Safe Operations Manual

INSTRUCTIONS
FOR SAFE
OPERATIONS
TOUGHPIX II
EXPLOSION PROOF
DIGITAL CAMERA
RUGGED AUTHORITY
www.cord-ex.com
ToughPIX II – Explosion Proof Digital Camera
CONTENTS
READ THIS FIRST
Read This First
Liability
Trademark Information
Product Information
3
3
3
3
Instructions for Safe Use
4
Labelling
5
Operational Cautions
6
Certification
EC Declaration of Conformity
ATEX / IECEx Certificate
7
8
9
The ToughPIX II 24xx range of flameproof
digital cameras are suitable for use in
hazardous areas (Ex zones: potentially
explosive environments).
Read and understand all Warnings and
Cautions before using this product.
Liability
The technical specification of the camera
complies with relevant European Ex standards
(EN 60079-0 and EN60079-1).
The user is solely responsible for ensuring the
equipment is suitable for the intended purpose
and environments.
CorDEX Instruments will not be liable for any
injury or damage resulting from unauthorized
adjustments to, or dismantling of, the camera
or for use with inappropriate applications or
environments.
RUGGED AUTHORITY
Trademark Information
Microsoft® and Windows® are U.S. registered
trademarks of Microsoft Corporation. Pentium®
is a registered trademark of Intel Corporation.
Macintosh is a trademark of Apple Computer,
Inc. SD™ is a trademark.
Other names and products may be trademarks
or registered trademarks of their respective
owners.
Product Information
Product design and specifications are subject
to change without notice. This includes
primary specifications, software, software
drivers, and user’s manual. The User Manual
is a general reference guide for the product.
The manufacturer assumes no liability for any
errors or discrepancies in the user manual.
3
ToughPIX II – Explosion Proof Digital Camera
INSTRUCTIONS FOR
SAFE USE
The conditions referenced in this section
relate specifically to hazardous area
applications and must be followed.
In accordance with clause 5.1 of EN 60079-1,
the critical dimensions of the flamepaths are:
Flamepath
Maximum
Gap (mm)
Minimum L
(mm)
Rearcarriage/
front carriage
0.04
6.5
Flash
Window/
frontcarriage
0.1
13.8
LCDWindow/
frontcarriage
0.1
13.8
Lens window/
frontcarriage
0.1
13.8
Operatingrod/
rear and
0.1
10.5
• Contact the manufacturer for information on
the dimensions of the flameproof joint
• The apparatus must only be used in areas
where there is low risk of impac
• Do not charge battery pack in the hazardous
are
• The battery must be removed from the
camera and charged in the CorDEX
Instruments ToughPIX II charging bay part
number CDX-2400-XXX. Using a different
charging device will void the certification.
Focus Ring
RUGGED AUTHORITY
LABELLING
• The ToughPIX II 2410 Series digital camera
incorporates a protected battery system
with a non-replaceable fuse. This fuse is
only to be replaced by CorDEX Instruments
or a CorDEX Instruments Approved Repair
Facility. Failure to do so will void the
certification.
• Ensure that the ToughPIX II 2410 Series
digital camera battery pack is secured
using the plug provided. If the plug is lost,
only replace with a plug of the correct size
and type. If in doubt, contact your nearest
CorDEX Instruments representative.
• The ToughPIX II 2410 Series digital camera
is manufactured from aluminium alloy; and
must contain less than 7% magnesium by
weight and incorporates toughened glass
windows. This should be taken into account
when considering the end use application.
CorDEX Instruments Ltd. 1 Owens Rd, Middlesbrough, TS6 6HE, UK
TP2410 – Explosionproof Digital Camera
II 2 G
Ex d IIB+H2 T6 GbTamb -20°C to +50°C
ATEX –TRAC13ATEX0046X
IECEx :IECEx TRC 13.0016X
Serial Number- XXXX-XX-XXXX
Year of Construction- YYYY
Powered by – Refer to Manual
XXXX
DO NOT OPEN WHEN EXPLOSIVE ATMOSPHERE PRESENT
• TheToughPIX II 2410 Series digital camera
cannot be maintained in the field andmust
be returned to the manufacturer should
repair or maintenance be required.
• USB communications with the ToughPIX II
2410 Series digital camera must only occur
within the non-hazardous area
• When replacing the battery pack, the screw
must be re-tightened to a torque of 1.5-4Nm
and the cover cap replaced.
• Only CorDEX battery pack CDX2400-011 shall
be use
135˚ Swivel Lens
5
ToughPIX II – Explosion Proof Digital Camera
OPERATIONAL
CAUTIONS
CERTIFICATION
The cautions contained in this section do not
relate specifically to safe use in hazardous
area applications but should be followed
to help prevent damage to the device or
personnel.
Model
TP2410
ATEX Certificate No.
TRAC13ATEX0046X
ATEX Coding
XXXX
• Keep out of reach of children
• The TP2410 is a precision instruction. Do not
drop it, strike it or use excessive force when
handling
IIB+H2 T6 Gb Tamb -20°C to +50°C
Ambient Temperature
-20° to +50°C
Power Supply
ToughPIX II 2410 Series Removable Rechargeable Battery Pack,
part number CDX-2410-011
Maintenance
For safety critical maintenance, please refer
to EN60079-17
RUGGED AUTHORITY
These will need
replacing with new
7
ToughPIX II – Explosion Proof Digital Camera
EC DECLARATION
OF CONFORMITY
CorDEX Instruments Ltd
Unit 1, Owens Road
Skippers Lane Industrial
Estate,
MIDDLESBROUGH,
TS6 6HE
Declaration No. SO/11 Rev 3
EC Declaration of Conformity
in accordance with EEC ATEX Directive 94/9/EC
We,
CorDEX Instruments Ltd.
Hereby declare that the products described below
Product:
Model:
Explosion-proof digital camera
TP2410XP
are in conformity with the essential health and safety requirements of Council Directive
94/9/EC relating to equipment intended for use in potentially explosive atmospheres
(ATEX Directive) Ex II 2 G, Ex d IIB+H2 T6 Gb(Tamb -20°C to +50°C) equipment, by the
application of the following Standards:BS EN 60079-0:2012
Explosive atmospheres - Equipment. General requirements
BS EN 60079-1:2007
Explosive atmospheres. Equipment protection by flameproof
enclosures "d"
IECEx Certificate?
as certified by Notified Body Number 0891 TRaC Global Ltd, UK by EC-Type Examination
Certificate: TRAC13ATEX0046X and IECEx Certificate: IECEx TRC 13.0016X and are
subject to the procedure set out in Annex VII of Directive 94/9/EC and these procedures
are in conformity with the requirements of EN 80079-34 under the supervision of Notified
Body Number 0518, SIRA Certification Service, Rake Lane, Eccleston, Chester, CH4 9JN,
England.
It is ensured through internal measures that the products conform at all times to the
requirements of the current EEC Directives and relevant standards.
Signature:
________________________ Authorised Person
Position:
Director
on behalf of CorDEX Instruments Ltd
Date: 07/10/2014
Product Serial number
Better:Better_Work:CorDEX:03_CorDEX_Products:CorDEX_Products_ToughPIXII:CorDEX_Products_ToughPIXII_ECDeclaration:EC
Declaration of Conformity (TP2410XP)Rev A.docx
RUGGED AUTHORITY
9
Copyright © 2014, CorDEX Instruments Limited.
All other brand and product names are
trademarks of CorDEX Instruments Limited.
Document Reference: TP2400SOM Rev. A