THE HYBRID WATER PURIFIER USER MANUAL

THE HYBRID WATER PURIFIER
USER MANUAL
Congratulations on the
purchase of your water purifier
F-FWEG1-M-A-NT-**-***
Warning: Boil the water
should the purification unit fail
DECLARATION
Waterlogic International Ltd
1. If any abnormal case occurs, firstly unplug
the appliance.
2. T
his appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
3. Children should be supervised to ensure
that they do not play with the appliance.
4. This appliance can be used by children
aged from 8 years and above if they have
been given supervision or instruction
concerning use of the appliance in a safe
way and if they understand the hazards
involved. Cleaning and user maintenance
shall not be made by children unless they
are older than 8 and supervised. Keep the
appliance and its cord out of reach of
children aged less than 8 years.
5. A
ppliances can be used by persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved.
6. Children must not play with the appliance.
7. If the supply cord or the detachable cord
sets are damaged, it must be replaced by
the manufacturer, its service agent or
similarly qualified persons in order to avoid
a hazard.
8. WARNING: fill with potable water only.
9. The appliance is to be supplied through a
residual current device (RCD) having a
rated residual operating current not
exceeding 30mA.
10. T
his appliance is intended to be used in
household and similar applications such
as
– staff kitchen areas in shops, offices
and other working environments;
– farm houses and by clients in hotels,
motels and other residential type
environments;
– bed and breakfast type environments;
– catering and similar non-retail
applications.
11. This appliance contains a UV-C emitter
(UV lamp)
12. Unintended use of the appliance or
damage to the housing may result in the
escape of dangerous UV-C radiation.
UV-C radiation may, even in little doses,
cause harm to the eyes and skin.
13. Appliances that are obviously damaged
must not be operated.
14. Read the maintenance instructions before
opening the appliance.
15. The appliance must be disconnected from
the supply before replacing the UV lamp.
16. The UV lamp must be replaced at 12
month intervals or when necessary.
If the unit is placed in a high use area,
the UV lamp will need to be replaced
more frequently. The quartz spiral can
be cleaned by using an ultrasonic bath
if needed.
17. WARNING: Do not operate the UV lamp
when it is removed from the appliance
enclosure.
3
IMPORTANT
CAUTIONS
To enjoy the reassurance of delicious, refreshing, healthy and hygienic drinking water,
please follow the instructions contained in this document. Please retain these instructions
for future reference in a safe and convenient place.
1. Only trained competent technicians should
carry out repairs on the appliance
2. Packing materials could present a trip
hazard. Keep them off the floor and out of
reach of infants and small children
onnecter uniquement à un circuit protégé
C
par une mise à la un défaut à la terre de
circuit (GFCI)
7. WARNING – Improper connection of
the appliance-grounding conductor
can result in a risk of electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether
the appliance is properly grounded.
Do not modify the plug provided with
the appliance; if it will not fit the outlet,
have a proper outlet installed by a
qualified technician
•This appliance is for use with potable drinking
water only. Never use this appliance with
unknown or unsafe sources
•Read all instructions contained in
this user manual prior to using
this appliance
•Check if the voltage indicated on the
appliance corresponds to the local mains
voltage before you connect the appliance
•When removing the water reservoir from
the appliance, place one hand on top of the
appliance securing it while using your other
hand to remove the reservoir
3. A
void the power plug and cord contacting
water or moisture. Should this happen,
unplug the lead from the power source
and discontinue using the appliance until
deemed safe to do so
•Do not allow children to use the appliance
without supervision
•Systems certified for cyst reduction may be
used on disinfected waters that may contain
filterable cyst
4. Do not handle or move the appliance when
the reservoir contains water
•Never leave the appliance unattended when
water is being dispensed
•The system and installation shall comply
with applicable state and local regulations
•Never use the appliance if there is any visible
damage to the appliance or the power cord
•The system must be supplied with cold
or ambient water
•The reservoir may be stored in the fridge if
you would like to dispense cold water from
the appliance
DECLARATION
•Do not use this appliance if the mains cord,
plug or other parts are damaged
•Unplug the appliance before removing any
part of the appliance for servicing
•This appliance is for indoor use only
•Never immerse the appliance in water
or spray any liquid onto the outside of
the appliance
•Do not overfill the reservoir
•When re-inserting any screws
make sure that they are
hand tightened only
•Only use authorised parts from the
manufacturer to repair and service
the unit
•Only use Waterlogic UV lamps and filters
with the appliance, failure to do so will
void the warranty
•When the appliance has not been
used for 3 hours or is idle, the UV
lamp will turn on for 60 seconds at
3 hour intervals
The UV lamp in our appliance conforms to the
applicable provisions of the Code of Federal
Regulations (CFR) requirements including, Title 21,
Chapter 1, Subchapter J, Radiological Health
DÉCLARATION
La lampe UV dans notre appareil est conforme
aux dispositions applicables du Code of Federal
Regulations (CFR), y compris à ses exigences
du titre 21, chapitre 1,
sous-chapitre J «Radiological Health»
Power Supply: 220-240 Volt / 50Hz & 120 Volt / 60Hz
Power consumption: 0.07 Kwh
Rated service flow: ≥1.0lpm
Operating Temperature: 2˚c - 32˚c
Reservoir capacity: 1.5 Liters
6. Connect only to a circuit that is protected
by a ground-fault circuit-interrupter (GFCI)
5. GROUNDING INSTRUCTIONS – This
appliance must be grounded. In the event
of a malfunction or breakdown, grounding
will reduce the risk of electric shock by
providing a path of least resistance for
electric current. This appliance is equipped
with a cord having an appliance-grounding
conductor and a grounding plug.
The plug must be plugged into an
appropriate outlet that is installed and
grounded in accordance with all local
codes and ordinances
MISE A LA TERRE – Cet appareil doit être
mis à la terre. En cas de dysfonctionnement
ou de panne, la terre réduira le risque de
choc électrique en fournissant un chemin
de moindre résistance pour le courant
électrique. Cet appareil est équipé d’un
cordon muni d’un conducteur appareil à la
terre et une fiche de terre. La fiche doit être
branchée dans une prise appropriée qui est
installée et mise à la terre conformément à
tous les codes et règlements locaux
A
VERTISSEMENT – Un mauvais
raccordement du conducteur de mise
à la terre de l’appareil peut entraîner un
risque de choc électrique. Vérifier avec
un électricien qualifié ou un technicien
agréée représentant de service si vous
avez des doutes quant à la mise à la terre
de l’appareil est correctement mis à la
terre. Ne pas modifier la fiche fournie avec
l’appareil ; si elle n’entre pas dans la prise,
faites installer une prise adéquate par un
technicien qualifié
8. W
arning – Isolate power supply before
removing cover
9. T
his Class A system conforms to NSF
Standard 55 and P231 for the disinfection
of micro biologically contaminated
water that meets all other public health
standards. The system is not intended to
convert wastewater or raw sewage into
drinking water. The system is intended to
be installed on visually clear water
•Make sure the appliance is placed on
a flat, level, dry and secure surface
5
1. BOX CONTENTS
1.1Remove the HYBRID from the box. To
avoid damaging the appliance DO NOT
use any sharp object to open the box
2. SET-UP GUIDE
A
HYBRID UNIT
IMPORTANT
B
RESERVOIR LID
1.2Please check the contents of the box and
make sure that all items are present
C
RESERVOIR
2.1Check the unit for any damage, if the
appliance is damaged then please
return to the place of purchase
D
DISPENSING BUTTON
1.3The UV lamp and filter are pre-installed
and ready to use.
E
FAUCET
F
DRIP TRAY
2.2Remove the protective cover from the
end of the Firewall spiral
D
B
2.3Insert the plug into the mains socket.
When the mains power is switched
on the appliance will automatically go
through a self check/test and once this
is complete the button will turn blue
E
A
C
F
2.4Remove the water reservoir from the
main body of the appliance and remove
the lid from the reservoir
If any of the items are missing please contact customer service
7
2.5Rinse the reservoir and then fill the
reservoir from a potable water source.
Do not overfill the reservoir. Re-fit the
reservoir cover
2.7Place a glass or large container under the
dispense area and touch the dispense button
to operate the unit, and touch again to stop the
appliance. Allow water to run through the unit
until the reservoir has been emptied. Refer to
section 5 in this manual for the button functions
Note: Do not consume the water
until step 2.8 has been completed.
The first 3-5 litres of water dispensed may
contain some fine, black carbon particles.
Carbon is a natural, organic material made
from coconut shell, and is harmless to your
health. Clear water should be noticed after
flushing through 3 to 5 litres of water (2 to 3
full reservoirs). Do not allow the water level in
the reservoir to drop below the minimum fill
line, as when the reservoir is completely empty
the pump will begin to suck in air and make
bubbling noises.
2.6 0Re-fit the reservoir to the appliance
making sure it is firmly fitted
Note: Should the machine fail or any of the
components fail, and the water in your area is
particularly hard, we recommend purchasing
a Waterlogic de-scaling kit and de-scaling
the unit
2.8Repeat steps 2.4-2.7 three to four
times (3x - 4x). This will flush the carbon
from the new filter
x3-4
2.9Once step 2.8 has been completed
you can drink purified, healthy and safe
water from your appliance
During the first week of use and after
every filter change you may notice water
dripping out of the dispensing-nozzle
for several seconds after the unit has
stopped dispensing. This is normal,
and will stop after several days of use.
Note: For a cold refreshing drink the
reservoir may be stored full of water
in the fridge
9
3. UV BULB AND FILTER REPLACEMENT
THIS PRODUCT IS A HIGH PERFORMANCE WATER PURIFIER, KEEPING IT IN GOOD
WORKING ORDER WILL PROVIDE THE REASSURANCE OF TRULY GREAT DRINKING WATER
3.3 Remove the top cover from the unit by
slightly pushing it back and then lifting it up
PLEASE READ AND NOTE SECTION 6 “INDICATION & WARNING ICONS”
IMPORTANT - UNPLUG THE APPLIANCE
FROM THE MAINS BEFORE REPLACING
THE UV LAMP OR FILTER
SHOULD THE MACHINE FAIL OR
ANY OF THE COMPONENTS FAIL,
AND THE WATER IN YOUR AREA
IS PARTICULARLY HARD, WE
RECOMMEND PURCHASING A
WATERLOGIC DE-SCALING KIT
AND DE-SCALING THE UNIT
•The UV Bulb and Filter must be
replaced every 12 months to ensure
that your appliance is dispensing the
highest quality drinking water.
Replacement Parts:
Please make sure you use only original
Waterlogic replacement parts. If you
are not sure which replacement parts
to use, please consult with your local
Waterlogic retailer or distributor
3.4 Disconnect the UV lamp connector by
holding it and pressing in the clip on the
connector and pulling it up
3.1Remove the water reservoir from the
main body of the appliance. This can
be cleaned with a light solution of
dishwashing liquid. Never use abrasive
chemicals or materials to clean the
reservoir as this could scratch and
deface the product
3.5To remove the UV lamp firmly pull it up
and out. Do not pull the lamp out at an
angle as it may break or damage the
internal parts of the appliance
3.2Remove the two screws that hold the
top cover in place. You will need to use
a screwdriver to carry out step 3.2
Note: The UV lamp must be disposed
of correctly and must not be disposed
of with normal household waste
11
3.6Insert the new UV lamp while holding the
white end caps only. Insert the UV lamp
as shown in the illustration and push it all
the way down until it cannot go
any further
3.9Fit the new filter assembly into the
appliance as follows:
1. Insert the filter assembly back into
its cradle, aligning the two male spigots
with the female holes in the cradle
CAUTION
:- Do not use force when removing and
inserting the UV lamp as you may
damage internal parts
:- Do not touch the UV lamp glass
surface with your fingers as this
will affect the performance of the
UV lamp
2. Push firmly until the filter sits snugly
and is flush inside the cradle and with
the cradle top surface
2.
3. Lock the filter by closing the locking
lever until it ‘clicks’ into place
4. Rotate the red rotating lever back into
the LOCK position
1.
3.7Re-connect the UV lamp connector
making sure the connectors are lined
up correctly as they will only fit together
when correctly aligned
3.
3.8To remove the Filter, do the following:
1. Rotate the red rotating lever so that it is parallel
with the side panel
2. Insert your finger into the round hole of the
lever, and pull the lever up to the
vertical position
3. Pull the lever straight up to remove
the Filter assembly (Slight force may
be required. Support the unit with
your other hand while pulling the
filter out).
Note: Dispose of the filter
following your local guidelines
1.
2.
3.
13
4. BUTTON FUNCTIONS
3.10Re-fit the top cover, making sure the
front is attached first. If the top cover
is not fitted correctly the unit will
not switch on
4.1When the appliance is in standby mode
the button will be blue but when it is
touched it will turn green and water will
be dispensed
Hint: Fit the top cover making sure the
front is pushed in place first and then
push the back end with the screws
down to give a snug fit
Note: If the button is not touched within
2 minutes of being activated then it will
automatically stop the flow of water and
turn the pump off.
3.11Re-fit the two screws that hold
the lid down using a screwdriver.
Caution: The screws should be hand
tightened, do not over tighten
Insert the plug into the mains socket.
3.12Press and hold the dispense button for
10 seconds until you hear a beep as this
will rest the filter timer
Note: Place a cup or container under
the dispense area before carrying out
step 3.12
4.2 Touch to STOP dispensing water.
When you touch the button to stop
water being dispensed the button will
change colour from green to blue
Note: After one minute the product is
in a stand-by mode it goes in an energy
saving mode as the UV is off; when the
product is in this condition, there will
be a 2 second delay before the water is
dispensed after the dispense button is
touched so as to activate the UV lamp
and purify the water.
3.13 The filter now needs to be flushed,
follow step 2.3 through to 2.8
15
5. INDICATION AND WARNING ICONS
6. TROUBLESHOOTING
Your product has been designed and internationally certified to the highest standards of water
purification, and guarantees at all times, to dispense the purest and cleanest water. The self
monitoring system will warn you of any potential risks, by way of 3 possible alarms.
If there is no water being dispensed:
•
• Check that the unit is plugged in and
switched on at the mains
wall socket
Should the appliance be faulty please either
return the product in its original packaging
with proof of purchase or contact the local
customer service centre.
5.1
Once the Filter has reached 95% of
its life, the Filter icon will flash as a
reminder, and continue to flash until
the filter has been replaced as per 5.2
below. During this time, your machine
will continue to dispense water, until 5.2
below has been reached
• Check that the reservoir is
fitted correctly
• Check that there is water in
the reservoir
Make sure the button is blue
Should there be no response from the button
remove the power cord and wait 10 seconds
before plugging it back in. This will reset
the appliance.
• Make sure that the top cover is
fitted correctly
5.2 After a 12 month period, both the UV
Bulb and Filter must be replaced to
ensure optimal water purification. Both
the UV Icon and Filter Icon will alarm 20
times and flash alternately. When this
occurs, no water will be dispensed, until
the Filter and UV Bulb have both been
replaced and the machine reset (to do
this you will need to follow steps 3.1
to 3.13 )
5.3 In the unlikely event that the UV bulb
should fail the UV icon will flash and
alarm 20 times.
7. CLEANING
It is recommended that you maintain your appliance by cleaning it on a regular basis.
The appliance can be cleaned using a damp lint free cloth. Never use any alcohol or alcohol
based chemicals or abrasive materials on any part of the product.
Should the machine fail or any of the components fail, and the water in your area is particularly
hard, we recommend purchasing a Waterlogic de-scaling kit and de-scaling the unit.
8. STORAGE
No water will be dispensed until steps
3.1 to 3.7 and steps 3.10, 3.11
are completed
Never store the appliance with water in the reservoir and always store it the correct way up in a
dry environment. If the unit has not been used for more than 3 months it is recommended that
the filter be replaced before the appliance is used.
17
9. SAFETY
•Do not touch or look directly into
the faucet
•Do not handle or lift the appliance by
holding the reservoir
•Only authorised trained technicians may
carry out repairs on this appliance
•The user may only replace the filter and
UV lamp
•The filter and UV lamp must be replaced
every 12 months.
•Never use any chemicals or abrasive
materials on any part of the product
•Should a fault occur on the appliance
always unplug it from the mains
power supply
•If the power lead is damaged in any way
it must be replaced by an authorised
dealer or qualified person
•This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety
•Children should be supervised
to ensure that they do not play
with the appliance
10. CERTIFICATION
The appliance has attained and complies with the following certifications and directives:
CE, NSF 42 & 53, NSF 55a, NSF P231, RoHS, REACH
11. DISPOSAL
Do not dispose of the appliance with normal
household waste, hand it in at an official
collection point for recycling. By doing this
you are doing your bit for the environment.
WEEE compliance
Correct Disposal of this product
This marking indicates that this product should not be
disposed with other household wastes throughout the EU.
To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the
return and collection systems or contact the retailer where
the product was purchased. They can take this product for
environmental safe recycling.
18
Manufactured by Qingdao Waterlogic Manufacturing Co., Ltd
No 10 Jinling Road, Jinling Industrial Zone, Chengyang District, Qingdao, 266111, Shandong, P.R. CHINA
TEL: +86-532-87909132
25042014v19