mp700z_3_en.vp:CorelVentura 7.0

COEF srl.
Via Albinatico, 80-82
51019 Ponte Buggianese (PT)
ITALY
www.coef.it / www.coef.net
Realized by PC CAD & VIDEO
Mp 700 zOOM
info@coef.it
•
Code 02E006 - Electronic Ballast
•
Code 02E005 - Magnetic Ballast
• OPERATING INSTRUCTIONS
Printed in November 2001
Declaration of CE conformity
We Manufacturer COEF srl. Via Albinatico, 80-82 / 51019 Ponte Buggianese (Pistoia) ITALY
Declare that the product MP700 Zoom is in conformity with 89/336 EEC-EMC directive and
with the actual required safety standars in accordance with LVD 73/23 EEC
Ponte Buggianese, 10 October 2001
ATTENTION: carefully read the directions of this manual. Exclusively follow the safety rules in force and do not carry
out assembly and/or maintenance operations without taking all precautions as indicated in the different sections or
without the necessary specialization.
This manual must always accompany the equipment, therefore it must be available and readable at any moment if
necessary. Also in case of sale, rent, change of place and/or ownership, these documents shall be enclosed with the
relative equipment.
ADVICES FOR A CORRECT INSTALLATION
This equipment is destined to an exclusively Professional use.
1) Make sure that all the fastening parts of the spotlight are in good condition. Regulate the proportions of the fastening accessories (screws, bushes, nuts, supports, etc.) in order to be slightly over-dimensioned as compared to the actual requirements.
2) Carefully check the contents of the packaging and the completeness of the components. If any of the parts listed hereunder
is missing, please contact your Dealer immediately.
3) Do not install the projector outside where the influence of atmospheric factors could damage the unit working (rain, wind,
intense heat etc.) or indoor if there is a high percentage of humidity.
4) Do not clean the projector using water jets or immersion in different liquids. Scrupulously follow the indications given in the
chapter MAINTENANCE.
5) Make the electric connections and the installation / replacement of the lamp after having disconnected the power supply and
after haved positioned the power switch to OFF.The apparatus is classified as belonging to Class 1 type of protection against electric shocks. Its connection to an earthed mains unit is compulsory. The equipment must be protect by an adeguated magnetothermal switch. You are recommended to equip the system with aptly dimensioned differential switches.
6) Do not touch in any case the internal and external parts of the projector without previous authorization of the constructor
and make modifications only by the intervention of qualified staff.
7) Make sure that the projector is correctly fixed on the support as indicated in par. 3.3
8) If the bulb explodes, the particular design of the apparatus prevents the splinters from going outside the projector. All the
parts, therefore, shall be complete and perfectly assembled. The lenses, if visibly damaged, shall be replaced by original spare
parts.
9) Minimum distance from illuminated objects: The projector must be positioned in such a way that objects struck by the
light beam are located at least 2 metres from the projector objective.
2 mt.
10) Minimum distance from inflammable materials: 0.3 meters
11) MAX ambient temperature: 40° C.
12) MAX external surface temperature: 90° C.
13) Don’t look directly the lamp trough the lens.
14) We recommend not to look at the lamp without wearing a proper protection; also ensure that the covers are assembled to
the equipment.
15) Inside the equipment there are high temperatures and tension/current values which might be very dangerous. It is
necessary to disconnect the equipment from the mains before removing its protection covers and wait for 30 minutes at least
before touching any part inside.
16) Do not switch on the equipment if its lamp is not inserted.
17) Leave sockets and air outlets free from encumbrances and clean them periodically (see “Maintenance” section).
18) Do not leave the packaging elements (polystyrene, nylon, metal parts, etc.) unattended; they might be dangerous for
children.
Pag. 2
http://www.coef.it
-
info@coef.it
This manual has been organized in order support the user, the installer or the maintenance operator of the described unit with those necessary informations for a correct use of the installation and working procedures of the
same unit.The various procedures will be just signalled by indicators (when necessary) evidencing the operation
dangers and the necessity of technical support.
Please find here below a list of symbols and relative meaning:
OPERATOR : Not particulary qualified staff, that can operate when no specific knowledge is required
COEF OPERATOR: Technical staff, qualified and trained by the constructor, for repair and extraordinary
operations.
MECHANICAL OPERATORS: Staff employed in the ordinary mechanical maintenance.
SPECIALIZED MECHANICAL OPERATOR: Qualified staff employed in extraordinary authorized installations and repair.
ELECTRIC OPERATORS: Staff employed in the ordinary electric maintenance.
SPECIALIZED ELECTRIC OPERATORS: Qualified staff employed in extraordinary authorized installations and repairs.
DANGER SIGNAL: Generic dager signal and electric shock danger signal.
GENERAL WARRANTY CONDITIONS
• The guarantee is valid for a period of 12 months from the date of purchase of the equipment.
• The parts which are proved to have manufacturing defects are also covered by the guarantee.
• The external parts of the equipment, its removable elements and lamps are excluded from the guarantee; for these
•
•
•
•
parts we recommend to follow the directions supplied by their manufacturers.
The guarantee is not valid in case of tampering or repairs carried out by non-authorized personnel.
The replacement of the equipment during the validity of the guarantee is not provided for.
The transport freights from and to the manufacturer for repairs under guarantee are at Customer’s charge.
When applying for the repair, always mention the serial number and the model of the equipment.
PACKING CONTENTS
Carefully check the contents of the packaging and the completeness of the components. If any of the parts listed hereunder is
missing, please contact your Dealer immediately:
•
•
•
•
•
•
•
MP700 Zoom complet unit.
This user manual.
2 quick lock/release (omega) brackets.
1 connector XLR 3 pin male.
1 connector XLR 3 pin female.
1 connector POWER.
1 safety-chain equipped with two snaps.
PROTECT NATURE.
DO NOT DISPOSE OF THE PACKAGING IN THE ENVIRONMENT.
CAREFULLY KEEP THE BOX AND THE COMPONENTS OF THE PACKAGING FOR ANY DISPLACEMENT
OR RE-SHIPMENT OF THE EQUIPMENT.
Do not leave the packaging elements (polystyrene, nylon, metal parts, etc.) unattended; they might be
dangerous for children.
http://www.coef.net - info@coef.it
Pag. 3
1.0 DIMENSIONS & POSITIONING
It is possible to set up the MP700 Zoom in any position.
2.0 TECHNICAL NOTES
MP700 Zoom with Magnetic Ballast
Code: 02E005
MP700 Zoom with Electronic Ballast
Code: 02E006
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Pag. 4
Lamp: MSR 700 SA 700W 54.000 lumen
16 bit movement resolution - PAN 540° / TILT 270°
PAN and TILT automatic repositioning
9 rotating gobos all interchangeable and indexable on 540°
Zoom linear motorized from 11° to 24° zoom possibility manteining a costant focus
Focus motorized
33 colors + white + bi-colors
Linear dimmer from 0 to 100%
Electronic dimmer of lamp from 100% to 50% (only electronic ballast version)
Shutter motorized
Iris motorized
Adjustable strobe
Rainbow effect adjustable in speed
Black light filter
Optical system with multilenses system
Linear frost
Rotating 3 faces prism adjustable in speed for both directions
Multifunction display
Remote reset via DMX
Remote On/Off lamp via DMX
Software upgrade via DMX (with UNI-PROG 8 Accessory)
Automatic fault survey
Automatic ventilation adjustment with internal temperature survey
Internal power factor correction
DMX 512 standard
Lamp lighted sensor
Over temperature protection
Absorbed power 230V.ca 50Hz 4,1A.
Weight: 37,5 Kg (with electronic Ballast 28,5 Kg.)
http://www.coef.it
-
info@coef.it
3.0
INSTALLATION
The constructor is not be considered responsible in case of:
•
•
•
•
•
•
•
•
•
Improper use fo the unit or use by not trained staff
Use in contrast with the directions on work safety
Wrong installation
Defective power supply
Serious lacks in the necessary maintenance
Unauthorized modifications and interventions
Use of spare parts that are not original or not specific for the unit
Total or partial inobservance of instructions
Unusual events
3.1 LAMP MOUNTING OR REPLACING
WARNING: read carefully
•
•
•
•
•
•
•
•
The unit mounts high pressure lamp.
The unit is realized to use only MSR700 lamp; absolutely don’t use other types of lamp.
The lamp must be changed if damaged or deformed by heat.
Switch off the projector before operating.
Wait at least 15 minutes after the projector has been switched off before operating again, in order to let it cool down
and avoid the lamp explosion.
Wear protection gloves and glasses.
Don’t look directly the lamp.
Read carefully the lamp builder’s instructions.
Wait 30 minutes in order to avoid burns.
Unscrew with a cross screwdriver the first screw A for a single turn; unscrew the second one completely B;
unscrew completely the screw A and to remove the cover that supports the lampholder.
Insert delicately the lamp in the projector support, driving it with the round cover.
Pay attention: the lampholder’s wires must correctly reenter in the projector. Block the cover screwing the screws
up ( part. A-B).
http://www.coef.net - info@coef.it
Pag. 5
3.2
VOLTAGE ADJUSTMENT
WARNING: switch off the projector before operating
Attention: the change of tension can be carried out on the model with Electronic Ballast only.
The tension value suitable for the projector is shown in a table
placed in the board of the base of the MP700 Zoom. A flag marks
the values preset for your equipment. It is possible to modify these
settings according to the country where the MP700 Zoom is going
to be installed (only for the model with Electronic Ballast) just by
shifting the cable with faston device (part. A) to the proper terminal
of the transformer which supplies the electronic card assembled
inside the base of the projector.
We recommend to update the serigraphy table with the new
value.
3.3
PROJECTOR INSTALLATION
To fix the MP 700 Zoom is necessary, when the installation has to be on a raised-from-the ground support, to
block the quick lock/release brackets of the unit by means of a screw provided with nut and locknut measuring not
less than M10X50, to insert in the central pre-arranged hole on the fixing bracket.
In addiction to the provided quick lock/release (omega) brackets, in order to guarantee a necessary security and
in respect of the actual safety rules concerning the projectors’ installation, it is compulsory to install a safety-chain,
equipped with two snaps, provided with the projector, to connect the MP 700 Zoom‘s body to the fixing structure.
ATTENTION: the safety chain, equipped with two snaps which can be hooked to the two pivots placed under the
base of the MP700 Zoom, (see part. A), must be properly installed and fixed to the supporting structure, in a way that
an incidental givin in of the main bracket would leed to the shortest possible fall of the projector. After such an intervention the safety-chain must be replaced with another original part.
ATTENTION: COEF is not responsible for installations not correctly made or made without respecting the
above indications: those installations are considered dangerous.
Pag. 6
http://www.coef.it
-
info@coef.it
4.0 - POWER SUPPLY CONNECTIONS
WARNING: In order to guarantee the utmost safety, connect the apparatus only to a properly
earthed mains system.
The projector is designed to work at the tension and frequency indicated by the electrical data label on the rear. Before connecting the projector to the mains, a qualified electrician must check its
conformity.
• The projector must be protect by an adeguated magneto-thermal switch .
• Don't power the unit with a dimmer circuit.
Power : indicated in the the serigraphy table (tollerance: +5% / -10%)
Should there be different electrical characteristics or special steps to be carried out, please contact COEF by
telephone or e-mail elettronica@coef.it
Supply the projector by connecting it as indicated in picture.
4.1 - DMX 512 CONNECTIONS
Connect the projector and the control unit to a wire in conformity with the EIA RS-485 standards: braided bipolar,
shielded, 120 ohm of characteristic impedance, 22-24 AWG, equipped with Cannon 3 Pin XRL plugs. Respect the
DMX 512 signal input and output according to the panel indications. A terminal pin with 120 ohm resistance (¼ Watt
minimum) must be inserted between the terminals 2 and 3 in the last piece of apparatus.
http://www.coef.net - info@coef.it
Pag. 7
5.0
SPECIAL FUNCTIONS AND PROJECTOR ASSIGNMENT
On the front panel of MP700 Zoom you'll find a section for
the additional functions and for setting the projector.
Following the picture, you can see all the offered possibilities in detail.
All operations are to be carried out with the E, F, G, H buttons, respectively indicated as MENU, ENTER, DOWN and
UP.
The display D will inform you about the selected functions.
The 3 A, B, and C leds will allow you to know:
A = reception of the DMX line.
B = lamp ON.
C = errors indicated on the ERR table (see table 6.0).
On switching the projector on, the display will indicate the type of projector and the version of control software
which have been installed. To this purpose, please remember that this type of projector belongs to a new generation
of projectors, designed with the possibility of updating the software version through the normal DMX connection by
means of a programmer deliberately created: UNI-PROG 8.
After the indication MSTR HOME, the projector carries out the RESET and gets ready to be controlled from the
connected console.
The display will indicate 1 as default value. This means that the first channel occupied by the projector will respond to the values sent to channel 1 by the DMX line. This enables us to make MP700 Zoom (which we are installing) completely independent from control or integral with any other installed projector.
General Rules:
Refer to the Table of Section 6.0 in the following page.
By each pressure, Button MENU (E) permits to go backwards by one level.
G and H (DOWN and UP) buttons select functions and sub-functions.
Button F (ENTER) enters the function and confirms a control.
By pressing Button MENU (E) and buttons UP and DOWN (H and G) you can select the menu you have to modify.
Once the wished menu is reached, press Button F (ENTER) to confirm your selection and enter the function.
Press G or H to enter the sub-functions if available.
Always confirm your selection with ENTER.
Press MENU to go out of the function and press again to go back to the starting level.
Example: We installed our projector on the ceiling and for this reason we want the visualization of the display to
be correct.
Press MENU
Press H (UP) 11 times up to “MISC”
Press ENTER the Display will show “RSET”
Press H (UP) twice up to “DSPL”
Press ENTER the Display will show “ONOF”
Press H (UP) once up to “STRV”
Press ENTER the Display will show “STND”; this is the actual configuration state.
Press H (UP) once up to R.E.V..; the blinking point indicate the available configuration.
Press ENTER ...... The Display visualization as been rotated to 180°.
Press MENU 4 times to return to starting MENU.
The indication of the display will automatically come back after 120 sec. and inform on the set starting channel
DMX. If we are now in a sub-function, this automatic device will not assume control.
Pag. 8
http://www.coef.it
-
info@coef.it
6.0 MENU, FUNCTION & SUB-FUNCTIONS
MENU
FUNCTION
DMX
1/498 Magnetic
1/497 Electronic
LAMP
TIME
MACH
SUB-FUNCTION
(*) = default value - factory assigned
DESCRIPTION
DMX start channel
Lamp working hours (KH=thousands H=hours)
Lamp working hours reset (confirm by ENTER)
Projector working hours (KH=thousands H=hours)
SHOW - KH, H
RST - GO?
SHOW - KH, H
ERR
E OK
E110
E220
E230
E240
E250
E260
E420
E510
E520
W310
W410
W422
No error
EEPROM failure
Malfunction of the COLOR motor/sensor
Malfunction of the GOBOS motor/sensor
Malfunction of the GOBOS ROT. motor/sensor
Malfunction of the PAN motor/sensor
Malfunction of the TILT motor/sensor
No ignition of the lamp beyond 3 attempts. (break?)
Malfunction encoder PAN
Malfunction encoder TILT
Checksum Setup not valid
Lamp working hours for more than 500 hours
LAMP start beyond 1 attempts (attempt to warmth or exausted lamp)
SHUT
HOME
TEST
ADJ
SET
HOME SHUTTER
TEST SHUTTER
Fine regulation of the closing shutter.
Reserved
COL
HOME
TEST
CSHUT
MODE
ADJ
P1
(*) OFF / ON
(*) MOD1 / MOD2
P 1 / P20
- 49 / 49
-29 / 29
HOME COLOR
TEST COLOR
Color change in black-out position
Color switching or linear wheel motion
Fine regulation of the COLOR position (P1 / P20)
-29 / 29
HOME GOBOS
TEST GOBOS
GOBO change in black-out position
Fine regulation of the NEUTRAL GOBO position
GOBO
HOME
TEST
GSHUT
ADJ
RGOB
HOME
TEST
HOME Rotation GOBOS
TEST Rotation GOBOS
CONV
HOME
TEST
ADJ
HOME Conversion filters
TEST Conversion filters
Fine regulation of the CONVERSION FILTER position
(*) OFF / ON
P1
P1
-99 / 99
FCUS
HOME
TEST
HOME Focus trolley
TEST Focus trolley
ZOOM
HOME
TEST
HOME ZOOM trolley
TEST ZOOM trolley
EFCT
HOME
TEST
ADJ
HOME Prism/Frost
TEST Prism/Frost
Fine regulation of the PRISM position
RPRS
TEST
TEST of the Prism rotation
IRIS
HOME
TEST
HOME Iris
TEST Iris
PAN
HOME
TEST
STRV
ENCO
(*) STND / REV
(*) ON / OFF
HOME PAN movement
TEST PAN movement
Switch movement direction ( DX / SX)
ON/OFF the automatic repositioning of the PAN
TILT
HOME
TEST
STRV
ENCO
(*) STND / REV
(*) ON / OFF
HOME TILT movement
TEST TILT movement
Switch movement direction (UP / DOWN)
ON/OFF the automatic repositioning of the TILT
SCH
CH1 / CH14 (CH15)
CH15 = Electronic Ballast only
DMX value for the indicated channel
LAMP
ONOF
CDMX
(*) ON / OFF/ AUTO
(*) NO / YES
Lamp ON / Lamp OFF / LAMP OFF after 1 hour of no change on DMX
LAMP switching on by DMX control
(*) YES / NO
(*) ON / OFF
(*) STND / REV
(*) STND / SWAP
YES / NO
(automatic value)
MASTER HOME (Starting RESET)
MASTER HOME via DMX control
Display on / Display off
180° rotation of the visualization display
Channel control switch PAN / TILT
YES = Electronic Dimmer ON (Can. 15 / Electronic Ballast)
Show the installed software version
RSET
RDMX
DSPL
MISC
SWPT
EDIM
VER
P1
-99 / 35
http://www.coef.net - info@coef.it
Pag. 9
7.0
CHANNELS AND DIGITAL VALUES
CH
1
2
MODE1
2
MODE2
3
SHUTTER / STROBE / DIMMER
0-5
SHUTTER closed
6-100
DIMMER from channel 14 value
101-110 DIMMER 0 > 100% Automatic 6 sec.
111-120 DIMMER 100% > 0 Automatic 6 sec.
121-126 DIMMER 0 > 100%
slow
Faster shut down
127-132 DIMMER 0 > 100%
middle
Faster shut down
133-138 DIMMER 0 > 100%
fast
Faster shut down
139-144 DIMMER 100% > 0
slow
Faster open
145-150 DIMMER 100% > 0
middle
Faster open
151-156
157-162
163-168
169-174
175-180
181-186
187-192
193-250
251-255
DIMMER 100% > 0
fast
DIMMER 0 > 100% > 0 slow
DIMMER 0 > 100% > 0 middle
DIMMER 0 > 100% > 0 fast
Strobe lamp from 1 to 6 random
Strobe lamp from 1 to 6 random
Strobe lamp from 1 to 6 random
STROBE Speed adjustment
SHUTTER open
COLOR MODE 1
0-5
Neutral
6 - 15
Yellow
16 - 25
Blue
26 - 35
Magenta
36 - 45
Green light
46 - 55
Orange
56 - 65
Cyano
66 - 75
Pink
76 - 85
Red
86 - 95
Blu light
96 - 105
Green
106 - 115 Wood
116 - 125
126 - 135
136 - 145
146 - 155
156 - 165
166 - 175
176 - 185
186 - 195
196 - 200
201 - 205
206 - 230
231 - 255
White-Yellow
Yellow-Blue
Blue-Magenta
Green light-Orange
Orange-Cyano
Cyano-Pink
Red-Blue light
Blue light-Green
Random full-color (slow)
Random full-color (fast)
CW Rotation adjustment
CCW Rotation adjustment
COLOR MODE 2
0-5
Neutral
6 - 10
Yellow
11 - 15
Blue
16 - 20
Magenta
21 - 25
Green light
26 - 30
Orange
31 - 35
Cyano
36 - 40
Pink
41 - 45
Red
46 - 50
Blu light
51 - 55
56 - 60
61 - 180
181 - 185
186 - 190
191 - 195
196 - 200
201 - 215
216 - 235
236 - 255
Green
Wood
Positioning
Random fast
Random middle
Random slow
Random very slow
Random very fast
CW Rotation adjustment
CCW Rotation adjustment
GOBOS
0 - 10
1 1- 20
21 - 30
31 - 40
41 - 50
51 - 60
61 - 70
71 - 80
81 - 90
91 - 100
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
161 - 170
171 - 180
181 - 190
191 - 198
199 - 205
206 - 230
231 - 255
GOBO 2 chann.4 controls position
GOBO 3 chann.4 controls position
GOBO 4 chann.4 controls position
GOBO 5 chann.4 controls position
GOBO 6 chann.4 controls position
GOBO 7 chann.4 controls position
GOBO 8 chann.4 controls position
GOBO 9 chann.4 controls position
GOBOS Random fast
GOBOS Random slow
CW Rotation adjustment
CWW Rotation adjustment
Neutral
GOBO 1
GOBO 2
GOBO 3
GOBO 4
GOBO 5
GOBO 6
GOBO 7
GOBO 8
GOBO 9
GOBO 1
chann.4
chann.4
chann.4
chann.4
chann.4
chann.4
chann.4
chann.4
chann.4
chann.4
controls rotation
controls rotation
controls rotation
controls rotation
controls rotation
controls rotation
controls rotation
controls rotation
controls rotation
controls position
4
ROTATION GOBOS
0-5
STOP
6 - 255
From 0 to 540° GOBO positioning
6 - 130
CW Rotation adjustment of the GOBO
131 - 255 CWW Rotation adjustment of the GOBO
5
PAN MOVEMENT
6
PAN MOVEMENT FINE ADJUSTMENT
7
TILT MOVEMENT
8
TILT MOVEMENT FINE ADJUSTMENT
9
COLOR FILTER CONVERSION
0 - 79
Neutral
80 - 169
Conversion 3400°K
170 - 255 Conversion 5600°K
10
FOCUS ADJUSTMENT
0 - 255
Linear FOCUS adjustment
11
LINEAR ZOOM ADJUSTEMT
0 - 255
Linear ZOOM adjustment
Pag. 10
http://www.coef.it
-
info@coef.it
Faster open
[reg. 0.0-0.5 sec.]
[reg. 0.6-1.5 sec.]
[reg. 1.6-2.5 sec.]
CH
12
EFFECTS (Frost - Prism)
0-5
Neutral
6 - 20
Automatic FROST from 0 to 100% (velocity adjustment)
21 - 40
Automatic FROST from 100% to 0 (velocity adjustment)
41 - 60
Frost
61 - 80
Prism 3 faceted
81 - 170
CW PRISM rotation with velocity adjustment
171 - 255 CWW PRISM rotation with velocity adjustment
13
IRIS
0-5
6 - 130
131 - 150
151 - 170
171 - 190
191 - 210
211 - 230
321 - 250
251 - 255
Open / Neutral
IRIS with manual regolation (100% - 0)
IRIS closed
IRIS 0 - 100%
IRIS 100% - 0
IRIS 0-100%-0 slow
IRIS 0-100%-0 middle
IRIS 0-100%-0 fast
IRIS 0-100%-0 random
DIMMER
0-5
6 - 250
251 - 255
DIMMER Closed
DIMMER regolation
DIMMER Open
14
WARNING: position CHANNEL 1 at a value between 6 and 100, in order to control DIMMER with this channel.
15
DIMMER Electronic (only Electronic Ballast Code: 02E006)
0-5
Light at 50%
6 - 250
Light from 50% to 100%
251 - 255 Light at 100%
7.1 SPECIAL ACTION
When the lamp control via DMX (CDMX) and the reset via DMX (RDMX) function
have been activated in the configuration menu, it’s possible, by a combination of
the channels values, to control the lamp switch ON/OFF or to allow the projector
MASTER RESET.
Lamp ON via DMX:
CHANNEL 2 = value 0
CHANNEL 3 and CHANNEL 4 = value 0 > 255 > 0
Lamp OFF via DMX:
CHANNEL 2 = value 255
CHANNEL 3 and CHANNEL 4 = value 0 > 255 > 0
MASTER RESET:
CHANNEL 1 = value 0
CHANNEL 2 and CHANNEL 3 = value 0 > 255 > 0
http://www.coef.net - info@coef.it
Pag. 11
8.0
LAMP ADJUSTMENT
• Don’t look directly the beam trough the lens.
• The lamp is pre-regulated by the factory.
Only fine-adjustment. Don’t move the screws
”C” up to upper or lower extremities.
Lamp adjustment is necessary to obtain a uniform and powerful
light beam. Switch on the projector and set the channels without
gobo and colors. Adjust the three screws C until you reach the
ideal condition between power and homogeneity.
9.0 GOBOS REPLACEMENT
WARNING: switch off the projector before operating
Open the cover of MP700 Zoom by the 4 fast screw.
The gobo-wheel of the MP 700 Zoom contains dichroic gobos. They are interchangeable simply by removing the little elastic ring with a screwdriver (see figure).
In order to replace a dichroic gobo with a steel gobo,
put a thick ring between the gobo and the elastic ring.
Insert the chosen gobo and place again the steel
ring, paying attention that it reaches its correct position.
Pag. 12
http://www.coef.it
-
info@coef.it
10.0
ORDINARY MAINTENANCE
Ordinary maintenance on the projectors MP 700 Zoom is necessary to maintain the perfect efficiency of the unit and to avoid defects like the low luminosity of the light beam or the elevated
overheating of the equipment.
In the figures you can see
those components that can easily
accumulate dust and grease.
Clean them using a soft cloth and
common glass-cleaners.
10.1
EXTRAORDINARY MAINTENANCE
WARNING: switch off the projector before operating
To make an extraordinary maintenance, it is
necessary the presence of a generic or qualified
mechanical operator, according to the type of the
needed intervention. In order to make its use
easier, we advise you to completely draw out the
mechanic unit of the zoom and focus movements
as follows: disconnect the two motors (connectors
B and C) and the fan (connector D); remove the 4
screws (part. A) and
carefully extract the whole
mechanic unit. Clean carefully the indicated parts.
Once the frame with the Zoom/Focus mechanic unit has
been removed, it is possible to clean the parts which are usually
difficult to reach. Reassemble the Zoom/Focus unit carefully,
being sure in particular that the blade with prism and frost is
positioned between the two lenses of the Zoom/Focus unit.
Remember then to connect again the 2 motors and the fan to
their connectors.
http://www.coef.net - info@coef.it
Pag. 13
You must particularly take care of the sensors which are really fundamental in the unit working.
The sensors are absolutely necessary when a general reset of the projector is needed. If this function is not correctly executed, it will totally compromise the regular working of the projector, at least for the group referred to the
sensor itself.
The sensors of the encoders concerning the PAN and TILT movements are located in the base and in the arm of
the MP700 Zoom respectively. The pictures clearly show how you can reach these components and where you can
correctly operate for their maintenance.
Another place where grease and dust settle is inside the lamp-box. Carry out the following operations in order to
clean: unscrew, but not completely, the 4 screws on the side of the fin unit located on top of the bulb; draw out the full
fin unit; clean the antiheat filter and the parabola of the bulb; assemble the fin unit again by inserting first the part next
to the lamp-board and then the 4 screws in their seat; tighten carefully.
Pag. 14
http://www.coef.it
-
info@coef.it
10.2 ELETTRONIC MAINTENANCE
WARNING: switch off the projector before operating
This section is dedicated in detail to the electronic connections between the card and the mechanical components, assembled in the projector. These informations will be absolutely necessary when
the mechanical unit has to be removed from the projector for maintenance and/or repair.
The connections are made using handy connectors and are detailed in figure where you can find indications
about the connection between a specific connector and a specific component of the mechanical unit. This includes
the motors and the sensors of the various effects wheels ( color, gobos, prisms, shutter etc.).
WARNING! An improper use of this documentation made by not specifically qualified staff can damage
irremediably the electronic and/or mechanical components of the projector.
1
Motor SHUTTER / STROBE
15
Sensor PAN
2
Motor COLORE wheel
16
Sensor TILT
3
Motor GOBOS wheel
17
S1
Sensor COLOR wheel
4
Motor GOBOS Rotation
18
S2
Sensor GOBOS wheel
5
Motor EFFECTS wheel
19
S3
Sensor GOBOS Rotation
6
Motor ZOOM
20
ON/OFF Lamp (only Magnetic Ballast version)
7
Motor FOCUS
21
Electronic Ballast connector
8
Motor CONVERSION FILTERS
22
LIGHT Sensor / NTC Sensor
9
Motor IRIS
23
POWER Connector
10
Motor PRISM Rotation
24
Faston GROUND connection
11
Motor TILT
25
DMX IN/OUT
12
Motor PAN
26
Head FAN
13
Encoder TILT
27
Base FAN
14
Encoder PAN
http://www.coef.net - info@coef.it
Pag. 15
11.0
TROUBLESHOOTING
PROBLEM
The projector doesn’t swich on
CAUSE
ACTION
- The power supply is not present
Check if the luminous indicator is lighted
or not.
- The lamp is not working
Replace the lamp.
- The thermal switch is active
Just to wait for little of time.
The projector swiches on but - Wrong DMX configuration
doesn’t answer to commands
Defecting projection
Make sure that the projector is correctly
configurated.
- Defective cables
Replace or repair the DMX cable.
- LED A is off
Check the control unit & DMX cable.
- Defective control unit
Check the control unit by means of other
working projectors.
Technical aid is required.
- The lens is broken
Check that the lens are not broken.
- Dust or grease stored on the all Remove dust or grease stored on lenses.
parts of projector
Projection with halo
- Dust or grease stored on the all Carefully clean the optical group lenses
parts of projector
and the projector components (see “Maintenance” chapter).
Carefully clean the optical group lenses
The color or other effects doesn’t - Position sensor dirty with dust or and the projector components (see “Maincoincide to the selected value.
grease
tenance”).
- Defective motor
- Electronic board
Technical aid is required.
Carefully clean the optical group lenses
and the projector components (see “Maintenance”).
The PAN or TILT movement - Defective motor
doesn’t coincide to the selcted - Electronic board
value
Technical aid is required.
The projector does not carry out - ENCO off in the PAN/TILT confi- Set ON ENCO Function of PAN/TILT conthe automatic repositioning of the guration menu (cap. 6.0)
figuration menu (cap. 6.0).
PAN or TILT movements.
Pag. 16
http://www.coef.it
-
info@coef.it