890 Manual - Discover Your Mobility Main Menu.!

C.T.M. MOBILITY SCOOTER
8-Series Instruction Booklet
HS-850
HS-890
8-Series
Instruction Booklet
TABLE OF CONTENTS
INTRODUCTION --------------------------------------------------------1
IMPORTANT PRECAUTIONS ----------------------------------------2
ELECTROMAGNETIC INTERFERENCE AND WARNINGS ----3
IDENTIFICATION OF PARTS ----------------------------------------5
OPERATING YOUR SCOOTER -------------------------------------7
DISASSEMBLING YOUR SCOOTER -------------------------------9
ASSEMBLING YOUR SCOOTER ----------------------------------11
CHARGING THE BATTERIES --------------------------------------12
CARE AND MAINTENANCE ----------------------------------------13
TROUBLESHOOTING ------------------------------------------------14
TECHNICAL SPECIFICATIONS ------------------------------------15
8-Series
Instruction Booklet
INTRODUCTION
Thank you and congratulation on purchasing your new C.T.M. Mobility Scooter.
It is designed to provide you with transportation ability indoors and outdoors.
We pride ourselves on providing safe and comfortable products. Our goal is to ensure your
complete satisfaction. We sincerely hope you enjoy your C.T.M. Mobility Scooter.
Please read and observe all warning and instruction provided in owner's manual before you
operate with various convenient function of this scooter. Also, please retain this booklet for
future reference.
If you have any question, you can contact :
C.T.M.HOMECARE PRODUCT, INC.
6191 Schaefer Ave Suite B Chino CA 91710
Tel : +909-590-1388 Fax : +909-590-3365
E-Mail : ctm@ctmhomecare.com http : //www.ctmhomecare.com
or your local dealer:
1
8-Series
Instruction Booklet
IMPORTANT PRECAUTIONS
•Only one person at a time could ride a C.T.M. Mobility Scooter.
•Maximum load is HS-850 205 kgs/ 450 lbs & HS-890 227 kgs/ 500 lbs.
•Turn key off before getting on or off.
•Always drive carefully and be aware of others using the same area.
•Always use pedestrian crossings wherever possible. Take extreme care when crossing
roads.
•Do not drive on slope exceeding 12 degree, and take extreme care when turning on slope.
•Do not use full power when turning to sharp corner.
•Take great care and drive in low speed when backing up, riding downhill or on uneven
surface, and climbing curb.
•Scooter may not operate well in high humidity.
•If you are caught in rain, it is handy to carry a scooter canopy. It offers complete
protection for your and scooter.
•Never put scooter in neutral when staying on slopes.
•Follow traffic laws when riding outside.
2
8-Series
Instruction Booklet
ELECTROMAGNETIC INTERFERENCE
AND WARNINGS
CAUTION: It is very important that you read this information regarding the possible
effects of Electromagnetic Interference on your motorized scooter.
Powered wheelchairs and motorized scooters may be susceptible to electromagnetic
interference (EMI), which is interfering electromagnetic energy (EM) emitted from sources
such a radio stations, TV stations, amateur radio (HAM) transmitters, two-way radios, and
cellular phones. The interference (from radio wave sources) can cause the motorized
scooter to release its brakes, move by itself, or move in unintended directions. It can also
permanently damage the motorized scooter control system. The intensity of the interfering
EM energy can be measured in volts per meter (V/m). Each motorized scooter can resist
EMI up to a certain intensity. This is called its "immunity level." The higher the immunity
level, the greater the protection. At this time, current technology is capable of achieving
at least a 20 V/m immunity level, which would provide useful protection from the more
common sources of radiated EMI. The immunity level of this motorized scooter model is
not known.
There are a number of sources of relatively intense electromagnetic fields in the everyday
environment. Some of these sources are obvious and easy to avoid. Others are not
apparent and exposure is unavoidable. However, we believe that by following the warnings
listed below, your risk to EMI will be minimized.
The sources of radiated EMI can be broadly classified into three types :
1.Hand-held portable transceivers (transmitters-receivers) with the antenna mounted
directly on the transmitting unit. Examples include: citizens band (CB) radios, "walkie
talkie," security, fire, and police transceivers, cellular telephones, and other personal
communication devices
Some cellular telephones and similar devices transmit signals while
they are ON, even when not being used
2.Medium-range mobile transceivers, such as those used in police cars, fire trucks,
ambulances, and taxis. These usually have the antenna mounted on the outside of the
vehicle; and
3.Long-range transmitters and transceivers such as commercial broadcast transmitters
(radio and TV broadcast antenna towers) and amateur (HAM) radios
Other types of hand-held devices, such as cordless phones, laptop
computers, AM/FM radios, TV sets, CD players, and cassette players,
and small appliances, such as electric shavers and hair dryers, so far as.
we know, are not likely to cause EMI problems to your motorized scooter.
3
8-Series
Instruction Booklet
Motorized Scooter Electromagnetic Interference:
Because EM energy rapidly becomes more intense as one moves closer to the transmitting
antenna (source), the EM fields from hand-held radio wave sources (transceivers) are of
special concern. It is possible to unintentionally bring high levels of EM energy very close
to the motorized scooter control system while using these devices. This can affect
motorized scooter movement and braking. Therefore, the warnings listed below are
recommended to prevent possible interference with the control system of the motorized
scooter.
Warnings:
Electromagnetic interference (EMI) from sources such as radio and TV stations, amateur
radio (HAM) transmitters, two-way radios, and cellular phones can affect motorized scooters.
Following the warnings listed below should reduce the chance of unintended brake release
or motorized scooter movement which could result in serious injury.
1.Do not operate hand-held transceivers (transmitters-receivers), such as citizens band
(CB) radios, or turn ON personal communication devices, such as cellular phones, while
the motorized scooter is turned ON;
2.Be aware of nearby transmitters, such as radio or TV stations, and try to avoid coming
close to them;
3.If unintended movement or brake release occurs, turn the motorized scooter OFF as
soon as it is safe;
4.Be aware that adding accessories or components, or modifying the motorized scooter,
may make it more susceptible to EMI; and
There is no easy way to evaluate their effect on the overall immunity of
the motorized scooter.
5.Report all incidents of unintended movement or brake release to the distributor listed
on the inside front cover of this manual. Note whether there is a source of EMI nearby.
Important Information:
1.20 volts per meter (V/m) is a generally achievable and useful immunity level against
EMI (as of May 1994). The higher the level, the greater the protection.
2.The immunity level of this product is at least 20/Vm.
4
8-Series
Instruction Booklet
IDENTIFICATION OF PARTS
Before attempting to drive this scooter on your own, it is important that you familiarize
yourself with the controls, and how to operate
Tiller Angle
Adjustment
Swivel Seat
With Head Rest
Thumb Lever
Basket
Storage Area
Tiller Angle
Adjustment
Seat Rotation
Lever
Head light
Turn Signals
Reflectors
Seat Sliding
Slide Lever
Front Bumper
12" Front and Rear Wheels
Figure 1 - HS-890 Front View
Battery Gauge
Power/Self-Diagnostic
Warning Light
Warning
Light
Speed Dial
Knob
Armrest
Width
Adjustment
Thumbscrews
Storage
Area
Rear
Turn Signals
Horn
Left Turn Signal
Hi/Lo Speed Switch
Right Turn
Signal
Rear Bumper
Headlight
Anti-tip Wheels
Figure 2 - HS-890 Control Panel
Figure 3 - HS-890 Rear View
5
8-Series
Instruction Booklet
FUNCTION OF PARTS:
TOP CONTROL PANEL
•Speed Dial Knob
The Rabbit means fast and Turtle is slow. By turning this you control total speed
transferred to thumb controls.
•Battery Gauge
There is a meter shows batteries capacity status.
ADJACENT TO TOP CONTROL PANEL
•Thumb Lever
Pushing right thumb lever moves scooter forward. Pushing left thumb lever moves the
scooter backward. (This can be reversed if required by local dealer.) Releasing both,
engages automatic brake. These are also your accelerator. The further you depress
them, the faster you go. (Subject to the position of the Rabbit/Turtle control).
AT BASE OF STEERING TILLER
•Tiller Angle Adjustment
Pull downward the tiller adjustment to adjust tiller angle and release to lock at
comfortable position.
BELOW SEAT
•Seat Height Adjuster
There are three holes on seat tube to adjust seat height. Be sure the detent pin is fully
inserted at its new height before sitting.
•Armrest width Adjustment Thumbscrews
Loosen the two thumbscrews to adjust arm width; tighten again to lock in at desired
position.
•Legroom Adjuster
There are few holes on front and rear frame tube for adjusting legroom. Pull the toggle
latch to loosen and insert the detent pin to locate the position. Push the toggle latch
again to lock.
REAR BODY
•Rear Compartment Cover
Open the compartment Cover to access on board charger.
•Anti-tip wheels
Helps keep scooter from tipping over.
•Free-Wheeling Lever
When lever is in N (Neutral) position, scooter can be moved without power.
When lever is in D (Drive) position, scooter can be driven. Normal position is D.
6
8-Series
Instruction Booklet
OPERATING YOUR SCOOTER
You could make the following adjustments to increase your comfort when driving.
•adjust seat height and location
•adjust armrest width to comfortable position.
•adjust legroom.
1.Before operating your scooter, check the following:
•free-wheeling lever in D
•speed dial knob is at turtle picture.
2.Sit on scooter and turn on key, Battery Gauge meter should be indicate at F.
The Self-Diagnostic Warning Light should not be blinking.
3.When your hands rest comfortably on handlebars, the thumb levers should be within easy
reach. The right lever moves scooter forward, the left one moves it backward. When you
release both levers, scooter will stop.
This scooter has automatic braking system. Release the thumb lever
and brake will stop scooter.
4.Steer scooter by turning tiller toward the way you want to go.
5.Practice driving where there are is No obstacle. Start at the slowest speed and drive
forward and backward; make some turns. As you get more comfortable, you can increase
speed by turning speed dial toward picture of rabbit.
6.If Battery Gauge indicates E, you should plan to recharge batteries very soon.
7.If scooter stops, locate the circuit breaker on top of battery pack. Push it and try
driving again.
8.When you are finished riding, turn off the key before getting off.
9.If you are finished riding for the day, immediately recharge batteries.
See CHARGING THE BATTERIES, page 12.
7
8-Series
Instruction Booklet
Keep in mind these rules:
•Release thumb levers and allow scooter to stop completely before changing from
forward to reverse, or reverse to forward.
•When turning to corner, swing front wheels widely, so back wheels will turn more tightly.
•Use scooter only where it is safe for walting.
•Drive in low speeds when reversing, riding dowhill, over rainp or curb, or on uneven
sukpace, downhills, ramps, curbs, or uneven surfaces.
Other Operating Information:
Hill climbing: You may need to use a higher speed. Turn to lower speed before going
downhill.
Down slopes: proceed with downward slopes slowly, and set speed control in proximity
of turtle. The closer speed control is set toward turtle, the slower scooter
travels. However, this scooter will not self accelerate down hills due to the
automatic braking, taking effect should you attempt to drive too fast.
Kerb climbing: Approach slowly from right angles to curb. A slight angle is permissible
with a 4-wheel scooter, but a direct approach is needed on a 3-wheel
scooter. Do not attempt greater than a 3" curb.
If Self-Diagnostic Warning Light starts to blink, identify problem from
chart on page 14 and take action.
If the scooter breaks down and must be moved, get off scooter, engage
Free-Wheeling Lever to N, push scooter slowly to a safe location, and
push lever back to D.
In unlikely event of a panel display error, you need to re-set the display
system by cycling the on/off main switch. The display circuitry is independent
of the motor control system. A display console error does not affect scooter
speed control.
8
8-Series
Instruction Booklet
DISASSEMBLING YOUR SCOOTER
The HS-890's compact design and light weight style make it fit easily into trunk or back
seat of most vehicle. No tools are necessary to disassemble scooter.
Remove seat by releasing Seat Rotation Lever (A) and then lift seat off. (See Fig. 4)
Remove rear shroud (B) off scooter. (See Fig. 5)
(B)
(A)
Figure 4
Figure 5
Unscrew two wire connectors (C) between front and rear units. (See Fig. 6)
Detach battery power plugs (E). (See Fig. 7)
(E)
(C)
Figure 6
Figure 7
Remove battery fixing Velcro (D). (See Fig. 8)
Remove batteries (F). (See Fig. 9)
(D)
(F)
Figure 8
Figure 9
9
8-Series
Instruction Booklet
Remove front basket (G) and lower tiller by pulling tiller adjustment (H) and push tiller
doun. (See Fig. 10)
When fintsh instruction from figure (4) to figure (10) , there are 5 main parts. (See Fig. 11)
(H)
(G)
Figure 10
Figure 11
10
8-Series
Instruction Booklet
ASSEMBLING YOUR SCOOTER
To assemble scooter, you can repeat disassembly directions in reverse. Abbreviated
directions are given below. Refer to Figures on pages 9 - 11 to locate parts.
1.Use the tiller adjustment to move tiller up and out of the way.
2.Place front basket.
3.Place battery pack in battery compartment.
4.Place seat on seat post and tighten seat locker knob.
11
8-Series
Instruction Booklet
CHARGING THE BATTERIES
Batteries must be charged before using the scooter for the first time and should be
recharged after each day use. You will need the scooter and the battery charger.
Each country may supply different
charger. The charging procedure
may be different from below.
If you require more details, please
contact your authorized dealer.
Be sure the scooter key is in the
OFF position
Figure 12
1.Insert battery charger cord into the charger connector on the charger output. Refer to
above figure for correct position
2.Plug the other end of the battery charger cable into a standard electrical outlet.
3.Turn the power on. Normally, The LED (Power) Light will turn on when electric current
passes.
4.Charging starts. During charging, LED (Charge) will indicate orange light, when it turns
to green light, that means well-charged.
5.LED indication
•LED(POWER) - GREEN LIGHT ON : Power On.
•LED(CHARGE) - ORANGE LIGHT ON : Charging / GREEN LIGHT ON : Fully Charged
6.Charger Trouble Shooting
(A)If LED (POWER) light is off
•Check the input voltage (115V/230V) is the same as you adjust.
•If light is still off, please check and repair the battery charger.
(B)If LED (CHARGE) light is off
•Check to see clips connection is correct.
•If the battery is fully charged, the LED (CHARGE) light will be off.
•If light is still off, the battery may be defective.
(C)If ORANGE light can turn to GREEN
•The battery can not be charged. Please check and recover it.
(D)If ORANGE light turns to GREEN immediately
•Check to see the battery is fully charged, if not, The battery may be defective
Check and recover it.
The time needed to recharge will vary depending on the depletion of the
batteries. Charging for longer than necessary will not harm the batteries.
They can not be overcharged.
Keep in mind these rules:
•Fully charge batteries at least once a month, or more if you use scooter regularly.
Charge after each trip exceeding 3 kilometers.
•If storing your scooter for some time (1 month or more), make sure that batteries are
fully charged, and on returning, charge them again before using scooter.
•Batteries will only give maximum performance after scooter has been used, and batteries
have been recharged up to 10 times. A bit like breaking in a new car.
12
8-Series
Instruction Booklet
CARE AND MAINTENANCE
Cleaning Your Scooter:
If your scooter is dirty, use a damp or lightly soapy cloth to wipe it down. Do not use running
water to wash or rinse scooter in order to protect electrical parts. Polish with an automotive
liquid polish.
Maintaining Your Scooter:
All maintenance and repair of scooter should be done by an authorized dealer.
The following areas required periodic inspection:
•Tire pressure between 30-50 lbs
•All electrical connections are firmly attached
Storing Your Scooter:
Between uses, your scooter is best stored in a dry location.
13
8-Series
Instruction Booklet
TROUBLESHOOTING
Here are some suggestions about solving problems you may have with your scooter. There
is a Self-Diagnostic Warning Light on the Control Panel. To check the Self-Diagnostic
Warning Light, turn on the key and count the number of blinks on the Warning Light.
Number of
Flashes
Problem
Solution
1
Battery needs
recharging
Recharge the batteries soon.
2
Battery voltage too low
to operate scooter
Must recharge before using. Check
battery condition and connections.
3
Battery voltage too high
Check battery condition and connections.
Contact your authorized dealer to check
your battery charger.
4
Short in motor
Contact your authorized dealer.
5
Brake malfunction
Contact your authorized dealer.
6
Thumb lever not in
neutral
Contact your authorized dealer.
7
Thumb lever malfunction Contact your authorized dealer.
8
Motor problems
Contact your authorized dealer.
9
Other internal errors
Contact your authorized dealer.
Other Problems
Low tire pressure: pump up tires to 30-50 lbs.
During charging, light on charger does not change to green: Contact your authorized dealer.
Scooter will not move when key is turned on:
1.Check Power Reserve Indicator on control panel, it should be lighting in green, yellow, and
red zones.
2.Check Self-Diagnostic Warning Light, it should be steady. If it is flashing, see chart above
for problem identification.
3.Check all electrical connections to be sure they are tight.
4.If none of above correct problem, contact your authorized dealer.
14
8-Series
Instruction Booklet
TECHNICAL SPECIFICATIONS
SPECIFICATIONS
HS-850
HS-890
Overall Length
57.1"
60.2"
Overall Width
27"
27"
Overall Height
49"
49"
Wheels: Front
13"
13"
Wheels: Rear
13"
13"
Weight w/ Batteries
214 lbs
251 lbs
Max. Speed
9.3 mph
8 mph
Weight Capacity
450 lbs
500 lbs
3.3"
3.3"
12 degree
10 degree
Curb Climbing
2.4"
2.8"
Turning Radius
68.1"
68.1"
Front & Rear
Front & Rear
Electro-Mechanical
Electro-Mechanical
Ground Clearance
Grade Climbable
Suspension
Brake
Seat Type
Sliding and Swivel RecliningCaptain W/Headrest
Seat Width
19"
22"
Motor Size
700W 5400 r.p.m
700W 5400 r.p.m
(2) 12V. 50Ah
(2) 12V. 50Ah
Battery Weight
69 lbs
69 lbs
Travel Range
23.4 Miles
23.4 Miles
5A Off Board
5A Off Board
Battery Size
Battery Charger
Electronics
On/Off Key Switch, Battery Level Indicator,
Speed Control Knob
*Subject to change without notice.(Issue A)
15
Download PDF
Similar pages
Battery Charger Troubleshooting
EM Owners Manual Pioneer Issue 04 1014
Modcharger User Guide v1.1
SameZone Mini Self Balance Electric Scooter User Manual - G-Tec
EME Owners Manual Liteway 3&4 Plus