User Manual - Projector Central

LCD Projector
Model 8063/8755C
User's Manual
Operators Guide
Contents:
1. User's Manual– Safety Guide, ..................Page 1-9
2. User's Manual– Operating Guide, .............Page 1-49
3. User's Manual– Technical Guide, ..............Page 1-14
SAFETYINSTRUCTIONS(5A) 03.12.5 8:48 AM ページ 1
Projector
User's Manual - Safety Guide
Thank you for purchasing this projector.
WARNING • Before using, read these user's manuals of this projector to ensure
correct usage through understanding. After reading, store them in a safe place for
future reference. Incorrect handling of this product could possibly result in personal injury
or physical damage. The manufacturer assumes no responsibility for any damage caused by
mishandling that is beyond normal usage defined in these manuals of this projector.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this
manual
• The reproduction, transmission or use of this document or contents is not permitted
without express written authority.
About The Symbols
Various symbols are used in this manual, the user’s manual and on the product itself to
ensure correct usage, to prevent danger to the user and others, and to prevent property
damage. The meanings of these symbols are described below. It is important that you
read these descriptions thoroughly and fully understand the contents.
WARNING
This symbol indicates information that, if ignored, could
possibly result in personal injury or even death due to
incorrect handling.
CAUTION
This symbol indicates information that, if ignored, could
result possibly in personal injury or physical damage due to
incorrect handling.
Typical Symbols
This symbol indicates an additional warning (including cautions). An illustration is
provided to clarify the contents.
This symbol indicates a prohibited action. The contents will be clearly indicated
in an illustration or nearby (the symbol to the left indicates that disassembly is
prohibited).
This symbol indicates a compulsory action. The contents will be clearly
indicated in an illustration or nearby (the symbol to the left indicates that the
power plug should be disconnected from the power outlet).
1
SAFETYINSTRUCTIONS(5A) 03.12.5 8:48 AM ページ 2
Safety Precautions
WARNING
Never use the projector if a problem should occur.
Abnormal operations such as smoke, strange odor, no image, no sound,
excessive sound, damaged casing or elements or cables, penetration of
liquids or foreign matter, etc. can cause a fire or electrical shock.
In such case, immediately turn off the power switch and then disconnect the
power plug from the power outlet. After making sure that the smoke or odor
has stopped, contact your dealer. Never attempt to make repairs yourself
because this could be dangerous.
• The power outlet should be close to the projector and easily accessible.
Use special caution for children and pets.
Incorrect handling could result in fire, electrical shock, injury, burn or
vision problem.
Use special caution in households where children and pets are present.
Do not insert liquids or foreign object.
Penetration of liquids or foreign objects could result in fire or electrical
shock. Use special caution in households where children are present.
If liquids or foreign object should enter the projector, immediately turn off
the power switch, disconnect the power plug from the power outlet and
contact your dealer.
• Do not place the projector in a bathroom.
• Do not expose the projector to rain or moisture.
• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc
on or around the projector.
• Do not place metals, combustibles, etc on or around the projector.
• To avoid penetration of foreign objects, do not put the projector into a case
or bag together with any thing except the accessories of the projector,
signal cables and connectors.
Never disassemble and modify.
The projector contains high voltage components. Modification and/or disassembly
of the projector or accessories could result in fire or electrical shock.
• Never open the cabinet.
• Ask your dealer to repair and clean insider.
Do not give the projector any shock or impact.
If the projector should be shocked and/or broken, it could result in an injury,
and continued use could result in fire or electrical shock.
If the projector is shocked, immediately turn off the power switch,
disconnect the power plug from the power outlet and contact your dealer.
Do not place the projector on an unstable surface.
If the projector should be dropped and/or broken, it could result in an injury,
and continued use could result in fire or electrical shock.
• Do not place the projector on an unstable, slant or vibrant surface such as
a wobbly or inclined stand.
• Use the caster brakes placing the projector on a stand with casters.
• Do not place the projector in the side up position, the lens up position or
the lens down position.
• In the case of a ceiling installation or the like, contact your dealer before
installation.
2
Disconnect the
plug from the
power outlet.
Do not
disassemble.
SAFETYINSTRUCTIONS(5A) 03.12.5 8:48 AM ページ 3
Safety Precautions (continued)
WARNING
Be cautious of High temperatures of the projector.
High temperatures are generated when the lamp is lit. It could result in fire
or burn. Use special caution in households where children are present.
Do not touch about the lens, air fans and ventilation openings during use or
immediately after use, to prevent a burn. Take care of ventilation.
• Keep a space of 30 cm or more between the sides and other objects such
as walls.
• Do not place the projector on a metallic table or anything weak in heat.
• Do not place anything about the lens, air fans and ventilation openings of
the projector.
• Do not use with the ventilation opening facing downwards.
• Never block the air fan and ventilation openings.
• Do not cover the projector with a tablecloth, etc.
• Do not place the projector on a carpet or bedding.
Never look through the lens or openings when the lamp is on.
The powerful light could adversely affect vision.
Use special caution in households where children are present.
Use only the correct power cord and the correct power outlet.
Incorrect power supply could result in fire or electrical shock.
• Use only the correct power outlet depending on the indication on the
projector and the safety standard.
• The enclosed power cord must be used depending on the power outlet to
be used.
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical
shock.
• Do not touch the power cord with a wet hand.
• Check that the connecting portion of the power cord is clean (with no
dust), before using. Use a soft and dry cloth to clean the power plug.
• Insert the power plug into a power outlet firmly. Avoid using a loose,
unsound outlet or contact failure.
Be sure to connect with ground wire.
Connect the ground terminal of AC inlet of this unit with the ground
terminal provided at the building using the correct power cord; otherwise,
fire or electric shock can result.
• Don’t take the core of power cord away.
Surely connect
the ground wire.
3
SAFETYINSTRUCTIONS(5A) 03.12.5 8:48 AM ページ 4
Safety Precautions (continued)
WARNING
Be careful in handling the light source lamp.
The projector uses a high-pressure mercury glass lamp made of glass. The
lamp can break with a loud bang, or burn out. When the bulb bursts, it is
possible for shards of glass to fly into the lamp housing, and for gas
containing mercury to escape from the projector’s vent holes.
Please carefully read the section “Lamp”.
Be careful in handling the power cord and external connection cables.
If you keep using a damaged the power cord or cables, it can cause a fire or
electrical shock. Do not apply too much heat, pressure or tension to the
power cord and cables.
If the power cord or cables is damaged (exposed or broken core wires, etc.),
contact your dealer.
• Do not place the projector or heavy objects on the power cord and cables.
Also, do not place a spread, cover, etc, over them because this could result
in the inadvertent placing of heavy objects on the concealed power cord or
cables.
• Do not pull the power cord and cables. When connecting and
disconnecting the power cord or cables, do it with your hand holding the
plug or connector.
• Do not place the cord near the heater.
• Avoid bending the power cord sharply.
• Do not attempt to work on the power cord.
Be careful in handling the battery of the remote control.
Incorrect handling of the battery could result in fire or personal injury. The
battery may explode if not handled properly.
• Keep the battery away from children and pets. If swallowed consult a
physician immediately for emergency treatment.
• Do not allow the battery in a fire or water.
• Avoid fire or high-temperature environment.
• Do not hold the battery with the metallic tweezers.
• Keep the battery in a dark, cool and dry play.
• Do not short circuit the battery.
• Do not recharge, disassemble or solder the battery.
• Do not give the battery a physical impact.
• Use only the battery specified in the other manual of this projector.
• Make sure the plus and minus terminals are correctly aligned when
loading the battery.
• If you observe a leakage of the battery, wipe out the flower and then
replace the battery. If the flower adheres your body or clothes, rinse well
with water.
• Obey the local laws on disposing the battery.
4
SAFETYINSTRUCTIONS(5A) 03.12.5 8:48 AM ページ 5
Safety Precautions (continued)
CAUTION
Be careful in moving the projector.
Neglect could result in an injury or damage.
• Do not move the projector during use. Before moving, disconnect the
power cord and all external connections, and close the slide lens door or
attach the lens cap.
• Avoid any impact or shock to the projector.
• Do not drag the projector.
• For moving the projector, use the enclosed case or bag if provided.
Do not put anything on top of the projector.
Placing anything on the projector could result in loss of balance or falling,
and cause an injury or damage. Use special caution in households where
children are present.
Do not attach anything other than specified things to the projector.
Neglect could result in an injury or damage.
• Some projector has a screw thread in a lens part. Do not attach anything
other than specified options (such as conversion lens) to the screw thread.
Avoid a smoky, humid or dusty place.
Placing the projector in a smoke, a highly humid, dusty place, oily soot or
corrosive gas could result in fire or electrical shock.
• Do not place near the smoking space, the kitchen or a humidifier.
Take care of the air filter to normal ventilate.
The air filter should be cleaned periodically. If the air filter becomes
clogged by dust or the like, internal temperature rises and could cause
malfunction. The projector may display the message such as “CHECK THE
AIR FLOW” or turn off the projector, to prevent the internal heat level
rising.
• When the indicators or a message prompts you to clean the air filter, clean
the air filter as soon as possible.
• If the soiling will not come off the air filter, or it becomes damaged,
replace the air filter.
• Use the air filter of the specified type only. Please order the air filter
specified in the other manual of this projector to your dealer.
• When you replace the lamp, replace also the air filter. The air filter may be
attached when you buy a replacement lamp for this projector.
• Do not turn on the projector without air filter.
Avoid a high temperature environment.
The heat could have adverse influence on the cabinet of the projector and
other parts. Do not place the projector, the remote control and other parts in
direct sunlight or near a hot object such as heater, etc.
Remove the power cord for complete separation.
• For safety purposes, disconnect the power cord if the projector is not to be
used for prolonged periods of time.
• Before cleaning, turn off and unplug the projector. Neglect could result in
fire or electrical shock.
Disconnect the
plug from the
power outlet.
5
SAFETYINSTRUCTIONS(5A) 03.12.5 8:48 AM ページ 6
Safety Precautions (continued)
CAUTION
Ask your dealer to cleaning inside of the projector about every two
years.
Accumulations of dust inside the projector cause result in fire or
malfunction. Cleaning inside is more effective if performed before every
humid periods such as rainy season.
• Do not clean inside yourself because it is dangerous.
NOTE
Do not give the remote control any physical impact.
A physical impact could cause damage or malfunction of the remote control.
• Take care not to drop the remote control.
• Do not place the projector or heavy objects on the remote control.
Take care of the lens.
• Close the slide lens door or attach the lens cap to prevent the lens surface being
scratched when the projector is not used.
• Do not touch the lens to prevent fog or dirt of the lens that cause deterioration of display
quality.
• Use commercially available lens tissue to clean the lens (used to clean cameras,
eyeglasses, etc.). Be careful not to scratch the lens with hard objects.
Take care of the cabinet and the remote control.
Incorrect care could have adverse influence such as discoloration, peeling paint, etc.
• Use a soft cloth to clean the cabinet and control panel of the projector and the remote
control. When excessively soiled dilute a neutral detergent in water, wet and wring out the
soft cloth and afterward wipe with a dry soft cloth. Do not use undiluted detergent
directly.
• Do not use an aerosol sprays, solvents, volatile substances or abrasive cleaner.
• Before using chemical wipes, be sure to read and observe the instructions.
• Do not allow long-term close contact with rubber or vinyl.
About bright spots or dark spots.
Although bright spots or dark spots may appear on the screen, this is a unique characteristic of
liquid crystal displays, and such do not constitute or imply a machine defect.
Be careful of printing of the LCD panel.
If the projector continues projecting a still image, inactive images or 16:9 aspect images
in case of 4:3 panel, etc., for long time, the LCD panel might possibly be printed.
In such a case, please make the projector project a whole white screen for 1 hour or more.
You can use the BLANK function of the projector.
About consumables.
Lamp, LCD panels, polarizors and other optical components, and air filter and cooling
fans have a different lifetime in each. These parts may need to be replaced after a long
usage time, even if one year has not passed since the beginning of using. For more details,
please consult your dealer.
6
SAFETYINSTRUCTIONS(5A) 03.12.5 8:48 AM ページ 7
Safety Precautions (continued)
NOTE
Avoid strong rays.
Any strong ray (such as direct rays of the sun or room lighting) onto the remote control
sensors could invalidate the remote control.
Avoid radio interference.
Any interfering radiation could cause disordered image or noises.
• Avoid radio generator such as a mobile telephone, transceiver, etc. around the projector.
About displaying characteristic.
The display condition of the projector (such as color, contrast, etc.) depends on
characteristic of the screen, because the projector uses a liquid crystal display panel. The
display condition can differ from the display of CRT.
• Do not use a polarized screen. It can cause red image.
Turn the power on/off in right order.
To prevent any trouble, turn on/off the projector in right order mentioned below unless
specifying.
• Power on the projector before the computer or video tape recorder.
• Power off the projector after the computer or video tape recorder.
Take care not to fatigue your eyes.
Rest the eyes periodically.
Set the sound volume at a suitable level to avoid bothering other people.
• It is better to keep the volume level low and close the windows at night to protect the
neighborhood environment.
Connecting with notebook computer
When connecting with notebook computer, set to valid the RGB external image output
(setting CRT display or simultaneous display of LCD and CRT).
Please read instruction manual of the notebook for more information.
7
SAFETYINSTRUCTIONS(5A) 03.12.5 8:48 AM ページ 8
Lamp
WARNING
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
The projector uses a high-pressure mercury glass lamp. The lamp can break with a
loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.
Note that each lamp has a different lifetime, and some may burst or burn out soon after
you start using them. In addition, when the bulb bursts, it is possible for shards of
glass to fly into the lamp housing, and for gas containing mercury to escape from the
projector’s vent holes.
About disposal of a lamp • This product contains a mercury lamp; do not put in trash.
Dispose of in accord with environmental laws.
For lamp recycling, go to www.lamprecycle.org. (in USA)
For product disposal, contact your local government agency or www.eiae.org (in the
US) or www.epsc.ca (in Canada).
For more information, call your dealer.
Disconnect the
plug from the
power outlet
• If the lamp should break (it will make a loud bang when it does), unplug
the power cord from the outlet, and make sure to request a replacement
lamp from your local dealer. Note that shards of glass could damage the
projector’s internals, or cause injury during handling, so please do not try
to clean the projector or replace the lamp yourself.
• If the lamp should break (it will make a loud bang when it does),
ventilate the room well, and make sure not to breathe the gas that comes
out of the projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, make sure the power switch is off and the
power cable is not plugged in, then wait at least 45 minutes for the lamp
to cool sufficiently. Handling the lamp while hot can cause burns, as well
as damaging the lamp.
• Do not open the lamp cover while the projector is suspended from above.
This is dangerous, since if the lamp’s bulb has broken, the shards will
fall out when the cover is opened. In addition, working in high places is
dangerous, so ask your local dealer to have the lamp replaced even if the
bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose screws
could result in damage or injury.
• Use the lamp of the specified type only.
• If the lamp breaks soon after the first time it is used, it is possible that
there are electrical problems elsewhere besides the lamp. If this happens,
contact your local dealer or a service representative.
• Handle with care: jolting or scratching could cause the lamp bulb to burst
during use.
• If the indicators or a message prompts you to replace the lamp (see the
section “Related Messages” and “Regarding the indicator Lamps”),
replace the lamp as soon as possible. Using the lamp for long periods of
time, or past the replacement date, could cause it to burst. Do not use old
(used) lamps; this is a cause of breakage.
8
SAFETYINSTRUCTIONS(5A) 03.12.5 8:48 AM ページ 9
Regulatory Notices
FCC Statement Warning
WARNING: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC
(Federal Communication Commission) equipment provided that the following conditions
are met. Some cables have to be used with the core set. Use the accessory cable or a
designated-type cable for the connection. For cables that have a core only at one end,
connect the core to the projector.
CAUTION: Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
For the Customers in CANADA
NOTICE: This Class B digital apparatus complies with Canadian ICES-003.
Warranty And After-Service
Unless seen any abnormal operations (mentioned with the first paragraph of WARNING
in this manual), when a problem occurs with the equipment, first refer to the
“Troubleshooting” section of the “User’s manual – Operating Guide”, and run through the
suggested checks.
If this does not resolve the problem contact your dealer or service company. They will tell
you what warranty condition is applied.
9
Projector
8063/8755C
ENGLISH
User's Manual – Operating Guide
Thank you for purchasing this projector.
WARNING ►Before using, read the "User's Manual - Safety Guide" and
these manuals to ensure correct usage through understanding. After reading,
store them in a safe place for future reference.
About this manual
Various symbols are used in this manual. The meanings of these symbols are
described below.
WARNING This symbol indicates information that , if ignored, could possibly
result in personal injury or even death due to incorrect handling.
CAUTION This symbol indicates information that , if ignored, could result
possibly in personal injury or physical damage due to incorrect
handling.
 Please refer to the pages written following this symbol.
NOTE • The information in this manual is subject to chance without notice.
• The manufacture assumes no responsibility for any errors that may appear in this manual.
• The reproduction, transmission or use of this document or contents is not permitted without
express written authority.
Trademark acknowledgment
• VGA and XGA are registered trademarks of the International Business Machines
Corporation.
• Apple and Mac are registered trademarks of the Apple Computer, Inc.
• VESA and SVGA are trademarks of the Video Electronics Standard Association.
• Windows is a registered trademark of the Microsoft Corporation.
• Internet Explorer is a trademark of the Microsoft Corporation.
All other trademarks are the property of their respective owners.
1
Contents
Contents

About this manual . . . . . . . . . . 1
Contents . . . . . . . . . . . . . . . . . 2
Projector features . . . . . . . . . . 3
Preparations . . . . . . . . . . . . . . 3
Part names . . . . . . . . . . . . . . . 4
Projector . . . . . . . . . . . . . . . . . . . . . 4
Controls . . . . . . . . . . . . . . . . . . . . . . 5
Remote control . . . . . . . . . . . . . . . . 5
Setting up . . . . . . . . . . . . . . . . 6
Arrangement . . . . . . . . . . . . . . . . . . 7
Adjusting the projector's elevator . . 8
About the filter cover for bottom-up use . . 9
Connecting your devices . . . . . . . . 10
Connecting power supply . . . . . . . 13
Remote control . . . . . . . . . . . 14
Putting batteries . . . . . . . . . . . . . . 14
Using the remote control . . . . . . . . 15
Power on/off . . . . . . . . . . . . . 16
Turning on the power. . . . . . . . . . . 16
Turning off the power . . . . . . . . . . . 16
Operating . . . . . . . . . . . . . . . 17
Adjusting the volume . . . . . . . . . . . 17
Temporarily muting the sound . . . . 17
Selecting an input signal . . . . . . . . 17
Searching an input signal . . . . . . . 18
Selecting the aspect ratio . . . . . . . 18
Adjusting the zoom and focus . . . . 18
Using the automatic adjustment feature . 19
Adjusting the position . . . . . . . . . . 19
Correcting the keystone distortions 19
Using the magnify feature . . . . . . . 20
Freezing the screen . . . . . . . . . . . . 20
Temporarily blanking the screen . . 20
Operating the computer screen . . . 21
Multifunctional settings . . . . 22
Using the menu function . . . . . . . . 22
EASY Menu . . . . . . . . . . . . . . . . . . 23
Aspect, Keystone, Mode, Bright,
Contrast, Color, Tint, Sharpness,
Whisper, Mirror, Reset, Filter time,
Language, Go to advanced menu
2

PICTURE Menu . . . . . . . . . . . . . . . 25
Bright, Contrast, Gamma, Color temp,
Color, Tint, Sharpness, Progressive,
My memory
IMAGE Menu . . . . . . . . . . . . . . . . . 28
Aspect, Over scan, V. position, H.
position, H. phase, H. size, Auto adjust
INPUT Menu . . . . . . . . . . . . . . . . . 30
Color space, Component, Video format,
Frame lock, Information
SETUP Menu. . . . . . . . . . . . . . . . . 32
Keystone, Whisper, Mirror, Volume
SCREEN Menu . . . . . . . . . . . . . . . 33
Language, Menu position, OSD bright,
Blank, Start up, MyScreen,
MyScreen lock, Message
OPTION Menu . . . . . . . . . . . . . . . . 36
Search, Auto off, Lamp time, Filter time,
Service
Maintenance . . . . . . . . . . . . .
Lamp . . . . . . . . . . . . . . . . . . . . . . .
Air filter . . . . . . . . . . . . . . . . . . . . .
Other care . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . .
Related messages . . . . . . . . . . . . .
Regarding the indicator lamps . . . .
Phenomena that may easily be
mistaken for machine defects . . . .
Warranty and after-service . . .
Specifications . . . . . . . . . . . .
38
38
40
41
42
42
44
46
48
48
Projector features / Preparations
This projector is used to project various computer signals as well as NTSC / PAL
/ SECAM video signals onto a screen. It requires just a little space for installation
and gets a large image from short distance.
 High Brightness
Newly developed 165W UHB (Ultra High Brightness) lamp gives you a higher
brightness image on a screen. The image can be still kept as bright and clean
enough for use in bright rooms.
 Low Noise
WHISPER mode is equipped for reducing acoustic noise to realize quieter
operation. It is perfect for use in low luminance rooms where low noise is more
important than brightness.
 Rich Connectivity
This projector has a variety of I/O ports. It can be easily connected to many
signal sources like PC, DVD and so on. The rich connectivity provides you
more options to make your presentation impressive.
 Compact Body
Even with its many features, this projector is extremely compact and slim,
which gives you more flexibility and usability to use it where you want.
Preparations
About contents of package
Please see the "Contents of package" of the "User's manual - Quick guide". Your
projector should come with the items shown there. Contact immediately your
dealer if anything is missing.
NOTE • Keep the original packing materials for future reshipment. For
moving the projector, be sure to use the original packing material. Use special
caution for the lens part.
3
ENGLISH
Projector features
Part names
Part names
Remote sensor (15)
Projector
Zoom knob (18)
Speaker (6)
Focus ring (18)
Vent (6)
Elevator button (8)
Lens cover (16)
(Slide door)
Elevator foot (8)
Front-Right side
Lens (16)
Lamp cover
(Lamp unit is inside.)
(38)
Filter cover (40)
(Air filter and intake vent
are inside.)
Bottom side
Power switch (16)
Control buttons
(See the following page.)
(5)
AC inlet (13)
Elevator button (8)
Ports
(See below.)
Elevator foot (8)
Vent (6)
Rear-Left side
AUDIO OUT port (11)
Restart switch (*) (46)
RGB IN1 port (11)
AUDIO IN1 port (11)
S-VIDEO port (12)
COMPONENT
VIDEO ports (12)
Y
CB/PB
CR/PR
VIDEO port (12)
AUDIO IN2 port (11)
RGB IN2 port (11)
AUDIO IN1
Y
AUDIO OUT
RGB IN1
CB/PB
VIDEO
CR/PR S-VIDEO
COMPONENT VIDEO
RGB IN2
RGB OUT
RGB OUT port (11)
CONTROL port (11)
AUDIO IN2
USB
CONTROL
Kensington lock slot
Ports
USB port (11)
NOTE (*) About Restart switch: This Projector is controlled by an internal
microprocessor. Under certain exceptional circumstances, the projector may not
operate correctly and the microprocessor will need to be reset. In such a case,
please push the Restart switch by using a cocktail stick or similar and before
turning on again, make the projector cool down at least 10 minutes without
operating. Only push the Restart switch in these exceptional instances.
4
Part names
Control buttons
LAMP indicator (44)
TEMP indicator (44)
POWER indicator (16)
ENGLISH
LAMP
TEMP
POWER
STANDBY/ON
INPUT
MENU
STANDBY/ON button (16)
Cursor buttons
▲,▼,◄,► (22)
INPUT button (17)
Remote control
SEARCH button (18)
RGB button (17)
VIDEO button (17)
STANDBY/ON
VIDEO
ASPECT button (18)
RGB
AUTO button (19)
AUTO
BLANK
HOME
PAGE UP
VOLUME
VOLUME button (17)
END
PAGE DOWN
MUTE
PAGE UP button (21)
ASPECT
BLANK button (20)
HOME button (21)
MAGNIFY (20)
ON button
OFF button
MAGNIFY
ON
OFF
FREEZE
KEYSTONE
END button (21)
Cursor buttons
▲,▼,◄,►(22)
ESC button (22)
MUTE button (17)
PAGE DOWN button (21)
FREEZE button (20)
POSITION button (19)
STANDBY/ON button (16)
SEARCH
MENU
POSITION
MENU button (22)
ENTER
ESC
KEYSTONE button (19)
RESET
ENTER button (22)
RESET button (22)
5
Setting up
Setting up
WARNING ►Place the projector in a stable position horizontally. A fall or
a turnover could cause an injury and/or damage to the projector. Then using
damaged projector could result in a fire and/or an electric shock.
• Don’t place the projector on an unstable, slant or vibrant surface such as a
wobbly or inclined stand.
• Do not place the projector in the side/front/rear-up position, except care of the
air filter.
• For the projector installed bottom-up, use the accessory filter cover for bottomup use. And in the case of a ceiling installation or the like, contact your dealer
before installation.
►Place the projection in a cool place, and pay attention enough to ventilation.
The high temperature of the projector could cause a fire, a burn and/or
malfunction to the projector.
• Don’t stop up, block and cover the projector's vents.
• Keep a space of 30 cm or more between the sides and other objects such as
walls.
• Don’t place the projector on a metallic thing or anything weak in heat.
• Don’t place the projector on a carpet, cushion or bedding.
• Don’t place the projector in direct sunlight or near a hot object such as heater.
• Put nothing about lens and vents of the projector. Put nothing on the projector.
• Put nothing that is sucked or sticks to the bottom of projector. This projector
has some intake vents also on the bottom.
►Do not place the projector on the place that gets wet. Damping the projector
or inserting liquid in the projector could cause a fire, an electric shock and/or
malfunction to the projector.
• Don’t place the projector in a bathroom or the outdoors.
• Put nothing containing the liquid near the projector.
CAUTION ►Avoid a smoky, humid or dusty place. Placing the projector
in such place could cause a fire, an electric shock and/or malfunction to the
projector.
• Don’t place the projector near a humidifier, a smoking space or a kitchen.
• Put nothing containing the liquid near the projector.
►Adjust the direction of the projector to keep light from directly hitting the
projector's remote sensor.
6
Setting up
Arrangement
ENGLISH
Refer to the illustrations and tables below to determine the screen size and projection
distance.
The values shown in the table are calculated for a full size screen: 1280 x 720
(a) The screen size (diagonal)
(b) Distance from the projector to the screen (±10%)
(c) The height of the screen (±10%)
(b)
4:3
(a)
16:9
(c) up
(a)
(c) down
At 4:3 screen
(a) Screen size (b) Projection distance [m (inch)]
[inch (m)]
min.
max.
30
40
50
60
70
80
90
100
120
150
200
250
300
(0.8)
(1.0)
(1.3)
(1.5)
(1.8)
(2.0)
(2.3)
(2.5)
(3.0)
(3.8)
(5.1)
(6.4)
(7.6)
0.9
1.2
1.5
1.8
2.1
2.4
2.7
3.1
3.7
4.6
6.1
7.6
9.2
(35)
(47)
(59)
(72)
(84)
(96)
(108)
(120)
(144)
(181)
(242)
(303)
(363)
1.1
1.4
1.8
2.2
2.5
2.9
3.3
3.6
4.4
5.5
7.3
9.2
11.0
(42)
(56)
(71)
(85)
(100)
(114)
(129)
(143)
(172)
(216)
(288)
(361)
(433)
At 16:9 screen
(a) Screen size (b) Projection distance [m (inch)]
[inch (m)]
min.
max.
30
40
50
60
70
80
90
100
120
150
200
250
300
(0.8)
(1.0)
(1.3)
(1.5)
(1.8)
(2.0)
(2.3)
(2.5)
(3.0)
(3.8)
(5.1)
(6.4)
(7.6)
1.0
1.3
1.6
2.0
2.3
2.7
3.0
3.3
4.0
5.0
6.7
8.4
10.1
(38)
(52)
(65)
(78)
(91)
(105)
(118)
(131)
(158)
(197)
(264)
(330)
(396)
1.2
1.6
2.0
2.4
2.8
3.2
3.6
4.0
4.8
6.0
8.0
10.0
12.0
(46)
(62)
(77)
(93)
(109)
(125)
(140)
(156)
(188)
(235)
(314)
(393)
(472)
(c) Screen height [cm (inch)]
down
up
5
6
8
9
11
12
14
15
18
23
30
38
46
(2)
(2)
(3)
(4)
(4)
(5)
(5)
(6)
(7)
(9)
(12)
(15)
(18)
41
55
69
82
96
110
123
137
165
206
274
343
411
(16)
(22)
(27)
(32)
(38)
(43)
(49)
(54)
(65)
(81)
(108)
(135)
(162)
(c) Screen height [cm (inch)]
down
up
-1
-2
-2
-2
-3
-3
-4
-4
-5
-6
-8
-10
-12
(0)
(-1)
(-1)
(-1)
(-1)
(-1)
(-1)
(-2)
(-2)
(-2)
(-3)
(-4)
(-5)
39
51
64
77
90
103
116
129
154
193
257
322
386
(15)
(20)
(25)
(30)
(35)
(41)
(46)
(51)
(61)
(76)
(101)
(127)
(152)
7
Setting up
Adjusting the projector's elevator
WARNING ►Do not adjust the projector’s elevator during use or
immediately after use. Handling while the projector is in a high temperature
could cause a burn and/or malfunction to the projector.
CAUTION ►If you press the elevator button without holding the projector,
the projector might crash down, overturn, smash your fingers and possibly
result in malfunction. To prevent damaging the projector and injuring yourself,
always hold the projector whenever using the elevator buttons to adjust the
elevator feet.
►Except for inclining by the elevator feet adjustment, place the projector
horizontally.
You can use the elevator feet to make adjustments if the surface on which you
need to set the projector is uneven or if you otherwise need to adjust the angle of
projection. The adjustment range of the elevator feet is 0 to 9 degrees.
Elevator feet
Elevator button
making sure that the projector is cool adequately, press and hold in the
1. After
elevator buttons while holding the projector.
2.
3.
8
The elevator buttons and the elevator feet are on the both sides.
Raise or lower the projector to the desired height and the release the elevator
buttons.
When you release the elevator buttons, the elevator feet will lock into position.
As necessary, you can also finely adjust the height of the projector by twisting
the elevator feet by hand.
Setting up
WARNING ►Do not replace the filter cover during use or immediately
after use. While the projector connects with a power supply, or the projector is
in a high temperature state, handling could cause an electric shock, a fire, a
burn and/or malfunction to the projector.Before handling, make sure the power
switch is off and the power cord is not plugged in, then wait at least 45 minutes.
When the projector is installed bottom up, please use the accessory filter cover
for bottom-up use. It is higher than usual filter cover, to keep the space for intake
ventilation. Please change in the following procedure.
Filter cover’s knob
Filter cover’s knob
To remove
Filter cover
To set
Filter cover for bottom-up use
making sure that the projector is cool adequately, slowly turn the
1. After
projector so that the lens-side is facing up. Please be careful for a projector
not to fall. While the projector is placed lens-side up, hold the projector.
Putting a finger on the filter cover’s knob, slide the filter cover in the direction
of the arrow to remove it.
Replace the filter cover for bottom-up use and snap it back into place.
2.
3.
4. Slowly turn the projector so that the top is facing up.
9
ENGLISH
About the filter cover for bottom-up use
Setting up
Connecting your devices
CAUTION ►Turn off all devices prior to connecting them to the projector.
Attempting to connect a live device to the projector may generate extremely
loud noises or other abnormalities that may result in malfunction and/or damage
to the device and/or projector.
►Use the accessory cable or a designated-type cable for the connection.
Some cables have to be used with core set. A too long cable may cause a
certain picture degradation. Please consult with your dealer for details. For
cables that have a core only at one end, connect the core to the projector.
►Make sure that you connect devices to the correct port. Incorrect connection
may result in malfunction and/or damage to the device and/or projector.
NOTE • Whenever attempting to connect a laptop computer to the projector, be sure
to activate the laptop’s RGB external image output (set the laptop to CRT display or to
simultaneous LCD and CRT display). For details on how this is done, please refer to the
instruction manual of the corresponding laptop computer.
• Secure the screws on the connectors and tighten.
• Some computers may have multiple display screen modes. Use of some of these
modes will not be possible with this projector.
• For some RGB signal modes, the optional Mac adapter is necessary.
• When the image resolution is changed on a computer, depending on an input,
automatic adjust function may take some time and may not be completed. In this case,
you may not be able to see a check box to select “Yes/No” for the new resolution on
Windows. Then the resolution will go back to the original. It might be recommended to
use other CRT or LCD monitors to change the resolution.
About Plug-and-Play capability
Plug-and-Play is a system composed of the computer, its operating system and
peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC
2B. Plug-and-Play can be achieved by connecting this projector to computers that are
VESA DDC (display data channel) compatible.
• Please take advantage of this function by connecting the accessory RGB cable to the
RGB IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other
type of connection is attempted.
• Please use the standard drivers in your computer as this projector is a Plug-and-Play
monitor.
10
Examples of connection with a computer
* AUDIO IN1
is linked to
RGB IN1.
RGB cable
Stereo mini
audio cable
AUDIO IN1
Y
AUDIO OUT
RGB IN1
RGB IN2
RGB OUT
RGB IN2
RGB OUT
RGB IN2
RGB OUT
RGB IN2
RGB OUT
CB/PB
RGB out RS-232C Audio out USB(A)
VIDEO
AUDIO IN2
CR/PR S-VIDEO
USB
COMPONENT VIDEO
CONTROL
RS-232C
cable
USB
cable
AUDIO IN1
Y
AUDIO OUT
RGB out
Audio out
RGB IN1
CB/PB
VIDEO
AUDIO IN2
CR/PR S-VIDEO
USB
COMPONENT VIDEO
CONTROL
Stereo mini
audio cable
RGB cable
Connecting to a monitor (output)
AUDIO IN1
Y
AUDIO OUT
RGB IN1
CB/PB
RGB in
VIDEO
AUDIO IN2
CR/PR S-VIDEO
USB
COMPONENT VIDEO
CONTROL
RGB cable
Connecting to a speaker with amplifier (output)
AUDIO IN1
Y
AUDIO OUT
Audio in
RGB IN1
CB/PB
VIDEO
AUDIO IN2
CR/PR S-VIDEO
COMPONENT VIDEO
USB
CONTROL
Stereo mini
audio cable
11
ENGLISH
Setting up
Setting up
Examples of connection with a VCR/DVD player
AUDIO IN1
Audio out
Video out
Y
AUDIO OUT
RGB IN1
RGB IN2
RGB OUT
RGB IN2
RGB OUT
RGB IN2
RGB OUT
RGB IN2
RGB OUT
RGB IN2
RGB OUT
CB/PB
VIDEO
AUDIO IN2
CR/PR S-VIDEO
USB
COMPONENT VIDEO
CONTROL
Video cable
Stereo mini audio cable
AUDIO IN1
Audio out
S-Video out
Y
AUDIO OUT
RGB IN1
CB/PB
VIDEO
AUDIO IN2
CR/PR S-VIDEO
USB
COMPONENT VIDEO
CONTROL
S-Video cable
Stereo mini audio cable
Component video out
Y
Audio out C /P
B B
CR/PR
Component video cable
AUDIO IN1
Y
AUDIO OUT
RGB IN1
CB/PB
VIDEO
AUDIO IN2
CR/PR S-VIDEO
USB
COMPONENT VIDEO
CONTROL
Stereo mini audio cable
AUDIO IN1
Y
AUDIO OUT
Component video out
Y
Audio out C /P
B B
CR/PR
Component video cable
RGB IN1
CB/PB
VIDEO
AUDIO IN2
CR/PR S-VIDEO
AUDIO IN1
COMPONENT VIDEO
USB
CONTROL
Y
AUDIO OUT
RGB IN1
CB/PB
VIDEO
CR/PR S-VIDEO
COMPONENT VIDEO
AUDIO IN2
USB
CONTROL
Stereo mini audio cable
12
Setting up
WARNING ►Please use extra caution when connecting the power cord as
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact
your dealer to newly get correct one.
• Only plug the power cord into an outlet rated for use with the power cord's
specified voltage range.
• Never modify the power cord. Never attempt to defeat the ground connection
of the three-pronged plug.
AC inlet
Connector
of the power cord
the connector of the power cord to the
1. Connect
AC inlet of the projector.
2. Firmly plug the power cord's plug into the outlet.
13
ENGLISH
Connecting power supply
Remote control
Remote control
Putting batteries
WARNING ►Always handle the batteries with care and use them only as
directed. Improper use may result in battery explosion, cracking or leakage,
which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.
• Make sure the plus and minus terminals are correctly aligned when loading a
battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
• Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry
play.
• If you observe a leakage of a battery, wipe out the flower and then replace
a battery. If the flower adheres your body or clothes, rinse well with water
immediately.
Remove the battery cover.
1. Slide
back and remove the battery cover in the direction of the arrow.
Insert the batteries.
2. Align
and insert the two AA batteries according to their plus and minus
3.
14
terminals as indicated in the remote control.
Close the battery cover.
Replace the battery cover in the direction of the arrow and snap it back into
place.
Remote control
Using the remote control
ENGLISH
CAUTION ►Be careful in handling the remote control.
• Do not drop or otherwise expose the remote control to physical impact.
• Do not get the remote control wet or place it on wet objects. Doing so may
result in malfunction.
• Remove the batteries from the remote control and store them in a safe place if
you won’t be using the remote control for an extended period.
• Replace the batteries whenever the remote control starts to malfunction.
• When strong lights, such as direct sunlight or light from an extremely close
range (such as from an inverter fluorescent lamp), hit the projector’s remote
sensor, the remote control may cause to function. Adjust the direction of the
projector to keep light from directly hitting the projector’s remote sensor.
The remote control works with the projector’s remote sensor.
30º
approx. 3 meters
30º
• The range of the remote sensor is 3 meters with a 60- degree range (30 degrees
to the left and right of the remote sensor).
• Also a remote signal reflected in the screen etc. may be available. If it is difficult
to send a remote signal to the sensor directly, please try.
• Since the remote control uses infrared light to send signals to the projector
(Class1 LED), be sure to use the remote control in an area free from obstacles
that could block the remote control’s output signal to the projector.
15
Power on/off
Power on/off
WARNING ►When the power is on, a strong light is emitted. Do not look
into the lens or vents of the projector.
NOTE • Turn the power on/off in right order. Please power on the projector
before the connected devices. Power off the projector after the connected devices.
LAMP
TEMP
STANDBY/ON
VIDEO
RGB
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
ASPECT
MAGNIFY
SEARCH
ON
OFF
FREEZE
KEYSTONE
INPUT
STANDBY/ON
MENU
MENU
POSITION
ENTER
ESC
POWER
indicator
POWER
STANDBY/ON
button
RESET
Power switch
Turning on the power
sure that the power cord is firmly and correctly
1. Make
connected to the projector and outlet.
the lens cover, and set the power switch to the
2. Open
ON position.
POWER
(Solid orange)
POWER
(Blinking green)
POWER
The power indicator will light to solid orange. Then wait
several seconds because buttons may not function for
(Solid green)
these several seconds.
Press the STANDBY/ON button on the projector or remote control.
The projector lamp will light up and the POWER indicator will begin blinking
green. When the power is completely on, the indicator will stop blinking light
green.
To display the picture, select an input signal according to the section "Selecting an
input signal" (17).
3.
Turning off the power
the STANDBY/ON button on the projector or
1. Press
remote control.
Power off?
The message "Power off?" will appear on the screen for
POWER
approximately 5 seconds.
(Blinking orange)
Press the STANDBY/ON button on the projector or
remote control again while the message is visible.
POWER
The projector lamp will go off, and the POWER indicator
will begin blinking orange.
(Solid orange)
Then the POWER indicator will stop blinking and light to
solid orange when the lamp cooling is complete.
Make sure that the power indicator lights to solid orange, set the power switch
to the OFF position. The POWER indicator will go off. Close the lens cover.
2.
3.
16
Operating
Operating
1.
STANDBY/ON
VIDEO
RGB
SEARCH
STANDBY/ON
ASPECT
BLANK
AUTO
VIDEO
SEARCH
RGB
Press the VOLUME button on the remote control.
A dialog will appear on the screen to aid you in adjusting
the volume.
Use the cursor buttons ▲/▼ to adjust the volume.
To close the dialog and complete the operation, press the VOLUME button
again. Even if you don’t do anything, the dialog will automatically disappear
after a few seconds.
MAGNIFY
HOME
PAGE UP
END
PAGE DOWN
VOLUME
ON
MUTE
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ASPECT
OFF
FREEZE
KEYSTONE
MAGNIFY
MENU
POSITION
ON
ENTER
RESET
ESC
MUTE
OFF
2.
FREEZE
KEYSTONE
MENU
POSITION
ENTER
RESET
ESC
Temporarily muting the sound
1.
STANDBY/ON
VIDEO
SEARCH
RGB
STANDBY/ON
VIDEO
RGB
ASPECT
SEARCH
BLANK
AUTO
ASPECT
BLANK
AUTO
Press the MUTE button on the remote control.
A dialog will appear on the screen indicating that you have
muted the sound.
To restore the sound, press the MUTE or VOLUME button.
Even if you don’t do anything, the dialog will automatically disappear after a few
seconds.
MAGNIFY
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
ON
MAGNIFY
OFF
FREEZE
HOME
PAGE UP
END
PAGE DOWN
VOLUME
KEYSTONE
ON
MENU
POSITION
MUTE
OFF
ENTER
RESET
ESC
FREEZE
KEYSTONE
MENU
POSITION
ENTER
RESET
ESC
Selecting an input signal
LAMP
TEMP
the INPUT button on the projector.
1. Press
Each time you press the button, the projector switches its
POWER
STANDBY/ON
INPUT
MENU
input port as below.
RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO
the RGB button on the remote control to select an
1. Press
input port for RGB signal.
STANDBY/ON
VIDEO
RGB
SEARCH
HOME
PAGE UP
END
PAGE DOWN
ASPECT
MAGNIFY
BLANK
AUTO
VOLUME
ON
STANDBY/ON
MUTE
Each time you press the button, the projector switches its
RGB input port as below.
RGB IN1  RGB IN2
● When the TURN ON is selected to the item SEARCH of OPTION menu (36),
the projector selects the RGB IN1 port at first. If no input is detects at the RGB
IN1 port, projector will check the RGB IN2 port.
OFF
VIDEO
FREEZE
RGB
SEARCH
KEYSTONE
MENU
POSITION
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ASPECT
ENTER
RESET
ESC
MAGNIFY
ON
MUTE
OFF
FREEZE
KEYSTONE
MENU
POSITION
ENTER
the VIDEO button on the remote control to select
1. Press
an input port for video signal.
Each time you press the button, the projector switches its
video input port as below.
COMPONENT VIDEO  S-VIDEO  VIDEO
RESET
ESC
STANDBY/ON
VIDEO
RGB
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ASPECT
MAGNIFY
ON
STANDBY/ON
MUTE
OFF
VIDEO
FREEZE
RGB
SEARCH
KEYSTONE
MENU
POSITION
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ASPECT
ENTER
ESC
RESET
MAGNIFY
ON
MUTE
OFF
FREEZE
KEYSTONE
● When the TURN ON is selected to the item SEARCH of OPTION menu (36),
the projector selects the COMPONENT VIDEO port at first. If no input is
detected at the COMPONENT VIDEO port, projector will begin to check other
ports.
MENU
POSITION
ENTER
ESC
RESET
17
ENGLISH
Adjusting the volume
Operating
Searching an input signal
STANDBY/ON
VIDEO
RGB
SEARCH
HOME
PAGE UP
END
PAGE DOWN
ASPECT
the SEARCH button on the remote control.
1. Press
The projector will begin to check its input ports in order to
MAGNIFY
BLANK
AUTO
VOLUME
ON
STANDBY/ON
MUTE
VIDEO
OFF
FREEZE
RGB
SEARCH
KEYSTONE
ASPECT
BLANK
AUTO
MENU
POSITION
find any input signals.
Then when an input is found, the projector will stop
searching and display the image. If no signal is found, the projector will return
to the state selected before the operation.
RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO
ENTER
RESET
ESC
MAGNIFY
HOME
PAGE UP
END
PAGE DOWN
VOLUME
ON
MUTE
OFF
FREEZE
KEYSTONE
MENU
POSITION
ENTER
RESET
ESC
Selecting an aspect ratio
the ASPECT button on the remote control.
1. Press
Each time you press the button, the projector switches the mode for aspect
ratio in turn.
 At a RGB signal
NORMAL  4:3  16:9
STANDBY/ON
VIDEO
RGB
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
STANDBY/ON
ASPECT
MAGNIFY
VIDEO
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ASPECT
OFF
FREEZE
KEYSTONE
MAGNIFY
MENU
POSITION
 At a video signal /no signal
4:3  16:9  SMALL
RGB
ON
ON
ENTER
ESC
RESET
MUTE
OFF
FREEZE
KEYSTONE
MENU
POSITION
● The NORMAL mode keeps the original aspect ratio of the signal.
● At a HDTV signal of 1125i (1080i) or 750p (720p) of COMPONENT VIDEO
input, only 16:9 mode can be selected.
● Performing the automatic adjustment initializes the aspect ratio setting.
ENTER
ESC
Adjusting the zoom and focus
1. Use the zoom knob to adjust the screen size.
2. Use the focus ring to focus the picture.
18
Focus ring
RESET
Zoom knob
Operating
1.
Press the AUTO button on the remote control.
STANDBY/ON
VIDEO
RGB
SEARCH
HOME
PAGE UP
END
PAGE DOWN
ASPECT
STANDBY/ON
BLANK
AUTO
VIDEO
MAGNIFY
RGB
SEARCH
VOLUME
ON
MUTE
ASPECT
OFF
FREEZE
AUTO
BLANK
PAGE UP
VOLUME
KEYSTONE
MENU
POSITION
MAGNIFY
HOME
ON
 At a RGB signal
The vertical position, the horizontal position, the clock
phase and horizontal size will be automatically adjusted.
Make sure that the application window is set to its maximum size prior to
attempting to use this feature. A dark picture may still be incorrectly adjusted.
Use a bright picture when adjusting.
 At a video signal
The video format best suited for the respective input signal will be selected
automatically.
This function is available only when the AUTO mode is selected to the item
VIDEO FORMAT of the INPUT menu (30). For a component video signal,
the signal type is identified automatically independently of this function.
● The automatic adjustment operation requires approximately 10 seconds. Also
please note that it may not function correctly with some input.
ENTER
RESET
ESC
PAGE DOWN
END
MUTE
OFF
FREEZE
KEYSTONE
MENU
POSITION
ENTER
RESET
ESC
STANDBY/ON
VIDEO
RGB
MAGNIFY
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ASPECT
ON
MUTE
OFF
Adjusting the position
1.
2.
FREEZE
KEYSTONE
STANDBY/ON
VIDEO
RGB
ASPECT
SEARCH
BLANK
AUTO
Press the POSITION button on the remote control.
The “POSITION” indication will appear on the screen.
Use the cursor buttons ▲/▼/◄/► to adjust the picture
position.
When you want to reset the operation, press the RESET button on the remote
control during the operation.
To complete this operation, press the POSITION button again. Even if you don’t
do anything, the dialog will automatically disappear after a few seconds.
● When this function is performed at a video signal, a certain extra such as a line
may appear outside a picture.
MAGNIFY
HOME
PAGE UP
END
PAGE DOWN
VOLUME
ON
MUTE
MENU
POSITION
OFF
FREEZE
KEYSTONE
ENTER
MENU
POSITION
ENTER
RESET
ESC
RESET
ESC
STANDBY/ON
VIDEO
RGB
Correcting the keystone distortions
1.
MAGNIFY
STANDBY/ON
VIDEO
RGB
ASPECT
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ASPECT
ON
SEARCH
AUTO
BLANK
MUTE
Press the KEYSTONE button on the remote control.
A dialog will appear on the screen to aid you in correcting
the distortion.
Use the cursor buttons ▲/▼ to correct the distortion.
To close the dialog and complete this operation, press the KEYSTONE button
again. Even if you don’t do anything, the dialog will automatically disappear
after a few seconds.
● This function may not be work well with some input.
● The adjustable range for correcting will vary among inputs.
MAGNIFY
HOME
PAGE UP
END
PAGE DOWN
VOLUME
OFF
ON
MUTE
FREEZE
OFF
FREEZE
KEYSTONE
KEYSTONE
MENU
POSITION
ENTER
ESC
2.
RESET
MENU
POSITION
ENTER
ESC
RESET
19
ENGLISH
Using the automatic adjustment feature
Operating
STANDBY/ON
Using the magnify feature
the ON button of MAGNIFY on the remote control.
1. Press
The “MAGNIFY” indication will appear on the screen
(although the indication will disappear after several
seconds with no operation.), and the projector will enter the
MAGNIFY mode.
VIDEO
RGB
SEARCH
STANDBY/ON
VIDEO
RGB
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
ASPECT
MAGNIFY
ON
MAGNIFY
PAGE DOWN
END
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ASPECT
MUTE
OFF
ON
FREEZE
KEYSTONE
MENU
POSITION
ENTER
MUTE
OFF
FREEZE
KEYSTONE
RESET
ESC
MENU
POSITION
Use the cursor buttons ▲/▼ to adjust the zoom level.
2. To
move the zoom area, press the POSITION button in the MAGNIFY mode,
ENTER
RESET
ESC
then use the cursor buttons ▲/▼/◄/► to move the area. And to finalize the
zoom area, press the POSITION button again.
To exit the MAGNIFY mode and restore the screen to normal, press the OFF
button of MAGNIFY on the remote control.
● The projector automatically exits the MAGNIFY mode when the input signal
changes, or when an operation of changing the display condition (automatic
adjustment, etc.) is executed.
● Although in the MAGNIFY mode, the keystone distortion condition may vary, it
will be restored when the projector exit the MAGNIFY mode.
STANDBY/ON
VIDEO
RGB
Freezing the screen
1.
MAGNIFY
STANDBY/ON
VIDEO
RGB
ASPECT
SEARCH
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ASPECT
ON
BLANK
AUTO
MUTE
Press the FREEZE button on the remote control.
The “FREEZE” indication will appear on the screen, and
the projector will enter the FREEZE mode.
To exit the FREEZE mode and restore the screen to normal,
press the FREEZE button again.
● The projector automatically exits the FREEZE mode when the input signal
changes, or when one of the projector’s buttons or the remote control buttons
of STANDBY/ON, SEARCH, RGB, VIDEO, BLANK, AUTO, ASPECT, VOLUME,
MUTE, KEYSTONE, POSITION and MENU is pressed.
● If the projector continues projecting a still image for long time, the LCD panel
might possibly be printed. Do not leave the projector in FREEZE mode for too
long.
MAGNIFY
HOME
PAGE UP
END
PAGE DOWN
VOLUME
OFF
ON
MUTE
OFF
FREEZE
FREEZE
KEYSTONE
KEYSTONE
MENU
POSITION
ENTER
RESET
ESC
MENU
POSITION
ENTER
RESET
ESC
Temporarily blanking the screen
1.
STANDBY/ON
VIDEO
RGB
ASPECT
SEARCH
AUTO
BLANK
STANDBY/ON
Press the BLANK button on the remote control.
The blank screen will be displayed instead of the screen
of input signal. Please refer to the item BLANK of section
SCREEN menu (33).
To remove the blank screen and return to the input signal screen, press the
BLANK button again.
● The projector automatically returns to the input signal screen when the input
signal changes, or when one of the projector’s buttons or the remote control
buttons are pressed.
MAGNIFY
HOME
PAGE UP
END
PAGE DOWN
VOLUME
VIDEO
RGB
SEARCH
ON
MUTE
OFF
FREEZE
KEYSTONE
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ASPECT
MENU
POSITION
MAGNIFY
ENTER
ON
ESC
RESET
MUTE
OFF
FREEZE
KEYSTONE
MENU
POSITION
ENTER
ESC
20
RESET
Operating
Operating the computer screen
ENGLISH
CAUTION ►Mistaken use of the mouse/keyboard control could damage
your equipment.
• While using this function, please connect only with a computer.
• Before connecting, read the manuals of the computer you will connect.
NOTE • It may not be possible to control notebook PC, and other computers with
built-in pointing device (e.g. track ball), using this remote control. In this case, before
connecting go into BIOS (system setup) and select external mouse, and disable the
pointing device. In addition, the mouse may not function if the computer does not have
the needed utility program. See your computer’s hardware manual for details.
• The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be
possible to use the remote control, depending on the computer’s configurations and
mouse drivers.
• The USB control can be used only for the functions listed below. You cannot do things
like press two buttons at once (for instance, pressing two buttons at the same time to
move the mouse pointer diagonally).
• This function is not available while the lamp is warming up (the POWER indicator
flashes green), and while adjusting the volume and display, correcting for trapezoidal
distortion, zooming in on the screen, using the BLANK function, or displaying the menu
screen.
USB mouse and keyboard control
1. Connect the projector’s USB port to the computer via the mouse cable.
Available function
Remote control operation
Move pointer
Left click with mouse
Right click with mouse
Press keyboard’s HOME key
Press keyboard’s END key
Press keyboard’s PAGE UP key
Press keyboard’s PAGE DOWN key
Press keyboard’s ESC key
Use ▲, ▼, ◄, ► buttons
Press ENTER button
Press RESET button
Press HOME button
Press END button
Press PAGE UP button
Press PAGE DOWN button
Press ESC button
21
Multifunctional settings
Multifunctional settings
STANDBY/ON
VIDEO
RGB
ASPECT
Using the menu function
MAGNIFY
HOME
SEARCH
AUTO
BLANK
PAGE UP
VOLUME
This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP,
SCREEN, OPTION and EASY MENU. Each of these menus is operated using the
same methods. The basic operations of these menus are as follows.
ON
END
PAGE DOWN
MUTE
OFF
FREEZE
MENU button
LAMP
TEMP
MAGNIFY
Cursor buttons
INPUT
MENU
STANDBY/ON
VIDEO
SEARCH
PAGE UP
END
PAGE DOWN
AUTO
BLANK
VOLUME
ON
MUTE
OFF
FREEZE
KEYSTONE
ENTER
ENTER button
Press the MENU button on the remote control or one of the
1. cursor
buttons on the projector.
The advanced MENU or EASY MENU will appear.
Use the cursor buttons ▲/▼ to select a menu.
MENU
POSITION
ESC
RESET
RESET button
2.
RGB
HOME
ASPECT
MENU
POSITION
POWER
STANDBY/ON
KEYSTONE
ENTER
ESC
MENU [RGB]
PICTURE
IMAGE
INPUT
SETUP
SCREEN
OPTION
EASY MENU
RESET
:SELECT
BRIGHT
+0
CONTRAST
+0
GAMMA
#1 DEFAULT
COLOR TEMP
LOW
COLOR
+0
TINT
+0
SHARPNESS
+0
PROGRESSIVE TURN OFF
MY MEMORY
SAVE 1
 At the EASY MENU
Advanced MENU
If you want to change it to the advanced MENU, select the
EASY MENU
"Go to Advanced Menu".
ASPECT
4:3
 At the advanced MENU
+0
KEYSTONE
Select a menu of PICTURE, IMAGE, INPUT, SETUP,
MODE
NORMAL
BRIGHT
+0
SCREEN or OPTION.
CONTRAST
+0
+0
COLOR
If you want to change it to the EASY MENU, select the
+0
TINT
EASY MENU.
SHRPNESS
+3
NORMAL
WHISPER
Then press the cursor button ► on the projector or remote
NORMAL
MIRROR
EXECUTE
RESET
control, or the ENTER button on the remote control to
FILTER TIME
0
LANGUAGE
ENGLISH
progress.
Go To Advance Menu...
The display of the selected menu will be active.
EASY MENU
Use the cursor buttons ▲/▼ to select an item to operate.
Then press the cursor button ► on the projector or remote control, or the
ENTER button on the remote control to progress.
The operation menu of the selected item will appear.
Use the cursor buttons▲/▼ to operate the item.
When you want to reset the operation, press the RESET button on the remote
control during the operation. Note that items whose functions are performed
simultaneously with operation (ex. LANGUAGE, H PHASE etc.) aren't reset.
When you want to return to the previous display, press the cursor button ◄ on
the projector or remote control, or the ESC button on the remote control.
Press the MENU button on the remote control again to close the menu and
complete this operation.
Even if you don't do anything, the dialog will automatically disappear after about
10 seconds.
3.
4.
5.
6.
22
Multifunctional settings
EASY Menu
With the EASY MENU, items shown in the table below can
be performed.
Select an item using the cursor buttons ▲/▼ on the
projector or remote control. Then perform it referring to the
following table.
Item
ASPECT
4:3
+0
KEYSTONE
MODE
NORMAL
BRIGHT
+0
CONTRAST
+0
COLOR
+0
+0
TINT
SHRPNESS
+3
WHISPER
NORMAL
NORMAL
MIRROR
EXECUTE
RESET
FILTER TIME
0
LANGUAGE
ENGLISH
Go To Advance Menu...
Description
ASPECT
Using the buttons ◄/► switches the mode for aspect ratio.
See the item ASPECT of section IMAGE menu (28).
KEYSTONE
Using the buttons ◄/► corrects the keystone distortion.
See the item KEYSTONE of section SETUP menu (32).
Using the buttons ◄/► switches the mode of picture type.The
modes of picture type are combinations of a mode of GAMMA and
a mode of COLOR TEMP. Choose a suitable mode according to the
projected source.
NORMAL  CINEMA  DYNAMIC
MODE
NORMAL: (COLOR TEMP = MIDDLE) + (GAMMA = #1 DEFAULT)
CINEMA: (COLOR TEMP = LOW) + (GAMMA = #2 DEFAULT)
DYNAMIC: (COLOR TEMP = HIGH) + (GAMMA = #3 DEFAULT)
• When the combination of GAMMA and COLOR TEMP differs
from pre-assigned modes above, the display on the menu for the
MODE is “CUSTOM”. Please refer to the items GAMMA (25) and
COLOR TEMP (26) of PICTURE menu.
BRIGHT
Using the buttons ◄/► adjusts the brightness.
See the item BRIGHT of section PICTURE menu (25).
CONTRAST
Using the buttons ◄/► adjusts the contrast.
See the item CONTRAST of section PICTURE menu (25).
COLOR
Using the buttons ◄/► adjusts the strength of whole color.
See the item COLOR of section PICTURE menu (26).
TINT
Using the buttons ◄/► adjusts the tint.
See the item TINT of section PICTURE menu (26).
23
ENGLISH
EASY MENU
Multifunctional settings
EASY Menu (continued)
Item
SHARPNESS
WHISPER
MIRROR
Description
Using the buttons ◄/► adjusts the sharpness.
See the item SHARPNESS of section PICTURE menu (26).
Using the buttons ◄/► turns off/on the whisper mode.
See the item WHISPER of section SETUP menu (32).
Using the buttons ◄/► switches the mode for mirror status.
See the item MIRROR of section SETUP menu (32).
RESET
Performing this item resets all of the items of EASY MENU except
FILTER TIME and LANGUAGE.
A dialog is displayed to make sure. Selecting RESET using the
button ▲ performs reset.
FILTER TIME
Performing this item resets the filter timer which counts use time of
air filter.
A dialog is displayed to make sure. Selecting RESET using the
button ▲ performs reset.
See the item FILTER TIME of section OPTION menu (37).
LANGUAGE
Select the LANGUAGE to toggle the menu language. Refer to
description of LANGUAGE in the SCREEN menu (33).
Go To
Advanced Menu
24
Select the “Go To Advanced Menu” to use the menu of PICTURE,
IMAGE, INPUT, SETUP, SCREEN or OPTION.
Multifunctional settings
PICTURE Menu
Item
BRIGHT
CONTRAST
MENU [RGB]
PICTURE
IMAGE
INPUT
SETUP
SCREEN
OPTION
EASY MENU
:SELECT
+0
BRIGHT
+0
CONTRAST
GAMMA
#1 DEFAULT
COLOR TEMP
LOW
COLOR
+0
TINT
+0
SHARPNESS
+0
PROGRESSIVE TURN OFF
MY MEMORY
SAVE 1
Description
Using the buttons ▲/▼ adjusts the brightness. :
Using the buttons ▲/▼ adjusts the contrast. :
Light  Dark
Strong  Weak
Using the buttons ▲/▼ switches the GAMMA mode. :
#1 DEFAULT  #1 CUSTOM  #2 DEFAULT
#3 CUSTOM  #3 DEFAULT  #2 CUSTOM
To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM
GAMMA
Selecting a mode of CUSTOM and then
ENTER :
1 2 3 4 5 6 7
pressing the button ► or the ENTER button
displays a dialog to aid you in adjusting the
mode.
This function is useful when you want to
change the brightness of particular tones.
+0 +0 +0 +0 +0 +0 +0
GAMMA [CUSTOM 1]
Choose an item using the buttons ◄/►, and
adjust the level using the buttons ▲/▼.
You can display a test pattern for checking the effect of your
adjustment by pressing the ENTER button.
Each time you press the ENTER button, the pattern changes as
below.
No pattern  Gray scale of 9 steps
8
+0
Ramp  Gray scale of 15 steps
Eight of equalizing bars corresponds to eight of tone level of test
pattern except the darkest in the left end. If you want to adjust
the 2nd tone from left end on the test pattern, use the equalizing
adjustment bar “1”. The darkest tone at the left end of the test
pattern cannot be controlled with any of equalizing adjustment bar.
25
ENGLISH
With the PICTURE menu, items shown in the table below
can be performed.
Select an item using the cursor buttons ▲/▼ on the
projector or remote control, and press the cursor button ►
on the projector or remote control, or the ENTER button on
the remote control to progress. Then perform it referring to
the following table.
Multifunctional settings
PICTURE Menu (continued)
Item
Description
Using the buttons ▲/▼ switches the mode of color temperature.
HIGH  MIDDLE  LOW  CUSTOM
To adjust CUSTOM
COLOR TEMP
Selecting the CUSTOM and then pressing the
ENTER :
GAIN
button ► or the ENTER button displays a dialog ROFFSET
G B
R G B
to aid you in adjusting the OFFSET and/or GAIN
of CUSTOM mode.
OFFSET adjustments change the color intensity
+0 +0 +0
+0 +0 +0
on the whole tones of the test pattern.
COLOR TEMP
GAIN adjustments mainly affect color intensity
on the brighter tones of the test pattern.
Choose an item using the buttons ◄/►, and adjust the level using
the buttons ▲/▼.
You can display a test pattern for checking the effect of your
adjustment by pressing the ENTER button.
Each time you press the ENTER button, the pattern changes as
below.
No pattern  Gray scale of 9 steps
Ramp  Gray scale of 15 steps
COLOR
Using the buttons ▲/▼ adjusts the strength of whole color.
Strong  Weak
• This item can be selected only at a video signal.
TINT
Using the buttons ▲/▼ adjusts the tint.
Green  Red
• This item can be selected only at a video signal except for
SECAM.
SHARPNESS
26
Using the buttons ▲/▼ adjusts the sharpness.
Strong  Weak
Multifunctional settings
PICTURE Menu (continued)
Description
ENGLISH
Item
Using the buttons ▲/▼ switches the progressive mode.
TV  FILM  TURN OFF
PROGRESSIVE
• This function performs only at an interlaced signal of a VIDEO
input, a S-VIDEO input or a COMPONENT VIDEO input of 525i
(480i) or 625i (576i) signal.
• When the TV or FILM is selected, the screen image will be crisper.
The FILM mode is adaptable to the 2-3 Pull-Down system to the
conversion. But these may cause a certain defect (for example,
jagged line) of the picture at a quick moving object. In such a case,
please select the TURN OFF, even though the screen image may
lose the crisp.
Selecting a mode of MY MEMORY using the buttons ▲/▼ and then
pressing the button ► or the ENTER button performs each function.
LOAD1  LOAD2  LOAD3  LOAD4
MY MEMORY
SAVE4 SAVE3  SAVE2  SAVE1
This projector has 4 numbered memories for adjustment data.
Performing the LOAD1, LOAD2, LOAD3 or LOAD4 loads the data
on the memory whose number corresponds with the command’
s number, and adjusts the picture automatically depending on the
data.
Performing the SAVE1, SAVE2, SAVE3 or SAVE4 puts the current
adjustment data on the memory whose number corresponds with
the command’s number.
27
Multifunctional settings
IMAGE Menu
With the IMAGE menu, items shown in the table below can
be performed.
Select an item using the cursor buttons ▲/▼ on the
projector or remote control, and press the cursor button ►
on the projector or remote control, or the ENTER button on
the remote control to progress. Then perform it referring to
the following table.
Item
MENU [RGB]
PICTURE
IMAGE
INPUT
SETUP
SCREEN
OPTION
EASY MENU
:SELECT
ASPECT
OVER SCAN
V POSITION
H POSITION
H PHASE
H SIZE
AUTO ADJUST
4:3
95
25
142
16
1344
Description
Using the buttons ▲/▼ switches the mode for aspect ratio.
At a RGB signal
4:3  16:9  NORMAL
ASPECT
At a video signal / no signal
4:3  16:9  SMALL
• The NORMAL mode keeps the original aspect ratio of the signal.
• At a HDTV signal of 1125i (1080i) or 750p (720p) of COMPONENT
VIDEO input, this item can't be selected.
• Performing the automatic adjustment initializes the aspect ratio
setting.
OVER SCAN
Using the buttons ▲/▼ adjusts the over-scan ratio.
Large (It reduces picture)  Small (It magnifies picture)
• This item can be selected only at a video signal.
• When this adjustment is too large, certain degradation may appear
at the frame area of the picture. In such a case, please adjust small.
V POSITION
Using the buttons ▲/▼ adjusts the vertical position.
Up  Down
H POSITION
Using the buttons ▲/▼ adjusts the horizontal position.
Left  Right
H PHASE
28
Using the buttons ▲/▼ adjusts the horizontal phase to eliminate
flicker.
Right  Left
• This item can be selected only at a RGB signal or a component
video signal.
Multifunctional settings
IMAGE Menu (continued)
H SIZE
AUTO ADJUST
Description
ENGLISH
Item
Using the buttons ▲/▼ adjusts the horizontal size.
Large  Small
• This item can be selected only at a RGB signal.
• When this adjustment is excessive, the picture may not be
displayed correctly. In such a case, please reset the adjustment
pressing the RESET button on the remote control during this
operation.
Selecting this item performs the automatic adjustment feature.
At a RGB signal
The vertical position, the horizontal position, the clock phase and
horizontal size will be automatically adjusted.
Make sure that the application window is set to its maximum size
prior to attempting to use this feature. A dark picture may still be
incorrectly adjusted. Use a bright picture when adjusting.
At a video signal
The video format best suited for the respective input signal will be
selected automatically.
This function is available only when the AUTO mode is selected to
the item VIDEO FORMAT of INPUT menu. For a component video
signal, the signal type is identified automatically independently of
this function.
• The automatic adjustment operation requires approximately 10
seconds. Also please note that it may not function correctly with
some input.
29
Multifunctional settings
INPUT Menu
With the INPUT menu, items shown in the table below can
be performed.
Select an item using the cursor buttons ▲/▼ on the
projector or remote control, and press the cursor button ►
on the projector or remote control, or the ENTER button on
the remote control to progress. Then perform it referring to
the following table.
Item
MENU [RGB]
PICTURE
IMAGE
INPUT
SETUP
SCREEN
OPTION
EASY MENU
:SELECT
COLOR SPACE
COMPONENT
VIDEO FORMAT
FRAME LOCK
INFORMATION
AUTO
COMPONENT
AUTO
TURN ON
Description
Using the buttons ▲/▼ switches the mode for color space.
AUTO  RGB  SMPTE240  REC709  REC601
COLOR SPACE
• This item can be selected only at a RGB signal or a component video signal.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a
case, it might be good to select the SMPTE240 or the REC709.
COMPONENT
Using the buttons ▲/▼ switches the function of COMPONENT
VIDEO port.
COMPONENT  SCART RGB
When the SCART RGB is selected, the COMPONENT VIDEO port
function as a port for a SCART RGB signal input. A SCART adapter
and SCART cable realize a SCART RGB input to the projector. For
details, ask your dealer.
VIDEO FORMAT
Using the buttons ▲/▼ switches the mode for video format.
AUTO  NTSC  PAL  SECAM
N-PAL  M-PAL  NTSC4.43
• This item performs only at a video signal from the VIDEO port or
the S-VIDEO port. For a component video signal, the signal type is
identified automatically independently of this function.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. If the
picture becomes unstable (ex. an irregular picture, a color lack),
please select the mode depending on the input signal.
FRAME LOCK
Using the buttons ▲/▼ turns the frame lock function on/off.
TURN ON  TURN OFF
• This item performs only at a RGB signal with vertical frequency of
50 to 60 Hz for the models 8755C, or 50 to 72Hz
for the model 8063.
• When the TURN ON is selected, a moving picture is displayed
more smoothly.
• This function may cause a certain degradation of the picture. In
such a case, please select the TURN OFF.
30
Multifunctional settings
Item
Description
Selecting this item displays a dialog titled “INPUT INFORMATION”.
It shows the information about the current input.
INPUT-INFORMATION
RGB
1024x768 @60.0
FRAME LOCK
INFORMATION
INPUT-INFORMATION
S-VIDEO
SECAM
AUTO
INPUT-INFORMATION
COMPONENT
576i @50
SCART RGB
• The “FRAME LOCK” message on the dialog means the frame lock
function is working (30).
• The “SCART RGB” message means the COMPONENT VIDEO
port is working as a SCART RGB input port. Please refer to the item
COMPONENT in this section. (30)
• This item is can't be selected at no signal.
31
ENGLISH
INPUT Menu (continued)
Multifunctional settings
SETUP Menu
With the SETUP menu, items shown in the table below can
be performed.
Select an item using the cursor buttons ▲/▼ on the
projector or remote control, and press the cursor button ►
on the projector or remote control, or the ENTER button on
the remote control to progress. Then perform it referring to
the following table.
MENU [RGB]
PICTURE
IMAGE
INPUT
SETUP
SCREEN
OPTION
EASY MENU
:SELECT
KEYSTONE
WHISPER
MIRROR
VOLUME
Item
Description
KEYSTONE
Using the buttons ▲/▼ corrects the keystone distortion.
Upper in the data  Lower in the data
• The adjustable range of this function will vary with the type of input
signal. At some signals, this function may not work well.
• When the V:INVERT or the H&V:INVERT is selected under the
item MIRROR, if the projector screen is inclined or if the projector is
angled downward, this function may not work correctly.
• When the zoom adjustment is set to the TELE side, this correction
may be excessive. This function should be used with zoom set to
WIDE whenever possible.
WHISPER
Using the buttons ▲/▼ turns off/on the whisper mode.
NORMAL  WHISPER
• When the WHISPER is selected, acoustic noise and screen
brightness are reduced.
Using the buttons ▲/▼ switches the mode for mirror status.
MIRROR
NORMAL  H:INVERT  V:INVERT  H&V:INVERT
VOLUME
32
+0
NORMAL
NORMAL
16
Using the buttons ▲/▼ adjusts the volume.
High  Low
Multifunctional settings
SCREEN Menu
Item
MENU [RGB]
PICTURE
IMAGE
INPUT
SETUP
SCREEN
OPTION
EASY MENU
:SELECT
LANGUAGE
MENU POSITION
OSD BRIGHT
BLANK
START UP
MyScreen
MyScreen Lock
MESSAGE
ENGLISH
5
BLACK
ORIGINAL
TURN OFF
TURN ON
Description
Using the buttons ▲/▼ switches the OSD (On Screen Display)
language.
LANGUAGE
ENGLISH  FRANÇAIS  DEUTSCH  ESPAÑOL  ITALIANO
NORSK  NEDERLANDS  PORTUGUÊS 
 SVENSKA 

 SUOMI  POLSKI
MENU POSITION
Using the buttons ◄/►/▲/▼ adjusts the menu position.
To quit the operation, press the MENU button on the remote control
or keep no operation for 10 seconds.
OSD BRIGHT
Using the buttons ▲/▼ switches the brightness level of the OSD (On
Screen Display).
Bright  Dark
Using the buttons ▲/▼ switches the mode the blank screen.
The blank screen is the screen for the temporarily blanking feature
(20). It is displayed by pressing the BLANK button on the remote
control.
MyScreen  ORIGINAL  BLUE  WHITE  BLACK
BLANK
MyScreen is the screen you can register a desired screen.
ORIGINAL screen is the existing standard screen. BLUE, WHITE
and BLACK are non-patterned (plain) screens in each color.
• To avoid remaining as an afterimage, the MyScreen and the
ORIGINAL screens will change to the BLACK screen after several
minutes.
• For the MyScreen, please refer to the item MyScreen (34).
33
ENGLISH
With the SCREEN menu, items shown in the table below can
be performed.
Select an item using the cursor buttons ▲/▼ on the
projector or remote control, and press the cursor button ►
on the projector or remote control, or the ENTER button on
the remote control to progress. Then perform it referring to
the following table.
Multifunctional settings
SCREEN Menu (continued)
Item
Description
Using the buttons ▲/▼ switches the mode the start up screen.
The start up screen is the screen displayed when no signal or an
unsuitable signal is detected.
MyScreen  ORIGINAL  TURN OFF
START UP
My Screen
My Screen Lock
34
MyScreen is the screen you can register a desired screen.
ORIGINAL screen is the existing standard screen. When the TURN
OFF is selected, the BLUE screen is used.
• To avoid remaining as an afterimage, the MyScreen and the
ORIGINAL screens will change to the BLANK screen after several
minutes. If also the BLANK screen is the MyScreen or ORIGINAL, it
will change to the BLACK screen.
• For the MyScreen, please refer to the item MyScreen below.
About the BLUE, BLACK and BLANK screens, please refer to the
item BLANK (33).
This item functions for capturing the MyScreen of the blank screen
and the start up screen. Please execute displaying the input
including the picture you want to capture.
1. Selecting this item displays a dialog titled “MyScreen”. It will ask
you if you start capturing the picture from the current screen.
Please wait for the target picture to be displayed, and press the
ENTER button on the remote control when the picture is display.
The picture will freeze and the frame for capturing appears.
To stop performing, press the RESET or ESC button on the
remote control.
2. Using the buttons ◄/►/▲/▼ adjust the frame position. Please
move the frame to the position of the picture which you want to
use.
To start registration, press the ENTER button on the remote
control.
To restore the screen and return to the previous dialog, press the
RESET or ESC button on the remote control.
Registration takes several minutes. When the registration is
completed, the registered screen and the message “MyScreen
registration is finished.” are displayed for several seconds. If the
registration failed, the message “A capturing error has occurred.
Please try again.” is displayed.
Using the buttons ▲/▼ turns on/off the MyScreen lock function.
TURN ON  TURN OFF
When the TURN ON is selected, the item MyScreen cannot be
performed. Use this function for protecting the current MyScreen.
Multifunctional settings
SCREEN Menu (continued)
MESSAGE
Description
ENGLISH
Item
Using the buttons ▲/▼ turns on/off the message function.
TURN ON  TURN OFF
When the TURN ON is selected, the following message function
works.
“AUTO IN PROGRESS” while automatically adjusting
”NO INPUT IS DETECTED”
”SYNC IS OUT OF RANGE”
”Searching ....” while searching for an input signal
”Detecting….” when an input signal is detected
The indication of the input signal by changing
The indication of the aspect ration by changing .
35
Multifunctional settings
OPTION Menu
With the OPTION menu, items shown in the table below can
be performed.
Select an item using the cursor buttons ▲/▼ on the projector
or remote control, and press the cursor button ► on the
projector or remote control, or the ENTER button on the
remote control to progress, except for the items LAMP TIME
and FILTER TIME. Then perform it referring to the following
table.
Item
SEARCH
MENU [RGB]
PICTURE
IMAGE
INPUT
SETUP
SCREEN
OPTION
EASY MENU
:SELECT
SEARCH
AUTO OFF
LAMP TIME
FILTER TIME
SERVICE
TURN ON
0
0
0
Description
Using the buttons ▲/▼ turns on/off the message function.
TURN ON  TURN OFF
When the TURN ON is selected, detecting no signal automatically
cycles through input ports in order of following. Then when an input
is found, the projector will stop searching and display the image.
If no signal is found, the projector will return to the state before the
operation.
RGB IN1  RGB IN2  COMPONENT VIDEO  S-VIDEO  VIDEO
Using the buttons ▲/▼ adjusts the time to count down to
automatically turn the projector off.
Long (max. 99 minutes)  Short (min. 0 minute = DISABLE)
AUTO OFF
LAMP TIME
36
AUTO OFF
ENABLE
AUTO OFF
DISABLE
1
0
When the time is set to 0, the projector is not turned off
automatically.
When the time is set to 1 to 99, and when the passed time with
a no-signal or an unsuitable signal reaches at the set time, the
projector lamp will go off and the power indicator begins blinking.
Please refer to the section “Turning off the power” (16).
The lamp time is the time counted after the last resetting. It is
shown in the OPTION menu as the use time of the lamp.
Pressing the RESET button on the remote control for about 3
seconds displays a dialog. To reset the lamp time, select the
RESET using the button ▲.
RESET  CANCEL
• Please reset the lamp time only when you have replaced the lamp,
for correct messages about the lamp.
• About the lamp replacement, please see the section "Lamp" (
38, 39).
Multifunctional settings
Item
Description
FILTER TIME
The filter time is the time counted after the last resetting. It is shown
in the OPTION menu as the use time of the air filter.
Pressing the RESET button on the remote control for about 3
seconds displays a dialog. To reset the filter time, select the RESET
using the button ▲.
RESET  CANCEL
• Please reset the filter time only when you have cleaned or
replaced the air filter, for correct messages about the air filter.
• About the caring the air filter, please see the section "Air filter" (
40).
Selecting this item displays the SERVICE menu.
Select an item using the buttons ▲/▼, and press the button ► or
the ENTER button on the remote control to progress.
FAN SPEED  FACTORY RESET  GHOST
SERVICE
FAN SPEED
Using the buttons ▲/▼ switches the rotation speed of the cooling
fans. The HIGH is the mode for use at highlands etc. Note that the
projector is noisier when the HIGH is selected.
HIGH  NORMAL
GHOST
1. Select a color element of ghost using the buttons ▲/▼ and press
the cursor button ► or the ENTER button on the remote control
to progress.
2. Adjust the selected element using the buttons ▲/▼ to disappear
ghost.
FACTORY RESET
Selecting RESET using the button ▲ performs this function. By this
function, all the items in all of menu will collectively return to the
initial setting. Note that the items LAMP TIME, FILTER TIME and
LANGUAGE are not reset.
RESET  CANCEL
37
ENGLISH
OPTION Menu (continued)
Maintenance
Maintenance
Lamp
WARNING
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
►The projector uses a high-pressure mercury glass lamp. The lamp can break
with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn
over time. Note that each lamp has a different lifetime, and some may burst or
burn out soon after you start using them. In addition, when the bulb bursts, it is
possible for shards of glass to fly into the lamp housing, and for gas containing
mercury to escape from the projector’s vent holes.
►About disposal of a lamp • This product contains a mercury lamp; do not
put in trash. Dispose of in accord with environmental laws.
For lamp recycling, go to www.lamprecycle.org. (in the US)
For product disposal, contact your local government agency or www.eiae.org (in
the US) or www.epsc.ca (in Canada).
For more information, call your dealer.
• If the lamp should break (it will make a loud bang when it does),
unplug the power cord from the outlet, and make sure to request a
replacement lamp from your local dealer. Note that shards of glass
could damage the projector’s internals, or cause injury during handling,
so please do not try to clean the projector or replace the lamp yourself.
Disconnect • If the lamp should break (it will make a loud bang when it does),
the plug ventilate the room well, and make sure not to breathe the gas that
from the comes out of the projector vents, or get it in your eyes or mouth.
power
• Before replacing the lamp, turn the projector off and unplug the power
outlet
cord, then wait at least 45 minutes for the lamp to cool sufficiently.
Handling the lamp while hot can cause burns, as well as damaging the
lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from
above. This is dangerous, since if the lamp’s bulb has broken, the
shards will fall out when the cover is opened. In addition, working in
high places is dangerous, so ask your local dealer to have the lamp
replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose
screws could result in damage or injury.
• Use only the lamp of the specified type.
• If the lamp breaks soon after the first time it is used, it is possible
that there are electrical problems elsewhere besides the lamp. If this
happens, contact your local dealer or a service representative.
• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• If the indicators or a message prompts you to replace the lamp (see
the section "Related Messages" and "Regarding the indicator Lamps"),
replace the lamp as soon as possible. Using the lamp for long periods
of time, or past the replacement date, could cause it to burst. Do not
use old (used) lamps; this is a cause of breakage.
38
Lamp (continued)
When the indicators or a message prompts you to replace the lamp, replace the
lamp as soon as possible.
Turn the projector off, and unplug the power cord. Allow the lamp to cool for
at least 45 minutes.
To prepare a new lamp, contact your dealer and tell the lamp type number
= 456-8063. If the projector is mounted on the ceiling, or if the lamp has
broken, also ask the dealer to replace the lamp.
Lamp cover
1.
2.
In the case of replacement by yourself,
After making sure that the projector has
cooled adequately, slowly turn over the
projector, so that the bottom is facing up.
Please unhook the claws of the lamp cover
using a minus screwdriver or similar, and
remove the lamp cover.
Loosen the 2 screws (marked by arrow) of
the lamp, and slowly pick up the lamp by the
handles.
Insert the new lamp, and retighten firmly two
screws that are loosened in the previous
process to lock it in place.
Interlocking the 2 tabs of the lamp cover to
the projector, position the lamp cover on the
projector. Then push the center point of two
claws to fix the lamp cover.
Slowly turn the projector so that the top is
facing up.
Turn the projector on, and reset the lamp time
using the LAMP TIME function of OPTION
menu (36).
3.
4.
Claws
Screws marked
by arrow
5.
6.
7.
8.
9.
Tabs
Center point
of claws
Claws
NOTE • When the lamp has been replaced after the message of "THE
POWER WILL TURN OFF AFTER 0hr." is displayed, complete the following
operation within 10 minutes of switching power on.
• Incorrectly resetting of the lamp timer (resetting without replacement, or
neglect of resetting after replacement) will result in incorrect message functions.
39
ENGLISH
Maintenance
Maintenance
Air filter
WARNING ►Before caring, make sure the power switch is off and the
power cable is not plugged in, then allow the projector to cool sufficiently. The
care in a high temperature state of the projector could cause a burn and/or
malfunction to the projector.
►Use only the air filter of the specified type. Do not use the projector with the
air filter and filter cover removed.
►Avoid wetting the projector or inserting liquids in the projector. It could result
in a fire, an electric shock, and and/or malfunction to the projector.
CAUTION ►Please replace the air filter when it is damaged or too soiled,
and also when you replace the lamp.
When the indicators or a message prompts you to clean the air filter, clean the air filter as
soon as possible. If the air filter becomes clogged by dust or the like, internal temperatures
rise and the power may be automatically turned off for malfunction prevention.
Turn the projector off, and unplug the power cord.
Filter cover’s knob
Allow the projector to cool for at least 45 minutes. And
prepare a vacuum cleaner.
After making sure that the projector is cool adequately,
slowly turn the projector so that the lens-side is facing
up. Please be careful for a projector not to fall. While the
projector is placed lens-side up, hold the projector.
Putting a finger on the filter cover’s knob, slide the
Filter cover
filter cover in the direction of the arrow to remove it.
Air filter’s knob
Holding the air filter’s knob, pull the air filter off.
1.
2.
3.
4.
a vacuum cleaner to the vent of the projector for the
5. Apply
air filter. And then slowly turn the projector bottom up.
a vacuum cleaner to the air filter and filter cover.
6. Apply
Please replace the air filter when it is damaged or too soiled.
To prepare a new air filter, contact your dealer and tell the air Air filter
filter type number = NJ09702.
An air filter of specified type will come even with the replacement lamp for this projector.
Position the cleaned air filter or a new air filter into place, and push the points
of "PUSH" word with claws to fix the air filter.
Replace the filter cover and snap it back into place.
7.
8.
9. Slowly turn the projector so that the top is facing up.
the projector on, and reset the filter time using the FILTER TIME
10. Turn
function of OPTION menu (37).
NOTE • Incorrectly resetting of the filter timer (resetting without replacement,
or neglect of resetting after replacement) will result in incorrect message
functions.
40
Maintenance
WARNING ►Before caring, make sure the power switch is off and the
power cable is not plugged in, and then allow the projector to cool sufficiently.
The care in a high temperature state of the projector could cause a burn and/or
malfunction to the projector.
►Never try to care for the inside of the projector personally. Doing is so
dangerous.
►Avoid wetting the projector or inserting liquids in the projector. It could result
in a fire, an electric shock, and and/or malfunction to the projector.
• Don’t put a container containing water, cleaner or chemicals near the
projector.
• Don’t use aerosols or sprays.
CAUTION ►Please take right care of the projector according to the
following. Incorrect care could cause not only an injury but adverse influence
such as discoloration, peeling paint, etc.
• Do not use cleaner or chemicals other than those listed below.
• Do not polish or wipe with hard objects.
Inside of the projector
In order to ensure the safe use of your projector, please have it cleaned and
inspected by your dealer about once every 2 years.
Caring for the lens
If the lens is flawed, soiled or fogged, it could cause deterioration of display
quality. Please take care of the lens, being cautious of the handling.
Turn the projector off, and unplug the power cord. Allow the projector to cool
sufficiently.
After making sure that the projector is cool adequately, lightly wipe the lens
with a commercially available lens-cleaning wipe. Do not touch the lens
directly with your hand.
1.
2.
Caring for the cabinet and remote control
Incorrect care could have adverse influence such as discoloration, peeling paint,
etc.
Turn the projector off, and unplug the power cord. Allow the projector to cool
sufficiently.
After making sure that the projector is cool adequately, lightly wipe with gauze
or a soft cloth.
If soiling is severe, dip soft cloth in water or a neutral cleaner dilute in water,
and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.
1.
2.
41
ENGLISH
Other care
Troubleshooting
Troubleshooting
Related messages
When the unit's power is on, messages such as those shown below may be
displayed. When any such message is displayed on the screen, please respond
as described below. If the same message is displayed after the treatment, or if a
message other than the following appears, please contact your dealer or service
company.
Although these messages will be automatically disappeared around several
minutes, it will be reappeared every time the power is turned on.
Message
Description
CHANGE THE LAMP
The time the lamp timer has counted is approaching
2000 hours.
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
Preparation of a new lamp, and an early lamp change is
recommended. After you have change the lamp, please be
sure to reset the lamp timer (36).
The time the lamp timer has counted is approaching
2000 hours, so a lamp change within ** hours is
recommended.
When lamp usage reaches 2000 hours, the power will
automatically be turned off. Please change the lamp by
THE POWER WILL TURN OFF referring to the section “Lamp”. After you have changed the
AFTER ** hr.
lamp, please be sure to reset the lamp timer (36).
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
As the time the lamp timer has counted has reached
2000 hours, the power will soon be automatically
turned off.
Please immediately turn the power off, and change the lamp
THE POWER WILL TURN OFF by referring to the section “Lamp”. After changing the lamp,
please be sure to reset the lamp timer (36).
AFTER 0 hr.
NO INPUT IS DETECTED
ON ***
SYNC IS OUT OF RANGE
ON *** fH *****kHz fV *****Hz
There is no input signal.
Please confirm the signal input connection, and the status
of the signal source.
The horizontal or vertical wavelength of the inputted
signal is outside of the response parameters of this unit.
Please confirm the specs for this unit or the signal source specs.
The internal portion temperature is rising.
CHECK THE AIR FLOW
42
Please turn the power OFF, and allow the unit to cool down at least 20 minutes.
After having confirmed the following items, please turn the power ON again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
• If the same indication is displayed after the treatment, please set the
HIGH at the FAN SPEED of the item SERVICE of the OPTION menu.
Troubleshooting
Related messages (continued)
Description
A note of precaution when cleaning the air filter.
Please immediately turn the power OFF, and clean or
change the air filter by referring to the “Air Filter” section of
this manual. After you have cleaned or changed the air filter,
please be sure to reset the filter timer (37).
NOTE • A lamp has a finite product life. Lamps are characterized by the
fact that, after long hours of usage, a lamp will no longer light up, or the lamp
will break or burst, etc. This projector is equipped with an automatic shut-down
function, such that the power will automatically be turned off when lamp usage
time has reached 2000 hours. Please be aware, however, that among lamp
types, there are major differences in product lifetimes; a lamp may thus fail to
light even prior to the functioning of the automatic shut-down function of this
projector.
43
ENGLISH
Message
CLEAN THE AIR FILTER
POWER OFF FIRST,
THEN CLEAN THE AIR
FILTER.
AFTER CLEANING THE AIR
FILTER,
RESET THE FILTER TIMER.
Troubleshooting
Regarding the indicator lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP
indicator have the meanings as described in the table below. Please respond
in accordance with the instructions within the table. If the same indication is
displayed after the treatment, or if an indication other than the following is
displayed, please contact your dealer or service company.
LAMP
TEMP
POWER
Description
indicator indicator indicator
Turned The projector is in a standby state.
Lighting
Turned
In Orange
off
off
Please refer to the section “Power On/Off”.
Blinking
In Green
Turned
off
Turned
off
The projector is warming up.
Lighting
In Green
Turned
off
Turned
off
The projector is in an on state.
Blinking
In Orange
Turned
off
Turned
off
The projector is cooling down.
Blinking
In Red
(discretionary)
(discretionary)
Please wait.
Ordinary operations may be performed.
Please wait.
The projector is cooling down. A certain error
has been detected.
Please wait until the POWER indicator finishes blink,
and then perform the proper response measure using
the item descriptions below as reference.
The lamp does not light, and there is a
possibility that interior portion has become
heated.
Blinking
In Red
or
Lighting
In Red
Lighting
In Red
Turned
off
Please turn the power off, and allow the unit to cool
down at least 20 minutes. After the projector has
sufficiently cooled down, please make confirmation of
the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the treatment,
please change the lamp by referring to the section
“Lamp”.
The lamp cover has not been properly fixed
(attached).
Blinking
In Red
or
Lighting
In Red
44
Blinking
In Red
Turned
off
Please turn the power off, and allow the unit to cool
down at least 45 minutes. After the projector has
sufficiently cooled down, please make confirmation
of the attachment state of the lamp cover. After
performing any needed maintenance, turn the power
on again. If the same indication is displayed after
the treatment, please contact your dealer or service
company.
Troubleshooting
LAMP
TEMP
POWER
indicator indicator indicator
Description
The cooling fan is not operating.
Blinking
In Red
or
Lighting
In Red
Turned
off
Blinking
In Red
Please turn the power off, and allow the unit to cool
down at least 20 minutes. After the projector has
sufficiently cooled down, please make confirmation
that no foreign matter has become caught in the fan,
etc., and then turn the power on again.
If the same indication is displayed after the treatment,
please contact your dealer or service company.
There is a possibility that the interior portion
has become heated.
Blinking
In Red
or
Lighting
In Red
Lighting
In Green
Turned
off
Lighting
In Red
Alternative
blinking in Red
Please turn the power off, and allow the unit to cool
down at least 20 minutes. After the projector has
sufficiently cooled down, please make confirmation of
the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the treatment,
please set the HIGH at the FAN SPEED of the item
SERVICE of the OPTION menu.
There is a possibility that the interior portion
has become overcooled.
Please use the unit within the usage temperature
parameters (5°C to 35°C). After the treatment, resent
the power to ON.
It is time to clean the air filter.
Lighting
In Green
Simultaneous
blinking in Red
Please immediately turn the power OFF, and clean
or change the air filter by referring to the section “Air
Filter”. After cleaning or changed the air filter, please
be sure to reset the filter timer. After the treatment,
resent the power to ON.
NOTE • When the interior portion has become overheated, for safety
purposes, the power source is automatically turned off, and the indicator lamps
may also be turned off. In such a case, press the “” (OFF) side of the power
switch, and wait at least 45 minutes. After the projector has sufficiently cooled
down, please make confirmation of the attachment state of the lamp and lamp
cover, and then turn the power on again.
45
ENGLISH
Regarding the indicator lamps (continued)
Troubleshooting
Phenomena that may easily be mistaken for machine defects
WARNING ►Never use the projector if abnormal operations such as
smoke, strange odor, excessive sound, damaged casing or elements or cables,
penetration of liquids or foreign matter, etc. should occur. In such cases,
immediately turn off the power switch and then disconnect the power plug from
the power outlet After making sure that the smoke or odor has stopped, contact
your dealer or service company.
requesting repair, please check in accordance with the following chart.
1. Before
This operation sometimes resolves your problem.
If the situation cannot be corrected,
projector’s microprocessor may need to be reset. Please push the
2. The
Restart switch by using a cocktail stick or similar and the projector will restart.
Some setting may be wrong. Please use the FACTORY RESET function of
3. SERVICE
menu in the OPTION menu (37) to reset all settings to factory
default.
Then, if the problem is not removed after maintenance, please contact your dealer
or service company.
Phenomenon
Cases not involving a machine defect
The electrical power cord is not plugged in.
13
The power switch is not set to the on position.
16
Correctly connect the power cord.
Set the power switch to [ | ] (On).
The main power source has been interrupted during
operation such as by a power outage (blackout), etc.
Power does not
come on.
Reference
page
Please turn the power off, and allow the unit to cool down at
least 20 minutes. After the projector has sufficiently cooled
down, please turn the power on again.
16
Either there is no lamp and/or lamp cover, or either
of these has not been properly fixed.
Please turn the power off, and allow the unit to cool down at
least 45 minutes. After the projector has sufficiently cooled
down, please make confirmation of the attachment state of
the lamp and lamp cover, and then turn the power on again.
46
38, 39
Troubleshooting
Phenomenon
Cases not involving a machine defect
The lens cover is closed.
Remove the lens cover.
The signal cables are not correctly connected.
Correctly connect the connection cables.
No pictures are
displayed.
The brightness is adjusted to an extremely low level.
Adjust the BRIGHT to a higher level using the menu function
or the remote control.
The computer cannot detect the projector as a plug
and play monitor.
Make sure that the computer’s can detect a plug and play
monitor using other plug and play monitor.
Colors have a
faded- out
appearance, or
Color tone is
poor.
Color settings are not correctly adjusted.
Perform picture adjustments by changing the COLOR
TEMP, COLOR, TINT and/or COLOR SPACE settings,
using the menu functions.
COLOR SPACE setting is not suitable.
Change the COLOR SPACE setting to AUTO, RGB,
SMPTE240 , REC709 or REC601.
The brightness and/or contrast are adjusted to an
extremely low level.
Adjust the BRIGHT and/or CONTRAST settings to a higher
level using the menu function.
Pictures appear
dark.
The WHISPER function is working.
Select the NORMAL to the item WHISPER in the SETUP
menu.
4, 16
10
23, 25
10
23, 25,
30
30
24, 25
24, 32
The lamp is approaching the end of its product
lifetime.
38, 39
Either the focus and/or horizontal phase settings are
not properly.
18, 28
Replace the lamp.
Pictures appear
blurry.
Reference
page
Adjust the focus using the focus ring, and/or H PHASE
using the menu function.
The lens is dirty or misty.
Clean the lens by referring to the section “Caring for the
lens”.
41
NOTE • Although bright spots or dark spots may appear on the screen, this
is a unique characteristic of liquid crystal displays, and such do not constitute or
imply a machine defect.
47
ENGLISH
Phenomena that may easily be mistaken for machine defects (continued)
Warranty And After-Service
Warranty and after-service
If a problem occurs with the equipment, first refer to the “Troubleshooting” and
run through the suggested checks. If this does not resolve the problem, please
contact your dealer or the service company. They will tell you what warranty
condition is applied.
Specifications
Specifications
NOTE • This specifications are subject to change without notice.
Item
Product name
Liquid
Crystal
panel
Specification
Liquid crystal projector
Panel size
1.8 cm (0.7 type)
Drive system
TFT active matrix
Pixels
Pixels
8063
CP-S335:
480,000 pixels (800 horizontal x 600 vertical)
CP-X340:
8755C 786,432 pixels (1024 horizontal x 768 vertical)
Lens
Zoom lens F=1.7 ~ 1.9 f=21.8 ~ 26.2 mm
Lamp
165W UHB
Power Supply
AC100-120V/2.7A, AC220-240V/1.5A
Power Consumption
240W
Temperature range
5 ~ 35°C (Operating)
Size
297 (W) x 64 (H) x 233 (D) mm
(Not including protruding parts)
• Please refer to the following figure.
Weight (mass)
Ports
Optional
parts
48
2.5 kg
RGB input:
RGB IN1 ..D-sub 15pin mini x1
RGB IN2 ..D-sub 15pin mini x1
RGB output:
RGB OUT D-sub 15pin mini x1
Communication port:
CONTROL ............ D-sub 9pin x1
USB ....................... USB(B) x1
Lamp
456-8063
Air filter
NJ09702
Others
• Please consult your dealer.
Video input:
COMPONENT VIDEO
Y ............................... RCA x1
CB/PB ....................... RCA x 1
CR/PR ...................... RCA x 1
S-Video ................................ 1
Video .................................... 1
Audio input:
AUDIO IN1 ...... Stereo mini x1
AUDIO IN2 ...... Stereo mini x1
Audio output:
AUDIO OUT ... Stereo mini x1
Specifications
232.8
79.7
32.2
84.5
65.4
64.2
80.0
297.0
14.3
237.4
ENGLISH
Specifications (continued)
[unit: mm]
49
Projector
8063/8755C
User's Manual – Operating Guide
Technical
Resolution (H x V) H. frequency (kHz) V. frequency (Hz)
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
1280 x 1024
1280 x 1024
1600 x 1200
37.9
31.5
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
48.4
56.5
60.0
68.7
67.5
60.0
64.0
80.0
91.2
75.0
85.0
59.9
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.5
60.0
70.1
75.0
85.0
75.0
60.0
60.0
75.0
85.0
60.0
Rating
Signal mode
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
TEXT
VGA (60Hz)
VGA (72Hz)
VGA (75Hz)
VGA (75Hz)
SVGA (56Hz)
SVGA (60Hz)
SVGA (72Hz)
SVGA (75Hz)
SVGA (85Hz)
Mac 16” mode
XGA (60Hz)
XGA (70Hz)
XGA (75Hz)
XGA (75Hz)
SXGA (75Hz)
SXGA (60Hz)
SXGA (60Hz)
SXGA (75Hz)
SXGA (85Hz)
UXGA (60Hz)
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
NOTE • Be sure to check jack type, signal level, timing and resolution
before connecting this projector to a computer.
• Some computers may have multiple display screen modes. Use of some of
these modes will not be possible with this projector.
• Depending on the input signal, full-size display may not be possible in some
cases. Refer to the number of display pixels above.
• Although the projector can display signals with resolution up to UXGA
(1600x1200), the signal will be converted to the projector’s panel resolution
before being displayed. The best display performance will be achieved if the
resolutions of the input signal and projector panel are identical.
• Automatically adjustment may not function correctly with some input signals.
• The image may not be displayed correctly when the input sync signal is a
composite sync or a sync on G.
1
TECHNICAL
Example of computer signal
Example of computer signal
Initial set signals
The following signals are used for the initial settings. The signal timing of some
computer models may be different. In such case, adjust the items V POSITION
and H POSITION in the IMAGE menu.
Back porch (B)
Front porch (D)
Back porch (b)
Display interval (C)
Data
H. Sync.
Display interval (c)
Data
V. Sync.
Sync (A)
Computer/ Horizontal signal timing (μs)
Signal
(A)
(B)
(C)
(D)
TEXT
2.0
3.0 20.3 1.0
VGA (60Hz)
3.8
1.9 25.4 0.6
VGA (72Hz)
1.3
3.8 20.3 1.0
VGA (75Hz)
2.0
3.8 20.3 0.5
VGA (85Hz)
1.6
2.2 17.8 1.6
SVGA (56Hz) 2.0
3.6 22.2 0.7
SVGA (60Hz) 3.2
2.2 20.0 1.0
SVGA (72Hz) 2.4
1.3 16.0 1.1
SVGA (75Hz) 1.6
3.2 16.2 0.3
SVGA (85Hz) 1.1
2.7 14.2 0.6
Mac 16" mode 1.1
3.9 14.5 0.6
XGA (60Hz)
2.1
2.5 15.8 0.4
XGA (70Hz)
1.8
1.9 13.7 0.3
XGA (75Hz)
1.2
2.2 13.0 0.2
XGA (85Hz)
1.0
2.2 10.8 0.5
1152 x 864
1.2
2.4 10.7 0.6
(75Hz)
1280 x 960
1.0
2.9
11.9
0.9
(60Hz)
1280 x 1024
1.0
2.3
11.9
0.4
(60Hz)
1280 x 1024
1.1
1.8
9.5
0.2
(75Hz)
1280 x 1024
1.0
1.4
8.1
0.4
(85Hz)
1600 x 1200
1.2
1.9
9.9
0.4
(60Hz)
2
Front porch (d)
Sync (a)
Computer/ Vertical signal timing (lines)
Signal
(a)
(b)
(c)
(d)
TEXT
3
42
400
1
VGA (60Hz)
2
33
480
10
VGA (72Hz)
3
28
480
9
VGA (75Hz)
3
16
480
1
VGA (85Hz)
3
25
480
1
SVGA (56Hz)
2
22
600
1
SVGA (60Hz)
4
23
600
1
SVGA (72Hz)
6
23
600
37
SVGA (75Hz)
3
21
600
1
SVGA (85Hz)
3
27
600
1
Mac 16" mode
3
39
624
1
XGA (60Hz)
6
29
768
3
XGA (70Hz)
6
29
768
3
XGA (75Hz)
3
28
768
1
XGA (85Hz)
3
36
768
1
1152 x 864
3
32
864
1
(75Hz)
1280 x 960
3
36
960
1
(60Hz)
1280 x 1024
3
38 1024
1
(60Hz)
1280 x 1024
3
37 1024
2
(75Hz)
1280 x 1024
3
44 1024
1
(85Hz)
1600 x 1200
3
46 1200
1
(60Hz)
Connection to the ports
Connection to the ports
AUDIO IN1
Y
AUDIO OUT
CB/PB
VIDEO
AUDIO IN2
CR/PR S-VIDEO
COMPONENT VIDEO
E
F
RGB IN1
D
RGB IN2
A
RGB OUT
B
C
USB
CONTROL
A RGB IN 1, B RGB IN 2, C RGB OUT
D-sub 15pin mini shrink jack
11 12 13 14 15
7
1
8
2
9
3
10
4
5
• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive)
• H/V. sync. Signal: TTL level (positive/negative)
• Composite sync. Signal: TTL level
At RGB signal
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
At component video signal
Pin
1
2
3
4
5
6
7
8
9
10
11
Signal
Video Red
CR/PR
Video Green
Y
Video Blue
CB/PB
(No connection)
(No connection)
Ground
Ground
Ground Red
CR/PR Ground
Ground Green
Y Ground
Ground Blue
CB/PB Ground
(No connection)
(No connection)
Ground
Ground
(No connection)
A : SDA (DDC data), B / C : (No connection)
(No connection)
15
H. sync / Composite sync.
V. sync.
* except for RGB OUT.
A : SCL (DDC clock), B / C : (No connection)
D AUDIO IN1, E AUDIO IN2, F AUDIO OUT
φ3.5 stereo mini jack
• Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminator (positive)
• H/V. sync. Signal: TTL level (positive/negative)
• Composite sync. Signal: TTL level
3
TECHNICAL
6
Connection to the ports
Connection to the ports
AUDIO IN1
Y
J
G
AUDIO OUT
RGB IN1
RGB IN2
RGB OUT
CB/PB
H
VIDEO
CR/PR S-VIDEO
COMPONENT VIDEO
I
AUDIO IN2
K
USB
CONTROL
COMPONENT VIDEO G Y, H CB/PB, I CR/PR
RCA jack x3
• System: 525i(480i), 525p(480p), 625i(576i), 750p(720p), 1125i(1080i)
Port
Signal
Y
Component video Y, 1.0±0.1Vp-p, 75Ω terminator with composite
CB/PB Component video CB/PB, 0.7±0.1Vp-p, 75Ω terminator
CR/PR Component video CR/PR, 0.7±0.1Vp-p, 75Ω terminator
J S-VIDEO
Mini DIN 4pin jack
1
3
2
4
Pin
1
2
3
4
Signal
Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator
Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator
Brightness signal, 1.0Vp-p, 75Ω terminator
Ground
Ground
K VIDEO
RCA jack
• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL60
• 1.0±0.1Vp-p, 75Ω terminator
4
Connection to the ports
AUDIO IN1
Y
AUDIO OUT
RGB IN1
RGB IN2
RGB OUT
CB/PB
AUDIO IN2
VIDEO
CR/PR S-VIDEO
USB
COMPONENT VIDEO
CONTROL
L
M
L USB
USB B type jack
3
1
2
Pin
1
2
3
4
Signal
TECHNICAL
4
+5V
- Data
+ Data
Ground
M CONTROL
D-sub 9pin plug
9
5
8
4
7
3
6
2
1
• About the details of RS-232C communication, please refer to the following page.
Pin
Signal
1 (No connection)
2 RD
3 TD
Pin
Signal
4 (No connection)
5 Ground
6 (No connection)
Pin
Signal
7 RTS
8 CTS
9 (No connection)
5
RS-232C Communication
RS-232C Communication
9
5
8
4
7
3
6
2
1
1
2
6
CONTROL port
of the projector
RS-232C cable
- (1)
RD (2)
TD (3)
- (4)
GND (5)
- (6)
RTS (7)
CTS (8)
- (9)
3
7
4
8
5
9
RS-232C port
of the computer
(1) CD
(2) RD
(3) TD
(4) DTR
(5) GND
(6) DSR
(7) RTS
(8) DTS
(9) RI
Connecting the cable
Turn off the projector and the computer.
1.
Connect the CONTROL port of the projector with a RS-232C port of the
2. computer by a RS-232C cable. Use the cable that fulfills the specification
shown in the previous page.
Turn the computer on, and after the computer has started up turn the
projector on.
3.
Communications setting
19200bps, 8N1
1. Protocol
Consist of header (7 bytes) + command data (6 bytes).
2. Header
BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
CRC_low : Lower byte of CRC flag for command data
CRC_high : Upper byte of CRC flag for command data
3. Command data
Command data chart
byte_0
byte_1
byte_2
byte_3
byte_4
byte_5
Action
Type
Setting code
low
high
low
high
low
high
Action (byte_0 - 1)
Action
Classification
Content
1
SET
Change setting to desired value.
2
GET
Read projector internal setup value.
4
INCREMENT Increment setup value by 1.
5
DECREMENT Decrement setup value by 1.
6
EXECUTE
Run a command.
6
Requesting projector status (Get command)
(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+
‘00H’ +‘00H’) from the computer to the projector.
(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
Changing the projector settings (Set command)
(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) +
setting code (2 bytes)) from the computer to the projector.
(2) The projector changes the setting based on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Using the projector default settings (Reset Command)
(1) The computer sends the default setting code Header + Command data (‘06H’+
‘00H’ + type (2 bytes) +‘00H’+‘00H’) to the projector.
(2) The projector changes the specified setting to the default value.
(3) The projector returns the response code ‘06H’ to the computer.
Increasing the projector setting value (Increment command)
(1) The computer sends the increment code Header + Command data (‘04H’+
‘00H’+ type (2 bytes) +‘00H’+‘00H’) to the projector.
(2) The projector in creases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Decreasing the projector setting value (Decrement command)
(1) The computer sends the decrement code Header + Command data (‘05H’+
‘00H’+ type (2 bytes) +‘00H’ + ‘00H’) to the projector.
(2) The projector decreases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
When the projector cannot understand the received command
When the projector cannot understand the received command, the error code ‘15H’
is sent back to the computer.
Sometimes the projector cannot properly receive the command. In such a
case, the command is not executed and the error code ‘15H’ is sent back to the
computer. If this error code is returned, send the same command again.
When the projector cannot execute the received command.
When the projector cannot execute the received command, the error code ‘1cH’
+ ‘xxxxH’ is sent back to the computer. When the data length is greater than
indicated by the data length code, the projector ignore the excess data code.
Conversely when the data length is shorter than indicated by the data length
code, an error code will be returned to the computer.
NOTE • Operation cannot be guaranteed when the projector receives an undefined
command or data.
• Provide an interval of at least 40ms between the response code and any other code.
• The projector outputs test data when the power supply is switched ON, and when the
lamp is lit. Ignore this data.
• Commands are not accepted during warm-up.
7
TECHNICAL
RS-232C Communication (continued)
RS-232C Communication (continued)
Names
Power
Operation Type
Set
Set
BRIGHT Reset
CONTRAST
CONTRAST Reset
MODE
BE EF
03
06 00
2A D3
01 00
00 60
00 00
03
06 00
BA D2
01 00
00 60
01 00
BE EF
03
06 00
19 D3
02 00
00 60
00 00
RGB IN1
(Example return)
00 00
(Off)
BE EF
03
BE EF
03
01 00
02 00
(On)
(Cool down)
06 00
FE D2
01 00
00 20
00 00
06 00
00 20
04 00
3E D0
01 00
VIDEO
BE EF
03
06 00
6E D3
01 00
00 20
01 00
S-VIDEO
BE EF
03
06 00
9E D3
01 00
00 20
02 00
COMPONENT
05 00
BE EF
03
06 00
AE D1
01 00
00 20
Get
BE EF
03
06 00
CD D2
02 00
00 20
00 00
Get
BE EF
03
06 00
D9 D8
02 00
20 60
00 00
01 00
02 00
(Cover error)
(Fan error)
05 00
06 00
(Air flow error)
(Lamp time error)
09 00
10 00
(Filter missing error)(Inner Sencer error)
03 00
(Lamp error)
07 00
(Cool error)
Get
BE EF
03
06 00
89 D2
02 00
03 20
00 00
Increment
BE EF
03
06 00
EF D2
04 00
03 20
00 00
Decrement
BE EF
03
06 00
3E D3
05 00
03 20
00 00
Execute
BE EF
03
06 00
58 D3
06 00
00 70
00 00
00 00
Get
BE EF
03
06 00
FD D3
02 00
04 20
Increment
BE EF
03
06 00
9B D3
04 00
04 20
00 00
Decrement
BE EF
03
06 00
4A D2
05 00
04 20
00 00
00 00
Execute
Set
Command Data
Type
Setting Code
BE EF
(Example return)
00 00
(Normal)
04 00
(Temp error)
08 00
(Filter error)
BRIGHT
Action
Turn off
RGB IN2
Error Status
CRC
Turn on
Get
Input Source
Header
BE EF
03
06 00
A4 D2
06 00
01 70
NORMAL
BE EF
03
06 00
23 F6
01 00
BA 30
00 00
CINEMA
BE EF
03
06 00
B3 F7
01 00
BA 30
01 00
DYNAMIC
BE EF
03
06 00
E3 F4
01 00
BA 30
04 00
Get
BE EF
03
06 00
10 F6
02 00
BA 30
00 00
(Example return)
GAMMA
Set
#1 DEFAULT
BE EF
00 00
01 00
(Normal) (Cinema)
03
06 00
07 E9
#1 CUSTOM
BE EF
03
06 00
#2 DEFAULT
BE EF
03
#2 CUSTOM
BE EF
03
#3 DEFAULT
BE EF
#3 CUSTOM
Get
8
04 00
(Dynamic)
01 00
10 00
(Custom)
A1 30
20 00
07 FD
01 00
A1 30
10 00
06 00
97 E8
01 00
A1 30
21 00
06 00
97 FC
01 00
A1 30
11 00
03
06 00
67 E8
01 00
A1 30
22 00
BE EF
03
06 00
67 FC
01 00
A1 30
12 00
BE EF
03
06 00
F4 F0
02 00
A1 30
00 00
RS-232C Communication (continued)
User Gamma Pattern
Operation Type
Set
User Gamma Point 1
User Gamma Point 2
User Gamma Point 3
User Gamma Point 4
User Gamma Point 5
User Gamma Point 6
User Gamma Point 7
User Gamma Point 8
COLOR TEMP
COLOR TEMP GAIN R
Set
Header
CRC
Action
Command Data
Type
Setting Code
Off
BE EF
03
06 00
FB FA
01 00
80 30
00 00
9 step gray scale
BE EF
03
06 00
6B FB
01 00
80 30
01 00
15 steps gray scale
BE EF
03
06 00
9B FB
01 00
80 30
02 00
Ramp
BE EF
03
06 00
0B FA
01 00
80 30
03 00
Get
BE EF
03
06 00
C8 FA
02 00
80 30
00 00
Get
BE EF
03
06 00
08 FE
02 00
90 30
00 00
Increment
BE EF
03
06 00
6E FE
04 00
90 30
00 00
Decrement
BE EF
03
06 00
BF FF
05 00
90 30
00 00
00 00
Get
BE EF
03
06 00
F4 FF
02 00
91 30
Increment
BE EF
03
06 00
92 FF
04 00
91 30
00 00
Decrement
BE EF
03
06 00
43 FE
05 00
91 30
00 00
Get
BE EF
03
06 00
B0 FF
02 00
92 30
00 00
Increment
BE EF
03
06 00
D6 FF
04 00
92 30
00 00
Decrement
BE EF
03
06 00
07 FE
05 00
92 30
00 00
Get
BE EF
03
06 00
4C FE
02 00
93 30
00 00
Increment
BE EF
03
06 00
2A FE
04 00
93 30
00 00
Decrement
BE EF
03
06 00
FB FF
05 00
93 30
00 00
00 00
Get
BE EF
03
06 00
38 FF
02 00
94 30
Increment
BE EF
03
06 00
5E FF
04 00
94 30
00 00
Decrement
BE EF
03
06 00
8F FE
05 00
94 30
00 00
00 00
Get
BE EF
03
06 00
C4 FE
02 00
95 30
Increment
BE EF
03
06 00
A2 FE
04 00
95 30
00 00
Decrement
BE EF
03
06 00
73 FF
05 00
95 30
00 00
00 00
Get
BE EF
03
06 00
80 FE
02 00
96 30
Increment
BE EF
03
06 00
E6 FE
04 00
96 30
00 00
Decrement
BE EF
03
06 00
37 FF
05 00
96 30
00 00
00 00
Get
BE EF
03
06 00
7C FF
02 00
97 30
Increment
BE EF
03
06 00
1A FF
04 00
97 30
00 00
Decrement
BE EF
03
06 00
CB FE
05 00
97 30
00 00
LOW
BE EF
03
06 00
6B F4
01 00
B0 30
01 00
MIDDLE
BE EF
03
06 00
9B F4
01 00
B0 30
02 00
HIGH
BE EF
03
06 00
0B F5
01 00
B0 30
03 00
CUSTOM
BE EF
03
06 00
3B F8
01 00
B0 30
10 00
Get
BE EF
03
06 00
C8 F5
02 00
B0 30
00 00
00 00
Get
BE EF
03
06 00
34 F4
02 00
B1 30
Increment
BE EF
03
06 00
52 F4
04 00
B1 30
00 00
Decrement
BE EF
03
06 00
83 F5
05 00
B1 30
00 00
TECHNICAL
Names
9
RS-232C Communication (continued)
Names
Operation Type
COLOR TEMP GAIN G
COLOR TEMP GAIN B
COLOR TEMP
OFFSET R
COLOR TEMP
OFFSET G
COLOR TEMP
OFFSET B
COLOR
Header
CRC
Action
Command Data
Type
Setting Code
Get
BE EF
03
06 00
70 F4
02 00
B2 30
Increment
BE EF
03
06 00
16 F4
04 00
B2 30
00 00
00 00
Decrement
BE EF
03
06 00
C7 F5
05 00
B2 30
00 00
00 00
Get
BE EF
03
06 00
8C F5
02 00
B3 30
Increment
BE EF
03
06 00
EA F5
04 00
B3 30
00 00
Decrement
BE EF
03
06 00
3B F4
05 00
B3 30
00 00
00 00
Get
BE EF
03
06 00
04 F5
02 00
B5 30
Increment
BE EF
03
06 00
62 F5
04 00
B5 30
00 00
Decrement
BE EF
03
06 00
B3 F4
05 00
B5 30
00 00
00 00
Get
BE EF
03
06 00
40 F5
02 00
B6 30
Increment
BE EF
03
06 00
26 F5
04 00
B6 30
00 00
Decrement
BE EF
03
06 00
F7 F4
05 00
B6 30
00 00
00 00
Get
BE EF
03
06 00
BC F4
02 00
B7 30
Increment
BE EF
03
06 00
DA F4
04 00
B7 30
00 00
Decrement
BE EF
03
06 00
0B F5
05 00
B7 30
00 00
Get
BE EF
03
06 00
B5 72
02 00
02 22
00 00
Increment
BE EF
03
06 00
D3 72
04 00
02 22
00 00
Decrement
BE EF
03
06 00
02 73
05 00
02 22
00 00
COLOR Reset
Execute
BE EF
03
06 00
80 D0
06 00
0A 70
00 00
TINT
Get
BE EF
03
06 00
49 73
02 00
03 22
00 00
Increment
BE EF
03
06 00
2F 73
04 00
03 22
00 00
Decrement
BE EF
03
06 00
FE 72
05 00
03 22
00 00
TINT Reset
Execute
BE EF
03
06 00
7C D1
06 00
0B 70
00 00
SHARPNESS
Get
BE EF
03
06 00
F1 72
02 00
01 22
00 00
SHARPNESS Reset
PROGRESSIVE
Increment
BE EF
03
06 00
97 72
04 00
01 22
00 00
Decrement
BE EF
03
06 00
46 73
05 00
01 22
00 00
Execute
Set
BE EF
03
06 00
C4 D0
06 00
09 70
00 00
TURN OFF
BE EF
03
06 00
4A 72
01 00
07 22
00 00
TV
BE EF
03
06 00
DA 73
01 00
07 22
01 00
FILM
BE EF
03
06 00
2A 73
01 00
07 22
02 00
BE EF
03
06 00
79 72
02 00
07 22
00 00
1
BE EF
03
06 00
0E D7
01 00
14 20
00 00
2
BE EF
03
06 00
9E D6
01 00
14 20
01 00
3
BE EF
03
06 00
6E D6
01 00
14 20
02 00
4
BE EF
03
06 00
FE D7
01 00
14 20
03 00
1
BE EF
03
06 00
F2 D6
01 00
15 20
00 00
2
BE EF
03
06 00
62 D7
01 00
15 20
01 00
3
BE EF
03
06 00
92 D7
01 00
15 20
02 00
4
BE EF
03
06 00
02 D6
01 00
15 20
03 00
4:3
BE EF
03
06 00
9E D0
01 00
08 20
00 00
Get
MY MEMORY Load
MY MEMORY Save
ASPECT
10
Set
Set
Set
16:9
BE EF
03
06 00
0E D1
01 00
08 20
01 00
SMALL
BE EF
03
06 00
FE D1
01 00
08 20
02 00
NORMAL
BE EF
03
06 00
5E DD
01 00
08 20
10 00
Get
BE EF
03
06 00
AD D0
02 00
08 20
00 00
RS-232C Communication (continued)
Operation Type
OVER SCAN
Header
CRC
Action
Command Data
Type
Setting Code
Get
BE EF
03
06 00
91 70
02 00
09 22
Increment
BE EF
03
06 00
F7 70
04 00
09 22
00 00
Decrement
BE EF
03
06 00
26 71
05 00
09 22
00 00
OVER SCAN Reset
Execute
BE EF
03
06 00
EC D9
06 00
27 70
00 00
V POSITION
Get
BE EF
03
06 00
0D 83
02 00
00 21
00 00
Increment
BE EF
03
06 00
6B 83
04 00
00 21
00 00
Decrement
BE EF
03
06 00
BA 82
05 00
00 21
00 00
V POSITION Reset
Execute
BE EF
03
06 00
E0 D2
06 00
02 70
00 00
H POSITION
Get
BE EF
03
06 00
F1 82
02 00
01 21
00 00
Increment
BE EF
03
06 00
97 82
04 00
01 21
00 00
H POSITION Reset
H PHASE
H SIZE
00 00
Decrement
BE EF
03
06 00
46 83
05 00
01 21
00 00
Execute
BE EF
03
06 00
1C D3
06 00
03 70
00 00
00 00
Get
BE EF
03
06 00
49 83
02 00
03 21
Increment
BE EF
03
06 00
2F 83
04 00
03 21
00 00
Decrement
BE EF
03
06 00
FE 82
05 00
03 21
00 00
Get
BE EF
03
06 00
B5 82
02 00
02 21
00 00
Increment
BE EF
03
06 00
D3 82
04 00
02 21
00 00
00 00
Decrement
BE EF
03
06 00
02 83
05 00
02 21
H SIZE Reset
Execute
BE EF
03
06 00
68 D2
06 00
04 70
00 00
AUTO ADJUST
Execute
BE EF
03
06 00
91 D0
06 00
0A 20
00 00
AUTO
BE EF
03
06 00
0E 72
01 00
04 22
00 00
RGB
BE EF
03
06 00
9E 73
01 00
04 22
01 00
SMPTE240
BE EF
03
06 00
6E 73
01 00
04 22
02 00
REC709
BE EF
03
06 00
FE 72
01 00
04 22
03 00
REC601
BE EF
03
06 00
CE 70
01 00
04 22
04 00
Get
BE EF
03
06 00
3D 72
02 00
04 22
00 00
COMPONENT
BE EF
03
06 00
4A D7
01 00
17 20
00 00
SCART RGB
BE EF
03
06 00
DA D6
01 00
17 20
01 00
BE EF
03
06 00
79 D7
02 00
17 20
00 00
AUTO
BE EF
03
06 00
9E 75
01 00
00 22
0A 00
NTSC
BE EF
03
06 00
FE 71
01 00
00 22
04 00
PAL
BE EF
03
06 00
6E 70
01 00
00 22
05 00
SECAM
BE EF
03
06 00
6E 75
01 00
00 22
09 00
NTSC4.43
BE EF
03
06 00
5E 72
01 00
00 22
02 00
M-PAL
BE EF
03
06 00
FE 74
01 00
00 22
08 00
N-PAL
BE EF
03
06 00
0E 71
01 00
00 22
07 00
BE EF
03
06 00
0D 73
02 00
00 22
00 00
COLOR SPACE
COMPONENT
Set
Set
Get
VIDEO FORMAT
Set
Get
11
TECHNICAL
Names
RS-232C Communication (continued)
Names
FRAME LOCK
Operation Type
Set
KEYSTONE V
KEYSTONE V Reset
WHISPER
MIRROR
Set
Set
VOLUME
MUTE
LANGUAGE
12
Set
Set
Header
CRC
Action
Command Data
Type
Setting Code
TURN OFF
BE EF
03
06 00
CB D6
01 00
14 30
00 00
TURN ON
BE EF
03
06 00
5B D7
01 00
14 30
01 00
Get
BE EF
03
06 00
F8 D6
02 00
14 30
00 00
Get
BE EF
03
06 00
B9 D3
02 00
07 20
00 00
Increment
BE EF
03
06 00
DF D3
04 00
07 20
00 00
Decrement
BE EF
03
06 00
0E D2
05 00
07 20
00 00
Execute
BE EF
03
06 00
08 D0
06 00
0C 70
00 00
NORMAL
BE EF
03
06 00
3B 23
01 00
00 33
00 00
WHISPER
BE EF
03
06 00
AB 22
01 00
00 33
01 00
Get
BE EF
03
06 00
08 23
02 00
00 33
00 00
NORMAL
BE EF
03
06 00
C7 D2
01 00
01 30
00 00
H:INVERT
BE EF
03
06 00
57 D3
01 00
01 30
01 00
V:INVERT
BE EF
03
06 00
A7 D3
01 00
01 30
02 00
H&V:INVERT
BE EF
03
06 00
37 D2
01 00
01 30
03 00
Get
BE EF
03
06 00
F4 D2
02 00
01 30
00 00
Get
BE EF
03
06 00
31 D3
02 00
01 20
00 00
Increment
BE EF
03
06 00
57 D3
04 00
01 20
00 00
Decrement
BE EF
03
06 00
86 D2
05 00
01 20
00 00
TURN OFF
BE EF
03
06 00
46 D3
01 00
02 20
00 00
TURN ON
BE EF
03
06 00
D6 D2
01 00
02 20
01 00
Get
BE EF
03
06 00
75 D3
02 00
02 20
00 00
00 00
ENGLISH
BE EF
03
06 00
F7 D3
01 00
05 30
FRANÇAIS
BE EF
03
06 00
67 D2
01 00
05 30
01 00
DEUTSCH
BE EF
03
06 00
97 D2
01 00
05 30
02 00
ESPAÑOL
BE EF
03
06 00
07 D3
01 00
05 30
03 00
ITALIANO
BE EF
03
06 00
37 D1
01 00
05 30
04 00
NORSK
BE EF
03
06 00
A7 D0
01 00
05 30
05 00
NEDERLANDS
BE EF
03
06 00
57 D0
01 00
05 30
06 00
PORTUGUÊS
BE EF
03
06 00
C7 D1
01 00
05 30
07 00
BE EF
03
06 00
37 D4
01 00
05 30
08 00
BE EF
03
06 00
A7 D5
01 00
05 30
09 00
BE EF
03
06 00
57 D5
01 00
05 30
0A 00
SVENSKA
BE EF
03
06 00
C7 D4
01 00
05 30
0B 00
PУCCKИЙ
BE EF
03
06 00
F7 D6
01 00
05 30
0C 00
SUOMI
BE EF
03
06 00
67 D7
01 00
05 30
0D 00
POLSKI
BE EF
03
06 00
97 D7
01 00
05 30
0E 00
Get
BE EF
03
06 00
C4 D3
02 00
05 30
00 00
RS-232C Communication (continued)
Operation Type
MENU POSITION H
MENU POSITION H
Reset
MENU POSITION V
MENU POSITION V
Reset
OSD BRIGHT
BLANK
BLANK On/Off
START UP
My Screen LOCK
Message
AUTO SEARCH
AUTO POWER OFF
Set
Set
Set
Set
Set
Set
Header
CRC
Action
Command Data
Type
Setting Code
Get
BE EF
03
06 00
04 D7
02 00
15 30
00 00
Increment
BE EF
03
06 00
62 D7
04 00
15 30
00 00
Decrement
BE EF
03
06 00
B3 D6
05 00
15 30
00 00
Execute
BE EF
03
06 00
DC C6
06 00
43 70
00 00
Get
BE EF
03
06 00
40 D7
02 00
16 30
00 00
Increment
BE EF
03
06 00
26 D7
04 00
16 30
00 00
Decrement
BE EF
03
06 00
F7 D6
05 00
16 30
00 00
Execute
BE EF
03
06 00
A8 C7
06 00
44 70
00 00
Get
BE EF
03
06 00
A8 D5
02 00
18 30
00 00
Increment
BE EF
03
06 00
CE D5
04 00
18 30
00 00
Decrement
00 00
BE EF
03
06 00
1F D4
05 00
18 30
My Screen
BE EF
03
06 00
FB CA
01 00
00 30
20 00
ORIGINAL
BE EF
03
06 00
FB E2
01 00
00 30
40 00
03 00
BLUE
BE EF
03
06 00
CB D3
01 00
00 30
WHITE
BE EF
03
06 00
6B D0
01 00
00 30
05 00
BLACK
BE EF
03
06 00
9B D0
01 00
00 30
06 00
Get
BE EF
03
06 00
08 D3
02 00
00 30
00 00
TURN OFF
BE EF
03
06 00
FB D8
01 00
20 30
00 00
TURN ON
BE EF
03
06 00
6B D9
01 00
20 30
01 00
Get
BE EF
03
06 00
C8 D8
02 00
20 30
00 00
My Screen
BE EF
03
06 00
CB CB
01 00
04 30
20 00
ORIGINAL
BE EF
03
06 00
0B D2
01 00
04 30
00 00
TURN OFF
BE EF
03
06 00
9B D3
01 00
04 30
01 00
Get
BE EF
03
06 00
38 D2
02 00
04 30
00 00
TURN OFF
BE EF
03
06 00
3B EF
01 00
C0 30
00 00
TURN ON
BE EF
03
06 00
AB EE
01 00
C0 30
01 00
Get
BE EF
03
06 00
08 EF
02 00
C0 30
00 00
TURN OFF
BE EF
03
06 00
8F D6
01 00
17 30
00 00
TURN ON
BE EF
03
06 00
1F D7
01 00
17 30
01 00
Get
BE EF
03
06 00
BC D6
02 00
17 30
00 00
TURN OFF
BE EF
03
06 00
B6 D6
01 00
16 20
00 00
TURN ON
BE EF
03
06 00
26 D7
01 00
16 20
01 00
Get
BE EF
03
06 00
85 D6
02 00
16 20
00 00
Get
BE EF
03
06 00
08 86
02 00
10 31
00 00
Increment
BE EF
03
06 00
6E 86
04 00
10 31
00 00
Decrement
BE EF
03
06 00
BF 87
05 00
10 31
00 00
13
TECHNICAL
Names
RS-232C Communication (continued)
Names
Operation Type
Header
CRC
Action
Command Data
Type
Setting Code
LAMP TIME
Get
BE EF
03
06 00
C2 FF
02 00
90 10
00 00
LAMP TIME Reset
Execute
BE EF
03
06 00
58 DC
06 00
30 70
00 00
FILTER TIME
Get
BE EF
03
06 00
C2 F0
02 00
A0 10
00 00
FILER TIME Reset
Execute
BE EF
03
06 00
98 C6
06 00
40 70
00 00
MAGNIFY
Get
BE EF
03
06 00
7C D2
02 00
07 30
00 00
Increment
BE EF
03
06 00
1A D2
04 00
07 30
00 00
Decrement
FREEZE
14
Set
BE EF
03
06 00
CB D3
05 00
07 30
00 00
NORMAL
BE EF
03
06 00
83 D2
01 00
02 30
00 00
FREEZE
BE EF
03
06 00
13 D3
01 00
02 30
01 00
Get
BE EF
03
06 00
B0 D2
02 00
02 30
00 00
Audio Visual Products
Dukane Corporation
Audio Visual Products Division
2900 Dukane Drive
St. Charles, IL 60174-3395
E-mail: avsales@dukcorp.com
Phone: (630) 762-4040
Orders: (800) 676-2485
Information: (800) 676-2486
Fax: (630) 584-5156
Parts & Service: (800) 676-2487
Fax: (630) 584-0984
Part # 401-8063/8755C-00