AS112 User manual - Gold Apollo Co., Ltd

User Manual For LED Alpha Sign
GOLD APOLLO CO.,LTD.
Gold Apollo LED Sign Relay Output Pin Instruction
* 1.
RS-232-DB9 Male as Relay Output Pins
Pin No.
Signal
1
2
3
4
5
6
7
8
9
Normal Open
Normal Open
The Total Max. Current < = 2A
1
5
Normal Open
Common
Common
Common
Normal Close
Normal Close
Normal Close
01
6
9
LED sign’s Control Commands V2.00 (use for LED sign firmware V6.0 up)
Item
Features
Command
Timer display On/Off GALEDTM=
GALEDDT=
Timer Date On/Off
Timer Date Setting
GALEDDATE=
4
Timer Date mode
GALEDDTMD=
X
5
GALEDTIME=
HHmmSS
6
Timer Time Setting
Timer Month
language of Date
GALEDLANG=
XXX
7
Timer Display Mode
GALEDTMD=
8
Timer Hour Type
GALEDSHTM=
Timer display
9
hold time
10 Buzzer On/Off
11 Buzzer On Time
12 Buzzer music type
ON or OFF
ON or OFF
YYMMDD
ON = Timer display enable , OFF = Timer display disable
Date display ON or OFF
YY= year from 0 to 99 , MM= month from 1 to 12, DD= day from 1 to 31
0 = DD-MMM-YY , 1 = MMMM DD,YY , 2 = MM/DD/YY , 3 = DD/MM/YY ,
4= MM-DD-YY, 5 = DD-MM-YY, 6 = MM.DD.YY, 7 = DD.MM.YY, 8 = MM DD YY ,
9 = DD MM YY
HH= hour from 00 to 23 , mm = minute from 00 to 59 , SS = second from 00 to 59
ENG = English , FRA= France
X
This control command will not work on LED Sign Type = A or B mode.
1 = Timer display after every message ,
2=Timer display once after finished all messages
12 or 24
24= 24 hours type(default ) , 12=12 hours type with AM, PM indicator.
GALEDSHTM=
XXX
GALEDBZ=
GALEDBZTM=
GALEDBZTY=
ON or OFF
XXX
X
13 Scroll Speed control GALEDSPEED=
Description
Parameters
1
2
3
X
14 Default message
GALEDMESG=
xxxxx…
15 Message Counter
GALEDMGCT=
XX
from 001 to 999 seconds
ON = Buzzer beep enable , OFF = Buzzer beep disable
from 001 to 999 seconds
Music type from 0 to 9
X = 1 ( slowest ) to 5 ( fastest ) , this scroll feature only active the message
length more then LED sign display’s character length. It will be setting to
default value when the LED Sign Type command is changed.
It keep 50 characters for message to replace default message of "Gold Apollo
LED signs moving display" , If use “GALEDTIME=HHmmSS”as the default
message then the default message will show time information on the LED sign.
01= only use one message slot for any capcode and function bits, 24 = each
capcode and function will locate its message slot, AU= Auto can have 24 memory
but does not care capcodes, this 24 memories will do FIFO action, it mean if It’s
memory full then oldest memory will move out memory.
02
16 Auto Clear delay time GALEDCLRDY=
XXX
Auto Clear Count
17
times
XXX
18
Clear by "Reset"
command
19 Time Stamp Mode
GALEDCLRCT=
GALEDRESCM= ON or OFF
GALEDTMSM=
20 Non Scroll Hold time GALEDMGTM=
X
XXX
21 Delete All Messages GALEDDELALL
* 2.
22 LED Sign Type
GALEDTYPE=
X
Message Display
23 Sequence
GALEDSEQU=
X
GALEDAPPM=
X
* 2.
24
Appear Message
Mode
000= auto clear disable, delay time = 001 to 999 seconds, message will auto
clear itself after delay time is time out.
000= auto clear disable, display how many times = 001 to 999 times, message will
auto clear itself after display times is time out.
ON = if the message have header or trailer with "reset" and space words then
the same message will be cleared. The header format is "reset"+" "(space), the
trailer format is " "(space) +"reset" . And the "reset" will do not care the lower or
upper caps.
0 = Off , 1 = time stamp in the head of message , 2 = time stamp in the end of
message , time stamp format is HH:MM ( 24 hours time format)
from 001 to 999 seconds, this feature only active when the message length less
then LED sign’s character length , the default time is 3 seconds.
This command will clear all messages then it will show the default message on
the LED sign.
1= 1 line
2= 2 lines
A= 2 lines with timer and timer is on second line
B= 2 lines with timer and timer is on first line
a= 2 lines with default message and default message is on second line
b= 2 lines with default message and default message is on first line
0 = FIFO (First In First Out)
1 = LIFO (Last In First Out)
This feature only work for LED Sign Type = 1 or 2.
0 = Fly to Left (default)
1 = Enter to Right
2 = Extended to Buttom
3 = FLY from Top
4 = FLY from Buttom
5 = Raining
6 = Snow Flakes
7 = Appear right away
8 = Animation 1
* 2. Only for AS112, AS122, AS212 or AS222.
03
GALEDDISM=
X
This feature only work for LED Sign Type = 1 or 2.
0 = Continue (default)
1 = Run to Left
2 = Curtain Right
3 = Curtain Down
4 = Fly Away
5 = Sink
6 = Flash & Invert
7 = Vapor
8 = Dissolve
9 = Flash
A = Disappear right away
B = Animation 1
GALEDDISM=
X
Color definition : 1= Red color, 2= Green color. 3= Orange color
GALEDDISM=
X
Color definition : 0: Disable, 1= Red color ,2= Green color. 3= Orange color
If priority color is disable then it will display default color.
GALEDDISM=
XXX
Color definition : 0: Disable, 1= Red color ,2= Green color. 3= Orange color
XXX is capcode 1, 2, 3, 4 for flex system
XXX is function code A, B, C, D of capcode 1 for POCSAG system
GALEDDISM=
XXX
Color definition : 0: Disable, 1= Red color ,2= Green color. 3= Orange color
XXX is capcode 5, 6, 7, 8 for flex system
XXX is function code A, B, C, D of capcode 2 for POCSAG system
GALEDDISM=
XXX
Color definition : 0: Disable, 1= Red color ,2= Green color. 3= Orange color
XXX is capcode 9, 10, 11, 12 for flex system
XXX is function code A, B, C, D of capcode 3 for POCSAG system
* 2.
25 Disappear Message
Mode
* 3.
26 Default Color
* 3.
27 Priority Message
Color
* 3.
28 Capcode Color
Group A
* 3.
29 Capcode Color
Group B
* 3.
30 Capcode Color
Group C
* 2. Only for AS112, AS122, AS212 or AS222.
* 3. Only for AS210(R), AS220(R), AS212(R), orAS222(R).
04
* 3.
31 Capcode Color
Group D
GALEDDISM=
X
Color definition : 0: Disable, 1= Red color ,2= Green color. 3= Orange color
XXX is capcode 13, 14, 15, 16 for flex system
XXX is function code A, B, C, D of capcode 4 for POCSAG system
GALEDDISM=
XXX
Color definition : 0: Disable, 1= Red color ,2= Green color. 3= Orange color
XXX is unused for flex system
XXX is function code A, B, C, D of capcode 5 for POCSAG system
GALEDDISM=
XXX
Color definition : 0: Disable, 1= Red color ,2= Green color. 3= Orange color
XXX is unused for flex system
XXX is function code A, B, C, D of capcode 6 for POCSAG system
GALEDDISM=
ON or OFF
* 3.
32 Capcode Color
Group A
33
* 3.
Capcode Color
Group B
34
* 3.
Message Color
Command
If Message Color Command is ON then message color can be changed in the
message specific date. <*CG1*>= Red color, <*CG2*>= Green color, <*CG3*>=
Orange color. The message will change color after Message Command Color.
And this color changed only work on this message.
LED Sign Priority Message features V1.12
0 : Off
* 1.
35
Prior ity Message
GALEDPRIM=
X
1 : Priority Message On without Relay and Priority Message Capcode without
Relay
2 : Priority Message On with Relay On and Priority Message Capcode without
Relay
3 : Priority Message On without Relay and Priority Message Capcode with Relay
On
4 : Both Priority Message and Priority Message Capcode with Relay On
* 3. Only for AS210(R), AS220(R), AS212(R), orAS222(R).
* 1. Only for AS110R ‚ AS112R ‚ AS120R ‚ AS122R, AS210R, AS212, AS220R, AS222R.
05
36
* 1.
Prior ity Message
Relay On time
GALEDRLYTM=
XXX
GALEDPRICAP=
XXXXXX
* 1.
37 Prior ity Message
Capcode select ion
0 – 999 seconds
000000 –FFFFFF , this code is only valid 0 - 9 and A-F, that will be a hex code for
thecapcode select for priority message. And the bit = 1 then the priority message
is enabled.
Flex system will only work four codes for the 16 capcodes, and POCSAG system
will work for six codes for 24 capcodes.
Flex system : Highest bit will be a capcode 1, next highest bit is capcode 2 ... so
the capcode 16 is fourth code lowest bit.
POCSAG system : Highest bit will be a capcode 1 function code = 00, next
highest bit is capcode 1 function code = 01, next highest bit is capcode 1 function
code = 10, next highest bit is capcode 1 function code = 11 ... so capcode 6
function code = 11 is the lowest bit.
* 1.
38 Mail Drop Capcode
select ion
GALEDMDCAP=
XXXXXX
000000 – FFFFFF , this code is only valid 0 - 9 and A-F, that will be a hex code for
the capcode select for Mail Drop message. And the bit = 1 then the Mail Drop
message is enabled.
Flex system will only work four codes for the 16 capcodes, and POCSAG system
will work for six codes for 24 capcodes.
Flex system : Highest bit will be a capcode 1, next highest bit is capcode 2 ... so
the capcode 16 is fourth code lowest bit.
POCSAG system : Highest bit will be a capcode 1 function code = 00, next highest
bit is capcode 1 function code = 01, next highest bit is capcode 1 function code
= 10, next highest bit is capcode 1 function code = 11 ... so capcode 6 function
code = 11 is the lowest bit.
If Mail Drop capcode is enabled one then the message counter will be decreased
one.
* 1. Only for AS110R ‚ AS112R ‚ AS120R ‚ AS122R, AS210R, AS212, AS220R, AS222R.
06
* 1.
39
Mail Drop Time Out
Off
GALEDMDTOOF=
ON or OFF
* 1.
40
41
Prior ity Message
Counter
X
* 1.
Prior ity Message
Clear
42
GALEDPRICT=
GALEDPRICLR=
ON = Mail Drop Time Out off
OFF = Mail Drop Time Out is same as normal message
X=1 to 5 , it can be selected priority message can display and store from 1 to 5
messages
ON or OFF
ON = Priority message clear command is enabled then it will accept “CLEAR” air
command to clear all priority messages. And the “CLEAR” will do not care the
lower or upper caps.
XX
X=01 to 24, it allow user to select message counter at automatic message mode.
* 1.
Autom atic Message
Counter
GALEDAUCT=
* 1.
43
Prior ity Message auto GALEDPCLRDY=
clear delay time
XXX
000= Priority Message auto clear disable, delay time = 001 to 999 seconds,
Priority Message will auto clear itself after delay time is time out.
* 1.
44
45
Message Number of
Sequence
GALEDMGNO=
ON or OFF
GALEDTMHR=
12 or 24
Message Number disaplay = On or Off
* 1.
Timer Hour Type
24= 24 hours type ( default ) , 12 = 12 hours type with AM , PM indicator.
* 1. Only for AS110R ‚ AS112R ‚ AS120R ‚ AS122R, AS210R, AS212, AS220R, AS222R.
07
Control command instruction and Examples:
1: Timer display On/Off
GALEDTM=ON
Description: Timer display enables.
2: Timer Date On/Off
GALEDDT=OFF
Description: Date disable at timer display.
3: Timer Date Setting
GALEDDATE=061025
Description: The timer’s date will set to 2006, Oct, 25
4: Timer Date mode
GALEDDTMD=5
Description: If the timer set to 2006, Oct, 25 then it will show 25-10-06
on the display.
5: Timer Time Setting
Timer Time Setting=061025
Description: The timer’s time will set to 06:10AM 25 seconds
6: Timer Month language of Date
GALEDLANG=ENG
Description: If the timer set to 2006, Oct, 25 and Date mode set to
DD-MMM-YY then it will show 25-OCT-06 on the display.
08
7: Timer Display Mode
GALEDTMD=1
Description: There are three messages then it will show as following,
Message 1 → timer display → Message 2 → timer display
→ Message 3 → timer display → Message 1... (repeat)
GALEDTMD=2
Description: There are three messages then it will show as following,
Message 1 → Message 2 → Message 3 → timer display
→ Message 1... (Repeat)
8: Timer Hour Type
GALEDTMHR=12
Description: The timer’s hour type can be selected 12 hours.
The default type is 24 hours.
9: Timer display hold time
GALEDSHTM=005
Description: The timer’s time will show and hold 5 seconds.
10: Buzzer On/Off
GALEDBZ=ON
Description: The Buzzer’s Beep is enabled.
11: Buzzer On Time
GALEDBZTM=008
Description: The Beep time is selected to 8 seconds.
09
12: Buzzer music type
GALEDBZTY=0
Description: The Beep type is selected to 0.
13: Scroll Speed control
GALEDSPEED=5
Description: The Scroll Speed is selected to fastest. Please note the
scroll feature only work when your message more LED sign’s character
length. If you LED sign’s length is 20 characters then your message
must more 21 characters then scroll feature will work otherwise the
message will be hold and the hold time define by command item 19
(Non Scroll Hold time).
14: Default message
GALEDMESG=Gold Apollo default message
Description: The default message will be replaced to “Gold Apollo
default message”. This message will show when you delete all messages.
GALEDMESG=GALEDTIME=HHmmSS
Description: The default message will be replaced to time information
“16:24:35”. This time information will show when you delete all messages.
15: Message Counter
GALEDMGCT=XX
Description: If the LED sign is deleted all messages and do a following
paging examples : ( it is used Message Display Sequence = LIFO )
10
Step 1. Paging capcode 1 tone A : message 1
GALEDMGCT=01 (this is the command’s selection)
GALEDMGCT=24 (the last message will show first)
GALEDMGCT=AU (the last message will show first)
message 1 → ... repeat ( this is the message display on the LED sign )
Step 2.Paging capcode 1 tone B : message 2
GALEDMGCT=01
message 2 → ... repeat
GALEDMGCT=24
GALEDMGCT=AU
message 2 → message 1 → ... Repeat
Step 3.Paging capcode 1 tone C : message 3
GALEDMGCT=01
message 3 → ... repeat
GALEDMGCT=24
GALEDMGCT=AU
message 3 → message 2 → message 1 → ... repeat
Step 4.Paging capcode 1 tone D : message 4
GALEDMGCT=01
message 4 → ... repeat
GALEDMGCT=24
GALEDMGCT=AU
message 4 → message 3 → message 2 → message 1 → ... Repeat
11
Step 5.Paging capcode 1 tone A : message 5
GALEDMGCT=01
message 5 → ... repeat
GALEDMGCT=24
message 5 → message 4 → message 3 → message 2 → ... repeat
GALEDMGCT=AU
message 5 → message 4 → message 3 → message 2 →
message 1 → ... repeat
Step 6.Paging capcode 1 tone B : message 6
GALEDMGCT=01
message 6 → ... repeat
GALEDMGCT=24
message 6 → message 5 → message 4 → message 3 → ... repeat
GALEDMGCT=AU
message 6 → message 5 → message 4 → message 3 →
message 2 → message 1 → ... Repeat
16: Auto Clear delay time
GALEDCLRDY=030
Description: The receiving message will show 30 seconds then it will
be clear itself.
12
17: Clear Count times
GALEDRESCM=030
Description: The receiving message will show 30 times then it will
be clear itself
18: Clear by "Reset" command
GALEDRESCM=ON
Description: The Clear by "Reset" command is enabled. So you can
do clear message as following,
Example 1: Message content is “this is a test”
reset this is a test
This head reset command will clear the message.
Example 2: Message content is “this is a test”
this is a test RESET
This reset command at trailer will clear the message.
19: Time Stamp Mode
GALEDTMSM=1
Description: The receiving message will be added time stamp in the
head of message.
Example: Message content is “this is a test” , Time is 17:58.
LED Sing will show it as 17:58 this is a test.
20: Non Scroll Hold time
GALEDMGTM=005
Description: The non scroll message will show and hold 5 seconds.
Please also refer command item 12 (Scroll Speed control).
13
21: Delete All Messages
GALEDDELALL
Description: It will delete all messages and it will show the default
message on LED sign. Please also refer command item 13 (Default
message).
22: LED Sign Type
GALEDTYPE=2
Description: The LED Sign type will change to 2 lines display mode.
23: Message Display Sequence
GALEDSEQU=1
Description: The LED Sign will display message as first in first out mode.
24: Appear Message Mode
GALEDAPPM=8
Description: The LED Sign will display an animation first then display
the message.
25: Disappear Message Mode
GALEDDISM=B
Description: The LED Sign will display an animation follow the message.
14
26: Default color Type
GALEDCOLOR=1
Description: The LED Sign will display message in Red color.
The number 1= Red color, 2= Green color, 3= Orange color.
27: Priority message color Type
GALEDPCOLOR=1
Description: The LED Sign will display priority message in Red color.
The number 1= Red color, 2= Green color, 3= Orange color.
28: Capcode A color Type
GALEDCAPCLA=0123
Description: The LED Sign will display message color by sapcode ID.
The number sequence use for ID 1, 2, 3, 4, The number 0= disable(use
default color) ,1= Red color, 2= Green color, 3= Orange color.So this case
will display ID 1 as default color, ID 2= red color, ID 3= green color, ID 4=
orange color.
29: CapcodeB color Type
GALEDPCOLOR=1123
Description: The LED Sign will display message color by sapcode ID.
The number sequence use for ID 5, 6, 7, 8, The number 0= disable(use
default color) ,1= Red color, 2= Green color, 3= Orange color.So this case
will display ID 5 as red color, ID 6= red color, ID 7= green color, ID 8=
orange color.
15
30: Capcode C color Type
GALEDPCOLOR=1111
Description: The LED Sign will display message color by sapcode ID.
The number sequence use for ID 9, 10, 11, 12, The number 0= disable(use
default color) ,1= Red color, 2= Green color, 3= Orange color.So this case
will display ID 9 as red color, ID 10= red color, ID 11= green color, ID 12=
orange color.
31: Capcode D color Type
GALEDPCOLOR=2222
Description: The LED Sign will display message color by sapcode ID.
The number sequence use for ID 13, 14, 15, 16, The number 0= disable(use
default color) ,1= Red color, 2= Green color, 3= Orange color.So this case
will display ID 13 as green color, ID 14= green color, ID 15= green color, ID 16=
green color.
32: Capcode E color Type
GALEDPCOLOR=3333
Description: The LED Sign will display message color by sapcode ID.
The number sequence use for ID 13, 14, 15, 16, The number 0= disable(use
default color) ,1= Red color, 2= Green color, 3= Orange color.So this case
will display ID 13 as green color, ID 14= green color, ID 15= green color, ID 16=
green color.
16
33: Capcode F color Type
GALEDPCOLOR=0000
Description: The LED Sign will display message color by sapcode ID.
The number sequence use for ID 21, 22, 23, 24, The number 0= disable(use
default color) ,1= Red color, 2= Green color, 3= Orange color.So this case
will display ID 21-24 asdefault color.
34: Message color command
GALEDPMSGCL=NO
Description: The LED Sign Message color command is turned on then the
color can be selected by specific message command.
Example 1 : Default color= Red color, message=”This is a test <*CG2*>
Message color command”
The LED Sing display will show → This is a test Message color command
Example 2 : Default color= Orang color, message=”This is a test <*CG2*>
Message <*CG3*>color<*CG3*> command”
The LED Sing display will show → This is a test Message color command
35: Priority Message
911 as Priority Message prefix code. it will not show 911 on the display. but it also can be used the RESET
control command to cancel this priority message in the AS control commands. The other way is used a new
“CLEAR” priority message air command to clear it or a message time out feature be implemented. The nonpriority message auto clear timer/counters are on hold while priority messages are being displayed.
17
36: Priority Message Relay On time
Both Priority Message and Priority Message Capcode features also can be enabled an external relay ON for
a duty time.
37: Priority Message Capcode selection
Priority Message by Capcode will be accepted for the AS110R ‚ AS112R ‚ AS120R ‚ AS122R.
38: Mail Drop Capcode selection
Mail Drop capcode selection. it can be selected capcode as a mail drop and it only has one message for the
capcode. and this feature only can be used for the Message Counter = Auto.
39: Mail Drop Time Out Off
Mail Drop message can be selected a Time Out feature off. that will can used same time out as normal
capcode or it will turn off the time out feature !
40: Priority Message Counter
Priority Message can be extended to 5 messages.
41: Priority Message Clear
Priority Message also support an easy “CLEAR” air command for user to use.
42: Automatic Message Counter
Add a selection of 1 to 24 number for automatic message mode.
18
43: Priority Message auto clear delay time
Priority Message auto clear feature will have an independent time out.
44: Message Number of Sequence
Message Number can be selected on or off.
45: Timer Hour Type
Timer hour type can be selected 12 or 24 hours .
19
MEMO
GOLD APOLLO CO.,LTD.
User Manual
Manual For
For LED
LED Alpha
Alpha Sign
Sign
User