cPCI-SBC01

cPCI-SBC01 Board User manual
cPCI-SBC01
(EMB-CPU01)
User’s Manual
Windows, Windows2000, Windows NT and Windows XP are trademarks of Microsoft. We acknowledge that the
trademarks or service names of all other organizations mentioned in this document as their own property.
Information furnished by DAQ system is believed to be accurate and reliable. However, no responsibility is assumed by DAQ
system for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is
granted by implication or otherwise under any patent or copyrights of DAQ system.
The information in this document is subject to change without notice and no part of this document may be copied or
reproduced without the prior written consent.
Copyrights  2007 DAQ system, All rights reserved.
-1-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
Contents
1 . cPCI-SBC01 Introduction
2 . cPCI-SBC01 Appearance
3 . cPCI-SBC01 Assembly (Memory, Hard Disk)
4 . Peripheral Device Control through Compact PCI
Interface(Back-Plane Connection)
5 . Expansion Port through Transition Board
6 . WINDOWS & Driver Installation
-2-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
1 . cPCI-SBC01 Introduction
Introduction

It is the low cost Single Board Computer(SBC) which equipped a low power and
low heat processor.

It provides solution to be suitable for Embedded market wanting low power and
small size.
Features

Low cost, Low power and fan-less Single Board Computer

AMD Geode LX800 500MHz processor

256Mb ~ 1Gb memory

IDE Hard disk interface, (option)CF card

VGA, (option) TFT LCD video output

2xUSB, 1xAudio (Transition board – 2xUSB, 2xPS2, RS232, 1xFDD, 1xLPT)

Ethernet 10/100/1000M

Embedded model available

Operating Systems - Windows 2000/XP
Specifications
H/W
•
AMD Geode LX800 500MHz processor
•
256MB, up to 1GB DDR SODIMM SDRAM
•
Compact Flash card (2G/4G/8G) (option) 1.8inch IDE HDD
•
1920*1440 VGA output, (option) TFT LCD video output
•
AC’97 codec sound
Physical Dimension
•
•
160 x 100 x 30 mm
Front I/O : Power switch, D-sub video connector, 2xUSB, Ethernet,
2xStatus LED, Audio
•
Rear (transition) board : 2xUSB, 2xPS2, RS232, 1xFDD, 1xLPT
•
On-Board : LCD output, IDE
Application

Factory Automation

Data acquisition

Medical and Robotics

Auto PC

UMPC(Ultra Mobile PC)

Instrument control PC
-3-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
2 . cPCI-SBC01 Appearance
+5V External Power
Front side
SW,VGA,Network,USB
Rear side
Compact PCI interface
- The cPCI-SBC01 board can use to personal PC with the external Power +5V. In front
side of the cPCI-SBC01 have the Connector Out (VGA, Power S/W, Ethernet, 2xUSB,
Power LED, Audio-Jack).
- The cPCI-SBC01 board connects the Back-Plane at rear side. It can control the other
devices through compact PCI interface.
-4-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
3 . cPCI-SBC01 Assembly(Memory, Hard Disk)
1. Memory(SODIMM – SDRAM) Connection
- Memory Connection with J4 connector(256M ~ 1G)
- CF card connector board
(It is necessary to change the board if it connects 1.8” hard.)
-5-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
- Hard Disk Connection (This picture is CF card connection.)
Notice) It is necessary to change the board if it connects 1.8” hard. The picture shows differently
above picture
-6-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
4 .Peripheral Device Control through Compact PCI Interface(Back-Plane)
cPCI-SBC01
Switch
Audio
Usage – Our Product cPCI-EK01
VGA
Ethernet
2xUSB
The cPCI-SBC01 can control the other Compact PCI products as to connect BackPlane like above picture.
-7-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
5 . Expansion Port through Transition Board
2xUSB
LPT
FDD
RS232
serial
2xPS2
Expansion rear
interface
IR
The transition board can use through the Back-Plane. And It is possible to use the
expansion ports with connect the cPCI-SBC01. (Special Purchase)
-8-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
6 . WINDOWS & Driver Installation
1. To connect a USB KEYBOARD and USB MOUSE and USB CD-ROM(WINDOWs
CD) at Board. And, connect the power(5V, 3A) after connection to a DSUB 15 PIN
VGA PORT and light up the switch.
Notice) There isn’t an external power supply need in case of Back-Plane use.
2. When the computer boots, press the “F1” at the keyboard. And display the BIAS
SET_UP.
3. After choose the “Boot Order”, Press “Enter”.
4. After choose the “USB CD-ROM Drive <- Conflict 4” at 1 line, and press down the
“Esc”.
-9-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
5. After choose the “Save values and Exit”, and escape the display.
6. Booting is performed with a USB CD-ROM, you are able to progress a windows
install guide.
7. After finished the Windows installation, you have to install the last Board driver.
- There is Driver to CD-ROM enclosed like product.
7.1 AUDIO Driver Installation
- MyComputer => Property => Hardware => Device Manager
- Choose “Audio device”.
- Click the right mouse, select the “driver update”.
- Starting Hardware Update Wizard
- Choose the Driver in AUDIO folder in CD ROM.
7.2 LAN Driver Installation
- Execute SET-UP file in LAN folder in CD-ROM.
7.3 LCD Driver Installation(DISPLAY)
- Choose the DRIVER in LCD folder in CD ROM.
7.4 VGA Driver Installation
- Choose the DRIVER in VGA folder only used VGA.
7.5 Touch Installation(When 7” LCD want to use.)
- After execute the Setup file in Touch folder in CD-ROM, display the icon of
-10-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
TouchWare at the wallpaper.
- Double click the TouchWare.
- Click the “HW Info”.
- Click the “Auto Search Touch” button, check the connection port.
- After finding the port at Touch Controller, press “OK”.
- Choose the “Calibrate” button.
-11-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
- When show the below display, press the lighting point.
(You should continuously press until completed progress bar.)
- Press “Yes”, and then finished the install.
7.6 The optimum display set for the LCD.
-
Change the resolution 800x400 because LCD resolution is optimum 800x480.
-12-
http://www.daqsystem.com
cPCI-SBC01 Board User manual
-
Choose the “Property” in wallpaper.
- Click the “Advancd” in “Setting” in “Display Registration Information” display.
- Click the “List All Modes” in “Adaptor”
- Choose the “800 x 480 true color”.
- Press “OK” and hit “Execute”.
- If you see the red circle in the “Display Registration Information”. All progress
succeed.
-13-
http://www.daqsystem.com