Chronograph User Manual

U s e r ma n ua l
iConic
C H R ONO G R A P H
Watch display and command buttons description
I.
3.
1.
5.
6.
4.
Display
1.Second hand
2.Minute hand
3. Hour hand
4. Centre stop-second
5.Minute counter
6. Hour counter
2.
II.
III.
Command buttons
I. Push button A
II.Crown
III. Push button B
U s e r ma n ua l
iConic
C H R ONO G R A P H
Setting the clock
1. Open the protection’s arm:
Grab the arm protection in the 4 o’clock area and pull outward. The
best way is to pinch the protection arm between thumb and forefinger.
2. Unscrew the crown.
3. Push the crown in setting position.
4.Set the clock:
Crown position I Normal function
Crown position II Date setting
An extreme acceleration in setting the date with quick mode can
induce a false date indication
Crown position IIITime setting
In this position the watch is stopped. Use this mode to save energy
when you don’t use the watch (saving approx. 70%)
5. Pull the crown in position I.
6.Screw the crown.
7. Close the protection arm.
U s e r ma n ua l
iConic
C H R ONO G R A P H
Setting the date following a battery change::
Example: -Date / time on the watch: 28 / 10:10
-Present date / time: 21 / 10 :10
1. Pull out the crown to position II (the watch continues to run).
2. Turn the crown until yesterday’s date appears 9
3.* Pull out the crown to position III (the watch stops).
4. Turn the crown until the correct date (21) appears
5.**Continue to turn the crown until the correct time (10 :10AM)
6. Push the crown into position I.
Changing the battery
To change the battery a special tooling is necessary.
This operation has to be made by a watch retailer service center,
otherwise seal can’t be guaranteed.
Others:
In case your watch needs to be repaired or raise claims under guarantee,
please contact the point of sale.
Please note:
*) To set your watch to the exact second, please refer to the chapter
entitled “setting the clock”.
**) Please observe the AM/PM clock rhythm.
U s e r ma n ua l
iConic
C H R ONO G R A P H
Adjusting the chronograph to zero position:::
In case one or several hands are not in their correct
zero positions and have to be adjusted.
1. Pull out the crown completely to position III.
2. Keep push-buttons A and B pressed
simultaneaously for at least 2 seconds
(the center stop-second rotates by 360˚
> corrective mode is activated)
Adjusting the ce n te r stop-s econ d
I.
Single step: press push-button A 1x short
Continuous: press push-button A 1x long
II.
To adjust the next hand press push-button B
Adjusting the hour coun te r han d
(at 6 o’clock)
III.
Single step: press push-button A 1x short
Continuous: press push-button A 1x long
IV.
To adjust the next hand press push-button B
Adjusting the minute coun te r han d
(at 9 o’clock)
V.
Single step: press push-button A 1x short
Continuous: press push-button A 1x long
VI.
To adjust the next hand press push-button B
3. Return the crown to position 0.
Termination of the chronograph hands adjustment.
This operation can be carried out anytime.
U s e r ma n ua l
iConic
C H R ONO G R A P H
Chronograph, basic function.
(Start/Stop/Reset)
1.Start: Press push-button A.
2. Stop: To stop the timing press
push-button A once more and read
the three chronograph hands.
I. Chronograph minutes counter
II. Chronograph hours counter
III.Chronograph seconds counter
3. Read the three chronograph counter:
in example 5 hours, 14 minutes, 19 seconds
4. Zero positioning (reset):
Press push-button B (the three
chronograph hands will be
reset to their zero positions).
Chronograph, accumulated timing.
(Start/Stop/Restart...)
1. Start: Press push-button A.
2. Stop: press push-button A
3. Read the three chronograph counters:
in example 5 hours, 14 minutes, 19 seconds
4.Restart: Press push-button A.
5.* Stop: press push-button A
6.* Read the three chronograph counters:
in example 5 hours, 18 minutes, 38 seconds
7. Zero positioning (reset):
Press push-button B (the three
chronograph hands will be
reset to their zero positions).
Please note:
* Following (6), the accumulation of the
timing can be continued by pressing
push-button A (Restart / Stop, Restart / Stop).
U s e r ma n ua l
iConic
C H R ONO G R A P H
Intermediate or interval timing.
1. Start timing: Press push-button A.
2. Interval time: To stop the timing and
see interval time, press push-button B
(timing continues in the background).
3. Read the three chronograph counters:
in example 14 minutes, 19 seconds
4.To make up the measured time press
push-button B: The chronograph hands
are quickly advanced to the ongoing
measured time.
5. Final time: To stop the timing, press
push-button A.
6. Read the three chronograph counters:
in example 18 minutes, 28 seconds
7. Zero positioning (reset):
Press push-button B (the three
chronograph hands will be
reset to their zero positions).
Please note:
* Following (2), further intervals
intermediates can be displayed by
pressing pussh-button B (display interval /
make up measured time).