PENTAIR ELECTRONICS PROTECTION
SCHROFF®
Usermanual Rev.1.2(17/04/2015)
CompactPCI Serial power supply
CompactPCI Serial power supply (for illustration only)
CompactPCI Serial is a new standard that supports the fast serial protocols PCI Express, Serial ATA, USB
and Ethernet. The payload power is +12 V. For wake-up events an additional +5 V Stdby voltage is
defined. The Schroff pluggable CompactPCI Serial power supply is developed in accordance to the power
definition within the CompactPCI Serial specification PICMG CPCI-S.0.
The power supply is a 3 U, 8 HP unit and fits into a 3 U subrack slot by using the off-set card guides. The
mains voltage is fed through the connector on the back. Pentair offers the mating power backplanes as
well as CompactPCI Serial backplanes with the mating connector installed.
Main features
Total power
300 W
•
•
•
•
•
•
•
Input voltage
90-264 VAC
Active power factor correction
Wide range input
Active current share – single wire
Remote sensing
N+1 redundancy
PS present
Power fail
Output voltage 1
+12 V
•
•
•
•
•
•
•
Output voltage 2
+5 V Standby
PS_ON
Enable
Temperature monitoring
I2C interface
Hot pluggable
UL, cUL and DEMKO
CE compliant
Amtsgericht Mannheim, HRB 503549
Geschäftsführer: Daniel Stirpe, Henry Grimm
Pentair Technical Solutions GmbH, Langenalber Str. 96-100, D – 75334 Straubenhardt
PENTAIR ELECTRONICS PROTECTION
SCHROFF®
ENVIRONMENTAL SPECIFICATIONS
•
•
•
•
•
Humidity: Up to 95% non-condensing
Storage temperature: -40° to +85°C
Temperature coefficient: ±0.01% / °C
Ambient operating temperature: -40 to +70°C continuous duty, full rating.
Cooling: forced air cooling required
SAFETY APPROVALS
•
•
•
UL:
CUL:
DEMKO:
60950-1:2005 (2nd Edition); Am 1:2009
60950-1:2005 (2nd Edition); Am 1:2009
EN 60950-1:2006, EN 60950-1:2006/A11:2009
EN 60950-1:2006/A1:2010
EN 60950-1:2006/A12:2011
ELECTRICAL SPECIFICATIONS
Inputspecifications
Input range
Frequency
EMI filter
Inrush current
Input current
Isolation
Efficiency
Active PFC
Switching frequency
Leakage
Mainoutputspecifications
90-264 VAC
50-60 Hz
EN55022 Class B, FCC Part 15
<32 A @ 230 VAC
1.3 A @ 264 VAC (1,45 A@230)
4242 VDC (input to output)
>90% @ 230 VAC
0.99
134 KHz
<300 uA
DC output
Line Regulation
Load Regulation
Ripple and Noise
Transient Response
Maximum continuous
output power 300 W with
minimum 10 CFM fan
cooling required.
±2 %
±2 %
1 % Pk to Pk
2 % maximum deviation;
returns to initial condition
in 1 msec max.
Outputspecifications
•
•
•
Long term stability
Hold-up time
OVP
•
Short-circuit protection
•
Overload protection
•
ORing FET
0.01 % after 20 minute warm-up
20 msec minimum
Set at 115 % to 135 %. Latching method. AC must be recycled to
restart the unit
The units will withstand a continuous short without damage. It will
automatically return to regulation upon removal of the short
The overload protection feature will reduce the output voltage to a
safe dissipation level when the output power rating exceeds 110 % of
maximum rated power. The unit will automatically return to
regulation upon removal of the overload
ORing FET provided for redundant operation
Amtsgericht Mannheim, HRB 503549
Geschäftsführer: Daniel Stirpe, Henry Grimm
Pentair Technical Solutions GmbH, Langenalber Str. 96-100, D – 75334 Straubenhardt
PENTAIR ELECTRONICS PROTECTION
SCHROFF®
•
•
Active current share
(S2)
Passive current share
Remote sensing
(R2/E3)
PS_ON (F3)
•
Enable (R6)
•
FAL/PWR_FAIL (U2)
•
DEG (U5)
•
•
PS Present (H3)
Thermal Protection
•
I²C/PMBUS
•
LED Indicators
•
•
12V output will current share within 5% when interconnected by a
single wire
5 VSBY droop type
on 12V output only
Digital Input: A logic low enables the Main output of the supply. A low
shall not source more than 1 mA of current
Digital Input. When driven high, main output is disabled. When Low,
power supply main output state is as controlled by PS_ON
Digital output, Open Collector, driven high when outputs are in
regulation. It will go low a minimum of 1 mS prior to output going out
of regulation
Open Collector, temperature warning signal default setting at 85°C
will change signal state from Hi to Low or Low to Hi (signal and
temperature preferences programmable at factory)
Digital Output. Pulled low via 100 Ohm resistor
The power supply has a built in thermal sensor to protect against
abnormal temperature conditions
Monitors temperature, output voltage, and output current, connects
to a serial NVRAM which is programmed with serial number. PMBUS
Standard to allow monitoring of overall operation of power supply
The power supply will have two LED’s providing the power supply
status:
Status
Indication
All outputs are operating within spec
Steady Green
Standby (PSON disabled)
Blinking Green
Voltage or Temperature warning
Blinking Yellow
Voltage or Temperature fault
Steady Yellow
PSKILL and/or power supply off
NO LED’s
OVERALL MECHANICAL DIMENSIONS
Not including face plate and connector
6.40”L x 3.94”H x 1.47”W
162.5mm x 100mm x 37.34mm
Including face plate and connector:
6.67”L x 5.06”H x 1.59”W
169.4mm x 128.5mm x 40.3mm
Amtsgericht Mannheim, HRB 503549
Geschäftsführer: Daniel Stirpe, Henry Grimm
Pentair Technical Solutions GmbH, Langenalber Str. 96-100, D – 75334 Straubenhardt
PENTAIR ELECTRONICS PROTECTION
SCHROFF®
NOTES
•
•
•
Specifications subject to change without notice.
All dimensions in inches/mm
Weight: Approx. 1.6lbs (0.68Kg)
VOLTAGE/CURRENT RATING CHART
Item number
Assignment
V1
V2
11098-538
Voltages
12 V
5 VSB
Minimum
0A
0A
Maximum
25.0 A
2.5 A
CONNECTOR
Input/Output……………….FCI Connector 51939-667
H3
U4
U5
U6
NU
FAL /
PWR_FAIL
PS
PRESENT
COM
DEG
5V STBY
T1
T2
G3
T4
T5
T6
NU
NU
COM
A0
5V STBY
5V STBY
S1
S2
F3
S4
S5
S6
NU
12V CS
PSON
A1
SCL
COM
R1
R2
E3
R4
R5
R6
NU
-VS
+VS
A2
SDA
ENABLE
P6
P7
P8
P9
+12V OUT
U2
+12V OUT
U1
COM
P5
NU
P4
NU
P3
GND
P2
NEUTRAL
LINE
P1
COM
Pinout
H3, G3, F3 and E3 are shorter pins
Amtsgericht Mannheim, HRB 503549
Geschäftsführer: Daniel Stirpe, Henry Grimm
Pentair Technical Solutions GmbH, Langenalber Str. 96-100, D – 75334 Straubenhardt
PENTAIR ELECTRONICS PROTECTION
SCHROFF®
Warranty conditions
Duration
This product has a warranty of 2 years. The warranty begins on the day of delivery
Coverofdefects
Within the warranty period Schroff will repair free of charge any faulty functioning of the product resulting from faulty design or
defective material. All other claims under the warranty are excluded, in particular consequential damage.
Warrantyexclusion
The warranty does not cover damage or functional defects caused by non-adherence to the Company´s operating instructions or
such caused by dropping, knocking, contamination or other untoward handling. The warranty is invalidated if the product is
opened by unauthorized personnel, tampered with or the serial number on the product has been changed or rendered illegible.
Claimsunderwarranty
This product has been carefully checked. If you have a valid claim, please return the product to SCHROFF. In order to make a
claim under the warranty, ensure that the following is carried out:
•
Include a detailed description of the fault.
•
The product should be returned in the original
carton or similar packaging, insured and postpaid.
Amtsgericht Mannheim, HRB 503549
Geschäftsführer: Daniel Stirpe, Henry Grimm
Pentair Technical Solutions GmbH, Langenalber Str. 96-100, D – 75334 Straubenhardt