Owner`s Manual - Fondriest Environmental

GPSMAP 500/700 Series and echoMAP 50/70
Series
™
®
Owner’s Manual
December 2013
190-01556-10_0B
Printed in Taiwan
All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the
right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such
changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product.
Garmin®, the Garmin logo, BlueChart®, g2 Vision®, GPSMAP®, and MapSource® are trademarks of Garmin Ltd.‍ or its subsidiaries, registered in the USA
and other countries.‍ echoMAP™, GMR™, GXM™, HomePort™, LakeVü™, and Meteor™ are trademarks of Garmin Ltd.‍ or its subsidiaries.‍ These trademarks
may not be used without the express permission of Garmin.‍
Android™ is a trademark of Google Inc.‍ The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.‍ and any use of such marks by Garmin is
under license.‍ FUSION-Link™ is a trademark of Fusion Electronics Ltd.‍ iOS® is a registered trademark of Cisco Systems, Inc.‍ used under license by Apple
Inc.‍ iPod® is a trademark of Apple Inc.‍, registered in the U.‍S.‍ and other countries.‍ microSD™ and the microSDHC logo are trademarks of SD-3C, LLC.‍
NMEA®, NMEA 2000®, and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association.‍ SiriusXM® is a registered
trademark of SiriusXM Radio Inc.‍ Wi-Fi® is a registered trademark of W-Fi Alliance.‍ Windows® is a registered trademark of Microsoft Corporation in the
United States and other countries.‍ Other trademarks and trade names are those of their respective owners.‍
Table of Contents
Introduction.................................................................... 1
Device Views ............................................................................ 1
echoMAP 70 Series and GPSMAP 700 Series ..................... 1
Using the Touchscreen .................................................... 1
echoMAP 50 Series and GPSMAP 500 Series ..................... 1
Device Keys ..................................................................... 1
Tips and Shortcuts ..................................................................... 1
Downloading the Manuals .......................................................... 1
Manual Conventions .................................................................. 1
GPS Satellite Signals ................................................................. 1
Adjusting the Backlight ............................................................... 1
Adjusting the Color Mode ........................................................... 1
Customizing the Home Screen .................................................. 2
Inserting Memory Cards ............................................................. 2
Charts and 3D Chart Views ........................................... 2
Navigation Chart and Offshore Fishing Chart ............................ 2
Zooming In and Out of the Chart ........................................... 2
Panning the Chart ................................................................. 2
Selecting an Item on the Map Using the Device Keys .......... 2
Chart Symbols ....................................................................... 2
Navigating to a Point on the Chart ........................................ 3
Viewing Location and Object Information on a Chart ............ 3
Viewing Details about Navaids .............................................. 3
Selecting a Map .................................................................... 3
Premium Charts .................................................................... 3
Viewing Tide Station Information ...................................... 3
Showing Satellite Imagery on the Navigation Chart ......... 4
Viewing Aerial Photos of Landmarks ................................ 4
Automatic Identification System ................................................. 4
AIS Targeting Symbols ......................................................... 4
Heading and Projected Course of Activated AIS Targets ..... 4
Showing AIS Vessels on a Chart or 3D Chart View .............. 5
Activating a Target for an AIS Vessel ................................... 5
Viewing Information about a Targeted AIS Vessel ........... 5
Deactivating a Target for an AIS Vessel .......................... 5
Viewing a List of AIS Threats ................................................ 5
Setting the Safe-Zone Collision Alarm .................................. 5
AIS Distress Signals .............................................................. 5
Navigating to a Distress Signal Transmission .................. 5
AIS Distress Signal Device Targeting Symbols ................ 5
Enabling AIS Transmission Test Alerts ............................ 5
Turning Off AIS Reception .................................................... 5
Chart and 3D Chart View Settings ............................................. 6
Navigation and Fishing Chart Setup ..................................... 6
Waypoints and Tracks Settings on the Charts and Chart
Views ..................................................................................... 6
Laylines Settings ................................................................... 6
Overlay Numbers Settings .................................................... 6
Editing the Data Fields ..................................................... 6
Showing a Navigation Inset ................................................... 6
Chart Appearance Settings ................................................... 6
Setting the Heading and Course Over Ground Lines ............ 7
Other Vessels Settings on the Charts and Chart Views ........ 7
AIS Display Settings ......................................................... 7
Fish Eye 3D Settings ............................................................. 7
Navigation with a Chartplotter...................................... 7
Basic Navigation Questions ....................................................... 8
Destinations ............................................................................... 8
Searching for a Destination by Name ................................... 8
Selecting a Destination Using the Navigation Chart ............. 8
Searching for a Destination Using Nav Info .......................... 8
Searching for a Marine Services Destination ........................ 8
Courses ...................................................................................... 8
Table of Contents
Setting and Following a Direct Course Using Go To ............. 8
Setting and Following a Course Using Auto Guidance ......... 8
Autopilot Navigation .............................................................. 9
Stopping Navigation ................................................................... 9
Waypoints .................................................................................. 9
Marking Your Present Location as a Waypoint ..................... 9
Creating a Waypoint at a Different Location ......................... 9
Marking and Starting Navigation to an MOB Location .......... 9
Viewing a List of all Waypoints .............................................. 9
Editing a Saved Waypoint ..................................................... 9
Moving a Saved Waypoint .................................................... 9
Browsing for and Navigating to a Saved Waypoint ............... 9
Deleting a Waypoint or an MOB ............................................ 9
Deleting All Waypoints .......................................................... 9
Routes ........................................................................................ 9
Creating and Navigating a Route From Your Present
Location ................................................................................. 9
Creating and Saving a Route .............................................. 10
Viewing a List of Routes ...................................................... 10
Editing a Saved Route ........................................................ 10
Browsing for and Navigating a Saved Route ...................... 10
Browsing for and Navigating Parallel to a Saved Route ..... 10
Deleting a Saved Route ...................................................... 10
Deleting All Saved Routes .................................................. 10
Tracks ...................................................................................... 10
Showing Tracks ................................................................... 10
Setting the Color of the Active Track ................................... 10
Saving the Active Track ...................................................... 10
Viewing a List of Saved Tracks ........................................... 10
Editing a Saved Track ......................................................... 10
Saving a Track as a Route .................................................. 11
Browsing for and Navigating a Recorded Track .................. 11
Deleting a Saved Track ....................................................... 11
Deleting All Saved Tracks ................................................... 11
Retracing the Active Track .................................................. 11
Clearing the Active Track .................................................... 11
Managing the Track Log Memory During Recording .......... 11
Configuring the Recording Interval of the Track Log ........... 11
Deleting All Saved Waypoints, Routes, and Tracks ................. 11
Combinations............................................................... 11
Selecting a Combination .......................................................... 11
Customizing a Combination Screen ......................................... 11
Creating a Custom Combination Screen ................................. 11
Gauges and Almanac Information.............................. 11
Viewing the Compass .............................................................. 11
Viewing Trip Gauges ................................................................ 12
Resetting Trip Gauges ........................................................ 12
Viewing Engine and Fuel Gauges ............................................ 12
Customizing Engine Gauge and Fuel Gauge Limits ........... 12
Enabling Status Alarms for Engine Gauges ........................ 12
Enabling Some Engine Gauge Status Alarms .................... 12
Selecting the Number of Engines Shown in Gauges .......... 12
Customizing the Engines Shown in Gauges ....................... 12
Configuring the Fuel Gauges Display ................................. 12
Setting the Fuel Capacity of the Vessel .............................. 12
Synchronizing the Fuel Data with the Actual Vessel Fuel ... 12
Setting the Fuel Alarm ......................................................... 12
Viewing the Wind Gauges ........................................................ 12
Configuring the Speed Source ............................................ 12
Configuring the Heading Source of the Wind Gauge .......... 13
Selecting the Range of the Close-Hauled Wind Gauge ...... 13
Viewing the Environment Gauges ............................................ 13
Configuring the Alignment of the Wind Gauge .................... 13
Configuring the Heading Source of the Environment
Gauge ................................................................................. 13
i
Setting the Barometer Reference Time ............................... 13
Tide, Current, and Celestial Information .................................. 13
Tide Station Information ...................................................... 13
Current Station Information ................................................. 13
Celestial Information ........................................................... 13
Viewing Tide Station, Current Station, or Celestial
Information for a Different Date ........................................... 13
Viewing Information for a Different Tide or Current Station 13
Viewing Almanac Information from the Navigation Chart .... 13
Sonar............................................................................. 13
Sonar Views ............................................................................. 13
Full-Screen Sonar View ...................................................... 14
DownVü Sonar View ........................................................... 14
SideVü Sonar View ............................................................. 14
SideVü/DownVü Scanning Technology .......................... 14
Split-Zoom Sonar View ....................................................... 14
Split-Frequency Sonar View ................................................ 14
Pausing the Sonar Display ....................................................... 14
Creating a Waypoint on the Sonar Screen .............................. 14
Viewing Sonar History .............................................................. 14
Adjusting the Level of Detail .................................................... 14
Adjusting the Color Intensity .................................................... 14
Adjusting the Range of the Depth or Width Scale .................... 15
Setting the Zoom Level on the Sonar Screen .......................... 15
Sonar Frequencies ................................................................... 15
Selecting Frequencies ......................................................... 15
Creating a Frequency Preset .............................................. 15
Turning On the A-Scope .......................................................... 15
Selecting the Transducer Type ................................................ 15
Sonar Setup ............................................................................ 16
Sonar Settings ..................................................................... 16
Sonar Appearance Settings ................................................ 16
Advanced Sonar Settings .................................................... 16
Sonar Installation Settings .................................................. 16
Sonar Alarm Settings .......................................................... 16
Sonar Recordings .................................................................... 16
Recording the Sonar Display .............................................. 16
Stopping the Sonar Recording ............................................ 16
Deleting a Sonar Recording ................................................ 16
Depth and Water Temperature Graphs ................................... 16
Setting the Depth and Water Temperature Graph Range and
Time Scales ........................................................................ 17
Radar............................................................................. 17
Radar Display Modes ............................................................... 17
Transmitting Radar Signals ...................................................... 17
Range of Radar Signals ...................................................... 17
Adjusting the Zoom Scale on the Radar Screen ...................... 17
Tips for Selecting a Radar Zoom Scale .............................. 17
Sentry Mode ............................................................................. 17
Enabling Timed Transmit .................................................... 17
Setting the Standby and Transmit Times ............................ 18
Enabling a Guard Zone ....................................................... 18
Defining a Circular Guard Zone .......................................... 18
Defining a Partial Guard Zone ............................................. 18
Marking a Waypoint on the Radar Screen .......................... 18
Viewing a List of AIS Threats .............................................. 18
Showing AIS Vessels on the Radar Screen ........................ 18
VRM and EBL .......................................................................... 18
Showing the VRM and the EBL ........................................... 18
Adjusting the VRM and the EBL .......................................... 18
Measuring the Range and Bearing to a Target Object ........ 18
Radar Overlay .......................................................................... 18
Radar Overlay and Chart Data Alignment ........................... 19
Showing the Radar Overlay ................................................ 19
Stopping the Transmission of Radar Signals ........................... 19
ii
Optimizing the Radar Display .................................................. 19
Radar Gain and Clutter ....................................................... 19
Adjusting Gain on the Radar Screen Automatically ....... 19
Adjusting Gain on the Radar Screen Manually .............. 19
Minimizing Nearby Large-Object Interference ................ 19
Minimizing Side-Lobe Interference on the Radar
Screen ............................................................................ 19
Adjusting Sea Clutter on the Radar Screen
Automatically .................................................................. 19
Adjusting Sea Clutter on the Radar Screen Manually .... 19
Adjusting Rain Clutter on the Radar Screen .................. 20
Reducing Cross Talk Clutter on the Radar Screen ........ 20
Radar Display Settings ........................................................ 20
Radar Appearance Settings ................................................ 20
Front-of-Boat Offset ............................................................ 20
Measuring the Potential Front-of-Boat Offset ................. 20
Setting the Front-of-Boat Offset ..................................... 20
Digital Selective Calling.............................................. 20
Networked Chartplotter and VHF Radio Functionality ............. 20
Turning On DSC ...................................................................... 20
DSC List ................................................................................... 20
Viewing the DSC List .......................................................... 20
Adding a DSC Contact ........................................................ 21
Incoming Distress Calls ........................................................... 21
Navigating to a Vessel in Distress ....................................... 21
Man-Overboard Distress Calls Initiated from a VHF Radio . 21
Man-Overboard Distress Calls Initiated from the
Chartplotter ......................................................................... 21
Position Tracking ..................................................................... 21
Viewing a Position Report ................................................... 21
Navigating to a Tracked Vessel .......................................... 21
Creating a Waypoint at the Position of a Tracked Vessel ... 21
Editing Information in a Position Report .............................. 21
Deleting a Position-Report Call ........................................... 21
Viewing Vessel Trails on the Chart ..................................... 21
Individual Routine Calls ........................................................... 21
Selecting a DSC Channel ................................................... 21
Making an Individual Routine Call ....................................... 22
Making an Individual Routine Call to an AIS Target ............ 22
Media Player................................................................. 22
Opening the Media Player ....................................................... 22
Selecting the Media Source ..................................................... 22
Connecting a Bluetooth® Wireless Device to the Meteor
Media Player ....................................................................... 22
Browsing for Music .............................................................. 22
Enabling Alphabetical Search ........................................ 22
Setting a Song to Repeat ............................................... 22
Setting a Song to Repeat .................................................... 22
Setting All Songs to Repeat ................................................ 22
Setting Songs to Shuffle ...................................................... 22
Listening to the Radio ......................................................... 22
Saving a Channel as a Preset ........................................ 22
Removing a Channel Preset .......................................... 22
Changing the Tuning Mode ............................................ 22
Setting the Tuner Region ............................................... 22
Opening the MTP Source .................................................... 22
Adjusting the VHF Squelch ................................................. 23
Scanning VHF Channels ..................................................... 23
Icons .................................................................................... 23
Adjusting the Volume ............................................................... 23
Enabling and Disabling Zones ............................................ 23
Muting the Media Volume ................................................... 23
Setting the Device Name ......................................................... 23
Viewing Video...............................................................23
Configuring the Video Appearance .......................................... 23
Table of Contents
SiriusXM®..................................................................... 23
SiriusXM Equipment and Subscription Requirements ............. 23
Weather Data Broadcasts ........................................................ 23
Viewing Precipitation Information ............................................. 23
Precipitation Views .............................................................. 23
Storm Cell and Lightning Information ....................................... 24
Hurricane Information .............................................................. 24
Weather Warnings and Weather Bulletins ............................... 24
Forecast Information ................................................................ 24
Viewing Forecast Information for Another Time Period ...... 24
Viewing a Marine Forecast or an Offshore Forecast ........... 24
Weather Fronts and Pressure Centers ............................... 24
City Forecasts ..................................................................... 24
Viewing Sea Conditions ........................................................... 25
Surface Winds ..................................................................... 25
Wave Height, Wave Period, and Wave Direction ................ 25
Viewing Forecast Sea Conditions Information for Another
Time Period ......................................................................... 25
Viewing Fishing Information ..................................................... 25
Surface Pressure and Water Temperature Data ................. 25
Forecasting Fish Locations ................................................. 25
Changing the Sea Surface Temperature Color Range ....... 25
Visibility Information ................................................................. 25
Viewing Forecast Visibility Information for Another Time
Period .................................................................................. 25
Viewing Buoy Reports .............................................................. 25
Viewing Local Weather Information near a Buoy ................ 26
Creating a Waypoint on a Weather Chart ................................ 26
Weather Overlay ...................................................................... 26
Turning On the Weather Overlay on a Chart ...................... 26
Weather Overlay Settings on the Navigation Chart ............ 26
Weather Overlay Settings on the Fishing Chart .................. 26
Viewing Weather Subscription Information .............................. 26
SiriusXM Radio ........................................................................ 26
Customizing the Channel Guide ......................................... 26
Saving a SiriusXM Channel to the Presets List ................... 26
Adjusting SiriusXM Satellite Radio Volume ......................... 26
Adjusting the Distance from Shore ................................. 30
Other Vessel Settings .............................................................. 30
Viewing System Software Information ..................................... 30
Restoring the Original Chartplotter Factory Settings ............... 30
Chartplotter Data Management ................................... 30
Copying Waypoints, Routes, and Tracks to a Chartplotter ...... 30
Copying Data from a Memory Card ......................................... 30
Copying Waypoints, Routes, and Tracks to a Memory Card ... 30
Copying Waypoints, Routes, and Tracks to or from all
Chartplotters on the Network ................................................... 31
Copying Built-In Maps to a Memory Card ................................ 31
Backing Up Data to a Computer .............................................. 31
Restoring Backup Data to a Chartplotter ................................. 31
Saving System Information to a Memory Card ........................ 31
Appendix.......................................................................31
Registering Your Device .......................................................... 31
Calibrating the Touchscreen .................................................... 31
Loading the New Software on a Memory Card ........................ 31
Updating the Device Software ................................................. 31
Screenshots ............................................................................. 31
Capturing Screenshots ........................................................ 32
Copying Screenshots to a Computer .................................. 32
NMEA 0183 Information ........................................................... 32
NMEA 2000 PGN Information .................................................. 32
Index..............................................................................33
Device Configuration................................................... 26
Turning On the Chartplotter Automatically ............................... 26
System Settings ....................................................................... 26
GPS Settings ....................................................................... 26
Viewing the Event Log ........................................................ 27
Viewing System Software Information ................................ 27
My Vessel Settings .................................................................. 27
Setting the Vessel Type ...................................................... 27
Setting the Keel Offset ........................................................ 27
Calibrating a Water Speed Device ...................................... 27
Setting the Water Temperature Offset ................................ 27
Communications Settings ........................................................ 28
NMEA 2000 and NMEA 0183 ............................................. 28
NMEA 0183 .................................................................... 28
NMEA 2000 Settings ...................................................... 28
Communication with Wireless Devices .............................. 28
Setting Up the Wireless Network .................................... 28
Connecting a Wireless Device to the Chartplotter .......... 28
Changing the Wireless Channel ..................................... 28
Connecting a Bluetooth Wireless Device ....................... 28
Disconnecting a Bluetooth Wireless Device ................... 29
Setting Alarms .......................................................................... 29
Navigation Alarms ............................................................... 29
System Alarms .................................................................... 29
Setting the Fuel Alarm ......................................................... 29
Setting Weather Alarms ...................................................... 29
Units Settings ........................................................................... 29
Navigation Settings .................................................................. 29
Auto Guidance Line Configurations .................................... 29
Table of Contents
iii
Introduction
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.‍
Device Views
echoMAP 70 Series and GPSMAP 700 Series
Zooms in to a chart or view.‍
Scrolls, highlights options, and moves the cursor.‍
SELECT
Acknowledges messages and selects options.‍
BACK
Returns to the previous screen.‍
MARK
Saves the present location as a waypoint.‍
HOME
Returns to the Home screen.‍
MENU
Opens a menu of options for the page, when applicable.‍
Closes a menu, when applicable.‍
Tips and Shortcuts
• Select Home from any screen to return to the Home screen.‍
• Select Menu from any main screen to access additional
settings about that screen.‍
• Press to adjust the backlight and lock the touchscreen.‍
• Hold to turn the chartplotter on or off.‍
Downloading the Manuals
À
Á
Â
Ã
Power key
Automatic backlight sensor
Touchscreen
microSD™ memory card slots
Using the Touchscreen
• Tap the screen to select an item.‍
• Drag or swipe your finger across the screen to pan or scroll.‍
• Pinch two fingers together to zoom out.‍
• Spread two fingers apart to zoom in.‍
Locking the Touchscreen
You can lock the touchscreen to prevent inadvertent screen
touches.‍
1 Select .‍
2 Select Lock Touchscreen.‍
echoMAP 50 Series and GPSMAP 500 Series
You can get the latest owner's manual and translations of
manuals from the web.‍
1 Go to www.garmin.com/‍support.‍
2 Select Manuals.‍
3 Follow the on-screen instructions to download the manual for
your product.‍
Manual Conventions
In this manual, the term “select” is used to describe these
actions.‍
• Touching an item on the screen (for touchscreen devices
only).‍
• Using the arrow keys to highlight a menu item, and then
pressing SELECT (for hard key devices only).‍
• Pressing a key, such as SELECT or MENU.‍
When you are instructed to select multiple items in a series,
small arrows appear in the text.‍ For example, "select Menu >
Add," indicates that you need to select the Menu item or hard
key and then select the Add item.‍
The images in this manual are for reference only and may not
match your device exactly.‍
GPS Satellite Signals
When you turn on the chartplotter, the GPS receiver must
collect satellite data and establish the current location.‍ When
the chartplotter acquires satellite signals,
appears at the top
of the Home screen.‍ When the chartplotter loses satellite
signals,
disappears and a flashing question mark appears
over on the chart.‍
For more information about GPS, go to www.garmin.com
/‍aboutGPS.‍
Adjusting the Backlight
1 Select Settings > System > Display > Backlight.‍
À
Á
Â
Ã
Automatic backlight sensor
Power key
Device keys
microSD memory card slots
Device Keys
Turns on and off the device when held.‍
Introduction
TIP: Press from any screen to access the backlight
settings.‍
2 Select an option:
• Adjust the backlight level.‍
• Select Auto Backlight or Auto.‍
Adjusting the Color Mode
Adjusts the backlight and color mode when quickly pressed
and released.‍
1 Select Settings > System > Display > Color Mode.‍
Zooms out of a chart or view.‍
2 Select an option.‍
TIP: Press
from any screen to access the color settings.‍
1
Customizing the Home Screen
You can add items to and rearrange items on the Home screen.‍
1 From the Home screen, select Customize Home.‍
2 Select an option:
• To rearrange an item, select Rearrange, select the item
to move, and select the new location.‍
• To add an item to the Home screen, select Add, and
select the new item.‍
• To remove an item you have added to the Home screen,
select Remove, and select the item.‍
Fishing Chart: Provides a detailed view of the bottom contours
and depth soundings on the chart.‍ This chart removes
navigational data from the chart, provides detailed
bathymetric data, and enhances bottom contours for depth
recognition.‍ This chart is best for offshore deep-sea fishing.‍
NOTE: The offshore Fishing chart is available with premium
charts, in some areas.‍
Radar Overlay: Superimposes radar information on the
Navigation chart or the Fishing chart, when the chartplotter is
connected to a radar.‍ This feature is not available with all
models.‍
Inserting Memory Cards
Navigation Chart and Offshore Fishing Chart
You can use optional memory cards in the chartplotter.‍ Map
cards allow you to view high-resolution satellite imagery and
aerial reference photos of ports, harbors, marinas, and other
points of interest.‍ You can use blank memory cards to record
sonar data and transfer data such as waypoints, routes, and
tracks to another compatible Garmin® chartplotter or a
computer.‍
1 Open the access door À on the front of the chartplotter.‍
NOTE: The offshore Fishing chart is available with premium
charts, in some areas.‍
The Navigation and Fishing charts allow you to plan your
course, view map information, and follow a route.‍ The Fishing
chart is for offshore fishing.‍
To open the Navigation chart, select Charts > Navigation
Chart.‍
To open the Fishing chart, select Charts > Fishing Chart.‍
Zooming In and Out of the Chart
2 Insert the memory card Á with the label facing to the right.‍
3 Press the card in until it clicks.‍
4 Close the door.‍
Charts and 3D Chart Views
The charts and 3D chart views that are available depend on the
map data and accessories used.‍
You can access the charts and 3D chart views by selecting
Charts.‍
Navigation Chart: Shows navigation data available on your
pre-loaded maps and from supplemental maps, if available.‍
The data includes buoys, lights, cables, depth soundings,
marinas, and tide stations in an overhead view.‍
Perspective 3D: Provides a view from above and behind the
boat (according to your course) and provides a visual
navigation aid.‍ This view is helpful when navigating tricky
shoals, reefs, bridges, or channels, and is beneficial when
trying to identify entry and exit routes in unfamiliar harbors or
anchorages.‍
Mariner’s Eye 3D: Shows a detailed, three-dimensional view
from above and behind the boat (according to your course)
and provides a visual navigation aid.‍ This view is helpful
when navigating tricky shoals, reefs, bridges, or channels,
and when trying to identify entry and exit routes in unfamiliar
harbors or anchorages.‍
NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are
available with premium charts, in some areas.‍
Fish Eye 3D: Provides an underwater view that visually
represents the sea floor according to the chart information.‍
When a sonar transducer is connected, suspended targets
(such as fish) are indicated by red, green, and yellow
spheres.‍ Red indicates the largest targets and green
indicates the smallest.‍
2
The zoom level is indicated by the scale number at the bottom
of the chart.‍ The bar under the scale number represents that
distance on the chart.‍
• Select to zoom out.‍
• Select to zoom in.‍
Panning the Chart
You can move the chart to view an area other than your present
location.‍
1 From the chart, drag the navigation screen or use the arrow
keys.‍
2 Select Stop Panning or Back to stop panning and return the
screen to your present location.‍
Selecting an Item on the Map Using the Device Keys
1 From a chart or 3D chart view, select , , , or to move
the cursor.‍
2 Select SELECT.‍
Chart Symbols
This table contains some of the common symbols you might see
on the detailed charts.‍
Icon
Description
Buoy
Information
Marine services
Tide station
Current station
Overhead photo available
Perspective photo available
Other features common to most charts include depth contour
lines, intertidal zones, spot soundings (as depicted on the
Charts and 3D Chart Views
original paper chart), navigational aids and symbols,
obstructions, and cable areas.‍
Navigating to a Point on the Chart
CAUTION
The Auto Guidance feature is based on electronic chart
information.‍ That data does not ensure obstacle and bottom
clearance.‍ Carefully compare the course to all visual sightings,
and avoid any land, shallow water, or other obstacles that may
be in your path.‍
When using Go To, a direct course and a corrected course may
pass over land or shallow water.‍ Use visual sightings, and steer
to avoid land, shallow water, and other dangerous objects.‍
NOTE: The offshore Fishing chart is available with premium
charts, in some areas.‍
NOTE: Auto Guidance is available with premium charts, in
some areas.‍
1 From the Navigation chart or Fishing chart, select a location.‍
2 If necessary, select SELECT.‍
3 Select Navigate To.‍
4 Select an option:
• To navigate directly to the location, select Go To.‍
• To create a route to the location, including turns, select
Route To.‍
• To use Auto Guidance, select Guide To.‍
5 Review the course indicated by the magenta line.‍
NOTE: When using Auto Guidance, a gray segment within
any part of the magenta line indicates that Auto Guidance
cannot calculate part of the Auto Guidance line.‍ This is due
to the settings for minimum safe water depth and minimum
safe obstacle height.‍
6 Follow the magenta line, steering to avoid land, shallow
water, and other obstacles.‍
Viewing Location and Object Information on a Chart
You can view information about a location or an object on the
Navigation chart or the Fishing chart.‍
NOTE: The offshore Fishing chart is available with premium
charts, in some areas.‍
1 From the Navigation chart or Fishing chart, select a location
or object.‍
A list of options appears along the right side of the chart.‍ The
options that appear vary based on the location or object you
selected.‍
2 Select an option:
• To view details of objects in the vicinity of the cursor,
select Review.‍
NOTE: Review does not appear if the cursor is not near
an object.‍ If the cursor is near only one object, the name
of the object appears.‍
• To navigate to the selected location, select Navigate To.‍
• To mark a waypoint at the cursor location, select New
Waypoint.‍
• To view the distance and bearing of the object from your
current location, select Measure Distance.‍
The distance and bearing appear on the screen.‍ Select
Set Reference to measure from a location other than
your current location.‍
• To view tide, current, celestial, chart notes, or local
services information near the cursor, select Information.‍
Viewing Details about Navaids
From the Navigation chart, Fishing chart, Perspective 3D chart
view, or Mariner’s Eye 3D chart view, you can view details
Charts and 3D Chart Views
about various types of navigation aids, including beacons,
lights, and obstructions.‍
NOTE: The offshore Fishing chart is available with premium
charts, in some areas.‍
NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are
available with premium charts, in some areas.‍
1 From a chart or 3D chart view, select a navaid.‍
2 If necessary, select Review.‍
3 Select the name of the navaid.‍
Selecting a Map
If your product has both BlueChart® g2 and LakeVü™ HD builtin maps, you can select which map to use.‍ Not all models have
both types of built-in maps.‍
1 From the Navigation chart, select Menu > Built-in Map.‍
2 Select an option:
• When you are on an inland lake, select LakeVü™ HD.‍
• When you are offshore, select BlueChart® g2.‍
Premium Charts
CAUTION
The Auto Guidance feature is based on electronic chart
information.‍ That data does not ensure obstacle and bottom
clearance.‍ Carefully compare the course to all visual sightings,
and avoid any land, shallow water, or other obstacles that may
be in your path.‍
NOTE: Not all models support all charts.‍
Optional premium charts, such as BlueChart g2 Vision®, allow
you to get the most out of your chartplotter.‍ In addition to
detailed marine charting, premium charts may contain these
features, which are available in some areas.‍
Mariner’s Eye 3D: Provides a view from above and behind the
boat for a three-dimensional navigation aid.‍
Fish Eye 3D: Provides an underwater, three-dimensional view
that visually represents the sea floor according to the
information on the chart.‍
Fishing Charts: Shows the chart with enhanced bottom
contours and without navigational data.‍ This chart works well
for offshore deep-sea fishing.‍
High Resolution Satellite Imagery: Provides high-resolution
satellite images for a realistic view of the land and water on
the Navigation chart (Showing Satellite Imagery on the
Navigation Chart).‍
Aerial Photos: Shows marinas and other navigationally
significant aerial photos to help you visualize your
surroundings (Viewing Aerial Photos of Landmarks).‍
Detailed Roads and POI data: Shows detailed road and point
of interest (POI) data, which includes highly detailed coastal
roads and POIs such as restaurants, lodging, and local
attractions.‍
Auto Guidance: Uses specified safe depth, safe height, and
chart data to determine the best course to your destination.‍
Auto Guidance is available when you navigate to a
destination using Guide To.‍
Viewing Tide Station Information
on the chart indicates a tide station.‍ You can view a detailed
graph for a tide station to help predict the tide level at different
times or on different days.‍
NOTE: This feature is available with premium charts, in some
areas.‍
1 From the Navigation chart or Fishing chart, select a tide
station.‍
Tide direction and tide level information appear near .‍
3
2 Select an option to view additional station information:
• Select the station name.‍
• If more than one item is in the vicinity, select Review, and
select the station name.‍
Animated Tide and Current Indicators
NOTE: This feature is available with premium charts, in some
areas.‍
You can view indicators for animated tide station and current
direction on the Navigation chart or the Fishing chart.‍ You must
also enable animated icons in the chart settings (Showing and
Configuring Tides and Currents).‍
An indicator for a tide station appears on the chart as a vertical
bar graph with an arrow.‍ A red arrow pointing downward
indicates a falling tide, and a blue arrow pointing upward
indicates a rising tide.‍ When you move the cursor over the tide
station indicator, the height of the tide at the station appears
above the station indicator.‍
Current direction indicators appear as arrows on the chart.‍ The
direction of each arrow indicates the direction of the current at a
specific location on the chart.‍ The color of the current arrow
indicates the range of speed for the current at that location.‍
When you move the cursor over the current direction indicator,
the specific current speed at the location appears above the
direction indicator.‍
Color
Current Speed Range
Yellow
0 to 1 knot
Orange
1 to 2 knots
Red
2 or more knots
Showing and Configuring Tides and Currents
NOTE: This feature is available with premium charts, in some
areas.‍
You can show static or animated tide and current station
indicators on the Navigation chart or Fishing chart.‍
1 From the Navigation or Fishing chart, select Menu > Chart
Setup > Tides & Currents.‍
2 Select an option:
• To show current station indicators and tide station
indicators on the chart, select On.‍
• To show animated tide station indicators and animated
current direction indicators on the chart, select Animated.‍
Showing Satellite Imagery on the Navigation Chart
NOTE: This feature is available with premium charts, in some
areas.‍
You can overlay high-resolution satellite images on the land or
on both land and sea portions of the Navigation chart.‍
NOTE: When enabled, high-resolution satellite images are
present only at lower zoom levels.‍ If you cannot see highresolution images in your optional chart region, you can select
to zoom in.‍ You also can set the detail level higher by
changing the map zoom detail.‍
1 From the Navigation chart, select Menu > Chart Setup >
Satellite Photos.‍
2 Select an option:
• Select Land Only to show standard chart information on
the water, with photos overlaying the land.‍
• Select Photo Map Blend to show photos on both the
water and the land at a specified opacity.‍ Use the slider
bar to adjust the photo opacity.‍ The higher you set the
percentage, the more the satellite photos cover both land
and water.‍
Viewing Aerial Photos of Landmarks
Before you can view aerial photos on the Navigation chart, you
must turn on the Photo setting in the chart setup.‍
4
NOTE: This feature is available with premium charts, in some
areas.‍
You can use aerial photographs of landmarks, marinas, and
harbors to help orient yourself to your surroundings or to
acquaint yourself with a marina or a harbor prior to arrival.‍
1 From the Navigation chart, select a camera icon:
• To view an overhead photo, select
.‍
• To view a perspective photo, select
.‍ The photo was
taken from the location of the camera, pointed in the
direction of the cone.‍
2 Select Review > Aerial Photo.‍
Automatic Identification System
The Automatic Identification System (AIS) enables you to
identify and track other vessels, and alerts you to area traffic.‍
When connected to an external AIS device, the chartplotter can
show some AIS information about other vessels that are within
range, that are equipped with a transponder, and that are
actively transmitting AIS information.‍ The information reported
for each vessel includes the Maritime Mobile Service Identity
(MMSI), location, GPS speed, GPS heading, time that has
elapsed since the last position of the vessel was reported,
nearest approach, and time to the nearest approach.‍
AIS Targeting Symbols
Symbol Description
AIS vessel.‍ The vessel is reporting AIS information.‍ The
direction in which the triangle is pointing indicates the
direction in which the AIS vessel is moving.‍
Target is selected.‍
Target is activated.‍ The target appears larger on the chart.‍ A
green line attached to the target indicates the heading of the
target.‍ The MMSI, speed, and direction of the vessel appear
beneath the target, if the details setting has been set to
Show.‍ If the AIS transmission from the vessel is lost, a
message banner appears.‍
Target is lost.‍ A green X indicates that the AIS transmission
from the vessel is lost, and the chartplotter displays a
message banner asking whether the vessel should continue
to be tracked.‍ If you discontinue vessel tracking, the lost
target symbol disappears from the chart or the 3D chart view.‍
Dangerous target in range.‍ The target flashes while an alarm
sounds and a message banner appears.‍ After the alarm has
been acknowledged, a solid red triangle with a red line
attached to it indicates the location and the heading of the
target.‍ If the safe-zone collision alarm has been set to Off, the
target flashes, but the audible alarm does not sound and the
alarm banner does not appear.‍ If the AIS transmission from
the vessel is lost, a message banner appears.‍
Dangerous target is lost.‍ A red X indicates that the AIS
transmission from the vessel is lost, and the chartplotter
displays a message banner asking whether the vessel should
continue to be tracked.‍ If you discontinue vessel tracking, the
lost dangerous target symbol disappears from the chart or the
3D chart view.‍
The location of this symbol indicates the closest point of
approach to a dangerous target, and the numbers near the
symbol indicate the time to the closest point of approach to
that target.‍
Heading and Projected Course of Activated AIS
Targets
When heading and course over ground information are provided
by an activated AIS target, the heading of the target appears on
a chart as a solid line attached to the AIS target symbol.‍ A
heading line does not appear on a 3D chart view.‍
The projected course of an activated AIS target appears as a
dashed line on a chart or a 3D chart view.‍ The length of the
projected course line is based on the value of the projected
heading setting.‍ If an activated AIS target is not transmitting
Charts and 3D Chart Views
speed information, or if the vessel is not moving, a projected
course line does not appear.‍ Changes in the speed, course over
ground, or rate of turn information transmitted by the vessel can
impact the calculation of the projected course line.‍
When course over ground, heading, and rate of turn information
are provided by an activated AIS target, the projected course of
the target is calculated based on the course over ground and
the rate of turn information.‍ The direction in which the target is
turning, which is also based on the rate of turn information, is
indicated by the direction of the barb at the end of the heading
line.‍ The length of the barb does not change.‍
When course over ground and heading information are provided
by an activated AIS target, but rate of turn information is not
provided, the projected course of the target is calculated based
on the course over ground information.‍
Showing AIS Vessels on a Chart or 3D Chart View
Before you can use AIS, you must connect the chartplotter to an
external AIS device and receive active transponder signals from
other vessels.‍
You can configure how other vessels appear on a chart or on a
3D chart view.‍ The display range configured for one chart or
one 3D chart view are applied only to that chart or to that 3D
chart view.‍ The details, projected heading, and trails settings
configured for one chart or one 3D chart view are applied to all
charts and to all 3D chart views.‍
1 From a chart or 3D chart view, select Menu > Other Vessels
> Display Setup.‍
2 Select an option:
• To indicate the distance from your location in which AIS
vessels appear, select Display Range, and select a
distance.‍
• To show details about AIS-activated vessels, select
Details > Show.‍
• To set the projected heading time for AIS-activated
vessels, select Proj.‍ Heading, and enter the time.‍
• To show the tracks of AIS vessels, select Trails, and
select the length of the track that appears using a trail.‍
Activating a Target for an AIS Vessel
1 From a chart or a 3D chart view, select an AIS vessel.‍
2 Select AIS Vessel > Activate Target.‍
Viewing Information about a Targeted AIS Vessel
You can view the AIS signal status, MMSI, GPS speed, GPS
heading, and other information that is reported about a targeted
AIS vessel.‍
1 From a chart or a 3D chart view, select an AIS vessel.‍
2 Select AIS Vessel.‍
Deactivating a Target for an AIS Vessel
1 From a chart or a 3D chart view, select an AIS vessel.‍
2 Select AIS Vessel > Deactivate Target.‍
Viewing a List of AIS Threats
From a chart or 3D chart view, select Menu > Other Vessels
> AIS List.‍
Setting the Safe-Zone Collision Alarm
Before you can set a safe-zone collision alarm, you must have a
compatible chartplotter connected to an AIS device.‍
The safe-zone collision alarm is used only with AIS.‍ The safe
zone is used for collision avoidance, and can be customized.‍
1 Select Settings > Alarms > AIS > AIS Alarm > On.‍
Charts and 3D Chart Views
2
3
4
5
A message banner appears and an alarm sounds when an
AIS-activated vessel enters the safe-zone area around your
boat.‍ The object is also labeled as dangerous on the screen.‍
When the alarm is off, the message banner and audible
alarm are disabled, but the object is still labeled as
dangerous on the screen.‍
Select Range.‍
Select a distance for the safe-zone radius around your
vessel.‍
Select Time To.‍
Select a time at which the alarm will sound if a target is
determined to intersect the safe zone.‍
For example, to be notified of a pending intersection 10
minutes before it will likely occur, set Time To to 10, and the
alarm will sound 10 minutes before the vessel intersects the
safe zone.‍
AIS Distress Signals
Self-contained AIS distress signal devices transmit emergency
position reports when activated.‍ The chartplotter can receive
signals from Search and Rescue Transmitters (SART),
Emergency Position Indicating Radio Beacons (EPIRB), and
other man overboard signals.‍ Distress signal transmissions are
different than standard AIS transmissions, so they appear
differently on the chartplotter.‍ Instead of tracking a distress
signal transmission for collision avoidance, you track a distress
signal transmission to locate and assist a vessel or person.‍
Navigating to a Distress Signal Transmission
When you receive a distress signal transmission, a distress
signal alarm appears.‍
Select Review > Go To to begin navigation to the
transmission.‍
AIS Distress Signal Device Targeting Symbols
Symbol Description
AIS distress signal device transmission.‍ Select to see more
information about the transmission and begin navigation.‍
Transmission lost.‍
Transmission test.‍ Appears when a vessel initiates a test of
their distress signal device, and does not represent a true
emergency.‍
Transmission test lost.‍
Enabling AIS Transmission Test Alerts
To avoid a large number of test alerts and symbols in crowded
areas such as marinas, you can select to receive or ignore AIS
test messages.‍ To test an AIS emergency device, you must
enable the chartplotter to receive test alerts.‍
1 Select Settings > Alarms > AIS.‍
2 Select an option:
• To receive or ignore Emergency Position Indicating Radio
Beacon (EPRIB) test signals, select AIS-EPIRB Test.‍
• To receive or ignore Man Overboard (MOB) test signals,
select AIS-MOB Test.‍
• To receive or ignore Search and Rescue Transponder
(SART) test signals, select AIS-SART Test.‍
Turning Off AIS Reception
AIS signal reception is turned on by default.‍
Select Settings > Other Vessels > AIS > Off.‍
All AIS functionality on all charts and 3D chart views is
disabled.‍ This includes AIS vessel targeting and tracking,
collision alarms that result from AIS vessel targeting and
tracking, and the display of information about AIS vessels.‍
5
Chart and 3D Chart View Settings
NOTE: Not all settings apply to all charts and 3D chart views.‍
Some options require premium maps or connected accessories,
such as radar.‍
These settings apply to the charts and 3D chart views, except
the radar overlay and Fish Eye 3D (Fish Eye 3D Settings).‍
From a chart or a 3D chart view, select Menu.‍
Waypoints & Tracks: See Waypoints and Tracks Settings on
the Charts and Chart Views.‍
Other Vessels: See Other Vessels Settings on the Charts and
Chart Views.‍
Surface Radar: Shows surface radar details on the Perspective
3D or Mariner's Eye 3D chart views.‍
Weather Radar: Shows weather radar imaging on the
Perspective 3D or Mariner's Eye 3D chart views.‍
Navaids: Shows navigational aids on the Fishing chart.‍
Laylines: Adjusts the laylines, when in sailing mode (Laylines
Settings).‍
Chart Setup: See Navigation and Fishing Chart Setup.‍
Overlay Numbers: See Overlay Numbers Settings.‍ This might
appear in the Chart Setup menu.‍
Chart Appearance: See Chart Appearance Settings.‍ This might
appear in the Chart Setup menu.‍
Navigation and Fishing Chart Setup
NOTE: Not all settings apply to all charts and 3D chart views.‍
Some settings require external accessories or applicable
premium charts.‍
From the Navigation chart or Fishing chart, select Menu >
Chart Setup.‍
Satellite Photos: Shows camera icons in some areas when
using some premium charts.‍ This enables you to view aerial
photos of landmarks (Viewing Aerial Photos of Landmarks).‍
Tides & Currents: Shows current station indicators and tide
station indicators on the chart (Showing and Configuring
Tides and Currents).‍
Roses: Shows a compass rose around your boat, indicating
compass direction oriented to the heading of the boat.‍ A true
wind direction or apparent wind direction indicator appears if
the chartplotter is connected to a compatible marine wind
sensor.‍ When in sailing mode, true and apparent wind are
shown on the wind rose.‍
Weather: Sets which weather items are shown on the chart,
when the chartplotter is connected to a compatible weather
receiver with an active subscription.‍
Lake Level: Allows you to enter the present level of the lake.‍
Overlay Numbers: See Overlay Numbers Settings.‍
Chart Appearance: See Chart Appearance Settings.‍
Waypoints and Tracks Settings on the Charts and
Chart Views
From a chart or a 3D chart view, select Menu > Waypoints &
Tracks.‍
Tracks: Shows tracks on the chart or 3D chart view.‍
Waypoints: Shows the Waypoints list (Viewing a List of all
Waypoints).‍
New Wpt: Creates a new waypoint.‍
Waypoint Display: Sets how to display waypoints on the chart
or 3D chart view.‍
Active Tracks: Shows the active track options menu.‍
Saved Tracks: Shows the list of saved tracks (Viewing a List of
Saved Tracks).‍
6
Tracks Display: Sets which tracks to display on the chart or 3D
chart view based on track color.‍
Laylines Settings
When in sailing mode (Setting the Vessel Type), you can
display laylines on the navigation chart.‍ Laylines can be
especially helpful when racing.‍
From the navigation chart, select Menu.‍
Display: Adjusts how the laylines and vessel are shown on the
chart, and adjusts the length of the laylines.‍
Sailing Angle: Allows you to select how the device calculates
laylines.‍ The Actual setting calculates the laylines by using
the measured wind angle from the wind sensor.‍ The Manual
setting calculates the laylines by using manually entered
windward and leeward angles.‍
Tide Correction: Corrects the laylines based on the tide.‍
Overlay Numbers Settings
From a chart, 3D chart view, the Radar screen, or a
Combinations screen, select Menu > Overlay Numbers.‍
Edit Layout: Sets the layout of the data overlay, or data fields.‍
You can select the data to be shown within each data field.‍
Navigation Inset: Shows the navigation inset when the vessel
is navigating to a destination.‍
Navigation Inset Setup: Allows you to configure the navigation
inset to show Route Leg Details, and to control when the
inset appears before a turn or destination.‍
Compass Tape: Shows the compass tape data bar when the
vessel is navigating to a destination.‍
Editing the Data Fields
You can change the data shown in the overlay numbers
displayed on the charts and other screens.‍
1 From a screen that supports overlay numbers, select Menu.‍
2 If necessary, select Chart Setup.‍
3 Select Overlay Numbers > Edit Layout.‍
4 Select a layout.‍
5 Select a data field.‍
6 Select the type of data shown in the field.‍
Available data options vary based on the chartplotter and
network configuration.‍
Showing a Navigation Inset
You can control whether a navigation inset appears on some
chart views.‍ The navigation inset is shown only when the boat is
navigating to a destination.‍
1 From a chart or 3D chart view, select Menu.‍
2 If necessary, select Chart Setup.‍
3 Select Overlay Numbers > Navigation Inset > Auto.‍
4 Select Navigation Inset Setup.‍
5 Complete an action:
• To show waypoint velocity made good (VMG) when
navigating a route with more than one leg, select Route
Leg Details > On.‍
• To show next-turn data based on distance, select Next
Turn > Distance.‍
• To show next-turn data based on time, select Next Turn >
Time.‍
• To indicate how the destination data appears, select
Destination, and select an option.‍
Chart Appearance Settings
You can adjust the appearance of the different chart views.‍
Each setting is specific for the type of chart view that you are in.‍
Charts and 3D Chart Views
NOTE: Not all settings apply to all charts and 3D chart views
and chartplotter models.‍ Some options require premium maps
or connected accessories, such as radar.‍
From a chart or 3D chart view, select Menu > Chart Setup >
Chart Appearance.‍
Orientation: Sets the perspective of the map.‍
Detail: Adjusts the amount of detail shown on the map, at
different zoom levels.‍
Heading Line: Shows and adjusts the heading line, which is a
line drawn on the map from the bow of the boat in the
direction of travel, and sets the data source for the heading
line.‍
World Map: Uses either a basic world map or a shaded relief
map on the chart.‍ These differences are visible only when
zoomed out too far to see the detailed charts.‍
Spot Depths: Turns on spot soundings and sets a dangerous
depth.‍ Spot depths that are equal to or more shallow than
the dangerous depth are indicated by red text.‍
Safety Shading: Sets the shades from the shoreline to the
specified depth.‍
Depth Range Shading: Specifies an upper and lower depth to
shade between.‍
Symbols: Shows and configures the appearance of various
symbols on the chart, such as the vessel icon, navaid
symbols, land POIs, and light sectors.‍
Style: Sets how the chart appears over 3D terrain.‍
Hazard Colors: Shows shallow water and land with a color
scale.‍ Blue indicates deep water, yellow is shallow water,
and red is very shallow water.‍
Safe Depth: Sets the appearance of a safe depth for Mariner’s
Eye 3D.‍
NOTE: This setting affects only the appearance of hazard
colors in Mariner’s Eye 3D.‍ It does not affect the safe water
depth Auto Guidance setting or the sonar shallow water
alarm setting.‍
Range Rings: Shows and configures the appearance of range
rings, which help you to visualize distances in some chart
views.‍
Lane Width: Specifies the width of the navigation lane, which is
the magenta line in some chart views that indicates the
course to your destination.‍
Setting the Heading and Course Over Ground Lines
You can show the heading line and the course over ground
(COG) line on the chart.‍
COG is your direction of movement.‍ Heading is the direction the
bow of the boat is pointed, when a heading sensor is
connected.‍
1 From a chart view, select Menu > Chart Setup > Chart
Appearance > Heading Line.‍
2 If necessary, select Source, and select an option:
• To automatically use the source available, select Auto.‍
• To use the GPS antenna heading for COG, select GPS
Heading (COG).‍
• To use data from a connected heading sensor, select
Heading.‍
• To use data from both a connected heading sensor and
the GPS antenna, select COG and Heading.‍
This displays both the heading line and the COG line on
the chart.‍
3 Select Display, and select an option:
• Select Distance > Distance, and enter the length of the
line shown on the chart.‍
Navigation with a Chartplotter
• Select Time > Time, and enter the time used to calculate
the distance your boat will travel in the specified time at
your present speed,
Other Vessels Settings on the Charts and Chart
Views
NOTE: These options require connected accessories, such as
an AIS receiver or VHF radio.‍
From a chart or 3D chart view, select Menu > Other Vessels.‍
AIS List: Shows the AIS list (Viewing a List of AIS Threats).‍
DSC List: Shows the DSC list (DSC List).‍
Display Setup: See AIS Display Settings.‍
DSC Trails: Shows the tracks of DSC vessels, and selects the
length of the track that appears using a trail.‍
AIS Alarm: Sets the safe-zone collision alarm (Setting the SafeZone Collision Alarm).‍
AIS Display Settings
NOTE: AIS requires the use of an external AIS device and
active transponder signals from other vessels.‍
From a chart or 3D chart view, select Menu > Other Vessels >
Display Setup.‍
AIS Display Range: Indicates the distance from your location
within which AIS vessels appear.‍
Details: Shows details about AIS-activated vessels.‍
Proj.‍ Heading: Sets the projected heading time for AISactivated vessels.‍
Trails: Shows the tracks of AIS vessels, and select the length of
the track that appears using a trail.‍
Fish Eye 3D Settings
NOTE: This feature is available with premium charts, in some
areas.‍
From the Fish Eye 3D chart view, select Menu.‍
View: Sets the perspective of the 3D chart view.‍
Tracks: Shows tracks.‍
Sonar Cone: Shows a cone that indicates the area covered by
the transducer.‍
Fish Symbols: Shows suspended targets.‍
Navigation with a Chartplotter
CAUTION
If your vessel has an autopilot system, a dedicated autopilot
control display must be installed at each steering helm in order
to disable the autopilot system.‍
The Auto Guidance feature is based on electronic chart
information.‍ That data does not ensure obstacle and bottom
clearance.‍ Carefully compare the course to all visual sightings,
and avoid any land, shallow water, or other obstacles that may
be in your path.‍
NOTE: Auto Guidance is available with premium charts, in
some areas.‍
NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are
available with premium charts, in some areas.‍
NOTE: The offshore Fishing chart is available with premium
charts, in some areas.‍
To navigate, you must choose a destination, set a course or
create a route, and follow the course or route.‍ You can follow
the course or the route on the Navigation chart, Fishing chart,
Perspective 3D chart view, or Mariner’s Eye 3D chart view.‍
7
Basic Navigation Questions
Question
Answer
How do I make the chartplotter Navigate using Go To.‍ See Setting
point me in the direction in
and Following a Direct Course Using
which I want to go (bearing)? Go To.‍
How do I make the device
guide me along a straight line
(minimizing cross track) to a
location using the shortest
distance from the present
location?
Build a single-leg route and navigate it
using Route To.‍ See Creating and
Navigating a Route From Your
Present Location.‍
How do I make the device
guide me to a location while
avoiding charted obstacles?
Build a multi-leg route and navigate it
using Route To.‍ See Creating and
Navigating a Route From Your
Present Location.‍
How do I make the device
steer my automatic pilot?
Navigate using Route To.‍ See Creating and Navigating a Route From
Your Present Location.‍
Can the device create a path
for me?
If you have premium maps that
support Auto Guidance and are in an
area covered by Auto Guidance,
navigate using Auto Guidance.‍ See Setting and Following a Course Using
Auto Guidance.‍
How do I change the Auto
Guidance settings for my
boat?
See Auto Guidance Line
Configurations.‍
Destinations
3 If necessary, select the marine service category.‍
The chartplotter shows a list of the nearest locations and the
distance and bearing to each.‍
Select a destination.‍
4
You can select or to view additional information or to
show the location on a chart.‍
Courses
CAUTION
The Auto Guidance feature is based on electronic chart
information.‍ That data does not ensure obstacle and bottom
clearance.‍ Carefully compare the course to all visual sightings,
and avoid any land, shallow water, or other obstacles that may
be in your path.‍
When using Go To, a direct course and a corrected course may
pass over land or shallow water.‍ Use visual sightings, and steer
to avoid land, shallow water, and other dangerous objects.‍
NOTE: Auto Guidance is available with premium charts, in
some areas.‍
You can set and follow a course to a destination using one of
three methods: Go To, Route To, or Guide To.‍
Go To: Takes you directly to the destination.‍
Route To: Creates a route from your location to a destination,
allowing you to add turns along the way.‍
Guide To: Create a path to a destination using Auto Guidance.‍
You can select destinations using various charts and 3D chart
views or using the lists.‍
Setting and Following a Direct Course Using Go To
Searching for a Destination by Name
CAUTION
When using Go To, a direct course and a corrected course may
pass over land or shallow water.‍ Use visual sightings, and steer
to avoid land, shallow water, and other dangerous objects.‍
You can search for saved waypoints, saved routes, saved
tracks, and marine services destinations by name.‍
1 Select Nav Info > Search by Name.‍
2 Enter at least a portion of the name of your destination.‍
3 If necessary, select Done.‍
The 50 nearest destinations that contain your search criteria
appear.‍
4 Select the destination.‍
Selecting a Destination Using the Navigation Chart
From the Navigation chart, select a destination.‍
Searching for a Destination Using Nav Info
1 Select Nav Info.‍
2 Select an option:
• To view a list of preloaded locations and previously
marked locations, select Waypoints.‍
• To view a list of previously saved routes, select Routes.‍
• To view a list of recorded tracks, select Tracks.‍
• To view a list of slips, moorings, and other offshore points
of interest, select Offshore Services.‍
• To view a list of marinas and other inland points of
interest, select Inland Services.‍
• To search for a destination by name, select Search by
Name.‍
Select a destination.‍
3
Searching for a Marine Services Destination
NOTE: This feature is available with premium charts, in some
areas.‍
The chartplotter contains information for thousands of
destinations offering marine services.‍
1 Select Nav Info.‍
2 Select Offshore Services or Inland Services.‍
8
You can set and follow a direct course from your current
location to a selected destination.‍
1 Select a destination (Destinations).‍
2 Select Navigate To > Go To.‍
A magenta line appears.‍ In the center of the magenta line is
a thinner purple line that represents the corrected course
from your current location to the destination.‍ The corrected
course is dynamic, and it moves with your boat when you are
off course.‍
3 Follow the magenta line, steering to avoid land, shallow
water, and other obstacles.‍
4 If you are off course, follow the purple line (corrected course)
to go to your destination, or steer back to the magenta line
(direct course).‍
Setting and Following a Course Using Auto Guidance
CAUTION
The Auto Guidance feature is based on electronic chart
information.‍ That data does not ensure obstacle and bottom
clearance.‍ Carefully compare the course to all visual sightings,
and avoid any land, shallow water, or other obstacles that may
be in your path.‍
NOTE: Auto Guidance is available with premium charts, in
some areas.‍
1 Select a destination (Destinations).‍
2 Select Navigate To > Guide To.‍
3 Review the course indicated by the magenta Auto Guidance
line.‍
4 Follow the magenta line, steering to avoid land, shallow
water, and other obstacles.‍
Navigation with a Chartplotter
NOTE: When using Auto Guidance, a gray segment within
any part of the magenta line indicates that Auto Guidance
cannot calculate part of the Auto Guidance line.‍ This is due
to the settings for minimum safe water depth and minimum
safe obstacle height.‍
Autopilot Navigation
When you start navigation (Go To, Route To, or Guide To), if
you are connected through a NMEA 2000® network to a
compatible Garmin autopilot, you are prompted to engage the
autopilot.‍
Stopping Navigation
From the Navigation chart or Fishing chart, select Menu >
Stop Navigation.‍
Waypoints
Waypoints are locations you record and store in the device.‍
Marking Your Present Location as a Waypoint
From any screen, select Mark.‍
Creating a Waypoint at a Different Location
1 Select Nav Info > Waypoints > New Waypoint.‍
2 Select an option:
• To create the waypoint by entering position coordinates,
select Enter Coordinates, and enter the coordinates.‍
• To create the waypoint using a chart, select Use Chart,
select the location, and select Move Waypoint.‍
Marking and Starting Navigation to an MOB Location
When you mark a waypoint, you can designate it as a man
overboard (MOB) location.‍
Select an option:
• From any screen, select Mark > Man Overboard.‍
• From the Home screen, select Man Overboard > Yes.‍
An international MOB symbol marks the active MOB point and
the chartplotter sets a direct course back to the marked location.‍
Viewing a List of all Waypoints
Select Nav Info > Waypoints.‍
Editing a Saved Waypoint
1 Select Nav Info > Waypoints.‍
2 Select a waypoint.‍
3 Select Edit Waypoint.‍
4 Select an option:
•
•
•
•
•
•
To add a name, select Name, and enter a name.‍
To change the symbol, select Symbol.‍
To change the depth, select Depth.‍
To change the water temperature, select Water Temp.‍.‍
To change the comment, select Comment.‍
To move the position of the waypoint, select Move.‍
Moving a Saved Waypoint
1 Select Nav Info > Waypoints.‍
2 Select a waypoint.‍
3 Select Edit Waypoint > Move.‍
4 Indicate a new location for the waypoint:
• To move the waypoint while using the chart, select Use
Chart, select a new location on the chart, and select
Move Waypoint.‍
• To move the waypoint using coordinates, select Enter
Coordinates, and enter the new coordinates.‍
Navigation with a Chartplotter
Browsing for and Navigating to a Saved Waypoint
CAUTION
The Auto Guidance feature is based on electronic chart
information.‍ That data does not ensure obstacle and bottom
clearance.‍ Carefully compare the course to all visual sightings,
and avoid any land, shallow water, or other obstacles that may
be in your path.‍
When using Go To, a direct course and a corrected course may
pass over land or shallow water.‍ Use visual sightings, and steer
to avoid land, shallow water, and other dangerous objects.‍
NOTE: Auto Guidance is available with premium charts, in
some areas.‍
Before you can navigate to a waypoint, you must create a
waypoint.‍
1 Select Nav Info > Waypoints.‍
2 Select a waypoint.‍
3 Select Navigate To.‍
4 Select an option:
• To navigate directly to the location, select Go To.‍
• To create a route to the location, including turns, select
Route To.‍
• To use Auto Guidance, select Guide To.‍
5 Review the course indicated by the magenta line.‍
NOTE: When using Auto Guidance, a gray segment within
any part of the magenta line indicates that Auto Guidance
cannot calculate part of the Auto Guidance line.‍ This is due
to the settings for minimum safe water depth and minimum
safe obstacle height.‍
6 Follow the magenta line, steering to avoid land, shallow
water, and other obstacles.‍
Deleting a Waypoint or an MOB
1 Select Nav Info > Waypoints.‍
2 Select a waypoint or an MOB.‍
3 Select Delete.‍
Deleting All Waypoints
Select Nav Info > Manage Data > Clear User Data >
Waypoints > All.‍
Routes
Creating and Navigating a Route From Your Present
Location
You can create and immediately navigate a route on the
Navigation chart or the Fishing chart.‍ This procedure does not
save the route or the waypoint data.‍
NOTE: The offshore Fishing chart is available with premium
charts, in some areas.‍
1 From the Navigation chart or Fishing chart, select a
destination.‍
2 Select Navigate To > Route To.‍
3 Select the location of the last turn before the destination.‍
4 Select Add Turn.‍
5 If necessary, repeat step 3 and 4 to add additional turns,
working backward from the destination to the present
location of your vessel.‍
The last turn you add should be the first turn you make,
starting from your present location.‍ It should be the turn
closest to your vessel.‍
6 If necessary, select Menu.‍
7 Select Navigate Route.‍
8 Review the course indicated by the magenta line.‍
9
9 Follow the magenta line, steering to avoid land, shallow
4 Select Offset to navigate parallel to the route, offset from it
Creating and Saving a Route
5 Indicate how to navigate the route:
water, and other obstacles.‍
This procedure saves the route and all the waypoints in it.‍ The
starting point can be your present location or another location.‍
1 Select Nav Info > Routes > New Route > Use Chart.‍
2 Select the starting location of the route.‍
3 Select Add Turn.‍
4 Select the location of the next turn on the chart.‍
5 Select Add Turn.‍
The chartplotter marks the location of the turn with a
waypoint.‍
6 If necessary, repeat steps 4 and 5 to add more turns.‍
7 Select the final destination.‍
by a specific distance.‍
6
Viewing a List of Routes
Select Nav Info > Routes.‍
Editing a Saved Route
You can change the name of a route or change the turns the
route contains.‍
1 Select Nav Info > Routes.‍
2 Select a route.‍
3 Select Edit Route.‍
4 Select an option:
• To change the name, select Name, and enter the name.‍
• To select a waypoint from the turn list, select Edit Turns
> Use Turn List, and select a waypoint from the list.‍
• To select a turn using the chart, select Edit Turns > Use
Chart, and select a location on the chart.‍
Browsing for and Navigating a Saved Route
Before you can browse a list of routes and navigate to one of
them, you must create and save at least one route.‍
1 Select Nav Info > Routes.‍
2 Select a route.‍
3 Select Navigate To.‍
4 Select an option:
• To navigate the route from the starting point used when
the route was created, select Forward.‍
• To navigate the route from the destination point used
when the route was created, select Backward.‍
A magenta line appears.‍ In the center of the magenta line is
a thinner purple line that represents the corrected course
from your present location to the destination.‍ The corrected
course is dynamic, and it moves with your boat when you are
off course.‍
5 Review the course indicated by the magenta line.‍
6 Follow the magenta line along each leg in the route, steering
to avoid land, shallow water, and other obstacles.‍
7 If you are off course, follow the purple line (corrected course)
to go to your destination, or steer back to the magenta line
(direct course).‍
Browsing for and Navigating Parallel to a Saved
Route
Before you can browse a list of routes and navigate to one of
them, you must create and save at least one route.‍
1 Select Nav Info > Routes.‍
2 Select a route.‍
3 Select Navigate To.‍
10
7
8
9
• To navigate the route from the starting point used when
the route was created, to the left of the original route,
select Forward – Port.‍
• To navigate the route from the starting point used when
the route was created, to the right of the original route,
select Forward – Starboard.‍
• To navigate the route from the destination point used
when the route was created, to the left of the original
route, select Backward – Port.‍
• To navigate the route from the destination point used
when the route was created, to the right of the original
route, select Backward – Starboard.‍
If necessary, select Done.‍
A magenta line appears.‍ In the center of the magenta line is
a thinner purple line that represents the corrected course
from your present location to the destination.‍ The corrected
course is dynamic, and it moves with your boat when you are
off course.‍
Review the course indicated by the magenta line.‍
Follow the magenta line along each leg in the route, steering
to avoid land, shallow water, and other obstacles.‍
If you are off course, follow the purple line (corrected course)
to go to your destination, or steer back to the magenta line
(direct course).‍
Deleting a Saved Route
1 Select Nav Info > Routes.‍
2 Select a route.‍
3 Select Delete.‍
Deleting All Saved Routes
Select Nav Info > Manage Data > Clear User Data >
Routes.‍
Tracks
A track is a recording of the path of your boat.‍ The track
currently being recorded is called the active track, and it can be
saved.‍ You can show tracks in each chart or 3D chart view.‍
Showing Tracks
From a chart or a 3D chart view, select Menu > Waypoints
& Tracks > Tracks > On.‍
A trailing line on the chart indicates your track.‍
Setting the Color of the Active Track
1 Select Nav Info > Tracks > Active Track Options > Track
Color.‍
2 Select a track color.‍
Saving the Active Track
The track currently being recorded is called the active track.‍
1 Select Nav Info > Tracks > Save Active Track.‍
2 Select an option:
• Select the time the active track began.‍
• Select Entire Log.‍
3 Select Save.‍
Viewing a List of Saved Tracks
Select Nav Info > Tracks > Saved Tracks.‍
Editing a Saved Track
1 Select Nav Info > Tracks > Saved Tracks.‍
2 Select a track.‍
Navigation with a Chartplotter
3 Select Edit Track.‍
4 Select an option:
2 Select an option:
• To record the track based on a distance between points,
select Distance > Change, and enter the distance.‍
• To record the track based on a time interval, select Time
> Change, and enter the time interval.‍
• To record the track plot based on a variance from your
course, select Resolution > Change, and enter the
maximum error allowed from the true course before
recording a track point.‍
• Select Name, and enter the new name.‍
• Select Track Color, and select a color.‍
Saving a Track as a Route
1 Select Nav Info > Tracks > Saved Tracks.‍
2 Select a track.‍
3 Select Edit Track > Save Route.‍
Browsing for and Navigating a Recorded Track
Before you can browse a list of tracks and navigate to them, you
must record and save at least one track (Tracks).‍
1 Select Nav Info > Tracks > Saved Tracks.‍
2 Select a track.‍
3 Select Follow Track.‍
4 Select an option:
• To navigate the track from the starting point used when
the track was created, select Forward.‍
• To navigate the track from the destination point used
when the track was created, select Backward.‍
5 Review the course indicated by the colored line.‍
6 Follow the line along each leg in the route, steering to avoid
land, shallow water, and other obstacles.‍
Deleting a Saved Track
1 Select Nav Info > Tracks > Saved Tracks.‍
2 Select a track.‍
3 Select Delete.‍
Deleting All Saved Tracks
Select Nav Info > Manage Data > Clear User Data > Saved
Tracks.‍
Retracing the Active Track
The track currently being recorded is called the active track.‍
1 Select Nav Info > Tracks > Follow Active Track.‍
2 Select an option:
• Select the time the active track began.‍
• Select Entire Log.‍
3 Review the course indicated by the colored line.‍
4 Follow the colored line, steering to avoid land, shallow water,
and other obstacles.‍
Clearing the Active Track
Select Nav Info > Tracks > Clear Active Track.‍
The track memory is cleared, and the active track continues
to be recorded.‍
Managing the Track Log Memory During Recording
1 Select Nav Info > Tracks > Active Track Options.‍
2 Select Record Mode.‍
3 Select an option:
• To record a track log until the track memory is full, select
Fill.‍
• To continuously record a track log, replacing the oldest
track data with new data, select Wrap.‍
Configuring the Recording Interval of the Track Log
You can indicate the frequency at which the track plot is
recorded.‍ Recording more frequent plots is more accurate but
fills the track log faster.‍ The resolution interval is recommended
for the most efficient use of memory.‍
1 Select Nav Info > Tracks > Active Track Options > Record
Interval > Interval.‍
Combinations
Deleting All Saved Waypoints, Routes, and
Tracks
Select Nav Info > Manage Data > Clear User Data > All >
OK.‍
Combinations
The Combination screen shows a combination of different
screens at the same time.‍ The number of options available on
the Combination screen depends on the optional devices you
have connected to your chartplotter and whether you are using
premium maps.‍
Selecting a Combination
1 Select Combinations.‍
2 Select a combination.‍
Customizing a Combination Screen
1
2
3
4
Select Combinations.‍
Select a combination.‍
Select Menu.‍
Select an option:
• To change the name, select Name, and enter a new
name.‍
• To customize the data shown on the screen, select
Overlay Numbers.‍
Creating a Custom Combination Screen
You can create a custom Combination screen to suit your
needs.‍
1 Select Combinations > Customize > Add.‍
2 If necessary, select a layout and adjust the size of each
screen.‍
3 Select the data to display in the combination.‍
4 If necessary, select Done.‍
5 Enter a name for the combination.‍
Gauges and Almanac Information
Gauges provide various information about the trip, engine,
environment, and wind, and are available on all chartplotter
models.‍ Numbers, Compass, and Trip gauges are available on
all chartplotters.‍ Wind and Environment gauges require valid
wind data from the NMEA® 0183 or NMEA 2000 network.‍
Engine gauges require a connection to the NMEA 2000
network, so they are not available on all chartplotter models.‍
The chartplotters also provide almanac information about tides,
currents, and the sun and moon, such as rise and set times.‍
Viewing the Compass
You can view information about your bearing, heading, and
route using the compass.‍
Select Gauges > Compass.‍
11
Viewing Trip Gauges
Trip gauges show information for odometer, speed, time, and
fuel for your present trip.‍
Select Gauges > Trip Data.‍
Resetting Trip Gauges
1 Select Gauges > Trip Data > Menu.‍
2 Select an option:
• To set all the readings for the present trip to zero, select
Reset Trip.‍
• To set the maximum speed reading to zero, select Reset
Maximum Speed.‍
• To set the odometer reading to zero, select Reset
Odometer.‍
• To set all the readings to zero, select Reset All.‍
Viewing Engine and Fuel Gauges
Before you can view engine and fuel gauges, you must be
connected to a NMEA 2000 network capable of sensing engine
and fuel data.‍ See the installation instructions for details.‍
Select Gauges > Engine.‍
Customizing Engine Gauge and Fuel Gauge Limits
You can configure the upper and lower limits and the range of
desired standard operation of a gauge.‍ When a value exceeds
the range of standard operation, the gauge becomes red.‍
NOTE: Not all options are available for all gauges.‍
1 From the engine gauges screen, select Menu > Gauge
Setup > Set Gauge Limits.‍
2 Select a gauge.‍
3 Select Gauge Limits > Custom > Edit Limits.‍
4 Select an option:
• To set the minimum value of the standard operating
range, select Rated Min.‍.‍
• To set the maximum value of the standard operating
range, select Rated Max.‍.‍
• To set the lower limit of the gauge lower than the rated
minimum, select Scale Min.‍.‍
• To set the upper limit of the gauge higher than the rated
maximum, select Scale Max.‍.‍
5 Select the limit value.‍
6 Repeat steps 4 and 5 to set additional gauge limits.‍
Enabling Status Alarms for Engine Gauges
Customizing the Engines Shown in Gauges
Before you can customize how the engines are shown in the
gauges, you must manually select the number of engines
(Selecting the Number of Engines Shown in Gauges).‍
1 From the engine gauges screen, select Menu > Gauge
Setup > Engine Selection > Edit Engines.‍
Select
First Engine.‍
2
3 Select the engine to display in the first gauge.‍
4 Repeat for the remaining engine bars.‍
Configuring the Fuel Gauges Display
Before you can configure and display the fuel levels, a
compatible fuel flow sensor or tank level sensors must be
connected to the NMEA 2000 network.‍
You can display the total amount of fuel on-board either as a
numeric display that shows the total fuel or as a graphic display
that shows the level in each fuel tank.‍
1 Select Gauges > Engine > Menu > Gauge Setup > Fuel
Display.‍
2 Select an option:
• To display a numeric value for the total fuel level in all
tanks, select Use Total Fuel Onboard.‍
• To display a graphical representation of the amount of
fuel in each tank, select Use Fuel Tank Levels.‍
Setting the Fuel Capacity of the Vessel
1 Select Settings > My Vessel > Fuel Capacity.‍
2 Enter the combined total capacity of the fuel tanks.‍
Synchronizing the Fuel Data with the Actual Vessel
Fuel
You can synchronize the fuel levels in the chartplotter with the
actual fuel in the vessel when you add fuel to your vessel.‍
1 Select Gauges > Engine > Menu.‍
2 Select an option:
• After you have filled up all the fuel tanks on the vessel,
select Fill Up All Tanks.‍ The fuel level is reset to
maximum capacity.‍
• After you have added less than a full tank of fuel, select
Add Fuel to Boat, and enter the amount added.‍
• To specify the total fuel in the vessel tanks, select Set
Total Fuel Onboard, and enter the total amount of fuel in
the tanks.‍
Setting the Fuel Alarm
You can enable the chartplotter to display engine status alarms.‍
From the engine gauges screen, select Menu > Gauge
Setup > Status Alarms > On.‍
When an engine alarms is triggered, a gauge status alarm
message appears and the gauge may become red depending
on the type of alarm.‍
Before you can set a fuel level alarm, a compatible fuel flow
sensor must be connected to the NMEA 2000 network.‍
You can set an alarm to sound when the total amount of
remaining onboard fuel reaches the level you specify.‍
1 Select Settings > Alarms > Fuel > Fuel Alarm > On.‍
2 Enter the remaining amount of fuel that triggers the alarm.‍
Enabling Some Engine Gauge Status Alarms
1 From the engine gauges screen, select Menu > Gauge
Viewing the Wind Gauges
Setup > Status Alarms > Custom.‍
2 Select one or more engine gauge alarms to turn on or off.‍
Before you can view wind information, you must have a wind
sensor connected to the chartplotter.‍
Select Gauges > Wind.‍
Selecting the Number of Engines Shown in Gauges
Configuring the Speed Source
You can show information for up to four engines.‍
1 From the engine gauges screen, select Menu > Gauge
Setup > Engine Selection > Num.‍ Engines.‍
2 Select an option:
• Select the number of engines.‍
• Select Auto Configure to automatically detect the
number of engines.‍
12
You can specify whether the vessel speed data displayed on
the gauge and used for wind calculations is based on water
speed or GPS speed.‍
1 Select Gauges > Wind > Menu > Speed Display.‍
2 Select an option:
• To calculate the vessel speed based on data from the
water-speed sensor, select Water Speed.‍
Gauges and Almanac Information
• To calculate the vessel speed based on GPS data, select
GPS Speed.‍
Configuring the Heading Source of the Wind Gauge
You can specify the source of the heading displayed on the
wind gauge.‍ Magnetic heading is the heading data received
from a heading sensor, and GPS heading is calculated by your
chartplotter GPS (course over ground).‍
1 Select Gauges > Wind > Menu > Heading Source.‍
2 Select GPS Hdg or Magnetic.‍
Selecting the Range of the Close-Hauled Wind Gauge
You can specify the range of the close-hauled wind gauge for
both the upwind scale and the downwind scale.‍
1 Select Gauges > Wind > Menu.‍
2 Select an option:
• To set the maximum and minimum values that appear
when the upwind close-hauled wind gauge appears,
select Change Upwind Scale, and set the angles.‍
• To set the maximum and minimum values that appear
when the downwind close-hauled wind gauge appears,
select Change Downwind Scale, and set the angles.‍
Viewing the Environment Gauges
Select Gauges > Environment.‍
Configuring the Alignment of the Wind Gauge
You can specify the alignment of the wind gauge on the
environment gauges.‍
1 Select Gauges > Environment > Menu > Alignment.‍
2 Select an option:
• To set the top of the wind gauge to a North heading,
select North Up.‍
• To rotate the gauge so the direction in which you are
moving is at the top, select Head Up.‍
Configuring the Heading Source of the Environment
Gauge
You can specify the source of the heading displayed on the
environment gauge.‍ Magnetic heading is the heading data
received from a heading sensor, and GPS heading is calculated
by your chartplotter GPS (course over ground).‍
1 Select Gauges > Environment > Menu > Heading Source.‍
2 Select GPS Hdg or Magnetic.‍
Setting the Barometer Reference Time
You can specify the reference time used to calculate the
barometer trend.‍ The trend is indicated in the barometer field.‍
1 Select Gauges > Environment > Menu > Pressure Ref.‍
Time.‍
2 Select an option.‍
Tide, Current, and Celestial Information
Tide Station Information
You can view information about a tide station for a specific date
and time, including the tide height, and when the next high and
low tides will occur.‍ By default, the chartplotter shows tide
information for the most recently viewed tide station and for the
present date and time.‍
Select Nav Info > Tides & Currents > Tides.‍
Current Station Information
NOTE: Current station information is available with certain
detailed maps.‍
You can view information about a current station for a specific
date and time, including the current speed and level of the
Sonar
current.‍ By default, the chartplotter shows current information
for the most recently viewed current station and for the present
date and time.‍
Select Nav Info > Tides & Currents > Currents.‍
Celestial Information
You can view information about sunrise, sunset, moonrise,
moonset, moon phase, and the approximate sky view location
of the sun and moon.‍ The center of the screen represents the
sky overhead, and the outermost rings represent the horizon.‍
By default, the chartplotter shows celestial information for the
present date and time.‍
Select Nav Info > Tides & Currents > Celestial.‍
Viewing Tide Station, Current Station, or Celestial
Information for a Different Date
1 Select Nav Info > Tides & Currents.‍
2 Select Tides, Currents, or Celestial.‍
3 Select an option.‍
• To view information for a different date, select Change
Date > Manual, and enter a date.‍
• To view information for today, select Change Date >
Current.‍
• If available, to view information for the day after the date
shown, select Next Day.‍
• If available, to view information for the day before the date
shown, select Previous Day.‍
Viewing Information for a Different Tide or Current
Station
1 Select Nav Info > Tides & Currents.‍
2 Select Tides or Currents.‍
3 Select Nearby Stations.‍
4 Select a station.‍
Viewing Almanac Information from the Navigation
Chart
1 From a chart or 3D chart view, select a location.‍
2 Select Information.‍
3 Select Tides, Currents, or Celestial.‍
Sonar
When properly connected to an optional Garmin sounder
module and a transducer, your compatible chartplotter can be
used as a fishfinder.‍ There are different sonar views to help you
view the fish in the area.‍
The adjustments you can make to each sonar view vary
depending on the view you are in and the chartplotter model,
sounder module, and transducer you have connected.‍
Sonar Views
The sonar views available vary depending on the type of
transducer and optional sounder module connected to the
chartplotter.‍ For example, you can view the DownVü screen
only if you have a DownVü transducer connected.‍
There are four basic styles of sonar views available: a fullscreen view, a split-screen view that combines two or more
views such as Traditional and DownVü, a split-zoom view, and
a split-frequency view that displays two different frequencies.‍
You can customize the settings for each view in the screen.‍ For
example, if you are viewing the Split Frequency view, you can
adjust the gain for each of the frequencies separately.‍
If you do not see an arrangement of sonar views to suit your
needs, you can create a custom Combination screen (Creating
a Custom Combination Screen).‍
13
Full-Screen Sonar View
There are several full-screen views available, depending on the
equipment connected.‍ The full-screen sonar views show a large
image of the sonar readings from a transducer.‍ The range scale
along the right side of the screen shows the depth of detected
objects as the screen scrolls from the right to the left.‍
À
Á
Â
Depth information
Suspended targets or fish
Bottom of the body of water
DownVü Sonar View
NOTE: Not all models support DownVü sonar technology and
transducers.‍
NOTE: To receive DownVü scanning sonar, you need a
compatible chartplotter or fishfinder and a compatible
transducer.‍
DownVü high-frequency sonar provides a clearer picture below
the boat, providing a more detailed representation of structures
the boat is passing over.‍
Traditional transducers emit a conical beam.‍ The DownVü
scanning sonar technology emits a narrow beam, similar to the
shape of the beam in a copying machine.‍ This beam provides a
clearer, picture-like image of what is beneath the boat.‍
Split-Zoom Sonar View
The split-zoom sonar view shows a full-view graph of sonar
readings, and a magnified portion of that graph, on the same
screen.‍
Select Sonar > Split Zoom.‍
Split-Frequency Sonar View
In the split-frequency sonar view, one side of the screen shows
a full-view graph of high frequency sonar data, and the other
side of the screen shows a full-view graph of lower frequency
sonar data.‍
NOTE: The split-frequency sonar view requires the use of a
dual-frequency transducer.‍
Select Sonar > Split Frequency.‍
Pausing the Sonar Display
From a Sonar view, select Menu > Pause Sonar.‍
SideVü Sonar View
Creating a Waypoint on the Sonar Screen
NOTE: Not all models support SideVü sonar and scanning
transducers.‍
NOTE: To receive SideVü scanning sonar, you need a
compatible chartplotter, a compatible sounder module, and a
compatible transducer.‍
SideVü scanning sonar technology shows you a picture of what
lies to the sides of the boat.‍ You can use this as a search tool to
find structures and fish.‍
1 From a sonar view, select Menu > Pause Sonar.‍
2 Select the location of the waypoint.‍
3 Select New Wpt.‍
Viewing Sonar History
You can scroll the sonar display to view historical sonar data.‍
1 From a sonar view, select Menu > Pause Sonar.‍
2 Drag the screen or use the arrow keys.‍
Adjusting the Level of Detail
À
Á
Â
Ã
Ä
Å
Æ
Left side of the boat
Right side of the boat
The transducer on your vessel
Trees
Old tires
Logs
Distance from the side of the boat
SideVü/DownVü Scanning Technology
Instead of a more common conical beam, the SideVü/DownVü
transducer uses a flat beam to scan the water and ground to the
sides of your boat.‍
14
You can control the level of detail and noise shown on the sonar
screen either by adjusting the gain for traditional transducers, or
by adjusting the brightness for DownVü and SideVü/DownVü
transducers.‍
If you want to see the highest intensity signal returns on the
screen, you can lower the gain or brightness to remove lower
intensity returns and noise.‍ If you want to see all return
information, you can increase the gain or brightness to see
more information on the screen.‍ This also increases noise, and
can make it more difficult to recognize actual returns.‍
1 From a sonar view, select Menu.‍
2 Select Gain or Brightness.‍
3 Select an option:
• To increase or decrease the gain or brightness manually,
select Up or Down.‍
• To allow the chartplotter to adjust the gain or brightness
automatically, select an automatic option.‍
Adjusting the Color Intensity
You can adjust the intensity of colors and highlight areas of
interest on the sonar screen by adjusting the color gain for
Sonar
traditional transducers or the contrast for DownVü and SideVü/
DownVü transducers.‍ This setting works best after you have
adjusted the level of detail shown on the screen using the gain
or brightness settings.‍
If you want to highlight smaller fish targets or create a higher
intensity display of a target, you can increase the color gain or
contrast setting.‍ This causes a loss in the differentiation of the
high intensity returns at the bottom.‍ If you want to reduce the
intensity of the return, you can reduce the color gain or contrast.‍
1 From a sonar view, select Menu.‍
2 Select an option:
• While in the DownVü or SideVü sonar view, select
Contrast.‍
• While in another sonar view, select Sonar Setup >
Advanced > Color Gain.‍
Select
an option:
3
• To increase or decrease the color intensity manually,
select Up or Down.‍
• To use the default setting, select Default.‍
Adjusting the Range of the Depth or Width
Scale
You can adjust the range of the depth scale traditional and
DownVü sonar views and the range of the width scale for the
SideVü sonar view.‍
Allowing the device to adjust the range automatically keeps the
bottom within the lower or outer third of the sonar screen, and
can be useful for tracking a bottom that has minimal or
moderate terrain changes.‍
Manually adjusting the range enables you to view a specified
range, which can be useful for tracking a bottom that has large
terrain changes, such as a drop-offs or cliffs.‍ The bottom can
appear on the screen as long as it appears within the range you
have set.‍
1 From a sonar view, select Menu > Range.‍
2 Select an option:
• To allow the chartplotter to adjust the range automatically,
select Auto.‍
• To increase or decrease the range of the range manually,
select Up or Down.‍
TIP: From the sonar screen, you can select or to
manually adjust the range.‍
Setting the Zoom Level on the Sonar Screen
1 From a sonar view, select Menu > Zoom.‍
2 Select an option:
• To zoom in on the sonar data from the bottom depth,
select Bottom Lock.‍
• To set the depth range of the magnified area manually,
select Manual, select View Up or View Down to set the
depth range of the magnified area, and select Zoom In or
Zoom Out to increase or decrease the magnification of
the magnified area.‍
• To set the depth and zoom automatically, select Auto.‍
• To cancel the zoom, select No Zoom.‍
Sonar Frequencies
NOTE: The frequencies available depend on the chartplotter,
sounder modules, and transducer being used.‍
Adjusting the frequency helps adapt the sonar for your particular
goals and the present depth of the water.‍
Higher frequencies use narrow beam widths, and are better for
high-speed operation and rough sea conditions.‍ Bottom
Sonar
definition and thermocline definition can be better when using a
higher frequency.‍
Lower frequencies use wider beam widths, which can let the
fisherman see more targets, but could also generate more
surface noise and reduce bottom signal continuity during rough
sea conditions.‍ Wider beam widths generate larger arches for
fish target returns, making them ideal for locating fish.‍ Wider
beam widths also perform better in deep water, because the
lower frequency has better deep water penetration
Chirp frequencies allow you to sweep each pulse through a
range of frequencies, resulting in better target separation in
deep water.‍ Chirp can be used to distinctly identify targets, like
individual fish in a school, and for deep water applications.‍
Chirp generally performs better than single frequency
applications.‍ Because some fish targets may show up better
using a fixed frequency, you should consider your goals and
water conditions when using Chirp.‍
Some sonar black boxes and transducers also provide the
ability to customize preset frequencies for each transducer
element, which enables you to change the frequency quickly
using the presets as the water and your goals change.‍
Viewing two frequencies concurrently using the Split Frequency
view, allows you to see deeper with the lower frequency return
and at the same time see more detail from the higher frequency
return.‍
Selecting Frequencies
NOTE: You cannot adjust the frequency for all sonar views and
transducers.‍
You can indicate which frequencies appear on the sonar
screen.‍
1 From a sonar view, select Menu > Frequency.‍
2 Select a frequency suited to your needs and water depth.‍
For more information on frequencies, see Sonar
Frequencies.‍
Creating a Frequency Preset
NOTE: Not available with all transducers.‍
You can create a preset to save a specific sonar frequency,
which allows you to change frequencies quickly.‍
1 From a sonar view, select Menu > Frequency.‍
2 Select Add.‍
3 Enter a frequency.‍
Turning On the A-Scope
NOTE: This feature is not available in all sonar views.‍
The a-scope is a vertical flasher along the right side of the fullscreen sonar view.‍ This feature expands the most recently
received sonar data so that it is easier to see.‍ It can also be
helpful for detecting fish that are close to the bottom.‍
From a sonar view, select Menu > Sonar Setup >
Appearance > A-Scope.‍
Selecting the Transducer Type
Before you can select the transducer type, you must know what
kind of transducer you have.‍
If you are connecting a transducer that was not included with
the chartplotter, you may need to set the transducer type to
make the sonar function properly.‍ If the device automatically
detected your transducer, this option does not appear.‍
1 From a sonar view, select Menu > Sonar Setup >
Installation > Transducer Type.‍
2 Select an option:
• If you have a 200/77 kHz, dual-beam transducer, select
Dual Beam.‍
15
• If you have a 200/50 kHz, dual-frequency transducer,
select Dual Frequency.‍
• If you have another type of transducer, select it from the
list.‍
Sonar Setup
Sonar Settings
NOTE: Not all options and settings apply to all models, sounder
modules, and transducers.‍
From a sonar view, select Menu > Sonar Setup.‍
Depth Line: Shows a quick-reference depth line.‍
Scroll Speed: Sets the rate at which the sonar scrolls from right
to left.‍
In shallow water you might want to slow the scroll speed to
extend the length of time the information is displayed on
screen.‍ In deeper water you might want to increase the scroll
speed.‍
On-screen Control: Sets what the buttons on the sonar screen
control.‍ This is available for touchscreen devices.‍
Range Lines: Shows the vertical lines indicating the distance to
the right and left of the boat.‍ Available for SideVü sonar view.‍
Color Scheme: Sets the color scheme of the sonar view.‍ This
setting might be available in the Appearance menu.‍
The high contrast color schemes provide darker color
assignments to the low intensity returns.‍ The low contrast
color schemes provide color assignments to the low intensity
returns that are similar to the background color.‍
Appearance: See Sonar Appearance Settings.‍
Overlay Numbers: Sets the data shown on the sonar screen.‍
Advanced: See Advanced Sonar Settings.‍
Installation: Restores the default sonar settings.‍
Sonar Appearance Settings
NOTE: Not all options and settings apply to all models, sounder
modules, and transducers.‍
From a Sonar view, select Menu > Sonar Setup >
Appearance.‍
Color Scheme: Sets the color scheme.‍
Edge: Highlights the strongest signal from the bottom to help
define the hardness or softness of the signal.‍
A-Scope: Displays a vertical flasher along the right side of the
screen that shows instantaneously the range to targets along
a scale.‍
Pic.‍ Advance: Allows the sonar picture to advance faster by
drawing more than one column of data on the screen for
each column of sounder data received.‍ This is especially
helpful when you are using the sounder in deep water,
because the sonar signal takes longer to travel to the water
bottom and back to the transducer.‍
The 1/1 setting draws one column of information on the
screen per sounder return.‍ The 2/1 setting draws two
columns of information on the screen per sounder return,
and so on for the 4/1 and 8/1 settings.‍
Fish Symbols: Sets how the sonar interprets suspended
targets.‍
Advanced Sonar Settings
NOTE: Not all options and settings apply to all models, sounder
modules, and transducers.‍
From a sonar view, select Menu > Sonar Setup > Advanced.‍
Interference: Adjusts the sensitivity to reduce the effects of
interference from nearby sources of noise.‍
16
The lowest interference setting that achieves the desired
improvement should be used to remove interference from the
screen.‍ Correcting installation issues that cause noise is the
best way to eliminate interference.‍
Surface Noise: Hides surface noise to help reduce clutter.‍
Wider beam widths (lower frequencies) can show more
targets, but can generate more surface noise.‍
Color Gain: See Adjusting the Level of Detail.‍
TVG: Adjusts the appearance of returns to compensate for
weakened sonar signals in deeper water, and reduces the
appearance of noise near the surface.‍ When the value of this
setting is increased, the colors associated with low-level
noise and fish targets appear more consistent through
various water depths.‍ This setting also reduces the noise
near the surface of the water.‍
Sonar Installation Settings
NOTE: Not all options and settings apply to all models, sounder
modules, and transducers.‍
From a sonar view, select Menu > Sonar Setup > Installation.‍
Restore Sonar Defaults: Restores the factory default settings
for the sonar view.‍
Transducer Type: Allows you to select the type of transducer
that is connected to the device.‍
Flip Left/Right: Changes the orientation of the SideVü sonar
view when the transducer is installed backward.‍
Sonar Alarm Settings
NOTE: Some settings require external accessories.‍
Select Settings > Alarms > Sonar.‍
Shallow Water: Sets an alarm to sound when the depth is less
than the specified value.‍
Deep Water: Sets an alarm to sound when the depth is greater
than the specified value.‍
Water Temp.‍: Sets an alarm to sound when the transducer
reports a temperature that is 2°F (1.‍1°C) above or below the
specified temperature.‍
Sonar Recordings
Recording the Sonar Display
NOTE: Not all models support sonar recording.‍
1 Insert a memory card into the card slot.‍
2 From a Sonar view, select Menu > Record Sonar.‍
Stopping the Sonar Recording
Before you can stop recording the sonar, you must begin
recording it (Recording the Sonar Display).‍
From a sonar view, select Menu > Stop Recording.‍
Deleting a Sonar Recording
1 Insert a memory card into the card slot.‍
2 Select Sonar > Sonar Recordings.‍
3 Select a recording.‍
4 Select Delete.‍
Depth and Water Temperature Graphs
If you are using a depth-capable transducer, or are receiving
water depth information over NMEA 0183 or NMEA 2000, you
can view a graphic log of depth readings over time.‍ If you are
using a temperature-capable transducer, or are receiving water
temperature information over NMEA 0183 or NMEA 2000, you
can view a graphic log of temperature readings over time.‍
The graphs scroll to the left as information is received.‍
Select Sonar > Data Graphs.‍
Sonar
Setting the Depth and Water Temperature Graph
Range and Time Scales
You can indicate the amount of time and the range of depth that
appear in the depth and water temperature graphs.‍
1 Select Sonar > Data Graphs > Menu.‍
2 Select Depth Graph Settings or Temperature Graph
Settings.‍
3 Select an option:
• To set a time-elapsed scale, select Duration.‍ The default
setting is 10 minutes.‍ Increasing the time-elapsed scale
allows you to view variations over a longer period of time.‍
Decreasing the time-elapsed scale allows you to view
more detail over a shorter period of time.‍
• To set the depth-range or temperature-range scale, select
Scale.‍ Increasing the scale allows you to view more
variation in readings.‍ Decreasing the scale allows you to
view more detail in the variation.‍
Radar
WARNING
The marine radar transmits microwave energy that has the
potential to be harmful to humans and animals.‍ Before
beginning radar transmission, verify that the area around the
radar is clear.‍ The radar transmits a beam approximately 12°
above and below a line extending horizontally from the center of
the radar.‍ Avoid looking directly at the radar, because the eyes
are the most susceptible parts of the body.‍
NOTE: Not all models support radar.‍
When you connect your compatible chartplotter to an optional
Garmin marine radar, such as a GMR™ 1206 xHD or a GMR 24
HD, you can view more information about your surroundings.‍
The GMR transmits a narrow beam of microwave energy as it
rotates to a 360° pattern.‍ When the transmitted energy contacts
a target, some of that energy is reflected back to the radar.‍
Radar Display Modes
NOTE: Not all modes are available with all radar devices and all
chartplotters.‍
Select Radar, and select a mode.‍
Cruising Mode: Shows a full-screen image of the gathered
radar information.‍
Harbor Mode: Intended for use in inland waters, this mode
works best with short-range signals (2 nm or less).‍
Offshore Mode: Intended for use in open waters, this mode
works best with long-range signals.‍
Sentry Mode: Allows you to put the radar into timed-transmit
mode, in which you can configure a radar transmit and
standby cycle to conserve power.‍ You can also enable a
guard zone in this mode, which identifies a safe zone around
your boat.‍ If you switch from Sentry mode to another mode,
the radar switches to full-time transmission and disables all
guard zones.‍
Radar Overlay Mode: Shows a full-screen image of the
gathered radar information on top of the Navigation chart.‍
The Radar overlay displays data based on the most recently
used radar mode.‍
Transmitting Radar Signals
NOTE: As a safety feature, the radar enters standby mode after
it warms up.‍ This gives you an opportunity to verify the area
around the radar is clear before beginning radar transmission.‍
1 With the chartplotter off, connect your radar as described in
the radar installation instructions.‍
Radar
2 Turn on the chartplotter.‍
The radar warms up and a countdown alerts you when the
radar is ready.‍
Select
Radar.‍
3
4 Select a radar mode.‍
A countdown message appears while the radar is starting up.‍
5 Select Menu > Transmit Radar.‍
Range of Radar Signals
The range of the radar signal indicates the length of the pulsed
signal transmitted and received by the radar.‍ As the range
increases, the radar transmits longer pulses in order to reach
distant targets.‍ Closer targets, especially rain and waves, also
reflect the longer pulses, which can add noise to the Radar
screen.‍ Viewing information about longer-range targets can also
decrease the amount of space available on the Radar screen
for viewing information about shorter-range targets.‍
Adjusting the Zoom Scale on the Radar
Screen
The radar zoom scale, also called the radar signal range,
represents the distance from your position (the center) to the
outermost ring.‍
From a Radar screen, select or .‍
Each ring represents an even division of the zoom scale.‍
For example, if the zoom scale is set at 3 miles, each ring
represents 1 mile from the center out.‍
Tips for Selecting a Radar Zoom Scale
The radar zoom scale, or radar signal range, indicates the
length of the pulsed signal transmitted and received by the
radar.‍ As the range increases, the radar transmits longer pulses
in order to reach distant targets.‍ Closer targets, especially rain
and waves, also reflect the longer pulses, which can add noise
to the Radar screen.‍ Viewing information about longer-range
targets can also decrease the amount of space available on the
Radar screen for viewing information about shorter-range
targets.‍
• Determine what information you need to see on the Radar
screen.‍
For example, do you need information about nearby weather
conditions or targets and traffic, or are you more concerned
about distant weather conditions?
• Assess the environmental conditions where the radar is
being used.‍
Especially in inclement weather, longer-range radar signals
can increase the clutter on the Radar screen and make it
more difficult to view information about shorter-range targets.‍
In rain, shorter-range radar signals can enable you to view
information about nearby objects more effectively, if the rain
clutter setting is configured optimally.‍
• Select the shortest effective range, given your reason for
using radar and the present environmental conditions.‍
Sentry Mode
Sentry mode allows you to put the radar into timed-transmit
mode, in which you can configure a radar transmit and standby
cycle to conserve power.‍ You can also enable a guard zone in
this mode, which identifies a safe zone around your boat and
sounds an alarm when a radar object enters the zone.‍ Sentry
mode works with all Garmin GMR model radars.‍
Enabling Timed Transmit
From the sentry screen, select Menu > Sentry Setup >
Timed Transmit > On.‍
17
Setting the Standby and Transmit Times
Before you can set the standby and transmit times, you must
enable timed transmit (Enabling Timed Transmit).‍
To help conserve power, you can indicate the radar standby
time and the transmit time to implement periodic radar signal
transmissions at set intervals.‍
1 From the sentry screen, select Menu > Sentry Setup.‍
2 Select Stdby Time.‍
3 Enter the time interval between radar signal transmissions.‍
4 Select Transmit Time.‍
5 Enter the duration of each radar signal transmission.‍
Enabling a Guard Zone
From the sentry screen, select Menu > Sentry Setup >
Enable Guard Zone.‍
Defining a Circular Guard Zone
Before you can define the boundaries of the guard zone, you
must enable a guard zone (Enabling a Guard Zone).‍
You can define a circular guard zone that completely
encompasses your boat.‍
1 From the sentry screen, select Menu > Sentry Setup >
Adjust Guard Zone > Move Radar Guard Zone > Circle.‍
Select the location of the outer guard zone circle.‍
2
3 Select the location of the inner guard zone circle to define
the width of the guard zone.‍
Defining a Partial Guard Zone
You can define the boundaries of a guard zone that does not
completely encompass your boat.‍
1 From the sentry screen, select Menu > Sentry Setup >
Adjust Guard Zone > Move Radar Guard Zone > Corner
1.‍
2 Touch and drag the location of the outer guard-zone corner
À.‍
configured for one radar mode, the setting is applied to every
other radar mode.‍ The details and projected heading settings
configured for one radar mode are applied to every other radar
mode and to the Radar overlay.‍
1 From a Radar screen or the Radar overlay, select Menu >
Other Vessels > Display Setup.‍
2 Select an option:
• To indicate the distance from your location within which
AIS vessels appear, select AIS Display Range, and
select a distance.‍
• To show details about AIS-activated vessels, select
Details > Show.‍
• To set the projected heading time for AIS-activated
vessels, select Projected Heading, and enter the time.‍
• To show the tracks of AIS vessels, select Trails, and
select the length of the track that appears.‍
VRM and EBL
The variable range marker (VRM) and the electronic bearing
line (EBL) measure the distance and bearing from your boat to
a target object.‍ On the Radar screen, the VRM appears as a
circle that is centered on the present location of your boat, and
the EBL appears as a line that begins at the present location of
your boat and intersects the VRM.‍ The point of intersection is
the target of the VRM and the EBL.‍
Showing the VRM and the EBL
The VRM and the EBL configured for one mode are applied to
all other radar modes.‍
From a Radar screen, select Menu > Show VRM/EBL.‍
Adjusting the VRM and the EBL
Before you can adjust the VRM and the EBL, you must show
them on the Radar screen (Showing the VRM and the EBL).‍
You can adjust the diameter of the VRM and the angle of the
EBL, which moves the intersection point of the VRM and the
EBL.‍ The VRM and the EBL configured for one mode are
applied to all other radar modes.‍
1 From a Radar screen, select a new location for the
intersection point of the VRM and the EBL.‍
2 Select Drop VRM/EBL.‍
3 Select Stop Panning.‍
Measuring the Range and Bearing to a Target Object
3 Select Corner 2.‍
4 Touch the location of the inner guard-zone corner Á to
define the width of the guard zone.‍
Marking a Waypoint on the Radar Screen
1 From a Radar screen or the Radar overlay, select a location.‍
2 Select New Waypoint.‍
Viewing a List of AIS Threats
From any Radar screen or the Radar overlay, you can view and
customize the appearance of a list of AIS threats.‍
From a Radar screen or the Radar overlay, select Menu >
Other Vessels > AIS List.‍
Showing AIS Vessels on the Radar Screen
AIS requires the use of an external AIS device and active
transponder signals from other vessels.‍
You can configure how other vessels appear on the Radar
screen.‍ If any setting (except the AIS display range) is
18
Before you can adjust the VRM and the EBL, you must show
them on the Radar screen (Showing the VRM and the EBL).‍
1 From a Radar screen, select the target location.‍
2 Select Measure Distance.‍
The range and the bearing to the target location appear in
the upper-left corner of the screen.‍
Radar Overlay
When you connect your chartplotter to an optional Garmin
marine radar, you can use the Radar overlay to overlay radar
information on the Navigation chart or on the Fishing chart.‍
The Radar overlay superimposes radar information on the
Navigation chart or the Fishing chart.‍ Data appears on the
Radar overlay based on the most recently used radar mode
(such as Harbor, Offshore, or Sentry), and all settings
configurations applied to the Radar overlay are also applied to
the last-used radar mode.‍ For example, if you use Harbor mode
and then you switch to the Radar overlay, the Radar overlay
would show Harbor mode radar data.‍ If you changed the gain
setting using the Radar overlay menu, the gain setting for
Harbor mode would change automatically.‍
Radar
Radar Overlay and Chart Data Alignment
When using the Radar overlay, the chartplotter aligns radar data
with chart data based on the boat heading, which is based by
default on data from a magnetic heading sensor connected
using a NMEA 0183 or NMEA 2000 network.‍ If a heading
sensor is not available, the boat heading is based on GPS
tracking data.‍
GPS tracking data indicates the direction in which the boat is
moving, not the direction in which the boat is pointing.‍ If the
boat is drifting backward or sideways due to a current or wind,
the Radar overlay may not perfectly align with the chart data.‍
This situation should be avoided by using boat-heading data
from an electronic compass.‍
If the boat heading is based on data from a magnetic heading
sensor or an automatic pilot, the heading data could be
compromised due to incorrect setup, mechanical malfunction,
magnetic interference, or other factors.‍ If the heading data is
compromised, the Radar overlay may not align perfectly with
the chart data.‍
Showing the Radar Overlay
The Radar overlay displays data based on the most recently
used radar mode.‍
From a Radar screen, select Menu > 8xxx > Radar Overlay.‍
The radar picture appears in orange and overlays the
Navigation chart.‍
Stopping the Transmission of Radar Signals
From a Radar screen, select Menu > Radar to Standby.‍
Optimizing the Radar Display
You can adjust the radar display settings for reduced clutter and
increased accuracy.‍
NOTE: You can optimize the radar display for each radar mode.‍
1 Select a radar range (Range of Radar Signals).‍
2 Restore the default value of the gain setting ( Adjusting Gain
on the Radar Screen Automatically).‍
3 Adjust the gain setting manually ( Adjusting Gain on the
Radar Screen Manually).‍
Radar Gain and Clutter
Adjusting Gain on the Radar Screen Automatically
The automatic gain setting for each radar mode is optimized for
that mode, and may differ from the automatic gain setting used
for another mode.‍
NOTE: Depending upon the radar in use, the gain setting
configured for use in one radar mode may or may not be
applied to other radar modes or to the Radar overlay.‍
NOTE: Not all options and settings are available on all radar
and chartplotter models.‍
1 From a Radar screen or the Radar overlay, select Menu >
Gain.‍
2 Select an available option:
• Select Auto.‍
The chartplotter sets the gain automatically once, based
on average conditions, the range of the radar signal, and
the selected radar mode.‍ The chartplotter does not adjust
the gain automatically in response to changing conditions.‍
• Select Auto Harbor or Auto Offshore.‍
The chartplotter automatically adjusts the gain for the
conditions.‍
Adjusting Gain on the Radar Screen Manually
For optimal radar performance, you can manually adjust the
gain.‍
Radar
NOTE: Depending upon the radar in use, the gain setting
configured for use in one radar mode may or may not be
applied to other radar modes or to the Radar overlay.‍
1 From a Radar screen or the Radar overlay, select Menu >
Gain.‍
Select
Up to raise the gain, until light speckles appear across
2
the Radar screen.‍
Data on the Radar screen is refreshed every few seconds.‍
As a result, the effects of manually adjusting the gain may
not appear instantly.‍ Adjust the gain slowly.‍
Select
Down to lower the gain until the speckles disappear.‍
3
4 If boats, land, or other targets are within range, select Down
to lower the gain until the targets begin to blink.‍
Select
Up to raise the gain until the boats, land, or other
5
targets appear steadily lit on the Radar screen.‍
6 Minimize the appearance of nearby large objects, if
necessary.‍
7 Minimize the appearance of side-lobe echoes, if necessary.‍
Minimizing Nearby Large-Object Interference
Nearby targets of significant size, such as jetty walls, can cause
a very bright image of the target to appear on the Radar screen.‍
This image can obscure smaller targets located near it.‍
NOTE: Depending upon the radar in use, the gain setting
configured for use in one radar mode may or may not be
applied to other radar modes or to the Radar overlay.‍
1 From a Radar screen or the Radar overlay, select Menu >
Gain.‍
2 Select Down to lower the gain until the smaller targets are
clearly visible on the Radar screen.‍
Reducing the gain to eliminate nearby large-object
interference may cause smaller or distant targets to blink or
disappear from the Radar screen.‍
Minimizing Side-Lobe Interference on the Radar Screen
Side-lobe interference may appear to streak outward from a
target in a semi-circular pattern.‍ Side-lobe effects can be
avoided by reducing the gain or reducing the radar range.‍
NOTE: Depending upon the radar in use, the gain setting
configured for use in one radar mode may or may not be
applied to other radar modes or to the Radar overlay.‍
1 From a Radar screen or the Radar overlay, select Menu >
Gain.‍
2 Select Down to lower the gain until the semi-circular,
streaked pattern disappears from the Radar screen.‍
Reducing the gain to eliminate side-lobe interference may
cause smaller or distant targets to blink or disappear from
the Radar screen.‍
Adjusting Sea Clutter on the Radar Screen Automatically
You can set the chartplotter to automatically adjust the
appearance of clutter caused by choppy sea conditions.‍
NOTE: Depending upon the radar in use, the sea clutter setting
configured for use in one radar mode may or may not be
applied to other radar modes or to the radar overlay.‍
NOTE: Not all options and settings are available on all radar
and chartplotter models.‍
1 From a radar screen or the radar overlay, select Menu >
Noise Rejection > Sea Clutter.‍
2 Select Presets or Auto.‍
3 Select a setting that reflects the present sea conditions.‍
When using a compatible radar model, the chartplotter adjusts
the sea clutter based on the sea conditions automatically.‍
Adjusting Sea Clutter on the Radar Screen Manually
You can adjust the appearance of clutter caused by choppy sea
conditions.‍ The sea clutter setting affects the appearance of
19
nearby clutter and targets more than it affects the appearance
of distant clutter and targets.‍ A higher sea clutter setting
reduces the appearance of clutter caused by nearby waves, but
it can also reduce or eliminate the appearance of nearby
targets.‍
NOTE: Depending upon the radar in use, the sea clutter setting
configured for use in one radar mode may or may not be
applied to other radar modes or to the Radar overlay.‍
1 From a Radar screen or the Radar overlay, select Menu >
Noise Rejection > Sea Clutter.‍
2 Select Up or Down to adjust the appearance of sea clutter
until other targets are clearly visible on the Radar screen.‍
Clutter caused by sea conditions may still be visible.‍
Adjusting Rain Clutter on the Radar Screen
You can adjust the appearance of clutter caused by rain.‍
Reducing the radar range also can minimize rain clutter
(Adjusting the Zoom Scale on the Radar Screen).‍
The rain clutter setting affects the appearance of nearby rain
clutter and targets more than it affects the appearance of distant
rain clutter and targets.‍ A higher rain clutter setting reduces the
appearance of clutter caused by nearby rain, but it can also
reduce or eliminate the appearance of nearby targets.‍
NOTE: Depending upon the radar in use, the rain clutter
settings configured for use in one radar mode may or may not
be applied to other radar modes or to the Radar overlay.‍
1 From a Radar screen or the Radar overlay, select Menu >
Noise Rejection > Rain Clutter.‍
2 Select Up or Down to decrease or increase the appearance
of nearby rain clutter until other targets are clearly visible on
the Radar screen.‍
Clutter caused by rain may still be visible.‍
Reducing Cross Talk Clutter on the Radar Screen
You can reduce the appearance of clutter caused by
interference from another nearby radar source, when the cross
talk reject setting is on.‍
NOTE: Depending upon the radar in use, the cross talk reject
setting configured for use in one radar mode may or may not be
applied to other radar modes or to the Radar overlay.‍
From a Radar screen or the Radar overlay, select Menu >
Noise Rejection > Cross Talk Reject.‍
Radar Display Settings
From any Radar screen or the Radar overlay, select Menu >
Radar Setup.‍
Orientation: Sets the perspective of the radar display.‍ The
orientation setting applies to every radar mode.‍ This setting
does not apply to the Radar overlay.‍
Appearance: Sets the color scheme, look-ahead speed, and
navigation appearance.‍
Front of Boat: Compensates for the physical location of the
radar scanner on a boat, if the radar scanner does not align
with the bow-stern axis.‍
Radar Appearance Settings
From a Radar screen, select Menu > Radar Setup >
Appearance.‍
NOTE: These settings do not apply to the Radar overlay.‍
Color Scheme: Sets the color scheme.‍
Look-Ahead Speed: Shifts your present location toward the
bottom of the screen automatically as your speed increases.‍
Enter your top speed for the best results.‍
Heading Line: Shows an extension from the bow of the boat in
the direction of travel on the radar screen.‍
Rings: Shows the range rings that help you to visualize
distances on the radar screen.‍
20
Nav.‍ Lines: Shows the navigation lines that indicate the course
you have set using Route To, Guide To, or Go To.‍
Waypoints: Shows waypoints on the radar screen.‍
Front-of-Boat Offset
The front-of-boat offset compensates for the physical location of
the radar scanner on a boat, if the radar scanner does not align
with the bow-stern axis.‍
Measuring the Potential Front-of-Boat Offset
The front-of-boat offset compensates for the physical location of
the radar scanner on a boat, if the radar scanner does not align
with the bow-stern axis.‍
1 Using a magnetic compass, take an optical bearing of a
stationary target located within viewable range.‍
Measure the target bearing on the radar.‍
2
3 If the bearing deviation is more than +/- 1°, set the front-ofboat offset.‍
Setting the Front-of-Boat Offset
Before you can set the front-of-boat offset, you must measure
the potential front-of-boat offset.‍
The front-of-boat offset setting configured for use in one radar
mode is applied to every other radar mode and to the Radar
overlay.‍
1 From a Radar screen or the Radar overlay, select Menu >
Radar Setup > Front of Boat.‍
2 Select Up or Down to adjust the offset.‍
Digital Selective Calling
Networked Chartplotter and VHF Radio
Functionality
If you have a NMEA 0183 VHF radio or a NMEA 2000 VHF
radio connected to your chartplotter, these features are
enabled.‍
• The chartplotter can transfer your GPS position to your radio.‍
If your radio is capable, GPS position information is
transmitted with DSC calls.‍
• The chartplotter can receive digital selective calling (DSC)
distress and position information from the radio.‍
• The chartplotter can track the positions of vessels sending
position reports.‍
If you have a Garmin NMEA 2000 VHF radio connected to your
chartplotter, these features are also enabled.‍
• The chartplotter allows you to quickly set up and send
individual routine call details to your Garmin VHF radio.‍
• When you initiate a man-overboard distress call from your
radio, the chartplotter shows the man-overboard screen and
prompts you to navigate to the man-overboard point.‍
• When you initiate a man-overboard distress call from your
chartplotter, the radio shows the Distress Call page to initiate
a man-overboard distress call.‍
Turning On DSC
Select Settings > Other Vessels > DSC.‍
DSC List
The DSC list is a log of the most recent DSC calls and other
DSC contacts you have entered.‍ The DSC list can contain up to
100 entries.‍ The DSC list shows the most recent call from a
boat.‍ If a second call is received from the same boat, it replaces
the first call in the call list.‍
Viewing the DSC List
Before you can view the DSC list, the chartplotter must be
connected to a VHF radio that supports DSC.‍
Digital Selective Calling
Select Nav Info > Other Vessels > DSC List.‍
Adding a DSC Contact
You can add a vessel to your DSC list.‍ You can make calls to a
DSC contact from the chartplotter.‍
1 Select Nav Info > Other Vessels > DSC List > Add
Contact.‍
2 Enter the Maritime Mobile Service Identity (MMSI) of the
vessel.‍
3 Enter the name of the vessel.‍
Incoming Distress Calls
If your compatible chartplotter and VHF radio are connected
using NMEA 0183 or NMEA 2000, your chartplotter alerts you
when your VHF radio receives a DSC distress call.‍ If position
information was sent with the distress call, that information is
also available and recorded with the call.‍
designates a distress call in the DSC list and marks the
position of the vessel on the Navigation chart at the time of the
DSC distress call.‍
Navigating to a Vessel in Distress
designates a distress call in the DSC list and marks the
position of a vessel on the Navigation chart at the time of the
DSC distress call.‍
1 Select Nav Info > Other Vessels > DSC List.‍
2 Select a position-report call.‍
3 Select Navigate To.‍
4 Select Go To or Route To.‍
Man-Overboard Distress Calls Initiated from a VHF
Radio
When the chartplotter is connected to a compatible VHF radio
with NMEA 2000, and you initiate a man-overboard DSC
distress call from the radio, the chartplotter shows the manoverboard screen and prompts you to navigate to the manoverboard point.‍ If you have a compatible autopilot system
connected to the network, the chartplotter prompts you to start a
Williamson’s turn to the man-overboard point.‍
If you cancel the man-overboard distress call on the radio, the
chartplotter screen prompting you to activate navigation to the
man-overboard location disappears.‍
Man-Overboard Distress Calls Initiated from the
Chartplotter
When your chartplotter is connected to a Garmin NMEA 2000
compatible radio and you activate navigation to a manoverboard location, the radio shows the Distress Call page so
you can quickly initiate a man-overboard distress call.‍
For information on placing distress calls from your radio, see the
VHF radio owner’s manual.‍ For information about marking an
MOB, see Marking and Starting Navigation to an MOB Location.‍
Position Tracking
When you connect the chartplotter to a VHF radio using NMEA
0183, you can track vessels that send position reports.‍ This
feature is also available with NMEA 2000, when the vessel
sends the correct PGN data (PGN 129808; DSC Call
Information).‍
Every position report call received is logged in the DSC list
(DSC List).‍
Viewing a Position Report
1 Select Nav Info > Other Vessels > DSC List.‍
2 Select a position-report call.‍
3 Select an option:
• To switch to position report details, select .‍
Digital Selective Calling
• To switch to a Navigation chart marking the location,
select .‍
• To switch to a Navigation chart marking the location,
select Next Page.‍
• To view the position report details, select Previous Page.‍
Navigating to a Tracked Vessel
1 Select Nav Info > Other Vessels > DSC List.‍
2 Select a position-report call.‍
3 Select Navigate To.‍
4 Select Go To or Route To.‍
Creating a Waypoint at the Position of a Tracked
Vessel
1 Select Nav Info > Other Vessels > DSC List.‍
2 Select a position-report call.‍
3 Select New Waypoint.‍
Editing Information in a Position Report
1 Select Nav Info > Other Vessels > DSC List.‍
2 Select a position-report call.‍
3 Select Edit.‍
•
•
•
•
To enter the name of the vessel, select Name.‍
To select a new symbol, select Symbol, if available.‍
To enter a comment, select Comment.‍
To show a trail line for the vessel if your radio is tracking
the position of the vessel, select Trail.‍
• To select a color for the trail line, select Trail Line.‍
Deleting a Position-Report Call
1 Select Nav Info > Other Vessels > DSC List.‍
2 Select a position-report call.‍
3 Select Edit > Clear Report.‍
Viewing Vessel Trails on the Chart
You can view trails for all tracked vessels on some chart views.‍
By default, a black line indicates the path of the vessel, a black
dot indicates each previously reported position of a tracked
vessel, and a blue flag indicates the last reported position of the
vessel.‍
1 From a chart or 3D chart view, select Menu > Other Vessels
> DSC Trails.‍
Select
the number of hours to show tracked vessels on the
2
chart.‍
For example, if you select 4 Hours, all trail points that are
less than four hours old appear for all tracked vessels.‍
Individual Routine Calls
When you connect the chartplotter to a Garmin VHF radio over
the NMEA 2000 or the NMEA 0183 network, you can use the
chartplotter interface to set up an individual routine call.‍
When setting up an individual routine call from your chartplotter,
you can select the DSC channel on which you want to
communicate.‍ The radio transmits this request with your call.‍
Selecting a DSC Channel
NOTE: The selection of a DSC channel is limited to those
channels that are available in all frequency bands.‍ The default
channel is 72.‍ If you select a different channel, the chartplotter
uses that channel for subsequent calls until you call using
another channel.‍
1 Select Nav Info > Other Vessels > DSC List.‍
2 Select a vessel or a station to call.‍
3 Select Call with Radio > Channel.‍
21
4 Select an available channel.‍
Making an Individual Routine Call
NOTE: When initiating a call from the chartplotter, if the radio
does not have an MMSI number programmed, the radio will not
receive call information.‍
1 Select Nav Info > Other Vessels > DSC List.‍
2 Select a vessel or a station to call.‍
3 Select Call with Radio.‍
4 If necessary, select Channel, and select a new channel.‍
5 Select Send.‍
The chartplotter sends information about the call to the radio.‍
6 On your Garmin VHF radio, select Call.‍
Making an Individual Routine Call to an AIS Target
1 From a chart or 3D chart view, select an AIS target.‍
2 Select AIS Vessel > Call with Radio.‍
3 If necessary, select Channel, and select a new channel.‍
4 Select Send.‍
The chartplotter sends information about the call to the radio.‍
On
your Garmin VHF radio, select Call.‍
5
Media Player
NOTE: The media player feature is not compatible with all
chartplotter models.‍
If you have a Garmin Meteor™ media player or a stereo
equipped with FUSION-Link™ connected to the NMEA 2000
network, you can control the stereo using the chartplotter.‍ The
chartplotter should automatically detect the media player when
it is first connected.‍
You can play media from sources connected to the media
player and sources connected to the NMEA 2000 network.‍ Your
chartplotter and iPod® can be connected using a Garmin
Meteor.‍
Opening the Media Player
From any screen, select Media.‍
NOTE: The media option appears only when the device is
connected to the chartplotter.‍
Selecting the Media Source
When you have multiple media devices connected on a
network, such as the NMEA 2000 network, you can select the
media source you want to control from your chartplotter.‍
NOTE: You can play media only from sources that are
connected to the device.‍
NOTE: Not all features are available on all media sources.‍
1 From the media screen, select Menu.‍
When you have multiple media devices connected, a device
menu appears.‍
2 Select a device.‍
3 Select Source.‍
NOTE: The source menu appears only for devices that
support multiple media sources.‍
4 Select a source.‍
Connecting a Bluetooth® Wireless Device to the
Meteor Media Player
You can wirelessly connect the media player to a Bluetooth
device.‍
1 Place the Bluetooth device within 33 ft.‍ (10 m) of the media
player.‍
22
2 From the media screen, select BT Devices or Bluetooth
Device.‍
3 Enable the Discoverable mode on the Bluetooth device.‍
A list of devices appears.‍
4 Select the media player from the options on your Bluetooth
device.‍
Browsing for Music
1 From the media screen, select Browse or Menu > Browse.‍
2 Select Select or select an option.‍
Enabling Alphabetical Search
To find a song or album in a large list, you can enable the
alphabetical search feature.‍
From the media screen, select Menu > Installation > Alpha
Search.‍
Setting a Song to Repeat
1 While playing a song, select Menu > Repeat.‍
2 If necessary, select Single.‍
Setting a Song to Repeat
1 While playing a song, select Menu > Repeat.‍
2 If necessary, select Single.‍
Setting All Songs to Repeat
From the media screen, select Menu > Repeat > All.‍
Setting Songs to Shuffle
1 From the media screen, select Menu > Shuffle.‍
2 If necessary, select an option.‍
Listening to the Radio
Saving a Channel as a Preset
You can save up to fifteen AM stations and fifteen FM stations
as presets.‍
1 From the AM, FM, or VHF page, tune the device to a
channel.‍
2 Select Menu > Presets > Add Current Channel.‍
Removing a Channel Preset
1 Tune the device to a channel.‍
2 Select Menu > Presets > Remove Current Channel.‍
Changing the Tuning Mode
You can change how you select a station for some media types,
such as FM or AM radio.‍
NOTE: Not all tuning modes are available for all media sources.‍
1 From the media screen, select Menu > Tuning Mode.‍
2 Select an option.‍
3 If necessary, select Select.‍
Setting the Tuner Region
1 From the media screen, select Menu > Installation > Tuner
Region.‍
2 Select an option.‍
Opening the MTP Source
Before you can open the MTP source, you must connect your
MTP device to the Meteor device.‍
You can access music on your Media Transfer Protocol (MTP)
device, such as an Android™.‍ You can also charge your phone
or media player while it is connected and playing music.‍
1 Connect your MTP source through USB, such as the
FUSION-Link stereo, the external USB plug, or an external
dock.‍
2 Select Menu > Source > MTP.‍
Media Player
Adjusting the VHF Squelch
NOTE: Your media player must support VHF radio to use this
feature.‍
1 From the VHF source page, select Menu > Squelch.‍
2 Use the slider bar to adjust the VHF squelch.‍
• To adjust the color saturation, select Saturation, and
select Up, Down, or Auto.‍
• To adjust the contrast, select Contrast, and select Up,
Down, or Auto.‍
• To allow the chartplotter to automatically select the source
format, select Standard > Auto.‍
Scanning VHF Channels
Before you can scan VHF channels, you must set the source to
VHF.‍
You can monitor VHF channels saved as presets for activity and
automatically switch to an active channel.‍
Select Menu > Start Scanning.‍
Icons
NOTE: Not all devices have these keys.‍
The keys used vary by device.‍
Icon
Description
Saves or deletes a channel as a preset
Repeats all songs
Searches for stations
Searches for stations
Shuffles
Adjusting the Volume
Enabling and Disabling Zones
If you have wired your vessel's speakers into zones, you can
disable unused zones.‍
1 From the media screen, select Menu > Audio Levels >
Enable/Disable Zones.‍
2 Select a zone.‍
.‍
Setting the Device Name
1 From the media screen, select Menu > Installation > Set
Device Name.‍
2 Enter a device name.‍
3 Select Select or Done.‍
Viewing Video
Before you can view video, you must connect a compatible
chartplotter to an analog video source.‍
NOTE: This feature is not available with all models.‍
Select Video.‍
Configuring the Video Appearance
1 Select Video > Menu.‍
2 Select an option:
• To show the video using a stretched aspect ratio, select
Aspect > Stretch.‍ The video cannot be stretched beyond
the dimensions provided by the connected video device,
and it may not fill the entire screen.‍
• To show the video using a standard aspect ratio, select
Aspect > Standard.‍
• To adjust the brightness, select Brightness, and select
Up, Down, or Auto.‍
Viewing Video
WARNING
The weather information provided through this product is
subject to service interruptions and may contain errors,
inaccuracies, or outdated information, and consequently should
not be relied upon exclusively.‍ Always use common sense while
navigating, and check alternate weather information sources
prior to making safety-related decisions.‍ You acknowledge and
agree that you shall be solely responsible for use of the weather
information and all decisions taken with respect to navigating in
weather.‍ Garmin will not be responsible for any consequences
of using SiriusXM weather information.‍
NOTE: SiriusXM data is not available in all regions.‍
A Garmin SiriusXM satellite weather receiver and antenna
receives satellite weather data and shows it on various Garmin
devices, including the Navigation chart on a compatible
chartplotter.‍ The weather data for each feature comes from
reputable weather data centers such as the National Weather
Service and the Hydrometeorological Prediction Center.‍ For
more information, go to www.siriusxm.com/‍sxmmarine.‍
Repeats one song
Muting the Media Volume
1 From the media screen, select
2 If necessary, select Select.‍
SiriusXM®
SiriusXM Equipment and Subscription
Requirements
To use satellite weather, you must have a compatible satellite
weather receiver.‍ To use SiriusXM satellite radio, you must
have a compatible satellite radio receiver.‍ Go to www.garmin.com for more information.‍ You must also have a
valid subscription to receive satellite weather and radio.‍ For
more information, refer to the instructions for your satellite
weather and radio equipment.‍
Weather Data Broadcasts
Weather data is broadcast at five-minute intervals.‍ When the
Garmin receiver is turned on, or when a different weather
feature is selected, the receiver must receive new data before it
can be shown.‍ You might experience a delay before weather
data or a different feature appears on the chart.‍
NOTE: Any weather feature can change in appearance if the
source that provides the information changes.‍
Viewing Precipitation Information
Precipitation ranging from very light rain and snow, up to strong
thunderstorms, is indicated in varying shades and colors.‍
Precipitation is shown either independently or with other
weather information.‍
Select Weather > Precipitation.‍
The time stamp in the upper-left corner of the screen
indicates the elapsed time since the weather data provider
last updated the information.‍
Precipitation Views
From the precipitation weather chart, select Menu.‍
Radar Loop: Shows precipitation information as an image of
the latest update or as an animated loop of the latest
updates.‍ The time stamp indicates the elapsed time since
the service provider generated the weather radar frame
currently displayed on the screen.‍
Cloud Cover: Shows cloud cover data.‍
23
Waypoints: Shows waypoints.‍
Legend: Shows the weather legend.‍
Storm Cell and Lightning Information
Storm cell icons
on the weather Precipitation chart indicate
both the present position of a storm and the projected path of
that storm in the immediate future.‍
Red cones appear with a storm cell icon, and the widest part of
each cone points in the direction of the projected path of the
storm cell.‍ The red lines in each cone indicate where the storm
will most likely be in the near future.‍ Each line represents 15
minutes.‍
Lightning strikes are represented by .‍ Lightning appears on
the weather Precipitation chart if strikes were detected within
the last seven minutes.‍ The ground-based lightning detection
network detects cloud-to-ground lightning only.‍
Hurricane Information
The weather Precipitation chart can show the present position
of a hurricane , a tropical storm, or a tropical depression.‍ A
red line stemming from a hurricane icon indicates the projected
path of the hurricane.‍ Darkened dots on the red line indicate the
projected locations through which the hurricane will pass, as
received from the weather data provider.‍
Weather Warnings and Weather Bulletins
When a marine weather warning, weather watch, weather
advisory, weather bulletin, or other weather statement is issued,
shading indicates the area to which the information applies.‍ The
aqua lines on the chart indicate the boundaries of marine
forecasts, coastal forecasts, and offshore forecasts.‍ Weather
bulletins may consist of either weather watches or weather
advisories.‍
To view information about the warning or bulletin, select the
shaded area.‍
Color
Marine Weather Weather Subcategories
Group
Light Blue Flash Flood
Dark Blue Flood
Yellow
Pink
Marine/Wind
Miscellaneous
Orange
Severe Storm
Red
Tornado
Purple
Tropical
Areal Flood, Coastal Flood, Debris Flow,
Flood, High Water Level, Hydrological,
Lakeshore Flood, Storm Surge
Brisk Wind, Extreme Wind, Freezing
Spray, Gale, Hazardous Seas, High Surf,
High Wind, Hurricane Force Wind, Lake
Wind, Les Suêtes Wind, Low Water,
Marine Weather, Rip Tide, Small Craft,
Small Craft Hazardous Seas, Small Craft
Rough Bar, Small Craft Winds, Special
Marine, Squall, Storm, Strong Wind,
Tsunami, Waterspout, Wind,
Wreckhouse Winds
Air Quality, Air Stagnation, Ashfall,
Blowing Dust, Excessive Heat, Fire
Weather, Heat, High Heat and Humidity,
Humidex, Humidex and Health, Rainfall,
Special Weather, Weather
Hurricane, Inland Hurricane, Inland
Tropical Storm, Tropical Storm, Typhoon
Color
Marine Weather Weather Subcategories
Group
Dark
Gray
Visibility
Dense Fog, Dense Smoke, Dust Storm,
Smog
White
Winter
Arctic Outflow, Avalanche, Blizzard,
Blowing Snow, Cold Wave, Extreme
Cold, Flash Freeze, Freeze, Freezing
Drizzle, Freezing Fog, Freezing Rain,
Frost, Hard Freeze, Heavy Freezing
Spray, Heavy Snow, Ice Storm, Lake
Effect Blowing Snow, Lake Effect Snow,
Sleet, Snow, Snow and Blowing Snow,
Snow Squall, Snowfall, Wind Chill,
Winter Storm, Winter Weather
Forecast Information
The Forecast chart shows city forecasts, marine forecasts,
warnings, hurricane warnings, METARS, county warnings,
weather fronts and pressure centers, surface pressure, and
weather buoys.‍
Viewing Forecast Information for Another Time
Period
1 Select Weather > Forecast.‍
2 Select an option:
• To view the weather forecast for the next 12 hours, select
Next Forecast or , and to view forecasts up to 48 hours,
in 12-hour increments, select Next Forecast or again.‍
• To view the weather forecast for the previous 12 hours,
select Previous Forecast or , and to view previous
forecasts, up to 48 hours ago, in 12-hour increments,
select Previous Forecast or again.‍
Viewing a Marine Forecast or an Offshore Forecast
1 Select Weather > Forecast.‍
2 Pan the chart to an offshore location.‍
The Marine Forecast or Offshore Forecast options appear
when forecast information is available.‍
3 Select Marine Forecast or Offshore Forecast.‍
Weather Fronts and Pressure Centers
Weather fronts appear as lines that indicate the leading edge of
an air mass.‍
Front Symbol
Description
Cold front
Warm front
Stationary front
Occluded front
Trough
Pressure-center symbols often appear near weather fronts.‍
PressureCenter
Symbol
Description
Indicates a low-pressure center, which is a region of
relatively lower pressure.‍ Moving away from a lowpressure center results in increased pressure.‍ Winds
flow counterclockwise around low-pressure centers in
the northern hemisphere.‍
Indicates a high-pressure center, which is a region of
relatively higher pressure.‍ Moving away from a highpressure center results in decreased pressure.‍ Winds
flow clockwise around high-pressure centers in the
northern hemisphere.‍
City Forecasts
City forecasts appear as weather symbols.‍ The forecast is
viewed in 12-hour increments.‍
24
SiriusXM®
Symbol Weather
Symbol Weather
Partly cloudy
Fair (sunny, hot, clear)
Cloudy
Rain (drizzle, sleet, showers)
Windy
Foggy
Thunderstorms
Snow (snow showers, flurries,
blizzard, blowing snow, sleet,
freezing rain, freezing drizzle)
Smoke (dusty, hazy)
Viewing Sea Conditions
The Sea Conditions chart shows information about surface
conditions, including winds, wave height, wave period, and
wave direction.‍
Select Weather > Sea Conditions.‍
Surface Winds
Surface wind vectors appear on the Sea Conditions chart using
wind barbs that indicate the direction from which the wind is
blowing.‍ A wind barb is a circle with a tail.‍ The line or flag
attached to the tail of the wind barb indicates the wind speed.‍ A
short line represents 5 knots, a long line represents 10 knots,
and triangle represents 50 knots.‍
Wind Barb
Wind Speed
Wind Barb
Wind Speed
Calm
20 knots
5 knots
50 knots
10 knots
65 knots
15 knots
Wave Height, Wave Period, and Wave Direction
Wave heights for an area appear as variations in color.‍ Different
colors indicate different wave heights, as shown in the legend.‍
The wave period indicates the time (in seconds) between
successive waves.‍ Wave period lines indicate areas that have
the same wave period.‍
Wave directions appear on the chart using red arrows.‍ The
direction of each arrow pointer indicates the direction in which a
wave is moving.‍
Viewing Forecast Sea Conditions Information for
Another Time Period
1 Select Weather > Sea Conditions.‍
2 Select an option:
• To view forecasted sea conditions for the next 12 hours,
select Next Forecast or , and to view forecasts up to 48
hours, in 12-hour increments, select Next Forecast or
again.‍
• To view the forecasted sea conditions for the previous 12
hours, select Previous Forecast or , and to view
previous forecasts, up to 48 hours ago, in 12-hour
increments, select Previous Forecast or again.‍
Viewing Fishing Information
The weather Fishing chart shows present water temperature,
present surface pressure conditions, and fishing forecasts.‍
Select Weather > Fishing.‍
Surface Pressure and Water Temperature Data
Surface-pressure information appears as pressure isobars and
pressure centers.‍ Isobars connect points of equal pressure.‍
Pressure readings can help to determine weather and wind
conditions.‍ High-pressure areas are generally associated with
fair weather.‍ Low-pressure areas are generally associated with
clouds and the chance of precipitation.‍ Isobars packed closely
SiriusXM®
together show a strong pressure gradient.‍ Strong pressure
gradients are associated with areas of stronger winds.‍
Pressure units are shown in millibars (mb), inches of Mercury
(inHg), or hectopascals (hPa).‍
Colored shading indicates the surface temperature of the water,
as shown in the legend in the corner of the display.‍
Forecasting Fish Locations
You can show areas that contain optimal weather conditions for
specific species of fish.‍
1 From the weather Fishing chart, select Weather > Fishing >
Menu > Fish Species.‍
2 Select a species of fish.‍
3 Select On.‍
4 Repeat steps 2 and 3 to show areas with optimal weather
conditions for additional species of fish.‍
Shaded areas indicate optimal fishing areas.‍ If you have
selected more than one species of fish, you can select a
shaded area to view the fish species that are included in the
shaded area.‍
Changing the Sea Surface Temperature Color Range
You can change the color range dynamically to view higher
resolution sea surface temperature readings.‍
1 From the weather Fishing chart, select Menu > Sea
Temperature.‍
2 Select an option:
• To allow the chartplotter to adjust the temperature range
automatically, select Scale > Auto.‍
The chartplotter automatically finds the lower and upper
limits for the current screen, and updates the
temperature-color scale.‍ These limits remain until you
close the chart or update the scale.‍
• To enter the lower and upper limits for the temperature
range, select Scale > Manual, and enter the lower and
upper limits.‍
Visibility Information
Visibility is the forecast maximum horizontal distance that can
be seen at the surface, as shown in the legend on the left of the
screen.‍ Variations in the visibility shading show the forecast
change in surface visibility.‍
Select Weather > Visibility.‍
Viewing Forecast Visibility Information for Another
Time Period
1 Select Weather > Visibility.‍
2 Select an option:
• To view the visibility forecast for the next 12 hours, select
Next Forecast or , and to view forecasts up to 48 hours,
in 12-hour increments, select Next Forecast or again.‍
• To view the visibility forecast for the previous 12 hours,
select Previous Forecast or , and to view previous
forecasts, up to 48 hours ago, in 12-hour increments,
select Previous Forecast or again.‍
Viewing Buoy Reports
Report readings are taken from buoys and coastal observation
stations.‍ These readings are used to determine air temperature,
dew point, water temperature, tide, wave height and period,
wind direction and speed, visibility, and barometric pressure.‍
1 From a weather chart, select .‍
2 Select Review > Buoy.‍
25
Review does not appear if the cursor is not near an object.‍ If
the cursor is near only one object, the name of the buoy
appears.‍
Viewing Local Weather Information near a Buoy
You can select an area near a buoy to view forecast
information.‍
1 From a weather chart, select a location on the chart.‍
2 Select Local Weather.‍
3 Select an option:
• To view present weather conditions from a local weather
service, select Current Conditions.‍
• To view a local weather forecast, select Forecast.‍
• To view surface wind and barometric pressure
information, select Sea Surface.‍
• To view wind and wave information, select Marine
Bulletin.‍
Creating a Waypoint on a Weather Chart
1 From a weather chart, select a location.‍
2 Select New Waypoint.‍
Weather Overlay
The weather overlay superimposes weather and weatherrelated information on the Navigation chart, the Fishing chart,
and the Perspective 3D chart view.‍ The Navigation chart and
the Fishing chart can show weather radar, height of cloud tops,
lightning, weather buoys, county warnings, and hurricane
warnings.‍ The Perspective 3D chart view can show weather
radar.‍
Weather overlay settings configured for use on one chart are
not applied to another chart.‍ The weather overlay settings for
each chart must be configured separately.‍
NOTE: The offshore Fishing chart is available with premium
charts, in some areas.‍
Turning On the Weather Overlay on a Chart
From the Navigation chart or Fishing chart, select Menu >
Chart Setup > Weather > Weather > On.‍
Weather Overlay Settings on the Navigation Chart
From the Navigation chart, select Menu > Chart Setup >
Weather.‍
Weather: Turns on and off the weather overlay.‍
Precipitation: Shows precipitation data.‍
Cloud Cover: Shows cloud cover data.‍
Satellite IR: Shows infrared satellite data, which displays clouds
based on cloud-top temperatures.‍ Deeper shades of gray
represent colder clouds often found with cirrus or
thunderstorm clouds.‍ Lighter shades or a lack of shading
indicate warmer clouds usually associated with stratus or
fog.‍
Buoys: Shows weather buoys.‍
Legend: Shows the weather legend.‍
Weather Overlay Settings on the Fishing Chart
From the Fishing chart, select Menu > Chart Setup > Weather.‍
Precipitation: Shows precipitation radar.‍
Sea Temperature: Shows sea temperature data.‍
Buoys: Shows weather buoys.‍
Legend: Shows the weather legend.‍
Viewing Weather Subscription Information
You can view information about the weather services you have
subscribed to and how many minutes have passed since the
data for each service was updated.‍
Select Weather > Weather Subscription.‍
SiriusXM Radio
When you have a Garmin SiriusXM receiver connected to the
chartplotter, you may have access to SiriusXM satellite radio,
depending on your subscription.‍
Customizing the Channel Guide
SiriusXM radio channels are grouped in categories.‍ You can
select the category of channels that appear in the channel
guide.‍
1 Select Media > Menu > Category.‍
2 Select a category.‍
Saving a SiriusXM Channel to the Presets List
You can save your favorite channels to the presets list.‍
1 Select Media.‍
2 Select the channel you want to save as a preset.‍
3 Select Menu > Presets > Add Current Channel.‍
Adjusting SiriusXM Satellite Radio Volume
1 Select Media > Menu.‍
2 Select or .‍
Device Configuration
Turning On the Chartplotter Automatically
You can set the chartplotter to turn on automatically when the
power is applied.‍ Otherwise, you must turn on the chartplotter
by pressing .‍
Select Settings > System > Auto Power.‍
NOTE: When Auto Power is On, and the chartplotter is
turned off using , and power is removed and reapplied
within less than two minutes, you may need to press to
restart the chartplotter.‍
System Settings
Select Settings > System.‍
Display: Adjusts the backlight brightness and color scheme.‍
Beeper: Turns on and off the tone that sounds for alarms and
selections.‍
GPS: Provides information about the GPS satellite settings and
fix.‍
Auto Power: Turns on the device automatically when power is
applied (Turning On the Chartplotter Automatically).‍
Language: Sets the on-screen text language.‍
Speed Sources: Sets the source of the speed data used to
calculate true wind speed or fuel economy.‍ Water speed is
the speed reading from a water-speed sensor, and GPS
speed is calculated from your GPS position.‍
System Information: Provides information about the device
and the software version.‍
Simulator: Turns on the simulator and allows you to set the
speed and simulated location.‍
GPS Settings
Select Settings > System > GPS.‍
Skyview: Shows the relative position of GPS satellites in the
sky.‍
26
Device Configuration
GLONASS: Turns on or off GLONASS usage (Russia satellite
system).‍ When the system is used in situations with poor sky
visibility, this configuration can be used in combination with
GPS to provide more accurate position information.‍
WAAS/EGNOS: Turns on or off WAAS (in North America) or
EGNOS (in Europe), which can provide more-accurate GPS
position information.‍ When using WAAS or EGNOS, the
device may take longer to acquire satellites.‍
Speed Filter: Averages the speed of your vessel over a short
period of time for smoother speed values.‍
Viewing the Event Log
enter a negative number to compensate for a large vessel that
may draw several feet of water.‍
1 Complete an action, based on the location of the transducer:
• If the transducer is installed at the water line À, measure
the distance from the transducer location to the keel of the
boat.‍ Enter this value in steps 3 and 4 as a positive
number.‍
• If the transducer is installed at the bottom of the keel Á,
measure the distance from the transducer to the water
line.‍ Enter this value in steps 3 and 4 as a negative
number.‍
The event log shows a list of system events.‍
Select Settings > System > System Information > Event
Log.‍
Viewing System Software Information
You can view the software version, the basemap version, any
supplemental map information (if applicable), the software
version for an optional Garmin radar (if applicable), and the unit
ID number.‍ You may need this information to update the system
software or to purchase additional map data information.‍
Select Settings > System > System Information >
Software Information.‍
My Vessel Settings
NOTE: Some settings and options require additional charts or
hardware.‍
Select Settings > My Vessel.‍
Keel Offset: Offsets the surface reading for the depth of a keel,
making it possible to measure depth from the bottom of the
keel instead of from the transducer location (Setting the Keel
Offset).‍
Temp.‍ Offset: Compensates for the water temperature reading
from a NMEA 0183 water-temperature sensor or a
temperature-capable transducer (Setting the Water
Temperature Offset).‍
Calibrate Water Speed: Calibrates the speed-sensing
transducer or sensor (Calibrating a Water Speed Device).‍
Fuel Capacity: Sets the combined fuel capacity of all the fuel
tanks on your vessel (Setting the Fuel Capacity of the
Vessel).‍
Vessel Type: Enables some chartplotter features based on the
boat type.‍
Fill Up All Tanks: Sets the tank levels to full (Synchronizing the
Fuel Data with the Actual Vessel Fuel).‍
Add Fuel to Boat: Allows you to enter the quantity of fuel you
added to your tank, when you did not entirely fill up the tank
(Synchronizing the Fuel Data with the Actual Vessel Fuel).‍
Set Total Fuel Onboard: Sets the combined amount of fuel in
all the fuel tanks on your vessel (Synchronizing the Fuel
Data with the Actual Vessel Fuel).‍
Set Gauge Limits: Sets the upper and lower limits of various
gauges (Customizing Engine Gauge and Fuel Gauge Limits).‍
Setting the Vessel Type
You can select your boat type to configure the chartplotter
settings and to use features customized for your boat type.‍
1 Select Settings > My Vessel > Vessel Type.‍
2 Select Powerboat or Sailboat.‍
Setting the Keel Offset
You can enter a keel offset to compensate the surface reading
for the depth of a keel, making it possible to measure depth
from the bottom of the keel instead of from the transducer
location.‍ Enter a positive number to offset for a keel.‍ You can
Device Configuration
2 Select Settings > My Vessel > Keel Offset.‍
3 Select or based on the location of the transducer.‍
4 Enter the distance measured in step 1.‍
Calibrating a Water Speed Device
If you have a speed-sensing transducer connected to the
chartplotter, you can calibrate that speed-sensing device to
improve the accuracy of water-speed data displayed by the
chartplotter.‍
1 Select Settings > My Vessel > Calibrate Water Speed.‍
2 Follow the on-screen instructions.‍
If the boat is not moving fast enough or the speed sensor is
not registering a speed, a message appears.‍
3 Select OK, and safely increase the boat speed.‍
4 If the message appears again, stop the boat, and ensure the
speed-sensor wheel is not stuck.‍
5 If the wheel turns freely, check the cable connections.‍
6 If you continue to get the message, contact Garmin product
support.‍
Setting the Water Temperature Offset
Before you can set the water temperature offset, you must have
a NMEA 0183 water-temperature sensor or a temperaturecapable transducer to measure water temperature.‍
The temperature offset compensates for the temperature
reading from a temperature sensor.‍
1 Measure the water temperature using the temperature
sensor or temperature-capable transducer that is connected
to the chartplotter.‍
2 Measure the water temperature using a different temperature
sensor or a thermometer that is known to be accurate.‍
3 Subtract the water temperature measured in step 1 from the
water temperature measured in step 2.‍
This is the temperature offset.‍ Enter this value in step 5 as a
positive number if the sensor connected to the chartplotter
27
measures the water temperature as being colder than it
actually is.‍ Enter this value in step 5 as a negative number if
the sensor connected to the chartplotter measures the water
temperature as being warmer than it actually is.‍
4 Select Settings > My Vessel > Temp.‍ Offset.‍
5 Enter the temperature offset calculated in step 3.‍
Communications Settings
NOTE: Some settings and options require additional charts or
hardware.‍
Select Settings > Communications.‍
Serial Port 1: Sets the input/output format for port 1 to use
when connecting the chartplotter to external NMEA devices,
computers, or other Garmin devices.‍
Serial Port 2: Sets the input/output format for port 2 to use
when connecting the chartplotter to external NMEA devices,
computers, or other Garmin devices.‍
NMEA 0183 Setup: Sets the NMEA 0183 sentences the
chartplotter transmits, how many digits to the right of the
decimal point are transmitted in a NMEA output, and how
waypoints are identified (NMEA 0183 Settings).‍
NMEA 2000 Setup: Allows you to view and label the devices on
the NMEA 2000 network ( NMEA 2000 Settings).‍
Marine Network: Allows you to view the devices with which you
are sharing maps, sonar, or radar.‍ Not available on all
chartplotter models.‍
NOTE: You can only view networked data on a model that
supports that data.‍ For example, you cannot view networked
radar on an echoMAP 70 model, because that model does
not support radar.‍
Wireless Devices: Allows you set up wireless devices
(Communication with Wireless Devices ).‍ Not available on all
chartplotter models.‍
Wi-Fi® Network: Allows you set up the Wi-Fi® network
Communication with Wireless Devices ).‍
NMEA 2000 and NMEA 0183
GPSMAP 500 series and GPSMAP 700 series chartplotters can
accept data from both NMEA 0183 devices and certain NMEA
2000 devices connected to an existing NMEA 2000 network on
your boat.‍
echoMAP 50 series and echoMAP 70 series chartplotters can
accept data from NMEA 0183 compliant devices.‍
NMEA 0183
The chartplotters support the NMEA 0183 standard, which is
used to connect various NMEA 0183 devices, such as VHF
radios, NMEA instruments, autopilots, wind sensors, and
heading sensors.‍
To connect the chartplotter to optional NMEA 0183 devices, see
the chartplotter installation instructions.‍
The approved NMEA 0183 sentences for the chartplotter are
GPAPB, GPBOD, GPBWC, GPGGA, GPGLL, GPGSA,
GPGSV, GPRMB, GPRMC, GPRTE, GPVTG, GPWPL,
GPXTE, and Garmin proprietary sentences PGRME, PGRMM,
and PGRMZ.‍
This chartplotter also includes support for the WPL sentence,
DSC, and sonar NMEA 0183 input with support for the DPT
(depth) or DBT, MTW (water temperature), and VHW (water
temperature, speed, and heading) sentences.‍
NMEA 0183 Settings
Select Settings > Communications > NMEA 0183 Setup.‍
Sounder: Enables NMEA 0183 output sentences for the
sounder (if applicable).‍
Route: Enables NMEA 0183 output sentences for routes.‍
28
System: Enables NMEA 0183 output sentences for system
information.‍
Garmin: Enables NMEA 0183 output sentences for Garmin
proprietary sentences.‍
Posn Precision: Adjusts the number of digits to the right of the
decimal point for transmission of NMEA output.‍
Waypoint IDs: Sets the device to transmit waypoint names or
numbers via NMEA 0183 while navigating.‍ Using numbers
may resolve compatibility issues with older NMEA 0183
autopilots.‍
Diagnostics: Displays NMEA 0183 diagnostic information.‍
Defaults: Restores the NMEA 0183 settings to the original
factory defaults.‍
NMEA 2000 Settings
Select Settings > Communications > NMEA 2000 Setup.‍
Device List: Displays the devices connected to the network.‍
Label Devices: Changes the labels for available connected
devices.‍
Communication with Wireless Devices
The chartplotters can create a wireless network to which you
can connect wireless devices.‍ Also, some models can connect
to Bluetooth wireless devices using the AVRCP profile.‍
Setting Up the Wireless Network
The chartplotters can create a Wi-Fi network to which you can
connect wireless devices.‍ The first time you access the wireless
network settings, you are prompted to set up the network.‍
1 Select Settings > Communications.‍
2 If necessary, select Wireless Devices.‍
3 Select Wi-Fi® Network > Wi-Fi® Connection > On > OK
4 If necessary, enter a name for this wireless network.‍
5 Enter a password.‍
You will need this password to access the wireless network
from a wireless device.‍ The password is case-sensitive.‍
Connecting a Wireless Device to the Chartplotter
Before you can connect a wireless device to the chartplotter
wireless network, you must configure the chartplotter wireless
network (Setting Up the Wireless Network).‍
You can connect up to five wireless devices to the chartplotter
to share data.‍ For example, you can connect an iOS® device to
the chartplotter to share BlueChart Mobile data.‍
1 From the iOS device, select Settings > Wi-Fi.‍
2 Select the wireless network name you entered for the
chartplotter network (Setting Up the Wireless Network).‍
3 Enter the password you entered when you set up the
chartplotter as a wireless network.‍
Changing the Wireless Channel
You can change the wireless channel if you have trouble finding
or connecting to a device, or if you experience interference.‍
1 Select Settings > Communications > Wireless Devices >
Advanced > Wi-Fi® Channel.‍
2 Enter a new channel.‍
You do not need to change the wireless channel in any devices
connected to this network.‍
Connecting a Bluetooth Wireless Device
NOTE: Bluetooth technology is not available on all chartplotter
models.‍
You can wirelessly connect the chartplotter to a Bluetooth
device.‍
1 Place the Bluetooth device within 33 ft.‍ (10 m) of the
chartplotter.‍
Device Configuration
2 Select Settings > Communications > Wireless Devices >
Bluetooth Devices > Bluetooth.‍
3 If necessary, enter a name for this wireless network.‍
4 If necessary, enter a password.‍
You will need this password to access the wireless network
from a wireless device.‍ The password is case-sensitive.‍
Disconnecting a Bluetooth Wireless Device
1 Select Settings > Communications > Wireless Devices >
Bluetooth Devices > Device List.‍
2 Select a device.‍
3 Select Forget Device.‍
Setting Alarms
Navigation Alarms
Select Settings > Alarms > Navigation.‍
Arrival: Sets an alarm to sound when you are within a specified
distance or time from a turn or a destination.‍
Anchor Drag: Sets an alarm to sound when you exceed a
specified drift distance while anchored.‍
Off Course: Sets an alarm to sound when you are off course by
a specified distance.‍
System Alarms
Alarm Clock: Sets an alarm clock.‍
Device Voltage: Sets an alarm to sound when the battery
reaches a specified low voltage.‍
GPS Accuracy: Sets an alarm to sound when the GPS location
accuracy falls outside the user-defined value.‍
Setting the Fuel Alarm
Before you can set a fuel level alarm, a compatible fuel flow
sensor must be connected to the NMEA 2000 network.‍
You can set an alarm to sound when the total amount of
remaining onboard fuel reaches the level you specify.‍
1 Select Settings > Alarms > Fuel > Fuel Alarm > On.‍
2 Enter the remaining amount of fuel that triggers the alarm.‍
Setting Weather Alarms
Before you can set weather alarms, you must have a
compatible chartplotter connected to a weather device, such as
a GXM™ device, and have a valid weather subscription.‍
1 Select Settings > Alarms > Weather.‍
2 Turn on alarms for specific weather events.‍
Units Settings
Select Settings > Units.‍
System Units: Sets the unit format for the device.‍
Heading: Sets the direction references used in calculating
heading information.‍ Auto Mag Var (automatic magnetic
variation) sets the magnetic declination for your location
automatically.‍ True sets true north as the heading reference.‍
Grid sets grid north as the heading reference (000º).‍ User
Mag Var allows you to enter the magnetic variation value
manually.‍
Position Format: Sets the position format in which a given
location reading appears.‍ Do not change this setting unless
you are using a map or chart that specifies a different
position format.‍
Map Datum: Sets the coordinate system on which the map is
structured.‍ Do not change this setting unless you are using a
map or chart that specifies a different map datum.‍
Pressure Ref.‍ Time: Sets the reference time used to calculate
the barometer trend.‍ The trend is indicated in the barometer
field.‍
Device Configuration
Time Format: Sets a 12-hour, 24-hour, or UTC time format.‍
Time Zone: Sets the time zone, or allows automatic selection
based on GPS location.‍
Navigation Settings
NOTE: Some settings and options require additional charts or
hardware.‍
Select Settings > Navigation.‍
Route Labels: Sets the type of labels shown with route turns on
the map.‍
Auto Guidance: Sets the measurements for the Safe Depth,
Safe Height, and Shoreline Distance, when you are using
some premium maps.‍
Turn Transition Activ.‍: Sets the turn transition to be calculated
based on time or distance.‍
Turn Transition Time: Sets how many minutes before the turn
that you transition to it as the next leg, when Time is
selected for the Turn Transition Activ.‍.‍ You can raise this
value to help improve the accuracy of the autopilot when
navigating a route or an Auto Guidance line with many
frequent turns or at higher speeds.‍ For straighter routes or
slower speeds, lowering this value can improve autopilot
accuracy.‍
Turn Transition Dist.‍: Sets how far before the turn that you
transition to it as the next leg, when Distance is selected for
the Turn Transition Activ.‍.‍ You can raise this value to help
improve the accuracy of the autopilot when navigating a
route or an Auto Guidance line with many frequent turns or at
higher speeds.‍ For straighter routes or slower speeds,
lowering this value can improve autopilot accuracy.‍
Route Start: Selects a starting point for route navigation.‍
Auto Guidance Line Configurations
CAUTION
The Safe Depth and Safe Height settings influence how the
chartplotter calculates an Auto Guidance line.‍ If an area has an
unknown water depth or an unknown obstacle height, the Auto
Guidance line is not calculated in that area.‍ If an area at the
beginning or the end of an Auto Guidance line is shallower than
the safe water depth or lower than the safe obstacle height, the
Auto Guidance line is not calculated in that area.‍ On the chart,
the course through those areas appears as a gray line.‍ When
your boat enters one of those areas, a warning message
appears.‍
NOTE: Auto Guidance is available with premium charts, in
some areas.‍
You can set the parameters the chartplotter uses when
calculating an Auto Guidance line.‍
Safe Depth: Sets the minimum depth (chart depth datum) the
chartplotter uses when calculating an Auto Guidance line.‍
NOTE: The minimum safe depth for the premium charts is 3
feet.‍ If you enter a Safe Depth value of less than 3 feet, the
charts only use depths of 3 feet for Auto Guidance route
calculations.‍
Safe Height: Sets the minimum height (chart height datum) of a
bridge that your boat can safely travel under.‍
Shoreline Distance: Sets how close to the shore you want the
Auto Guidance line to be placed.‍ The Auto Guidance line
may move if you change this setting while navigating.‍ The
available values for this setting are relative, not absolute.‍ To
ensure that the Auto Guidance line is placed the appropriate
distance from shore, you can assess the placement of the
Auto Guidance line using one or more familiar destinations
that require navigation through a narrow waterway (Adjusting
the Distance from Shore).‍
29
Adjusting the Distance from Shore
CAUTION
The Auto Guidance feature is based on electronic chart
information.‍ That data does not ensure obstacle and bottom
clearance.‍ Carefully compare the course to all visual sightings,
and avoid any land, shallow water, or other obstacles that may
be in your path.‍
NOTE: Auto Guidance is available with premium charts, in
some areas.‍
The Shoreline Distance setting indicates how close to the shore
you want the Auto Guidance line to be placed.‍ The Auto
Guidance line may move if you change this setting while
navigating.‍ The available values for the Shoreline Distance
setting are relative, not absolute.‍ To ensure the Auto Guidance
line is placed the appropriate distance from shore, you can
assess the placement of the Auto Guidance line using one or
more familiar destinations that require navigation through a
narrow waterway.‍
1 Dock your vessel or drop the anchor.‍
2 Select Settings > Navigation > Auto Guidance >
Shoreline Distance > Normal.‍
3 Select a destination that you have navigated to previously.‍
4 Select Navigate To > Guide To.‍
5 Review the placement of the Auto Guidance line, and
determine whether the line safely avoids known obstacles
and the turns enable efficient travel.‍
6 Select an option:
• If the placement of the Auto Guidance line is satisfactory,
select Menu > Stop Navigation, and proceed to step 10.‍
• If the Auto Guidance line is too close to known obstacles,
select Settings > Navigation > Auto Guidance >
Shoreline Distance > Far.‍
• If the turns in the Auto Guidance line are too wide, select
Settings > Navigation > Auto Guidance > Shoreline
Distance > Near.‍
7 If you selected Near or Far in step 6, review the placement
of the Auto Guidance line, and determine whether the line
safely avoids known obstacles and the turns enable efficient
travel.‍
Auto Guidance maintains a wide clearance from obstacles in
open water, even if you set the Shoreline Distance setting to
Near or Nearest.‍ As a result, the chartplotter may not
reposition the Auto Guidance line, unless the destination
selected requires navigation through a narrow waterway.‍
8 Select an option:
• If the placement of the Auto Guidance line is satisfactory,
select Menu > Stop Navigation, and proceed to step 10.‍
• If the Auto Guidance line is too close to known obstacles,
select Settings > Navigation > Auto Guidance >
Shoreline Distance > Farthest.‍
• If the turns in the Auto Guidance line are too wide, select
Settings > Navigation > Auto Guidance > Shoreline
Distance > Nearest.‍
9 If you selected Nearest or Farthest in step 8, review the
placement of the Auto Guidance line, and determine whether
the line safely avoids known obstacles and the turns enable
efficient travel.‍
Auto Guidance maintains a wide clearance from obstacles in
open water, even if you set the Shoreline Distance setting to
Near or Nearest.‍ As a result, the chartplotter may not
reposition the Auto Guidance line, unless the destination
selected requires navigation through a narrow waterway.‍
10 Repeat steps 3 through 9 at least once more, using a
different destination each time, until you are familiar with the
functionality of the Shoreline Distance setting.‍
Other Vessel Settings
When your compatible chartplotter is connected to an AIS
device or VHF radio, you can set up how other vessels are
displayed on the chartplotter.‍
Select Settings > Other Vessels.‍
AIS: Enables and disables AIS signal reception.‍
DSC: Enables and disables digital selective calling (DSC).‍
AIS Alarm: Sets the collision alarm (Setting the Safe-Zone
Collision Alarm and Enabling AIS Transmission Test Alerts).‍
Viewing System Software Information
You can view the software version, the basemap version, any
supplemental map information (if applicable), the software
version for an optional Garmin radar (if applicable), and the unit
ID number.‍ You may need this information to update the system
software or to purchase additional map data information.‍
Select Settings > System > System Information >
Software Information.‍
Restoring the Original Chartplotter Factory
Settings
NOTE: This will delete all settings information you have
entered.‍
Select Settings > System > System Information > Factory
Settings.‍
Chartplotter Data Management
Copying Waypoints, Routes, and Tracks to a
Chartplotter
Before you can copy data to the chartplotter, you must have the
latest version of MapSource® or HomePort™ software
programs loaded on your computer and a memory card installed
in the chartplotter.‍
Select an option:
• Copy the data from HomePort to the prepared memory
card.‍
For more information, see the HomePort help file.‍
• Copy the data from MapSource to the prepared memory
card.‍
For more information, see the MapSource help file.‍
Copying Data from a Memory Card
1
2
3
4
Insert a memory card into a card slot.‍
Select Nav Info > Manage Data > Data Transfer > Card.‍
If necessary, select the memory card to copy data to.‍
Select an option:
• To transfer data from the memory card to the chartplotter
and combine it with existing user data, select Merge from
Card.‍
• To transfer data from the memory card to the chartplotter
and overwrite existing user data, select Replace from
Card.‍
5 Select the file name.‍
Copying Waypoints, Routes, and Tracks to a
Memory Card
1 Insert a memory card into the card slot.‍
30
Chartplotter Data Management
2 Select Nav Info > Manage Data > Data Transfer > Card >
Save to Card.‍
3 If necessary, select the memory card to copy data to.‍
4 Select an option:
• To create a new file, select Add New File, and enter a
name.‍ The file name is saved with an .‍adm extension.‍
• To add the information to an existing file, select the file
from the list.‍
Copying Waypoints, Routes, and Tracks to
or from all Chartplotters on the Network
You can transfer information for waypoints, routes, and tracks
from one chartplotter connected to the Garmin Marine Network
to every other chartplotter connected to the network.‍ The
transfer may take a long time, depending on the number of
waypoints being transferred.‍
1 Select Nav Info > Manage Data > Data Transfer >
Network.‍
2 Select an option:
• To transfer data from the chartplotter to the other
chartplotters connected to the network, select Clone User
Data.‍ Existing data is overwritten on those chartplotters.‍
• To transfer data between all the chartplotters connected
to the network, select Merge User Data.‍ Unique data is
combined with existing data on every chartplotter.‍
Copying Built-In Maps to a Memory Card
You can copy maps from the chartplotter to a memory card for
use with HomePort.‍
1 Insert a memory card into the card slot.‍
2 Select Nav Info > Manage Data > Data Transfer > Card.‍
3 To copy the maps loaded onto your chartplotter to the
memory card, select Copy Built-In Map.‍
Backing Up Data to a Computer
1 Insert a memory card into the card slot.‍
2 Select Nav Info > Manage Data > Data Transfer > Card >
Save to Card.‍
3 Select a file name from the list, or select Add New File.‍
4 Select Save to Card.‍
The file name saves with a .‍adm extension.‍
5 Remove the memory card and insert it into a card reader
attached to a computer.‍
6 Open the Garmin\UserData folder on the memory card.‍
7 Copy the backup file on the card and paste it to any location
on the computer.‍
Restoring Backup Data to a Chartplotter
1 Insert a memory card into a card reader that is attached to
the computer.‍
2 Copy a backup file from the computer to the memory card,
into a folder named Garmin\UserData.‍
3 Insert a memory card into the card slot.‍
4 Select Nav Info > Manage Data > Data Transfer > Card >
Replace from Card.‍
Saving System Information to a Memory
Card
You can save system information to a memory card as a
troubleshooting tool.‍ A product support representative may ask
you to use this information to retrieve data about the network.‍
1 Insert a memory card into the card slot.‍
Appendix
2 Select Settings > System > System Information > Garmin
Devices > Save to Card.‍
3 If necessary, select the memory card to save system
information to.‍
4 Remove the memory card.‍
Appendix
Registering Your Device
Help us better support you by completing our online registration
today.‍
• Go to http:​/‍​/‍my​.garmin​.com.‍
• Keep the original sales receipt, or a photocopy, in a safe
place.‍
Calibrating the Touchscreen
You can calibrate the screen if the screen is not properly
responding to the touches.‍ The chartplotter touchscreen does
not normally require calibration.‍
1 Select Settings > System > Display > Calibrate
Touchscreen.‍
2 Follow the on-screen instructions.‍
Loading the New Software on a Memory
Card
The device may contain a software-update memory card.‍ If so,
follow the instructions provided with the card.‍ If a software
update memory card is not included, you must copy the
software update to a memory card.‍
1 Insert a memory card into the card slot on the computer.‍
2 Go to www.garmin.com/‍support​/‍software​/‍marine​.html.‍
3 Select Download next to “Garmin Marine Network with SD
card.‍”
4 Read and agree to the terms.‍
5 Select Download.‍
6 Select Run.‍
7 Select the drive associated with the memory card, and select
Next > Finish.‍
Updating the Device Software
Before you can update the software, you must obtain a
software-update memory card or load the latest software onto a
memory card.‍
1 Turn on the chartplotter.‍
2 After the home screen appears, insert the memory card into
the card slot.‍
NOTE: In order for the software update instructions to
appear, the device must be fully booted before the card is
inserted.‍
3 Follow the on-screen instructions.‍
4 Wait several minutes while the software update process
completes.‍
The device returns to normal operation after the software
update process is complete.‍
Remove the memory card.‍
5
NOTE: If the memory card is removed before the device
restarts fully, the software update is not complete.‍
Screenshots
You can capture a screenshot of any screen shown on your
chartplotter as a bitmap (.‍bmp) file.‍ You can transfer the
screenshot to your computer.‍
31
Capturing Screenshots
1 Insert a memory card into the card slot.‍
2 Select Settings > System > Display > Screenshot Capture
> On.‍
3 Go to a screen you want to capture.‍
4 Hold Home for at least six seconds.‍
Copying Screenshots to a Computer
1 Remove the memory card from the chartplotter, and insert it
into a card reader that is attached to a computer.‍
2 From Windows® Explorer, open the Garmin\scrn folder on
the memory card.‍
3 Copy a .‍bmp file from the card and paste it to any location on
the computer.‍
Type
Sentence
Description
Transmit
GPAPB
APB: Heading or track controller
(autopilot) sentence "B"
GPBOD
BOD: Bearing (origin to
destination)
GPBWC
BWC: Bearing and distance to
waypoint
Receive
32
Description
VDM
AIS VHF data-link message
You can purchase complete information about National Marine
Electronics Association (NMEA) format and sentences from: NMEA,
Seven Riggs Avenue, Severna Park, MD 21146 USA (www.nmea.org)
NMEA 2000 PGN Information
Type
PGN
Description
Transmit and receive 059392 ISO acknowledgment
059904 ISO request
060928 ISO address claim
126208 NMEA: Command, request, and
acknowledge group function
126996 Product information
NMEA 0183 Information
Type
Sentence
127250 Vessel heading
128259 Speed: Water referenced
128267 Water depth
129539 GNSS DOPs
129799 Radio frequency, mode, and power
130306 Wind data
130312 Temperature
Transmit
126464 Transmit and receive PGN list group
function
GPGGA
GGA: Global positioning system
fix data
GPGLL
GLL: Geographic position
(latitude and longitude)
GPGSA
GSA: GNSS DOP and active
satellites
GPGSV
GSV: GNSS satellites in view
129283 Cross track error
GPRMB
RMB: Recommended minimum
navigation information
129284 Navigation data
GPRMC
RMC: Recommended minimum
specific GNSS data
GPRTE
RTE: Routes
GPVTG
VTG: Course over ground and
ground speed
GPWPL
WPL: Waypoint location
GPXTE
XTE: Cross track error
PGRME
E: Estimated error
PGRMM
M: Map datum
PGRMZ
Z: Altitude
SDDBT
DBT: Depth below transducer
SDDPT
DPT: Depth
SDMTW
MTW: Water temperature
SDVHW
VHW: Water speed and heading
DPT
Depth
DBT
Depth below transducer
MTW
Water temperature
VHW
Water speed and heading
WPL
Waypoint location
DSC
Digital selective calling
information
DSE
Expanded digital selective calling
HDG
Heading, deviation, and variation
HDM
Heading, magnetic
MWD
Wind direction and speed
MDA
Meteorological composite
MWV
Wind speed and angle
127258 Magnetic Variance
129025 Position: Rapid update
129026 COG and SOG: Rapid update
129029 GNSS position data
129285 Navigation route and waypoint info
129540 GNSS satellites in view
Receive
127245 Rudder
127250 Vessel heading
127488 Engine parameters: Rapid update
127489 Engine parameters: Dynamic
127493 Transmission parameters: Dynamic
127498 Engine parameters: Static
127505 Fluid level
129038 AIS class A position report
129039 AIS class B position report
129040 AIS class B extended position report
129794 AIS class A static and voyage related
data
129798 AIS SAR aircraft position report
129802 AIS safety-related broadcast message
129808 DSC call information
130310 Environmental parameters
130311 Environmental parameters (obsolete)
130313 Humidity
130314 Actual pressure
130576 Small craft status
This data applies only to NMEA 2000-compatible products.‍
Appendix
Index
A
aerial photos 4
AIS 4, 5, 7
alarm 5
distress signal device 5
radar 18
SART 5
targeting 4, 5
threats 5, 18
turning on 30
vessels 5
alarms 29
anchor drag 29
arrival 29
collision 5
deep water 16
engine 12
gauges 12
navigation 29
off course 29
shallow water 16
sonar 16
water temperature 16
weather 29
anchor drag alarm 29
animated currents, tides 4
arrival alarm 29
Auto Guidance 8, 29
line 29
shoreline distance 30
autopilot 9
B
backlight 1
Bluetooth devices 22
buoy reports 25
C
celestial information 13
charts 2, 4, 6
appearance 6
built-in 3
details 3
heading line 6
navigation 3, 4
orientation 6
panning 2
selecting 3
symbols 2
clock 29
alarm 29
collision alarm 5
color mode 1
combinations 11
customizing 11
selecting 11
compass 11
compass rose 6
compass tape data bar 6
courses 8
current stations 13
indicators 4
D
data
backup 31
copying 30
data fields 6
data management 30
deleting, all user data 11
depth log 16, 17
destinations
navigation chart 8
selecting 8
device
keys 1, 2
registration 31
Index
digital selective calling 20, 21
channels 21
contacts 21
individual routine call 22
individual routine calls 21
turning on 20, 30
distress call 21
distress signal device 5
DownVü 14
DSC. See digital selective calling
E
EBL 18
adjusting 18
measuring 18
showing 18
EGNOS 26
engine gauges 12
configuring 12
status alarms 12
environment gauges 13
environmental gauges 13
EPIRB 5
event log 27
F
factory settings 30
sonar 16
Fish Eye 3D
sonar cone 7
suspended targets 7
tracks 7
fishing chart 2, 26
panning 2
setup 6
fuel alarm 12, 29
fuel capacity 12, 27
fuel gauges 12
configuring 12
status alarm 12, 29
synchronizing with actual fuel 12
fuel onboard 27
G
gauges
engine 12
environment 13
environmental data 13
fuel 12
limits 12
status alarms 12
trip 12
wind 12, 13
GLONASS 26
Go To 8
GPS
EGNOS 26
GLONASS 26
signals 1
WAAS 26
GPS accuracy 29
H
hazard colors 6
heading, line 7
home screen, customizing 2
I
icons 23
K
keel offset 27
keys 1
power 1
L
lane width 6
language 26
locking, screen 1
M
man overboard 9
marine services 8
mark location 9
media player 22, 23
alpha search 22
Android 22
device name 23
FUSION-Link 22
iPod 22
MTP 22
muting 23
preset 22
radio 22
repeating 22
shuffling 22
source 22
tuner region 22
tuning mode 22
VHF 23
Windows phone 22
zones 23
memory card 30, 31
detailed maps 31
installing 2
slot 1
Meteor. See media player
MOB, device 5
music player 22, 23, 26. See media player
N
navaids 3
navigation alarms 29
navigation chart 2, 4, 8, 26
aerial photos 6
marine service points 8
panning 2
radar overlay 18, 19
setup 6
vessel trails 7, 21
navigation inset 6
NMEA 0183 20, 28, 32
NMEA 2000 20, 28, 32
O
off course alarm 29
offset, front of boat 20
other vessels
AIS 7
trails 7
overlay numbers 6
P
Perspective 3D 26
photos, aerial 4
position report 21
position tracking 21
power key 1, 26
powerboat 27
premium charts 3, 4
aerial photos 4
Fish Eye 3D 7
tide and current indicators 4
product registration 31
R
radar 17
AIS 18
clutter 19, 20
color scheme 20
field of view 20
front-of-boat offset 20
gain 19
optimizing display 19
overlay screen 18, 19
range 17
range rings 20
sentry mode 17
timed transmit 17
transmitting 17
33
waypoints 18, 20
zoom scale 17
radar overlay 18
radio, SiriusXM 26
range rings 6
registering the device 31
routes
copying 30, 31
creating 9, 10
deleting 10
editing 10
navigating 10
navigating parallel to 10
viewing list of 10
waypoints 30
list 10
navigating 11
recording 11
saving 10
saving as route 11
showing 6, 10
transducer 13, 15, 16
trip gauges 12
S
vessel trails 7, 21
VHF radio 20
calling an AIS target 22
distress calls 21
DSC channel 21
individual routine call 22
individual routine calls 21
video 23
configuring 23
voltage 29
volume, adjusting 26
VRM 18
adjusting 18
measuring 18
showing 18
safe depth 29
safe height 29
safe zone collision alarm 5
sailboat 27
SART 5
satellite imagery 4
satellite signals, acquiring 1
screen
brightness 1
locking 1
screenshots 32
capturing 31, 32
sentry mode 17
guard zone 18
timed transmit 17, 18
settings 26–29
radar display 20
system information 27, 30
shoreline distance 30
SideVü 14
SiriusXM 23
SiriusXM Satellite Radio 26
software, updating 31
sonar 13
a-scope 15, 16
alarms 16
appearance 16
bottom lock 15
color gain 14
cone 7
depth 15
depth line 16
depth scale 15
DownVü 14
frequencies 15
gain 14
interference 16
noise 14, 16
overlay numbers 16
recording 16
scroll speed 16
SideVü 14
surface noise 16
suspended targets 16
views 14
waypoint 14
whiteline 16
zoom 15
SOS 9
suspended targets 7
symbols 4
system information 27, 30, 31
T
tide stations 3, 13
indicators 4
touchscreen 1
calibrating 31
tracks 10
clearing 11
copying 30, 31
deleting 11
editing 10
34
U
unit ID 27, 30
units of measure 29
updates, software 31
user data, deleting 11
V
W
WAAS 26
water
speed 27
temperature offset 27
water temperature log 16, 17
waypoints 9
copying 31
creating 9, 26
deleting 9
editing 9
man overboard 9
navigating to 9
radar 18
showing 6
sonar 14
tracked vessel 21
viewing list of 9
weather 26
weather 6, 23, 24
alarms 29
broadcasts 23
charts 26
fishing 25
fishing chart 26
forecast 24–26
navigation chart 26
overlay 26
precipitation 23, 24
sea conditions 25
subscription 23, 26
surface pressure 25
visibility 25
water temperature 25
wave information 25
winds 25
wind gauges 12, 13
wireless devices 28
Bluetooth devices 22, 28, 29
connecting a wireless device 22, 28
network configuration 28
Z
zoom
chart 2
radar 17
sonar 15
Index
www.garmin.com/support
913-397-8200
1-800-800-1020
0808 238 0000
+44 (0) 870 8501242
1-866-429-9296
+43 (0) 820 220230
+ 32 2 672 52 54
+385 1 5508 272
+385 1 5508 271
+420 221 985466
+420 221 985465
+ 45 4810 5050
+ 358 9 6937 9758
+ 331 55 69 33 99
+ 39 02 36 699699
(+52) 001-855-792-7671
0800 0233937
+47 815 69 555
00800 4412 454
+44 2380 662 915
(+35) 1214 447 460
+386 4 27 92 500
0861 GARMIN (427 646)
+27 (0)11 251 9999
+34 93 275 44 97
+49 (0)180 6 427646
20 ct./Anruf. a. d.
deutschen Festnetz,
Mobilfunk max. 60 ct./Anruf
+ 46 7744 52020
Garmin International, Inc.
1200 East 151st Street
Olathe, Kansas 66062, USA
Garmin (Europe) Ltd.
Liberty House, Hounsdown Business Park
Southampton, Hampshire, SO40 9LR UK
Garmin Corporation
No. 68, Zhangshu 2nd Road, Xizhi Dist.
New Taipei City, 221, Taiwan (R.O.C.)
© 2013 Garmin Ltd. or its subsidiaries