22X Speed dome User Manual

22X Speed dome User Manual
RL-CS-6830C-A
RL-CS-6830C-B
Contents
1. Product Overview...........................................................................................................................1
2. Technical Parameters......................................................................................................................2
3. Setting, Installation and Connection…..........................................................................................3
3.1 Settings of Speed Dome Camera ID, Transfer Rate and Communication Protocol..........… 3
3.1.1 Settings of Speed Dome Camera ID…………………………………………........… 4
3.1.2 Settings of Speed Dome Camera Communication Protocol…………………….........4
3.1.3 Settings of Speed Dome Camera Transfer Rate……………………………….......… 5
3.2 Installation and Connection…................................................................................................ 6
3.2.1 Dome Camera Wall-mounted Bracket Installation ….................................................6
3.2.2 Dome Camera Ceiling-mounted Bracket Installation………………………….……10
4. Dome Camera is controlled by Keyboard…................................................................................12
4.0 Select the Camera ID to be controlled…………………………………...............................12
4.1 Set and Call Preset Position…………………………………………………………...........13
4.1.1 Set Preset Position……………………………………………………………….............13
4.1.2 Call Preset Position……………………………………………………………...............13
4.1.3 Clear Preset Position……………………………………………………….....................14
4.2 Dome Camera Cruising Function…..........................................................................................14
4.2.1 Set Cursing Track………………………………………………………………..............14
4.2.2 Run Cursing Track………………………………………………………………............15
4.2.3 Stop Cursing Track………………………………………………………………...........16
4.3 Auto Scanning…………………………………………………………………………….......16
4.3.1 Scanning between Two Spots………………………………………………………......16
4.3.2 360° Scanning……………………………………………………………………...........16
4.3.3 Auto Scanning by Clicking [PRESET] + [ENTER] ………………………………........16
4.4 Home Place…………………………………………………………………………………......0
5. Other Functions…………………………………………………………………………….........0
5.1 Object Tracking…………………………………………………………………………......0
5.2 Camera Control……………………………………………………………………………..0
5.2.1 Zoom Control…………………………………………………………………….......0
5.2.2 Focusing Control…………………………………………………………………..…0
5.2.3 Aperture Control…………………………………………………………………..….0
5.2.4 Auto BLC………………………………………………………………………..……0
5.2.5 Auto WEB..............................................................................................................…...0
6. Camera 【OSD】Menu Setup.........................................................................................................0
7. Troubleshooting.............................................................................................................................0
8. Appendix
Ⅰ Lightning and Surge Protection…………………………………………………….............… 26
Ⅱ Cleanness of Transparent Cover…………………………………………………………........ 27
Ⅲ General Knowledge of RS485......................................................................................…..........27
Ⅳ Relational Table of 24V AC Line Diameter and Transmission Distance……………… ...........29
Ⅴ Domestic and Overseas guage table……………………………............................................... 30
Ⅵ Address Coding table………………………………………………………………..................31
Safety Precaution
1. Before attempting to operate this product, please read these instructions carefully.
2.
In order to avoid damaging this product, please choose the power correctly.
3. The inner elements of the Dome Camera are precise optic, electronic and
mechanical parts, so wrong operations, such as heavy load and strong vibration
should be avoided during transportation and installation. Otherwise, the product
could be damaged.
4. The Camera should not be put on unsteady desks and brackets.
5. Avoid liquid or other things penetrating into the camera, or the camera could be
damaged.
6. To avoid affecting the usage of the Dome Camera, please do not dismount its
inner elements. There are no user serviceable parts inside.
7. Do abide by electrical safety standards, and use self-contained specialized power
sources. Its RS-485 and Video Signal adopt TVS-level anti-thunder, so it can
effectively avoid the damage caused by various pulse signals, such as
instantaneous thunder below 1500w, surge, etc. RS-485 and Video Signal should
be kept away from high voltage equipment or cable during transmission. Please
take actions to prevent lightning strike and surge when necessary.
8. No matter the camera is in use or not, it should never be exposed to the sun or
other bright objects. Otherwise, it may cause permanent damage to Camera CCD.
9. When the machine has broken down, please do not make any repairing operations
unless you refer to instructions to detect faults first. If no reasons can be found,
please ask professionals to conduct the maintenance work. And the professional
maintenance persons should be authorized by our company.
10. Do not disassemble, or modify the system.
1. Product Overview
Intelligent Dome Camera is a high-tech surveillance product combined
high-performance and high-speed focused Integrated monitoring system, universal
variable PTZ, multifunctional decoder, universal character generator, CPU as well as
memory chip into one. By doing so, this kind of camera not only has the functions of
rapid location and continuous follow-up scanning in a row, but also achieves the real
all-round and no blind spot monitoring. Besides, it can automatically adapt to the
environment and the objectives that are changing in terms of distance. This camera
adopts full digital control system, and its design is quite exquisite and simple,
minimizing the connections between system components to improve the reliability of
the system to the greatest extent, and it is very convenient for installation and
maintenance. Moreover, it uses precision stepping motor to drive, achieving the
effects of stable operation, rapid response and accurate positioning, and the accuracy
of positioning can reach ±0.1°. In addition, it has the intelligent functions of around
scanning, pattern scanning, privacy dodging, and motion detection, alarm uploading
images to the appointed mailbox or FTP server. This camera is applied to large area,
and moving objects monitoring in every walk of life, such as intelligent mansion,
banks, urban streets, electricity departments, airports, stations and so on.
2. Technical Parameters
2.1 7″ Speed Dome Camera Technical Parameters:
Model
Power Supply
RL-CS-6830C-A
AC24V±5%
Operation Temperature
–20℃~+60℃
Humidity
≤95% no dew
Power Consumption
Communication Mode
Baud Rate
Horizontal Rotate Speed
Horizontal Rotate Range
Pitching Range
Auto Flip Function
20W
RS485
2400/4800/9600/19200 bps
1°~180°(1~64shift)
1°~300°(1~64shift)
360°rotation
90°
Auto Flip 180°when Vertical 90°
Auto Control Focus
Speed
Two Spots Scan
Two Spots Scan Speed
Auto adjust according to focus change
At random
1~8 optional
Two Spots Scan Dwelling
Time
1~60sec.optional
Preset Position Number
128
Speed to Preset Positions
1~8 optional
Every Preset Position
Dwelling Time
1~60sec.optional
Cursing Group
6
Cursing Spots in every
Group
16
2.2 Speed Dome Camera Lens’ Technical Parameters (built in the 22X D/N high
speed focus camera)
Image Sensor
1/4″SONY SUPER HAD CCD
Signal System
NTSC/PAL
Synchronizing System
Scanning Mode
Horizontal Resolution
Min. Illumination
Iris
Focus Mode
Focus Sensitivity
Focus Rate
Focus
Video Angel
Internal/External
2:1 interlacing scan
480TVL
0.1Lux
Auto/Manual
Auto/Interval/Trigger/Manual
High/Medium/Low
22X
3.9~85.8mm
wide-angle 65°/narrow-angle2.7°(22X)
BLC
Area detection BLC
AWB
auto-speedy/manual/indoor/fluorescence light/outdoor
AGC
auto
S/N Ratio
video Output
>52dB
1.0±0.2Vpp
3. Settings, Installation and Connection
3.1 Settings of Speed Dome Camera ID, Transfer Rate and Communication
Protocol
Before installing the Dome Camera, please confirm the communication protocol,
baud rate and local address code of the control host, and then the DIP-switch should
be set to be in complete accordance with that in control system. Its corresponding
DIP-switch settings and connecting line can be seen in picture 1:
3.1.1 Settings of Speed Dome Camera ID
Before the Intelligent Dome Camera is used, its address code should be firstly set
by (SW1) 8 bit code switch on PCB board with binary system 8421 code. The largest
encode address is 255, and the number 1 indicates “on”, while the number “0” means
“off”. (As it shown in picture 2): Set each Dome Camera ID code and the keyboard
input of corresponding ID on LCD:
As shown in the picture above: The first switch is in the “ON” status,
button on the control keyboard, and then input number “1”. Then click “Enter”
again, which indicates that the ID is set as NO.1 control ID. The Dome Camera
ID can be set as 001. Other addresses could be set in the same manner.
◆ The new settings will not be effective until the Dome Camera reboots.
3.1.2 Settings of Speed Dome Camera Communication Protocol
No.1、2、3、4 on PCB board SW2 is the communication protocol setting. As it is
shown in picture 3:
◆The setting of speed dome camera communication protocol will not be effective
until the computer reboots.
3.1 .3 Settings of Speed Dome Camera Transfer Rate
The position of 4 and 5 of the SW2 on the PCB board are used for Baud rate
settings. The default value is 2400BIT/S. The Baud rate is 2400BIT/S, 4800BIT/S,
9600BIT/S, 19200BIT/S optional.
◆The setting of speed dome camera communication protocol do not work until
computer reboots.
3.2 Installation and Connection
1. The installation and connection of the Mini Intelligent Dome Camera should be
implemented under local provisions by people who own the technical qualifications of
CCTV system installation.
2. Please refer to the silk print on PCB and the installation manual for the detailed
information of the connection of each line.
3. Avoid direct touch to the lower cover of the dome to prevent scratches and the loss
of image quality, for the cover is a high-level optical instrument.
4. To ensure the image quality, the lower cover of the dome camera should be cleaned
periodically. When cleaning, take the lower cover down by holding the outer ring
carefully, avoiding direct touch; the acidic sweat on one’s finger might corrode the
coating of the cover. And the scratches made by hard objects might also result in a
blurry image. Please use a tender dry cloth or other substitutes to clean both the inner
and outer side of the cover. If the dirt is hard to clean, a neutral detergent could be
used; any cleanser which is for luxury furniture can be used for the lower cover.
3.2.1 Dome Camera Wall-mounted Bracket Installation
Wall-mounted Bracket Installation
Note: The ceiling which to be installed on should be solid and with no
delaminating. The bearing capacity of the installation location should be able to afford
at least five times of the total weight of the Dome, frame and pedestal, in order to
avoid image jitter caused by unstable installation.
a. When installing on the wall, put up a positioning on it first.
b. Use percussion drill to drill holes according to the marks; install four expansion
bolts (M8).
c. Put the cable through the frame holes, and set aside enough cable for connection.
d. Fasten the frame to the wall by using four M8 nuts and four spacers, and then
install the dome.
Outer Wire Connection
Connect the BNC video interface of Dome Camera to the arranged video cable;
connect the power cord to the arranged power cord (AC24V). RS485 control wire is
connected to RS485 control wire layer out.
◆ Ensure that the positive and negative polarity of RS485 is properly connected.
“A” represents positive pole, while “B” negative pole.
If RS485 is wrongly connected, it could not control the Dome Camera.
a. Check the polarity of the plug and socket, and the connection of cable, then
power on.
b. When the self-checking starts, the Dome will turn 360°horizontally and then
90°vertically for the testing of the camera and the electrical and mechanical structure
of the Dome, and turn back to the initial position by the resetting program. When the
Dome totally stops, the self-checking finishes and it is ready to be under control.
Down Cover Installation
a. Wipe the dust and dirty marks on the cover with tender lint to avoid scratching the
cover.
b. Make the three screw holes of the bottom cover aim at the outer cover screw holes,
and then fasten them with three screws (M3).
3.2.2 Dome Camera Ceiling-mounted Bracket Installation
Ceiling-mounted Bracket Installation
Note: The ceiling which to be installed on should be solid and with no
delaminating. The bearing capacity of the installation location should be able to
afford at least five times of the total weight of the Dome, frame and pedestal, in
order to avoid image jitter caused by unstable installation.
a. When installing on the wall, put up a positioning on it first.
b. Use percussion drill to drill holes according to the marks; install four expansion
bolts (M8).
c. Put the cable through the frame holes, and set aside enough cable for connection.
d. Fasten the frame to the wall by using four M8 nuts and four spacers, and then
install the dome.
4. Dome Camera is controlled by keyboard
Intelligent control and all functions can be achieved by controlling the Dome
Camera with keyboard. Meanwhile, there are different operating methods for different
control system platforms. Generally speaking, operating methods should be based on
the manual offered by system manufacturer. Sometimes there may be some special
requirements and operation methods. In this case, please feel free to contact
distributors to get the useful information. (We advise you to control the Dome Camera
with original keyboard to achieve optimal performance.)
Take the original keyboard of the Dome Camera manufacturer as an example.
The agreement for Keyboard control is (PELCO-D、PELCO-P) .
4.0 Select the Dome Camera ID to be controlled
【CAM】+【N】+【Enter】(N: Camera Number, range 0~255)
First, click the “CAM” button,then input the number N (address) of the Dome
Camera to be controlled, and then click “Enter”. When the number N is consistent
with the Camera ID, the Dome Camera is ready to be controlled.
For example: Control No.2 Dome Camera
a. Click “CAM”. (The screen shows as picture 1)
b. Input “2”
c. Click “Enter”. (The screen shows as picture 2)
Picture 1
Picture 2
4.1 Set and Call Preset Position
Preset function is that the position parameters of horizontal angle, vertical angle,
and lens focus are stored into Dome Camera with the number (1-128). When needed,
these parameters can be transferred to adjust the Dome Camera to a fixed position.
Users can conveniently store and call the preset positions by controlling keyboard.
This kind of camera support 128 preset positions.
4.1.1 Set Preset Position: [PRESET] + [N] + [Enter] (N: Preset Number,
range1~128)
After the Dome Camera is adjusted to the best position through keyboard
(including the selection of location、 Camera zoom、focus、and Iris), click the
“PRESET”, and then type the number N of representing this preset position. Finally
click “Enter”.
For example: Set No.2 preset position
a. Adjust camera to a required position by moving lever, and adjust the lens’s zoom
b. Click “PRESET” (Picture 3)
c. Input 2 (Picture 4)
d. Click “Enter”
Picture 3
Picture 4
◆ When set preset positions for distant objects, you can focus the image manually.
That is to say, when adjust lens at a distance, you can adjust and store the best images
by controlling “FAR” / “NEAR” buttons on the keyboard. By doing so, image
blurring could be avoided.
4.1.2 Call Preset Position: [CALL] + [N] +ENTER] (N: the number of preset
position)
The function of calling preset positions is adjusting camera to the previous
position. Click “CALL “firstly, and then input the preset position number to be called.
Lastly, click “ENTER”. At this time, the camera is back to the original position.
For example: Call No.2 preset position
a. Click “CALL” button. (Refer to the picture 5)
b. Input No. 2 ( Refer to the picture 6)
c. Click “ENTER” button.
Picture 5
Picture 6
4.1.3 Clear Preset Position: [PRESET] + [N] + [OFF] (N: the number of preset
position)
Clearing preset position is to delete the stored preset location in the Dome Camera.
For example: Clear No.2 preset position.
a. Click “PRESET” button. (Refer to the picture 7)
b. Input No.2. (Refer to the picture 8)
c. Click “OFF” button.
Picture 7
Picture 8
4.2 Dome Camera Cruising Function
Auto cruising is an important feature for Dome Camera. This function can
arrange preset positions to the cruising queue in a required order. Under an external
command, the Dome Camera can automatically visit back and forth at a specified
interval time in sequence. Altogether 8 cruise tracks can be set, and each track
involves 16 preset positions.
4.2.1 Set Cruising Track: Enter and edit cruise tracks.
Set the cruise tracks of Dome Camera with keyboard. Click “SHOT” button
firstly, then input the number of cruise track. Next, click “ON” button to enter a
cruising tracks setting state. After that, click “TELE” button enter the next step, and if
you click the “WIDE” button, you can go back to the last step. Each track involving
16 preset positions, and the running speed and dwelling time upon each point can be
edited by controlling “TELE/WIDE “buttons.
For example: The first preset position in the first cruise track is set as the No.1
preset position. Its running speed is Level 5 and dwelling time is 3 seconds.
a. Click “SHOT” button.( Refer to the picture 9)
b. Press 1 on the number pad to set cruise track.
c. Click “ON” button is set to enter the track. (Refer to the picture 10)
Picture 9
Picture 10
d. Click “TELE” button.
e. Press 1 on the number pad to set preset position 1. (Refer to the picture 11)
f. Click “TELE” button.
g. Press 5 on the number pad to set running speed. (Refer to the picture 12)
Picture 11
Picture12
h. Click “TELE” button.
i.
Press 3 on the number pad to set dwelling time. (Picture 13)
j.
Click “TELE” button to set the second preset position. (Picture 14)
Picture13
Picture14
NOTE: Click “OFF” button to save settings and back to last step after the preset
positions settings are finished. If you rotate the level or press other buttons, the
settings could not be saved.
● Altogether 6 cruise tracks can be set. Each track involving 16 preset
locations.( Preset position at random is 1—128).
● 1~60 secs dwelling time for each preset location can be set, and level 1~8 preset
location speed to each point can be set as well.
4.2.2 Run Cursing Track: [SHOT] + [N] + [Enter] (N: the number of cruise track,
1~6)
For example: running the first cruise track.
a.
Click “SHOT” button.
b.
Press 1 on the number pad to activate the first cruise track..
c.
Click “Enter” button.
4.2.3 Stop Cruising Track: [SHOT] + [OFF]/ Use level
4.3 Auto scanning (2-spot scanning, 360° scanning)
The Auto Scanning function enables that the Dome Camera can scan randomly
between 2 selected locations, or can do 360° scanning. While scanning, it will
automatically run with matched speed according to the lens’ focal length.
4.3.1 Scanning between Two Spots
a. Move to the start point (point A) by using level. Then click “PRESET” button, and
input 101 on the number pad. Finally click “ENTER” button.
b. Move to the end point (point B) by using level. Then click “CALL” button. After
that, input 101 on the number pad. At last, click “ENTER” button.
c. Click “CALL” button. Then input 103 on the number pad. At last, click “ENTER”
button.
d. If you want to stop scanning, please use the level.
4.3.2 360° Scanning: [CALL] + [106] + [Enter]
a. Click “CALL” button.
b. Input 106
c. Click “ENTER” button.
d. If you want to stop scanning, please use the level.
4.3.3 Auto Scanning by clicking [PRESET] + [ENTER]
Click [PRESET] + [102] + [ENTER] to scan automatically at a low speed.
Click [CALL] + [102] + [ENTER] to scan automatically at an intermediate
speed.
Click [PRESET] + [103] + [ENTER] to scan automatically at a high speed.
Note: 2-spot scanning can be set in the same way.
4.4 Home Place
The Home Place function is that the Dome Camera will return to No.1 preset
location automatically when no operation is done in a period of time. The Home Place
function of Dome Camera can be activated through keyboard.
4.4.1 Start Home Place Function: [PRESET] + [107] + [ENTER]
a. Click “CALL” button (The screen shows as picture 15)
b. Input 107 on the number pad to activate the mode. (Picture 16)
c. Click “ENTER” button.
Picture 15
Picture16
4.4.2 Stop Home Place Function: [CALL] + [107] + [ENTER]
a. Click “CALL” button (Picture 17)
b. Input 107 on the number pad to activate the mode. (Picture 18)
c. Click “ENTER” button
Picture17
Picture18
5. Other Functions
5.1 Object Tracking
Users can use the control lever on the control keyboard to move the Dome
camera up and down, or left and right to track the moving object or change the field of
vision, and change the visual angle or the image of the object by adjusting the focal
length. On the preset condition of auto-focusing and auto-aperture, the camera can
adjust itself quickly to get a clear view of the object according to the environment
during its moving around.
﹡Focal Length/Rotating Speed Auto-matching Technology
When manual adjusting the Dome camera with a long focal distance, the high
rotating speed of camera may cause image loss even touch the control lever slightly.
Considering the humanization, this ball camera is designed to auto-adjust both the
horizontal and vertical rotating speed according to the focal length which makes the
manual operation of tracking easier.
﹡Auto-overturn
When the operator turns the scene to the bottom (vertically) and continues
pressing the control stick, the camera will turn 180° horizontally and then upturn 90°
to get a back view, which provides a 180° whole-course continuous monitor.
5.2 Camera Control
5.2.1 Zoom Control
Users can zoom in or out by using the [WIDE] and [TELE] key on the control
keyboard to get an overall perspective or a close shot.
5.2.2 Focusing Control
Auto-focusing is the default setup. When zooming, the camera will auto-focus on
the center of the view to get a clear picture. In particular situation, users can manually
focus by using the [NEAR] and [FAR] key to get an expectant view.
◆Camera cannot auto-focus on following conditions:
a. The object is not in the center of the picture;
b. The objects from both far and near spots cannot be visually clear simultaneously;
c. The object emits strong light, such as neon light and spotlight;
d. The object is behind a class with water dew or dust on it;
e. The object moves very fast;
f. The object is large and monotonous, like a wall;
g. The object is too dark or blurry itself.
5.2.3 Aperture Control
●Auto-iris is the default setup. This function can auto-detect the light condition of
the environment and adjust accordingly to ensure the brightness of the output picture
stable.
●Users can manually adjust the aperture to get a needed brightness by using the
control keyboard.
●Users can restore the auto-iris function by using the control keyboard (Note:
auto-iris is suggested).
Note: When switching the aperture control to manual function, the current
control position will be locked, and it will not restore to auto-aperture function
automatically, even the scene changes. To restore the auto function, users need to
operate the control lever or give a control order.
5.2.4 Auto BLC
The camera will divide the scene into six areas to realize the auto back light
compensation. In a bright environment, it will auto-compensate the dark object and
adjust the lighting for the bright background, in order to avoid obtaining an
over-bright picture without visualizing the dark object instead of a clear image.
5.2.5 Auto WEB
Automatically adjust according to the lighting of the surroundings to recover the
true colors.
6. Camera 【OSD】Setup
The Dome Camera menu could be set with keyboard, but some of them could not
be set.
The following【OSD】setup is only applied to the standard cameras that the dome
camera producer manufactured.
6.1. 0 Enter Camera【OSD】
a. Click “CALL” button
b. Input 55
c. Click “Enter” button, and then exit.
6.1. 1 Quit from Camera【OSD】
a. Click “CALL” button
b. Input 55
c. Click “Enter” button, and then exit.
Notice: If you want to go back to the main menu, please click the last option “BACK
TO MENU” or click [CALL] + [112] when you stay in the second submenu. After
that, please carry out 6.1.1 operation to drop out OSD control menu.
6.2. 0 Camera【OSD】Menu Items
Menu includes main menu and submenu. When entering the Camera【OSD】, you
can open the selected items by controlling “UP”、“DOWN”、“LEFT”、“RIGHT”
buttons on the keyboard lever. (The flickering items indicate that they have been
selected.)
● Main Menu displays 6 options.
MAIN MENU
INITIAL
GENERAL
FOCUS
EXPOSURE
PRIVACY
WB
Menu Operation
■INITIALSET
●Make functions restore to the factory default.
■ LENSAUTOINIT
●Lens auto initialization function can be achieved by counting the number of lens
zoom. You can select 5K、10K、20K, EXCE and OFF. Regrouping makes images
clearer.
■ GENERAL
● Set Camera’s normal operations
● Control “DOWN” to enter the submenu.
1. CAMERAID
● Show the Camera’s identification number.
● The ID of Camera No.001-255
can be set by using NEAR/ LEFT、 FRA/
RIGHT .
2.
MIRROR
● Mirroring can be done to the images taken by the Camera.
Menu Operations
Add menu operations
3. SHARPNESS
● Adjust image sketch, and High/ Middle/ Low can be set.
4. COLORSUPPRESS
● Pictures can be changed into white and black pictures in a certain dark
circumstance, and improve the signal noise ratio.
5. LUXLEVEL
● Camera can be adjusted by using LEFT/ RIGHT to control the electrical level
high/ middle/ low.
6. APERTURESUPPRESS
● Reduce noise point in a certain dark circumstance to enhance signal noise ratio.
7. HIGHL I GHTSUPPRESS
● Restrain highlight as black、light color in a certain highlight.
8. THGHLIGHTSUPPRESS
● Camera highlight can be adjusted by using LEFT/ RIGHT to control electrical
level high/ middle/ low.
9. BAUDRATE
● (﹡Manufacturer reserves, and any changes are forbidden.)
● BACK TO MENU
MENU OPERATIONS
1. FOCUS MODE
FOCUS MENU
NORM
SENSITIVITY
NORM
NEARFCSLIMIT
002
W/ T 50cm/ 1m
AF SPEED
BACK TO MENU
←
FOCUS MODE
1.1 NORM
●This kind of mode will make lens stay in a continuous focusing state in a very long
time. If users do not want the lens to stay in the focusing states, interval trigger
focusing state or zoomed trigger focusing mode could be their best choice. By
selecting one of these two modes, the time for using lens will be extended.
1.2 INTV
AF Interval Time
●
Set the auto focus interval time (001~120sec.) by controlling LEFT/ RIGHT
button.
1.3 ZMTR
Run Time
● Set the running time (001~120sec.) by controlling the NEAR/FAR button.
1.4 MANU
● Choose this mode to exit. Then adjust focus by “LEFT/ RIGHT” button.
MENU OPERATIONS
2. SENSITIVITY
● Adjust the auto focusing sensitivity.
3. NEAR FOCUS LIMIT
●The full-view auto-focus system of the Camera can continuously take pictures,
from close-up (the object is nearly 1cm away) to infinity. Make sure that the focus is
in the recent locations. Users can adjust close focus limited parameters to achieve the
fastest focus speed. For example, if the subjects to be taken are beyond 5M, the close
focus limiest parameter can be set above 006.
Near Focus Limited Specifications:
000
001
002
003
004
005
006
007
008
1cm/1m
10cm/1m
50cm/1m
1m/1m
2m/2m
3m/3m
5m/5m
10m/10m
infinity
4. BACK TO MENU
AE MODE
AL
BACKLIGHT
OFF
BACKTOMENU
←
■AE MODE( Shutter setting)
1. AE (Auto shutter)
2. AI (Auto aperture)
3. MANU (Manual setting)
4. SHUTTER (Manual setting)
●The range of shutter speed is 1/50(1/60)、1/120(1/100)、1/250、 1/500、1/1K、
1/2K、 1/4K,、1/10K 、1/100K
5. IRIS
The range of iris is CLOSE, F1.6-F16.
6.AGC
●The range of AGC is 5db\ 13db\ 22db\ 30db.
FLICKERLESS MUST BE OFF
●WARNING: FLICKERLESS MUST BE OFF.
■ FLICKERLESS
●The default options are: Normal, Cable Control, Steady and Off.
■ BACK TO MENU
■ BACKLIGHT OFF (Backlight setting)
1. SENS
GAIN
● Set backlight sensitivity
● Gain control can be set in the range of 0~255 through LEFT/ RIGHT.
5. AREA
Checking area
2.1 OFF
Backlight off
2.2 AREA1
Set middle window backlight
2.3 AREA2
Set below 1/3 window backlight
2.4 AREA3
Set left middle window backlight
2.5 AREA4
Set right middle window backlight
2.6 AREA5
Set upper 1/3 window backlight
﹡If the subjects that you want to take are so dim due to the strong
backlight, you can set the BLC “ON”. Then Camera will balance light
automatically to make images clearer. This function could not be applied
to the situation that the objects are too small comparing with the
background.
MENU OPERATIONS
1. UNWEIGHTED LEVEL
● Set Backlight Weighted Average
● 0~15 optional
2. BACK TO MENU
AEMODEMUSTBEAE
● WARNING: AE MODE MUST BE AE.
MENU OPERATIONS
■ PRIVACY
MASKSET
MASKNUMBER
MASKSET
<1—8>
OFF
H. STARTPOSITION
H. ENDPOSITION
V. STARTPOSITION
V. ENDPOSITION
MASKCOLOR
HOLD
BACKTOMENU
←
MUSTOPERATEONMANUFCS
1. MASK NUMBER
●8 areas can be set.
MASK SET
[Mosaic window setting]
H. STARTPOSITION
[Horizontal start position]
H. ENDPOSITION
[Horizontal end position]
V. STARTPOSITION
[Vertical start position]
V. ENDPOSITION
[Vertical end position]
MASKCOLOR
[Mosaic window color]
● Optional colors for MASK are: HOLD, GREY, WHIT, BLAC, RED, ORAN, YELL,
GREE, BLUE and PURP.
1. BACK TO MENU
● WARNING: Must be on manual focus model.
■ WBC MODE
WBCMODE
WBCMODE
ANTI-COLORMUSTBEOFF
BACKTOMENU
←
1. PUSH
Adjust BLC automatically and quickly.
2. MANU
2.1 WBC ADDITION
●Chose this option if you want to add / reduce red or blue correction.
3. INDR
Set temperature is about 3200K..
4. FLUO
Set temperature is about 4700K.
5. OUTD
Set temperature is about 9500K.
6. AUTO
Adjust image color automatically according to the effective illumination.
7. BACK TO MENU
﹡ After return to the main menu, click [CALL] button, then input [112], lastly click
[ENTER], then you can go back to OSD control menu.
Protocol、Transmission rate and ID should be set correctly when other control
equipments are used to control the Dome Camera. Because different manufacturers
have different ID codes, sometimes the Camera ID is needed to be set as “ID+1”. For
example, the Dome Camera could not be controlled by DVR until its ID is “2”. The
rest can be done in the same manner.
7. TROUBLESHOOTING
Problems
Possible reasons
Solutions
Power supply damaged or
Replace
No action, no
under power
pictures when
Wrong connection of power
Correct
Project line fault
Eliminate
Mechanical failure
Recondition
Camera inclined
Reinstall
power is on
Abnormal selfcheck. Images
Replace required power supply; Put
with motor
Power supply not enough
power supply close to Dome
noise
Camera
Normal self-
Wrong connection of video
Correct
check, but no
Bad connection of video
Eliminate
images
Camera damaged
Replace
Wrong connection of signal
Correct
Normal self-
control cable
check, but out
Dome ID setup is wrong
Reselect
of control
Protocol or communication
Adjust protocol to match with the
baud rate is not matched
controller, and power on again
Unstable
Bad connection of video
Press to connect well
images
Power not enough
Replace
Self-check error
Power on again
Bad connection of control cable
Eliminate
Bad host operations
Power on again
Dome Camera
out of control
Overload or communication
Add code distributor
distance too far
8. Appendix 1: Lightning and Surge Protection
The product adopts TVS plate lightning protection technology, which is effective for
avoiding the damage of equipments from pulse signal under 1500W HP, such as those
from instant lightning or surge. However, for outdoor installation, necessary
protection must be adopted according to the situation on condition that the electric
safety must be guaranteed.
 The transmission line must be at least 50 meters away from high-voltage
equipments and cable; try to arrange the line along the eaves.
 The underground sealed steel tube arrangement must be adopted in open area,
and the single point earthing must be used. The overhead ground arrangement is
absolutely forbidden.
 In the intense thunderstorm or high induced voltage area (e.g. High-Voltage
Junction Box), such methods as the installation of extra superpower lightning
protection equipments or lightning rod must be adopted.
 The design of outdoor device and the lightning protection and earthing of line
must meet the requirements of the building’s lightning protection, and be in
accordance with relevant national and industrial standards.
 The system must be earthed with equal potential. The earthing device must
meet the requirements of both anti-interference and electric safety, and mustn’t
connect to, or mix with the zero line of any strong power grid. When the system
adopts the earth connection alone, the impedance should be no more than 4Ω, and
section surface should not excess 25mm2.
Appendix Ⅱ: Cleanness of Transparent Cover
● To keep the image clear, the transparent cover of Dome Camera should be clean at
regular intervals.
● Please be careful while cleaning the transparent cover. You have to hold the outer
ring of transparent cover to avoid touching the bottom guard directly. Otherwise,
acid sweat on our fingers might corrupt the appearance of the cover, while the
scratches caused by hard objects will result in images blur, affecting the image
quality.
● Please clean inner and exterior transparent cover with tender dry cloth.
● Neutral cleaner can be used to clear away serious dirt, and any cleaner products
for advanced furniture are fit for cleanness.
Appendix Ⅲ: General Knowledge of RS485
1. Basic Characteristics of RS485
According to its standard, RS485 industrial bus is a half-duplex C-bus of special
impedance 120 Ω, whose largest loading capacity is 32 payloads. (Including master
device and controlled device)
2. The transmission distance of RS 485
Band Rate
Maximum Transmission Distance
2400Bps
1800m
4800 Bps
1200m
9600 Bps
800m
3. Connection mode and terminal resistance
a) RS 485 industrial bus standard requires that daisy chained ways should be
adopted among devices with 120Ω terminal resistors at both ends. The connection
(picture 26) can be simplified as that in picture 27, but “D” distance should not be
more than 7m.
A) The connection mode of device terminal 120Ω: (As picture 43) there are
device terminal resistances on controller board, which have two connection modes.
Picture 43 shows the factory default connection mode. In this case, the wire jumper
cap on controller board is connected to the position between 2-3 sockets without
120Ω resistor connected. When 120Ω resistor is required, the wire jumper cap on
controller board should be pulled out of 2-3 sockets to plug into the 1-2 ones. Then
the 120Ω resistor is connected to circuits.
4. Some problems in application
Star connection is always adopted by users in application. In this situation, the
terminal resistors should be on the 1# and 15# (as it is shown in picture 28) of two
devices with maximum line distance. However, this connection type is not consistent
with the operating requirements of RS 485 industrial standard, so the problems, like
signal reflex and the decrease of anti-jamming capability, easily occur, which may
reduce the reliability of controlled signal. The phenomenon reflected is that balling
machine is completely or discontinuously out of control, or that it cannot stop running.
To solve these problems, we propose to use MC 2080 Rs485 distributor, because this
product can convert the star connection mode to that one accord with RS 485
industrial standard, avoiding problems to improve the reliability. (Picture 29)
Appendix Ⅳ
Relational Table of 24V AC Line Diameter and Transmission Distance
The maximum transmission distance is recommended in the situation that the
line diameter is fixed and 24V AC voltage wastage rate is below 10%. As for the AC
main power supply devices, their maximum allowable voltage wastage rate is 10%.
For example, a device with an 80 VA rated power is installed in a place 35 feet away
from the transformer, then the required minimum line widths should be 0.8000 mm.