- No category
advertisement
LEAPER-3C
HANDY FLASH WRITER
LEAPER-3C is specially designed for FLASH series, integrating powerful hardware and software to perform high quality . It is the best choice to program FLASH series device.
The most attraction of the LEAPER-3C is following
4T products policy, i.e. Light, Thin, Short, Tiny. Concerning the concept of environmental protection, the LEAPER-3C avoids unnecessary over-package.
LEAP is doing her responsibility for the earth.
Small, portable, light & usable with batteries
Stand-Alone FLASH programmer
Only one source is needed to copy with.
Two operation modes:stand-alone&PC mode
Support Windows 95/98/NT/2000/ME/XP
Display: LCD with 16 x 2 characters
Dimension 16cm 11cm 4.5cm
Weight 0.5Kgs
Temperature +5 to +45
Humidity up to 90 non-condensing
Altitude : up to 5000m
5 Function keys
Functions
Type
Blank check
Verify & check sum
Program
IC parameters are adjustable such as programming algorithm, Vpp voltage, and impulse width.
Meet CE requirement
Main unit
CD ROM (installation program and user's manual are included)
USB cable
12V/500mA power adaptor
Connect with PC by USB port to transmit data and execute functions such as :
Type/ Read/ Blank Check/ Program/Verify/Erase/
Disk/ Help/ Process/Parameter
C parameters are adjustable such as programming algorithm, Vpp voltage, and impulse width.
File formats supported:
Binary and machine code, Intel HEX , Motorola HEX
Various PLCC,TSOP,VSOP converters
EPROM
27C64- 27C080
EEPROM
28C256-28C040
FLASH EPROM
29C256-29C040
29EE/LE512-29EE/LE020
28F256-28F020A
28SF/VF 040
29F010-29F040
29F001-29F002
39SF/VF512-39SF/VF040
49F512-49BF040
49F/LV001-49F/LV002
○ ○
LEAP ELECTRONIC CO., LTD.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
FLASH Writer Devices List
27CXX
28FXX
28F010A 28F020 28F020A
AMD
AMIC
A290021T A29040 A29040A
ATMEL
BRIGHT
BM29F040
EON
EN29F040
FUJITSU
MBM29F040A
HYUNDAI
IMT
IM29F001T
MEGAWIN
MM29F040E
MOSEL
MXIC
MBM29F040C
IM29F002T
MM29LF040E
PERFECT
PDT29F010
PMC
ST
PE29F002N
M28W101 M28W201
SST
SYNCMOS
WINBOND
Standard Accessories
LEAPER-3C Flash Writer main unit x1, USB cable x1,
DC 12V/500mA adaptor x1, PC Software, drivers and manuals on CD-ROM x1
Main unit
Introduction
Unit top view
16X2 LCD display
Adaptor
IC package diagram
Master Textool
Function keys
DC 12V input socket
Slave Textool
USB cable
Unit back view
Power switch USB port (B type)
Textool handle
Battery compartment
Attention
1. It is preferred to use an internal USB port of your PC. External USB
ports are not recommended because of shared bandwidth and
possible compatibility issues of other USB devices.
2. In PC mode operation, the Slave textool is used for all operations.
In stand-alone mode, the source IC should be placed in the Master
textool and the target IC in the Slave textool.
Install software and driver
1. Set Font Size to [small fonts] (96 dpi) to have the optimal display.
1.1 Click the right button on the desktop. -> Select the [Properties] at the
bottom of the function menu.
1.2 Select [Settings] and then click the [Advanced] to set Font Size.
2. Install the software before connecting the Leaper-3C to the PC.
2.1 Insert the software CD into your CD-ROM drive. Normally the installation
program will start automatically (if Auto Run is enabled for your CD-drive).
Follow the instructions to complete
installation.
2.2 If Auto Run doesn't work, click [Setup.exe] in the CD directory to start the
installation.
3. Install the driver for the Leaper-3C hardware.
3.1 Make sure the Leaper-3C power is [OFF]. Connect the power adapter to
the Leaper-3C and a power outlet.
3.2 Connect the USB cable to PC USB port and to the programmer USB port.
3.3 Turn the Leaper-3C power to [ON]. Windows will now start the [Found
New Hardware Wizard].
3.4 Install Hardware Device Driver
-> Search for a suitable driver for my device (recommended)
3.5 Select Optional search locations
-> CD-ROM drives
3.6 Driver Files Search Result
-> Windows will find a driver for this device ...\driver\flashwriter.inf
3.7 Click [Finish] in the Found New Hardware Wizard
The Leaper-3C software and drivers have now been installed and the unit is ready for usage.
[3.3] [3.4]
LEAP Electronic Co., Ltd.
Tel : + 886-2-2999 1860
Fax : + 886-2-2999 9873 http : //www.leap.com.tw
Email: [email protected]
[3.5]
[3.6] [3.7]
Operation window
Programming source
Load from PC
Read from source IC
Verify source IC
Edit file
Save file
Exit program
Source file editing
8bits HEX display 16bits HEX display Buffer & file information
IC manufacturer, type number
Device verify
Check SUM
Progress bar
Erase
Blank check
Program
Verify
Program process & options
Protect / security
Select IC number 8/16/32 Bits
Stop
Programming status
Run
Get data block checksum
Load file
Save file
Address of data
Click and enter new address.
HEX code Display
Click to enter hexadecimal data.
ASCII code Display
Click to enter text.
Exit edit window
Data block -
Move/Copy/Swap
Confirm changes
Cancel changes
Set data block range by load file size
Data block - Fill
Set data block range by selected IC size
Set data block range by maximum size of buffer
Stand-Alone Operation Mode
Main frame
LCD Display Keypad
IC number IC Checksum
29F010 E700
C+P+V 5.00V
Programming Voltage
Procedure
Function Descriptions
FUNC.
TYPE
BLANK
VER.
/SUM
COPY
Select IC Vendor
Switch IC Number
Blank Check to SLAVE
Read Checksum of MASTER and verify with SLAVE
Copy MASTER to SALVE
Blank Check
IC number IC Checksum
29F010 ****
Checking >
Status
O.K.
29F010 ****
Checking PASS
ERROR
29F010 ****
Checking FAIL
Read & Verify Checksum
Read Checksum of MASTER
IC number Previous IC
Checksum
O.K.
29F010 5612
Verify PASS
29F010 26AF
Verify >
Read Checksum of MASTER
Status
ERROR
29F010 12EF
Verify FAIL
COPY
IC number Previous IC
Checksum
29F010 26AF
Verify >
Erase, Check, Program,
Verify & Protect according to Prog. Procedure
O.K.
29F010 1A36
COPY PASS
ERROR
29F010 1312
Verify FAIL
Wrong procedure
Select IC Vendor
LCD Display
Select IC Vendor
Select Vendor
AMD
IC brand
Keypad Function Descriptions
FUNC.
TYPE
Select Prog. Procedure
Switch IC Number
BLANK
VER.
/SUM
COPY
No function
Confirm IC brand
No function
Programming Procedure
LCD Display Keypad
Select Prog. Procedure
Select Procedure
C+P+V
Prog. Procedure
Function Descriptions
FUNC.
TYPE
BLANK
VER.
/SUM
COPY
Flash - to select IC Vendor
27CXXX- to select Algorithm
Switch Prog. Procedure
No function
Confirm Prog. Procedure
No function
Programming Algorithm
LCD Display Keypad Function Descriptions
Select Prog. Algorithm
FUNC.
Select Prog. Algorithm
Select Algorithm
Q-100uS
Prog. Algorithm
** Only 27Cxxx **
Programming Voltage
LCD Display Keypad
TYPE
BLANK
VER.
/SUM
COPY
Switch Prog. Algorithm
No function
Confirm Prog. Algorithm
No function
Function Descriptions
Select Prog. Voltage
Select Voltage
12.70V
Prog. Voltage
** Only 27Cxxx **
FUNC.
Select IC Vendor
TYPE Switch Prog. Voltage
BLANK
VER.
/SUM
COPY
No function
Confirm Prog. Voltage
No function
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement