Wireless N Adapter RNX-N250PCe User Manual

Wireless N Adapter RNX-N250PCe
User Manual
Wireless N Adapter RNX-N250PCe
User Manual
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device
and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user
may be required to take adequate measures.
National Restrictions
2400.0-2483.5 MHz
Country
Restriction
Reason/remark
Bulgaria
France
General authorization required for outdoor use and public service
Outdoor use limited to 10 mW
Military Radiolocation use. Refarming of the 2.4 GHz band has
e.i.r.p. within the band 2454-2483.5
been ongoing in recent years to allow current relaxed regulation.
MHz
Full implementation planned 2012
Italy
If used outside of own premises, general authorization is
2
Wireless N Adapter RNX-N250PCe
User Manual
required
Luxembourg
General authorization required for network and service
supply(not for spectrum)
Norway
Implemented
This subsection does not apply for the geographical area within a
radius of 20 km from the centre of Ny-Ålesund
Russian
Only for indoor applications
Federation
Note: Please don’t use the product outdoors in France.
3
Wireless N Adapter RNX-N250PCe
User Manual
Table of Content
Table of Content...............................................................................................4
Chapter 1 Overview .........................................................................................5
Package Content ......................................................................................5
1.1
Overview of the Product.................................................................5
1.2
Features.........................................................................................6
1.3
System Requirement......................................................................6
1.4
Specification...................................................................................6
Chapter 2 Installation Guide ............................................................................8
2.1
Hardware Installation .....................................................................8
2.2
Software Installation.......................................................................9
Chapter 3 Wireless Connection Guide...........................................................13
3.1. Connecting with Microsoft Zero Configuration tool (Win XP) .......13
3.2. Connecting with Window 7...........................................................14
3.3. Connecting with Wireless LAN Utility ...........................................15
Chapter 4 Utility Configuration – Win XP’s Station Mode............................... 20
4.1. General ........................................................................................ 20
4.2. Profile........................................................................................... 21
4.2.1 Add ......................................................................................... 21
4.2.2 Remove .................................................................................. 23
4.2.3 Edit ......................................................................................... 23
4.2.4 Duplicate................................................................................. 24
4.2.5 Set default .............................................................................. 25
4.3. Available Network ........................................................................ 26
4.4. Status........................................................................................... 27
4.5. Statistics....................................................................................... 28
4.6.
Wi-Fi Protect Setup...................................................................... 29
4.6.1 Method 1 PIN Input Config (PIN) ............................................ 29
4.6.2 Method 2 Push Button ............................................................ 31
FAQ................................................................................................................ 33
Glossary......................................................................................................... 34
4
Wireless N Adapter RNX-N250PCe
User Manual
Chapter 1 Overview
Thank you for choosing Rosewill’s 802.11n 2T2R Wireless PCI-Express adapter –
RNX-N250PCE. RNX-N250PCE is a powerful 300Mbps Adapter for PCs without any
hassle. The Adapter can be used in Ad-Hoc mode to connect directly with other cards for
peer-to-peer file sharing or in Infrastructure mode to connect with a wireless access point
or router for access to the Internet in your office or home network. This chapter is to
introduce you more about this Wireless Adapter.
1.1
Package Content
Before getting started, please verify that your package includes the following items:
1. Rosewill RNX-N250PCE Wireless N Adapter x 1
2. 5 dBi Antenna x2
3. Low Profile Bracket x1
4. Quick Installation Guide x1
5. Resource CD x1, including:
z
Rosewill Wireless N Utility and Driver
z
User Manual
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or missing,
please contact with your distributor.
1.2
Overview of the Product
The adapter is an 802.11n client device; it is designed to provide a high-speed and
5
Wireless N Adapter RNX-N250PCe
User Manual
unrivaled wireless performance for your computer or notebook. With a faster wireless
connection, you can get a better Internet experience, such as downloading, gaming, video
streaming and so on.
With the 802.11n technology, higher throughput improvements using MIMO (multiple input,
multiple output antennas), the RNX-N250PCE’s transfer rate up to 300Mbps for maximum
throughput. It can also interoperate with other wireless (802.11b, 802.11g) products. The
adapter supports 64/128-bit WEP, WPA and WPA2 encryption to prevent outside intrusion
and protect your personal information from being exposed.
The adapter is easy to install and manage. The Quick Setup Wizard guides you
step-by-step through the installation process; the Rosewill Wireless N Client Utility helps
you create a wireless connection immediately.
With unmatched wireless performance, reception, and security protection, the
RNX-N250PCE is the best choice for easily adding or upgrading wireless connectivity to
your notebook and computer.
1.3
Features
z
Comply with IEEE 802.11b, 802.11g and 802.11n standard for 2.4GHz Wireless LAN
z
Support advanced 2 x 2 MIMO Technology with up to 300Mbps data transfer rate
z
Support 64/128-bit WEP,WPA and WPA2 wireless security modes
z
Windows 7-32/64 bit, Vista 32/64 bit, XP, 2000, Linux support
z
Supports Sony PSP X-link for online gaming
z
Supports roaming between access points when configured in Infrastructure mode
z
Easily connect and secure your wireless network with WPS (Wi-Fi Protected Setup)
1.4
System Requirement
You must have at least the following
z
A desktop PC with an available working PCI-Express slot
z
At least a 300MHz processor and 32MB of memory
z
Windows OS for Win98SE, ME, 2000, XP, Vista, Win7
z
A CD-ROM Drive
z
A 802.11n 、802.11g or 802.11b Wireless Access Point/Router (for infrastructure
Mode) or another 802.11n、802.11g or 802.11b wireless adapter (for Ad-Hoc;
Peer-to-Peer networking mode).
1.5
Specification
6
Wireless N Adapter RNX-N250PCe
Chipset
User Manual
Realtek RTL8192CE
Standard
IEEE 802.11n, IEEE 802.11g, IEEE 802.11b
Interface
PCI-E Interface
Frequency Range
2.412 - 2.4835GHz
802.11b: up to 18 ± 1 dBm
Wireless Transmit Power
802.11g: up to 14 ± 1 dBm
802.11n: up to 13 ± 1 dBm
Modulation Technology
OFDM/CCK
Security
Support 64/128 bit WEP, WPA-PSK/WPA2-PSK (TKIP and AES)
Antenna
2x 5dBi detachable Directional Antenna
Operating: 0°C~40°C (32℉~104℉)
Temperature
Storage: -20°C~70°C (-40℉~158℉)
Relative: 15% ~ 95%, Non-Condensing
Humidity
Storage: 5% ~ 90% Non-Condensing
Dimensions
Weight
1.8" x 2.9" (45 x 74 mm, excluded Antenna)
0.08 lbs. (40g, excluded Antenna)
7
Wireless N Adapter RNX-N250PCe
User Manual
Chapter 2 Installation Guide
2.1
1
Hardware Installation
Make sure the computer is turned off. Remove the expansion slot cover from the
computer.
(The Highlighted slots are the PCIe slot available for RNX-N250PCe to install)
2
Carefully slide RNX-N250PCe into the PCI-E slot. Push evenly and slowly and
ensure it is properly seated. (The PCB board is only for reference)
3
Secure the screw, then the antennas on.
4
Turn on your computer. Windows detects the new hardware and prompts for Driver
installation.
8
Wireless N Adapter RNX-N250PCe
2.2
User Manual
Software Installation
The following driver installation guide uses Windows XP as the presumed operation
system.
1.
The system finds the newly installed device automatically. Click Cancel to close this
window.
2.
Insert the Driver and Utility CD-ROM into the CD-ROM driver.
3.
The Wizard should run automatically, and 錯誤! 找不到參照來源。 should appear. If
not, click the Start button and choose Run. In the field that appears, enter
D:\autorun.exe (if ‘’D’’ is the letter of your CD-ROM drive).
4.
Click Install Driver Installation on the Wireless Client Configuration Utility dialogue
9
Wireless N Adapter RNX-N250PCe
User Manual
box, and then select the installing language from the next screen and click Next
button.
5.
Click Next
6.
Click Install to start installing
10
Wireless N Adapter RNX-N250PCe
User Manual
7.
Follow the InstallShield Wizard steps, and click Finish when done.
8.
Now your PC or notebook will restart automatically.
z
You may encounter warning windows like below, please select
“install this driver software anyway” for Win7, or “Continue Anyway”
for Vista or XP.
11
Wireless N Adapter RNX-N250PCe
User Manual
12
Wireless N Adapter RNX-N250PCe
User Manual
Chapter 3 Wireless Connection Guide
This chapter describes how to configure your Adapter for wireless connectivity on
your Wireless Local Area Network (WLAN) and use the data security encryption
features.
After Installing the Adapter, the Adapter’s tray icon will appear in your system tray. It
appears at the bottom of the screen, and shows the signal strength using color and
the received signal strength indication (RSSI).
- If the icon is purple, there is no connection.
- If the icon is white, the network is dropping off.
- If the icon is green, there is good signal strength.
- If the icon is green, there is excellent signal strength.
In the following instruction for making a network connection, we use the provided
Utility to configure your wireless network settings.
Note: You could use either the software we provide or Microsoft Zero Configuration
tool to configure this adapter.
3.1. Connecting with Microsoft Zero Configuration tool (Win XP)
After specifying the Microsoft Zero Configuration tool to configure your wireless
icon on system tray. Select “View Available Wireless
network, right click on the
Networks” to specify your wireless network.
The tool shows the available wireless networks. Select your demanding network to
connect with. To connect to a wireless network, please click Change advanced
settings to be compatible with your wireless network settings.
13
Wireless N Adapter RNX-N250PCe
User Manual
3.2. Connecting with Window 7
You can easily access to wireless with Win7. First, move your mouse to lower right
hand corner as below and click on the icon where arrow pointing to.
Click Refresh to get an update of your Wireless Network Connection. This should help
you search the SSID of the network you want to connect to.
Select your desired SSID, then Click “Connect”.
14
Wireless N Adapter RNX-N250PCe
User Manual
You will be prompt to ask you entering the network security key. Once entered, please
click OK to complete.
You should see below in a very short period and find out whether you are connected
or now.
3.3. Connecting with Wireless LAN Utility
We provide this Utility for users to connect to a wireless network easily. It provides
more information and configuration for this adapter. As default, the Utility is started
15
Wireless N Adapter RNX-N250PCe
User Manual
automatically upon starting your computer and connects to a connectable wireless
network with best signal strength and with no security setting.
3.3.1 Step 1: Search Available Network
First Select the Available Network option:
You will see a list of the SSID that your wireless adapter has scanned in your
surrounding area. You can also “Refresh” to see the most updated list.
3.3.2 Step 2: Select and Add to Profile
Select your desired SSID (the one you want to link with), then click Add to Profile.
16
Wireless N Adapter RNX-N250PCe
User Manual
After click “Add to Profile”, you will see the next window “Wireless Network Properties”
popup with your current wireless signal’s setting. (RNX-N180PCe will detect the
current setting of your SSID). So after the “Wireless Network Properties” popup, all
you need to do is to enter the password of your SSID and click OK to continute.
When done, your wireless adapter will automatically connect to this SSID. However,
Please do make sure returning to “Profile” and set your SSID Profile as your default.
So your utility will remember for the future to link to this SSID when computer is
Power-On.
Now you have complete the setup of the your wireless network. You should be ready
to surf!
17
Wireless N Adapter RNX-N250PCe
3.3.3
User Manual
In Windows 8
Windows 8 users may use the built-in wireless utility. Follow the steps below.
system.
1.
Click the icon
at the bottom of your screen, and a network list will appear at the
right side of your screen. Select your target network, and then click Connect.
2.
If the network is unencrypted, you will directly connect to it.
If the network is encrypted, enter the password (network security key) and then click
Next to continue.
Note: You can also push the WPS/QSS button on your router as hinted “You can also
connect by pushing the button on the router”. Then click Next to continue.
18
Wireless N Adapter RNX-N250PCe
3.
User Manual
When Connected appears behind the SSID (as shown below), you have successfully connected to the target network.
Note: If the adapter is connected to the network for the first time, you will be asked
whether to turn on sharing or connect to devices. Please select “Yes, ...”or “No, ...”
according to your Internet environment.
19
Wireless N Adapter RNX-N250PCe
User Manual
Chapter 4 Utility Configuration – Win XP’s
Station Mode
The Wireless Adapter provides two modes: Station mode and Access Point mode,
the default is Station mode under Window XP.
You can select connect wirelessly to your Wireless router/AP to connect to Internet in
station mode. But in the Access Point mode, the wireless adapter act as a wireless
access point which can share Internet connection with others. (Access Point Mode
requires Wired Connection)
4.1. General
The General tab displays current basic wireless connection information.
General Information
z
Status: Wireless network Associated, Ad-hoc Mode or Not Associated.
z
Speed: The data Tx rate and Rx rate of the current connection.
z
Type: The type of the current wireless connection , Infrastructures or ad hoc
z
Encryption: Current encryption.
z
SSID: The unique name of the wireless network to which the wireless adapter is
connecting.
z
Signal Strength: The signal quality of the current connection.
20
Wireless N Adapter RNX-N250PCe
z
User Manual
Link Quality: The link quality of the current wireless connection.
Network Address
z
MAC Address: The MAC Address of the Adapter.
z
IP Address: The IP Address of the Adapter.
z
Subnet Mask: The Subnet Mask of the Adapter.
z
Default Gateway: The Default Gateway address of the Adapter.
Others
z
Show Tray Icon: Show USB Wireless LAN Utility icon in the windows taskbar
notification area.
z
Disable Adapter: Disable the wireless adapter.
z
Radio off: Turn off the radio of the wireless adapter.
4.2. Profile
Using the Profile tab, you can add, remove, edit, duplicate, and set default a
profile.
4.2.1 Add
z
Create a new Infrastructure mode profile
If you want your wireless computers to communicate with other computers on your
wired network via a wireless access point. Click the Add button to create a new
infrastructure profile.
21
Wireless N Adapter RNX-N250PCe
User Manual
When the Network Info dialog box appears, enter a name for the new profile. Enter the
Network SSID. Choose the Network Authentication Mode and Data encryption from
the drop-down menu and import the network key. Then click OK button.
z
Create a new ad-hoc mode profile
If you want your wireless computers communicate with each other directly, click the
Add button to create a new ad-hoc profile. Then, check on below option:
then select the correct operating channel for your network from the Channel
drop-down menu.
Choose the Network Authentication Mode and Data encryption from the drop-down
22
Wireless N Adapter RNX-N250PCe
User Manual
menu. And import the network key. Then click OK button. You have successfully
created a profile.
4.2.2 Remove
Select a profile and click Remove button to delete this profile.
4.2.3 Edit
Select a profile and click Edit button to edit this profile.
23
Wireless N Adapter RNX-N250PCe
User Manual
Modify the profile information according to your demand.
4.2.4 Duplicate
Select a profile which you want to copy and then click Duplicate
24
Wireless N Adapter RNX-N250PCe
User Manual
Import the new profile name in the popup window blank
4.2.5 Set default
When you want to make one profile as a default wireless connection, you should
select the profile and click Set default button. The wireless adapter will use this profile
to connect to wireless network automatically when the utility running next time.
25
Wireless N Adapter RNX-N250PCe
User Manual
4.3. Available Network
The Available Network tab displays a list of infrastructure and ad-hoc networks for
available wireless connection
Double-click the network to which you wish to connect.
26
Wireless N Adapter RNX-N250PCe
User Manual
Choose the Authorization modes and Encryption modes in the drop-down box. If the
wireless network uses a Passphrase, enter the Passphrase in the Passphrase field. If
the wireless network uses a WEP key, enter the WEP key in the Key field. Click the
OK button to complete the network connection.
4.4. Status
The Status tab displays the detailed information of current device and wireless
connection.
27
Wireless N Adapter RNX-N250PCe
User Manual
4.5. Statistics
The Statistics tab display the stat. value of current wireless connection Tx and Rx, you
can click Reset button to reset value and restart to count.
28
Wireless N Adapter RNX-N250PCe
User Manual
4.6. Wi-Fi Protect Setup
4.6.1 Method 1 PIN Input Config (PIN)
1.
Input the wireless NIC’s PIN Code into AP and click Start PIN on the AP-Router
29
Wireless N Adapter RNX-N250PCe
User Manual
WPS config page
2.
Click Pin Input Config(PIN)
3.
Select one WPS AP which you want connect to and click Select button
30
Wireless N Adapter RNX-N250PCe
4.
User Manual
Please wait when the PIN Method Window pop-up appear, the secure connection
between AP and wireless NIC will be founded automatically.
4.6.2 Method 2 Push Button
1.
Click Push Button Config(PBC) on Wi-Fi Protect Setup page
2.
Click Start PBC on the AP-Router WPS config page
31
Wireless N Adapter RNX-N250PCe
3.
User Manual
Please wait when the PBC method window pop-up appear, the secure connection
between AP and wireless NIC will be founded automatically.
Remark
If there is more than one AP on the PBC mode, there will be session overlap. Please
using method 1 PIN Input Config(PIN) or wait for a while push the button again.
32
Wireless N Adapter RNX-N250PCe
User Manual
FAQ
This chapter provides solutions to problems that may occur during the installation
and operation of the Wireless USB Adapter. Read the descriptions below to solve your
problems.
1. I cannot communicate with the other computers linked via Ethernet
in the Infrastructure configuration.
z
Make sure that the PC to which the Adapter is associated is powered on.
z
Make sure that your Adapter is configured on the same channel and with the
same security options as with the other computers in the Infrastructure
configuration.
2. What should I do when the computer with the Adapter installed is
unable to connect to the wireless network and/or the Internet?
z
Check that the LED indicators for the broadband modem are indicating
normal activity. If not, there may be a problem with the broadband
connection.
z
Check that the LED indicators on the wireless router are functioning properly.
If not, check that the AC power and Ethernet cables are firmly connected.
z
Check that the IP address, subnet mask, gateway, and DNS settings are
correctly entered for the network.
z
In Infrastructure mode, make sure the same Service Set Identifier (SSID) is
specified on the settings for the wireless clients and access points.
z
In Ad-Hoc mode, both wireless clients will need to have the same SSID.
Please note that it might be necessary to set up one client to establish a
BSS (Basic Service Set) and wait briefly before setting up other clients. This
prevents several clients from trying to establish a BSS at the same time,
which can result in multiple singular BSSs being established, rather than a
single BSS with multiple clients associated to it.
z
Check that the Network Connection for the wireless client is configured
properly.
z
If Security is enabled, make sure that the correct encryption keys are
entered on both the Adapter and the access point.
33
Wireless N Adapter RNX-N250PCe
User Manual
Glossary
z
802.11b - The 802.11b standard specifies a wireless product networking at 11
Mbps using direct-sequence spread-spectrum (DSSS) technology and operating
in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security.
802.11b networks are also referred to as Wi-Fi networks.
z
802.11g - specification for wireless networking at 54 Mbps using direct-sequence
spread-spectrum (DSSS) technology, using OFDM modulation and operating in
the unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE
802.11b devices, and WEP encryption for security.
z
802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO
(multiple-input multiple-output). MIMO uses multiple transmitter and receiver
antennas to allow for increased data throughput via spatial multiplexing and
increased range by exploiting the spatial diversity, perhaps through coding
schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) was
formed to help accelerate the IEEE 802.11n development process and promote a
technology specification for interoperability of next-generation wireless local area
networking (WLAN) products.
z
Ad-hoc Network - An ad-hoc network is a group of computers, each with a
Wireless Adapter, connected as an independent 802.11 wireless LAN. Ad-hoc
wireless computers operate on a peer-to-peer basis, communicating directly with
each other without the use of an access point. Ad-hoc mode is also referred to as
an Independent Basic Service Set (IBSS) or as peer-to-peer mode, and is useful
at a departmental scale or SOHO operation.
z
DSSS - (Direct-Sequence Spread Spectrum) - DSSS generates a redundant bit
pattern for all data transmitted. This bit pattern is called a chip (or chipping code).
34
Wireless N Adapter RNX-N250PCe
User Manual
Even if one or more bits in the chip are damaged during transmission, statistical
techniques embedded in the receiver can recover the original data without the
need of retransmission. To an unintended receiver, DSSS appears as low power
wideband noise and is rejected (ignored) by most narrowband receivers.
However, to an intended receiver (i.e. another wireless LAN endpoint), the DSSS
signal is recognized as the only valid signal, and interference is inherently
rejected (ignored).
z
FHSS - (Frequency Hopping Spread Spectrum) - FHSS continuously changes
(hops) the carrier frequency of a conventional carrier several times per second
according to a pseudo-random set of channels. Because a fixed frequency is not
used, and only the transmitter and receiver know the hop patterns, interception of
FHSS is extremely difficult.
z
Infrastructure Network - An infrastructure network is a group of computers or
other devices, each with a Wireless Adapter, connected as an 802.11 wireless
LAN. In infrastructure mode, the wireless devices communicate with each other
and to a wired network by first going through an access point. An infrastructure
wireless network connected to a wired network is referred to as a Basic Service
Set (BSS). A set of two or more BSS in a single network is referred to as an
Extended Service Set (ESS). Infrastructure mode is useful at a corporation scale,
or when it is necessary to connect the wired and wireless networks.
z
SSID - A Service Set Identification is a thirty-two character (maximum)
alphanumeric key identifying a wireless local area network. For the wireless
devices in a network to communicate with each other, all devices must be
configured with the same SSID. This is typically the configuration parameter for a
wireless PC card. It corresponds to the ESSID in the wireless Access Point and
to the wireless network name. See also Wireless Network Name and ESSID.
35
Wireless N Adapter RNX-N250PCe
z
User Manual
WEP - (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit
or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11
standard. To gain access to a WEP network, you must know the key. The key is a
string of characters that you create. When using WEP, you must determine the
level of encryption. The type of encryption determines the key length. 128-bit
encryption requires a longer key than 64-bit encryption. Keys are defined by
entering in a string in HEX (hexadecimal - using characters 0-9, A-F) or ASCII
(American Standard Code for Information Interchange – alphanumeric
characters) format. ASCII format is provided so you can enter a string that is
easier to remember. The ASCII string is converted to HEX for use over the
network. Four keys can be defined so that you can change keys easily.
z
Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the
Wireless Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an
industry standards group promoting interoperability among 802.11b devices.
z
WLAN - (Wireless Local Area Network) - A group of computers and associated
devices communicate with each other wirelessly, which network serving users
are limited in a local area.
z
WPA - (Wi-Fi Protected Access) - A wireless security protocol use TKIP
(Temporal Key Integrity Protocol) encryption, which can be used in conjunction
with a RADIUS server
Thank you for purchasing a quality Rosewill Product.
Please register your product at : www.rosewill.com for complete warranty information and future support for your
product.
CA PROP 65 WARNING:
This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
36