UltraLab_ULS_80D_Man.. - GENERAL ACOUSTICS Echosounding

UltraLab ULS 80D
User Manual Vers. 1.01
UltraLab® ULS User Manual
User’s notes:
Page 2
UltraLab® ULS User Manual
Table of Contents
1.2 WARRANTY STATEMENT ............................................................................................................... 6
2.3 THE PRINCIPLES OF MEASURING DISTANCES BY MEANS OF (AIR) ULTRASOUND ....................................... 8
2.3.2 COMPENSATION WITH AN EXTERNAL TEMPERATURE PROBE .......................................................... 10
2.3.3 COMPENSATION USING A REFERENCE MEASUREMENT ................................................................ 10
DATA TELEGRAM ...................................................................................................................... 13
Page 3
UltraLab® ULS User Manual
For your own safety and for the safe operation of the system, please read the following instructions
carefully PRIOR to operating the system for the first time.
The ULTRALAB® ULS laboratory instrument, as well as the associated ultrasound sensors, represent
state-of-the-art technology and comply with the latest safety regulations.
The manufacturer has made every effort to guarantee safe operation. The user must ensure that
the instrument is set up and installed in such a way that its safe usage is not impaired.
The instruments are factory tested and were delivered in a safe operational condition.
This User Manual contains information and warnings, which must be observed by the user under all
circumstances to ensure safe operation of the instruments.
• The instrument may only be put into operation by authorised persons and only operated by
trained personnel. All users working with this instrument must read the User Manual prior to any
• The user may only perform the repair and maintenance work described. Only the specified parts
are to be used.
Servicing work may only be carried out by authorised service technicians from GENERAL
• All instruments and additional devices used for this purpose must be properly earthed.
• The earth leads must not be interrupted at any point.
• The ULTRALAB® ULS laboratory instrument may only be operated within the specified temperature
range of -20 to +70°C. Otherwise measurement inaccuracies and instrument faults or defects may
The temperature stability of connection cables must match the operating temperature of the
measurement system.
• The sensor should only be connected to the instrument when it is switched off.
• The sensors are to be treated with care and are only to be screwed in hand-tight; otherwise there
is the risk of damage. Sufficient leverage is obtained from the sensor casing itself.
• Avoid electrostatic discharges.
• The ULTRALAB ® ULS laboratory instrument must not come into contact with liquids.
• Never operate the instrument at sites where water may get into the instrument.
• Also take care that the instrument is always operated above the water line of experimental
reservoirs. Protect the instrument against falling into water.
• Isolate all system devices from the mains before undertaking cleaning. Ensure there is no current.
Do not use aggressive cleaning chemicals, liquid cleaners or sprays; only use a damp cloth. Never
bring this or any other cloth into contact with parts of the system that will subsequently conduct
Page 4
UltraLab® ULS User Manual
• Never attempt to open instruments with objects or to insert objects into an instrument. The
voltages existing in the instruments can lead to short-circuits and electric shocks.
• Ensure adequate ventilation when operating the ULTRALAB® ULS. As the instrument has low power
consumption, it requires no additional ventilation under normal conditions. However, the instrument
should never be placed on a source of heat (computer monitors, radiators …).
Only operate the ULTRALAB® ULS at the intended mains voltage of 230 VAC (optionally 110 VAC).
• For safety reasons, the ULTRALAB® ULS is provided with a sealed appliance plug with earth contact
for its mains power. In this context, only appliance cables and plugs with earth contacts may be
used. Operation of the system is prohibited if you do not have this option. Never use an extension
cable without an earth contact.
• The instrument is protected from mains voltage by a blow out fuse in the appliance plug. A finewire fast-blow fuse (G fuse 5 x 20 mm) compliant with IEC with a nominal value of 0.25 A is to be
used as a replacement. Only the specified values may be used. Higher tripping values or bridging
of fuses is not permissible. If the fuse repeatedly blows, the Service Department of GENERAL
ACOUSTICS should be informed, as the cause would need to be resolved.
• We recommend protecting the circuit with FI protective switches to ensure safe operation of your
complete system.
• Take care that power cables are not worn, abraded or otherwise defective. When routing
connecting cables, make certain that the cables do not represent an obstacle or risk of tripping.
• When using extension cables, the total nominal current of all the devices connected must not
exceed the allowable maximum current of the cable. The current ratings of all devices connected
to a single plug should never exceed 15 A, unless the plug is specifically designed for this purpose.
If you are unsure what type of mains power exists in your premises, ask your Safety Officer or an
authorised electrician.
It is imperative to isolate instruments from the mains in the following cases:
• If power cables or plugs are worn or damaged.
• If water or any other liquid has found its way into one of the instruments.
• If the instrument is not working correctly despite following the specified operating instructions.
• If one of the instruments has fallen down or the chassis is damaged.
• If the instrument shows any noticeable departure from normal operation.
• If the sensor connections have become wet.
With the exception of the actions explicitly specified in the manual, you should never attempt your
own repairs on devices belonging to the ULTRALAB® ULS system. Besides the resulting revocation of
warranty coverage, you also risk an electric shock or other injury from the components. All
maintenance work, unless explicitly described in the manual, should only be carried out by
Page 5
UltraLab® ULS User Manual
Warranty statement
Warranty period
GmbH, as manufacturer, will, itself or through its authorised sales
partners, provide end-users with warranty coverage on all GENERAL ACOUSTICS products
purchased as new and unused for a period of 12 months from the date of sale.
Any part, which has been correctly used and is found to be defective as a result of
manufacturing and/or material faults within the above-mentioned warranty period, will either
be repaired or replaced with a new part by GENERAL ACOUSTICS after expert opinion has
been sought. Material and/or labour costs arising as a result will not be charged. All
exchanged parts become the property of GENERAL ACOUSTICS
Conditions for labour rendered under warranty
Instruments delivered must have been operated correctly, unauthorised modifications or
repairs must not have taken place and the bench top instrument must not have been opened.
No warranty claim exists in the following cases
- Parts subject to normal wear
- Damage caused by incorrect maintenance, fitting and addition of non-approved parts and
devices, as well as unauthorised modification of components
- Damage caused by electrolysis
- Damage caused by fire or accident, incorrect usage, misuse or negligence
- Damage/rust/corrosion caused by the entry of water
Explicit or tacit guarantees
These guarantees confer special rights to you, and you may also have other rights,
which differ from country to country or from province to province. Where these
guarantee claims apply, all other explicit or tacit guarantees provided by GENERAL
ACOUSTICS automatically lose their validity, incl. all market access guarantees or
guarantees of fitness for every specific purpose. Conversely, the guarantees thus
arising are limited to the period of this warranty. Neither sales partners nor traders are
authorised to make any other assurances, representation of facts or warranty offers
than those contained in the warranty conditions.
Page 6
UltraLab® ULS User Manual
2. Introduction
Ultrasound measurement of distances in laboratory measurement technology has become
increasingly established in recent years. The advantages gained are quite clear: particularly in
small-scale experimental set-ups, it is imperative to avoid any mechanical intervention that may
affect the experiment, but at the same time, parameters must be measured and evaluated. This
not only applies to laboratory operation and the medium of water. As the distance to an object is
measured by sound propagation time measurement, and not by intensity measurement, as is the
case in optical methods, ultrasound sensors have excellent background suppression. Almost all
materials that reflect sound are reliably detected, irrespective of their colour. Even transparent
materials and thin foils present no problems for our ultrasound sensors. As a result of their high
sensitivity, our sensors are also predestined for the detection of liquid surfaces.
GENERAL ACOUSTICS USS ultrasound sensors permit distance measurement from 30 mm to 3.4 m
and, thanks to high-resolution propagation time measurement, measure with sub-millimetre
resolution. The sensors with a range up to 1.3 m can even resolve the measured distance down to
an impressive 0.18 mm. In addition, the unit features a high measurement rate up to 75Hz, allowing
highly dynamic processes to be recorded.
The sensors measure in dusty air as well as through fine fog. Even thin deposition on the sensor
membrane does not impair the sensor’s function. These characteristics, combined with extremely
slender sound cones (with no secondary cones), make for completely new laboratory applications.
The ULS series of ULTRALAB® sensors are based on an ultrasound pulse echo technique. They have
been developed for temporally and spatially high-resolution measurement of distances in air. The
easy-to-use ULTRALAB® ULS laboratory instrument excels as a consequence of the diverse functions
implemented, making it suitable for use in complex measurement tasks without having to set a
series of parameters.
The measurement object can be, for example, the water surface as a level or the moving water
surface as a wave. This is where the temporally highly resolved distance measurement comes into
its own.
A complex measurement algorithm ensures high measurement accuracy and resolution, as well as
a high degree of data security.
The analogue measurement voltage, proportional to distance, is output at a BNC socket on the
front of the instrument. This facilitates easy integration of the ULS system into an existing data
acquisition system.
System components
The ULTRALAB® ULS instrument system consists of the following components:
- Laboratory apparatus ULTRALAB® ULS Controller
- At least one ultrasound sensor of type USS XXX (XXX specifies the measurement ranges in mm),
and the
- Sensor cables between the sensor and instrument (10m is standard).
Page 7
UltraLab® ULS User Manual
Example: USS20130 is an ultrasound sensor with a measuring range of 200 to 1300mm, i.e. it has a
blind zone below 200 mm from the sensor’s lower edge and a maximum measurement range of
1300 mm from the sensor’s lower edge. That is a net range of 1100 mm or 1.1 m.
The selection of a suitable ultrasound sensor depends on the nature of the surface to be measured,
the maximum measured distance and the required measurement resolution.
The following models are currently available:
Sensor identifier
frequency [kHz]
Response time at
analogue output
resolution [mm]
Reproducibility 1
± 1.00
75 Hz
± 1.00
75 Hz
± 2.00
50 Hz
± 3.0
20 Hz
The principles of measuring distances by means of (air) ultrasound
The ULTRALAB® ULS sends out an acoustic pulse via the ultrasound sensor. The ultrasound pulse
emitted is reflected on the measurement object and is received back as an echo.
A key aspect when it comes to measuring distances is the time required for the transmitted pulse to
cover the distance to the respective measurement object and back. This sound propagation time
is measured by the ULTRALAB® ULS with high resolution.
The measured propagation times are averaged. A tolerance band (expectation range) is set
around the average propagation time. Only measurement values that lie within the expectation
range are admitted for further calculation of the measurement value. The average value is
modified according to changes in distance.
The measured distance is converted to a voltage signal (0-10V) proportional to the distance.
A US sensor can be divided into three functional groups for purposes of illustration:
The ultrasound converter
The evaluation unit
The output (end) stage
The sound source (piezo crystal) is stimulated to oscillate for a brief period. This emits ultrasound
1 Reproducability, or more precisely: accuracy. This implies the accuracy, which remains constant under variable conditions
Page 8
UltraLab® ULS User Manual
1. ultrasound converter
2. evaluation unit
3. output stage
target object
transmitted pulse
echo pulse
transmitted pulse
reception readiness
repetition time
echo pulse
Figure 1: The functionality of an ultrasound-based distance sensor
The sound source is then switched to receive (comparable with a microphone) and the incident US
pulses are evaluated. The propagation time of the sound to a possible target is determined within
the defined measurement window. A voltage value is output, proportional to the measured
The sound propagation time and the measured distance obtained from it will depend to a certain
extent on the following environmental conditions:
Air temperature: The sound propagation time is dependent on air temperature (0.17%/K). Relative
to an air temperature of 20°C, the speed of sound changes by +3.5% at temperatures of approx.
40°C and the measured distance in turn by around 3.5%. These temperature-related changes can
lead to a shift in the localisation of the water surface.
Humidity: The speed of sound increases by a maximum of 2% between dry air and air saturated
with moisture. Consequently, the switching distance changes by a maximum of 2%.
Air pressure: Taking into account all normal atmospheric fluctuations (± 5%), the speed of sound
fluctuates by around 0.6% at a fixed location. The resultant shift in echo propagation time may be
considered negligible.
Air currents: Changes in the speed of sound arising from the continuous changes in current
direction, through changes in air current velocity, as well as the resulting turbulences, is very difficult
to formulate in a general statement. Normally these turbulences can be ignored. For wind speeds
above 50 km/h, changes in the speed and direction of the sound of more than 3% cannot be ruled
out. General guide: Under normal environmental conditions, changes in the speed of sound are
not of any notable significance.
Page 9
UltraLab® ULS User Manual
The distance in metres is measured from the propagation time taking into account the speed of
sound. Compensation should be performed if the speed of sound varies significantly.
Compensation with an integrated temperature probe (standard for USS)
This type of compensation guarantees accurate results for slight variations in environmental
conditions (laboratory). More extensive compensation methods must be applied if conditions are
subject to considerable changes along the measurement path. For this purpose, the integrated
temperature compensation of the sensors must be deactivated by the manufacturer.
Compensation with an external temperature probe
Here temperatures along the measurement path are measured and used for correction. As a
consequence of temperature variations along the measurement path, measurement inaccuracies
can still arise, which are not straightforward to measure. The direct measurement of temperature
can permit very accurate measurement of the speed of sound. The correction of the speed of
sound in air and the associated correction of distance values is, however, only possible offline, i.e.
after a measurement.
Compensation using a reference measurement
The most accurate type of compensation is that of a reference measurement. This can be
necessary for very long measurement paths (several metres) or for extremely variable conditions. In
the case of density variation or stratification of air masses, through which the ultrasound pulse must
penetrate, it is necessary to measure the real speed of sound. An ULTRALAB® ULS measurement
channel can be specially used for such applications as a reference path. The reference sensor
emits sound along a path of maximum possible length, parallel to the measurement channel,
through the same medium/media as the measurement path itself, onto a fixed target at a defined
distance (e.g. 1.0 m when using the USS20130 sensor). The same influences on the speed of sound
are necessarily measured as those on the measuring path itself. If the reference channel is also
recorded, variations in the distance to a fixed object can be concluded from the data from the
change in the speed of sound, and consequently used for highly accurate compensation.
Page 10
UltraLab® ULS User Manual
3. Operating the system Bench top instrument ULS80-D
The bench top instrument has 8 independent channels for easy operation of up to 8 USS series
ultrasound sensors. The sensor cable is connected to the LEMO socket. The output signal can be
received at the BNC socket OUT (0-10V) or at the digital RS 232 data export on the back of the
system. Additional the different channels can be switched on or off at the front panel.
Fig. above: The UltraLab ULS 80D with 8 channels
NOTE! For the not used channels make sure blind plugs are connected.
See plug on right:
Fig. left: The digital RS232 data output at the back of the housing.
Page 11
UltraLab® ULS User Manual
Calculation of the calibration curve
The ultrasound measurement system outputs a voltage proportional to distance of between 0 and
10 V at the BNC output of the bench top instrument. From Figure 2, it may be seen that the
calibration curve is a) a straight line and b) does not pass through the origin. This means that a) the
conversion of distance to voltage is linear and b) an offset has to be added to the distance value
because all ultrasound sensors have a so-called blind zone starting directly at the sensor’s lower
edge (see specifications of the individual sensors). Using an example, it will be shown here how the
calibration curve is calculated with the parameters. It is recommended that the experimental setup be measured beforehand, the expected wave heights determined and then to set the sensors
accordingly. If e.g. wave heights of 10 mm are expected, the sensor should be placed close to the
expected waves but considering the blind zone of the sensor.
hmess = U mess ×
hmax − hmin
+ hmin
U max − U min
Figure 2: The calibration curve
Example from Figure 3: The expected wave or level fluctuations are around 600 mm.
The right sensor for this task is a USS20130 with a measuring range of 200-1300mm below the sensor
lower edge. As environmental disturbances always increase with distance, it should be attempted
to bring the measuring range as close as possible to the sensor. Therefore, a measurement set-up
as shown in the lower figure would be ideal. The window limits are shifted (see 3.2.1) so that the
measuring window near the sensor lies at 200 mm and the measuring window away from the
sensor at 1000 mm below the sensor edge. This results in a measuring range of 1000-200=800 mm,
the value representing the expected max. wave amplitude. The sensor’s analogue output
distributes the output voltage of 10V across the measuring range of 800mm:
Page 12
UltraLab® ULS User Manual
Figure 3: Example measuring setup
Data telegram
The UltraLab® ULS 80D transmits ASCII telegrams via the RS 232 to a PC with a fixed
sample rate of 100 Hz. Any terminal program, e.g. Hyperterminal, can be used to view
and log the data externally. The telegrams contain eight numbers separated by “;”
characters. The single characters show the output in mV from 0000-1000 mV Each
number represents a channel from left to right channel 1 to 8:
Page 13
UltraLab® ULS User Manual
CE conformity statement
Technical specifications
Instrument model
Measuring range
USSxx, IP 65, M30x1.5, with temperature compensation, nickel plated brass
tube (optionally stainless steel)
freely adjustable between the blind zone (from 30 mm to 350 mm) and the
detection range limit (from 250 mm to 3400 mm)
up to 1mm (under stable environmental conditions)
(dependent on sensor model)
from 0.18 mm to 1 mm (dependent on sensor model)
from 20 Hz to 75 Hz (dependent on sensor model)
Voltage output
BNC socket: 0–10 V, Digital RS 232 data export at 100 Hz
Power supply
230 VAC, 250 mA (110 VAC optional)
approx. 250 / 90 / 190 mm width / height / depth IP 50
Temperature range -20…+70°C
Delivery package
laboratory instrument ULS-80D, ultrasound sensor USSxx, 10 m sensor cable,
user manual, mains cable
Page 14