Switching Quick Charger
C-510
Switching Quick Charger
C-510
USER MANUAL
USER MANUAL
Congratulations to your purchase of the PowerBase Switching Quick Charger
C-511and batteries. This manual will help you understand how to operate this
Charger and Batteries properly.
Congratulations to your purchase of the PowerBase Switching Quick Charger
C-511and batteries. This manual will help you understand how to operate this
Charger and Batteries properly.
Instructions for Use
Instructions for Use
1) Auto Voltage switching 100~240V, international use.
2) Place 2 or 4, AA or A AA size batteries into the battery compartment.
Batteries must be inserted properly for good electrical contact
and correct polarity direction.
3) Plug the charger into the wall AC outlet. The red LED indicator
light will glow to indicate a normal charging mode.
4) C-511 charger is designed to charge 2 or 4 AA/AAA size Ni-MH batteries.
Please refer to the combinations below.
5) Indications of RED and GREEN LED Light.
Red LED Light - will turn on to indicate the charger is charging the batteries.
Green LED Light - will turn on when the batteries are fully charged and cut off
by 8 hours timer cut-off device.
1) Auto Voltage switching 100~240V, international use.
2) Place 2 or 4, AA or A AA size batteries into the battery compartment.
Batteries must be inserted properly for good electrical contact
and correct polarity direction.
3) Plug the charger into the wall AC outlet. The red LED indicator
light will glow to indicate a normal charging mode.
4) C-511 charger is designed to charge 2 or 4 AA/AAA size Ni-MH batteries.
Please refer to the combinations below.
5) Indications of RED and GREEN LED Light.
Red LED Light - will turn on to indicate the charger is charging the batteries.
Green LED Light - will turn on when the batteries are fully charged and cut off
by 8 hours timer cut-off device.
(1) For 2 or 4 AA size Ni-MH Cells
(1) For 2 or 4 AA size Ni-MH Cells
(2) For 2 or 4 AAA size Ni-MH Cells
(2) For 2 or 4 AAA size Ni-MH Cells
NOTE: Never put Ni-MH and Ni-Cd batteries together in the
PowerBase Charger.
NOTE: Never put Ni-MH and Ni-Cd batteries together in the
PowerBase Charger.
CAUTION
CAUTION
1. Do NOT recharge Ni-Mh & Ni-Cd rechargeable batteries at the same time.
2. This product is designed for Ni-Mh/Ni-Cd rechargeable batteries only.
To avoid personal injury and damage, do not charge any
primary alkaline, zinc chloride, or zinc carbon type batteries.
3. Do not expose the charger to rain or moisture.
4. Do not operate the charger using an extension cord.
5. Do not use the charger if it has received a sharp blow, been dropped,
Or damaged in anyhow.
6. To reduce risk of shock, disconnect the AC power source (AC adaptor)
from outlet before attempting any cleaning of the charger.
7. Do not charge a leaking, corroded or dead battery.
8. Do not attempt to repair charger by yourself. When service or repair is
required, contact qualified service personnel.
9. Do not try to disassemble the charger.
10. Store the charger in a cool and dry place when not in use. Keep
away from children.
1. Do NOT recharge Ni-Mh & Ni-Cd rechargeable batteries at the same time.
2. This product is designed for Ni-Mh/Ni-Cd rechargeable batteries only.
To avoid personal injury and damage, do not charge any
primary alkaline, zinc chloride, or zinc carbon type batteries.
3. Do not expose the charger to rain or moisture.
4. Do not operate the charger using an extension cord.
5. Do not use the charger if it has received a sharp blow, been dropped,
Or damaged in anyhow.
6. To reduce risk of shock, disconnect the AC power source (AC adaptor)
from outlet before attempting any cleaning of the charger.
7. Do not charge a leaking, corroded or dead battery.
8. Do not attempt to repair charger by yourself. When service or repair is
required, contact qualified service personnel.
9. Do not try to disassemble the charger.
10. Store the charger in a cool and dry place when not in use. Keep
away from children.
PLEASE NOTE:
PLEASE NOTE:
*PowerBase Industrial (HK) Ltd. will not be responsible for any
personnel loss and/or injury if the defect was caused by misuse or
mishandling by the user in any way.
*PowerBase Industrial (HK) Ltd. will not be responsible for any
personnel loss and/or injury if the defect was caused by misuse or
mishandling by the user in any way.
CHARGER SPECIFICATION :
CHARGER SPECIFICATION :
International Voltage
Battery Type / Size
Charging Current
Time Pratectich
Switching : 100~240V 50~60Hz
(UL, VDE)
Ni-MH AA & AAA Batteries
330mA / AA
160mA / AAA
8 hours timer cut-off device
International Voltage
Battery Type / Size
Charging Current
Time Pratectich
Switching : 100~240V 50~60Hz
(UL, VDE)
Ni-MH AA & AAA Batteries
330mA / AA
160mA / AAA
8 hours timer cut-off device