PiXORD Dual Streaming Network Camera P

PiXORD
Dual Streaming Network Camera
P-505
User Manual
1
Preface .....................................................................................................................3
1.
Chapter 1 Introduction To Your Camera ........................4
1.1
1.2
1.3
1.4
2.
Checking the Package Contents ....................................................4
Getting to Know Your Camera ......................................................5
Features and Benefits .......................................................................7
System Requirement ........................................................................9
Chapter 2 Hardware Installation ........................................10
2.1
2.2
2.3
3.
Installing Camera Stand ................................................................10
Connecting the Camera to LAN/WLAN...................................11
Application of the Camera ............................................................12
Chapter 3 Accessing the Camera .......................................13
3.1
3.2
3.3
4.
Using IP Installer .............................................................................13
Accessing the Camera ....................................................................14
Configuring the IP address of PC................................................16
Chapter 4 Configuring the Camera ..................................17
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
5.
Using the Web Configuration.......................................................17
Using Smart Wizard .......................................................................18
Basic Setup .......................................................................................21
Network Settings .............................................................................24
Setting up Video & Audio .............................................................29
Event Server Configuration ..........................................................32
Motion Detect ..................................................................................35
Event Config ....................................................................................36
Tools ...................................................................................................39
USB ....................................................................................................40
Information .......................................................................................41
Appendix ..............................................................................................42
2
Preface
Pixord P505 is a powerful dual-codec MPEG4/MJPEG network camera with one way or two
way audio function that provides the high quality image and on-the-spot audio via the internet
connection. The infrared LEDs and light sensor (optional) enable the camera to capture
images even in dark environment. The camera can be installed as a standalone system with
your application environment easily and quickly and supports remote management function so
that you can access and control it using a web browser on your PC.
Chapter 1 Introduction to Your Camera describes the features of the camera. You will also
know the components and functions of the camera.
Chapter 2 Hardware Installation helps you install the camera according to your application
environment. You can use this camera at home, at work and anywhere you want.
Chapter 3 Accessing the Camera lets you start using your camera without problem. The
camera can be set up easily and work within your network environment instantly.
Chapter 4 Configuring the Camera guides you through the configuration of the camera using
the web browser on your PC.
Chapter 5 Appendix provides the specification of the camera and some useful information for
using your camera.
Note: The illustrations and configuration values in this guide are for reference only. The actual
settings depend on your practical application of the camera.
3
1. Chapter 1 Introduction To Your Camera
1.1 Checking the Package Contents
Check the items contained in the package carefully. You should have the following.
One MPEG4/MJPEG Network Camera (Wireless)
One AC Power Adapter
One External Antenna (for wireless camera)
One Camera Stand
One Ethernet Cable (RJ-45 type)
One Installation CD-ROM
One Quick Installation Guide
Note: Once any item contained is damaged or missing, contact the authorized dealer of your
locale.
4
1.2 Getting to Know Your Camera
Front View
* The camera’s USB port supports WCN (Windows Connect Now) technology, which allows
you to use the notebook computer to set up and store your wireless networking configuration
on the USB storage device and then retrieve the wireless settings when you connect the USB
storage device to the camera.
Note: After long pressing the Unmount button for four seconds the Power LED starts flashing.
When the Power LED resumes the steady amber light, you can remove the USB device safely.
5
Rear View
6
1.3 Features and Benefits
‹
MPEG4/MJPEG Dual-code Supported
The camera provides you with excellent images by the MPEG4/MJPEG dual-codec
selectable technology, allowing you to adjust image size and quality and bit rate
according to the networking environment.
‹
1-way/2-way Audio Capability
The built-in microphone of the camera provides on-the-spot audio via the internet,
allowing you to monitor the on-site voice. In addition, you can connect an external
speaker to the camera to speak through the camera (for 2-way audio model only); the
camera is embedded with an echo cancellation processor to provide a better sound
quality.
‹
Day& Night Surveillance Support (optional)
The six infrared LEDs around the standard lens assembly (optional) enable the camera
to capture crystal clear images in the dark environment or at night. When the light sensor
detects the environmental light level becomes low, the camera captures the images in
black & white using these infrared LEDs.
‹
Supports Multiple Profiles
The camera supports multiple profiles simultaneously so that you can separately set up
different image settings (such as image quality and frame rate) for the three video types
of the camera: MPEG4, MJPEG and 3GPP.
‹
Support RTSP
The camera supports RTSP (Real Time Streaming Protocol), which is a technology that
allows you to view streaming media via the network. You can view the real-time video
with the Quick Time player or Real Player. To view the real-time streaming image on your
computer, open the web browser and enter the RTSP link: rtsp://(IP address of the
camera)/mpeg4
‹
Remote Control Support
By using a standard web browser, the administrator can easily change the configuration
of the camera via intranet or internet. In addition, the camera can be upgrade remotely
when a new firmware is available. The users are also allowed to monitor the image and
take snapshots via the network.
‹
Supports Connection to the External Devices
With the auxiliary Input/Output connectors, you can connect the camera to a variety of
external devices such as the external speaker and USB device.
7
‹
Multiple Platform Supported
The camera supports multiple network protocols including TCP/IP, SMTP email, HTTP
and other internet related protocols. Therefore you can use the camera in a mixed
operating system environment such as Windows 2000 and Windows XP.
‹
Multiple Application Supported
Through the remote access technology, you can use the cameras to monitor various and
places for your own purposes.
For example, babies at home, patients in the hospital, offices, banks and more. The
camera can capture both still images and video clips so that you can keep the archives
and restore them at any time.
8
1.4 System Requirement
‹
Networking
LAN: 10Base-T Ethernet or 100Base-TX Fast Ethernet
WLAN: IEEE 802.11b/g (for wireless model)
‹
Accessing the Camera using Web Browser
Platform:
Microsoft Windows 98SE/ME/2000/XP
CPU:
Intel Pentium III 350MHz or above
RAM:
512MB
Resolution:
800X600 or above
User Interface: Microsoft Internet Explorer 5.0 or above
9
2. Chapter 2 Hardware Installation
2.1 Installing Camera Stand
The camera comes with a camera stand, which uses a swivel ball screw head to lock to the
camera’s screw hole. When the camera stand is attached, you can place the camera
anywhere by mounting the camera through the three screw holes locates in the base of the
camera stand.
The Camera Stand
10
2.2 Connecting the Camera to LAN/WLAN
Use the provided Ethernet cable to connect
the camera to your local area network (LAN).
When you connect the AC power adaptor, the
camera is powered on automatically. You can
verify the power statues from the Power LED
on the front panel of the camera. Once
connected, the link LED starts flashing green
light and the camera is on standby and ready
to use now.
If you use a wireless network (wireless model
only) in your application environment, you need
to attach the included external antenna to the
camera. When the camera is powered on, the
camera will automatically search any access
point with “default” SSID.
Note: If the camera cannot connect to your wireless network, you need to install the camera
and proceed with WLAN settings.
11
2.3 Application of the Camera
The camera can be applied in multiple applications, including:
‹
Monitor local and remote places and objects via internet or intranet.
‹
Capture still images and video clips remotely
‹
Upload images or send email messages with still images attached.
The following diagram explains one of the typical applications for your camera and provides a
basic example for installing camera.
12
3. Chapter 3 Accessing the Camera
3.1 Using IP Installer
The camera comes with a conveniently utility, IP Installer, which is included in the installation
CD-ROM, allowing you to search the camera on your network easily.
1. Insert the installation CD into your computer CD-ROM drive to initiate the Auto-Run
program.
2. Click the IP Installer item to launch the utility. The control panel will appear as below.
3. Click on Tool > Search Network Device to find all connected cameras in the LAN.
4. Right click on the selected camera and choose “Open Web” to open the web page of the
camera.
13
3.2 Accessing the Camera
Whenever you want to access the camera:
1. Open the Web browser on your computer (for example, Microsoft Internet Explorer in this
guide).
2. Type the default IP address (192.168.0.30) or the IP address found by IP Installer in the
address bar then press [Enter].
3. When the login window appears, enter the default user name (admin) and password (admin)
and press OK to access to the main screen of the camera’s web configuration.
Note: If you are first time accessing the camera, you will be asked to install a new plug-in for
the camera. Permission request depends on the internet security settings of your computer.
Click YES to proceed.
14
After you login into the web configuration of the camera, the main page will appear as below:
Live View/Setup
Camera Information
Switch
Zoom In Buttons
Nightmode Button
Compression
Buttons
Function Buttons
Live View Image
The main page of the web configuration provides you with many useful information and
functions, including:
‹
Camera Information – Display the camera’s location and the current date & time. The
information can be modified in the web configuration.
‹
Live View Image – Displays the real time image of the connected camera.
‹
Live View/Setup Switch – Click Setup to configure the camera. For details, see Chapter
4
‹
Compression Buttons – Select to transmit and record the video using MPEG4 or
MJPEG compression.
‹
Function Buttons – Use these buttons to control the audio and video functions.
Manual Record: Allows you to record and save a video clip.
Snapshot: Allows you to capture and save a still image.
Browser: Allows assign the destination folder to store the video clips and still images.
Talk: Allows you to speak out through the camera. Please note that this button displays
only for the 2-way audio model and only one user is allowed to use this function at a time.
Listen: Allows you receive the on-site sound and voice from the camera.
‹
Zoom In Buttons – Click the buttons to zoom in the live view image by 1x, 2x and 3x.
‹
Night Mode Button – Click the button to enable the “nightshot mode” to deliver clearer
images in the dark environment. However, this will reduce the frame rate of video setting.
15
3.3 Configuring the IP address of PC
If you are failed to access to the camera, please check the IP address of your computer. When
you connect the camera to your computer directly to proceed with configuration of the camera,
you need to set up the IP addresses to be in the same segment for the two devices to
communicate.
1. On your computer, click start > Control panel to open the control panel window.
2. Double click “Network Connection” to open the Network Connection Window.
3. Right click “Local Area Connection” and then click “Properties” from the shortcut menu.
4. When the Local Area Connection Properties window appears, select the “General” tab.
5. Select Internet Protocol [TCP/IP] and then click “Properties” to bring up the internet
protocol [TCP/IP] Properties window.
6. To configure a fixed IP address that is within the segment of the camera, select the “Use
the following IP address” option. Then, enter an IP address into the empty field. The
suggested IP address is 192.168.0.x (x is 0~254 except 30) and the suggested Subnet
mask is 255.255.255.0
7. When you are finished, click “OK
16
4. Chapter 4 Configuring the Camera
4.1 Using the Web Configuration
You can access and manage the camera through the web browser and the provided software
application P6100. This chapter describes the web configuration and guides you through the
configuration of the camera by using the web browser.
To configure the camera, click SETUP on the main page of web configuration. The web
configuration will start from the basic page.
The web configuration contains the settings that are required for the camera in the left menu
bar, including Smart Wizard, Basic, Network, Video/Audio, Event Server, Motion detect, Event
Config, Tools, USB and Information.
17
4.2 Using Smart Wizard
The camera’s Smart Wizard lets you configure your camera easily and quickly. The wizard will
guide you through the necessary settings with detailed instructions on each step.
To start the wizard, click “Smart Wizard” in the left menu bar.
Step 1 Camera Settings
Enter the name for the
camera and place
Enter the administrator
password
Step 2 IP Settings
Select the IP setting according to
your network: DHCP, static IP or
PPPoE
18
Step 3 Email Settings
Enter the required information to
be able to send email with image.
Step 4 Wireless Networking (For wireless model)
Select Enable to enable the wireless
function of the camera and then
complete the required settings
19
Step 5 Confirm Settings
This step shows the configuration of your camera. When you confirm the settings, click “Apply”
to finish the wizard and reboot the camera. Otherwise, click “Prev” to go back to the previous
step(s) and change the settings; or click “Cancel” to end the wizard and discard the changes.
20
4.3 Basic Setup
The basic menu contains three sub-menus that provide the system settings for the camera
such as the camera name, location, date & time and user management.
Basic > System
‹
Basic
Camera Name: Enter a descriptive name for the camera.
Location: Enter a descriptive name for the location used by the camera.
Language Default: Choose English or Traditional Chinese
‹
Indicated LED
This item allows you to set the LED illumination as desired. There are two options:
NORMAL and OFF.
Basic > Date & Time
‹
Date & Time
Time Zone: Select the proper time zone for the region from the pull-down menu.
Synchronize with PC: Select this option and the date & time settings of the camera will be
synchronized with the connected computer.
Synchronize with NTP Server: Select this option and the time will be synchronized with
NTP server. You need to enter the IP address of the server and select the update the
interval in the following boxes.
Manual: Select this option to set the date and time manually.
21
Basic > User
‹
Administrator
To prevent unauthorized access to the camera’s web configuration, you are strongly
recommended to change the default administrator password. Type the administrator
password twice to set and confirm the password.
‹
General User
User Name: Enter the user’s name you want to add to use the camera.
Password: Enter the password for the new user.
When you are finished, click Add/Modify to add new user to the camera. To modify the
user’s information, select the one you want to modify from UserList and click Add/Modify.
UserList: Display the existing users of the camera. To delete a user, select the one you
want to delete and click Delete.
‹
Guest
User Name: Enter the guest’s name you want to add, giving permission for the user to
use the camera.
Password: Enter the password for the new guest.
UserList: Display the existing guests of the camera. To delete a user, select the one you
want to delete and click Delete.
Note: The “General User” can access the camera and control the Function buttons of the
camera’s web configuration; the “Guest” can only view the live view image from the main
page of the web configuration while accessing the camera. Only the “Administrator” is
allowed to configure the camera through the web configuration.
22
23
4.4 Network Settings
The Network menu contains three sub-menus that provide the network settings for the camera,
such as IP Setting, DDNS Setting, IP Filter and wireless network (for wireless model only).
24
Network > Network
‹
IP Setting
This item allows you to select the IP address mode and set up the related configuration.
DHCP: Select this option when your network uses the DHCP server. When the camera
starts up, it will be assigned an IP address from the DHCP server automatically.
Static IP: Select this option to assign the IP address for the camera directly. You can use
IP Installer to obtain the related setting values.
PPPoE: Select this option when you use a direct connection via the ADSL modem. You
should have a PPPoE account from your internet service provider (ISP). Enter the “User
Name” and “Password”. The camera will get an IP address from the ISP as starting up.
Note: Once the camera gets an IP address from the ISP as starting up, it automatically
sends a notification email to you. Therefore, when you select PPPoE as your connecting
type, you have to set up the email or DDNS configuration in advance.
‹
DDNS Setting
With the Dynamic DNS feature, you can assign a fixed host and domain name to a
dynamic internet IP address. Select the “Enable” option to enable this feature. Then,
select the provider from the pull-down list and enter the required information in the “Host
Name”, “User Name” and “Password” boxes. Please note that you have to sign up for
DDNS service provider first.
‹
UPnP
The camera supports UPnP (Universal Plug and Play) which is a set of computer network
protocols that enable the device-to-device interoperability. In addition, it supports port
auto mapping function so that you can access the camera if it is behind NAT router or
firewall. Select the “Enable” option to enable this feature.
25
‹
Ports Number
HTTP Port: The default HTTP port is 80.
RTSP Port: Configure the transmission of streaming data within the network. The default
RTSP (Real Time Streaming Protocol) port 554.
Note: If the camera is behind an NAT router or firewall, the suggested port to be used is
from 1024 to 65535.
Network > IP Filter
The IP Filter setting allows the administrator of the camera to limit the users within a certain
range of IP addresses to access the camera.
‹
Start/End IP Address
Assign a range of IP addresses that are not allowed to access the camera by entering the
“Start IP address” and “End IP address”. When you are finished, click “Add” to save the
range setting. You can repeat the action to assign multiple ranges for the camera.
For example, when you enter 192.168.0.50 in “Start IP Address” and 192.168.0.80 in
“End IP Address”, the user whose IP address located within 192.168.0.50~192.168.0.80
will not be allowed to access the camera.
‹
Deny IP List
The list displays the range setting(s) of IP addresses that are not allowed to access the
camera. To clear the setting, select a range of IP address from the list and click “Delete”.
26
Network > Wireless Setting (For wireless model only)
‹
Wireless
The camera supports WLAN while you use the wireless network. Select the “Enable”
option to enable this feature.
Network ID (SSID): Keep the default setting of this option to connect the camera to any
access point under the infrastructure network mode. To connect the camera to a
specified access point, set a SSID for the camera to correspond with the access point’s
ESS-ID. To connect the camera to an Ad-Hoc wireless workgroup, set the same wireless
channel and SSID to match with the computer’s configuration.
Click “Site Survey” to display the available wireless networks, so that you can easily
connect to one of the listed wireless networks.
List of searching results.
Wireless Mode: Select the type of wireless communication for the camera,
“Infrastructure” or “Ad-Hoc”.
Channel: Select the appropriate channel from the list.
Authentication: Select the authentication method to secure the camera from being used
by unauthorized user: Open, Shared-key, WPA-PSK and WPA2-PSK. The following table
explains the four options
27
If you select “Open” or “Shared-key” as the Authentication mode, you need to complete
the following settings:
Encryption: Select the WEP option to enable the data encryption feature to secure the
camera within the wireless network.
Format: Once you enable the Encryption feature, you need to determine the encryption
format by selecting ASCII or HEX. ASCII format causes each character you type to be
interpreted as an eight-bit value. Hex format causes each pair of characters you typed to
be interpreted as an eight-bit value in hexadecimal (base 16) notation.
Key Length: Select the WEP key length you use, 64 bits or 128 bits.
WEP Key 1~4: Enter the WEP key(s) in the following boxes.
If you select WPA-PSK or WPA2-PSK as the Authentication mode, you need to complete the
following settings.
Encryption: Select TKIP or AES. TKIP (Temporal Key Integrity Protocol) changes the
temporal key every 10000 packets to insure greater security than the standard WEP
security. AES (Advance Encryption Standard) is used to ensure the highest degree of
security and authenticity for digital information.
Pre-Shared Key: This is used to identify each other in the network. Enter the name in the
box and this name must match the Pre-shared key value in the remote device.
28
4.5 Setting up Video & Audio
The Video & Audio menu contains three sub-menus that provide the video and audio settings
for the camera.
Video & Audio > Camera
‹
Image Setting
Brightness: Adjust the brightness level from 0~100
Contrast: Adjust the contrast level from 0~100
Saturation: Adjust the colors level from 0~100
Click “Default” to restore the default settings of the three options above.
29
Mirror: Select the “Horizontal” option to mirror the image horizontal. Select the “Vertical”
option to mirror the image vertically.
Light Frequency: Select proper frequency according to camera’s location, 50Hz, 60Hz or
outdoor.
‹
Overlay Setting
Includes Date & Time: Select this option to display the date & time stamp on the live view
image.
Enable Opaque: Select this option to set a black background to the displayed date and
time stamp.
Video & Audio > Video
‹
MPEG4
Video Resolution: Select the desired video resolution from the three formats: VGA,
QVGA and QQVGA. The higher setting (VGA) obtains better video quality while it uses
more resource within your network.
Video Quality: Select the desired image quality from five levels: Lowest, Low, Medium,
High and highest.
Frame Rate: Select Auto or a proper setting depending on the your network status.
‹
MJPEG
Video Resolution: Select the desired video resolution from the three formats: VGA,
QVGA and QQVGA. The higher setting (VGA) obtains better video quality while it uses
more resource within your network
Video Quality: Select the desired image quality from five levels: Lowest, Low, Medium,
High and highest.
Frame Rate: Select Auto or a proper setting depending on the your network status.
Note: The camera supports both MPEG4 and MJPEG compression. MJPEG capture the
images in JPEG format, which require higher bandwidth to view smooth video. The
administrator can control the bandwidth of each connection well through the setting
options above.
30
‹
3GPP
The camera supports 3GPP specification. Select the “Disable” option to disable this
feature. Otherwise, select “3GPP Without Audio” or “3GPP With Audio” to transfer the
video clips without or with audio.
If you use a mobile phone that supports 3GPP, you can also view the real-time streaming
image captured by the camera on your phone (with the default player on the phone) by
entering the RTSP link: rtsp://(IP address of the camera)/3gp.
Video & Audio > Audio
‹
Camera Microphone In
Select the Enable option to enable the camera’s audio function, so that you can receive
the on-site sound and voice from the camera.
‹
Camera Speaker Out
This option is displayed when you connect a 2-way audio camera. Select the Enable
option to enable the camera’s external speaker function, so that the connected speaker
can play the sound and voice through the camera.
Volume: Set the speaker’s volume
31
4.6 Event Server Configuration
The Event Server menu contains three sub-menus that allow you to upload images to FTP,
send emails that include still images and store images to a NAS system.
When you complete the required settings for FTP, Email or Network Storage, click “Test” to test
the related configuration is correct or not. Once the camera connects to the server successfully,
click “Apply”.
Event Server Setting > FTP
‹
FTP
Host Address: Enter the IP address of the target FTP server.
Port Number: Enter the port number used for the FTP server.
User Name: Enter the user name to login into the FTP server.
Password: Enter the password to login into the FTP server
Directory path: Enter the destination folder for uploading the images. For example, /Test/
Passive Mode: Select the Enable option to enable passive mode.
32
Event Server Setting > Email
‹
Email
SMTP Server Address: Enter the mail server address. For example, mymail.com
Sender Email Address: Enter the email address of the user who will send the email. For
example, john@mymail.com
Sender user Name: Enter the user name to login the mail server
Sender Password: Enter the password to login the mail server.
Receiver#1 Email Address: Enter the first email address of the user who will receive the
email.
Receiver#2 Email Address: Enter the second email address of the user who will receive
the email.
33
Event Server Setting > Network Storage
‹
Net Storage
Samba Server Address: Enter the IP address of the Network Storage server
Share: Assign the folder on the Network Storage server to share the files to uses.
Path: Assign the path for uploading the files on the Network Storage server. For example,
/Test/
User Name: Enter the user name to login into the Network Storage server
Password: Enter the password to login into the Network Storage server.
Split By: When the file is too large to upload smoothly, use this option to split it by
selecting “File Size” or “Recording Time”.
When Disk Full: Select “Stop Recording” or “Recycle-Delete oldest Folder of File” when
the storage space on the Network Storage server is full.
34
4.7 Motion Detect
The motion Detect menu contains the command and option that allow you to enable and set up
the motion detection feature of the camera. The camera provides two detecting areas.
To enable the detecting area, select Window 1 or 2 from the pull-down list and then select
“Enable”. When the detecting area is enabled, you can use the mouse to move the detecting
area and change the area coverage.
Name: Assign a name to the detecting area.
Threshold: Move the slide bar to adjust the level for detecting motion to record video.
35
4.8 Event Config
The Event Config menu contains four sub-menus that provide the commands to configure
event profiles.
Event Configuration > General Setting
Snapshot/Recording Filename Prefix: You can assign a given prefix to each new
captured files. Otherwise, leave this option blank to use the default setting.
Network Storage Recording Time Per Even: Limit the recording time while you are using
the Network Storage solution.
Event Configuration > Arrange Schedule Profile
This sub-menu displays the scheduled profile(s). To customize the profile, click “Add” and then
enter a descriptive name for the profile in the prompt dialog window. After entering the profile
name, click “OK” and the profile is added to the Schedule Profile list. To delete the profile,
select the profile in the list and click “Delete”.
36
Profile Name: Display the profile name that you select in the Schedule Profile list.
Weekdays: Select the weekday(s) that you want to separately assign in the schedule
profile. The weekday that has been assigned will be displayed with green color.
Time List: Display the time period that you have assigned within the selected weekday.
To assign the same time period to every weekday, click “Add this to all weekdays”, click
“Delete this from all weekdays” to remove the selected time period from every weekday.
Click Delete to remove the selected time period.
Start/End Time: Enter the start and end time and then click “Add” to assign a time period
within the selected weekday.
Event Configuration > Motion Detect Trigger
Select the Enable option to enable the trigger function of the camera, so that you can send
captured images within the detecting area to the FTP server, email receiver, Network Storage
server or the connected USB device. You have to configure corresponding settings such as
FTP server and email server to enable this feature
Schedule Profile: Select a schedule profile from the pull-down list.
Action: Select the destination that the captures images will be sent to: Send Email, FTP
Upload, Record to Network Storage or Save Image to USB.
37
Event Configuration > schedule Trigger
You can separately configure the schedule for trigger function of the camera by Email, FTP or
Network Storage. Select the Enable option on each item and then select a Schedule Profile
from the pull-down list and set the Interval time.
Note: If the setting value of the “Network Storage Recording Time Per Event” option in General
Setting is longer than the “Interval” time in Network Storage Schedule, the recorded file will be
a continuous video clip.
For example, if you set the “Network Storage Recording Time Per Event” as 10 seconds and
the “Interval” as 5 seconds, recorded file becomes a non-stop video clip because the camera
will record a 10-second video clip every 5 seconds.
38
4.9 Tools
The Tools menu provides the commands that allow you to restart or reset the camera. You can
also backup and restore your configuration and upgrade the firmware for the camera.
‹
Factory Reset
Click “Reset” to restore all factory default settings for the camera
‹
System Reboot
Click “Reboot” to restart the camera just like turning the device off and on. The camera
configuration will be retained after rebooting
‹
Configuration
You can save your camera configuration as a backup file on your computer. Whenever
you want to resume the original settings, you can restore them by retrieving the backup
file.
Backup: Click “Get the backup file” to save the current configuration of the camera.
Restore: Click “Browse” to locate the backup file and then click “Restore”.
‹
Update Firmware
This item displays the current firmware version. You can upgrade the firmware for your
camera once you obtained a latest version of firmware.
Select the firmware: Click “Browse” to locate the backup file and then click “Update”
Note: Make sure to keep the camera connected to the power source during the process
of upgrading firmware, else the camera might be damaged because of upgrading failure.
39
4.10
USB
The USB menu provides the information and controls of the connected USB device.
‹
USB Dismount
To safely remove the connected USB device, you can press the dismount button for four
seconds on the camera or click “Dismount” from this item.
‹
USB Information
Display the total space and free space of the USB device.
‹
USB Setting
When Disk Full: Select “Stop Recording” or “Recycle-Delete Oldest Folder of file” when
the storage space on the USB device is full.
Note: The connected USB storage device can be only used to store still images.
40
4.11
Information
The Information menu displays the current configuration and events log of the camera.
‹
Device Info
Display the Basic, Video & Audio, Network and Wireless settings of the camera.
‹
System Log
The Logs table displays the events log recorded by the system.
41
5. Appendix
Specification
‹
‹
‹
‹
Image Sensor
Sensor
1/4” color CMOS
Resolution
640X480
Video
Compression
MPEG4/MJPEG
Video resolution
VGA/QVGA/QQVGA; 30FPS Max.
System Hardware
Processor
ARM9 base
RAM
32MB SDRAM
ROM
8MB NOR Flash
Power
DC 5V
Communication
LAN
10/100Mbps Fast Ethernet, auto-sensed, Auto-MDIX
WLAN
IEEE 802.11b/g
Protocol support
TCP/IP, UDP, ICMP, DHCP, NTP, DNS, DDNS, SMTP, FTP,
Samba, PPPoE, UPnP, RTP, RTSP and RTCP.
‹
User Interface
LAN
One RJ-45 port
Antenna
One external antenna
Reset
One Reset button
USB
USB 1.1 port, with one unmount button;
Power distribution: 500mA Max.
Support FAT, FAT32 file system
LEDs
‹
Power LED (amber); Link LED (green)
Audio
Input
Built-in MIC
Output
Headphone output jack (Mono)
Codec
PCM/AMR (AMR is for 3GPP only)
42
‹
‹
Software
OS Support
Windows 2000/XP/Vista
Browser
Internet Explorer 5.0 or above
Software
Ultra View for playback/recording/configuration features
Operating Environment
Temperature
Operation: 5°C ~ 45°C
Storage: -15°C ~ 60°C
Humidity
Operation: 20% ~ 85% non-condensing
Storage: 0% ~ 90% non-condensing
‹
EMI
FCC Class B, CE Class B
43