
Making Calls – Enhanced Functions
Step by Step
Editing the Phone Book
You can save, edit, and delete names and telephone
numbers in a phone book. You can also transfer phone
numbers from call logs Æ page 25.
Adding an Entry to a Phone Book
Press this key.
N o
E n t r i e s
C r e a t e
If there are no entries, press
tion.
E n t r y ?
to confirm your selec-
or
A d a m
Ø
G r e e n
2 2 9 3 0 9 4 4 5
P h o n e
B o o k
1 . N e w
E n t r y
N am e :
Ø
>A b c
P e t e r _
N u m b e r :
Press
to confirm your selection.
Enter the name. For more information on character input, see Æ page 51.
Press
to confirm your selection.
2 8 8 3 0 4 _
Enter the phone number. Press
lection.
P e t e r
The entry is saved in the phone book.
S a v e d
20
The first entry (name and phone number) is displayed.
Press
to confirm your selection.
J o h n s e n
to confirm your se-
Making Calls – Enhanced Functions
Step by Step
Editing a Telephone Book Entry
Press this key.
A d a m
Ø
G r e e n
The first entry (name and phone number) is displayed.
2 2 9 3 0 9 4 4 5
or
Press these keys to scroll through the phone book list.
or p Press the digit keys to enter the first letters of the subscriber’s name. For more information on character input, see Æ page 51.
P e t e r
J o h n s o n
Ú
2 8 8 3 0 4 2 8 3
P h o n e
B o o k
2 . E d i t
N am e :
P e t e r
Ú
E n t r y
>A b c
J e f f e r s o n
N u m b e r :
The entry you want to delete is displayed.
Press
to confirm your selection.
Use
to scroll to the function displayed and press
to confirm it.
Edit the name. For more information on character input,
see Æ page 51.
Press
to confirm your selection.
2 8 8 3 0 3 4 0 _
Edit the phone number. Press
tion.
P e t e r
Your changes to the phone book entry are saved.
J e f f e r s o n
to confirm your selec-
S a v e d
21
Making Calls – Enhanced Functions
Step by Step
Deleting a Phone Book Entry
Press this key.
A d a m
Ø
G r e e n
The first entry (name and phone number) is displayed.
2 2 9 3 0 9 4 4 5
or
Press these keys to scroll through the phone book list.
or p Press the digit keys to enter the first letters of the subscriber’s name. For more information on character input, see Æ page 51.
P e t e r
J o h n s o n
Ú
2 8 8 3 0 4 2 8 3
P h o n e
B o o k
3 . D e l e t e
E n t r y
Ú
D e l e t e
The entry you want to delete is displayed.
Press
to confirm your selection.
Use
it.
to scroll to a function and press
to confirm
Press
to confirm your selection. The phone book entry is permanently deleted.
O K ?
Deleting all Phone Book Entries
This function permanently deletes all phone book
entries.
Press this key.
A d a m
G r e e n
Ø
2 2 9 3 0 9 4 4 5
P h o n e
B o o k
4 . D e l e t e
D e l e t e
O K ?
22
A l l
Ú
The first entry (name and phone number) is displayed.
Press
to confirm your selection.
Use
it.
to scroll to a function and press
to confirm
Press
to confirm your selection. All phone book entries are permanently deleted.
Making Calls – Enhanced Functions
Step by Step
Using the Call Log
All calls are recorded in call logs. The following call types
are saved in different call logs:
• missed calls (not received)
• received calls
• dialed numbers
You can also edit call log entries via the WebBased Management tool, see Æ page 41.
Displaying Missed Calls
Press this key.
M a i n
M e n u
1 . C a l l
C a l l
L o g
Ø
L o g
Ø
1 . M i s s e d
0 2 = 2 2 2 8 7 5 8 8
1 0 : 0 4
2 8 . 1 0 .
Ú
Press
to confirm your selection.
Press
to confirm your selection.
If several entries are available, press
to select the required entry. The caller’s phone number is displayed on
the first line; the time and the date of the missed call is
displayed on the second line.
Displaying Received Calls
Press this key.
M a i n
M e n u
1 . C a l l
C a l l
L o g
Ø
L o g
2 . R e c e i v e d
Ú
0 4 = 2 8 8 3 7 4 5 6
1 8 : 3 3
2 8 . 1 0 .
Ú
Press
Use
it.
to confirm your selection.
to scroll to a function and press
to confirm
If several entries are available, press
to select the required entry. The caller’s phone number is displayed in
the first line; the time and the date of the call is displayed in the second line.
23
Making Calls – Enhanced Functions
Step by Step
Displaying Dialed Numbers
Press this key.
M a i n
M e n u
1 . C a l l
C a l l
Ø
L o g
L o g
3 . D i a l e d
Ú
N o s .
0 3 = 1 8 8 2 9 3 0 5 4
1 2 : 0 7
2 8 . 1 0 .
Ú
Press
Use
it.
to confirm your selection.
to scroll to a function and press
to confirm
If several entries are available, press
to select the required entry. The dialed phone number is displayed on
the first line; the time and the date that the number was
dialed is displayed on the second line.
Dialing a Phone Number from the Call Log
You can select an entry in any call log to dial the corresponding phone number. This is illustrated in the following using a missed call as an example.
Press this key.
M a i n
M e n u
1 . C a l l
C a l l
Ø
L o g
L o g
Ø
1 . M i s s e d
0 2 = 2 2 2 8 7 5 8 8
1 0 : 0 4
2 8 . 1 0 .
Ú
Press
to confirm your selection.
Press
to confirm your selection.
If several entries are available, press
quired entry.
n Lift the handset. The number is dialed.
24
to select the re-
Making Calls – Enhanced Functions
Step by Step
Transferring a Phone Number to the Phone
Book
You can select an entry in any call log and transfer the
corresponding phone number to the phone book. This
is illustrated in the following using a missed call as an
example.
Press this key.
M a i n
M e n u
1 . C a l l
C a l l
Ø
L o g
L o g
Ø
1 . M i s s e d
0 2 = 2 2 2 8 7 5 8 8
1 0 : 0 4
2 8 . 1 0 .
Ú
0 2 = 2 2 2 8 7 5 8 8
1 . S a v e
t o
D i r .
Ø
Press
to confirm your selection.
Press
to confirm your selection.
If several entries are available, press
to select the required entry. Press
to confirm your selection.
Press
to confirm your selection.
To complete the process, proceed as described for editing a phone book entry Æ page 21.
Deleting a Phone Number from the Call Log
You can delete individual entries from call logs. This is
illustrated in the following using a missed call as an example.
Press this key.
M a i n
M e n u
1 . C a l l
C a l l
L o g
Ø
L o g
Ø
1 . M i s s e d
0 2 = 2 2 2 8 7 5 8 8
1 0 : 0 4
2 8 . 1 0 .
to confirm your selection.
Press
to confirm your selection.
Ú
If several entries are available, press
to select the required entry. Press
to confirm your selection.
Ú
Use
it.
0 2 = 2 2 2 8 7 5 8 8
2 . D e l e t e
Press
to scroll to a function and press
to confirm
25
Making Calls – Enhanced Functions
Step by Step
Deleting Entries in All Call Logs
This function permanently deletes all entries in all
call logs.
Press this key.
M a i n
M e n u
1 . C a l l
C a l l
L o g
Ø
L o g
4 . D e l e t e
D e l e t e
A l l
Ú
A l l
Press
Use
it.
Press
to confirm your selection.
to scroll to a function and press
to confirm
to confirm your selection.
O K ?
Accessing the Voice Mail
A voice mail server must be configured for this
purpose. If you have any questions or problems,
contact the relevant service personnel.
Press this key.
M a i n
M e n u
2 . V o i c e
M a i l
Ú
Press
to make a selection.
n Lift the handset. The voice mail server is dialed. You can
listen to saved voice messages.
26
Configuration
Step by Step
Configuration
Configuring Call Forwarding
You can configure call forwarding for the following scenarios:
• no answer (CFNR)
• on busy
• always (unconditional)
You can activate/deactivate forwarding and configure a
forwarding destination for each scenario.
The following describes how to configure forwarding on
busy. The same procedure is used for both of the other
forwarding types.
Activating and Deactivating Forwarding
Press this key.
M a i n
M e n u
3 . F o r w a r d
Ú
1 . N o
Ø
A n s w e r
O f f
Use
it.
to scroll to a function and press
to confirm
The current status of the forwarding type is indicated.
For a detailed explanation, see Æ page 40.
or
2 . O n
B u s y
Ú
O f f
Press
to make a selection.
For a detailed explanation, see Æ page 40.
or
3 . A l w a y s
Ú
O f f
3 . A lw a y s
Ú
Press
to make a selection.
For a detailed explanation, see Æ page 40.
Press
to activate unconditional forwarding.
O n
if necessary
Press this key repeatedly to toggle the options once
again.
27
Configuration
Step by Step
Configuring Forwarding Destinations
Example: forwarding on busy
Press this key.
M a i n
M e n u
Ú
3 . F o r w a r d
2 . F o r w a r d
Ú
t o
2 2 2 8 7 5 8 8
E d i t :
Use
to scroll to the function displayed and press
to confirm it.
Press
to make a selection. If a destination has already been configured for forwarding on busy, this is indicated on the display. Press
to confirm your selection.
The cursor is positioned at the end of the destination
number.
2 2 2 8 7 5 8 8 _
Press this key to delete digits.
p Enter digits via the keypad.
Confirm to save your changes.
Activating and Deactivating Don’t Disturb
Press this key.
M a i n
M e n u
4 . D o n ’ t
D o n ’ t
d i s t u r b
Ú
Use
to scroll to the function displayed and press
to confirm it.
d i s t u r b
The current status of this feature is indicated.
d i s t u r b
Press
O n
D o n ’ t
to deactivate this feature.
O f f
if necessary
28
Press this key repeatedly to toggle the options once
again.
Configuration
Step by Step
Configuring Properties
Configuring the Date Format
For a detailed explanation, see Æ page 42
Press this key.
M a i n
M e n u
Ú
5 . S e t u p
S e t u p
1 . U s e r
S e t t i n g s
Ø
1 . D a t e
F o r m a t
Ø
Use
to scroll to the function displayed and press
to confirm it.
Press
to confirm your selection.
M M . D D . Y Y
The current format is displayed. A date may be displayed in the following format, for instance: "10.28.05".
Press
to confirm your selection.
1 . D a t e
Press
F o r m a t
to confirm your selection.
M o d i f y ?
1 . D a t e
F o r m a t
Ú
Y Y . M M . D D
Press
to make a selection. A date is now displayed
in the following format, for example: "05.10.28".
or
1 . D a t e
F o r m a t
×
D D . M M . Y Y
if necessary
or
Press
to make a selection. A date is now displayed
in the following format, for example: "28.10.05".
Press these keys to switch between the options.
Confirm to save your changes.
29
Configuration
Step by Step
Configuring the Time Format
For a detailed explanation, see Æ page 45.
Press this key.
M a i n
M e n u
Ú
5 . S e t u p
S e t u p
1 . U s e r
S e t t i n g s
Ø
2 . T i m e
F o r m a t
Ú
1 2
H o u r ( s )
2 . T i m e
2 4
F o r m a t
Ú
H o u r ( s )
if necessary
or
Use
to scroll to the function displayed and press
to confirm it.
Press
to confirm your selection.
Press
to make a selection. The current format is displayed. The time is displayed in the following format,
for example: "02:36pm".
Press
.
The time is displayed in the following format, for
example: "14:36".
Press these keys to switch between the options.
Confirm to save your changes.
Setting a Language
For a detailed explanation, see Æ page 43.
Press this key.
M a i n
M e n u
Ú
5 . S e t u p
S e t u p
1 . U s e r
S e t t i n g s
3 . L a n g u a g e
Ø
Ú
E n g l i s h
3 . L a n g u a g e
Ú
Use
to scroll to the function displayed and press
to confirm it.
Press
to confirm your selection.
Press
to make a selection. The current language is
displayed. Press
to confirm your selection.
Press
to confirm your selection.
M o d i f y ?
3 . L a n g u a g e
G e r m a n
30
Ú
Press
to make a selection. The language is changed
to German.
Configuration
Step by Step
if necessary
or
Press these keys to switch between the options.
Confirm to save your changes.
Setting a Country
For a detailed explanation, see Æ page 41.
Press this key.
M a i n
M e n u
Ú
5 . S e t u p
S e t u p
1 . U s e r
S e t t i n g s
Ø
Ú
4 . C o u n t r y
Use
to scroll to the function displayed and press
to confirm it.
Press
to confirm your selection.
G e r m a n y
Press
to make a selection. The current country is
displayed. Press
to confirm your selection.
4 . C o u n t r y
Press
to confirm your selection.
Press
to make a selection. The country is set to US.
M o d i f y ?
4 . C o u n t r y
Ú
U S
if necessary
or
Press these keys to switch to further options.
Confirm to save your changes.
Setting the Ringer
For a detailed explanation, see Æ page 45
Press this key.
M a i n
M e n u
Ú
5 . S e t u p
S e t u p
1 . U s e r
S e t t i n g s
5 . R i n g e r
M e l o d y
1
Ø
Ú
Use
to scroll to the function displayed and press
to confirm it.
Press
to confirm your selection.
Press
to make a selection. The current ringer is displayed. Press
to confirm your selection.
31
Configuration
Step by Step
5 . R i n g e r
Press
to confirm your selection.
M o d i f y ?
5 . R i n g e r
M e l o d y
Ú
1
if necessary
or
Press
to make a selection. The ringer is set to
"Melody 1".
Press these keys to switch between the options.
Confirm to save your changes.
Configuring Voice Mail
Press this key.
M a i n
M e n u
Ú
5 . S e t u p
S e t u p
1 . U s e r
S e t t i n g s
6 . V o i c e
M a i l
Ø
Ú
2 2 2 8 1 0 0 1
E d i t :
Use
to scroll to the function displayed and press
to confirm it.
Press
to confirm your selection.
Press
to make a selection. The current voice mail
destination number is displayed. Press
to confirm
your selection.
The cursor is positioned at the end of the voice mail
destination number.
2 2 2 8 1 0 0 1 _
Press this key to delete digits.
p Enter digits via the keypad.
Confirm to save your changes.
Displaying the Current Status
For a detailed explanation, see Æ page 43.
Press this key.
M a i n
m e n u
6 . S t a t u s
Ú
Use
to scroll to the function displayed and press
to confirm it.
1 . M A C
Ø
The device’s MAC address is displayed.
A d d r e s s
0 0 9 0 9 6 - 1 1 2 2 3 3
32
Configuration
Step by Step
2 . I P
A d d r e s s
Ú
Press
to make a selection. The current IP address
is displayed.
Ú
Press
to make a selection. The current software
versions are displayed.
The xxxx/yyyy/zz syntax corresponds to:
xxxx = boot loader version
yyyy = application version
zz = hardware version
Ú
Press
to make a selection. The current telephone
number is displayed.
0 1 0 . 0 0 1 . 0 2 9 . 1 6 7
3 . V e r s i o n
0 0 0 1 / 0 0 0 1 / 0 1
4 . P h o n e
N u m b e r
0 5 0 9 9 9 9 1 0 0 1
33
Web-Based Management Tool
Web-Based Management Tool
General Information
optiPoint 150 S is equipped with a Web server, which enables information
from the telephone to be mapped to a Web browser on a PC integrated
into the LAN (Web-based Management Tool).
The IP data for the optiPoint 150 S and the PC
must be configured correctly for this.
The Wed-based Management Tool contains the following form elements:
home Click this link to obtain information about your optiPoint 150 S, see
Æ page 36.
logout Click this link to access the home page, see Æ page 35.
Click Clear to reset the changes in the current form to the former
optiPoint 150 S values.
Click Save to incorporate the changes into the current form. This transfers
the changes to the optiPoint 150 S.
???Click this button to perform an action (such as, Confirm, Delete, Edit,
Add, Delete All or Browse).
Enter a value in the input field.
Select an entry from the list field.
Select the relevant option radio button.
Activate a checkbox to enable or disable a function.
34
Web-Based Management Tool
Preparatory Steps
Opening the Home Page
To invoke the interface, open a Web browser and enter the following URL:
http://[telephone IP]
Here, [telephone IP] is the IP address of the optiPoint 150 S you want to
map.
The home page appears:
35
Web-Based Management Tool
User Setup Dialog
The user setup dialog must be configured in the system. Contact the
service personnel for your user name and password.
Details on configuring a user account and the default values for the
administration account can be found in the optiPoint 150 S Administration Manual at:
http://www.siemens.de/hipath.
1. Enter your user name for the user setup dialog in the User Name field,
see Æ page 46.
2. Enter your user password in the Password field, see Æ page 43.
3. Click Login.
Structure
•
•
User Setup Æ page 37
– Localization Æ page 37
– Call Features Æ page 37
– Audio SettingsÆ page 37
Utilities Æ page 38
– Phone Book Æ page 38
– Call Logs Æ page 38
– Backup Settings Æ page 39
– System Æ page 39
Information
Click a field in one of the interface images to obtain more information about the field.
36
Web-Based Management Tool
User Setup
Click a field in one of the interface images to obtain more information about the field.
Localization
Call Features
Audio Settings
37
Web-Based Management Tool
Utilities
Click a field in one of the interface images to obtain more information about the field.
Phone Book
Call Logs
38
Web-Based Management Tool
Backup Settings
System
39
Parameter Description
Parameter Description
This glossary is sorted alphabetically and provides a description of all parameters in your optiPoint 150 S.
There are two ways of configuring your phone:
•
via the phone
•
via the Web-based Management Tool
3-Way Conference
• On radio button: Activate this option if you want to convert a consultation call into a three-way conference. This kind of conference is also referred to as "local conferencing".
• Off radio button: Activate this option if you want to transfer a consultation call to a colleague.
Æ page 18
Æ page 37
Backup your Current Settings
• You can save your optiPoint 150 S configuration settings (data backup).
• Proceed as follows to back up the data:
1. Click Save.
2. Select the directory to which the backup should be saved.
3. Click Save.
Æ page 39
Call Forward Always
• Activate this checkbox if you want to forward incoming calls immediately to another destination. This is a useful function if you are going to
be unavailable for a long period of time (for example, on vacation).
• Enter the phone number to which your calls should be forwarded.
Æ page 27
Æ page 37
Call Forward on Busy
• Activate this checkbox if you want to forward incoming calls while you
are on a call. This is a useful function that enables callers to reach a contact person (for example, customer service).
• Enter the phone number to which your calls should be forwarded.
Æ page 27
Æ page 37
Call Forward No Answer
• Activate this checkbox if you want to forward incoming calls to another
destination after a certain time has elapsed. This is a useful function if
you are unable to accept incoming calls on a regular basis (for example,
while participating in meetings).
• Enter the phone number to which your calls should be forwarded.
• Enter the period (in seconds) after which calls should be forwarded.
Æ page 27
40
Æ page 37
Parameter Description
Call Logs
• You can select the following call logs:
– Missed Call(s) radio button: Missed Calls
– Received Call(s) radio button: received calls
– Dialed Call(s) radio button: dialed numbers
• Activate the checkbox for the entry you want to edit.
• You can select the following buttons:
– Delete: Deletes the selected entry.
– Save: Saves the selected entry.
– Delete All: Deletes all entries permanently.
Æ page 23
Æ page 38
Call Transfer
• On radio button: Activate this option if you want to transfer a consultation call after announcement.
• Off radio button: Activate this option if you want to transfer a consultation call without announcement.
Æ page 18
Æ page 37
Call Waiting
• On radio button: Activate this option if you want to accept a second
call. The caller hears the on-hook signal, you hear the call waiting signal.
• Off radio button: Activate this option if you do not want to accept any
other calls while already on a call.
Æ page 15
Æ page 37
Country
• Select the country where you will be operating your optiPoint 150 S
from the list.
• You can select the following countries:
– US
– Germany
– France
– Italy
– Spain
– Austria
– Switzerland
– Belgium
– UK
– Argentina
– Brazil
– Luxembourg
– Netherlands
– Portugal
Æ page 31
Æ page 37
41
Parameter Description
Date Format
• Select the format in which you want the date to appear on the display.
• You can select the following formats:
– MM.DD.YY (month.day.year)
– YY.MM.DD (year.month.day)
– DD.MM.YY (day.month.year)
Æ page 29
Æ page 37
Daylight Saving
• On radio button: Activate this option if you do not want the display to
light up.
• Off radio button: Activate this option if you want the display to light up
when you lift the handset.
Æ page 37
Do Not Disturb
• On radio button: Activate this option if you do not want incoming calls
to be signaled. The calling party then hears a busy signal (the called party is not disturbed). The calling party cannot initiate a callback in this
case.
• Off radio button: Activate this option if you want to signal incoming
calls by the ringer and display.
Æ page 28
Æ page 37
Get PhoneBook Settings
• You can save your phone book (data backup).
• Proceed as follows to back up the data:
1. Click Save.
2. Select the directory to which the backup should be saved.
3. Click Save.
Æ page 39
Handset Volume
• Select the receiving volume value for the handset from the list.
• You can select the following values:
– 0 (quiet)
– to
– 7 (loud)
Æ page 14
42
Æ page 37
Parameter Description
Information
• Displays information on the status of your telephone.
– System Up Time: Show how long your optiPoint 150 S has been operating.
– NTP Time: Displays the SIP server time.
– IP Address: Displays the IP address of your optiPoint 150 S.
– MAC Address: Displays the MAC address of your optiPoint 150 S.
– Application Version: Displays the phone software version. This status contains information on the scope of functions available on your
optiPoint 150 S and may change when updating the telephone software.
– Downloader Version: The xxxx/yyyy/zz syntax corresponds to:
xxxx = boot loader version
yyyy = application version
zz = hardware version
– SIP Status: Displays the status of the SIP server connection.
OK: Success
Error: Server not responding
– Phone Number: Displays the phone number of your optiPoint 150 S.
Æ page 32
Æ page 36
LCD Language
• Select the display language from the list.
• You can select the following languages:
– German
– English
Æ page 30
Æ page 37
SpeakerVolume
• Select the receiving volume value for the loudspeaker from the list.
• You can select the following values:
– 0 (quiet)
– to
– 7 (loud)
Æ page 14
Æ page 37
New User Login ID
• Enter the user name required to access the user setup dialog, see
Æ page 35.
Æ page 39
New User Password
• Enter your new password in this field.
Æ page 39
Password
• Enter your user password for accessing the Web-based Management
Tool in this field, see Æ page 35.
43
Parameter Description
Æ page 35
Phone Book
• Activate the checkbox for the phone book you want to edit.
• You can select the following buttons:
– Delete: Deletes an entry from the phone book.
– Edit: Modifies an entry in the phone book.
– Add: Adds an entry to the phone book.
– Delete All: Deletes all entries in the phone book.
Æ page 20
Æ page 38
Privacy level
• Prerequisite: The checkbox under "Set PRIVACY" must be activated,
see Æ page 45.
• Activate the appropriate checkbox to select the security level for voice
transmission:
– None: No security level.
– Header: High security level.
– Session: Medium security level.
– Critical: Low security level.
This function is not supported by all communication platforms. Contact the
service personnel for information on the availability of this function.
Æ page 37
Restore to Previous Settings
• This function allows you to restore the original configuration setting (data retrieval).
• Prerequisite: A backup of the configuration must be available, see
Æ page 40.
• Proceed as follows to retrieve the data:
1. Click Browse.
2. Select the backup file from the corresponding directory.
3. Click Confirm.
Æ page 39
Retype New User Password
• Re-enter your new user password in this field, see Æ page 43.
Æ page 39
44
Parameter Description
Ringer
• Select the melody for the ring tone for your optiPoint 150 S from this
list.
• You can choose from 16 melodies:
– Melody 1
– to
– Melody 16
Æ page 31
Æ page 37
Ringer Volume
• Select a value for the ringer volume for your optiPoint 150 S.
• You can select the following values:
– 0 (mute)
– to
– 7 (loud)
Æ page 14
Æ page 37
Set PRIVACY
• Activate this checkbox to enable a security level, see Æ page 44.
Æ page 37
Start PhoneBook Restore
• This function allows you to load an existing phone book (data retrieval).
• Prerequisite: A backup of your phone book data must be available,
see Æ page 42.
• Proceed as follows to retrieve the data:
1. ???Click Browse.
2. Select the backup file from the corresponding directory.
3. Click Confirm.
Æ page 39
Time Format
• Select the time format for the time display from the list.
• You can select the following formats:
– 12 Hours
– 24 Hours
Æ page 30
Æ page 37
45
Parameter Description
Time Server
• On radio button: Activate this option if a server is available for setting
the time (NTP server = Network Time Protocol server). The IP address
of the time server must be entered, see Æ page 46.
• Off radio button: Activate this option if a server is not available for setting the time. The settings for "Time Zone", "Date Format", and "Time
Format" must be made by hand.
Æ page 37
Time Server Address
• Enter the IP address of the time server here (NTP server = Network
Time Protocol server). The time server must be activated, see
Æ page 46.
Æ page 37
Time Zone
• Select the time zone of the country where the telephone is operated in
this list.
• You can select the following values:
– GMT -12:00
– to
– GMT +12:00
Æ page 37
User Name
• Enter the user name required to access the user setup dialog.
Æ page 35
Voice Mail
• Enter the IP address of the voice mail server in this field.
Æ page 37
46
Documentation
A PDF version of this operating manual is available on the Internet at
http://www.siemens.com/hipath
A CD-ROM containing HTML and PDF versions is also available (ask your
service personnel).
In order to look at and print the operating manual in PDF format, you need
a computer on which the free Adobe Acrobat Reader software package is
installed.
To display the HTML manual, you need a computer with a Web browser,
for example, Microsoft Internet Explorer.
47
Fixing Problems
Fixing Problems
Caring for Your Telephone
•
•
•
Always use a damp or antistatic cloth to clean the telephone. Never
use a dry cloth.
If the handset is heavily soiled, clean it with a diluted surfactant-based
neutral cleaner, such as, Pril dishwashing detergent. Afterwards remove all traces of the cleaner with a damp cloth (using water only).
Do not use alcohol-based or corrosive cleaners or abrasive powders.
Troubleshooting
Pressed key does not respond:
Check whether the key is stuck.
The time displayed is incorrect:
If a time server Æ page 46 is configured, the time automatically corrects
itself at regular intervals.
If a time server is not installed, the Web-Based Management tool
Æ page 34 can be used to correct the time.
To correct any other problem:
First contact your service personnel. If the service personnel are unable to
correct the problem, contact Customer Service.
48
Fixing Problems
Step by Step
Display Messages
System Start
I n i t i a l i z i n g
.
A c q u i r i n g
.
S I P
I P
R e g i s t e r i n g
R e s t a r t i n g
The telephone is connected to the power supply. Displays information on the initialization of the telephone.
The telephone requests an IP number from the DHCP
server.
. The telephone registers at the SIP provider.
.
The telephone is restarting.
Software Upgrade
S o f t w a r e
U p g r a d e
3 5 7 8 0 0 5
The telephone software is upgrading. A progress bar indicates the remaining data volume (in bytes) to be transferred.
Forwarding
Unconditional forwarding
F o r w a r d
2 2 2 8 7 5 8 8
t o
.
Unconditional forwarding is activated. Displays the destination number for unconditional forwarding.
Voice Mail
Displays the number of new voice messages received
in your voice mail.
0 8 : 2 8 p m
3
n e w
0 2 . 0 7 . 0 5
M e s s a g e s
First line: Time and date.
Second line: Number of new voice messages.
Missed Calls
Displays the number of missed calls.
0 8 : 2 8 p m
2
m i s s e d
0 2 . 0 7 . 0 5
C a l l s
First line: Time and date.
Second line: Number of missed calls.
49
Fixing Problems
Step by Step
Idle Mode
0 8 : 2 8 p m
0 2 . 0 7 . 0 5
3 2 3 4 9 3 4 0
First line: Time and date.
Second line: User’s own number.
During a Call
n User answers the incoming call.
Lift the handset.
2 2 2 8 7 5 8 8
00:15
First line: Phone number (if the phone number is stored
in the phone book, the name is displayed).
Second line: Call duration (mm:ss). If the call duration
exceeds 59:59, the telephone resets the value to 00:00.
On Busy
B u s y
2 2 2 8 7 5 8 8
50
First line: "Busy" - the line is busy.
Second line: Phone number (if the phone number is
stored in the phone book, the name is displayed).
Fixing Problems
Step by Step
Character Input
Letters and digits are entered by pressing the dial keys
an appropriate number of times. This also applies when
entering alphanumeric passwords.
Example: "+" = press the q key twice.
Key
1x
e [1]
f a
g d
h g
i j
j m
k p
l t
m w
d .
q r [2]
2x 3x
4x 5x
6x 7x
8x 9x 10x
1
b
c
2
ä
e
f
3
h
i
4
k
l
5
n
o
6
ö
q
r
s
7
u
v
8
ü
x
y
z
9
,
0
+
&
(
)
’
@
:
#
*
1)
Space.
2)
Switches between upper case (next letter only), lower case and
digit input for alphanumeric character input.
Deleting characters
Press this key to delete characters to the left of the cursor.
Inputting alphanumeric characters
Press
in character input mode (for entering subscriber names, for instance) to switch between different editor modes (see also table above).
N am e :
P e t e r _
>A b c
The current editor mode is shown in the top right corner
of the display. The display can be set to: ">Abc" (upper
case), "abc" (lower case) and "123" (digit input).
51
Fixing Problems
Step by Step
Contacts in the Case of Problems
If you encounter a disruption that lasts longer than five
minutes, for example, contact the relevant service personnel.
52
Index
Index
A
Accessing voice mail 26
Activating the software test display 33
Adjusting the ring volume 14
C
Call forwarding
activating/deactivating 27
configuring a destination 28
display 49
Call log
calling back missed calls 16, 24
deleting entries
dialing a phone number 24
displaying dialed numbers 24
displaying missed calls 23
displaying received calls 23
entry
deleting 25
transferring to phone book
25
Call transfer
with announcement 19
without announcement 18
Call waiting 15
Caring for your telephone 48
Conference 18
Configuration
country 31
date format 29
language 30
ringer 31
time format 30
voice mail destination number 32
Configuring a country 31
Contact 52
D
Dialing
from the phone book 17
manual 12
using redial 13
Dialing the last number dialed 16
Display
call forwarding 49
configuring the date format 29
configuring the time format 30
during a call 50
during telephone startup 49
idle mode 50
while called party is busy 50
Displaying messages 26
Displaying the status 32
Don’t disturb
activating/deactivating 28
E
Echo effect 8
F
Format
configuring the date display 29
configuring the time display 30
H
HTML format 47
M
Making a consultation call (call waiting) 15
Making calls 12
Malfunctions 48
Messages 49
Microphone, deactivating 11
Mute 11
N
NTP (Network Time Protocol) 46
O
Open listening 11
Open listening during a call 11
operating instructions
HTML format 47
ordering 47
PDF format 47
53
Index
P
33
configuring a destination ....................... 28
display ...................................................... 49
Call log
calling back missed calls ................. 16, 24
deleting entries
all ........................................................... 26
individual .............................................. 25
dialing a phone number ......................... 24
displaying dialed numbers .................... 24
displaying missed calls .......................... 23
displaying received calls ....................... 23
entry
deleting ................................................ 25
transferring to phone book ............... 25
Call transfer
with announcement ............................... 19
without announcement ......................... 18
Call waiting .................................................. 15
Caring for your telephone ......................... 48
Conference .................................................. 18
Configuration
country ..................................................... 31
date format .............................................. 29
language .................................................. 30
ringer ........................................................ 31
time format .............................................. 30
voice mail destination number ............. 32
Configuring a country ................................ 31
Contact ......................................................... 52
T
D
PDF format 47
Phone book
deleting entries
all 22
individual 22
dialing from 17
entry
adding 20
deleting 22
editing existing 21
transferring from call log 25
R
Reboot 33
Redialing a number 13
last phone number dialed 16
Restarting the telephone 33
Ringer, setting 31
S
Setting a language 30
Setting the handset volume 14
Setting the speaker volume 14
Switching the software test display on/off
Telephone, muting 11
Troubleshooting 48
W
Web-Based Management Tool 34
A
Accessing voice mail ................................. 26
Adjusting the ring volume ........................ 14
C
Call forwarding
activating/deactivating ........................... 27
54
Dialing
from the phone book ............................. 17
manual ...................................................... 12
using redial .............................................. 13
Dialing the last number dialed ................. 16
Display
call forwarding ........................................ 49
configuring the date format .................. 29
configuring the time format .................. 30
during a call ............................................. 50
during telephone startup ....................... 49
idle mode ................................................. 50
while called party is busy ...................... 50
Displaying messages ................................ 26
Displaying the status ................................. 32
Don’t disturb
Index
editing existing .................................... 21
transferring from call log ................... 25
activating/deactivating ........................... 28
E
Echo effect .................................................... 8
R
F
Redialing a number .................................... 13
last phone number dialed ..................... 16
Ringer, setting ............................................ 31
Format
configuring the date display ................. 29
configuring the time display ................. 30
H
HTML format .............................................. 47
M
Making a consultation call (call waiting) . 15
Making calls ................................................ 12
Malfunctions ............................................... 48
Messages .................................................... 49
Microphone, deactivating ......................... 11
Mute ............................................................. 11
S
Setting a language ..................................... 30
Setting the handset volume ..................... 14
Setting the speaker volume ..................... 14
T
Telephone, muting ..................................... 11
Troubleshooting .......................................... 48
W
Web-Based Management Tool ................ 34
N
NTP (Network Time Protocol) .................. 46
O
Open listening ............................................ 11
Open listening during a call ...................... 11
operating instructions
HTML format .......................................... 47
ordering .................................................... 47
PDF format .............................................. 47
P
PDF format .................................................. 47
Phone book
deleting entries
all ........................................................... 22
individual .............................................. 22
dialing from ............................................. 17
entry
adding ................................................... 20
deleting ................................................ 22
55
Menu Functions
Menu Functions
Press the "Program/Service" key. Use
and
to select functions. Menu items for
administrative settings with password entry are not displayed:
Main menu
1 Call Log
2 Voice Mail
3 Forward
4 Don’t disturb
1
2
3
4
0
Missed
Received
Dialed Nos.
Delete All
Exit
1
1
2
2
3
3
0
No Answer
Forward to
On Busy
Forward to
Always
Forward to
Exit
5 Setup
1 User Settings
0 Exit
6 Status
1
2
3
4
0
0 Exit
MAC Address
IP Address
Version
Phone Number
Exit
1
2
3
4
5
6
0
Date Format
Time Format
Language
Country
Ringer
Voice Mail
Exit
RFC Standards
RFC Standards
The following table provides an overview of RFC (Request For Comment) standards that
are compatible with optiPoint 150 S.
This overview is not exhaustive.
RFC
Description
RFC3261
Session Initiation Protocol (SIP)
RFC2976
The SIP INFO Method
RFC3265
Session Initiation Protocol (SIP) Specific Event Notification
RFC3311
The Session Initiation Protocol (SIP) UPDATE Method
RFC3323
A Privacy Mechanism for the Session Initiation Protocol (SIP)
RFC3428
Session Initiation Protocol (SIP) Extension for Instant Messaging
RFC3515
The Session Initiation Protocol (SIP) Refer Method
RFC3842
A Message Summary and Message Waiting Indication Event Package for the
Session Initiation Protocol (SIP)
RFC3262
Reliability of Provisional Responses in the Session Initiation Protocol (SIP)
RFC3665
Session Initiation Protocol (SIP) Basic Call Flow Examples
RFC3489
STUN - Simple Traversal of User Datagram Protocol (UDP) Through Network
Address Translators (NATs)
RFC1889
RTP Real Time Protocol
RFC2327
SDP: Session Description Protocol
RFC3264
An Offer/Answer Model with Session Description Protocol (SDP)
RFC2833
RTP Payload for DTMF Digits, Telephony Tones and Telephony Signals
RFC3389
Real Time Transport Protocol (RTP) Payload for Comfort Noise (CN)
RFC3550
RTP A Transport Protocol for Real Time Applications
RFC3551
RTP Profile for Audio and Video Conferences with Minimal Control
RFC3555
MIME Type Registration of RTP Payload Formats
www.siemens.com/hipath
The information provided in this document contains merely general descriptions or characteristics of performance which in case of actual use
do not always apply as described or which may change as a result of further development of the products.
An obligation to provide the respective characteristics shall only exist if
expressly agreed in the terms of contract
The trademarks used are owned by Siemens AG or their respective owners.
© Siemens AG 2005
Siemens Communications
Hofmannstr. 51 • D-81359 Munich, Germany
Reference no.: A31003-A2056-L154-2-7619
Subject to availability. Right of modification reserved.
Printed in the Federal Republic of Germany.
29.08.06