Control Your Video
DVI Dual Link Extender over 2 Strand
Multi-Mode Fiber Optic
Model #: FO-DVI-DL-1000M
© 2011 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with
respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any
time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in
Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products
including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
Reproduction of this manual, or parts thereof, in any form, without the express written permission of Avenview Inc. is strictly prohibited.
www.avenview.com
1
Table of Contents
Section 1: Getting Started ...................................................................................................................... 3
1.1
Important Safeguards ............................................................................................................ 3
1.2
Safety Instructions ................................................................................................................. 3
1.3
Regulatory Notices Federal Communications Commission (FCC) ......................................... 4
1.4
Introduction ........................................................................................................................... 4
1.5
Package Contents................................................................................................................... 5
1.6
Before Installation.................................................................................................................. 5
1.7
Panel Description ................................................................................................................... 6
1.8
Installation ............................................................................................................................. 7
Section 2: Specifications......................................................................................................................... 8
2.1 Signal Pin Assignment (Single Link) .............................................................................................. 9
2.2 Signal Pin Assignment (Dual Link) .............................................................................................. 10
www.avenview.com
2
Section 1: Getting Started
1.1
Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover


Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
 Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized
product modification, or failure to follow instructions supplied with the product.
 Repair or attempted repair by anyone not authorized by us.
 Any damage of the product due to shipment.
 Removal or installation of the product.
 Causes external to the product, such as electric power fluctuation or failure.
 Use of supplies or parts not meeting our specifications.
 Normal wear and tear.
 Any other causes which does not relate to a product defect.

Removal, installation, and set-up service charges.
1.2
Safety Instructions
The Avenview FO-DVI-DL-1000M, DVI Dual Link Extender over Fiber Optic, has been tested for conformance
to safety regulations and requirements, and has been certified for international use. However, like all
electronic equipment’s, the FO-DVI-DL-1000M should be used with care. Read the following safety
instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.




Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to
dangerous voltage or other hazards


Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid
falls or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.


www.avenview.com
3
1.3
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this
equipment.
1.4
Introduction
Avenview FO-DVI-DL-10000M, Dual Link DVI Extender over two fiber solution lets you extend dual link digital
signal up to 300m (1000 feet).
-
High Speed and long distance transmission
Uses 2 strand multi-mode SC type Multi-Mode fiber optic cable
TMDS video signal and EDID data is transmitted by optical fiber
Supports up to Dual Link WQXGA (2560 x 1600) resolution and WUXGA (1920x1200) Single link
Extend 2560x1600 Dual Link or 1920x1200 Single Link video signal up to 300m ( 1000 feet)
DVI Specification 1.0 compliant
Supports HDCP compliant devices with HDCP rev 1.1 specifications
www.avenview.com
4
1.5
Package Contents
Before you start the installation of the converter, please check the package contents.
-
FO-DVI-DL-10000M Transmitter
FO-DVI-DL-10000M Receiver
Power Adapter (+5VDC 2A)
x1
x1
x1
-
User’s Manual
x1
Fiber Optic Cable is not included in the package
1.6




Before Installation
Put the product in an even and stable location. If the product falls down or drops, it may cause an
injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high
humidity.
Use the DC power adapter with correct specifications. If inappropriate power supply is used then it
may cause a fire.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
www.avenview.com
5
1.7
Panel Description
www.avenview.com
6
1.8
Installation
Avenview FO-DVI-DL-10000M is composed of a transmitter and a receiver. The Transmitter should be
connected to the computer’s DVI Port and the Receiver should be connected the DVI Port of the digital display
device.
Avenview FO-DVI-DL-10000M Transmitter is designed to be used with the LC type standard optical cable.
Transmitter and Receiver have each of 7 Optical port which are marked on the optical port of the fiber cable
connection.
To setup Avenview FO-DVI-DL-1000M follow these steps for connecting to a device:
1. Connect FO-DVI-DL-1000M Transmitter unit to DVI source
2. Connect FO-DVI-DL-1000M Receiver unit to DVI port of display.
3. Connect 2 Strand Fiber Optic LC Type cable to both Transmitter and Receiver.
4. Plug the power to Receiver Unit.
5. Power on DVI Source and DVI Display.
Use the DC adapter (included in the package) for the Receiver. The Transmitter which is connected
to a computer uses power from the computer.
If Transmitter power LED doesn’t light up after PC is turned on, then use optional external power
adapter for Transmitter.
www.avenview.com
7
Section 2: Specifications
Item
Units
Unit Description
Input Signal
Output Signal
Video Bandwidth
Supported Resolution &
Distance
Optical Converter
DVI Connector
Optical Connector
Fiber Type
Dimensions (L x W x H)
Description
FO-DVI-DL-1000M (Transmitter)
FO-DVI-DL-1000M (Receiver
DVI Dual Link Transmitter
DVI Dual Link Receiver
TMDS Signal (DVI 1.0 Standard)
TMDS Signal (DVI 1.0 Standard)
1.65Gbps / Channel
Single Link: WUXGA 1920 x 1200 @ 300 meters ( 1000 feet)
Dual Link: WQXGA 2560 x 1600 @ 300 meters (1000 feet)
850nm, 7 Ch Transmit OSA
850nm, 7 Ch Receive OSA
911nm, 1 Ch VCSEL
980nm, 1Ch VCSEL
980nm, 1 Ch PIN P/D Dioad
911nm, 1 Ch PIN P/D Diode
24 pin DVI-D Plug
2 SC Connector
50/125 µm Multi-mode glass fiber
2.97” x 1.97” x 0.6”
Power Supply
Power Consumption
5V 2A DC
1.5W (max)
Environmental
Operating Temperature
Storage Temperature
Relative Humidity
32˚ ~ 104˚F (0˚ to 40˚C)
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
20~90% RH (no condensation)
www.avenview.com
8
2.1 Signal Pin Assignment (Single Link)
TRANSMITTER
Pin
Signal Assignment
Pin
Signal Assignment
Pin
Signal Assignment
1
T.M.D.S. Data2-
9
T.M.D.S. Data1-
17
T.M.D.S. Data0-
2
T.M.D.S. Data2+
10
T.M.D.S. Data1+
18
T.M.D.S. Data0+
3
T.M.D.S. Data2 Shield
11
T.M.D.S. Data1 Shield
19
T.M.D.S. Data0 Shield
4
No Connect
12
No Connect
20
No Connect
5
No Connect
13
No Connect
21
No Connect
6
DDC Clock (SCL)
14
+5V Power
22
T.M.D.S. Clock Shield
7
DDC Data (SDA)
15
Ground (for +5V)
23
T.M.D.S. Clock+
8
No Connect
16
Hot Plug Detect
24
T.M.D.S. Clock-
Pin
Signal Assignment
Pin
Signal Assignment
Pin
Signal Assignment
1
T.M.D.S. Data2-
9
T.M.D.S. Data1-
17
T.M.D.S. Data0-
2
T.M.D.S. Data2+
10
T.M.D.S. Data1+
18
T.M.D.S. Data0+
3
T.M.D.S. Data2 Shield
11
T.M.D.S. Data1 Shield
19
T.M.D.S. Data0 Shield
4
No Connect
12
No Connect
20
No Connect
5
No Connect
13
No Connect
21
No Connect
6
DDC Clock (SCL)
14
Out +5V Power
22
T.M.D.S. Clock Shield
7
DDC Data (SDA)
15
Ground (for Out +5V)
23
T.M.D.S. Clock+
8
No Connect
16
Hot Plug Detect
24
T.M.D.S. Clock-
RECEIVER
www.avenview.com
9
2.2 Signal Pin Assignment (Dual Link)
TRANSMITTER
Pin
Signal Assignment
Pin
Signal Assignment
Pin
Signal Assignment
1
T.M.D.S. Data2-
9
T.M.D.S. Data1-
17
T.M.D.S. Data0-
2
T.M.D.S. Data2+
10
T.M.D.S. Data1+
18
T.M.D.S. Data0+
3
T.M.D.S. Data2/4 Shield
11
T.M.D.S. Data1/3 Shield
19
T.M.D.S. Data0/5 Shield
4
T.M.D.S. Data4-
12
T.M.D.S Data 3-
20
T.M.D.S. Data5-
5
T.M.D.S. Data4+
13
T.M.D.S. Data3+
21
T.M.D.S. Data5+
6
DDC Clock (SCL)
14
+5V Power
22
T.M.D.S. Clock Shield
7
DDC Data (SDA)
15
Ground (for +5V)
23
T.M.D.S. Clock+
8
No Connect
16
Hot Plug Detect
24
T.M.D.S. Clock-
Pin
Signal Assignment
Pin
Signal Assignment
Pin
Signal Assignment
1
T.M.D.S. Data2-
9
T.M.D.S. Data1-
17
T.M.D.S. Data0-
2
T.M.D.S. Data2+
10
T.M.D.S. Data1+
18
T.M.D.S. Data0+
3
T.M.D.S. Data2/4 Shield
11
T.M.D.S. Data1/3 Shield
19
T.M.D.S. Data0/5 Shield
4
T.M.D.S. Data4-
12
T.M.D.S Data 3-
20
T.M.D.S. Data5-
5
T.M.D.S. Data4+
13
T.M.D.S. Data3+
21
T.M.D.S. Data5+
6
DDC Clock (SCL)
14
Out +5V Power
22
T.M.D.S. Clock Shield
7
DDC Data (SDA)
15
Ground (for Out +5V)
23
T.M.D.S. Clock+
8
No Connect
16
No Connect
24
T.M.D.S. Clock-
RECEIVER
www.avenview.com
10
Control Your Video
TECHNICAL SUPPORT
USA Head Office
Office Avenview Corp.
275 Woodward Avenue
Kenmore, NY14217
Phone: +1.716.218.4100
Fax: +1.866.387-8764
Email: info@avenview.com
Canada Sales
Avenview
151 Esna Park Drive, Units 11 & 12
Markham, Ontario, L3R3B1
Phone: 1.905.907.0525
Fax: 1.866.387.8764
Email: info@avenview.com
Avenview Europe
Avenview Europe
Demkaweg 11
3555 HW Utrecht
Netherlands
Phone: +31(0)85 2100 613
Email: info@avenview.eu
Avenview Hong Kong
Unit 8, 6/f., Kwai Cheong Centre,
50 Kwai Cheong Road,
Kwai Chung, N.T.
Hong kong
Phone: 852.3575.9585
Email: wenxi@avenview.com
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of
Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this
documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages
in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design.
With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but
not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement.