Christie Mirage 4K25 User Manual

Mirage 4K25
User Manual
020-101361-02
Mirage 4K25
User Manual
020-101361-02
NOTICES
COPYRIGHT AND TRADEMARKS
Copyright ©2015 Christie Digital Systems USA Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may
not be reflected in this document. Christie reserves the right to make changes to specifications at any time without notice. Performance
specifications are typical, but may vary depending on conditions beyond Christie's control such as maintenance of the product in
proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no
warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.
Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or
use of this material. Canadian manufacturing facility is ISO 9001 and 14001 certified.
WARRANTY
Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your
Christie dealer or Christie. In addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the
extent relevant or applicable to your product, the warranty does not cover:
a. Problems or damage occurring during shipment, in either direction.
b. Projector lamps (See Christie’s separate lamp program policy).
c. Problems or damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp other than a Christie
lamp supplied by Christie or an authorized distributor of Christie lamps.
d. Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras,
DVD players, etc., or use of a product with any non-Christie interface device.
e. Problems or damage caused by the use of any lamp, replacement part or component purchased or obtained from an
unauthorized distributor of Christie lamps, replacement parts or components including, without limitation, any distributor offering
Christie lamps, replacement parts or components through the internet (confirmation of authorized distributors may be obtained
from Christie).
f. Problems or damage caused by misuse, improper power source, accident, fire, flood, lightning, earthquake or other natural
disaster.
g. Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service
personnel or a Christie authorized repair service provider.
h. Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been
designed, modified or approved by Christie for such use.
i. Problems or damage caused by use of a projector in the presence of an oil-based fog machine or laser-based lighting that is
unrelated to the projector.
j. For LCD projectors, the warranty period specified in the warranty applies only where the LCD projector is in “normal use” which
means the LCD projector is not used more than 8 hours a day, 5 days a week.
k. Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such
product is protected from precipitation or other adverse weather or environmental conditions and the ambient temperature is
within the recommended ambient temperature set forth in the specifications for such product.
l. Image retention on LCD flat panels.
m.Defects caused by normal wear and tear or otherwise due to normal aging of a product.
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not
apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office
in the country where the end user is located or (ii) the required international warranty fee has been paid.
The warranty does not obligate Christie to provide any on site warranty service at the product site location.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your product. Please see the Maintenance
section for specific maintenance items as they relate to your product. Failure to perform maintenance as required, and in accordance
with the maintenance schedule specified by Christie, will void the warranty.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial
environment. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of the product in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at the user’s own expense.
CAN ICES-3 (A) / NMB-3 (A)
이 기기는 업무용 (A 급 ) 으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며 , 가정 외의 지역에서
사용하는 것을 목적으로 합니다 .
Environmental
The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol
means
that electrical and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product
appropriately and according to local regulations. In the European Union, there are separate collection systems for used electrical and electronic
products. Please help us to conserve the environment we live in!
Addendum
Translated copies of this document are provided on the CD in the back of this document. The CD may also
contain additional product documentation. Read all instructions before using or servicing this product.
本文档的翻译副本在本文档背面的 CD 上提供。该 CD 中还可能包含其他产品文档。使用或维修本产
品之前请务必阅读所有说明。
文件背面的光碟提供了本文件的翻譯副本。這張光碟可能另外包含其他產品文件。請先閱讀所有指
示再使用或送修本產品。
Le CD au dos de ce document contient des traductions de celui-ci dans différentes langues. Ce CD peut
également contenir de la documentation supplémentaire sur le produit. Lisez toutes les instructions avant
d'utiliser ou d'entretenir ce produit.
Übersetzte Versionen dieses Dokuments werden auf der CD auf dem Vorsatzblatt dieses Dokuments
bereitgestellt. Die CD kann auch zusätzliche Produktdokumentation enthalten. Bitte lesen Sie diese
Anweisungen vor der Verwendung dieses Produkts oder vor der Ausführung von Wartungsarbeiten am
Produkt.
Le copie tradotte di questo documento sono fornite sul CD, sul retro di questo documento. Il CD potrebbe
anche contenere altra documentazione sul prodotto. Si prega di leggere tutte le istruzioni prima di
utilizzare questo prodotto o sottoporlo a manutenzione.
このドキュメントの翻訳版がこのドキュメントの裏面の CD で提供されています。CD には追加の
製品マニュアルも収められています。この製品を使用したり、機能させたりする前に、すべての
指示をお読みください。
이 문서의 번역된 사본이 이 문서 후면의 CD 에서 제공됩니다 . 이 CD 에는 추가 제품 설명서가 포함되
어 있을 수 있습니다 . 이 제품을 사용하거나 수리하기 전에 모든 지침을 확인하십시오 .
Copias traduzidas deste documento são fornecida no CD contido na parte de trás deste documento. O CD
pode conter documentação adicional do produto. Leia todas as instruções antes de usar ou prestar serviço
com este produto.
Перевод данного документа представлен на компакт-диске на оборотной стороне документа.
Компакт-диск может также содержать дополнительную документацию по продукту. Перед
использованием или обслуживанием продукта ознакомьтесь со всеми инструкциями.
Las copias traducidas de este documento se proporcionan en el CD que se encuentra en la parte trasera. En
el CD también puede encontrar documentación adicional del producto. Lea todas las instrucciones antes
de utilizar o realizar el mantenimiento de este producto.
Перекладені екземпляри цього документа містяться на компакт-диску, який додано до цього
документа. На компакт-диску може також бути додаткова документація до виробу. Перш ніж
користуватися виробом або його обслуговувати, прочитайте всі інструкції.
Content
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Safety and warning guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installation safety and warning guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
AC/power precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Lamp precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Product safety labels
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Projector overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Contact your dealer
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
How the projector works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
List of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Site requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Physical operating environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
External exhaust ducting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Tools required for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Projector components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Position the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Connect to AC power
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adjust the projector tilt and level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Install the foot extension rods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Install the touch panel controller
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Remove the projector shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Set up the lens
Portrait mode
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3D setup for Mirage projectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3D requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Active stereo 3D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Passive stereo 3D configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3D system timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3D input video configurations
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Set up a single Mirage 4K to display 3D content . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
9
Content
Confirm the emitter setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Configure the projector for the 3D source . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Connect Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Input video mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Four-Port: 3GIC, TDPIC, THIC cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Four-Port: DDIC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Two-Port: TDPIC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Two-Port: DDIC card
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Connect a video source using DisplayPort
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Connect a video source using 3G Input card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Connect a video source using HDMI
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Connect a video source using DVI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Select a video source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Connect devices to the 3D Sync ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Connect a computer or server
Set up the ethernet
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Adjust the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Select screen image orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Maximize light output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Align the image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Adjust offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Adjust horizontal boresight
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Adjust vertical boresight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Lock the lens offsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Adjust DMD convergence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Color correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Adjust color by temperature
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Adjust color by precise chromaticity values . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Adjust color by saturation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Adjust the fold mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Projector LED status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Turn the projector on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
LED expected behavior on power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Turn the projector off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Work with lamps
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
10
Content
Adjust lamp power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Adjust the lamp position with LampLOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Calibrate the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Manually adjust the lamp position
View lamp information
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Track lamp intensity with LiteLoc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Lamp details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Record new lamp information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Add lamp end-of-life indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Work with lenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Select a channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Enable warping and blending . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Send error notifications to specified devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Touch panel controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Tab structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Menu tab details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Status tab details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Backup, Restore, and Upgrade Projector Files . . . . . . . . . . . . . . . . . . . . . 63
Upgrade the projector software
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Back up projector settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Export backup settings to an external device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Restore settings from a local backup profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Restore default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Import file from an external device to restore settings . . . . . . . . . . . . . . . . . . . . . . 64
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Maintenance shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Ventilation and cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Inspect and clean the airflow interlocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Inspect and clean the exhaust duct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Inspect and clean the lamp blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Inspect and fill the coolant reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Remove the liquid cooling reservoir
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Filtration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Replace the light engine air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Replace the liquid cooling air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
11
Content
Replace the laminar airflow device filter
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Adjust the yoke assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Inspect and clean the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Remove dust from the projection lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Remove fingerprints, smudges, or oil from the projection lens . . . . . . . . . . . . . . 74
Remove the projection lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Install the projection lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Calibrate the lens motors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Reset lens to home position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Projector does not power on
Lamp does not ignite
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Lamp suddenly turns off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Flicker, shadows or dimness
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
LampLOC not working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Touch panel controller is blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Blank screen, no display of image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Cannot communicate with projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Inaccurate display colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Display is not rectangular . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Display has suddenly frozen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Display is jittery or unstable
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Incoming signal(s) problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Touch panel controller or projector head problems on startup . . . . . . . . . . . . . . . . . 79
The Projector LEDs or the MCPU board power LED are not on . . . . . . . . . . . . . . . 79
The MCPU board power LED is not on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
MCPU board power LED behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Touch panel controller does not connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
3D synchronization problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Left and right eye are reversed
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Frame multiplication applied to incoming video signals when not required . . . . . . . . 80
Run the projector interrogator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Save TPC log files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Mirage signal connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
12
Content
Optional Input cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Control signal compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Temperature sensor thresholds
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Warning thresholds for fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Warning threshold for liquid cooling module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Touch panel controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Regulatory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Safety
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Electro-magnetic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
13
Introduction
This manual is intended for professionally trained operators of Christie high-brightness projection
systems. These operators are qualified to replace the lamp and air filters, but should not attempt to
install or service the projector.
Only accredited Christie technicians who are knowledgeable about the hazards associated with
high-voltage, ultraviolet exposure, and the high temperatures generated by the projector lamp are
authorized to assemble, install, and service the projector.
For complete Mirage 4K25 product documentation and technical support, go to
www.christiedigital.com.
Safety and warning guidelines
This projector must be operated in an environment that meets the operating range specification.
Use only the attachments and/or accessories recommended by Christie. Use of others may result in
the risk of fire, shock, or personal injury.
Warning! Failure to comply with the following could result in death or serious injury.
• Never look directly into the projector lens or at the lamp. The extremely high brightness can cause
permanent eye damage. For protection from ultraviolet radiation, keep all projector housings intact
during operation. Protective safety gear and safety goggles are recommended when servicing.
• FIRE HAZARD! Keep hands, clothes, and all combustible material away from the concentrated light
beam of the lamp.
Caution! Failure to comply with the following could result in minor or moderate injury.
• Position all cables where they cannot contact hot surfaces or be pulled or tripped over.
• The American Conference of Governmental Industrial Hygienists (ACGIH) recommends
occupational UV exposure for an 8-hour day to be less than 0.1 microwatts per square centimeters
of effective UV radiation. A workplace evaluation is advised to assure employees are not exposed to
cumulative radiation levels exceeding the government guidelines for your area. Be aware that
some medications are known to increase sensitivity to UV radiation.
NOTE: During maintenance and cleaning operations, the instructions define that the unit must not be
operational, thus the lamps are not active and there are no emissions. Optical adjustments are not
considered maintenance. The lamps are turned on during optical adjustments and emissions are
present.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
14
Introduction
Installation safety and warning guidelines
Danger! Failure to comply with the following results in death or serious injury.
• This product must be installed within a restricted access location which is normally inaccessible by
the general public, including workers, visitors, and residents in the immediate vicinity, by means of
engineering or administrative control measures but is accessible to authorized personnel that may
not have specific safety training.
• This product must be located and positioned in a way as to restrict audience members from direct
access to enter the light beam path.
• Do not install the projector overhead.
• When installing the projector in portrait mode, the device holding the projector must have a weight
rating sufficient to hold the weight of the projector. The projector weighs 125kg (275 lbs).
• The projector uses a high-pressure lamp that may explode if improperly handled. Always wear
manufacturer approved protective safety clothing (gloves, jacket, face shield) when the lamp door
is open or when handling the lamp. Failure to comply results in death or serious injury.
Warning! Failure to comply with the following could result in death or serious injury.
• A qualified technician is required for all installations.
• SHOCK HAZARD. Never operate the projector without all of its covers in place.
• Use of the projector’s rear safety strap is mandatory to prevent the projector from tipping.
Secure the strap between the projector and the surface it is mounted to.
• Four or more people are required to safely lift and hand-carry one projection head a short distance.
Christie recommends removing the lamp before transporting the projector.
• Two or more people are required to safely lift and hand-carry the lamp power supply (LPS).
Notice. Failure to comply with the following may result in property damage.
• Perform an automatic LampLOC adjustment when the lamp is moved, leveled, or a new lamp is
installed in the projector.
• Keep the projector level when lifting or transporting. Avoid tilting the projector to the right. This
can introduce an air bubble into the coolant hoses that can result in an air lock and the overheating
of the projector.
AC/power precautions
To correctly install this projector, a certified electrician must install a permanent three-phase
connection to the lamp power supply (LPS). The LPS projector outlet is used to supply power to the
projector head. Operate the projector at the recommended voltage.
Danger! Failure to comply with the following results in death or serious injury.
Disconnect projector from AC before opening any enclosure.
Warning! Failure to comply with the following could result in death or serious injury.
• Verify that the projector is using a line cord, socket, and power plug that meets the appropriate
local rating standards. Use only an AC power cord recommended by Christie. Do not attempt
operation if the AC supply and cord are not within the specified voltage and power range.
• Do not allow anything to rest on the power cord. Locate the projector where the cord cannot be
abused by persons walking on it or objects rolling over it. Never operate the projector if the power
cable appears damaged in any way.
• Do not overload power outlets and extension cords as this can result in fire or shock hazards.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
15
Introduction
Lamp precautions
Lamps used in the projector are under high pressure and must be handled with caution. Lamps can
explode and cause serious personal injury if dropped or mishandled.
Danger! Failure to comply with the following results in death or serious injury.
• Never attempt to access the lamp compartment while the lamp is on. Wait at least 10 minutes after
the lamp turns off before powering down, disconnecting from AC, and opening the lamp door.
• The arc lamp operates at a high pressure that increases with temperature. Failure to allow the lamp
to sufficiently cool before handling, increases the potential for an explosion causing personal injury
or property damage.
• Always wear manufacturer approved protective safety clothing (gloves, jacket, face shield) when
the lamp door is open or when handling the lamp. Only qualified technicians should install projector
lamps.
Warning! Failure to comply with the following could result in death or serious injury.
• Possibly hazardous optical radiation emitted from this product. (Risk group 3)
• Thermal radiation emitted from this product may cause burns. (Risk group 3)
i
Recommended protective clothing includes, but may not be limited to a polycarbonate face shield,
protective gloves, and a quilted ballistic nylon jacket or a welder’s jacket. This equipment is included
in included in the Christie Protective Clothing Safety kit
P/N: 598900-095.
Christie’s protective clothing recommendations are subject to change. Any local or federal
specifications take precedence over Christie recommendations.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
16
Introduction
Product safety labels
Indicates the presence of a grounding point.
Indicates the presence of an earth grounding point.
Indicates the presence of a dangerous condition or situation.
Indicates the presence of a pinch hazard. To avoid personal injury, keep hands clear and loose clothing
tied back.
Indicates the presence of a hot surface. To avoid personal injury, always allow the projector to cool
down for a minimum of 10 minutes before performing maintenance or service procedures.
Indicates the presence of a hot surface. To avoid personal injury, always allow the projector to cool
down for a minimum of 10 minutes before performing maintenance or service procedures.
Indicates the presence of an electrical shock hazard. To avoid personal injury, always disconnect all
power sources before performing maintenance or service procedures.
Indicates the presence of an electrocution hazard. To avoid personal injury, always disconnect all power
sources before performing maintenance or service procedures.
Indicates the presence of moving fan blades. To avoid personal injury, keep hands clear and loose
clothing tied back. Always disconnect all power sources before performing maintenance or service
procedures.
Indicates exposure to bright light. To avoid personal injury, never look directly at the light source.
Indicates the presence of an explosion hazard. To avoid personal injury, always disconnect all power
sources and wear Christie approved protective clothing.
Indicates the presence of a fire hazard. To avoid personal injury and property damage, always adhere
to the instructions described in this manual.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
17
Introduction
Always disconnect all power sources before performing maintenance or service procedures.
See the product user manual for specific information and directions.
See the product service manual for specific information and directions.
Never look directly into the projector lens. The extremely high brightness can
cause permanent eye damage.
This label warns of a cross-connection hazard
when installing multiple projectors at once. A fire
hazard exists if a lamp power supply interlock
cable is connected to a different projector than its
lamp power cables.
For more information, see Adjust the projector tilt
and level in the Installation and Setup chapter
Projector overview
The Mirage 4K25 is a professional quality, easy-to-use, split-body projector using Digital Light
Processing (DLP™) technology from Texas Instruments. Integrating smoothly into traditional
projection environments; the Mirage 4K25 interfaces with local networks throughout the world, for
multimedia presentations from a variety of formats, to offer stunning wide screen, high-resolution
4K images at 120 frames per second.
Contact your dealer
If you encounter a problem with your Christie projector, contact your dealer. To assist with the
servicing of your projector, enter the information in the tables below and keep this information with
your records.
Purchase Record
Dealer:
Dealer or Christie Sales/Service contact phone number:
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
18
Introduction
Purchase Record
Projector serial number:
Purchase date:
Installation date:
*The serial number can be found on the license label located on the front panel
Ethernet Settings
Default gateway
Projector IP address
Subnet mask
Key features
•
3-chip 4K DLP™ light engine
•
4096 x 2160 native pixel format
•
2.0 and 3.0 kW Xenon lamps available
•
Display of stereoscopic 3D video
•
Warp and blend of projected images
•
Supports screens up to approximately 100 feet in width
•
Touch panel controller (TPC) for main projector interface. Verify you have the latest software by
visiting http://www.christiedigital.com
•
1x 10/100BaseT Ethernet port
•
RS232 ports for communication
•
4x Option slots accepting a variety of digital video input option cards
•
3D Sync input/output port
•
LiteLOC™ feature for constant image brightness
•
LampLOC™ feature for motorized three-axis lamp alignment
•
Electronically operated “quick” douser
•
Motorized lens mount
•
LED indicators on the rear corners of the projector for easy-to-read status indication
•
Replaceable air filters (no tools required)
•
Optional rack mount stand
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
19
Introduction
•
Choice of field-interchangeable zoom lenses
Model Name
Part Number
Mirage 4K25
129-012104-XX
How the projector works
The Mirage 4K25 accepts a variety of input signals for projection on front or rear projection screens,
typical in commercial or other large screen applications. High-brightness light is generated by a
short arc Xenon lamp, then modulated by three Digital Micromirror Device (DMD) panels responding
to incoming data streams of digitized red, green and blue color information. As these digital
streams flow from the source, light from the responding “on” pixels of each panel is reflected,
converged and then projected to the screen through one or more projection lenses, where all pixel
reflections are superimposed in sharp full-color images.
List of components
Verify the following components were received with the projector:
•
Touch panel controller (TPC)
•
Lens plug (required for shipping when lens is not installed to prevent contamination of critical
optical components)
•
Light engine removal tool
•
Convergence tool
•
Nylon safety strap with clip (required to secure projector to tabletop or optional rack mount)
•
Warranty card
•
Shroud
•
Access keys
•
Web registration form
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
20
Installation and Setup
This section explains how to install, connect, and optimize the projector display.
Site requirements
To safely install and operate the projector, the installation location must have restricted access for
authorized personal only and meet these minimum requirements.
Physical operating environment
•
Maximum Ambient Temperature (operating) 35°C (95°F)
•
Minimum Ambient Temperature (operating) 10°C (50°F)
External exhaust ducting
The installation site must provide a minimum of 450 CFM (ft 3/min) external exhaust airflow to
ensure adequate cooling of the Xenon arc lamp at less than or equal to 25°C (77°F) ambient and
less than 3,000 ft (914.4 m) elevation. Above 25°C or 3,000 ft, 600 CFM is required.
For more details, see Connect external exhaust ducting on page 28.
Power connection
The requirements listed below are applicable for permanently wired installation or power cord
connection:
•
Terminal block, electrician hard-wired to the projector head.
•
Electrical rating: 200 - 240 VAC, 23 A max.
•
This product can be connected to an IT power distribution system.
Tools required for installation
•
12” screwdrivers: Phillips #2 (magnetic) and flat
•
19mm and 7/8” wrenches
•
Assorted Allen keys (metric)
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
21
Installation and Setup
•
Christie approved protective safety clothing if working with the lamp
•
Lens cleaning tissue and solution
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
22
Installation and Setup
Projector components
D
B
LAMP SIDE
C
F
E
B
A
G
J
H
LENS SIDE
I
ID
Item
Description
A
Touch panel controller (TPC)
A touch-sensitive screen used to control and monitor operation. For
information about TPC controls and settings, see Menus on page 58.
B
LED status indicators
LED color and blinking rates (located in both back corners of the projector)
provide information about the status of the projector. For information about
projector states and status, see LED expected behavior on power up on
page 53.
C
Manual douser override
Closing the douser rotates a shutter blade in front of the lamp and reduces
the lamp power to 2.0 kW to conserve lamp life. The override is for
emergency use only.
D
Lamp door and lamps
The lamp door provides access to the lamp compartment and must remain
closed and locked for normal operation. Lamp replacement should only be
performed by qualified technicians. For a complete list of available lamp
types, see Accessories on page 92.
E
Exhaust duct and vane switch
Extracts heated air from the lamp compartment. The vane switch mounted
inside the rigid port monitors airflow. See Site requirements on page 21.
F
Liquid cooling air filter Cover
and air filter
Filters air before it circulates to cool the heat exchanger. For replacement
instructions, see Inspect and clean the lamp on page 72.
G
Shroud (two-piece)
Covers the motorized lens mount assembly.
H
Projection lens
A variety of lenses can be used with the D4K2560Mirage 4K25. For a list of
available lenses, see on page 94
I
Air filter cover and air filter
Filters the intake air before it circulates through the front compartment to
cool the main electronics. For replacement instructions, see Inspect and
clean the lamp on page 72.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
23
Installation and Setup
ID
J
Item
Description
Input panel faceplate
Provides a variety of ports for connecting external devices. For information
about connecting devices and inputs, see Connect Devices on page 37.
Position the projector
i
Keep the projector lens as perpendicular to the screen as possible, even if significantly above the
screen center. When a particularly short throw distance combines with a wide screen, you may have
to forfeit some aim and stay more perpendicular to the screen. In such cases, some lens offset can
reduce the keystone distortion.
1. Position the projector at an appropriate throw distance (projector-to-screen distance) and
vertical position. Ideally, center the projector with the screen. If space is limited, aim the
projector slightly off-center. This increases side keystoning, but reduces the horizontal lens
offset required.
90°
≠90°
2. If using an optional rack stand (P/N: 108-282101-02), assemble the rack stand using the
instructions provided with the rack stand. Use the hold down clamp (P/N: 116-100101-01)
when securing the projector to the rack stand.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
24
Installation and Setup
Connect to AC power
Failure to comply with the following could result in death or serious injury.
• Certified electrician required during installation. Ground (earth) connection is necessary for
safety. Never compromise safety by returning the current through the ground. Connect
ground first to reduce shock hazard.
• Use an appropriate strain relief connector on the AC supply cable to prevent the cable from
rubbing against the LPS knockout plate and becoming damaged.
When connecting the projector directly to AC power, follow all electrical codes for your
location. In addition, follow these recommendations:
• Use 10AWG or 8AWG wiring. The distance between the wall circuit breaker and the
projector must not exceed 20 meters using 10AWG cables or 30 meters using 8AWG cables.
• For North American installations, use at least 10AWG copper wires for the connection of the
main AC supply to the projector’s ground lug.
• Copper or aluminum are acceptable as conductor wiring material to the terminal block.
When connecting the projector to AC power with a pluggable type-B cable, follow all electrical
codes for your location. In addition, follow these recommendations:
• There must be easy access to the current protection device or breaker in the building.
• Use minimum 10AWG wiring, with a maximum length of 4.5 m for U.S and Canada. For
international installations the length should be based on the local electrical codes.
• The socket-outlet is installed near the equipment and is easily accessible.
• The plug can be used as the device disconnect and is near the unit and easily accessible.
The circuit breaker on the projector baseplate (located under the front lens-side corner) can
also be used as a means of disconnect.
1. On the bottom of the projector in the front lamp-side corner, loosen the two screws and slide
the access panel to expose the terminal block.
2. Remove four screws securing the knockout plate to the bottom right corner of the front bezel.
Remove the knockout plate. The AC supply is routed to the terminal block through an
appropriate strain relief mounted on this knockout plate.
2
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
1
25
Installation and Setup
3. Connect to the terminal block.
The terminal block accommodates up to an eight
AWG wire. If required, use a 90° strain relief
connector to route the power cable in a downward
direction.
i
Always connect the ground lead first to reduce shock hazard.
•
If connecting to permanent power, connect the AC power
source to the terminal block, beginning with the ground
lead.
•
If connecting to a pluggable type-B cable, connect the cable
to the terminal block, beginning with the ground lead.
•
Use an appropriately sized strain relief connector with the knockout plate provided to
ensure adequate environmental sealing and to prevent the cables from wear and
accidentally being torn out.
3
4. Reinstall the knockout plate and secure it with four screws.
5. Reinstall the bottom access panel over the terminal block and secure it with two screws.
If using a pluggable type-B cable, connect to the building’s AC power source.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
26
Installation and Setup
Adjust the projector tilt and level
Warning! Failure to comply with the following could result in death or serious injury.
• The projector’s rear safety strap must be in place before adjusting the projector feet.
• Do not over-extend the feet. Make sure several threads are engaged into the projector’s baseplate
to secure the projector from falling.
Adjust the projector tilt to fill the maximum amount of screen while minimizing keystone. Lens offset
can be used to center the image in the center of the screen..
Notice. Failure to comply with the following may result in property damage.
The front-to-back tilt of the projector must not exceed 15 degrees.
1. Secure a safety lifting strap rated to handle the projector weight at the rear of the projector.
2. Hoist up the projector.
3. To adjust the vertical or horizontal position of the projector, extend or retract the adjustable feet
on the bottom of the projector (A).
4. Once the required adjustment is made, tighten the lock nut against
the bottom of the projector (B).
The projector provides 4 inches of adjustment at the front and 11.5
inches of adjustment at the rear.
B
5. If the vertical or horizontal position of the projector requires more
adjustment than the standard feet allow, two 6-inch extension rods
can be installed to increase the amount of available adjustment.
A
Install the foot extension rods
1. Elevate the rear of the projector to access the two rear feet.
2. Remove the feet by loosening the lock nut and rotating the each foot out of the projector.
3. Add the extension rods to the standard feet.
4. Thread the extended feet into the projector’s baseplate.
5. Adjust the feet until the required tilt is achieved.
6. Lock the feet in place by turning each lock nut until it fits tight against the projector.
3
2
1
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
19 mm
27
Installation and Setup
Install the touch panel controller
1. Loosen the mounting arm just enough for the end to fit over the ball joint located on the rear
panel of the projector.
The touch panel controller (TPC) becomes loose from the mounting arm when the mounting
arm lock is loosened.
2. Tighten the mounting arm lock until it fits tightly on the joint.
The TPC safety strap comes installed on the projector ball point.
3. Connect the cable from the touch panel controller (TPC) to the connector on the rear panel of
the projector.
4. Adjust the TPC angle for optimal viewing, then tighten the mounting arm lock securely so that
the TPC is held in place at the required location.
Connect external exhaust ducting
Warning! Failure to comply with the following could result in death or serious injury.
At minimum, a 10-inch (25.4 cm) long, strong metal duct must be installed at the projector
and installed to an outside venting duct system to prevent glass shards from exiting the duct
in the event of a lamp explosion.
Notice. Failure to comply with the following may result in property damage.
*600 CFM is required in projection rooms with an ambient temperature above 25°C or
located at an elevation greater than 3000 feet above sea level.
Connect the existing outside-venting duct to the 8-inch
diameter exhaust port on the top of the projector. Make sure
there are no obstructions or bends in the ducting or air
intakes and the vane switch at the exit duct moves freely.
The pre-installed outside-venting duct should be rigid at the
projector and must also include a heat extractor and blower
that maintains a minimum of 450 CFM* when the projector is
operating at less than or equal to 25°C (77°F) ambient and
less than 3,000 feet (914.4 m), when measured at the
projector exhaust opening.
To determine the projector exhaust CFM value, use an airflow
meter to measure the ft/min at the rigid end of the open
exhaust duct that connects to the projector. Take the
measurement at the end of the duct without the projector
connected.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
28
Installation and Setup
Use this formula to determine the CFM value for the projector: CFM = 0.35 × Measured ft/min
Lamp Type
Min. Airflow (CFM) Required
2.0 kW
450 CFM*
3.0 kW
450 CFM*
*600 CFM is required in projection rooms with ambient temperature above 25°C
(77°F) or elevation (above sea level) greater than 3000 feet (914.4 m).
Add an extractor or a booster if there is insufficient airflow. Do not mount the extractor on the
projector as this may introduce some vibration into the image.
Notice. Failure to comply with the following may result in property damage.
Never disable the vane switch. Attempting to operate the projector with inadequate airflow
can result in dangerous overheating of the projector.
i
To prevent the projector from overheating or becoming unsafe, an alarm sounds if the duct
is obstructed or a fan fails. Christie recommends regularly verifying that the exhaust is
unobstructed and functioning correctly.
Remove the projector shroud
Warning! Failure to comply with the following could result in death or serious injury.
• Never install the shroud for overhead installations.
The lens side shroud must be removed to gain access to the lens. The other shroud must be
removed when connecting the AC power cord into the front face of the projector.
1. Use finger pressure to push down on the shroud clips located at the top and bottom of the
shroud as shown by the arrows.
2. Carefully slide the shroud sideways and forward away from the lens mount and lens.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
29
Installation and Setup
2
1
3. Place the shroud covers on a clean surface to prevent scratches.
Set up the lens
Warning! Failure to comply with the following could result in death or serious injury.
• Keep fingers and other body parts away from the moving parts in the projector. Motors and fans
may start without warning.
• Tie back long hair, remove jewelry and loose clothing before manually adjusting the projector.
•
Notice. Failure to comply with the following may result in property damage.
The lens seals the projection head, preventing contaminants from entering the main electronics area.
Do not operate the projector without a lens installed. Use a lens plug when installing or transporting
the projector.
1. Remove the projector shroud.
2. Make sure the lens locking lever is in the up position.
3. If attached, remove the rear lens cap from the lens.
4. Slide the lens into the lens mount, aligning all connections.
i
Always install the lens with UP label in the top position to achieve consistent boresight
alignment each time the lens is replaced.
5. Secure the lens with the lens locking lever (down position).
6. Calibrate the lens motors.
For more details, see Work with lenses on page 56, Remove the projector shroud on page 29, and
Calibrate the lens motors on page 75.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
30
Installation and Setup
Portrait mode
1. Orient the projector in the frame with the lamp door facing downward (as shown).
The maximum tilt angle is ±15 degrees.
2. Set up the customer-supplied mounting frame.
The mounting frame must be designed to accommodate the weight and mounting provisions of
the projector.
3. Remove the projector feet.
4. Attach the projector to the mounting frame using the four M12 holes (normally used for
projector feet) on the bottom side of the projector.
Mounting bolts must be grade 8.8 or higher and torqued to 60 ft-lbs.
5. Perform a lamp alignment.
3D setup for Mirage projectors
The Mirage projector is capable of displaying stereoscopic 3D video sources, relying on additional
hardware (stereo emitters and glasses) to complete the display system.
Images generated from a stereo 3D video source consist of a series of images (frames) that
alternate quickly between two slightly different viewpoints, corresponding to our left and right eyes.
When these frames are displayed fast enough and viewed with special glasses synchronized to the
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
31
Installation and Setup
left/right (L/R) changes, the resulting image appears with the same depth and perspective sense in
the real world.
The type of 3D glasses can be active or passive stereo depending on the type of stereo controllers and
screen used.
i
3D requirements
Stereo 3D applications require a stereo 3D-capable source, special hardware and software setups,
and the projector’s 3D Settings menu option to control the projector’s processing, synchronization,
and displaying of the stereoscopic 3D source material.
Hardware requirements
Note the following hardware requirements for stereo 3D applications:
•
Christie Digital Systems Mirage 4K Series projector
•
3D stereo sync cable for Direct-Input 3D (and frame doubled)
•
A source, usually a computer with a 3D graphics card(s)
•
Emitter for controlling active shutter glasses
or
A qualified device that mounts in front of the lens of the projector to process the light from the
lens into a passive polarized light. Contact your Immersive dealer for more information.
Software and content requirements
Note the following software and content requirements for stereo 3D applications:
•
Any 3D computer software that supports 3D stereo on a supported computer(s) with associated
graphic cards (suggested cards include ATI or NVIDIA)
•
A video stream from a video source prepared to be sequential content (for Direct-Input 3D) or
two video streams from a video source that has been prepared to be supplied left eye and right
eye concurrently and frame locked (Dual-Input 3D)
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
32
Installation and Setup
Active stereo 3D configuration
The following diagram shows the typical hardware configuration for active stereo 3D systems:
i
In response to the 3D Sync Out signal from the projector, the IR emitter emits an infrared signal to a
receiver in the active 3D shutter glasses. This synchronizes the active glasses to alternatively open
and close for the active stereo 3D applications.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
33
Installation and Setup
Passive stereo 3D configuration
The following diagram shows the typical hardware configuration for passive stereo 3D systems:
i
For operation with passive glasses, a 3D polarization filter is placed in front of the lens and is
synchronized to the projected frames with the 3D Sync Out signal.
3D system timing
Consult the documentation for your glasses or polarization filter and keep their specifications in
mind when configuring the projector for 3D operation. The projected video must be optimized for
the glasses’ shutter speed or polarization filter performance to prevent obvious “ghosting” of the
video content (known as cross-talk in stereo 3D applications) or other more subtle color artifacts.
Visual performance can be optimized by adjusting the Dark Interval and the 3D Sync Delay
settings.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
34
Installation and Setup
3D input video configurations
The stereo 3D input video stream may be supplied from the video server to the projector in two
configurations: Direct-Input 3D or Dual-Input 3D.
Configuration
Description
Direct-Input 3D
In this configuration a single video stream is provided by the video server, with the left
eye and right eye frames supplied as alternate frames within the video stream. A 3D
Input Sync may be used to identify the left eye frames.
The Direct-Input 3D video stream may be supplied by either a Four-Port input video
configuration (such as four cables each supplying one quadrant of the image) or an OnePort input video configuration (such as one cable supplying the entire frame).
Dual-Input 3D
In this configuration two video streams are provided by the video server, with the left
eye supplied by one stream and the right eye supplied by the other. The video streams
are frame locked and supplied concurrently.
The Dual-Input 3D video streams may be supplied by either two Four-Port input video
configurations (such as four cables each supplying one quadrant of the image for each
eye, with a total of eight cables) or two One-Port input video configurations (such as one
cable supplying the entire frame for each eye, with a total of two cables).
Set up a single Mirage 4K to display 3D content
The projector must be installed correctly to display 2D content (lamp installed, optically aligned,
focused, and so on) before completing the following steps to display the 3D content:
1. Confirm the emitter setup.
2. Configure the projector for the 3D source.
Confirm the emitter setup
1. To set the 3D output to emitter, tap Main > 3D Settings > 3D Sync Output and select To
Emitter.
2. To enable the 3D test pattern, tap Main > 3D Settings and select 3D Test Pattern.
3. To configure the dark interval so the amount of dark time aligns with the amount of time
required for the glasses to switch, tap Main > 3D Settings > Dark Interval and adjust the
dark interval as required.
4. View the displayed test pattern. If you can see both Ls and Rs with both eyes, increase the dark
interval until Ls are only visible to the left eye and Rs are only visible to the right eye.
5. Optionally, adjust the 3D Sync delay as necessary.
This adjusts the timing of the sync pulse in relation to the dark time transition on the DMDs.
Use the default value of 0 as a starting point.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
35
Installation and Setup
Configure the projector for the 3D source
1. Select the channel (from the Home tab) best suited for the 3D source.
2. To select the correct EDID timing, tap Main > Configuration > EDID Timing Select and
select the required EDID timing.
3. Connect all the required cables between the 3D source and the projector.
4. Configure your 3D source.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
36
Connect Devices
This section provides information and procedures for connecting external devices to the projector.
Communication and input ports are located on the projector side input panel, accessed by removing
the input panel cover. When connecting devices, you can route cables through the opening in the
frame to the side input panel or directly to the video option cards and MCPU. The image below
shows the video option card slot numbers and the MCPU panel.
Input signal devices are connected to the video option cards and the option card slot numbers are
important for some types of input signals. Communication devices are connected at the MCPU
panel.
Input video mapping
Video input mapping depends on the type of cards used for the Four-Port or Two-port input
configurations.
Four-Port: 3GIC, TDPIC, THIC cards
The following table shows the video quadrant mappings for the 3GIC, TDPIC, and THIC Four-Port
input configurations:
Four-Port Input Configuration—Two Cards (1)
Quadrants
Columns
Slot 1
1-In
Top left
1 (left most)
Slot 1
2-In
Bottom left
2
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
37
Connect Devices
Slot 2
1-In
Top right
3
Slot 2
2-In
Bottom right
4
Four-Port Input Configuration—Two Cards (2)
Quadrants
Columns
Slot 3
1-In
Top left
1 (left most)
Slot 3
2-In
Bottom left
2
Slot 4
1-In
Top right
3
Slot 4
2-In
Bottom right
4
Four-Port Input Configuration—Four Cards
Quadrants
Columns
Slot 1
1-In
Top left
1 (left most)
Slot 2
1-In
Top right
2
Slot 3
1-In
Bottom left
3
Slot 4
1-In
Bottom right
4
Four-Port: DDIC card
The following table shows the video quadrant mappings for the DDIC Four-Port input configuration:
Four-Port Input Configuration
Quadrants
Columns
Slot 1
1-Dual Link DVI-I
Top left
1 (left most)
Slot 2
1-Dual Link DVI-I
Top right
2
Slot 3
1-Dual Link DVI-I
Bottom left
3
Slot 4
1-Dual Link DVI-I
Bottom right
4
Two-Port: TDPIC card
Two-Port Input Configuration—Two Cards (1)
Columns
Slot 1
1-In
1 (left most)
Slot 2
1-In
2
Two-Port Input Configuration—Two Cards (2)
Columns
Slot 3
1-In
1 (left most)
Slot 4
1-In
2
Two-Port: DDIC card
Two-Port Input Configuration—Two Cards (1)
Columns
Slot 1
1-Dual Link DVI-I
1 (left most)
Slot 2
1-Dual Link DVI-I
2
Two-Port Input Configuration—Two Cards (2)
Columns
Slot 3
1 (left most)
1-Dual Link DVI-I
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
38
Connect Devices
Slot 4
1-Dual Link DVI-I
2
Connect a video source using DisplayPort
The Twin DisplayPort Input card (TDPIC) accepts digital video data from the DisplayPort sources.
The input configurations listed below are supported.
Input
Configuration
Description
Requirements
Four-Port
Enables connection of four DisplayPort cables to two or four TDPIC
cards. Each DisplayPort input supplies one quadrant or column of a 4K
input image. This configuration supports high resolution and high
frame rate input video streams.
Two or four TDPIC
cards
Four-Port, DualInput 3D
May be used for Dual-Input 3D configurations.
Four TDPIC cards
Two Port
Enables connection of two DisplayPort cables to two TDPIC cards. Each
DisplayPort input supplies one of two columns of a 4K input image.
Two TDPIC cards
Two-Port Dual
Input 3D
May be used for Dual-Input 3D configurations.
Four TDPIC cards
One-Port
Enables connection of one DisplayPort cable to the 1-IN input of a
TDPIC card (any slot). In this configuration the DisplayPort input
supplies the entire video raster.
One TDPIC card
One-Port, DualInput 3D
May be used for Dual-Input 3D configurations.
One TDPIC card
For information on the video quadrant mapping for Four-Port and Two-Port configurations, see TwoPort: TDPIC card on page 38 and For limitations of one card use for One-Port Dual-Input 3D, see
Mirage signal connectivity on page 84.
Connect a video source using 3G Input card
The 3G Input card (3GIC) accepts digital video data from HD and 3G-SDI (Serial Digital Interface)
sources. The input configurations listed below are supported.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
39
Connect Devices
Input
Configuration
Description
Requirements
Four-Port
Enables connection of four SDI cables to two 3GIC cards. Each SDI
input supplies one quadrant or column of a 4K input image. This
configuration supports high resolution and high frame rate input
video streams.
Two 3GIC cards
Four-Port, DualInput 3D
May be used for Dual-Input 3D configurations.
Four 3GIC cards
One-Port
Enables connection of one SDI cable to the 1-IN input of a 3GIC card
(in any slot). In this configuration the SDI input supplies the entire
video raster.
One 3GIC card
One-Port, DualInput 3D
May be used for Dual-Input 3D configurations.
One 3GIC card
For information on the video quadrant mapping for Four-Port and Two-Port configurations, see TwoPort: TDPIC card on page 38 and For limitations of one card use for One-Port Dual-Input 3D, see
Mirage signal connectivity on page 84.
Connect a video source using HDMI
The Twin HDMI Input card (THIC) accepts digital video data from HDMI sources. The input
configurations listed below are supported.
Input
Configuration
Description
Requirements
Four-Port
Enables connection of four HDMI cables to two THIC cards. Each
HDMI input supplies one quadrant or column of a 4K input image.
This configuration supports high resolution and high frame rate input
video streams.
Two THIC cards
Four-Port, DualInput 3D
May be used for Dual-Input 3D configurations.
Four THIC cards
One-Port
Enables connection of one HDMI cable to the 1-IN input of a THIC
card (in any slot). In this configuration, the HDMI input supplies the
entire video raster.
One THIC card
One-Port, DualInput 3D
May be used for Dual-Input 3D configurations.
One THIC card
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
40
Connect Devices
For information on the video quadrant mapping for Four-Port and Two-Port configurations, see TwoPort: TDPIC card on page 38 and For limitations of one card use for One-Port Dual-Input 3D, see
Mirage signal connectivity on page 84.
Connect a video source using DVI
The Dual Link DVI Input card (DDIC) accepts digital video data from DVI sources. It does not
support incoming analog signals. The input configurations listed below are supported.
Input
Configuration
Description
Requirements
Four-Port
Enables connection of four DVI cables to four DDIC cards. Each DVI
input supplies one quadrant or column of a 4K input image. This
configuration supports high resolution and high frame rate input video
streams.
Four DDIC cards
Two Port
Enables connection of two DVI cables to two DDIC cards. Each DVI
input supplies one of two columns of a 4K image.
Two DDIC cards
Two-Port DualInput 3D
May be used for Dual-Input 3D configurations.
Four DDIC cards
One-Port
Enables connection of one DVI cable to the DVI input of a DDIC card
(in any slot). In this configuration, the DVI input supplies the entire
video raster.
One DDIC card
One-Port, DualInput 3D
May be used for Dual-Input 3D configurations.
Two DDIC cards
Dual Link DVI Input
Analog
PWR
1 - Dual Link DVI-I
Digital
2 - VGA
Signal
Only one Four-Port input configuration is available for DVI inputs. For information on the video
quadrant or column mapping for the DDIC input configuration, see Two-Port: TDPIC card on page
38.
Select a video source
After connecting a video source to the projector, you must select it using the touch panel controller
(TPC).
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
41
Connect Devices
1. On the TPC, select Input > Channel.
2. Scroll the list of channels until you find the channel that best matches your configuration.
3. Tap the channel.
An image appears on the screen. If an image does not appear on the screen, repeat steps 1 to
3, selecting a different channel.
Connect devices to the 3D Sync ports
The 3D Sync Input and Output ports located on the MCPU faceplate provide a convenient method
for interfacing the projector to the 3D stereo projection system. The 3D Sync Input should be
connected to the video source for synchronization of the left eye/right eye frames of Direct input 3D
or for frame doubled content. The 3D Sync Input is not required for Dual-Input 3D. The 3D Sync
Output is available for control of an IR Emitter for active glasses or a polarization device for passive
glasses.
Connect a computer or server
To communicate with a remote computer, server or an existing network, use an RJ-45 cable to
connect the Ethernet hub or switch to the Ethernet port, located on the projector MCPU faceplate.
When using the Christie serial protocol over Ethernet, connect to port 3002.
For applications or equipment using serial communications, use the Christie-proprietary serial
protocol to communicate with the RS422 port or the RS232 ports on the MCPU faceplate.
Notice. Failure to comply with the following may result in property damage.
The RS232 port located on the MCPU faceplate uses Christie-proprietary protocol and is intended for
Christie accessories or automation controllers only. For more information on the serial commands,
see the Mirage 4K Serial API Commands Technical Reference (P/N: 020-101449-XX).
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
42
Connect Devices
Set up the ethernet
Ethernet is setup to obtain an IP address automatically if a DHCP server is on the network. To
modify IP settings, or manually enter an address.
1. On the touch panel controller, tap Menu > Configuration > Ethernet Settings > Modify
IP Settings.
2. Set the network information for the projector:
•
To obtain information automatically from the network, tap Automatic.
•
To manually enter the network information, tap Manual and enter the IP Address,
Subnet Mask and Gateway (optional).
3. Click Ok.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
43
Adjust the Image
This section provides information and procedures for adjusting the projector image.
Select screen image orientation
The projector supports front projection, rear projection, front projection inverted, and rear
projection inverted.
1. On the touch panel controller, tap Menu > Configuration > Screen Image Orientation.
2. Select the required orientation from the list.
Maximize light output
To ensure optimal operation, use LampLOC to adjust the lamp position whenever a new lamp is
installed or changes in the projector orientation (for example, from/to portrait mode).
1. On the touch panel controller, tap Menu > Lamp > LampLOC.
2. Tap Auto LampLOC.
Align the image
This procedure ensures that the image reflected from the digital micromirror device (DMD) is
parallel and centered with the lens and screen. Complete this procedure before adjusting boresight.
1. Verify that the projector is properly located and positioned relative to the screen.
2. Display a test pattern that can be used to analyze image focus and geometry.
3. Perform a preliminary focus and (if available) a zoom adjustment with the primary lens
installed. Always focus the center of the image first.
4. With the test pattern on screen, re-check the projector leveling so the top edge of the image is
parallel to the top edge of the screen.
For more details, see Position the projector on page 24 and Work with lenses on page 56.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
44
Adjust the Image
Adjust offset
Project an image with the primary lens. Always adjust offset before adjusting boresight.
Select a framing test pattern and then adjust the vertical (A) and horizontal (B) offsets to display a
square image on the screen, with minimal projector aiming error.
A
B
i
For the best optical performance and minimal keystone, use offsets instead of aiming at the center of
the image, in off-axis installations.
Avoid extreme tilts or offsets. Corner vignettes on a white test pattern indicate extreme offset that
should be avoided using mechanical alignment.
Adjust horizontal boresight
Warning! Failure to comply with the following could result in death or serious injury.
When doing optical adjustments on an operating projector and the top lid is removed, everyone
within the immediate vicinity must wear safety glasses with side shields and Christie approved
protective safety clothing (P/N: 598900-95).
The purpose of boresight adjustment is to balance the tilt of the lens mount to compensate for screen-toprojector tilt.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
45
Adjust the Image
1. Loosen the lens mount stabilization screw (D).
A
D
C
B
2. Loosen the horizontal lock screw (A).
3. Extend the lens focus (B) completely.
4. Adjust the Focus using the focus knob to retract the lens. Watch the image at the left edge of
the screen until it comes into focus. If the entire screen is in focus, proceed to step 7.
5. Continue retracting the lens.
a. If the right side of the image comes into focus before the lens is completely retracted,
adjust the horizontal boresight bolt (C) to balance the left and right edges.
6. If the right side of the image fails to focus, adjust the horizontal boresight bolt (C).When both
sides appear equally blurry, adjust the offsets to re-center the image.Repeat steps 1 to 5 until
both sides of the image are focused.
7. Tighten the lock screw (A) and the lens mount stabilization screw (D) to maintain the
adjustments.
8. Check the boresight again.
9. Unless proceeding to adjust vertical boresight, perform a lens calibration.
For more details, see Calibrate the lens motors on page 75.
Adjust vertical boresight
Warning! Failure to comply with the following could result in death or serious injury.
When doing optical adjustments on an operating projector and the top lid is removed, everyone
within the immediate vicinity must wear safety glasses with side shields and Christie approved
protective safety clothing (P/N: 598900-95).
1. Focus the image at the top edge of the screen
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
46
Adjust the Image
2. Loosen the lens mount stabilization screw (D).
D
B
C
A
3. Loosen the vertical lock screw (A).
4. Extend the lens focus (B) completely.
5. Adjust the Focus knob to retract the lens. Watch the image at the top edge of the screen until
it comes into focus. If the entire screen is in focus, proceed to step 8.
6. Continue retracting the lens.
a. If the bottom edge of the image comes into focus before the lens is completely retracted,
adjust the vertical boresight bolt (C) to direct or aim the lens mount UP towards the top
of the screen to balance out the top/bottom edges.
b. If the top edge of the image is not in focus, adjust the vertical boresight bolt (C) to direct
or aim the lens mount toward the bottom of the screen.
7. When both sides appear equally blurry, adjust the horizontal and/or vertical offset to re-center
the image on the screen.
8. Repeat Steps 2 to 5 until the top and bottom of the screen are both well-focused.
9. Re-focus the center of the image. The goal is for good focus at the center and on all sides.
10. Tighten the lock screw (A) and the lens mount stabilization screw (D) to maintain the
adjustments.
11. Check the boresight again.
12. Perform a lens calibration.
For more details, see Calibrate the lens motors on page 75.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
47
Adjust the Image
Lock the lens offsets
The lens locking feature reduces image vibration. For most applications lens locking is not necessary.
Warning! Failure to comply with the following could result in death or serious injury.
When doing optical adjustments on an operating projector and the top lid is removed, everyone
within the immediate vicinity must wear safety glasses with side shields and Christie approved
protective safety clothing (P/N: 598900-95).
Notice. Failure to comply with the following may result in property damage.
Lens locking requires the disabling of the lens offset and focus. Do not attempt to adjust the lens
offset with the offset locking screws installed.
1. Use the touch panel controller (TPC) or manually adjust the lens offsets to the required position.
2. Unpack and install the three lens offset locking screws.
3. Tighten each locking screw until each screw contacts the lens offset collar.
4. With equal pressure, tighten each locking screw against the lens offset collar.
5. Disconnect the lens motor communication cable.
i
When the lens motor communication cable is disconnected, the projector displays an error
message on the TPC or the LCD display, identifying the loss of communication with the lens
mount motors. Ignore this error message.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
48
Adjust the Image
Adjust DMD convergence
A convergence problem occurs when one or more projected colors (red, green, blue) appears
misaligned when examined with a convergence test pattern. Normally, the three colors should
overlap precisely to form pure white lines throughout the image and one or more poorly converged
individual colors may appear adjacent to some or all of the lines.
Contact your Christie accredited service technician to correct DMD convergence issues.
Color correction
The Mirage 4K25 provides predefined and custom color adjustments using the Color Correction
menu. The available color adjustment controls are listed in the table below:
Menu
Description
Max Drives
Turns off all color adjustments allowing the projector to run at maximum brightness.
Color Temperature
Allows the specification of a color temperature as expressed in degrees Kelvin. Standard
settings are:
• 9300K—Close to the white of many computer monitors.
• 6500K—Standard for color video in both standard and HD formats.
• 5400K—Standard for graphics and black and white video.
• 3200K—Useful if the projected image is to be filtered, or shot as part of a studio set
illuminated with incandescent lighting.
HD Video
Sets the output color value to the HD video standard.
Custom
Allows custom color adjustments to be made by the projector operator.
Adjust color by temperature
i
Color temperature adjusts the overall color gamut and does not allow for precise adjustments of
specific primary colors.
1. On the touch panel controller, tap Menu > Configuration > Color Correction > Select
Color Adjustment.
2. From the list, select Color Temperature.
3. Tap Color Temperature.
4. Adjust the temperature value and tap OK.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
49
Adjust the Image
Adjust color by precise chromaticity values
i
Adjusting the color chromaticity values overwrites any settings applied in the Color Saturation menu.
1. On the touch panel controller, tap Menu > Configuration > Color Correction > Select
Color Adjustment.
2. From the list, select Custom.
3. Tap Color Adjustments by X,Y.
4. Adjust the precise hues of each primary color component.
Adjust color by saturation
i
Adjusting the color saturation overwrites any settings applied in the Color Adjustments by X,Y menu.
1. On the touch panel controller, tap Menu > Configuration > Color Correction > Select
Color Adjustment.
2. From the list, select Custom.
3. Tap Color Saturation.
4. Adjust the hue of each primary color by using more or less of it in relation to the other primary
colors.
Adjust the fold mirror
Warning! Failure to comply with the following could result in death or serious injury.
When doing optical adjustments on an operating projector and the top lid is removed, everyone
within the immediate vicinity must wear safety glasses with side shields and Christie approved
protective safety clothing (P/N: 598900-95).
If a corner or edge of an image is missing, the fold mirror might be misaligned with the optical
system. To correct this issue:
1. Remove the four screws securing the fold mirror plate, on the underside of the projector.
2. Adjust the fold mirror:
•
Adjust the screw on the lens side to raise or lower the image.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
50
Adjust the Image
•
Adjust the screw on the lamp side to move the image left or right.
Base of projector
FRONT
3mm
hex
driver
image
image
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
51
Operation
This section provides information and procedures for operating the projector.
Projector LED status indicators
LED
State
Description
Solid Green
On
Video electronics are on, the lamp is on.
Solid Yellow
Standby mode
Video electronics are off, lamp is off.
Solid Green, Yellow and Red
AC is on
MCPU board software has not started initialization.
Flashing Green
Warm up
Video electronics are initializing, lamp is striking and
warming up.
Flashing Yellow
Cool down
Lamp is off, video electronics and lamp are cooling
down.
Flashing Red
Alarm or warning preset
Problem with the projector must be addressed.
Flashing Green and Yellow
AC on to standby
MCPU board software has started initialization.
Turn the projector on
Warning! Failure to comply with the following could result in death or serious injury.
• Do not attempt to turn the projector on if the AC supply is not within the specified voltage range.
1. Set the breaker switch on the projector baseplate to the on position.
2. When the projector reaches standby, on the touch panel controller, tap Home > Power.
For more details on the specified voltage range, see Power requirements on page 90.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
52
Operation
LED expected behavior on power up
The following table shows the expected behavior of the projector LED and the MCPU board power
LED on power up:
Action/Event
Projector LEDs
MCPU Board Power LED
Applying AC power to the projector head
Solid red
Yellow
Solid green
Solid yellow
Within the first second
Solid red
Blinking green
Solid green
Solid yellow
At approximately 30 seconds
Off red
Blinking green
Blinking yellow
Blinking green
At approximately 50 seconds
Off/blinking red
Solid green
Solid yellow
Off green
At approximately one minute and 15 seconds, the TPC indicates that it is connected and shows the
home page.
Turn the projector off
1. On the touch panel controller, tap the Home tab.
2. Tap Power.
i
When powering off in preparation for inspection or maintenance, always disconnect from AC
and set the projector breaker to the off positions.
Work with lamps
This section provides information and procedures for optimizing lamp performance to ensure the
brightest, most uniform image possible for the life of the lamp.
Adjust lamp power
1. On the touch panel controller, tap Menu > Lamp > Lamp Power.
2. Use the slider or enter a value to adjust the lamp power.
3. Tap OK.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
53
Operation
Adjust the lamp position with LampLOC
Use LampLOC to configure the lamp position and geometry when installing a new lamp in the
projector or at any other time when the lamp performance needs to be optimized. Before adjusting
LampLOC, make sure the following criteria is met:
1. Make sure the lamp is on and the douser (shutter) is open during adjustment.
Christie recommends a 10-minute warm-up.
2. Perform the LampLOC procedure.
For more details, see Calibrate the lamp below.
Calibrate the lamp
The lamp should be re-calibrated when any of the following conditions are met:
•
After the lamp has been replaced.
•
After the projector has been moved and/or jostled.
•
After the lamp motor IMCB has been replaced.
1. On the touch panel controller, tap Menu > Lamp > LampLOC.
2. Tap Auto LampLOC.
3. Adjust optical components if required.
Manually adjust the lamp position
1. On the touch panel controller, tap the Home tab.
2. Tap Test Pattern and select 17pt White Field Test Point.
3. Mount a light meter on a tripod and center it with the lens.
The distance from the lens does not matter. An attenuator or an internal foil aperture may be
required
4. Tap Menu > Lamp > LampLOC.
5. Tap the directional arrows to adjust the value displayed in the Z field, until the brightness
reading in front of the lens is maximized.
6. Tap the directional arrows to adjust the values displayed in the X and Y fields until the
brightness values in each field are maximized.
7. For a finer adjustment, repeat steps 5 and 6 but take the readings at the center of the screen
instead of at the lens.
View lamp information
To view a history of all previously installed lamps, on the touch panel controller, tap Menu > Lamp
> Lamp History.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
54
Operation
Track lamp intensity with LiteLoc
Use the LiteLoc feature to maintain a constant level of brightness over the lifetime of the lamp.
1. On the touch panel controller, tap Menu > Lamp > Lamp Power.
2. To adjust the lamp power, use the slider or enter a value until the display is as bright as
required.
3. Tap OK.
4. Tap Lamp Mode.
5. Tap Constant Intensity.
Notice the Lamp Power option is greyed out so you cannot adjust it. To readjust the lamp
power, select Lamp Mode > Lamp Power. From the Lamp Power option, adjust the power
setting as applicable.
Lamp details
Lamp Type
Replace Before
Min. Lamp Power
Max. Lamp Power
CDXL-20 (2.0 kW)
2400 hours
1000W (50%)
2200W (110%)
CDXL-20SP (2.0 kW)
3200 hours
1400W
2000W
CDXL-30 (3.0 kW)
1500 hours
2000W (67%)
3300W (110%)
CDXL-30SD (3.0 kW)
1500 hours
2100W
3000W
CDXL-30SP (3.0 kW)
1900 hours
2100W
3000W
Record new lamp information
i
The lamp serial number is an alphanumeric, user-defined field. Christie recommends choosing a
distinct and descriptive name for every individual lamp.
1. On the touch panel controller, tap Menu > Lamp > Change Lamp.
2. Enter a Lamp Type, Serial Number and Hours Used.
3. Tap Apply Lamp Change.
4. Tap Continue.
Add lamp end-of-life indicator
Specify the number of hours remaining before issuing an end-of-life indicator for the lamp.
1. On the touch panel controller, tap Menu > Lamp > Lamp life warning at (hours).
2. To specify the number of hours remaining before issuing an end-of-life indicator, enter a value
or use the plus and minus buttons to increase or decrease the value.
A value of zero disables the feature.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
55
Operation
3. Tap OK.
When the specified number of hours is reached, a Lamp Hours - past expiry warning is issued.
Work with lenses
The lens mount secures the projection lens to the projector and provides setup adjustments to
correct boresight, and control focus, zoom, and offsets.
A
Vertical offset knob
B
Horizontal offset knob
C
Horizontal boresight bolt
D
Vertical boresight bolt
E
Focus bolt
F
Lock/unlock lever
G
Stabilization screw
A
G
C
F
B
E
D
4. To electronically control the focus, zoom, and offsets, on the touch panel controller, tap the
Lens tab.
i
Calibrate the lens motors when any of the following conditions are met:
• After a lens change.
• After the projector is moved and/or jostled.
• After the lens motor IMCB has been replaced.
Select a channel
The projector uses pre-configured channels to determine how to display images from different
sources. Each channel file contains the optimum processing and display settings for the source.
Channels can be selected through the Home tab on the touch pad controller (TPC).
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
56
Operation
Enable warping and blending
Use edge blending to combine several projected images into one single, seamless image. Use
warping to project images on any surface shape.
1. Create the warp and blend files using the Twist application
For details, see the Twist 2.0 User Manual (P/N: 020-101380-xx).
2. Upload the warp and blend files to the projector.
For details, see the Twist 2.0 User Manual (P/N: 020-101380-xx).
3. On the touch panel controller, tap Main > Configuration > Geometry.
4. To select a warp setting, tap Geometry Correction and tap the required warp.
5. To select a blend setting, tap Edge Blending and tap the required blend.
6. To select a black level blend setting, tap Black Level Blending and tap the required black level
blend.
7. To turn off warping, blending, or black level blending, tap Off.
Send error notifications to specified devices
If an error occurs on the projector, notifications can be sent to three different devices.
1. On the touch panel controller, tap Menu > Communications > SNMP.
2. Tap Trap IP Address 1.
3. For the device you want to send error notifications to, enter the IP address.
4. Tap OK.
5. To add a second or third device, repeat steps 2 to 4.
6. Select the options you want to monitor.
Options include lamp fault, lamp life, power, fan stall, and thermal sensors.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
57
Menus
This section provides information and procedures for using projector menus. Use the projector
menus to adjust projector settings and view status information.
Touch panel controller
The touch panel controller (TPC) is a touch-sensitive screen. Use the TPC to control the projector,
manage sources, adjust the display, and view status information. The TPC is mounted on the rear of
the projector and can be adjusted to improve the TPC viewing angle. A side USB port can be used to
download log files and install software upgrades.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
58
Menus
For remote applications, the TPC can be dismounted from the projector and used with the optional
cable to allow projector control from a maximum distance of 100 ft (30 m).
Tab structure
The touch panel controller (TPC) windows are structured across a series of six tabs on the top of the
display:
Tab
Description
Home
Quickly add and select channels, display test patterns, activate the shutter and control the projector
power.
Menu
Access the projector controls and settings. Available submenus:
• Image Settings
• Lamp
• Configuration
• Communications
• General
Lens
Adjust the lens offset, focus, and zoom motors. These controls can be adjusted by either tapping the
required directional arrow, or by entering a numerical value.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
59
Menus
Tab
Description
Status
Display the status of projector control states and settings. The status windows are for reporting
purposes and all fields are read-only. For details, see Status tab details on page 61.
Admin
Display log files, access the interrogator, create files, perform restores, and perform upgrade
procedures. Available submenus:
• Upgrade—See Upgrade the projector software on page 63.
• Interrogator—See Run the projector interrogator on page 81.
• TPC Logs—See Save TPC log files on page 81.
• Backup—See Back up projector settings on page 63.
• Restore—See Restore settings from a local backup profile on page 64.
About
Display legal information regarding software licensing and usage agreements.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
60
Menus
Menu tab details
Menu
Description
Image Settings
Adjust image settings such as color space, sharpness, gamma function, ambient light, and
frame delay.
Lamp
Adjust the lamp power, calibrate the lamp, view lamp history and to input new lamp
information when performing a lamp change. Available options:
• Lamp Mode—See Track lamp intensity with LiteLoc on page 55.
• Lamp Power—See Adjust lamp power on page 53.
• Lamp life warning at (hours)—See Add lamp end-of-life indicator on page 55.
• LampLOC—See Adjust the lamp position with LampLOC on page 54.
• Lamp History—Display the history of all previously installed lamps. (Read-only)
• Change Lamp—See Record new lamp information on page 55.
Configuration
Adjust the projected image orientation, colors, and the projector Ethernet settings. Available
options:
• Color Correction—See Color correction on page 49.
• Image Orientation—See Select screen image orientation on page 44.
• EDID Window Mode—Inform the source device to split the 4K video raster into two or
four columns instead of four quadrants.
• EDID Timing—See Configure the projector for the 3D source on page 36.
• Diagnostics—Configure diagnostics such as freezing an image and selecting test patterns.
Communications
Adjust projector Ethernet settings and set notifications for projector errors. Available options:
• Device name—Set the name of the projector.
• Group name—Set the name of the group the projector belongs to.
• Ethernet Settings—See Set up the ethernet on page 43.
• SNMP—See Send error notifications to specified devices on page 57.
General
Adjust settings such as standby mode, auto power up, and video loop out. Provides current
date and time information
Status tab details
Window
Description
Alarms
Display the location and the fault condition for any active alarms.
Configuration
Display the projector model, serial number, output resolution and date of manufacture.
Cooling
Display the status of the liquid cooling module and the cooling fans.
Lamp Info
Display the current lamp information, such as: lamp state, hours, type, serial number and
power usage.
Serials
Display the serial numbers for all electrical components, such as: main control board,
backplane, image processor, formatter boards and option cards.
Signal
Display the status of the four available option card slots.
System
Display system hardware control settings, such as: projector hours, pitch/roll, lamp motor
status, lens motor status, and built-in self test.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
61
Menus
Window
Description
Temperatures
Display the operating temperatures as reported by the internal thermal sensors.
Versions
Display the hardware and software versions for all electrical components, such as: main
control board, backplane, image processor, formatter boards and option cards.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
62
Backup, Restore, and
Upgrade Projector Files
This section provides information and procedures for backing up, restoring, and upgrading projector
files.
Upgrade the projector software
1. On the touch panel controller, tap Admin > Upgrade.
2. Tap Upgrade.
3. To select the upgrade file, tap Browse.
4. In the Select Package dialog, navigate to the location where the upgrade file is stored.
5. Tap the upgrade file and tap Open.
6. To automatically restart the projector when the upgrade is complete, tap Restart when
update complete.
7. Tap Install.
Back up projector settings
1. On the touch panel controller, tap Admin > Backup.
2. To back up the settings, tap a backup file.
3. If required, enter or change the name.
4. Tap OK.
A message indicates the backup was successful.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
63
Backup, Restore, and Upgrade Projector Files
Export backup settings to an external device
1. If exporting settings from the touch panel controller (TPC), insert a USB flash drive (properly
formatted as FAT or NTFS) into the USB port on the side of the TPC.
or
If exporting settings from the PC application, skip to step 2.
If using the TPC, you cannot save to the TPC’s on-board CF flash memory. You must export the
settings to a USB flash drive. If using the PC application, you can export the files to location on
the hard drive, a USB flash drive, and so on.
2. On the TPC, tap Admin > Backup.
3. Tap Export.
4. To save the file, in the Choose backup file location dialog, navigate to the location where you
want export the file.
5. Tap Save.
Restore settings from a local backup profile
1. On the touch panel controller, tap Admin > Restore.
2. From the backup file list, tap the required file name.
3. Tap Restore.
4. At the prompt, tap OK.
Restore default settings
You need Service permissions to complete this procedure.
1. On the touch panel controller, tap Admin > Restore.
2. Tap Defaults.
3. Tap Restore.
Import file from an external device to restore
settings
1. If importing settings using the touch panel controller (TPC), insert the USB flash drive
containing the file into the USB port on the side of the TPC.
or
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
64
Backup, Restore, and Upgrade Projector Files
If importing settings using the PC application, skip to step 2.
If using the TPC, you must import the settings from a USB flash drive. If using the PC
application, you can import the files from a location on the hard drive, a USB flash drive, and so
on.
2. On the TPC, tap Admin > Restore.
3. Tap Import.
4. From the Choose file to restore dialog, navigate to the location where the file is stored.
5. Tap the file to select it.
6. Tap Open.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
65
Maintenance
This section provides information and procedures for performing projector maintenance. Read
through this section in its entirety before performing maintenance activities. When performing
projector maintenance, obey all warnings and precautions.
Never attempt to access the lamp compartment while the lamp is on. Wait at least 10
minutes after the lamp turns off before powering down, disconnecting from AC and opening
the lamp door.
The arc lamp operates at a high pressure that increases with temperature. Failure to allow
the lamp to sufficiently cool before handling, increases the potential for an explosion causing
personal injury or property damage.
Always wear manufacturer approved protective safety clothing (gloves, jacket, face shield)
whenever the lamp door is open or when handling the lamp.
When accessing the restricted access location for projector service or maintenance, avoid
exposure to the projector beam path by making sure to either:
• Power off the projector and disconnect from AC.
• Shutter the lamp to avoid emissions from the front aperture.
Danger! Failure to comply with the following results in death or serious injury.
ELECTRICAL SHOCK HAZARD! Always turn off, disconnect, and disengage all power sources
to the projector before servicing.
Failure to comply with the following could result in death or serious injury.
• Qualified technician required for all installations.
• Never operate the projector without all of it’s covers in place.
Caution! Failure to comply with the following could result in minor or moderate injury.
Only Christie accredited service technicians are permitted to open any enclosure on the
projector and only if the AC power has been fully disconnected.
Maintenance shutdown
This process is mandatory. Always perform these steps before beginning any inspection or
maintenance procedures on the projector.
1. If the projector is operating, turn it off and allow it to cool for a minimum of 10 minutes.
2. Set the projector breaker switch to the off position.
3. Set the lamp power supply’s three breaker switches to the off positions.
4. Disconnect the projector from AC power.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
66
Maintenance
Ventilation and cooling
Vents and louvers provide ventilation, both for intake and exhaust. Do not install the projector near
a radiator, heat register, or within an enclosure. To ensure adequate airflow, keep a minimum
clearance of 50 cm (20 inches) around the projector and never block or cover the vents.
Inspect and clean the airflow interlocks
Warning! Failure to comply with the following could result in death or serious injury.
Never operate the projector with the van switch removed or disabled.
The projector uses two airflow interlocks. Check and clean these switches to remove accumulated
dust or dirt that could impede movement.
•
Lamp blower vane switch, located within the lamp cooling compartment.
•
Extractor vane switch, located inside the top duct on the projector lid.
Inspect and clean the exhaust duct
Inspect the exhaust duct regularly and confirm that:
•
There are no obstructions or kinks within the ducting.
•
All air intake areas are unobstructed.
•
If using 2.0 or 3.0kW lamp, exhaust airflow must be at least 450 CFM (measured at the rigid
end of the duct when not connected to the projector).
i
•
600 CFM is required when ambient temperatures exceed 25°C or elevation (above sea level)
exceeds 3000 feet.
If using 4.5 or 6.0kW lamp, exhaust airflow bust be at least 600 CFM (measured at the rigid
end of the duct when not connected to the projector).
Inspect and clean the lamp blower
Notice. Failure to comply with the following may result in property damage.
Do not touch or bend the impeller blades or loosen the balancing weights.
A clogged blower impeller or motor can reduce air flow and lead to overheating and lamp failure.
1. Shut down the projector.
2. Remove the three screws securing the rear side cover.
3. Vacuum loose dirt from the lamp blower impeller.
4. If necessary, use a soft brush dampened with hot water.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
67
Maintenance
or
Fold a clean microfiber cloth and dampen with methanol and wipe evenly with the smooth
portion of the cloth that has no folds or creases. Do not apply finger pressure. Use the solution
in the cloth to collect the dirt.
For more details, see Maintenance shutdown on page 66.
Inspect and fill the coolant reservoir
Warning! Failure to comply with the following could result in death or serious injury.
HAZARDOUS SUBSTANCE! The coolant used in the projector contains propylene glycol. Use caution
when handling. Do not ingest.
Notice. Failure to comply with the following may result in property damage.
The coolant color may fade over time, however this does not impact the ability of the coolant to
exchange heat. Only use coolant recommended by Christie in this projector.
The liquid cooling module (LCM) circulates coolant through the digital micromirror device (DMD)
heat sinks. The coolant level should be checked every six months and should remain above the
minimum level indicator and free from particulate and/or fogginess.
Always use Christie approved Coolant Propylene Glycol (P/N: 003-103148-XX). Always remove
and refill the coolant reservoir outside of the projector and never overfill the reservoir beyond the
top of the window. Use caution not to spill or let any of the coolant drip on or near the electronics.
Remove the liquid cooling reservoir
1. Shut down the projector.
2. Remove the front top cover.
3. Remove the radiator air filter.
4. Disconnect the blower on the LCM pump.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
68
Maintenance
5. Disconnect the communications harness from the coolant reservoir.
6. Disconnect the coolant hoses from the coolant reservoir.
7. Remove the three screws securing the reservoir bracket to the projector base plate.
8. Lift and remove the reservoir from the projector.
9. Refill the reservoir as needed.
10. Replace the cap.
11. To reinstall the liquid cooling reservoir, repeat these steps in reserve order.
12. Check for leaks, especially for any hoses that were removed around the filler cap.
13. Check for proper flow from the liquid cooling module.
For more details, see Maintenance shutdown on page 66.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
69
Maintenance
Filtration
Notice. Failure to comply with the following may result in property damage.
Use only high efficiency Christie approved filters: light engine filter (five-pack)—P/N:003-001184-XX,
liquid cooling radiator filter—P/N: 003-003082-XX, and LAD filter (three-pack)—P/B:03-001982-51P.
Never operate the projector without the filter installed. The air filters in this product cannot be
cleaned thoroughly enough for reuse and can lead to the contamination of optical components.
Replace the light engine air filter
This filter is located on the lens side of the projector behind the air filter cover. Check the condition
of this filter monthly. Replace the light engine air filter when replacing the lamp, or sooner when
operating the projector in a dusty or dirty environment.
1. Release the two tabs on the air filter cover.
2. Lift up the cover enough for the bottom tabs to clear the frame and remove.
3. Slide the air filter out from behind the air filter cover and discard.
4. Insert the new air filter with the airflow indicator facing toward the projector.
This ensures proper particle filtration.
5. To complete the installation, align the bottom tabs and repeat these steps in reverse order.
Replace the liquid cooling air filter
This filter is located on front lamp-side of the projector, behind a small air filter cover. Check the
condition of this filter monthly. Replace the liquid cooling air filter when refilling the liquid cooling
module, or sooner when operating the projector in a dusty or dirty environment.
1. Release one tab on the air filter cover.
2. Rotate the top towards you and lift up to remove.
3. Slide the air filter out and discard.
4. Insert the new air filter with the airflow indicator facing toward the projector.
5. Install the air filter cover.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
70
Maintenance
Replace the laminar airflow device filter
The laminar airflow device (LAD) filter is attached to the light engine assembly handle in the light
engine compartment. Inspect the LAD filter every six months.
1. Shut down the projector.
2. Unlock and remove the front top cover.
3. Unlock and remove the light engine lid.
4. Remove the two screws securing the laminar airflow device filter (LAD) assembly to the
bracket.
5. Pull out and replace the LAD filter.
6. To reinstall, repeat these steps in reverse order.
For more details, see Maintenance shutdown on page 66.
Lamps
Danger! Failure to comply with the following results in death or serious injury.
• Lamp replacement must be performed by a qualified service technician only.
• EXPLOSION HAZARD. Wear authorized protective clothing (P/N: 598900-095) whenever the lamp
door is open and when handling the lamp. Ensure those within the vicinity of the projector are also
wearing protective safety clothing. Recommended protective clothing includes, but may not be
limited to a polycarbonate face shield, protective gloves, and a quilted ballistic nylon jacket or a
welder’s jacket. Protective clothing recommendations are subject to change. Any local or federal
specifications take precedence over Christie recommendations.
• Never twist or bend the quartz lamp body. Use the correct wattage lamp supplied by Christie.
• Never attempt to remove the lamp when it is hot. The lamp is under extremely high pressure when
hot and may explode. Allow the lamp to cool completely before replacing.
Warning! Failure to comply with the following could result in death or serious injury.
• Possibly hazardous optical radiation emitted from this product. (Risk group 3).
• Thermal radiation emitted from this product may cause burns. (Risk group 3).
Always perform these steps before inspecting, removing, or installing any part of the lamp system:
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
71
Maintenance
1. Shut down the projector, disconnect from power, and let it cool.
2. Put on the protective clothing and face shield.
3. Use the key to open the lamp door and access the lamp compartment.
Do not lean, or place heavy objects on the open lamp door.
For more details, see Maintenance shutdown on page 66.
Adjust the yoke assembly
After installing the lamp, to ensure optimal operation of the lamp,
check that the anode yoke is in the correct position for the lamp
type:
Lamp
Type
Anode Yoke Position
2.0 kW
CDXL-20
3.0 kW
CDXL-20SP
Move the lamp cradle to the rear position,
which is approximately 1” closer to the
reflector.
CDXL-30
Reflector
Anode
Yoke
Assembly
CDXL-30SP
CDXL-30SD
The lamp extension nut is installed when using a CDXL-30SD lamp.
Remove the nut if you are not using a CDXL-30SD lamp.
5mm hex key
required
Inspect and clean the lamp
Danger! Failure to comply with the following results in death or serious injury.
Always disconnect the projector from AC power and wear authorized protective safety gear.
•
Check the contact surfaces of the anode (positive) and the cathode (negative) connections for
cleanliness.
•
Clean electrical contact surfaces regularly to prevent contact resistance from scorching
connectors. Use an approved contact cleaner such as Sticklers Fiber Optic Cleaner.
•
Verify that all electrical and lamp connections are secure.
•
Use lint-free lab gloves.
Remove dust from the lamp
1. Brush most of the dust off with a camelhair brush or use a dust-free blower.
2. If some dust remains, leave it. Some dust is inevitable. Avoid unnecessary cleaning.
Remove fingerprints, smudges, or oil from the lamp
1. Brush most of the dust off with a camelhair brush or use a dust-free blower.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
72
Maintenance
2. Fold a microfiber cloth and wipe the remaining dust particles off the lamp with the smooth
portion of the cloth that has no folds or creases. Do not apply finger pressure. Instead, use the
tension in the folded cloth to remove the dust.
Inspect and clean optics
Notice. Failure to comply with the following may result in property damage.
• A small amount of dust or dirt on the lens has minimal effect on image quality-to avoid the risk of
scratching the lens, clean the lens only if absolutely required. The reflector and projection lens may
be inspected and cleaned as per the following instructions. Any other optical maintenance should
only be performed by qualified service technicians.
• Always wear powder free latex gloves when handling and cleaning projector optics.
• Only use solvents if dirt remains after dusting with compressed air.
• Do not reuse lens tissues. Use a clean tissue for each cleaning attempt.
• Handle optics by their edges.
Inspect these components periodically in a clean, dust-free environment using a high-intensity light
source or flashlight. Clean them only when dust, dirt, oil, fingerprints, or other marks are obvious.
Never touch an optical surface with bare hands. Always wear lint-free lab gloves.
The following tools are recommended for removing dust or grease:
•
Powder free latex gloves
•
Soft camel-hair brush
•
Dust-free blower—filtered dry nitrogen blown through an anti-static nozzle
•
Lint-free lens tissue, such as Lensx 90 tissue or Newport Optics cleaning tissue
•
For the lens only—lens cleaning solution and microgiber cloth
•
For the reflector only—Methanol
•
Isopropyl Alcohol Reagent Grade (ACS) 99.9%
•
Acetone Reagent Grade (ACS)
•
Optical grade cotton swabs with wooden stems
•
Sticklers Fiber Optic Cleaner (can be used on all optical components)
•
A bright, portable illumination device such as an LED flashlight
Remove dust from the projection lens
1. Brush most of the dust off with a camel-hair brush or use a dust-free blower.
2. Fold a microfiber cloth and wipe the remaining dust particles off the lens with the smooth
portion of the cloth that has no folds or creases. Do not apply finger pressure. Instead, use the
tension in the folded cloth to remove the dust.
3. If significant dust remains on the lens surface, dampen a clean microfiber cloth with lens
cleaning solution and wipe gently until clean.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
73
Maintenance
Remove fingerprints, smudges, or oil from the projection lens
Do not use a cleaning solvent that contains ammonia. Avoid lens contact with Xylene and Ether.
i
1. Brush most of the dust off with a camelhair brush or use a dust-free blower.
2. Wrap a lens tissue around a swab and soak it in lens cleaning solution. The tissue should be
damp but not dripping.
3. Gently wipe the surface using a figure eight motion.
4. Repeat until the blemish is removed. Clean the lens only if absolutely required.
Remove the projection lens
5. Close the shutter.
6. Attach a large lens cap to the front of the lens to avoid damage.
7. Release the lens locking lever (up position).
8. Pull the lens straight out and attach a small lens cap to the rear of the
lens to avoid damage.
Warning! Failure to comply with the following could result in death or serious injury.
The lens tether must be installed for overhead installation.
For more details, see Maintenance shutdown on page 66.
Install the projection lens
1. Make sure the lens locking lever is in the up position.
2. If attached, remove the rear lens cap from the lens.
3. Slide the lens into the lens mount, aligning all connections.
i
Always install the lens with UP label in the top position. This assists in achieving consistent
boresight alignment each time the lens is replaced.
4. Secure the lens with the lens locking lever (down position).
5. Calibrate the lens motors, as described below.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
74
Maintenance
Calibrate the lens motors
If the lens motors are not calibrated properly, implications may include:
•
Incorrect reporting of the lens motor position.
•
Inability to use the full range of the lens motors.
•
Lens motors traveling outside of the pre-defined keep-out area.
•
Damage to the projector.
Calibrate the lens motors when any of the following conditions are met:
•
After a lens change.
•
After the projector is moved and/or jostled.
•
After the lens motor IMCB has been replaced.
To calibrate the lens motors, on the touch panel controller, tap Lens > Calibrate Lens Motors.
Reset lens to home position
To reset the lens to the default home position, on the touch panel controller, tap Lens > Reset to
Home Position.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
75
Troubleshooting
This section provides information and procedures for resolving common projector issues. If a
projector issue cannot be resolved, contact a Christie accredited service technician.
Projector does not power on
•
Make sure the projector circuit breaker is set to the on position.
•
Check the status LEDs on the rear corners of the projector for a fault condition. A flashing red
LED indicates an alarm or warning preset with the projector and a problem that must be
addressed.
•
Use the touch panel controller (TPC) status menu to troubleshoot further.
Lamp does not ignite
•
Check and correct all interlock failures.
•
Verify that the lamp has been installed and connected properly. Verify the condition of the lamp
and that is not blackened or otherwise damaged.
•
Verify the number of hours the lamp has operated. A lamp nearing the end of its operational life
should be replaced.
Lamp suddenly turns off
•
Increase the lamp power.
•
Review and correct all interlock failures.
•
Ensure the TPC has no temperature or fan RPM warnings. If all fans are running normally and
the air filters are not blocked, the ambient air temperature may exceed the maximum operating
specification. If possible, reduce the ambient temperature.
•
Ensure no heat sources are exhausting into the projectors intake, or move the projector to a
cooler environment.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
76
Troubleshooting
•
Verify the number of hours the lamp has operated. A lamp nearing the end of its operational life
should be replaced.
•
Check for a cross-connected condition.
A cross-connection hazard can occur when installing multiple projectors at once. A fire hazard
exists if a lamp power supply interlock cable is connected to a different projector than its lamp
power cables.
Flicker, shadows or dimness
•
Make sure the shutter is fully open.
•
Verify that a LampLOC calibration is not already in progress.
•
Perform a LampLOC calibration.
•
Increase the lamp power. Lamps which are near end of service may not operate reliably at a
lower power setting.
LampLOC not working
•
If the Auto LampLOC option is not working, on the touch panel controller, tap Menu > Lamp
> LampLOC and adjust the lamp position manually. Observe screen brightness by adjusting
the X, Y and Z values or use a light meter to check for changes in brightness.
•
Check that the flat part of the anode end of the lamp (if applicable) faces up in the anode yoke.
Touch panel controller is blank
•
If the touch panel controller (TPC) display is blank, make sure the TPC communication harness
is connected securely.
Blank screen, no display of image
•
Make sure both lens caps have been removed from the projection lens.
•
Make sure the lamp is on.
•
Make sure that all power connections are good.
•
Make sure the shutter is fully open.
•
Make sure that any test pattern (other than a full black test pattern or test pattern = none)
displays properly.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
77
Troubleshooting
Cannot communicate with projector
•
Make sure the computer and the projector are both connected to the network.
•
Make sure that all input devices have the same subnet mask and unique IP addresses.
Inaccurate display colors
•
Adjust the color, tint, color space, and color temperature settings of the input source.
•
On the touch panel controller, tap Menu > Configuration > Color Correction and verify the
settings are correct.
Display is not rectangular
•
Verify the projector is level and the lens surface and screen are parallel to one another.
•
Adjust the vertical offset of the lens mount.
Display has suddenly frozen
•
If the source is frozen, restart the source device.
•
If the source is not frozen, restart the projector.
Display is jittery or unstable
•
Verify that the input device is connected properly. If the input device is not connected properly,
the projector repeatedly attempts to display an image.
•
The horizontal or vertical scan frequency of the input signal may be out of range for the
projector.
For more details, see Specification on page 82
Incoming signal(s) problems
The Status tab > Signal group contains information about all the signals that the projector receives.
A properly configured system shows the frequency and a status of Master or Locked for each input
in the selected channel.
•
If one or more of the signals are listed as No signal, verify that the source is properly
configured and the cables are secure between the source and the projector.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
78
Troubleshooting
•
If one or more of the signals are listed as Inactive, either an incorrect channel has been
selected or the cables are not plugged into the correct inputs.
•
If one or more of the signals is listed as Unlocked or Out of phase, the source is not properly
frame locked to the master signal. This usually occurs when two independent sources are not
locked together. Verify the setup of the sources. If the sources are locked together, contact
Christie Technical Support for help.
Touch panel controller or projector head
problems on startup
Check the following to determine if the touch panel controller (TPC) or the projector head are
experiencing problems on startup.
The projector has two sets of LEDs to help distinguish how far into the start-up process it is when a
problem occurs.
For more details, see LED expected behavior on power up on page 53.
The Projector LEDs or the MCPU board power LED are not on
Solution 1
If AC power has been applied to the projector head, verify the power source.
Solution 2
If the AC power source is good and the AC power is applied to the projector head, check the LVPS
and all the harnessing going to it inside the projector.
The MCPU board power LED is not on
If the AC power is applied to the projector head and the projector’s LEDs turn on, the MCPU board
or the ABP must be replaced. Replace the MCPU board first and if the problem is not resolved,
replace the ABP.
•
If replacing the MCPU board, indicate that the Power LED is non-functional.
•
If replacing the ABP, indicate that power did not reach the MCPU board.
MCPU board power LED behavior
•
Solid yellow—The MCPU board must be replaced. Indicate that the MCPU board failed to
initialize.
•
Blinking red—The MCPU board must be replaced. Indicate that the MCPU board failed to
initiate the control FPGA.
•
Blinking yellow/green—The MCPU board is running in recovery mode and needs a software
upgrade followed by a AC cycle of the projector head.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
79
Troubleshooting
Touch panel controller does not connect
If the projector LEDs display solid yellow and the touch panel controller (TPC) has power but does
not connect, the projector head is fine. However, a problem could exist between the TPC and the
MCPU board.
•
Disconnect the corded harness to the TPC and reconnect it. You may need to replace the corded
harness.
•
Check for physical damage to the harness between the external TPC port and the ABP. Try
changing the internal harness.
3D synchronization problems
A direct input 3D source requires a 3D external sync. The Status tab > Signal group has a 3D Sync
item that displays “Valid 3D sync” if the incoming sync is correct.
•
If the No 3D sync (using internal sync) message is displayed, no sync signal is detected on the
3D Sync In port.
•
If the Invalid 3D sync (using internal sync) message is displayed, the sync signal is present but
it is either not locked or is out of phase with the vsync of the master signal.
In both cases, the sync from the 3D source must be verified.
Left and right eye are reversed
Provided the Confirming Emitter setup was successfully performed, the 3D source in combination
with the 3D external sync may be reversing the frames. To correct this, on the touch panel
controller, tap Main > 3D Settings > Invert Left/Right Eye.
Frame multiplication applied to incoming video
signals when not required
Frame multiplication is enabled when 3Dmode is on (auto). Disabling this setting prevents frame
multiplication.
With 3D mode enabled, Mirage 4K35 projectors apply the following multiplication rules:
•
Incoming ~48Hz => Outgoing ~144Hz (triple)
•
Incoming ~50Hz => Outgoing ~150Hz (triple)
•
Incoming ~60Hz => Outgoing ~120Hz (double)
For more details, refer to the TDM–3D Mode (Mirage 4K) section in the Christie D4K and Mirage 4K
Serial API Commands Technical Reference (P/N: 020-101258-XX).
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
80
Troubleshooting
Run the projector interrogator
The interrogator captures diagnostic information Christie personnel uses to help diagnose and
correct projector issues. If a projector issue cannot be resolved, Christie personnel may request an
interrogator file from the projector.
Log files are compressed into a standard zip file.
1. On the touch panel controller, tap Admin > Interrogator.
2. Tap Create File.
3. Click Continue.
4. In the Choose destination directory dialog, navigate to the location where you want to store the
log file.
5. Tap Save.
Save TPC log files
TPC log files can help you identify and correct issues with the touch panel controller. If a projector
issue cannot be resolved, Christie personnel may request a TPC log file from the projector.
Log files are compressed into a standard zip file.
1. On the touch panel controller, tap Admin > TPC Logs.
2. Tap Create File.
3. In the Choose destination directory dialog, navigate to the location where you want to store the
log file.
4. Tape Save.
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
81
Specification
Specification
This section provides detailed Mirage 4K25 specifications. Due to continuing research, specifications
are subject to change without notice.
Display
Panel Resolution and Refresh Rate
Pixel format (H x V square pixels)
4096 x 2160
Processing path
23.97 - 60Hz
Achievable Brightness (Measured at Screen Center)
Nominal
2.0 kW (CDXL-20)
10,000 lumens
2.0 kW (CDXL-20SP)
10,000 lumens
3.0 kW (CDXL-30)
18,000 lumens
3.0 kW (CDXL-30SD)
25,000 lumens
3.0 kW (CDXL-30SP)
19,000 lumens
Achievable Contrast Ratio
450:1 ANSI, up to 2000:1 Full Frame ON/OFF
Color and Grayscale Resolution
Displayable colors
35.2 trillion
Grayscale resolution
45 bits total linear, 25 bits per RGB component
White Point
Nominal white
(full white, after calibration)
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
y = 0.351 ± 0.002
x = 0.314 ± 0.002
82
Specification
Gamma
Nominal
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
2.2 ± 5%
83
Input
Configuration
Four-Port
Four-Port
Four-Port
Four-Port
Two-Port
Two-Port
Four-Port
Four-Port
Two-Port
Four-Port
Four-Port
Two-Port
Four-Port
Four-Port
Two-Port
Four-Port
2D/
3D
3D
3D
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
3D
3D
3D
3D
3D
3D
3D
3D
3D
3D
3D
3D
3D
3D
Direct
Direct
Direct
Direct
Direct
Direct
Direct
Direct
Direct
DualInput
DualInput
DualInput
DualInput
DualInput
Direct
Direct
3D
Type
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
4K, QHD
Input
Format
48, 50
48, 50
48, 50
60
60
60
60
60
60
60
60
60
60
60
120
120
HDMI 1.4a
DisplayPort
1.1a
DisplayPort
1.1a
DVI (Single)
DVI (Dual)
3G-SDI
HDMI 1.4a
DisplayPort
1.1a
DisplayPort
1.1a
3G-SDI
DVI (Dual)
DisplayPort
1.1a
HDMI 1.4a
DisplayPort
1.1a
DVI (Dual)
DisplayPort
1.1a
Frame Interface
Rate
(Hz)
Mirage signal connectivity
2X THIC
2x TDPIC
2x TDPIC
4x DDIC
2x DDIC
2x 3GIC
2x THIC
2x TDPIC
2x TDPIC
4x 3GIC
4x DDIC
4x TDPIC
4x THIC
4x TDPIC
4x DDIC
4x TDPIC
Cards
4
2
4
4
2
4
4
2
4
8
4
4
8
8
4
4
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Cables RGB/
4:4:4
8-bit
X
X
X
X
X
X
X
X
X
X
RGB/
4:4:4
10-bit
X
X
X
RGB/
4:4:4
12-bit
X
X
X
X
X
X
4:2:
2 8bit
X
X
X
X
X
X
X
X
4:2:
2
10bit
X
X
X
X
X
X
4:2:
2
12bit
Specification
84
Input
Configuration
Two-Port
One-Port
One-Port
One-Port
One-Port
One-Port
One-Port
One-Port
One-Port
One-Port
One-Port
One-Port
One-Port
One-Port
One-Port
Four-Port
Four-Port
One-Port
One-Port
2D/
3D
3D
3D
3D
3D
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
3D
3D
3D
3D
3D
3D
3D
3D
3D
3D
3D
2D
2D
2D
2D
Direct
Direct
Direct
Direct
Direct
Direct
Direct
Direct
Direct
Direct
DualInput
DualInput
DualInput
DualInput
Direct
3D
Type
2K, HD
2K, HD
4K, QHD
4K, QHD
2K, HD
2K, HD
2K, HD
2K, HD
2K, HD
2K, HD
2K, HD
2K, HD
2K, HD
2K, HD
2K, HD
2K, HD
2K, HD
2K, HD
4K, QHD
Input
Format
120
120
120
120
48, 50
48, 50
48, 50
48, 50
60
60
60
60
120
120
60
60
60
60
48, 50
DVI (Dual)
DisplayPort
1.1a
DVI (Dual)
DisplayPort
1.1a
DVI (Single)
3G-SDI
HDMI 1.4a
DisplayPort
1.1a
DVI (Single)
3G-SDI
HDMI 1.4a
DisplayPort
1.1a
DVI (Dual)
DisplayPort
1.1a
DVI (Single)
3G-SDI
HDMI 1.4a
DisplayPort
1.1a
DVI
Frame Interface
Rate
(Hz)
1x DDIC
1x TDPIC
4x DDIC
4x TDPIC
1x DDIC
1x 3GIC
1
1
4
4
1
1
1
1
1x TDPIC
1x THIC
1
1
1
1
1
1
2
2
2
2
2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Cables RGB/
4:4:4
8-bit
1x DDIC
1x 3GIC
1x THIC
1x TDPIC
1x DDIC
1x TDPIC
2x DDIC
1x 3GIC
1x THIC
1x TDPIC
2x DDIC
Cards
X
X
X
X
X
X
X
X
X
RGB/
4:4:4
10-bit
X
X
X
RGB/
4:4:4
12-bit
X
X
X
X
X
X
4:2:
2 8bit
X
X
X
X
X
X
X
X
X
4:2:
2
10bit
X
X
X
X
X
X
4:2:
2
12bit
Specification
85
Specification
•
4K = 4096 x 2160
•
QHD = 3840 x 2160
•
2K = 2048 x 1080
•
HD = 1920 x 1080
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
86
Specification
Optional Input cards
Input Card
Part Number
Dual 3G SD/HD-SDI
108-313101-02+
Dual Link DVI
108-312101-02+
Twin HDMI
108-311101-XX
Twin DisplayPort
108-451101-XX
Additional Information
Analog signals are not supported for this input card; therefore
VGA port and VGA to DVI converters are not supported.
To determine which SDI signal types are officially supported, see Mirage signal connectivity on page
84.
Control signal compatibility
Ethernet Port
Interface
10Base-T/100Base-TX
Connector
Female RJ-45
USB
Connector
Type B
Interface
USB to serial (bit rate identical to RS232)
3D Sync
Connector
BNC Male
Interface
TTL inputs and outputs
RS422
Connector
9-pin subminiature D, female
Bit rate
115,200 bps
Data format
1 start bit, 8 data bits, 1 stop bit, no parity
RS232 IN
Connector
9-pin subminiature D, female
Bit rate
115,200 bps
Data format
1 start bit, 8 data bits, 1 stop bit, no parity
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
87
Specification
RS232 OUT
Connector
9-pin subminiature D, male
Bit rate
115,200 bps
Data format
1 start bit, 8 data bits, 1 stop bit, no parity
Temperature sensor thresholds
The projector shutdowns within one minute of an error threshold being reached.
Location
Warning
(°C)
Error
(°C)
Integrator rod
110
120
Prism
60
70
Air intake
44
49
Lamp exhaust
85
95
MCPU
70
95
ABP
82
95
HIP scaler
82
95
HIP warp red
82
95
HIP warp green
82
95
HIP warp blue
82
95
Formatter red
82
95
DMD red
63
68
Formatter green
82
95
DMD green
63
68
Formatter blue
82
95
DMD blue
63
68
Option card 1
80
95
Option card 2
80
95
Option card 3
80
95
Option card 4
80
95
EVB
70
95
Lens MCB
75
95
v1.0x software only; removed in v1.1.0+ software
Lamp MCB
70
95
v1.0x software only; removed in v1.1.0+ software
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
Remarks
88
Specification
Warning thresholds for fans
All fan warnings are set to ~75% of their normal operating speeds.
Location
Warning RPM
Light engine intake (fan 5)
3300
Light engine intake (fan 6)
3300
Light engine intake (fan 8)
3300
Formatter—green blower (fan 7)
3500
Laminar airflow device (fan 4)
5900
Electronics intake (fan 10)
5700
Electronics intake (fan 11)
5700
Electronics intake (fan 12)
5700
Image processor warp blower (fan 9)
2400
Electronics exhaust (fan 1)
3400
Electronics exhaust (fan 2)
3400
Liquid cooling radiator (fan 3)
1800
Image processor scaler (fan 13)
5100
Warning threshold for liquid cooling module
Location
Warning
Flow meter
0.2mL/min
Liquid cooling pump
180 RPM
Touch panel controller
TPC 650H
Type of display
Color VGA TFT LCD, backlit
Display size
144.8 mm (5.7 inches) diagonal
Display resolution (H x V pixels)
640 x 480
Maximum dimensions (W x H x D)
195 mm x 148 mm x 58 mm
Integrated operating system
Microsoft Windows® XPe
Communication interface with projector
10/100/1000 BaseT Ethernet
Power requirement
0.71A maximum at 24VDC ± 10%
Interface connector
12-pin circular connector (push-pull)
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
89
Specification
Power requirements
AC Input
Voltage range
200 - 240 VAC
Line frequency
50 - 60 Hz nominal
Inrush current
45 A maximum
Current consumption
23 A maximum (at 200 VAC)
Power consumption
4500 W maximum
Current rating of AC input
30 A maximum (specified wall breaker)
Lamp
Xenon Bubble Lamp
Type
Xenon bubble
CDXL-20
1400W - 2000W
CDXL-20SP
1400W - 2000W
CDXL-30
2100W - 3000W
CDXL-30SP
2100W - 3000W
Average life
CDXL-20
2400 hours
CDXL-20SP
3200 hours
CDXL-30
1500 hours
CDXL-30SP
1900 hours
Wait time between lamp strikes
2 minutes minimum
NOTE: Projectors typically force a 10 minute cool down period. Make sure not to re-strike the lamp any sooner
than two minutes into this cool down period since hot re-strikes reduce lamp life.
Physical specifications
Overall size (L x W x H)
(including lens mount, stack, and feet)
1298 x 648 x 483 (mm)
51.1 x 25.5 x 19.0 (inches)
Projector head weight
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
90
Specification
Without lens mount cover
124 kg (273 lbs)
Shipping (includes packaging)
156 kg (344 lbs)
Operating position
Rotation about projection axis
±15 degrees maximum
Tilt of projection axis from horizontal
±15 degrees maximum
Regulatory
This product conforms to the following regulations related to product safety, environmental
requirements and electromagnetic compatibility (EMC).
Safety
•
CAN/CSA C22.2 No. 60950-1
•
UL 60950-1
•
IEC 60950-1
•
EN60950-1
Approvals
This product shall conform to all relevant directives, standards, safety, health and environmental
rules and regulations required for the product to be sold in: USA/Canada, EU, Norway, Australia/
New Zealand, Kuwait, China, Korea, Japan, Mexico, Ukraine, Russia, South Africa, and Saudi Arabia
international packaging recycling mark requirements:
•
EU Directive (94/62/EC) on packaging and packaging waste;
•
China packaging recycling mark standard (GB18455-2001).
Electro-magnetic compatibility
Emissions
FCC CFR47, Part 15, Subpart B, Class A - Unintentional Radiators
CISPR 22/EN 55022, Class A - Information Technology Equipment
Immunity
CISPR 24/EN55024: EMC Requirements—Information Technology Equipment
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
91
Specification
Environmental
EU Directive (2011/65/EU) on the restriction of the uses of certain hazardous substances (RoHS) in
electrical and electronic equipment and the applicable official amendment(s)
EU Regulation (EC) No. 1907/2006 on the registration, evaluation, authorization and restriction of
chemicals (REACH) and the applicable official amendment(s).
EU Directive (2012/19/EU) on waste and electrical and electronic equipment (WEEE) and the
applicable official amendment(s)
China Ministry of Information Industry Order No.39 (02/2006) on the control of pollution caused by
electronic information products, hazardous substances concentration limits (SJ/T11363-2006), and
the applicable product marking requirements (SJ/T11364-2006)
Environment
Operating Environment
Temperature
10 to 35°C (50 to 95°F)
Humidity (non-condensing)
20 to 80%
Altitude
0 to 3000 meters
Maximum ambient temperature
35°C
Non-Operating Environment
Temperature
-25 to 65°C (-13 to 149°F)
Humidity (non-condensing)
0 to 95%
Accessories
Standard (Included with product)
• Lens plug (required for shipping when lens is not installed to prevent contamination of critical optical
components)
• Nylon safety strap with clip (required to secure projector to tabletop or optional rack mount)
• Touch panel controller (TPC) with interface cable
• Shroud
• Light engine removal tool
• Convergence tool
• Warranty card
• Web registration form
• Low security keys
Lenses (sold separately)
Description
Part Number
Lens 0.72:1
113-104106-XX
Lens 0.9:1
38-809071-XX
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
92
Specification
Lenses (sold separately)
Description
Part Number
Lens 1.13-1.31:1
129-104106-XX
Lens 1.63-1.63:1
129-105107-XX
Lens 1.63-2.17:1
129-106108-XX
Lens 1.98-2.71:1
129-107109-XX
Lens 3.0-4.3:1
129-108100-XX
Lens 3.89-5.43:1
129-109101-XX
Lens 5.0-7.69:1
129-110103-XX
Note: The lens throw values in the lens name may differ from the actual throw ratios. For details, see the 4K
Lens Throw Technical Reference (P/N: 020-100904-XX).
Replacement Lamps (sold separately)
Description
Part Number
CDXL-20
003-000598-02
CDXL-20SP
003-004251-01
CDXL-30
003-000599-02
CDXL-30SD
003-001165-01
CDXL-30SP
003-004252-01
Replacement Air Filters (sold separately)
Description
Part Number
Light engine filter (five-pack)
003-001184-XX
Liquid cooling radiator filter
003-003082-XX
LAD filter (three-pack)
03-001982-51P
Other Accessories (sold separately)
Description
Part Number
Rack stand
108-282101-XX
Bracket foot lock used with optional rack stand
116-100101-XX
High-contrast Internal Aperture kit
38-813028-51
Service Manual
available online
Firmware Installation program
available online
Coolant propylene glycol
003-103148-XX
TPC remote cable
003-111169-XX
Heat extractor kit
38-814008-61
Mirage 4K25 User Manual
020-101361-02 Rev. 1 (01-2015)
93
*000-105002-02*
ASSY TECH DOCS Mirage 4K25
Corporate offices
Worldwide offices
USA – Cypress
ph: 714-236-8610
Australia
ph: +61 (0) 7 3624 4888
Canada – Kitchener
ph: 519-744-8005
Brazil
ph: +55 (11) 2548 4753
Consultant offices
China (Beijing)
ph: +86 10 6561 0240
Italy
ph: +39 (0) 2 9902 1161
China (Shanghai)
ph: +86 21 6278 7708
Eastern Europe and
Russian Federation
ph: +36 (0) 1 47 48 100
France
ph: +33 (0) 1 41 21 44 04
Germany
ph: +49 2161 664540
India
ph: +91 (080) 6708 9999
Singapore
ph: +65 6877-8737
Japan (Tokyo)
ph: 81 3 3599 7481
Spain
ph: + 34 91 633 9990
Korea (Seoul)
ph: +82 2 702 1601
United Arab Emirates
ph: +971 4 3206688
Republic of South Africa
ph: +27 (0)11 510 0094
United Kingdom
ph: +44 (0) 118 977 8000
For the most current technical documentation, please visit www.christiedigital.com